HP ProLiant ML310 Generation 3 Server Maintenance and Service Guide
May 2006 (Fourth Edition) Part Number 393771-004
Copyright 2005, 2006 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein. Microsoft and Windows are U.S. registered trademarks of Microsoft Corporation. Intel and Pentium are U.S. registered trademarks of Intel Corporation. Linux is a U.S. registered trademark of Linus Torvalds. May 2006 (Fourth Edition) Part Number 393771-004

Audience assumptions

This document is for the person who installs, administers, and troubleshoots servers and storage systems. HP assumes you are qualified in the servicing of computer equipment and trained in recognizing hazards in products with hazardous energy levels.

Contents

Customer self repair..... 5
Parts only warranty service.... 5
Illustrated parts catalog.... 15
Mechanical components..... 15 System components.... 19
Removal and replacement procedures... 23
Required tools..... 23 Safety considerations.... 23 Preventing electrostatic discharge.... 23 Server warnings and cautions.... 24 Rack warnings and cautions.... 24 Preparation procedures.... 25 Power down the server.... 25 Remove the server from the rack.... 25 Remove the bezel.... 25 Access panel..... 26 Hot-plug SCSI hard drive.... 27 Hot-plug SAS and SATA hard drives.... 27 Non-hot-plug hard drive cage.... 28 Hard drive (non-hot-plug).... 29 Hot-plug SCSI, SAS, or SATA hard drive cage.... 30 Hot-plug SCSI backplane.... 30 Hot-plug SAS or SATA backplane.... 31 Diskette drive..... 32 CD-ROM/DVD-ROM drive.... 32 Air baffle..... 33 Power supply..... 33 DIMM..... 34 Processor assembly..... 36 PCI expansion board.... 38 Fan assembly..... 39 Power button/LED board.... 39 Battery..... 40 System board..... 41

Cabling..... 43

Hot-plug SCSI hard drive cabling.... 43 Non-hot-plug SCSI hard drive cabling.... 44 Hot-plug SATA hard drive cabling.... 44 Non-hot-plug SATA hard drive cabling... 45 SAS hard drive cabling.... 45

Diagnostic tools.... 46

Survey Utility..... 46 Array Diagnostic Utility.... 46 HP Insight Diagnostics.... 46 Integrated Management Log.... 47 ROMPaq disaster recovery.... 47
Component identification.... 48
Front panel components..... 48 Front panel LEDs and buttons.... 49 Rear panel components.... 50 Rear panel LEDs.... 50 System board components.... 51 System maintenance switch.... 52 System board LEDs..... 53 System LEDs and internal health LED combinations.... 54 SCSI IDs..... 55 Hot-plug SCSI hard drive LEDs.... 55 Hot-plug SCSI hard drive LED combinations... 56 Hot-plug SAS and SATA device numbers.... 57 SAS and SATA hard drive LEDs..... 57 SAS and SATA hard drive LED combinations.... 57 Fans..... 58

Specifications..... 60

Server specifications..... 60 Environmental specifications.... 60 Hot-plug power supply calculations... 61 1.44-MB diskette drive specifications.... 61 CD-ROM drive specifications.... 62 Hard drive specifications.... 62 DVD-ROM drive specifications.... 63
Acronyms and abbreviations.... 65 Index..... 67

Customer self repair

HP products are designed with many Customer Self Repair (CSR) parts to minimize repair time and allow for greater flexibility in performing defective parts replacement. If during the diagnosis period HP (or HP service providers or service partners) identifies that the repair can be accomplished by the use of a CSR part, HP will ship that part directly to you for replacement. There are two categories of CSR parts:

Removal and replacement procedures
Required tools..... 23 Safety considerations.... 23 Preparation procedures..... 25 Access panel..... 26 Hot-plug SCSI hard drive.... 27 Hot-plug SAS and SATA hard drives.... 27 Non-hot-plug hard drive cage.... 28 Hard drive (non-hot-plug).... 29 Hot-plug SCSI, SAS, or SATA hard drive cage... 30 Hot-plug SCSI backplane.... 30 Hot-plug SAS or SATA backplane... 31 Diskette drive..... 32 CD-ROM/DVD-ROM drive.... 32 Air baffle..... 33 Power supply..... 33 DIMM..... 34 Processor assembly.... 36 PCI expansion board.... 38 Fan assembly..... 39 Power button/LED board.... 39 Battery..... 40 System board..... 41

Required tools

You need the following items for some procedures:
T-15 Torx screwdriver HP Insight Diagnostics software ("HP Insight Diagnostics" on page 46)

Safety considerations

Before performing service procedures, review all the safety information.
Preventing electrostatic discharge
To prevent damaging the system, be aware of the precautions you need to follow when setting up the system or handling parts. A discharge of static electricity from a finger or other conductor may damage system boards or other static-sensitive devices. This type of damage may reduce the life expectancy of the device. To prevent electrostatic damage:
Avoid hand contact by transporting and storing products in static-safe containers. Keep electrostatic-sensitive parts in their containers until they arrive at static-free workstations. Place parts on a grounded surface before removing them from their containers. Avoid touching pins, leads, or circuitry. Always be properly grounded when touching a static-sensitive component or assembly.
Server warnings and cautions
Before installing a server, be sure that you understand the following warnings and cautions. WARNING: To reduce the risk of electric shock or damage to the equipment: Do not disable the power cord grounding plug. The grounding plug is an important safety feature. Plug the power cord into a grounded (earthed) electrical outlet that is easily accessible at all times. Unplug the power cord from the power supply to disconnect power to the equipment. Do not route the power cord where it can be walked on or pinched by items placed against it. Pay particular attention to the plug, electrical outlet, and the point where the cord extends from the server. WARNING: To reduce the risk of personal injury from hot surfaces, allow the drives and the internal system components to cool before touching them. WARNING: To reduce the risk of personal injury, electric shock, or damage to the equipment, remove the power cord to remove power from the server. The front panel Power On/Standby button does not completely shut off system power. Portions of the power supply and some internal circuitry remain active until AC power is removed. CAUTION: Do not operate the server for long periods with the access panel open or removed. Operating the server in this manner results in improper airflow and improper cooling that can lead to thermal damage. CAUTION: Protect the server from power fluctuations and temporary interruptions with a regulating uninterruptible power supply (UPS). This device protects the hardware from damage caused by power surges and voltage spikes and keeps the system in operation during a power failure.

NOTE: The SATA RAID feature supports up to two RAID volumes with up to two hard drives per RAID volume.
Non-hot-plug hard drive cage
This procedure applies to servers equipped with non-hot-plug drives only. If the server is equipped with hot-plug hard drives, refer to the hot-plug hard drive removal procedures ("Hot-plug SAS and SATA hard drives" on page 27, "Hot-plug SCSI hard drive" on page 27). To remove the component:

1. 2. 3. 4.

Power down the server (on page 25). Remove the bezel (on page 25). Remove the access panel ("Access panel" on page 26). Disconnect the power and data cables.
Remove the non-hot-plug hard drive cage.
Hard drive (non-hot-plug)
This procedure applies to non-hot-plug drives only. If the server is equipped with hot-plug hard drives, refer to the hot-plug hard drive removal procedures ("Hot-plug SAS and SATA hard drives" on page 27, "Hot-plug SCSI hard drive" on page 27). To remove the component:

1. 2. 3. 4. 5. 6.

Power down the server (on page 25). Remove the bezel (on page 25). Remove the access panel ("Access panel" on page 26). Disconnect the power and data cables. Remove the non-hot-plug hard drive cage. ("Non-hot-plug hard drive cage" on page 28) Remove the hard drive.
Hot-plug SCSI, SAS, or SATA hard drive cage

To remove the component:

Power down the server (on page 25). Remove the bezel (on page 25). Remove the access panel ("Access panel" on page 26). Remove all hot-plug hard drives ("Hot-plug SAS and SATA hard drives" on page 27, "Hot-plug SCSI hard drive" on page 27). Disconnect the power and data cables. Remove the hot-plug hard drive cage.
NOTE: If replacing only the hard drive cage, retain the backplane for use with the replacement hard drive cage. To replace the component, reverse the removal procedure.

Hot-plug SCSI backplane

Power down the server (on page 25). Remove the bezel (on page 25). Remove the access panel ("Access panel" on page 26). Remove all hot-plug hard drives ("Hot-plug SAS and SATA hard drives" on page 27, "Hot-plug SCSI hard drive" on page 27). Disconnect the power and data cables. Remove the hot-plug hard drive cage. ("Hot-plug SCSI, SAS, or SATA hard drive cage" on page 30)
Remove the SCSI backplane.
Hot-plug SAS or SATA backplane

1. 2. 3. 4. 5. 6. 7.

Power down the server (on page 25). Remove the bezel (on page 25). Remove the access panel ("Access panel" on page 26). Remove all hot-plug hard drives ("Hot-plug SAS and SATA hard drives" on page 27, "Hot-plug SCSI hard drive" on page 27). Disconnect the power and data cables. Remove the hot-plug hard drive cage ("Hot-plug SCSI, SAS, or SATA hard drive cage" on page 30). Remove the SAS or SATA backplane.

Diskette drive

Power down the server (on page 25). Remove the bezel (on page 25). Remove the access panel ("Access panel" on page 26). Disconnect the power and data cables. Remove the diskette drive.

CD-ROM/DVD-ROM drive

Remove the CD-ROM or DVD-ROM drive.

Air baffle

Power down the server (on page 25). Remove the bezel (on page 25). Remove the access panel ("Access panel" on page 26). Remove the air baffle.

Power supply

Removal and replacement procedures 33
Power down the server (on page 25). Remove the bezel (on page 25). Remove the access panel ("Access panel" on page 26). Remove the air baffle ("Air baffle" on page 33). Disconnect the power and signal cables. Remove the power supply.
You can expand server memory by installing PC2-4200 DDR2 SDRAM DIMMs with Advanced ECC. The system supports up to four DIMMs for a maximum of 8 GB. To remove the component:
Power down the server (on page 25). Remove the bezel (on page 25). Remove the access panel ("Access panel" on page 26).

Remove the DIMM.

To replace the component, reverse the removal procedure. IMPORTANT: DIMMs do not seat fully if turned the wrong way. Refer to "System board components (on page 51)" for DIMM slot locations and bank assignments. Observe the following guidelines when installing additional memory:
DIMMs installed in the server must be unbuffered PC2-4200 DDR2 DRAM, 64 bits wide, and ECC. If only a single DIMM is installed, it must be installed in slot 1A. All DIMMs installed must be the same speed. Single-channel mode: DIMMs installed in one channel only Dual-channel asymmetric mode: DIMMs installed in both channels but of unequal capacities per channel Dual-channel interleaved mode: DIMMs installed in both channels with equal channel capacities
BIOS detects the DIMM population and sets the system as follows:
The following table lists some, but not all, possible configurations. For best performance, HP recommends dual-channel interleaved mode configurations.
Channel A Slot MB 512 MB 1 GB 1 GB 1 GB 1 GB Channel A Slot 2 1 GB 1 GB Channel B Slot MB 1 GB 1 GB 1 GB Channel B Slot 4 1 GB 512 MB 1 GB 1 GB 2 GB 3 GB 4 GB Single-channel Dual-channel interleaved Single-channel Dual-channel interleaved Dual-channel asymmetric Dual-channel interleaved Total memory Mode

Channel A Slot GB 2 GB

Channel B Slot GB 2 GB

Total memory

6 GB 8 GB
Dual-channel interleaved Dual-channel interleaved

Processor assembly

IMPORTANT: To avoid damage to the processor and system board, only authorized technicians trained by HP should attempt to replace or install the processor in this server. To remove the component:
Power down the server (on page 25). Remove the bezel (on page 25). Remove the access panel ("Access panel" on page 26). Remove the air baffle ("Air baffle" on page 33). Disconnect the fan cable from the system board. Remove the heatsink fan assembly.

Power down the server (on page 25). Remove the bezel (on page 25). Remove the access panel ("Access panel" on page 26). Remove the battery.
To replace the component, reverse the removal procedure. IMPORTANT: After replacing the battery, the server is automatically configured with the default settings. The user can update these settings using RBSU. For more information about battery replacement or proper disposal, contact an authorized reseller or an authorized service provider.

System board

1. 2. 3. 4. 5. 6. 7. 8. 9.
Power down the server (on page 25). Remove the bezel (on page 25). Remove the access panel ("Access panel" on page 26). Remove the air baffle ("Air baffle" on page 33). Remove the DIMMs ("DIMM" on page 34). Remove the processor. Remove the PCI expansion board. Remove the fan assembly ("Fan assembly" on page 39). Disconnect all cabling.
10. Remove the system board.
To replace the component, reverse the removal procedure. After you replace the system board, you must re-enter the server serial number and the product ID.
During the server startup sequence, press the F9 key to access RBSU. Select the Advanced Options menu. Select Serial Number. The following warning is displayed: Warning: The serial number should ONLY be modified by qualified service personnel. This value should always match the serial number located on the chassis.

4. 5. 6.

Press the Enter key to clear the warning. Enter the serial number. Select Product ID. The following warning is displayed. Warning: The Product ID should ONLY be modified by qualified service personnel. This value should always match the Product ID located on the chassis.

7. 8. 9.

Enter the product ID and press the Enter key. Press the Esc key to close the menu. Press the Esc key to exit RBSU.
10. Press the F10 key to confirm exiting RBSU. The server will automatically reboot.

Cabling

Hot-plug SCSI hard drive cabling.... 43 Non-hot-plug SCSI hard drive cabling... 44 Hot-plug SATA hard drive cabling... 44 Non-hot-plug SATA hard drive cabling.... 45 SAS hard drive cabling..... 45

Hot-plug SCSI hard drive cabling

Item 1 2

Description Power cable SCSI cable
Non-hot-plug SCSI hard drive cabling
Description SCSI cable Power cable
Hot-plug SATA hard drive cabling
Description Power cable SATA cable
Non-hot-plug SATA hard drive cabling
Description SATA cable Power cable

SAS hard drive cabling

Description Power cable SAS cable

Diagnostic tools

Survey Utility..... 46 Array Diagnostic Utility..... 46 HP Insight Diagnostics..... 46 Integrated Management Log.... 47 ROMPaq disaster recovery..... 47

Survey Utility

Survey Utility, a feature within HP Insight Diagnostics (on page 46), gathers critical hardware and software information on ProLiant servers. This utility supports operating systems that may not be supported by the server. For operating systems supported by the server, refer to the HP website (http://www.hp.com/go/supportos). If a significant change occurs between data-gathering intervals, the Survey Utility marks the previous information and overwrites the Survey text files to reflect the latest changes in the configuration. Survey Utility is installed with every SmartStart-assisted installation or can be installed through the HP PSP. NOTE: SmartStart version 7.5 and later provides the memory spare part numbers for the server.

Array Diagnostic Utility

ADU is a tool that collects information about array controllers and generates a list of detected problems. ADU can be accessed from the SmartStart CD or downloaded from the HP website (http://www.hp.com).

HP Insight Diagnostics

HP Insight Diagnostics is a proactive server management tool, available in both offline and online versions, that provides diagnostics and troubleshooting capabilities to assist IT administrators who verify server installations, troubleshoot problems, and perform repair validation. HP Insight Diagnostics Offline Edition performs various in-depth system and component testing while the OS is not running. To run this utility, launch the SmartStart CD. HP Insight Diagnostics Online Edition is a web-based application that captures system configuration and other related data needed for effective server management. Available in Microsoft Windows and Linux versions, the utility helps to ensure proper system operation. For more information or to download the utility, refer to the HP website (http://www.hp.com/servers/diags).

Diagnostic tools 46

Integrated Management Log
The IML records hundreds of events and stores them in an easy-to-view form. The IML timestamps each event with 1-minute granularity. You can view recorded events in the IML in several ways, including the following:

From within HP SIM From within Survey Utility (on page 46) From within operating system-specific IML viewers
For NetWare: IML Viewer For Windows: IML Viewer For Linux: IML Viewer Application
From within the iLO 2 user interface From within HP Insight Diagnostics (on page 46)
For more information, refer to the Management CD in the HP ProLiant Essentials Foundation Pack.

ROMPaq disaster recovery

If the current version of the ROM is corrupt, perform ROMPaq disaster recovery procedures:
Create a ROMPaq diskette using the Autorun Menu on the SmartStart CD. Power down the server (on page 25). Insert the ROMPaq diskette. Power up the server.
a. The server generates one long beep and two short beeps to indicate that you are in disaster
recovery mode. If the diskette is not in place, the system continues to beep until a valid ROMPaq diskette is inserted.
b. The ROMPaq diskette flashes the system ROM image. If successful, a sequence of ascending
audible beeps is generated. If unsuccessful, a sequence of descending audible beeps is generated and you need to repeat the disaster recovery process.

5. 6. 7.

Power down the server (on page 25). Remove the ROMPaq diskette. Power up the server.

Diagnostic tools 47

Component identification
Front panel components.... 48 Front panel LEDs and buttons.... 49 Rear panel components..... 50 Rear panel LEDs..... 50 System board components.... 51 System board LEDs.... 53 System LEDs and internal health LED combinations... 54 SCSI IDs.... 55 Hot-plug SCSI hard drive LEDs..... 55 Hot-plug SCSI hard drive LED combinations.... 56 Hot-plug SAS and SATA device numbers.... 57 SAS and SATA hard drive LEDs.... 57 SAS and SATA hard drive LED combinations... 57 Fans...... 58

Front panel components

Item 5
Description Media bays (bezel blanks) Power On/Standby button Hard drive bays USB connectors (2) Bezel lock
Component identification 48

Item 6

Description CD-ROM/DVD-ROM drive
Front panel LEDs and buttons

Item 3

Description CD-ROM/DVD-ROM drive ejector button Power On/Standby button System power LED
Status N/A N/A Green = System has AC power and is functioning. Amber = System has AC power and is in standby mode. Off = System has no AC power.

Hard drive activity LED (for non-hot-plug) NIC link/activity LED
Green = Hard drives are properly connected and functioning Off = No hard drive activity Green = Linked to network Flashing green = Linked with activity on the network Off = No network connection
Internal system health LED
Green = Normal (system on) Amber = System health is degraded. Red = System health is critical. Off = Normal (system off)
CD-ROM/DVD-ROM drive indicator LED
On = Activity Off = No activity
Component identification 49

Rear panel components

Item 9
Description Power cord connector Mouse connector Keyboard connector Serial connector Video connector USB connectors (2) RJ-45 Ethernet connector RJ-45 connector (iLO 2) Parallel connector

Rear panel LEDs

Component identification 50
Description NIC link LED NIC activity LED
Status On = Link Off = No link Flashing = Activity Off = No activity

System board components

Items 19
Description Processor power connector System power connector DIMM slot 4 (Channel B) DIMM slot 3 (Channel B) DIMM slot 2 (Channel A) DIMM slot 1 (Channel A) IDE connector Front USB connector USB connector SATA connector System maintenance switch USB tape drive connector Diskette drive connector Processor fan connector System battery Slot 1, PCI Express x1 Slot 2, 64-bit/100-MHz PCI-X Slot 3, 64-bit/100-MHz PCI-X Slot 4, PCI Express x4*
Component identification 51

Items 20

Description System fan connector
* x8 PCI Express cards are supported, but will run at x4 speeds.
System maintenance switch
Position S1 Default Off Function Off = iLO 2 security is enabled On = iLO 2 security is disabled S2 Off Off = System configuration can be changed On = System configuration is locked S3 S4 S5 Off Off Off Reserved Reserved Off = No function On = Clears power-on password and administrator password S6 Off Off = Normal On = ROM treats system configuration as invalid S7 Off Reserved

Reserved

When the system maintenance switch position 6 is set to the On position, the system is prepared to erase all system configuration settings from both CMOS and NVRAM. CAUTION: Clearing CMOS and/or NVRAM deletes configuration information. Be sure to properly configure the server or data loss could occur. For information on emergency ROM backup recovery, refer to ROMPaq disaster recovery (on page 47).
Component identification 52

Red Red Red

System temperature has exceeded OS cautionary level or critical hardware level. A required fan has failed.
Component identification 54

SCSI IDs

Hot-plug SCSI hard drive LEDs

Item 1

Description Activity status
Status On = Drive activity Flashing = High activity on the drive or drive is being configured as part of an array. Off = No drive activity

Online status

On = Drive is part of an array and is currently working. Flashing = Drive is actively online. Off = Drive is offline.
Component identification 55

Description Fault status

Status On = Drive failure Flashing = Fault-process activity Off = No fault-process activity
Hot-plug SCSI hard drive LED combinations
Activity LED Online LED Fault LED Flashing Off Interpretation A predictive failure alert has been received for this drive. Replace the drive as soon as possible. The drive is online and is configured as part of an array. If the array is configured for fault tolerance and all other drives in the array are online, and a predictive failure alert is received or a drive capacity upgrade is in progress, you may replace the drive online. Off Do not remove the drive. Removing a drive may terminate the current operation and cause data loss. The drive is rebuilding or undergoing capacity expansion. On Off Off Do not remove the drive. The drive is being accessed, but (1) it is not configured as part of an array; (2) it is a replacement drive and rebuild has not yet started; or (3) it is spinning up during the POST sequence. Flashing Flashing Flashing Do not remove the drive. Removing a drive may cause data loss in non-fault-tolerant configurations. One or more of the following conditions may exist: Off Off On The drive is part of an array being selected by an array configuration utility Drive Identification has been selected in HP SIM The drive firmware is being updated On, off, or On or off flashing On, off, or On flashing

On or flashing

Flashing
The drive has been placed offline due to hard disk drive failure or subsystem communication failure. You may need to replace the drive. One or more of the following conditions may exist: The drive is not configured as part of an array The drive is configured as part of an array, but it is a replacement drive that is not being accessed or being rebuilt yet The drive is configured as an online spare

If the drive is connected to an array controller, you may replace the drive online.
Component identification 56
Hot-plug SAS and SATA device numbers
SAS and SATA hard drive LEDs
Description Fault/UID LED (amber/blue) Online LED (green)
SAS and SATA hard drive LED combinations
Online/activity LED Fault/UID LED (green) (amber/blue) On, off, or flashing Alternating amber and blue Interpretation The drive has failed, or a predictive failure alert has been received for this drive; it also has been selected by a management application.
Component identification 57
Online/activity LED Fault/UID LED (green) (amber/blue) On, off, or flashing Steadily blue On On Flashing regularly (1 Hz) Amber, flashing regularly (1 Hz) Off Amber, flashing regularly (1 Hz)
Interpretation The drive is operating normally, and it has been selected by a management application. A predictive failure alert has been received for this drive. Replace the drive as soon as possible. The drive is online, but it is not active currently. Do not remove the drive. Removing a drive may terminate the current operation and cause data loss. The drive is part of an array that is undergoing capacity expansion or stripe migration, but a predictive failure alert has been received for this drive. To minimize the risk of data loss, do not replace the drive until the expansion or migration is complete.
Flashing regularly (1 Hz)
Do not remove the drive. Removing a drive may terminate the current operation and cause data loss. The drive is rebuilding, or it is part of an array that is undergoing capacity expansion or stripe migration.
Flashing irregularly Amber, flashing regularly (1 Hz) Flashing irregularly Off Off Steadily amber
The drive is active, but a predictive failure alert has been received for this drive. Replace the drive as soon as possible. The drive is active, and it is operating normally. A critical fault condition has been identified for this drive, and the controller has placed it offline. Replace the drive as soon as possible. A predictive failure alert has been received for this drive. Replace the drive as soon as possible. The drive is offline, a spare, or not configured as part of an array.

Off Off

Amber, flashing regularly (1 Hz) Off

Description System fan

Component identification 58

Item 2

Description Processor fan
Component identification 59

Specifications

Hard drive specifications
Item Capacity 36.4-GB Ultra320 SCSI drive 36,419.6 MB 80-GB SATA drive 80,000 MB
Item Height Width Interface Transfer rate Rotational speed Logical blocks Operating temperature
36.4-GB Ultra320 SCSI drive 1.0 in (One-third height) 4.0 in Ultra320 SCSI 320 MB/sec 15,000 rpm
80-GB SATA drive 1.028 in 4.0 in Serial ATA 1.5 GB/s 7,200 rpm 512 156,301,488 5C to 55C (41F to 131F)
Bytes per sector 512 71,132,000 10C to 35C (50F to 95F)
DVD-ROM drive specifications
Specification Disk formats Value DVD (single and double layer), DVD-5, DVD-9, DVD-10, DVD-R, CD-ROM Mode 1 & 2, CD-DA, CD-XA (Mode 2, Form 1 & 2), CD-I (Mode 2, Form 1 & 2), CD-I ready, CD-Bridge, CD-R, PhotoCD (single and multi-session) 4.7 GB (DVD-5), 8.5 GB (DVD-9), 9.4 GB (DVD10), 550 Mb (Mode 1, 12 cm), 640 Mb (Mode 2, 12 cm), 180 Mb (8 cm) 2352 bytes (mode 0) 2352, 2340, 2336, 2048 bytes (mode 1) 2352, 2340, 2336, 2048 bytes (mode 2) 2048 bytes (DVD) 12.7 mm (0.50 in) 132.08 mm (5.20 in) 132.08 mm (5.20 in) 0.34 kg (0.75 lb) 4463 - 10,800 KB/s (8X CAV DVD mode), 150 KB/s (sustained 1X CD-ROM), KB/s (24X CAV CD-ROM) 16.6 MB/s with DMA support

Capacity Block size

Dimensions Height Depth Width Weight Data transfer rate Sustained Burst Access times (typical) Full stroke Random Diameter Thickness Track pitch Cache/buffer Startup time <200 ms CD <300 ms DVD <110 ms CD <180 ms DVD 12 cm, 8 cm (4.70 in, 3.15 in) 1.2 mm (0.05 in) 0.74 m (3.15 10-7 in) DVD-ROM 1.6 m (6.3 10-7 in) CD-ROM 128 KB < 10 s
Specification Stop time Laser parameters Type Wave length Divergence angle Output power Operating conditions Temperature Humidity
Value < 5 s (single); < 30 s (multisession) Semiconductor laser GaAs nm 53.5 1.5 0.14 mW
5C to 45C (41F to 118F) 5% to 90%
Acronyms and abbreviations
Automatic Server Recovery

double data rate

dual inline memory module
error checking and correcting

Integrated Lights-Out 2

network interface controller

non-volatile memory

peripheral component interconnect extended

Power-On Self Test

processor power module

ProLiant Support Pack

redundant array of inexpensive (or independent) disks

ROM-Based Setup Utility

serial attached SCSI

serial ATA

small computer system interface

synchronous dynamic RAM

Systems Insight Manager

unit identification

AC power supply 33, 50 access panel 26 ADU (Array Diagnostic Utility) 46 Array Diagnostic Utility (ADU) 46 ASR (Automatic Server Recovery) 65 Automatic Server Recovery (ASR) 65
hard drive LEDs 55, 56, 57 hard drives 29, 57 hard drives, determining status of 57 HP Insight Diagnostics 46
illustrated parts catalog 15 iLO (Integrated Lights-Out) 52 IML (Integrated Management Log) 47 Insight Diagnostics 46 Integrated Management Log (IML) 47 internal health LED 54
battery 40, 41 buttons 48
cables 43 cabling 43, 44, 45 CD-ROM drive 32, 62 component identification 48, 57 components 48 connectors 48, 57 CSR (customer self repair) 5 customer self repair (CSR) 5
LEDs 48 LEDs, hard drive 57
management tools 46 memory slots 51
DC power supply 50, 51 diagnostic tools 46 diagnostics utility 46 DIMMs 34 diskette drive 32 DVD-ROM drive 32, 63
network connector LEDs 50 NIC LEDs 50
part numbers 15 preparation procedures 25 ProLiant Support Pack (PSP) 65
electrostatic discharge 23
rear panel buttons 50 rear panel LEDs 50 removal and replacement procedures 23 removing server from rack 25 RJ-45 network connector LEDs 50
fans 39 features 48 front panel buttons 50 front panel components 48, 51 front panel LEDs 49

Index 67

safety considerations 23 SAS backplane 31 SAS cabling 45 SAS drives 57 SAS hard drive 27 SAS hard drive LEDs 57 SAS-SATA hard drive cage 31 SATA backplane 31 SATA cabling 44, 45 SATA hard drive 57 SATA hard drive LEDs 57 SCSI cabling 43, 44 SCSI hard drive 27 SCSI IDs 55 serial number 41 specifications 60, 61, 62, 63 specifications, environmental 60 specifications, server 60 static electricity 23 Survey Utility 46 system board components 51 system board LEDs 53 system maintenance switch 52

UID LEDs 48

warnings 24

Index 68