owners manual

hp digital projectors xb31 & sb21

English version 13.05.02

owners manual for the hp digital projector xb31 and sb21

table of contents

safety
Personal Safety.. 4 Protecting Your Projector. 4

introduction

Projector Features... 5 Package Contents... 6 Projector Overview.. 7 Control Panel.. 8 Back Panel Features.. 8 Remote Control With Mouse & Laser Pointer.. 9

installation

Connecting the hp digital projector xb31 to a computer.. 10 Connecting the hp digital projector xb31 to other signal sources.. 11 Connecting the hp digital projector sb21 to a computer.. 12 Connecting the hp digital projector sb21 to other signal sources.. 13

operation

Turning the projector ON and OFF.. 14 Turning the projector ON.. 14 Turning the projector OFF.. 14 Adjusting the projected image. 16 Adjusting the display angle.. 16 Adjusting the hp xb31 zoom and focus. 18 Projection image size (diagonal). 18 Adjusting the hp sb21 focus. 19 Projected image size (diagonal). 19

user controls

Control panel & remote control.. 20 Control Panel.. 20 On-Screen Display Menus.. 21 How to operate.. 21 Language Menu.. 22 All Images Menu.. 23 Audio Menu.. 24 Computer Image Menu.. 25 Management Menu.. 26 Video Image Menu.. 27 Remote control.. 28

appendices

Troubleshooting... 30 Changing the lamp module.. 32 hp xb31 specifications.. 34 hp xb31 compatibility modes.. 35 hp sb21 specifications.. 36 hp sb21 compatibility modes.. 37 Regulatory information.. 38 Warranty & Support.. 39

Personal Safety

CAUTION! CAUTION! CAUTION! CAUTION! PREVENT EYE INJURY. Do not look into the projectors lens when the lamp is on. Do not point the remote controls laser light at your own, or anyone elses, eyes. AVOID BURN HAZARD. The lamp gets hot during normal operation. Allow it to cool down for 30 minutes before changing lamp! CUT HAZARD. If the bulb is broken, use caution while removing the bulb assembly to avoid injury.

xb31 sb21

PREVENT ELECTRICAL SHOCK. Do not expose to rain or moisture. Do not open or disassemble projector, except as instructed by this manual. WARNING! MERCURY HAZARD. This projectors bulb contains a small amount of mercury. If the lamp breaks, adequately ventilate the area where the breakage occurred. The projector bulb may require special handling and disposal at end-of-life.
Protecting Your Projector
Do: Connect projectors cables before turning the projector ON. Allow the projector to complete its cooling cycle after turning the Power OFF (refer
to page 14). CAUTION: Unplugging the projector while the fan is running reduces lamp life. Turn off and unplug the projector before cleaning. Use a soft, dry cloth to clean the projectors housing. Use camera-lens cleaning materials and procedures to clean the lens. Disconnect the power plug from AC outlet if the projector isnt being used for an extended period of time. Allow the projector to cool-down for at least 30 minutes before changing the lamp. Follow instructions provided with replacement lamp or in this manual. Lamp failure may produce a loud popping sound. This is normal and should not cause concern. The projector will not turn back on until the lamp module has been replaced. Reset the Lamp Hour monitor from the On Screen Display Management menu tab after replacing the lamp module (refer to page 26). Refer to page 39 for warranty and support information.
Dont: Unplug the projector while the fan is running. Block the projectors ventilation openings. Use abrasive cleaners, waxes, or solvents for your cleaning. Clean the lens with detergent. Use in very hot, cold, or humid environments. Use or store in dusty or dirty conditions. Use in a strong magnetic field. Place the projector in direct sunlight. 4

Projector Features

The hp digital projector xb31 is an XGA single chip 0.7 DLPTM projector with these outstanding features: True XGA, 1024 x 768 addressable pixels 1500 comparable lumens Approximately 3.5 lbs (1.6 kg) compact design Single chip DLPTM technology SXGA compression and VGA, SVGA re-sizing 156 watts (W) user-replaceable P-VIP lamp module NTSC3.58/NTSC4.43/PAL/PAL-M/PAL-N/SECAM and HDTV compatible Full function remote with mouse control and laser pointer High-tech VESA M1-DA connection for digital and analog video connectivity High definition TV (HDTV) compatibility User-friendly multilingual On Screen Display (OSD) menu Advanced electronic keystone correction User-friendly control panel Built-in 2 watt audio speaker Carrying case and cables included (refer to page 6) The hp digital projector sb21 is an SVGA single chip 0.55 DLPTM projector with these outstanding features: True SVGA, 800 x 600 addressable pixels 1000 comparable lumens Approximately 2.2 lbs (1 kg) compact design Single chip DLPTM technology XGA compression and VGA re-sizing 132 watts (W) user-replaceable P-VIP lamp module NTSC3.58/NTSC4.43/PAL/PAL-M/PAL-N/SECAM and HDTV compatible Full function remote with mouse control and laser pointer High-tech VESA M1-DA connection for digital and analog video connectivity High definition TV (HDTV) compatibility User-friendly multilingual On Screen Display (OSD) menu Advanced electronic keystone correction User-friendly control panel Carrying case and cables included (refer to page 6)

Package Contents

The hp digital projectors come with the following items. Please check to make sure your unit is complete. If anything is missing contact your dealer immediately.

Projector with lens cap

Carrying Case

Composite Video Cable

2.5 mm Mini Phone Jack for Composite Video Cable

Power Cord

S-video Cable
USB Mini-B 5-pin to S-video Input Cable
Mi-A to VGA and USB Cable

Battery x2

Audio Cable
Remote Control with Mouse Function and Laser Pointer
Owners Manual on Compact Disc (CD ROM)

Quick Start Card

Warranty/Support Information Data Sheet

Projector Overview

7 1. 2. 3. 4. 5. Control Panel Power Connector I/O Connection Ports Zoom Ring Focus Ring 8 6. Remote Control Receivers (front & back) 7. Elevation Button 8. Elevation Foot 9. Lens Cap
5. Remote Control Receivers (front & back) 6. Elevation Button 7. Elevation Foot 8. Lens Cap 7

1. 2. 3. 4.

Control Panel Power Connector I/O Connection Ports Focus Ring

Control Panel

1. Power (ON/OFF) Button 2. Lamp Warning Indicator Light 3. Temperature Warning Indicator Light 4. Source Button 5. Menu (ON/OFF) Button 6. Auto Image Button 7. Four Directional Select Buttons

Back Panel Features

1. KensingtonTM Lock Hole 2. Composite Video Input 3. Audio Input 4. S-Video Input 5. VESA M1-DA Analog RGB / Digital / HDTV / Component Video / USB Mouse Input
1 1. KensingtonTM Lock Hole 2. Composite Video Input 3. S-Video Input 4
4. Power Connector 5. VESA M1-DA Analog RGB / Digital / HDTV / Component Video / USB Mouse Input 8
Remote Control With Mouse & Laser Pointer
Transmit Indicator Light Multi-Directional Selector Projector Power Page Up Laser Pointer Volume ( + / - ) Source Freeze Right Mouse Button Hide Image Page Down Keystone Correction Zoom In / Zoom Out Menu

Left Mouse Button

CAUTION! PREVENT EYE INJURY. Do not point the remote controls laserlight at anyones eyes. NOTE: Connect the USB cable when using the remote control mouse features.
Connecting the hp digital projector xb31 to a computer
Connect the power cord to the projector and a power outlet.
Connect the black end of the video cable to the projector.
Connect the blue end of the video cable to the PC; optionally, to have the remote control function as a mouse, connect the USB connector to the PC.
CAUTION! Unplugging the projector while the fan is running may reduce lamp life. Start the projector; after a 30second warm-up it will search for a video signal. If no video signal is found, you may need to set up the PC to send a video signal out the video port. NOTE: For best performance, configure the display mode of your computers graphic card to 1024768 resolution. Ensure the timing of the display mode is compatible with the projector. Refer to the hp xb31 compatibility modes section on page 35.

Connecting the hp digital projector xb31 to other signal sources

Antenna

Digital Tuner Output

Video Output

S-video Output

1. 2. 3. 4. 5.

Power Cord Composite Video Cable Audio Cable S-video Cable M1-A to HDTV / Component and USB Cable (optional accessory)
CAUTION! Unplugging the projector while the fan is running may reduce lamp life. NOTE: For best performance, configure the display mode of your computers graphic card to 1024768 resolution. Ensure the timing of the display mode is compatible with the projector. Refer to the hp xb31 compatibility modes section on page 35.
Connecting the hp digital projector sb21 to a computer
Start the projector; after a 30second warm-up it will search for a video signal.
If no video signal is found, you may need to set up the PC to send a video signal out the video port.
CAUTION! Unplugging the projector while the fan is running may reduce lamp life. NOTE: For best performance, configure the display mode of your computers graphic card to 800600 resolution. Ensure the timing of the display mode is compatible with the projector. Refer to the hp sb21 compatibility modes section on page 37.
Connecting the hp digital projector sb21 to other signal sources
Power Cord Composite Video Cable S-video Cable M1-A to HDTV / Component and USB Cable (optional accessory)
Turning the projector ON and OFF

Turning the projector ON

1. Remove the lens cap by squeezing the caps tabs and pulling forward. 2. Ensure that the power cord and signal cables are securely connected to the projector and the signal source (computer, notebook, video player, etc.). 3. Turn the projector ON by pressing the Power ON/OFF button on the control panel. The cooling fan turns on. The hp start-up screen will be displayed for 30 seconds and the blue Power Indicator Light will light up. 4. Turn on your signal source. The projector will detect your source automatically. If the screen displays Waiting for Signal make sure the signal cables are securely connected. If multiple signal sources are connected, use the Source button on the Remote Control or Control Panel to switch to the desired input. When the Lamp Indicator Light is ON, replace the lamp. When the Temp Indicator Light is ON, it indicates that the projector has overheated. The projectors lamp will automatically turn OFF. Press the Power ON/OFF button and allow the projector to complete its cooldown cycle. Then you can restart the projector and continue your presentation. If the problem persists, contact hp support: (www.hp.com/support/digitalprojectors). When the Temp Indicator Light FLASHES, the projector has detected a failure in the cooling system. Press the Power ON/OFF button and allow the projector to complete its cool-down cycle. Contact hp support: (www.hp.com/support/digitalprojectors).

Turning the projector OFF
1. Press the Power ON/OFF button. The projector lamp will turn off and the cooling fan will run for the duration of the cool-down cycle. The blue Power Indicator Light will blink until the cool-down cycle is complete. The blue Power Indicator Light will then turn OFF and the cooling fan will stop. 2. Disconnect the power cord from the electrical outlet and the projector.
Turning the projector ON and OFF (continued)
CAUTION! Unplugging the projector while the fan is running may reduce lamp life. NOTE: Turn on the projector before turning on the signal source. NOTE: When the blue Power Indicator Light is blinking the unit cannot be turned ON or OFF. The projector will not respond to any user input. NOTE: The model shown is the hp xb31.
Adjusting the projected image
Adjusting the display angle
To raise the projector display angle: 1. Press and hold the elevation button. , then release the button 2. Raise the projector to the desired display angle to lock the elevation foot into position. To lower the projector display angle: 1. Press and hold the elevation button. 2. Lower the projector, then release the button to lock the elevation foot into its retracted position. Leveling the Projector Use the rear elevation foot adjustment screen. for aligning the projector to the
Adjusting the display angle (continued)

Elevation Button

Elevation Foot
Adjusting the hp xb31 zoom and focus
Zoom is adjusted by rotating the zoom ring. Rotate the focus ring until the image is clear. The projector will focus at distances from 1.14 m to 12 m (3.7 feet to 39.4 feet). Zoom Ring Focus Ring
Projected image size (diagonal)
Calculating the Projected Image Size The screen diagonal dimension can be approximated by using one of these formulas: Zoomed out 7.5*Distance(ft.)=Diagonal(in.) 0.625*Distance(m)=Diagonal(m) or Zoomed in 6.25*Distance(ft.)=Diagonal(in.) 0.52*Distance(m)=Diagonal(m) For example: If your xb31 is 10 feet from the screen, the approximate zoomed out screen diagonal dimension will be 7.5*10 = 75 inches.

Focal Distance

Screen (Diagonal) Screen Size Focal Distance
Max. Min. Max.(WxH) Min.(WxH)

22.4x16.8 18.4x13.8 3.7

78.4x58.8 65.6x49.2 13.1

98.4x73.8 82.4x61.8 16.4

157.6x118.2 131.2x98.4 26.2
196.8x147.6 164.0x123.0 32.8
236.0x177.0 196.8x147.6 39.4
NOTE: This graph is for users reference only.
Adjusting the hp sb21 focus
Rotate the focus ring until the image is clear. The projector will focus at distances from 1.0 m to 12 m (3.3 feet to 39.4 feet).

Focus Ring

Calculating the Projected Image Size The screen diagonal dimension can be approximated by using one of these formulas: 7.5*Distance(ft.)=Diagonal(in.) 0.625*Distance(m)=Diagonal(m) For example: If your sb21 is 10 feet from the screen, the approximate screen diagonal dimension will be 7.5*10 = 75 inches.
Screen (Diagonal) Screen Size (wxh) Focal Distance

25 20.0x15.0 3.3

98 78.4x58.6 13.1

123 98.4x73.8 16.4

197 157.6x118.2 26.2

246 196.8x147.6 32.8

295 236.2x177.2 39.4
Control panel & remote control
The projectors functions are controlled via the Control Panel and the Remote Control, and the On Screen Display (OSD).
Power ON/OFF Button Refer to Turning the Projector ON and OFF on pages 14-15. Source Button Press the Source button to choose the appropriate signal source - RGB, DVI-Digital, DVI-Analog, S-Video, Composite, Component and HDTV sources. NOTE: This button will not function when the OSD menu is displayed. Auto Image Button Press the Auto Image button to automatically synchronize the projector to the input source. NOTE: This button will not function when the OSD menu is displayed.

On Screen Display Menus

The projector has multilingual On Screen Display (OSD) menus that allow you to make image adjustments by changing a variety of settings.

How to operate

Press the Menu button on the Remote Control or Control Panel to open the OSD. buttons to display the contents of the desired menu tab. Press the The selected tabs title will change from dark blue to white. Press the buttons to select the desired menu item. When an item is selected, the color of the item will change from light blue text on a dark blue background to white text on an orange background. Adjust the settings with the Press the Press the tabs or Press the Menu button. The OSD menu will close and the projector will automatically save the new settings. buttons. button until no menu items are highlighted. Then either buttons to display the contents of additional Menu

Language Menu

To open the Language menu: 1. Press the Menu button to open the On Screen Display (OSD) menus. 2. Use the 3. Press the or buttons to open the Language menu tab. buttons to select the desired language.
4. Press the Menu button to finalize the selection.
NOTE: The hp sb21s OSD does not include an Audio menu.

All Images Menu

To open the All Images menu: 1. Press the Menu button to open the On Screen Display (OSD) menus. 2. Use the 3. Press the Brightness Press the button to darken the image. Press the button to lighten the image. Contrast The contrast controls the degree of difference between the lightest and darkest parts of the picture. Press the button to decrease the contrast. Press the button to increase the contrast. Image Optimization Image Optimization can be incrementally adjusted between 0 and 10. Click on the slider bar to adjust. Setting 10 will maximize brightness and contrast Setting 0 will maximize color reproduction quality Color Temp With the higher temperature, the image looks colder. With the lower temperature, the image looks warmer. Press the or button to decrease or increase the color temperature. Keystone (Keystone Correction) Corrects image distortion caused by the projectors elevation angle. (16 degrees) Zoom Press the button to magnify an image up to 9 times. Press the button to reduce the image magnification. Aspect Ratio Aspect ratio type can be adjusted to 4:3 or 16:9. Reset this menu Choose Yes to return the display parameters on this menu to their factory default settings. 23 or buttons to open the All Images menu tab. buttons to select one of the following items:

Audio Menu

To open the Audio menu: 1. Press the Menu button to open the On Screen Display (OSD) menus. 2. Use the 3. Press the Volume Press the Press the Treble Press the Press the Bass Press the Press the Mute or buttons to open the Audio menu tab. buttons to select one of the following items: button to decrease the volume. button to increase the volume.
The treble setting controls the higher frequencies of your audio source. button to decrease the treble. button to increase the treble.
The Bass setting controls the lower frequencies of your audio source. button to decrease the bass. button to increase the bass.

Choose the left icon to mute the projectors speaker. Choose the right icon to activate the projectors speaker. Reset this menu Choose Yes to return the audio parameters of this menu to their factory default settings.
NOTE: This message is displayed when an image source other than computer VGA is selected via the Source button or the auto detection function. The Computer Image parameters cannot be adjusted when this message is displayed.

Computer Image Menu

To open the Computer Image menu: 1. Press the Menu button to open the On Screen Display (OSD) menus. 2. Use the 3. Press the Auto Image The projector automatically adjusts frequency, tracking, horizontal and vertical position. With most signal sources, Auto Image provides the best results. Frequency Frequency is the display data frequency. This should match the frequency of your computers graphic card. When you experience a vertical flickering bar, use this function to make adjustments. Tracking Choose Tracking to synchronize the signal timing of the display with that of the graphic card. When you experience an unstable or flickering image, use this function to correct it. Horizontal Position Press the Press the Press the Press the button to move the image left. button to move the image right. button to move the image up. button to move the image down. or buttons to open the Computer Image menu tab. buttons to select one of the following items:

Vertical Position

Reset this menu Choose Yes to return the display parameters of this menu to their factory default settings. 25

Management Menu

To open the Management menu: 1. Press the Menu button to open the On Screen Display (OSD) menus. 2. Use the or buttons to open the Management menu tab. buttons to select one of the following items:
3. Press the Menu Location
Choose the Menu location on the display screen. Projection Direction Front-Desktop: The image used in standard desktop operation. Rear-Desktop: The image is reversed for projection from behind a translucent screen. Front-Ceiling: The image is turned upside down for ceilingmounted projection.
Rear-Ceiling: The image is reversed and turned upside down for ceiling-mounted projection from behind a translucent screen. Signal Type Select the desired signal type - RGB, YCrCb and YPrPb sources. Lamp Hour Displays the lamps elapsed operating time (in hours). Reset Lamp Hours Reset the lamp setting only when the lamp is replaced. Reset this Menu Choose Yes to return the display parameters (except for Lamp Hours) on this menu to their factory default settings. Machine Reset Choose Yes to return the display parameters (except for Lamp Hours) on ALL menus to their factory default settings. 26
NOTE: This message is displayed when these settings cannot be adjusted for the image source selected via the Source button or the auto detection function (i.e. computer VGA or 480p). The Video Image parameters cannot be adjusted when this message is displayed.

Video Image Menu

To open the Video Image menu: 1. Press the Menu button to open the On Screen Display (OSD) menus. 2. Use the or buttons to open the Video Image menu tab. buttons to select one of the following items:
3. Press the Color Saturation
The color setting adjusts a video image from black and white to fully saturated color. Press the Press the Sharpness Press the Press the Tint Press the button to decrease the amount of color in the image. button to increase the amount of color in the image.
Adjusting the sharpness of the image. button to decrease the sharpness. button to increase the sharpness.
The tint adjusts the color balance of red and green. button to increase the amount of green in the image.
Press the button to increase the amount of red in the image. Reset this menu Choose Yes to return the display parameters of this menu to their factory default settings.

Remote control

Power ON/OFF Button Refer to Turning the Projector ON and OFF on pages 14 and 15. Hide Button Press the Hide button to project a black screen. Press the Hide button again to view the image. Multi-Directional Selector Controller * This feature can be used as a mouse to control direction. Right Mouse Button * Page Up (up) and Page Down (dn) Buttons * Press the up or dn buttons to page up or page down, respectively. Laser Pointer Button Press and hold the Laser Pointer button to activate the laser pointer. Menu Button Press the Menu button to open the On Screen Display (OSD) menu and press the buttons to select the desired menu tabs. Press the button to go into the desired options sub-menu. Press the button to return to main menu. To exit the OSD mode, press the Menu button again. The projector will automatically save any changes you have made. Source Button Press the Source button to choose RGB, DVI-Digital, DVI-Analog, S-Video, Composite, Component and HDTV sources. Freeze Button Press the Freeze button to freeze the screen image. Volume Up (+) and Volume Down (-) Buttons (hp xb31 only) Press the Volume + or Volume - buttons to increase or decrease speaker volume. Keystone Correction Buttons Press the Keystone Correction buttons to adjust image distortion caused by tilting the projector. (16 degrees) NOTE: Keystone Correction can cause distortion of text and graphics. Zoom In and Zoom Out Buttons When you press the Zoom buttons, the zoom icon appears on the screen. Press the or buttons to zoom in or zoom out. The image can be magnified up to 9 times. Left Mouse Button * The left mouse button is located on the back of the remote control.

* To enable this function, the projector must be connected to the computer via the USB cable.

Troubleshooting

Consult this section if you are experiencing trouble with your projector. If the problem persists, please contact hp. Refer to Warranty and Support Information on page 39. Problem: No image is projected on screen. Verify that the projectors power cord is plugged in and properly connected. Verify that all cables are properly installed and securely connected. Make sure you have removed the lens cap and that the blue Power Indicator Light is ON. Verify that the Lamp Indicator Light is OFF. If the Lamp Indicator Light is ON, the lamp module must be replaced. Refer to page 32 for the lamp module replacement procedure. Verify that the Temp Indicator Light is OFF. If it is ON, refer to page 14. If you are using a notebook computer, you may need to activate the external monitor port. Please consult the computers manual for instructions. Key sequences for many computers are printed in your quick start guide. Check for damaged connector pins. Check that the projectors lamp hasnt burned out or been installed incorrectly. Problem: Partial, scrolling or incorrectly displayed image. Press the Auto Image button on the projector or use the Auto Image function in the Computer Image menu of the On Screen Display (OSD). If you are using a computer: If the resolution of your computer is higher than 1024768 for the hp xb31 or 800600 for the hp sb21, the projector will re-size the image to match the output of the computer. If desired, you may reset your computers display resolution to match these by following the steps provided in your computers owners manual. You may have to disable the computers monitor to correctly display the new resolution. Switch the notebooks display to the external display only or CRT only mode following the instructions provided in your computers owners manual. If you experience difficulty in changing the resolution settings, or your monitor freezes, restart the computer and the projector. Problem: The notebooks screen is not displaying your presentation. Some notebook PCs may deactivate their own screen when a second display device is in use. Refer to your computers documentation for information. If you are using a notebook computer, you may need to activate the external monitor port. Please consult the computers manual for instructions. Key sequences for many computers are printed in your quick start guide.

CAUTION! AVOID BURN HAZARD.
The lamp gets hot during normal operation. Allow it to cool down for 30 minutes before changing lamp!

CAUTION! CUT HAZARD.

If the bulb is broken, use caution to avoid injury.
WARNING! MERCURY HAZARD. This projectors bulb contains a small amount of mercury. If the lamp breaks, adequately ventilate the area where the breakage occurred. The projector bulb may require special handling and disposal at end-of-life.
Changing the lamp module (continued)
NOTE: For both the xb31 and the sb21 digital projectors, a Phillips-head screwdriver is required for this procedure.

hp xb31 specifications

Light Engine Brightness Contrast Ratio Lamp Number of Pixels Displayable Colors Projection Lens Projection Screen Size Projection Distance Video Compatibility H. Frequency V. Frequency Power Supply Power Consumption Uniformity I/O Connectors Single Chip DLPTM Technology 1500 comparable lumens 1800:1 (Full On/Full Off) 156 watt (W) user-replaceable P-VIP Lamp Module 1024 (H)768 (V) 16.7 million F/2.44~2.69, f=28.8~34.5 mm with optical 1.2:1 zoom and manual focus 0.7~7.5 m (28~295 inches) Diagonal 1.14~12 m (3.7~39.4 feet) NTSC 3.58/NTSC 4.43/PAL/PAL-M/PAL-N/SECAM and HDTV compatible Composite video, S-video, and component video (via optional cable) 15 kHz~100 kHz horizontal scan rate 43 Hz~120 Hz vertical refresh rate Universal AC input 100~240V; Input Frequency 50/60 Hz 220 watts 85% (JBMA) Power: AC power input socket Computer Input: One 35-pin VESA M1-DA for Analog RGB/Digital/ Component Video/HDTV/USB mouse Video Input: One Composite Video RCA input One S-video input Audio Input: One phone jack for mono audio input 1.6 kg (3.5 pounds) 22618367 mm (8.927.232.67 inches) Operating Temperature:
Weight Dimensions (WHD) Environmental
Operating Temperature (C) 10-40 10-35 10-30 10-28
Altitude (ft) 0 ~ 2,500 2,500 ~ 5,000 5,000 ~ 7,000 7,000 ~ 10,000

Safety Regulation

Storage Temperature: -20 C~60 C (-4 F~140 F) at 80% maximum humidity (0~40,000 ft) See page 38 for regulatory information 34
hp xb31 compatibility modes

Mode Resolution ANALOG

V.Frequency (Hz) 43.75 66.66 66.68 74.75.H.Frequency (Hz) 31.5 37.9 37.9 31.5 37.9 37.5 43.3 31.5 37.9 35.2 37.9 48.1 46.9 53.7 35.5 48.4 56.5 60.0 68.7 63.95 79.98 34.49.725 60.24 68.68 31.35 68.03 97.68.90.9

regulatory information

Regulatory information
This section presents information that shows how your digital projector complies with regulations in certain regions. Any modifications to your digital projector not expressly approved by Hewlett-Packard could void the authority to operate the digital projector in these regions. U.S.A. This digital projector has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This digital projector generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this digital projector does cause harmful interference to radio or television reception (which can be determined by unplugging the unit), try the following: Reorienting or relocating the receiving antenna. Relocating the digital projector with respect to the receiver. Connecting the digital projectors power cord to another power outlet. Connections to Peripheral Devices To maintain compliance with FCC Rules and Regulations, use properly shielded cables with this device. For more information, consult your dealer, an experienced radio/television technician, or the following booklet, prepared by the Federal Communications Commission: How to Identify and Resolve Radio-TV Interference Problems. This booklet is available from the U.S. Government Printing Office, Washington, DC 20402, Stock Number 004-000-00345-4. At the first printing of this manual, the telephone number was (202) 512-1800.

Japanese Notice

DECLARATION OF CONFORMITY
According to ISO/IEC Guide 22 and EN 45014 Manufacturers Name: Manufacturers Address: Hewlett Packard Company Hewlett Packard Company 1000 NE Circle Boulevard Corvallis, OR 97330-4239 Digital Projector xb31, sb21 All
Declares, that the product(s): Product Name: Model Number(s): Product Options:
Conforms to the following Product Specifications: Safety: EMC: IEC 60950: 1991 + A1, A2, A3, A4 / EN 60950: 1992 +A1, A2, A3, A4, A11, IEC 60825-1: 1993 + A1 / EN 60825-1: 1994 + A11 Class 1 LED CISPR 22: 1997 /EN 55022: 1998, Class B [1] CISRP 24: 1997 / EN 55024: 1998 IEC 61000-3-2: 1995 / EN 61000-3-2: 1995 + A1: 1998 + A2: 1998 IEC 61000-3-3: 1994 / EN 61000-3-3: 1995 FCC Title 47 CFR, Part 15 Class B / ANSI C63.4: 1992 ETS 300-328 Technical requirements for Radio equipment Notified Body Number: 0682 Notified Body Address: CETECOM ICT Services GmbH, Untertuerkheimer Str. 6-10, D-66117 Saarbruecken

Equipment Class 2:

Supplementary Information: The product herewith complies with the requirements of the Low Voltage Directive 73/23/EEC, the EMC Directive 89/336/EEC and carries the CE marking accordingly. The product herewith complies with the requirements of the EMC Directive 89/336/EEC and carries the CE marking accordingly. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. [1] The product was tested in a typical configuration with Hewlett Packard Personal Computer peripherals. Corvallis, OR, May 20, 2002 Section manager signature European Contact: Your local Hewlett Packard Sales and Service Office or Hewlett Packard GmbH, Department ZQ/Standards Europe, Herrenberger Strasse 140, D-7030 Boeblingen (FAX: +49-7031-143143). USA Contact: Hewlett Packard Co., Corporate Product Regulations Manager, 3000 Hanover Street, Palo Alto, CA 94304. Phone: (650) 857-1501.
Reference Safety Information

Laser Safety

The remote controller used with the digital projector is certified as a Class 1 laser device according to the U.S. Department of Health and Human Services (DHHS) Radiation Performance Standard and International Standards IEC 825 / IEC 825-1 (EN 60825 / EN 60825-1). This device is not considered harmful, but the following precautions are recommended:
Ensure proper use by reading and following the instructions carefully. If the unit requires service, contact an authorized hp service center See page 37 for details. Do not attempt to make any adjustment to the unit. Avoid direct exposure to the laser beam do not open the unit.

LED Safety

The infrared port located on the right side of the digital projector is classified as a Class 1 LED (light-emitting diode) device according to International Standard IEC 825-1 (En 60825-1). This device is not considered harmful, but the following precautions are recommended:
If the unit requires service, contact an authorized hp service center See page 37 for details. Do not attempt to make any adjustment to the unit. Avoid direct eye exposure to the infrared LED beam. Be aware that the beam is invisible light and cannot be seen. Do not attempt to view the infrared LED beam with any type of optical device.

Warranty & Support

Refer to warranty/support information data sheet enclosed with the projector or contact hp post-sales support at www.hp.com/support/digitalprojectors or call (in the US) 208-323-2551 or (in Canada) 905-206-4663. hp offers telephone support world-wide. For the phone number of the customer care center nearest you, please visit the following URL: http://productfinder.support.hp.com/tps/CLC?h_product=top&h_lang=en&h_r egion=emea&h_tool=phone

HP Digital Projector xb31/sb21
Designed for the business professional who needs to project a high-quality image with ease.

Quality image

For the highest-quality image. The HP Digital Projector xb31 provides industry-leading brightness and the highest resolution for impressive presentations, in a micro-portable weight that is still light enough to carry easily from room to room. Industry-leading brightness in any setting. Even with the room lights on, your audience will see your presentation with optimal claritythe HP Digital Projector xb31 features 1500 ANSI (max) lumens. Sharp, clear, accurate. Your presentation will look as good projected as it does on your computer screen with a TI DLP light engine, True XGA resolution (1024 x 768 dpi with the xb31 model) and high contrast ratio.

Easy-to-use

Easily adapts to any venue. Both HP digital projector models are equipped with built-in, full-screen NTSC/PAL/SECAM video capability, and compatibility with S-video, composite, component and HDTV terminals plus SXGA (xb31 model only), XGA, SVGA, VGA and Mac from one M1-AD input terminal. Simple presentation setup. Equipped with automatic image synchronization for easy tracking, frequency and position adjustment. Simple device setup. These HP digital projectors automatically detect computer signal input and resize images to a full screen, giving users the flexibility they need to switch sources quickly and easily for any presentation. Flexibility. A wireless remote control with USB mouse function and a laser pointer give you the freedom to move about the room and engage your audience.

Mobile

Lighter than most laptops. At just over two pounds, the HP Digital Projector sb21 is designed for the mobile professionalit lets you present a high-quality image in a compact design that wont weigh you down. You dont give up brightness. This micro-portable projector that fits into a purse or briefcase pouch also projects a bright, sharp, clear image with 1000 ANSI (max) lumens, True SVGA resolution (800 x 600 dpi with the sb21 model) and a high contrast ratio. Perfect partners. An HP digital projector combined with an HP notebook computer help you stay productive, mobile and successful, and they both feature HP reliability and compatibility for worry-free performance.
HP Digital Projector xb31 1. Projection zoom lens 2. Optical zoom 3. Six command keys and 3 LED indicators 4. NTSC/PAL/SECAM video through S-video, composite, component or HDTV (up to 1080i connections) 5. SXGA, XGA, SVGA, VGA and Mac compatibility with one MD-I terminal 6. 3.5 mm phone jack for audio input 7. Built-in 2-watt speaker 8. High-efficiency cooling system with low acoustic noise level
HP Digital Projector xb31
HP Digital Projector sb21 1. High-efficiency cooling system with low acoustic noise level 2. Digital zoom 3. Projection fixed lens 4. Six command keys and 3 LED indicators 5. XGA, SVGA, VGA and Mac compatibility with one MD-I terminal 6. Built-in full screen NTSC/PAL/ SECAM video through S-video, composite, component or HDTV connections
HP Digital Projector sb21
HP Digital Projector xb31: Unbelievable brightness, unbelievable contrast ratio TI DLP light engine for the brightest, highest-contrast image possible 1500 ANSI (max) lumens for a bright picture with the room lights on 1800:1 JBMA1/400:1 ANSI2 contrast ratio for deep blacks and rich, full colors True XGA (1024 x 768 dpi) for optimal clarity No surprises imaging 8.9 x 7.2 x 2.6 inches 3.5 pounds
HP Digital Projector sb21: Unbelievable size, unbelievable weight Fits in a pocketbook or with a laptop in your briefcase TI DLP light engine for the brightest, highest-contrast image possible 1000 ANSI (max) lumens True SVGA (800 x 600 dpi) resolution 7.9 x 5.5 x 2.3 inches 2.2 pounds

Japan Business Machine Makers Association American National Standard Institute
Superb imaging qualitywhat you see on your laptop is what you see projected on the screen!
If your presentation looks good, you look good. Whether pitching a new product, describing a designs progress, providing training or presenting financial results, you only have one opportunity to engage and convince your audience. HP digital projectors are perfect for mobile professionals presenting in a variety of rooms onsite or around the worldwho demand a projector that will deliver polished and professional presentations with a high-quality image. These lightweight, easy-to-use projectors provide uncompromising image brightness, contrast and resolution, assuring that you and your presentation get results. HP helps you fulfill the high standards that the fast-paced, competitive marketplace has established. Photographs project clearly with accurate colors, CAD drawings and plans are projected with high resolutioneven the most detailed spreadsheets are easy to readand your presentation can include both digital and analog input. Plus with the HP digital projectors quiet performance and ability to project vivid images even with the room lights on, you can stay engaged with your audience, lead support exercises and get your messages across without raising your voice. Complete mobile solutions from a trusted partner Customers around the world count on HP to provide business-critical support that gets results and contributes to business success. The HP digital projector complements the HP product portfolio, including the entire HP notebook PC line, HP handheld PCs and PDAs, HPs portable Deskjet printer and business desktop PCs. For easy compatibility, HP Digital Projectors work with any computerPC or Macintoshbut you will benefit from optimized performance when you use it as part of an HP mobile solution. When combined with the HP notebook PC, the presentation ready mode hot key automatically adjusts power management and disables screen savers while locking in the signal to the projector. One button is all it takes to make your HP notebook talk seamlessly to your projector.
And with HP digital projectors you are assured the highest image quality with no hassles reliability. HP has developed the industry standard for high-resolution printed images and scanning technology and now you can count on those same high-quality images printed to the screen. Plus, with HPs reputation for reliability and the digital projectors two-year expedited repair warranties, you can focus on your presentation and let HP take care of the rest. The freedom to connect with your audience Industry-leading contrast ratio, bright imaging and accurate colors capture and keep the attention of your audience and project the best image of you and your presentation: 1800:1 JBMA1/400:1 ANSI2 contrast ratio provides high definition and clear details. DLP light processor allows maximum brightness in a small, lightweight size. Image is bright enough to be effective even in rooms with the lights on. HP digital projector technology provides great color matching. Quiet 35 dBA noise level allows you to hear questions and comments and to be heard without raising your voice. Full-functionality remote control allows you to control your presentation while staying engaged with your audience. The lightweight, small size and versatile connections allow you to pack, go and present whenever and wherever you need to: Choose from the micro-portable xb31 at 3.5 pounds or the sb21 at 2.2 pounds. Connect to any input sourceS-video, composite, component and HDTV terminals, and one MD-I terminal for SXGA/XGA/SVGA/VGA/Mac compatibility (SXGA in xb31 only).

1 Japan Business Machine Makers Association 2 American National Standard Institute

Technical specifications

Brightness Resolution
HP Digital Projector xb31 (Product number: L1511A)
HP Digital Projector sb21 (Product number: L1510A)
1000 ANSI (max) lumens 1500 ANSI (max) lumens True SVGA (800 x 600), interpreted XGA (1024 x 768) resolution; True XGA (1024 x 768), interpreted SXGA (1280 x 1024) resolution; 16.7 million colors 16.7 million colors Image contrast 1800:1 JBMA (Japan Business Makers Association) 400:1 ANSI (American National Standards Institute) Lamp life 20+ months usage typical (1,500 hours to 50% lumens output) Adjustable from 25 to 300 inches (diagonal) Projected image size Adjustable from 28 to 295.3 inches (diagonal) 3.3 to 39.4 feet Throw distance 3.7 to 39.4 feet Single-panel 0.55 in 12 DDR DMD SVGA (TI DLP) Display technology Single-panel 0.7 in 12 DDR DMD XGA (TI DLP) Image compression/Scaling technology Intelligent zoom, XGA compression f/2.4, f=21.9 mm fixed focal lens (digital zoom; manual focus) Projector lens f/2.44~2.69, f=28.8~34.5 mm; 1.2x manual zoom lens (optical zoom; manual focus) Keystone correction 16 (32 total) Noise level 32 dBA peak under 25 C, 35 dBA typical under 25 C, 39 dBA maximum under 40 C Video capability NTSC: M (3.58 MHz), 4.43 MHz; PAL: B, D, G, H, I, M, N; SECAM: B, D, G, K, K1, L; HDTV: 480i, 480p, 720p, 1080i 120-watt compact P-VIP lamp (user replaceable) Lamp type 150-watt compact P-VIP lamp (user replaceable) N/A Audio Built-in two-watt speaker 2.5 mm phone jack Video composite input RCA jack Automatic (800 x 600 full screen) Automatic (1024 x 768 full screen) Resizing of images to full screen Automatic Detection of computer signal input Automatic Image synchronization Wireless remote control with USB mouse function and laser pointer Remote control Ceiling or tripod Mounting capability 7.9 x 5.55 x 2.3 inches 8.92 x 7.23 x 2.67 inches Dimensions (l x w x h) 2.2 lb 3.5 lb Weight (approximate) HP Digital Projector sb21, standard accessories: AC power cord (1.8 m), HP Digital Projector xb31, standard accessories: VESA M1-A to D-sub Whats in the box VESA M1-A to D-sub and USB cable (1.8 m), USB mini-B 5-pin to 4-pin and USB cable (1.8 m), 4-pin S-video to 4-pin S-video cable (1.8 m), S-video cable (1.8 m), 2.5 mm phone jack to RCA composite-video cable, RCA jack to RCA composite-video cable (1.8 m), 3.5 mm phone jack to wireless remote control with USB mouse function and laser pointer, two 2.5 mm phone jack audio cable, wireless remote control with USB mouse batteries, tethered lens cap, carrying bag, multi-language Users Guide function and laser pointer, two batteries, tethered lens cap, carrying bag, (CD-ROM), multi-language Quick Start Card, support information data sheet multi-language Users Guide (CD-ROM), multi-language Quick Start Card, support information data sheet

Ordering information

Onscreen languages Environmental ranges Operating temperatures: Storage temperatures: Power requirements Input voltage: Power consumption Maximum: Power certification Safety certifications: Electromagnetic compatibility: Warranty 435, ABG, AB2, ABU, 401, ABJ, ABA, 436, ABZ, ABY, to 104 F (10 to 40 C) 4 to 140 F (-20 to 60 C) Universal AC 100-240V, 50/60 Hz with PFC input xb31: 220 watts, sb21: 160 watts FCC Part 15, Class B; CE-Class B; VCC Class B; BSMI; UL; CUL; TV-GS FCC Part 15, Class B; CE-Class B; VCC Class B; BSMI; UL; CUL; TV-GS Standard warranty: two-year parts and labor, two-year expedited repair or express exchange, two-year 24/7 phone support; lamp module90 days/500 hours; accessories 90 days, HP web support, HP e-mail support Product number L1511A L1510A HP product HP Digital Projector xb31 HP Digital Projector sb21
Optional accessories L1513A Ceiling mount connector L1515A Lamp module for sb21 model L1516A Lamp module for xb31 model L1523A USB to M1-AD cable L1528A International AC power cords (1.8 m) L1529A M1-AD to DV-1 USB cable (1.8 m)
HP recommends Microsoft Windows XP Professional for mobile computing.
Microsoft and Windows are U.S. registered trademarks of Microsoft Corporation. 2003, 2004 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.
For more information visit our website at www.hp.com
5980-9857ENUC, 6/18/2004, Rev. 3