Glass cleaning hp scanjet 4500c/5550c scanner
Before proceeding, read these instructions all the way through. Then return here and follow the steps in order.
This module is organized into the following sections:
preparation disassembly cleaning reassembly

preparation

Tools needed:
flat-head screwdriver phillips screwdriver

Supplies needed:

Glass cleaner lint-free cloths Disconnect the USB cable between the scanner and computer. Disconnect the power supply from the scanner.
Wait at least 15 minutes (after disconnecting power) before dissembling the scanner and cleaning the glass. This gives the scanner time to cool.
disassembly remove the scanner lid
After steps 1 and 2 have been completed and the scanner has cooled for 15 minutes, you can remove the lid as shown. 3 Open the lid and lift it straight up.
Scanner lid being removed

Set the lid aside.

Clean top of the scanner Clean the outside of the scanner prior to disassembly to prevent contamination of internal parts.
Use only glass cleaner. Avoid abrasives, acetone, benzene, and carbon tetrachloride, all of which can damage the scanner glass. Avoid isopropyl alcohol because it can leave streaks on the glass.
Do not spray the glass cleaner directly on the glass. Do not allow the cleaner to seep between the glass and the plastic. If liquid gets between the glass and the plastic it could stain the calibration strip ( the white strip under the glass) and render your scanner useless. If the cleaner gets in the calibration strip area, the scanner must be sent to hp for repair.
Apply glass cleaner to a soft lint-free cloth. Clean the plastic first. Apply the glass cleaner sparingly to a separate cloth and clean the glass.
Unlatch the top cover Begin disassembly only after completing steps 1 through 6
You are about to expose the interior of the scanner to the dust of the outside environment. the scanner is very sensitive to dust; any dust particles that get into the carriage head can cause streaks in the scanned image. Minimize the time that the top cover is off by having all the cleaning materials ready. Also be sure to disassemble your scanner in a clean environment.
7 Using a Phillips screwdriver remove the four screws from the bottom of the scanner. See the following illustration for the location of the screws.

location of the screws

8 Holding the top and bottom cover together, turn the unit back over so that the glass side is facing up.
9 Insert a flat-head screwdriver into the slot on the back of the scanner. The slot is located above the ADF port between the top cover and the base. Pry the top cover up with a screwdriver.
flat-head screwdriver being inserted between base and top cover
remove the top cover After unlatching the top cover, you are ready to remove it.
top cover being lifted up
10 Carefully lift the top cover off the base. Turn the top cover upside down and set it on a clean surface
Dust will immediately begin accumulating in your scanner now that the top cover is off. Minimize the time the scanner base is exposed. Read all directions and have the necessary tools ready before removing the top cover. While the top cover is off do not leave the scanner unattended.
Static discharge from your fingers, hand, or tools will damage the circuit boards inside your scanner. Do not touch anything inside the scanner base.
Cleaning clean the glass You are now ready to clean the underside of the glass.

Apply glass cleaner sparingly to a soft, lint-free cloth and clean the glass.
reassembly re-mount the top cover to the scanner When you have finished cleaning the underside of the glass, reassemble the top cover. 12 Hold the top cover directly above the scanner and lower it into position as shown.
top cover being lowered onto base
13 snap the back of the scanner together bus squeezing the top cover and the base together at the ADF port.
latching the top cover and base
14 Holding the top and bottom covers together, turn the scanner upside down on a clean surface. insert the screws 15 Re-insert and tighten the four screws with a Phillips screwdriver.

Step #7

Insert the screws

location of screws

16 Turn the unit over so that the glass side is facing up. insert the scanner lid you can now re-insert the scanner lid, with the lid in the open position. 17 Align the lid hinges with the slots of the top cover and slide them in.
scanner lid being re-inserted in scanner

Close the scanner lid.

reconnect your scanner You can now reconnect the usb cable and the power supply to the scanner. For instructions on connecting the cables see the setup instructions that came with your scanner.

hp scanjet 4500c and 5500c series scanners

user's manual

P_usermanual.book Page 1 Tuesday, April 16, 2002 10:44 AM

users manual

P_usermanual.book Page 2 Tuesday, April 16, 2002 10:44 AM

copyright information

Copyright Hewlett-Packard Company 2002 All rights reserved. Reproduction, adaptation, or translation without prior written permission is prohibited, except as allowed under copyright laws. This product incorporates Adobe's PDF technology, which contains an implementation of LZW licensed under U.S. Patent 4,558,302.

trademark credits

Adobe and the Acrobat logo are either registered trademarks or trademarks of Adobe Systems Incorporated in the United States and/or other countries/ regions. Microsoft and Windows are registered trademarks of Microsoft Corporation. All other product names mentioned herein may be trademarks of their respective companies.

warranty

The information contained in this document is subject to change without notice. Hewlett-Packard makes no warranty of any kind with respect to this information. HEWLETTPACKARD SPECIFICALLY DISCLAIMS THE IMPLIED WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Hewlett-Packard shall not be liable for any direct, indirect, incidental, consequential, or other damage alleged in connection with the furnishing or use of this information. The TWAIN Toolkit is distributed as is. The developer and distributors of the TWAIN Toolkit expressly disclaim all implied, express or statutory warranties including, without limitation, the implied warranties of merchantability, noninfringement of third party rights and fitness for a particular purpose. Neither the developers nor the distributors will be liable for damages, whether direct, indirect, special, incidental, or consequential, as a result of the reproduction, modification, distribution or other use of the TWAIN Toolkit. NOTICE TO U.S. GOVERNMENT USERS: RESTRICTED RIGHTS COMMERCIAL COMPUTER SOFTWARE: Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph (c) (1) (ii) of the Rights in Technical Data Clause at DFARS 52.2277013. Material scanned by this product may be protected by governmental laws and other regulations, such as copyright laws. The customer is solely responsible for complying with all such laws and regulations.
product restricted material
This HP product contains the following materials that might require special handling at endof-life: mercury in the fluorescent lamp in the scanner/transparent materials adapter/liquid crystal display (< 5 mg) lead in solder For recycling information, you can contact http://www.hp.com/go/recycle, your local authorities, or the Electronics Industries Alliance at http://www.eiae.org. For information about HPs environmental stewardship program, see the Warranty and Specifications section of the electronic Help for your scanner.
P_usermanual.book Page iii Tuesday, April 16, 2002 10:44 AM

contents

install the scanner. 1
before you begin. install the software and connect the scanner. connect the ADF. connect the APF. connect the TMA. 5
scanner overview. 6 how to use the scanner. 7
scan pictures. post a picture on a website. save a document. create a photo show and save it on CD. e-mail a scan. print copies. cancel a scan in progress. use the power save button. enable instant scanning. scan from the ADF. scan from the APF. scan slides or negatives. 7. 8. 8. 12

installation problems - hp scanjet 4500c/5500c series 13
scanner is not working. 13 scanner initialization failed. 14 scanner still does not work properly. 14

hp support. 16

find hp help on the web. 16 contact hp customer support. 17

before you begin

install the scanner
Make sure that you have a universal serial bus interface connection (USB port) on your computer and that your computer is running Microsoft Windows 98 or later or Macintosh OS 9 or later.

USB port

check the box contents
Your scanner box should contain the following items: HP Scanjet digital flatbed scanner HP Photo & Imaging software CD-ROM USB cable Power cable Automatic document feeder (ADF) (HP Scanjet 5550c only) Automatic photo feeder (APF) (HP Scanjet 5500c only) Transparent materials adapter (TMA) (HP Scanjet 4750c/5500c only)
HP Scanjet 4500c/5550c scanner
ADF (HP Scanjet 5550c only)
HP Scanjet 4570c/5500c scanner TMA
APF (HP Scanjet 5500c only)
install the software and connect the scanner
Set up your scanner in one of two ways: either install the software first or connect the scanner first. It is recommended that you install the software first, especially on a Macintosh computer.
If you experience difficulty installing your scanner, see installation problems - hp scanjet 4500c/5500c series on page 13.
install the software first (Windows and Macintosh)
Close all open programs on your computer. Locate the HP Photo & Imaging software CD-ROM that is appropriate for your language and operating system and insert it into your computer. For a Microsoft Windows computer: Follow the instructions on the screen. Or, if the installation program does not start automatically: a. On the Start menu, click Run. b. Type: x:setup.exe (where x is the letter of the CD-ROM drive). For a Macintosh computer: Double-click the Installation Read Me file on the CD-ROM and follow the instructions. If the instructions prompt you to shut down your computer, do so. Connect the USB cable between the USB port on the scanner and the USB port on the computer. Connect the power cable between the scanner and a surge protector or a grounded wall outlet that is easy to reach. This turns on the scanner. If necessary, turn your computer on again.
A 00 in the LCD on the front panel of the scanner indicates that a USB connection error has occurred. Check that the USB cable is securely connected between the scanner and the computer.

P_usermanual.book Page 3 Tuesday, April 16, 2002 10:44 AM
connect USB cable to scanner
connect USB cable to computer
connect the scanner first (Windows only)
Make sure that your computer is on and that the operating system is running. Connect the USB cable between the USB port on the scanner and the USB port on the computer. Connect the power cable between the scanner and a surge protector or a grounded wall outlet that is easy to reach. This turns on the scanner. Follow the prompts in the New Hardware Found wizard. Insert the HP Photo & Imaging software CD-ROM and click Next. If the wizard prompts you for a drive letter, select your CD-ROM drive. In the HP Scanjet installation program, follow the instructions. After installation is complete, another HP installation program starts. You can install additional software, register your scanner, and find additional help. To see if your scanner came with additional software, click Install software and follow the prompts.
P_usermanual.book Page 4 Tuesday, April 16, 2002 10:44 AM

connect the ADF

If your scanner has an automatic document feeder (ADF), it allows you to scan multiple pages. 5 Disconnect the power cable from the scanner. If your scanner has a lid attached to it, remove the lid by raising it and then pulling it straight up. Attach the ADF by inserting the ADF hinges into the scanner hinge slots. Connect the ADF cable to its port on the scanner. Reconnect the power cable.

ADF port

connect the APF
If your scanner has an automatic photo feeder (APF), it allows you to scan multiple photos. 5 Disconnect the power cable from the scanner. If your scanner has a lid attached to it, remove the lid by raising it and then pulling it straight up. Attach the APF by inserting the APF hinges into the scanner hinge slots. Connect the APF cable to its port on the scanner. Reconnect the power cable.

APF port

P_usermanual.book Page 5 Tuesday, April 16, 2002 10:44 AM

connect the TMA

If your scanner has a transparent materials adapter (TMA), it allows you to scan 35 mm slides or negatives. Disconnect the power cable from the scanner. On the back of the scanner, find the round TMA port: On the HP Scanjet 4500c and 5550c series scanners, the TMA port is the second port from the left. On the HP Scanjet 4570c and 5500c series scanners, the TMA port is the second port from the right. Holding the TMA cable by its free end, align the connector so the arrow is on the top side. Gently insert the connector into the TMA port. Reconnect the power cable.

TMA port

P_usermanual.book Page 6 Tuesday, April 16, 2002 10:44 AM

scanner overview

Description
Scans the item into the HP Photo & Imaging software. Scans the item and sends it to a website. Scans the document and saves it to a CD or to your hard disk (HP Scanjet 4500c/5550c only). Scans the item to the Memories Disc Creator software, where you can create a photo show on a CD, along with background music and titles (HP Scanjet 4570c/5500c only). Scans the item using settings optimized for e-mail and sends the scan to your e-mail software (if the software is supported). Scans the item and sends it to a printer to make copies. Selects the number of copies to be printed with the COPY button.

This section describes the buttons on the front panel of the scanner and available accessories. Feature
SCAN button SHARE-TO-WEB button SAVE DOCUMENT TO DISC button MEMORIES DISC CREATOR button E-MAIL button COPY button NUMBER OF COPIES button
COLOR/BLACK & WHITE copy Determines whether items will be scanned in color or in black and white button when you press the COPY button. POWER SAVE button CANCEL button 2-digit LCD Turns off the scanner lamp, the LEDs, and the LCD. Cancels a scan while the scanner is scanning, or cancels a series of scans from the ADF. Displays the number of copies that will print with the COPY button. Also displays error codes that identify scanner problems.
HP Scanjet automatic document Allows you to scan multiple pages automatically (HP Scanjet 4500c/ feeder (ADF) 5550c only). HP Scanjet automatic photo feeder (APF) HP Scanjet transparent materials adapter (TMA) Allows you to scan multiple photos automatically (HP Scanjet 4570c/ 5500c only). Scans 35 mm slides or negatives to the HP Photo & Imaging software, where you can preview or change the scanned image.
P_usermanual.book Page 7 Tuesday, April 16, 2002 10:44 AM

how to use the scanner

You can start your scanner projects in one of two ways: from the scanner buttons or from the HP Photo & Imaging software. The scanner buttons offer shortcuts to some of the software functions. Start from the software when you want more options and control or if your scanner model does not have all the buttons.
Macintosh users: For information about how to scan from the HP Macintosh software or change the button settings for your scanner, see the online help in the Apple Help Center.
The procedures in this section use the default button settings. For more information about changing the settings for one or more buttons, see change button settings in the HP Photo & Imaging software Help.
For more information about using the software, see the HP Photo & Imaging software Help.

scan pictures

You can scan pictures into the HP Photo & Imaging software by pressing the ). SCAN button ( Close the HP Copying software if it is open on your computer. Place the original face down on the scanner glass and close the lid. Press the SCAN button on the front panel of the scanner. Follow the instructions on your computer screen.
to change the original type

You can change the setting for the SCAN button so that it regularly scans using settings optimized for documents or pictures. For more information, see change button settings in the HP Photo and Imaging software Help.
P_usermanual.book Page 8 Tuesday, April 16, 2002 10:44 AM
to scan from the software
You can also preview and modify documents and pictures from the software. On the Start menu, point to Programs, point to Hewlett-Packard, point to your scanner, and click hp photo & imaging director. In the Director, click Scan Document or Scan Picture.
post a picture on a website
If you have an Internet connection, you can easily post your pictures to the Web from your scanner. After you set up a website by using HP Share-to-Web, you can give people an address where they can view your pictures. Close the HP Scanning software and the HP Copying software if they are open on your computer. 2 Place the original item face down on the scanner glass and close the lid. 3 Press the SHARE-TO -WEB button ( ) on the scanner. The scanner scans the item using default settings optimized for the Web. 4 Follow the instructions on your computer screen. You can also post scans to a website from the software. For more information, see the HP Photo & Imaging software Help. 1
If you want to place a scan on a website that is not enabled for HP Share-to-Web, save the scanned image as a file and then place the file on the site.

save a document

The HP Scanjet 4500c and 5550c scanners have a SAVE DOCUMENT TO DISC button ( ). You can scan a document and send it directly to a compact disc (CD), if you have a read/write CD drive that supports direct writing to the CD. Alternatively, you can save the scan on your hard disk; by default the scan is saved in the My Documents folder if you have a Windows computer, in Documents if you have a Macintosh computer.
to save a document by using the Save Document to Disc button
Close the HP Scanning software and the HP Copying software if they are open on your computer. 2 Place the original face down on the scanner glass and close the lid. 3 Press the SAVE DOCUMENT TO DISC button on the scanner and follow the prompts on the computer screen. The software scans the document using default settings optimized for document storage. When you use the SAVE DOCUMENT TO DISC button, your scan is saved as an Adobe Portable Document Format (PDF) file. To save your scan with a different format, use the HP Photo & Imaging software. Open the Director and click SCAN DOCUMENT. 1
P_usermanual.book Page 9 Tuesday, April 16, 2002 10:44 AM
To change the location where a file is saved when you press the SAVE DOCUMENT TO DISC button, change the buttons settings. You can also change the original size, resolution, and file name. For more information, see change button settings in the HP Photo and Imaging software Help. If your scanner does not have this button, you can scan documents and save them on CD from the software. For more information, see the HP Photo & Imaging software Help.

to select original type for e-mail
If the software prompts you for an original type, you have two choices: Picture or Document. The scanner uses optimized scan settings for your item depending on your choice. Use the following guidelines to determine the best original type for your needs. If your original consists of
Text, or both text and graphics A printed photograph or image
Select this original type

Document

Receive this type of output
Adobe Portable Document Format (PDF) file Joint Photographic Experts Group (JPG) file

Picture

If you need to save the item as a file type other than JPG or PDF, scan and save the item by using the HP Scanning software.
P_usermanual.book Page 11 Tuesday, April 16, 2002 10:44 AM
If the software does not prompt you for an original type, you can change the setting for the E-MAIL button so that it regularly scans using settings optimized for either documents or pictures. For more information, see change button settings in the HP Photo and Imaging software Help.

print copies

If your scanner has a COPY button ( directly to a printer to make copies. 3 ), you can scan an item and send it Close the HP Scanning software if it is open on your computer. Place the original face down on the scanner glass and close the lid. If you want to print a color copy, select the color setting by pressing the COLOR/BLACK & WHITE button on the front panel of the scanner. The light adjacent to the current selection is lit. Use color copy only if you are printing to a color printer and want a color copy. 4 Select the number of copies by pressing the NUMBER OF COPIES button on the front panel of the scanner. The liquid crystal display (LCD) shows the number of copies selected. The default setting is one copy. 5 Press the COPY button on the scanner. The software scans the item using default settings optimized for printing, and then the number of copies specified in the scanner LCD window are printed on the default printer. If you want to reduce or enlarge the copies, lighten or darken them, or change printer settings, click Cancel in the copy progress dialog box. You can then make changes to settings in the HP Copying software. You can also make copies from the HP Copying software. For more information, see the HP Photo & Imaging software Help.
cancel a scan in progress
The CANCEL button ( ) cancels a scan in progress. When you press the CANCEL button during a scan, the lamp returns to its starting position.

use the power save button
Use the POWER SAVE button ( ) to turn off the lamp when you are not using the scanner. When you press the POWER SAVE button, the scanner lamp, the small indicator lights, and the LCD turn off, and the scanner lamp returns to its starting position. To use the scanner again, press any button on the front panel of the scanner or start a scan from the computer. After a short warm-up cycle, the scan begins.

enable instant scanning

If the instant scanning feature is available on your scanner, you can start scanning right away, without waiting for the lamp to warm up. Your scanner has this feature if the Instant lamp warm-up option appears in the Quality vs. Speed tab, which you access by using the following procedure.
P_usermanual.book Page 12 Tuesday, April 16, 2002 10:44 AM
Open the Director and, on the Settings menu, click Scan Preferences. Click the Quality vs. Speed tab. To eliminate the lamp warm-up time and enable instant scanning, select the Instant lamp warm-up check box. To reduce power consumption, clear the Instant lamp warm-up check box.
If instant scanning is enabled, you can scan right away even after you have pressed the POWER SAVE button. Instant scanning does not function while you are using the TMA.

scan from the ADF

The HP Scanjet 4500c and 5550c scanners support the use of an automatic document feeder (ADF), which allows you to scan multiple-page items quickly and easily. For more information about the ADF, see ADF - hp scanjet 4500c/5550c in the HP Photo & Imaging software Help.

scan from the APF

The HP Scanjet 4570c and 5500c scanners support the use of an automatic photo feeder (APF), which allows you to scan multiple photos quickly and easily.
To prevent damage to your photos: do not use the APF to scan photos that are fragile, damaged, or irreplaceable do not use the APF to scan the same photo more than 5 times
For more information about the APF, see APF - hp scanjet 4570c/5500c in the HP Photo & Imaging software Help.

scan slides or negatives

You can use the optional HP Scanjet transparent materials adapter (TMA) to scan 35 mm slides or negatives. To do so, use the HP Scanning software rather than the scanning buttons. For more information about the TMA, see TMA - hp scanjet 4500c/5500c series in the HP Photo & Imaging software Help.

P_usermanual.book Page 13 Tuesday, April 16, 2002 10:44 AM

scanner is not working

installation problems hp scanjet 4500c/5500c series
This chapter contains solutions to common installation problems. For solutions to usage problems or maintenance issues, such as cleaning the scanner glass, see the troubleshooting section in the electronic Help.
First, check your computer: Make sure your computer meets the minimum system requirements that are listed on the scanner box. If you do not have enough hard-disk space, remove unnecessary files or install the software on a different disk drive. On a Microsoft Windows computer, if you receive a message such as Destination Directory Is Invalid or Program Folder Is Invalid during installation, do one of the following: Type a valid destination folder name. The destination folder cannot contain the following characters: /, \, :, ?, *, <, >, , or |. Find a valid folder using the Browse button. Check the cables: Check that the power cable is securely connected between the scanner and a live electrical outlet or surge protector. If the power cable is connected to a surge protector, make sure the surge protector is plugged into an outlet and turned on. Make sure you use the USB cable that was included with the scanner. Another USB cable might not be compatible with the scanner. Check that the USB cable is securely connected between the scanner and the computer. Disconnect the power cable from the scanner and turn off the computer. After 30 seconds, reconnect the power cable to the scanner and then turn on the computer, in that order. On a Macintosh computer, use the Apple System Profiler to make sure the scanner is connected to the computer correctly.
installation problems - hp scanjet 4500c/5500c series
P_usermanual.book Page 14 Tuesday, April 16, 2002 10:44 AM
Test the scanner hardware: a. Disconnect the USB cable and the power cable from the scanner. Make sure the power cable is still connected to the power source. ) and COPY ( ) buttons at the same time, b. Press the E-MAIL ( while reconnecting the power cable to the scanner. (Hold the scanner buttons for less than 5 seconds.) The scanner lamp should turn on. ) button. (Hold the button for less than 5 c. Press the SCAN ( seconds.) The carriage in the scanner should move forward and backward. d. To end the test, disconnect the power cable. If the scanner lamp does not turn on or the carriage does not move, a problem exists with the scanner hardware. Contact HP Customer Support.
scanner initialization failed
If you receive a message that the scanner initialization failed, or if the HP Scanning software stops working after it has been functioning properly, try the following procedures. a. Close the HP Scanning software if it is open. b. Make sure that the cables connecting the computer and the HP scanner are securely fastened. c. Turn the scanner off by disconnecting the power cable. Turn the scanner back on by reconnecting the power cable. d. Turn the computer off and then on again. A 00 in the LCD on the front panel of the scanner indicates that a USB connection error has occurred. Check that the USB cable is securely connected between the scanner and the computer. If the scanner still fails to initialize, run the Repair utility (Windows computers only) as described in the next topic, scanner still does not work properly.

scanner still does not work properly
If the scanner stops scanning or the buttons no longer work as they should, a software conflict might exist on your computer. You might need to reinstall the HP Photo & Imaging software. To do this, run the Repair utility (Windows computers only). a. Click Start, point to Settings, and then click Control Panel (in Windows XP, click Start, and then click Control Panel). b. Click Add/Remove Programs, and then select the HP Photo & Imaging software. c. Click Add/Remove (or Change, depending on your version of Windows).
P_usermanual.book Page 15 Tuesday, April 16, 2002 10:44 AM
d. Follow the instructions on the computer screen, and then click Repair. If this does not work, install the scanner on another computer. This will help determine if the problem is related to the first computer or to the scanner. If the scanner still does not work, contact HP Customer Support. If the troubleshooting information you need is not shown here, see the software ReadMe file for the most recent information, or review the troubleshooting section in the electronic Help.
P_usermanual.book Page 16 Tuesday, April 16, 2002 10:44 AM

hp support

For warranty and specifications, see the electronic Help for your scanner. For regulatory information, see the regulatory_supplement.htm file on the CD-ROM that came with your scanner.

find hp help on the web

HP provides several resources on the Web to provide help with your scanner. These Web services are free and available to you 24 hours a day, 7 days a week.

hp product support

Visit http://www.hp.com/cposupport/loc/regional.html, select your region, and then type your scanner model in the quick find box, to find information about the following topics: setting up and using your scanner downloading drivers solving a problem ordering warranty

hp scanjet website

Visit http://www.hp.com and click products and services for the following information: Tips for using your scanner more effectively and creatively HP Scanjet driver updates and software

accessibility website hp assistance
Customers with disabilities can get help by visiting http://www.hp.com/hpinfo/ community/accessibility/prodserv/. If you cannot find an answer to your question by using the websites listed above, visit http://www.hp.com/cposupport/mail_support.html. From there, you can discover how to contact HP by using e-mail, the telephone, and other methods.
P_usermanual.book Page 17 Tuesday, April 16, 2002 10:44 AM
contact hp customer support
Before contacting HP Customer Support, please see find hp help on the web. The website services described in that section are free and available to you around the clock. If you dont find what you need on the Web, please contact HP Customer Support. You can contact HP by telephone or mail for support and service for your scanner. Prices, availability, and hours of support are subject to change without notice.

how hp can help

Hewlett-Packard's support hotline can help resolve problems with: setup installation configuration operation For questions relating to operating systems or network configurations, contact your point of purchase or internal support department. For help with non-HP hardware or software, please contact the manufacturer of the other product.

before you call

Please try the following steps before you call HP Customer Support: Review the installation problems chapter in the users manual; for additional troubleshooting, see the troubleshooting module in the HP Photo & Imaging software Help. Review the troubleshooting information on the HP product support website.

when you call

If possible, be at the computer where the scanner is installed and have the following information ready when you call: serial number (found on the back or bottom of your scanner or under the scanner glass) product name (found on the scanner lid) date of purchase
obtain support in the United States
For information about your warranty, see warranty and specifications in the electronic Help.
free telephone support for the duration of your warranty
Within the period of your warranty, telephone support is provided to you free of charge. If this is a long distance call for you, long distance charges will apply. Call (208) 323-2551. Our support staff is available from 6 am to 10 pm Mountain Time, Monday through Friday, and 9 am to 4 pm on Saturday.
P_usermanual.book Page 18 Tuesday, April 16, 2002 10:44 AM

after the warranty period
Call (208) 323-2551. Charges are $25.00 per issue, charged to your credit card. If you think your HP product might need service, call HP Customer Support, which can help determine if service is required.
hewlett-packard upgraded warranty statement
You can buy an extended, comprehensive warranty for your HP product, but you must do so within 180 days of purchasing the product. Upgrade your standard factory warranty to three years with the HP SupportPack. Service coverage begins on product purchase date and the pack must be purchased within the first 180 days of product purchase. HP will determine the hardware service offering based upon the outcome of system self-test programs run by the customer through the initial call to HP Customer Support. If during your technical support call it is determined that your product needs replacement, then HP will ship you this replacement product the next business day free of charge. This warranty upgrade offers maximized uptime and productivity, the convenience of door-to-door pickup and delivery, with all packaging and freight prepaid by HP. Available in the US only. For more information call 1-888-999-4747 or visit http://www.homeandoffice.hp.com and select warranty upgrades under product support.

obtain support worldwide

Telephone support is free for one year in Asia and the South Pacific, and for 30 days in the Middle East and Africa. The information contained in this document and the applicable conditions for HP phone support are subject to change without notice. Please check for the latest information and conditions at http://www.hp.com/cposupport/loc/ regional.html. Alternatively, you can ask your dealer or call HP at the phone number listed in this document. For English support in Europe, contact +44 (0) 52 02.
P_usermanual.book Page 19 Tuesday, April 16, 2002 10:44 AM
Algeria Argentina Australia Austria Belgium Brazil
+0-810-555-43 (0) 6080 Dutch: +32 (0)8806 French: +32 (0)8807 (11) (greater So Paulo) 751 (outside greater So Paulo) 905 206-(Post-sales Business Computing) 999 (Post-sales Home Computing) +86 (10) ++42 (0)7310 +++358 (0)288 +33 (0)22 (Euro 0.34/min) +49 (0)(Euro 0.12/min) +5105 +85 (2) +36 (0)1111 ++62 (21) +353 (0)5525 +972 (0)+++82 (2) 080-999-0700 (outside Seoul and Kyung Ki only)

Malaysia

60 (3) (Penang) 2566 (Outside Penang) 9922 (Mexico City) 01-800-472-6684 (outside Mexico City) ++31 (0)8751 +64 (9) +10111 +63 (2) +00 +0589 +3154442 (local) +(Moscow) +(St. Petersburg) +(inside RSA) +27-9301 (outside RSA) ++46 (0)2170 +41 (0)0 800-+66 (2) (Bangkok) +++7 (380-44) 490-8454 +44 (0)52 02

Mexico

Morocco Netherlands New Zealand Norway Peru Philippines Poland Portugal Puerto Rico Romania Russian Federation Singapore South Africa

Canada Chile

China Colombia Czech Republic Denmark Egypt Finland France Germany Greece Guatemala Hong Kong SAR Hungary India Indonesia Ireland Israel Italy Japan Korea, Republic of
Spain Sweden Switzerland Taiwan Thailand Tunisia Turkey Ukraine United Arab Emirates United Kingdom and English internationally United States Venezuela Viet Nam

(208) 323-+84 (0)4530

www.hp.com

Printed in U.S.A. 2002

*C991090400*

C9910-90400