Reviews & Opinions
Independent and trusted. Read before buy Humminbird Matrix 97 GPS Chartplotter!

Humminbird Matrix 97 GPS Chartplotter

Manual

Preview of first few manual pages (at low quality). Check before download. Click to enlarge.
Manual - 1 page  Manual - 2 page  Manual - 3 page 

Download (English)
Humminbird Matrix 97 GPS Chartplotter - Installation Guide, size: 1005 KB
Instruction: After click Download and complete offer, you will get access to list of direct links to websites where you can download this manual.

About

Humminbird Matrix 97 GPS ChartplotterHumminbird Matrix 97 Combo - Marine Chartplotter - TFT - 320 x 240 - color

9″ x 3″ x 7″, 750 WPs

The Matrix 97 Combo features a brilliant color 240V x 320H 5" display, DualBeam PLUS sonar with 4000 Watts PTP power output, GPS Chartplotting with built-in UniMap, and advanced Fishing System capabilities.

Here you can find all about Humminbird Matrix 97 GPS Chartplotter, for example manual and review. You can also write a review.

 

[ Report abuse or wrong photo | Share your Humminbird Matrix 97 GPS Chartplotter photo ]

User reviews and opinions

<== Click here to post a new opinion, comment, review, etc.

Comments to date: 7. Page 1 of 1. Average Rating:
gabry 3:18am on Tuesday, November 2nd, 2010 
Business trip Acquires Satellites Quickly","Compact","Easy Menus","Easy To Read","Easy To Set Up","Reliable Performance","Simple Controls We use this product in the jungle of Peru (south America) and help us to find the way home and save our life most of the time.
jasajona 2:45am on Thursday, September 23rd, 2010 
Unit works wonderfully, very comprehensive and meaningful learning curve to a neophyte in GPS. Perhaps should have started with a simpler unit.
3danny 5:39am on Tuesday, September 21st, 2010 
Friendly air soaring use the GPS unit is great. I searched a long time and found that Tiger GPS had the best price. It is a fun toy! great gps for the lake had this for 2 years now, and never once got lost on the lake with it
Ryan_Singer 10:28am on Monday, September 6th, 2010 
Even works with my motorycle gloves on! Acquires Satellites Quickly","Compact","Easy Menus","Easy To Read","Easy To Set Up","Reliable Performance". I bought 2 of these - one for a gift and one to mount on my motorcycle. I tried this in my car.
TommySedin 1:39pm on Friday, July 16th, 2010 
Nice way to mount GPS on bike I had been rigging up my Garmin 96c to use on my bicycle. I spotted this mount online and figured to give it a try.
mniven 3:54pm on Wednesday, April 28th, 2010 
My wife purchased the GPSMAP 76cSx for me. We had no problems w/ ordering or shipping. The unit arrived in excellent condition. Score! This mount is designed for bike handlebars, but I use it on my boat. The very similar boat mount costs 3 or 4 times as much.
sam_uk 6:13pm on Thursday, April 1st, 2010 
"This is the best nav device I have ever used! This has the same screen, antenna and guts as the Garmin 60Csx, but floats on water and is cheaper. "I love this thing. I use it for geocaching and its great.

Comments posted on www.ps2netdrivers.net are solely the views and opinions of the people posting them and do not necessarily reflect the views or opinions of us.

 

Documents

doc0

RTS (Real Time Sonar) Window
and the depth of the bottom directly below the cursor. position is shown, the distance to travel to the cursor can be marked at the cursor position for later retrieval and use.
Second Sonar Return - when the sonar signal bounces between the bottom and the surface of the water and back again. Use the appearance of the second return to determine bottom hardness. Hard bottoms will show a strong second return, while soft bottoms will show a very weak one or none at all.
to the Matrix Fishing System. If both devices are connected, then only the information from the GPS receiver
The views available on your Matrix Fishing System are: Sonar views: Sonar View Zoom View 200/83 kHz Split Sonar View Big Digits View Side Beam View WideSide View Navigation views: Birds Eye View Chart View Combo View
NOTE: Side Beam View and WideSide View require the purchase of the QuadraBeamTM transducer for the Side Beam View and the WideSide transducer for the WideSide View. You can visit our website at www.humminbird.com to order these accessories online or contact our Customer Resource Center at 1-334-687-0503.
Sonar View is the default view. When the VIEW key is pressed, the display cycles through the available views. When the EXIT key is pressed, the display cycles through the available views in reverse order. Any view can be hidden or displayed as part of the view rotation using Select View from the Advanced Setup Menu.
NOTE: When you change any menu settings that affect the sonar, the view will update immediately (i.e. you dont have to exit the menu to apply the change to the screen).

Sonar View

Sonar View presents a historical log of sonar returns. Depth is always displayed. Readouts for temperature and speed are automatically displayed if the appropriate accessory is connected. The most recent sonar returns are charted on the right side of the window; as new information is received, the older information is moved across the display to the left. A Digital Depth Readout is displayed in the upper left corner. A scale with Upper and Lower Depth Range readouts appears along the right edge of the Sonar View. The scale indicates the distance from the surface of the water to a depth range sufficient to show the bottom. Depth Range is automatically selected to keep the bottom visible on the display, although you can adjust it manually as well (see Sonar X-PressTM Menu). Six additional Digital Readouts display information from optional-purchase accessories. These information boxes can be customized to show only the information desired (see Setup Menu Tab, Select Readouts).

Bottom Presentation

As the boat moves, the unit charts the changes in depth on the display to create a profile of the Bottom Contour. The type of bottom can be determined from the return charted on the display. A Hard Bottom such as compacted sediment or flat rock appears as a thinner line across the display. A Soft Bottom such as mud or sand appears as a thicker line across the display. Rocky Bottoms have a broken, random appearance. The sonar returns from the bottom, structure and fish can be represented as either StructureID or WhiteLine. See Sonar X-PressTM Menu: Bottom View for details on how to set the bottom view. Structure ID represents weak returns in blue and strong returns in red.
WhiteLine highlights the strongest sonar returns in white, resulting in a distinctive outline. This has the benefit of clearly defining the bottom on the display.

Sonar Zoom View

Sonar Zoom View increases the displayed resolution to separate sonar returns that are very close together, such as those caused by fish suspended close to the bottom or within structure. In Zoom View, the display is split to show a narrow slice of the full range view on the right and the zoomed view on the left. The full range view on the right also contains the Zoom Preview Box that shows what part of the full range view is shown in zoom view on the left; the Zoom Preview Box tracks the bottom in the full range view. As the depth changes, the zoomed view updates automatically to display a magnified image of the bottom. The Zoom Preview Box shows where the zoomed view is in relation to the full range view. The Zoom Level, or magnification, is displayed in the lower left corner and can be changed to suit conditions (see Sonar X-PressTM Menu: Zoom Level). Upper and Lower Zoom Depth Range numbers indicate the depth of the water which is being viewed. Digital depth is displayed in the upper left hand corner. The digital readouts in the Sonar Zoom View cannot be customized; therefore, information such as water temperature and voltage are unavailable in the Sonar Zoom View.
Depth Upper Depth Range, Full Range View Upper Depth Range, Zoom View Full Range View Zoom Preview Box

Zoomed View

Zoom Level Lower Depth Range, Zoom View
Lower Depth Range, Full Range View
200/83 kHz Split Sonar View
Split Sonar View displays sonar returns from the 83 kHz wide beam on the left side of the screen and displays sonar returns from the 200 kHz narrow beam on the right side of the screen. Depth is always displayed in the upper left hand corner. You can use the Split Sonar View to make side by side comparisons between the sonar returns from the 83 kHz wide beam and the 200 kHz narrow beam. The digital readouts in the Split Sonar View cannot be customized; therefore, information such as water temperature and voltage are unavailable in the Split Sonar View.

Save or Clear a Current Track
Save the current track: From the Navigation X-PressTM menu, select Save Current Track and press the RIGHT Cursor key. The track will remain on the display, but will change from black to gray. To remove the track completely from the display, see Edit, Delete or Hide Saved Tracks.
NOTE: When you save a track, a name is automatically assigned. The track name consists of a date/time stamp, but can be re-named later (see Edit a Saved Track).
Clear the current track: From the Navigation X-PressTM menu, select Clear Current Track and press the RIGHT Cursor key. The track will be removed from the display and discarded.
Edit, Delete or Hide Saved Tracks
Display the Tracks Submenu: From any view, press the MENU key twice to display the Main Menu System, then use the RIGHT Cursor key to select the Navigation tab. Select Tracks and press the RIGHT Cursor key to display the Tracks submenu. Edit a saved track: From the Tracks submenu, select Edit and press the RIGHT Cursor key to display the list of saved tracks. Select the track you want to edit and press the RIGHT Cursor key. When the Edit Track dialog box appears, use the Cursor keys to move between fields. In the Track Name field, the UP and DOWN Cursor keys change the letter or number. All upper and lower case letters are available, as well as digits 0-9 and some punctuation characters. You can exit the Track Name field with the LEFT and RIGHT Cursor keys or by pressing the EXIT key. Select Save and press the RIGHT Cursor key to save your changes. Delete a saved track: From the Tracks submenu, select Delete and press the RIGHT Cursor key to display the list of saved tracks. Select the track you want to delete and press the RIGHT Cursor key. You will be asked to confirm deletion before the track is actually deleted. Hide or display a saved track: From the Tracks submenu, select Visibility and press the RIGHT Cursor key to display the list of saved tracks. Select the track you want to hide or display and use the Cursor keys to select Hidden or Visible. Press the EXIT key to return to the Tracks submenu.

For example, if you are fishing in 60 feet of water but are only interested in the first 30 feet (surface to a depth of 30 feet) you should set the Lower Depth Range limit to 30. The display will show the 0 to 30 foot range, allowing you to see a more detailed view than you would see if the display went all the way to the bottom. NOTE: A minimum distance of 10 feet will be maintained between the Upper and Lower Range regardless of the manual settings entered.
To adjust the Lower Range: 1. Highlight Lower Range on the Sonar X-PressTM menu. 2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to increase or decrease the Lower Range setting. (AUTO, 10 to 1500 feet, 3 to 500 meters [International Models Only], Default = AUTO)

Side Beam Range

Side Beam Range sets the deepest range that will be displayed in the WideSide View. The range must be set manually to keep the bottom visible on the display. If the Side Beam Range is set too deep for current depth conditions the sonar information will become compressed on the display and valuable detail will be lost. A WideSide transducer must be connected to the Matrix Fishing System. Side Beam Range menu choice is available when Transducer Select is set to WideSide (see Sonar Menu Tab: Transducer Select) and can only be accessed from the WideSide view.
NOTE: The Side Beam Range requires the purchase of the WideSide transducer. You can visit our website at www.humminbird.com to order this accessory online or contact our Customer Resource Center at 1-334-687-0503.
To adjust the Side Beam Range: 1. Make sure you are in WideSide Transducer Mode and that a WideSide transducer is connected, then highlight Side Beam Range on the Sonar X-PressTM menu. 2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to increase or decrease the Side Beam Range setting. (6 - 240 feet or 2 - 80 meters [International Models Only], Default = 33 feet [10 meters])

Chart Speed

Chart Speed determines the speed at which the sonar information moves across the display, and consequently the amount of detail shown. A faster speed shows more information in the Sonar Views and is preferred by most anglers; however, the sonar information moves across the display quickly. A slower speed keeps the information on the display longer, but the bottom and fish details become compressed and may be difficult to interpret. Regardless of the Chart Speed setting, the RTS Window will update at the maximum rate possible for the depth conditions. Adjust Chart Speed to your personal preference. To adjust the Chart Speed: 1. Highlight Chart Speed on the Sonar X-PressTM menu. 2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to increase or decrease the Chart Speed setting. (1-9, Ultra, where 1 = Slow, 9 = Fast, Ultra = Fastest, Default = 4)

Bottom View

Bottom View selects the method used to represent bottom and structure on the display. Structure ID represents weak returns in blue and strong returns in red. WhiteLine highlights the strongest sonar returns in white resulting in a distinctive outline. This has the benefit of clearly defining the bottom on the display. See Bottom Presentation for more information. To adjust the Bottom View: 1. Highlight Bottom View on the Sonar X-PressTM menu. 2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the Bottom View setting. (Structure ID, WhiteLine, Default = Structure ID)

Zoom Level

(Sonar Zoom View Only)
Zoom Level sets the magnification level for the Sonar Zoom View, and is only available on the X-PressTM menu when the Sonar Zoom View is active. Use Zoom to increase the display resolution to separate sonar returns that are very close together. To adjust the Zoom Level: 1. Highlight Zoom Level on the Sonar X-Press menu. 2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the Zoom Level setting for the Sonar Zoom View. (2x, 4x, 6x, 8x, Default = 2x)
NOTE: The Zoom Preview Box tracks the bottom and cannot be moved by the user.
Navigation X-PressTM Menu

(Navigation Views Only)

The Navigation X-PressTM menu provides access to the settings most frequently used. Press the MENU key once while in the Bird's Eye View, the Chart or the Combo View to access the Navigation X-PressTM menu.
NOTE: Menu choices will vary depending on system settings, such as whether you are currently navigating.

Save Current Track

Save Current Track allows you to save the current track being displayed. After the current track is saved, a new current track is started. To Save Current Track: 1. Highlight Save Current Track on the Navigation X-PressTM menu. 2. Use the RIGHT 4-WAY Cursor Control key to initiate saving the current track. 3. The Confirm dialog box will appear. To save the current track, press the RIGHT Cursor key once more. To cancel saving the current track, press the LEFT Cursor key.

Clear Current Track

Clear Current Track allows you to clear the current track being displayed and start a new track at the present position. To Clear Current Track: 1. Highlight Clear Current Track on the Navigation X-PressTM menu. 2. Use the RIGHT 4-WAY Cursor Control key to initiate clearing the current track. 3. The Confirm dialog box will appear. To clear the current track, press the RIGHT Cursor key once more. To cancel clearing the current track, press the LEFT Cursor key.

Save Current Route

(Only When Navigating)
Save Current Route allows you to save the current route being displayed. This menu choice will only appear when you are currently navigating a route. To Save Current Route: 1. Highlight Save Current Route on the Navigation X-PressTM menu. 2. Use the RIGHT 4-WAY Cursor Control key to initiate saving the current route. 3. The Confirm dialog box will appear. To save the current route, press the RIGHT Cursor key once more. To cancel saving the current route, press the LEFT Cursor key.

Fish ID+TM

Fish ID+TM uses advanced signal processing to interpret sonar returns, and will display a Fish Symbol when very selective requirements are met. When a fish is detected, a fish icon and its depth are displayed above the return that has been classified as being a fish. Three different fish size icons represent the intensity of the sonar return, and provide an indicator of relative fish size. DualBeam PLUSTM Sonar models represent targets detected in the 200 kHz narrow beam as Orange Fish Symbols, and represent targets detected in the 83 kHz wide beam as Blue Shaded Fish Symbols.
200 kHz, Narrow Beam Orange Fish Symbols
83 kHz, Wide Beam Blue Shaded Fish Symbols (DualBeam PLUSTM Only)
When Fish ID+TM is turned off, the Matrix Fishing System shows only the raw sonar returns on the display. These returns will often result in "arches" forming on the display, indicating potential targets. Due to the transducer beam angle, the distance to a fish decreases as the fish moves into the beam, and then increases as it moves out again, creating a Fish Arch when this distance change is shown on the display. Boat speed, chart speed, and the position of the fish within the sonar beam greatly affect the shape of the arch.
Transducer Cone and Fish Arches
To turn Fish ID+TM on or off: 1. Highlight Fish ID+ on the Sonar main menu. 2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to turn the Fish ID+TM setting On or Off. (Off, On, Default = Off)

Fish Sensitivity

Fish Sensitivity adjusts the threshold of the Fish ID+TM detection algorithms. Selecting a higher setting allows weaker returns to be displayed as fish. This is useful for identifying smaller fish species or baitfish. Selecting a lower setting displays fewer fish from weak sonar returns. This is helpful when seeking larger species of fish. Fish Sensitivity is used in conjunction with Fish ID+TM. Fish ID+TM must be On for Fish Sensitivity to affect the ability of the Matrix Fishing System to identify sonar returns as fish. To change the Fish Sensitivity setting: 1. Highlight Fish Sensitivity on the Sonar main menu. 2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the Fish Sensitivity setting. (Low = 1, High = 10, Default = 5)
RTS Window sets the RTS Window to either Wide or Narrow, or turns it off in the Sonar View. The RTS Window always updates at the fastest rate possible and only displays returns that are within the transducer beam. (See Real Time Sonar (RTS) Window for more information.) To change the RTS Window setting: 1. Highlight RTS Window on the Sonar main menu. 2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the RTS Window setting. (Wide, Narrow, Off, Default = Wide)

Routes

Routes allows you to view the Routes submenu. To view the Routes Submenu: 1. Highlight Routes on the Navigation main menu. 2. Use the RIGHT 4-WAY Cursor Control keys to view the Routes submenu.

Routes Submenu

The Routes Submenu contains the following menu choices: Create allows you to create a new, empty route and add waypoints to it immediately. Edit allows you to select a previously-saved route and edit its name and the waypoints on it. Delete allows you to delete a route from a list of previously-saved routes. Travel allows you to select a previously-saved route to use as the current route; this menu setting also begins navigation on this route. Routes can be traveled in either the forward or reverse direction. Info displays information about the route, including the distance and bearing from each waypoint to the next.
View Orientation allows you to select whether the Chart and Combo Views should be drawn North-Up or Course-Up. To change the View Orientation setting: 1. Highlight View Orientation on the Navigation main menu. 2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the View Orientation setting. (North-Up, Course-Up, Default = North-Up)
NOTE: The View Orientation setting does not apply to the Bird's Eye View.

Chart Detail Level

Chart Detail Level allows you to select how much chart detail you want displayed on the Navigation Views. Basic shows land areas, ports, obstructions and restricted areas. Navigation shows navaids, landmarks, ferryways and navigation routes in addition to the Basic information. Underwater shows depth contours, fishing areas, underwater wrecks, tides and currents in addition to the Basic and Navigation information. All shows roads, buildings, railways, and other notations in addition to the Basic, Navigation and Underwater information. To change the Chart Detail Level setting: 1. Highlight Chart Detail Level on the Navigation main menu. 2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the Chart Detail Level setting. (Basic, Navigation, Underwater, All, Default = All)
NOTE: Some chart details are only available on optional-purchase MMC charts.

Map Borders

Map Borders allows you to display or hide map borders. A Map Border indicates an area which contains a different map.
To change the Map Borders setting: 1. Highlight Map Borders on the Navigation main menu. 2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the Map Borders setting. (Hidden, Visible, Default = Hidden)

NOTE: Track Min Distance works in conjunction with Trackpoint Interval. Both conditions must be met before a trackpoint is added to the current track.
To change the Track Minimum Distance setting: 1. Make sure you are in Advanced User Mode, then highlight Track Min Distance on the Navigation main menu. 2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the Track Min Distance setting. (1 to 300 feet or 1 to 100 meters [International Units Only], Default = 16 ft, 5 m)
NOTE: During slow travel or drift, setting both Trackpoint Interval and Track Min Distance to small values will allow you to increase the track resolution.

Map Datum

Map Datum allows you to change the map coordinate system used by the Matrix Fishing System to match those of a paper map. To change the Map Datum setting: 1. Make sure you are in Advanced User Mode, then highlight Map Datum on the Navigation main menu. 2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the Map Datum setting. (Default = WGS 84)

Set Simulation Position

Set Simulation Position allows you to set the position of the boat used in the Simulator. To set the Simulation Position: 1. Activate the cursor and move it to the new coordinates. 2. Make sure you are in Advanced User Mode, then highlight Set Simulation Position on the Navigation main menu. 3. Use the RIGHT 4-WAY Cursor Control key to change the Simulation Position setting.

Set Map Offset

Set Map Offset allows you to change the map offset used by the Matrix Fishing System.
NOTE: The Map Offset will be applied to all maps and not just the map that requires the correction. The Map Offset should be cleared if a different map is to be used.
To change the Map Offset setting: 1. Activate the cursor and move it location where the Map Offset will be applied. 2. Make sure you are in Advanced User Mode, then highlight Set Map Offset on the Navigation main menu. 3. Use the RIGHT 4-WAY Cursor Control key to set the Map Offset.

Clear Map Offset

Clear Map Offset allows you to clear the Map Offset. Clear Map Offset is only accessible if a Map Offset is currently active. To Clear Map Offset: 1. Make sure you are in Advanced User Mode, then highlight Clear Map Offset on the Navigation main menu. 2. Use the RIGHT 4-WAY Cursor Control key to clear the Map Offset.

Off Course Alarm

Off Course Alarm sounds when the boat has moved too far off course based on the menu setting when navigating. Off Course Alarm allows you to set how far the boat is allowed to move off course before the Off Course Alarm will sound.

Off Course Limits

Arrival Alarm Circle
To change the Off Course Alarm setting: 1. Highlight Off Course Alarm on the Alarms main menu. 2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the Off Course Alarm setting. (Off, 30 to 3000 feet, 10 to 1000 meters [International Models Only], Default = 300 ft, 100 m)

Arrival Alarm

Arrival Alarm sounds when the boat has either exceeded the distance to the destination waypoint, or has entered the Arrival Alarm Circle, based on the menu setting when navigating. Arrival Alarm allows you to set how close the boat must be to the destination waypoint before the Arrival Alarm will sound. To change the Arrival Alarm setting: 1. Highlight Arrival Alarm on the Alarms main menu. 2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the Arrival Alarm setting. (Off, 30 to 3000 feet, 10 to 1000 meters [International Models Only], Default = 150 ft, 50 m)

Drift Alarm

Drift Alarm sounds when the boat has exceeded the distance from the boats anchored position, based on the menu setting. Drift Alarm allows you to set the size of a perimeter around the boats anchored position; if the anchored boat drifts outside of that perimeter, the Drift Alarm will sound.

Drift Alarm Circle

To change the Drift Alarm setting: 1. Highlight Drift Alarm on the Alarms main menu. 2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the Drift Alarm setting. (Off, 30 to 3000 feet, 10 to 1000 meters [International Models Only], Default = Off)

Drift Alarm Perimeter

Alarm Tone
Alarm Tone selects the pitch of the alarm sound. A brief tone will be produced as you adjust the Alarm Tone so that you can select the tone that you can hear best. To change the Alarm Tone setting: 1. Highlight Alarm Tone on the Alarms main menu. 2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the Alarm Tone setting. (High, Medium, Low, Default = Medium)
From any view, press the MENU key twice to access the tabbed Main Menu System, then press the RIGHT cursor key until the Setup tab is selected.
NOTE: Menu choices will vary depending on system settings such as whether the unit is set for Advanced User mode and what accessories are attached to the unit.

Units - Depth

Units - Depth selects the units of measure for all depth-related readouts. To change the Units - Depth setting: 1. Highlight Units - Depth on the Setup menu. 2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the Units - Depth setting. (Meters [International Models Only], Feet, Fathoms; Default is Meters for International models, and Feet for Domestic models)

Heading Navigation Position Speed
Temperature Time + Date Triplog Voltage.

Default Sonar View

Customized Sonar View
To Select Readouts: 1. Make sure you are in Advanced User Mode, then highlight Select Readouts on the Setup main menu. 2. Use the RIGHT 4-WAY Cursor Control key to initiate this procedure. 3. The Select Readouts submenu will appear, showing a list of all Readouts. Use the UP or DOWN Cursor keys to select a particular Readout position, then use the RIGHT or LEFT Cursor keys to change what will be displayed at that position. (Heading, Navigation, Position, Off, Speed, Temperature, Time+Date, Triplog, Voltage)

Depth Offset

Depth Offset will adjust the digital depth readout to indicate depth from the waterline or boat's keel. Enter a positive vertical measurement from the transducer to the waterline to read the depth from the waterline. Enter a negative vertical measurement from the transducer to keel to read the depth from the keel. This menu choice is available only when in Advanced User Mode (see Setup Menu Tab: User Mode.) To change the Depth Offset setting: 1. Make sure you are in Advanced User Mode, then highlight Depth Offset on the Setup menu. 2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the Depth Offset setting. (-10.0 to +10.0 feet or -3 to 3 meters [International Models Only], Default = 0)

Temp Offset

Temp Offset will adjust the temperature readout by the amount entered. This menu choice is available only when in Advanced User Mode (see Setup Menu Tab: User Mode.) To change the Temp Offset setting: 1. Make sure you are in Advanced User Mode, then highlight Temp Offset on the Setup menu. 2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the Temp Offset setting. (-10.0 to +10.0 degrees, Default = 0)

Speed Calibration

(Advanced, with Temp/Speed Only)
Speed Calibration will adjust the speed readout by the percentage entered, and will appear in the menu if a Temp/Speed Accessory is connected and the paddlewheel has moved at least once, when the unit is in Advanced User Mode (see Setup Menu Tab: User Mode.) To change the Speed Calibration setting: 1. Make sure you are in Advanced User Mode, then highlight Speed Calibration on the Setup menu. 2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the Speed Calibration setting. (-20% to +20%, Default = 0%)

Local Time Zone

Local Time Zone selects your time zone in reference to the time reported by the GPS receiver when Time+Date is selected as a Digital Readout on the Sonar View (see Select Readouts). This menu choice is available only when in Advanced User Mode (see Setup Menu Tab: User Mode.) To change the Local Time Zone: 1. Make sure you are in Advanced User Mode, then highlight Local Time Zone on the Setup menu. 2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the Local Time Zone (Default = EST [UTC-5] - Eastern Standard Time).

Daylight Savings Time

Daylight Savings Time adjusts the time display to account for local Daylight Savings Time. Selecting On adds one hour to the time display adjusted for your local time zone. Selecting Off leaves the time display as adjusted for your local time zone. This menu choice is available only when in Advanced User Mode (see Setup Menu Tab: User Mode.) To change the Daylight Savings Time setting: 1. Make sure you are in Advanced User Mode, then highlight Daylight Savings Time on the Setup menu. 2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to turn Daylight Savings Time On or Off. (Off, On, Default = Off)

Position Format

Position Format selects the format of the latitude and longitude position display. This menu choice is available only when in Advanced User Mode (see Setup Menu Tab: User Mode.) To change the Position Format setting: 1. Make sure you are in Advanced User Mode, then highlight Position Format on the Setup menu. 2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the Position Format. (dd.ddddd, ddmm.mmm', or ddmm'ss", Default = ddmm.mmm')

Time Format

(Advanced, International Only)
Time Format changes the time format used by the unit This menu choice is available only when in Advanced User Mode (see Setup Menu Tab: User Mode.) International Models Only. Time Format selects a 12 hour or 24 hour format for the time of day displayed when Time + Date is selected as a Digital Readout on the Sonar View (see Select Readouts). To change the Time Format: 1. Make sure you are in Advanced User Mode, then highlight Time Format on the Setup menu. 2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the Time Format. (12 hour, 24 hour, Default = 12 hour)

Date Format

Date Format changes the date format used by the unit This menu choice is available only when in Advanced User Mode (see Setup Menu Tab: User Mode.) International Models Only. Date Format selects the format for the date display when Time + Date is selected as a Digital Readout on the Sonar View. (see Select Readouts). To change the Date Format: 1. Make sure you are in Advanced User Mode, then highlight Date Format on the Setup menu. 2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the Date Format. (mm/dd/yy, dd.mm.yy or yy.mm.dd, Default = mm/dd/yy)

If your Matrix Fishing System doesnt power up, use the Installation Guide that also comes with it for specific confirmation details, making sure that: the power cable is properly connected to the Matrix Fishing System control head, the power cable is wired correctly, with red to positive battery terminal and black to negative terminal or ground the fuse is operational the battery voltage of the power connector is at least 10 Volts. Correct any known problems, including removing corrosion from the battery terminals or wiring, or actually replacing the battery if necessary.
Fishing System Defaults to Simulator with a Transducer Attached
A connected and functioning transducer will cause the newly-started Matrix Fishing System to go into Normal operating mode automatically. If, when you power up the Matrix Fishing System, it goes into Simulator mode automatically, even though a transducer is already connected, this means that the control head is not detecting the transducer. Perform the following troubleshooting tasks: Using the Installation Guide that also comes with your Matrix Fishing System, check to make sure that the transducer cable is securely connected to the Matrix Fishing System. Reconnect if necessary, and power up the Matrix Fishing System again to see if this fixes the problem. Replace the non-functioning transducer with a known good transducer if available and power up the control head again. Check the transducer cable. Replace the transducer if the cable is damaged or corroded.

Display Problems

There are several main conditions or sources of possible interference that may cause problems with the quality of the information displayed on the control head. Look in the following table for some symptoms of display problems and possible solutions: Problem The control head loses power at high speeds. Possible Cause If the power output of your boats engine is unregulated, the control head may be protecting itself using its over-voltage protection feature. Make sure the input voltage does not exceed 20 Volts. The transducer position may need to be adjusted. A mix of air and water flowing around the transducer (cavitation) may be interfering with the inter-pretation of sonar data. See your Installation Guide for suggestions on adjusting the transducer position. Electrical noise from the boats engine may be interfering with sonar reception. See Finding the Cause of Noise for more information. There are no fish detected, even when you know they are in the water under the boat, or sonar readings seem weak or faulty. Sonar readings may be affected if the transducer is not positioned correctly (i.e. mounted at an angle, not straight down), or there is some kind of mechanical interference, either because it is mounted inside a hull that is too thick for proper sonar transmission, the bond between the transducer and the hull is not airtight, or because the transducer is dirty. Check with your Installation Guide for guidance on re-positioning the transducer, and make sure the transducer is clean. Low battery voltage may be affecting the power of signal transmission. Electrical noise from the boats engine may be interfering with sonar reception. See Finding the Cause of Noise for more information.

NOTE: Each accessory requires a separate purchase. You can visit our website at www.humminbird.com or contact our Customer Resource Center at 1-334-687-0503 for additional details.

Specifications

Depth Capability.... 1500 ft (500 m) Power Output... 500 Watts (RMS), 4000 Watts (Peak to Peak) Operating Frequency... 200 kHz and 83 kHz DualBeam PLUSTM Area of Coverage.... 60 @ -10 dB in 83 kHz..... 20 @ -10 dB in 200 kHz Target Separation... 2 Inches (63.5 mm) Power Requirement.... 10-20 VDC LCD..... 240V x 320H Transducer..... XHS-9-20-T Transducer Cable Length.... 20 ft (6 m)
NOTE: Product specifications and features are subject to change without notice.

Contact Humminbird

Contact the Humminbird Customer Resource Center in any of the following ways:
By Telephone (Monday - Friday 8:00 a.m. to 4:30 p.m. Central Standard Time): 334-687-0503 By e-mail (typically we respond to your e-mail within three business days): custserv@techsonic.com
For direct shipping, our address is: Techsonic Industries, Inc. Service Department 108 Maple Lane Eufaula, AL 36027 USA

doc1

FISHING ROD AND TUBE HOLDERS
RAM-114-B RAM-114-BM RAM-114-D RAM-114-DTM RAM-114-F RAM-114-FM RAM-114-R RAM-114-RM RAM-117 RAM-117B RAM-119 RAM-119-23U RAM-119B RAM-119T RAM-119-3 RAM-301-B RAM-301-D RAM-301-F RAM ROD 2000 ROD HOLDER WITH BULKHEAD MOUNT RAM ROD 2000 BULKHEAD MOUNTING BASE RAM ROD 2000 ROD HOLDER WITH DECK AND TRACK MOUNT RAM ROD 2000 DECK AND TRACK MOUNTING BASE RAM ROD 2000 ROD HOLDER WITH FLUSH MOUNT RAM ROD 2000 FLUSH MOUNT BASE RAM ROD 2000 HOLDER WITH BULKHEAD MOUNT AND RAIL MOUNT ADAPTER RAM ROD 2000 RAIL MOUNT ADAPTER KIT RAM ROD FISHING ROD HOLDER SYSTEM RAM ROD FISHING ROD HOLDER RAM TUBE FISHING ROD HOLDER RAM TUBE FISHING ROD HOLDER WITH 2 X 3 PLATE RAM TUBE WITHOUT 1 1/2" DIAMETER BALL AND BASE RAM TUBE WITH TRACK PLATE AND 1 " BALL RAM TRIPLE DECK AND TRACK BASE WITHOUT BALLS RAM TUBE 2000 ROD HOLDER WITH BULKHEAD MOUNT RAM TUBE 2000 ROD HOLDER WITH DECK AND TRACK MOUNT RAM TUBE 2000 ROD HOLDER WITH FLUSH MOUNT 22 22
PRO-PULL PROPELLER REMOVAL TOOLS
PPF-101 PPF-102 PPF-103 PPF-104 PPF-106 PPF-107 PPF-108 PPF-108A PPF-113 PPF-113-1 PPF-113-2 PPF-115 PPF-116 PPF-118 PPF-119 PPF-1/8" MAX. SHAFT DIAMETER BRUTE PROPELLER PULLER KIT WITH SHAFT SAVER BOLT 1 1/8" MAX. SHAFT DIAMETER BRUTE PROPELLER PULLER WITH SHAFT SAVER BOLT 1 1/2" MAX. SHAFT DIAMETER HEAVY-DUTY PROPELLER PULLER 2 1/2" MAX. SHAFT DIAMETER HEAVY-DUTY PROPELLER PULLER 1 1/4" - 2 1/2" 10 TON CHAIN PROPELLER PULLER 2" MAX. SHAFT DIAMETER HEAVY-DUTY PROPELLER PULLER BRONZE 6 IN 1 OUTBOARD & STERN-DRIVE PROPELLER NUT WRENCH ALUMINUM 6 IN 1 OUTBOARD & STERN-DRIVE PROPELLER NUT WRENCH 3/4" - 2" VERSATILE PROPELLER PULLER 5/8" RH/LH SCREW FOR 3/4" - 2" VERSATILE PROPELLER PULLER 3/4" SCREW FOR 3/4" - 2" VERSATILE PROPELLER PULLER OUTBOARD AND STERN-DRIVE PROPELLER PULLER 3" MAX. SHAFT DIAMETER HEAVY-DUTY PROPELLER PULLER 1 1/2" MAX. SHAFT DIAMETER BRUTE PROPELLER PULLER WITH POINTED BOLT 2" MAX. SHAFT DIAMETER BRUTE PROPELLER PULLER WITH POINTED BOLT 3/4"-NC PROPELLER NUT KIT WITH NYLOCK NUT COTTER PIN, BRASS KEY & GREASE 30 30
Ball & Swing Arm Mounts

RAM-101-G2U

Description Double socket arm mount with two round bases. Both bases have the AMPS hole pattern and a custom hardware pack is included for assembly. The mount is 7.35'' tall at maximum extension and is collapsible. Rubber ball and socket feature dampens shock and vibration. For most applications, mount will support up to ten pounds. Features

MATERIAL: Powder Coated Marine Grade Aluminum BALL SIZE: 1.5 Inch Rubber Ball COLOR: Black Powder Coat WEIGHT: 0.66 lbs

Mount Components

BASE: RAM-202-G2U ARM: RAM-201U BASE: RAM-202U
Compatible Makes & Models GARMIN FISHFINDER 250 GARMIN FISHFINDER 250C GARMIN FISHFINDER 340C GARMIN GPSMAP 178 SOUNDER GARMIN GPSMAP 178C SOUNDER GARMIN GPSMAP 292
Compatible Makes & Models GARMIN GPSMAP 298 SOUNDER GARMIN GPSMAP 392 GARMIN GPSMAP 398 SOUNDER GARMIN GPSMAP 492 GARMIN GPSMAP 498 SOUNDER

RAM-107U

Description The RAM-107 Mount is a Marine Grade Aluminum Swivel Mount with 1.5 inch C Size Ball and Socket System. The base of the mount is a 2.5 inch diameter plate designed to be permanently attached to a flat surface. The plate end of the mount connects to the underside of select Humminbird unit mounts. Features
MATERIAL: Powder Coated Marine Grade Aluminum BALL SIZE: 1.5 Inch Rubber Ball COLOR: Black Powder Coat WEIGHT: 1.4 lbs
BASE: RAM-107BU ARM: RAM-201U BASE: RAM-202U
Compatible Makes & Models HUMMINBIRD 141C HUMMINBIRD 323 HUMMINBIRD 363 COMBO HUMMINBIRD 383C COMBO HUMMINBIRD FISHFINDER 525 HUMMINBIRD FISHFINDER 535
Compatible Makes & Models HUMMINBIRD FISHFINDER 565 HUMMINBIRD FISHFINDER 585C HUMMINBIRD FISHFINDER 595C COMBO HUMMINBIRD 727 HUMMINBIRD 737 HUMMINBIRD 777C HUMMINBIRD 787C COMBO

RAM-109HSB

Description
The RAM single swing arm mount consists of a 6'' long STRAIGHT swing arm mounted on a horizontal surface mounting base. At the device mounting end of the mount is a rectangular 6.24'' x 1.98'' plate. The rectangular plate is connected to the swing arm with a RAM 1.5'' Ball and Socket System. The connection between the swing arm and the base is a bolt pivot point, and the rectangular plate and arm connection is the RAM ball and socket system. The bolt pivoting point allows a complete 360 degree rotation and the ball and socket system allows a 180 degree vertical pivot with a 360 degree rotation.

Features

MATERIAL: Powder Coated Marine Grade Aluminum BALL SIZE: 1.5 Inch Rubber Ball COLOR: Black Powder Coat WEIGHT: 1.98 lbs
(1) Base RAM-111B (1) Arm RAM-109U-G2 (1) Base RAM-109H-B

Compatible Makes & Models
GARMIN FISHFINDER 320C GARMIN GPSMAP 180 GARMIN GPSMAP 182 GARMIN GPSMAP 182C GARMIN GPSMAP 185 SOUNDER GARMIN GPSMAP 188 SOUNDER GARMIN GPSMAP 188C SOUNDER GARMIN GPSMAP 192C GARMIN GPSMAP 198C SOUNDER
Compatible Makes & Models Compatible Makes & Models C
GARMIN GPSMAP 2106 GARMIN GPSMAP 2206 GARMIN GPSMAP 230 GARMIN GPSMAP 232 GARMIN GPSMAP 235 SOUNDER GARMIN GPSMAP 238 SOUNDER GARMIN GPSMAP 3005C GARMIN GPSMAP 3006C GARMIN GPSMAP 3205 GARMIN GPSMAP 3206 LOWRANCE LCX-104C LOWRANCE LCX-110C LOWRANCE LCX-17M LOWRANCE LCX-19C LOWRANCE LCX-20C LOWRANCE LCX-25C LOWRANCE LCX-26C HD LOWRANCE LMS-332C HUMMINBIRD 947C 3D COMBO HUMMINBIRD 931C HUMMINBIRD 937C COMBO HUMMINBIRD 981C SI HUMMINBIRD 987C SI COMBO HUMMINBIRD MATRIX 97

RAM-109HU

The RAM single swing arm mount consists of a 6'' long BENT swing arm mounted on a horizontal surface mounting base. At the device mounting end of the mount is a rectangular 6.24'' x 1.98'' plate. The rectangular plate is connected to the swing arm with a pivot post. There are two (2) pivoting points on the mount. One at the swing arm and base and one at the center of the rectangular plate and the end of the swing arm. Each pivoting point allows a complete 360 degree rotation.
MATERIAL: Powder Coated Marine Grade Aluminum BALL SIZE: 1.5 Inch Rubber Ball COLOR: Black Powder Coat WEIGHT: 1.66 lbs
BASE: RAM-111BTU ARM: RAM-109-1APU BASE: RAM-109H-B
Compatible Makes & Models Compatible Makes & Models Compatible Makes & Models

RAM-109H-1U

The RAM dual swing arm mount consists of two 6'' long BENT swing arms mounted on a horizontal surface mounting base. At the device mounting end of the mount is a rectangular 6.24'' x 1.98'' plate. The rectangular plate is connected to the swing arm with a pivot post. There are three (3) pivoting points on the mount. One at the swing arm and base, one at the center where the two swing arms join and one at the center of the rectangular plate and the end of the swing arm. Each pivoting point allows a complete 360 degree rotation, making the RAM-109H-1 one of the most versatile swing arm mounts on the market today.
MATERIAL: Powder Coated Marine Grade Aluminum BALL SIZE: 1.5 Inch Rubber Ball COLOR: Black Powder Coat WEIGHT: 2.6 lbs

BASE: RAM-111BTU ARM: RAM-109-1A ARM: RAM-109-1APU BASE: RAM-109H-B

RAM-109H-2U

The RAM dual swing and socket arm mount consists of a 6'' long STRAIGHT swing arm mounted on a horizontal surface mounting base. At the device mounting end of the mount is a rectangular 6.25'' x 1.98'' plate. The rectangular plate is connected to the socket arm with a 1.5'' ball and socket system. There are three (3) pivoting points on the mount. The connection between the swing arm and the base is a bolt pivot point, and the rectangular plate to socket arm and the swing arm to socket arm connections have the RAM 1.5'' ball and socket system. The bolt pivoting point allows a complete 360 degree rotation. The dual arm ball and socket system connection allows a 180 degree vertical pivot with a 360 degree rotation while the end plate ball and socket system allows a 180 degree vertical pivot with a 360 degree rotation.
MATERIAL: Powder Coated Marine Grade Aluminum BALL SIZE: 1.5 Inch Rubber Ball COLOR: Black Powder Coat WEIGHT: 1.75 lbs
BASE: RAM-111BU ARM: RAM-201U POST: RAM-208U ARM: RAM-109-1ATPU BASE: RAM-109H-B

RAM-109VSB

The RAM single swing arm mount consists of a 6'' long STRAIGHT swing arm mounted on a vertical surface mounting base. At the device mounting end of the mount is a rectangular 6.25'' x 1.98'' plate. The rectangular plate is connected to the swing arm with a RAM 1.5'' Ball and Socket System. The connection between the swing arm and the base is a bolt pivot point, and the rectangular plate and arm connection is the RAM ball and socket system. The bolt pivoting point allows a complete 360 degree rotation and the ball and socket system allows a 180 degree vertical pivot with a 360 degree rotation.
MATERIAL: Powder Coated Marine Grade Aluminum BALL SIZE: 1.5 Inch Rubber Ball COLOR: Black Powder Coat WEIGHT: 2.55 lbs BASE: RAM-111B ARM: RAM-109U-G2 BASE: RAM-109V-B

RAM-109VU

The RAM single swing arm mount consists of a 6'' long BENT swing arm mounted on a vertical surface mounting base. At the device mounting end of the mount is a rectangular 6.24'' x 1.98'' plate. The rectangular plate is connected to the swing arm with a pivot post. There are two (2) pivoting points on the mount. One at the swing arm and base and one at the center of the rectangular plate and the end of the swing arm. Each pivoting point allows a complete 360 degree rotation.
MATERIAL: Powder Coated Marine Grade Aluminum BALL SIZE: 1.5 Inch Rubber Ball COLOR: Black Powder Coat WEIGHT: 2 lbs

MATERIAL: Powder Coated Marine Grade Aluminum BALL SIZE: 1.5 Inch Rubber Ball COLOR: Black Powder Coat WEIGHT: N/A
BASE: RAM-338U BASE: RAM-111U ARM: RAM-201U BASE: RAM-202U

RAM-137U

Description Aluminum 1.5'' Ball 2.5'' diameter Base with 3'' x 11'' Plate Mount. Features
BASE: RAM-137BU ARM: RAM-201U BASE: RAM-202U
GARMIN GPSMAP 2006 GARMIN GPSMAP 2006C GARMIN GPSMAP 2010 GARMIN GPSMAP 2010C GARMIN GPSMAP 2110 GARMIN GPSMAP 2210 GARMIN GPSMAP 3010C GARMIN GPSMAP 3210 LOWRANCE LCX-111C HD

RAM-B-101-G2U

The RAM Marine Grade Aluminum Dash Mount consists of the 1'' diameter ball and socket system with RAM Universal 2.5'' diameter Plate and connection hardware. This mount is designed to be a universal mounting solution for both RAM and non-RAM designed products. The hole pattern found on the 2.5'' Plate will connect to a large variety of third party cradles and mounts.
MATERIAL: Powder Coated Marine Grade Aluminum BALL SIZE: 1 Inch Rubber Ball COLOR: Black Powder Coat WEIGHT: N\A
BASE: RAM-B-202-G2U ARM: RAM-B-201U POST: RAM-B-202U
GARMIN FISHFINDER 120 GARMIN FISHFINDER 140 GARMIN FISHFINDER 250 GARMIN FISHFINDER 250C

RAM-B-103-GA18U

Description RAM Marine System for the Garmin 172 series. Features
MATERIAL: Powder Coated Marine Grade Aluminum BALL SIZE: 1 Inch Rubber Ball COLOR: Black Powder Coat WEIGHT: N/A
ADAPTER PLATE: RAM-B-202-GA18U ARM: RAM-B-201U BASE: RAM-B-202U
GARMIN GPSMAP 172 GARMIN GPSMAP 172c

RAM-B-107-1U

The RAM-B-107-1 Mount is a Marine Grade Aluminum Swivel Mount with 1.0 inch B Size Ball and Socket System. The base of the mount is a 2.5 inch diameter plate designed to be permanently attached to a flat surface. The plate end of the mount connects to the underside of the Humminbird Piranah MAX and Eagle Cuda unit mounts.
BASE: RAM-B-107-1BU ARM: RAM-B-201U BASE: RAM-B-202U
LOWRANCE M52I S-GPS LOWRANCE M56 S-MAP LOWRANCE M56I S-MAP LOWRANCE M68C S-MAP LOWRANCE M68C S-MAP ICEMACHINE LOWRANCE M68I S-MAP LOWRANCE X47 LOWRANCE X47EX LOWRANCE X67C
LOWRANCE X67C ICEMACHINE EAGLE CUDA 128 EAGLE CUDA 168 (EXCLUDING 168 EX) EAGLE CUDA 240 SERIES EAGLE FISHEASY 240 EAGLE FISHEASY 320 C

RAM-B-107-1U-238

The RAM-B-107-1U-238 Mount is a Marine Grade Aluminum Swivel Mount with 1.0 inch B Size Ball and Socket System. The base of the mount is a 2 7/16" X 1 5/16" inch diameter plate designed to be permanently attached to a flat surface. The plate end of the mount connects to the underside of the Humminbird Piranah MAX and Eagle Cuda unit mounts.

BASE: RAM-B-107-1BU ARM: RAM-B-201U BASE: RAM-B-238U

RAM-B-107U

The RAM-B-107 Mount is a Marine Grade Aluminum Swivel Mount with 1.0 inch B Size Ball and Socket System. The base of the mount is a 2.5 inch diameter plate designed to be permanently attached to a flat surface. The plate end of the mount connects to the underside of select Humminbird unit mounts.
MATERIAL: Powder Coated Marine Grade Aluminum BALL SIZE: 1 Inch Rubber Ball COLOR: Black Powder Coat WEIGHT: 0.68 lbs
BASE: RAM-B-107BU ARM: RAM-B-201U POST: RAM-B-202U
HUMMINBIRD 141C HUMMINBIRD 323 HUMMINBIRD 363 COMBO HUMMINBIRD 383C COMBO HUMMINBIRD FISHFINDER 525 HUMMINBIRD FISHFINDER 535 HUMMINBIRD FISHFINDER 565 HUMMINBIRD FISHFINDER 585C HUMMINBIRD FISHFINDER 595C COMBO HUMMINBIRD MATRIX 12
HUMMINBIRD MATRIX 17 HUMMINBIRD MATRIX 27 HUMMINBIRD MATRIX 37 HUMMINBIRD MATRIX 67 COMBO HUMMINBIRD MATRIX 77C HUMMINBIRD MATRIX 87C COMBO HUMMINBIRD MATRIX 97 COMBO HUMMINBIRD PIRANHAMAX 10 HUMMINBIRD PIRANHAMAX 15 HUMMINBIRD PIRANHAMAX 20

RAM-B-107U-238

Description RAM Mount for the Humminbird/Apelco diameter base swivel mount Matrix and 500 series. Features
MATERIAL: Powder Coated Marine Grade Aluminum BALL SIZE: 1 Inch Rubber Ball COLOR: Black Powder Coat WEIGHT: 0.68 lbs.
ADAPTER PLATE: RAM-B-107BU ARM: RAM-B-201U BASE: RAM-B-238U

RAM-114-B

Description RAM Rod 2000 Holder with Bulkhead Mount. Base Type Vertical Mounting Base Cradle Design Vertical mounting base has a socket for a vertical arm that extends to the ROD holder. If you require a horizontal mount, consider the RAM-114-F. Features
MATERIAL: High Strength Plastic BALL SIZE: N\A COLOR: Black WEIGHT: 1.02 lbs
HOLDER: RAM-114 BASE: RAM-114-BM

RAM-114-BM

Description RAM Rod 2000 Bulkhead Mounting Base. Part Design This base has a socket for the RAM Rod 2000 arm at 0 degrees to the base plate. If you require a horizontal mount, consider the RAM-114-FM. Features
MATERIAL: High Strength Plastic BALL SIZE: N\A COLOR: Black WEIGHT: 0.2 lbs

RAM-114-D

Description RAM Rod 2000 Holder with Deck and Track Mount. Base Type Flat Surface Mounting Base Features
MATERIAL: High Strength Plastic BALL SIZE: N\A COLOR: Black WEIGHT: 1.12 lbs
HOLDER: RAM-114 BASE: RAM-114-DTM

RAM-114-DTM

Description RAM Rod 2000 Deck and Track Mounting Base. Features
MATERIAL: High Strength Plastic BALL SIZE: N\A COLOR: Black WEIGHT: 0.44 lbs

RAM-114-F

Description RAM Rod 2000 Holder with Flush Mount. Base Type Horizontal Mounting Base Cradle Design Horizontal mounting base has a socket for a vertical arm that extends to the ROD holder. If you require a vertical mount, consider the RAM-114-B. Features

MATERIAL: High Strength Plastic BALL SIZE: N\A COLOR: Black WEIGHT: 1.21 lbs
HOLDER: RAM-114 BASE: RAM-114-FM

RAM-114-FM

Description RAM Rod 2000 Flush Mounting Base. Part Design This base has a socket for the RAM Rod 2000 arm at 90 degrees to the base plate. If you require a vertical mount, consider the RAM-114-BM. Features
MATERIAL: High Strength Plastic BALL SIZE: N\A COLOR: Black WEIGHT: 0.3 lbs

RAM-114-R

Description RAM Rod 2000 Holder with Bulkhead Mount and Rail Mount Adapter. Base Type Rail Mounting Base Features
MATERIAL: High Strength Plastic BALL SIZE: N\A COLOR: Black WEIGHT: N/A
HOLDER: RAM-114 BASE: RAM-114-BM BASE: RAM-114-RM

RAM-114-RM

Description Rail Mount Adapter for the RAM-114FM and RAM-114BM Base for RAM Rod 2000. Part Design This adapter joins to base plates with the screws provided and turns the flat base into a rail base. The adapter is a 'U' shape so it can wrap around a tube mount and the clamp by joining to the flat plate base. Features
MATERIAL: High Strength Plastic BALL SIZE: N\A COLOR: Black WEIGHT: 0.4 lbs

RAM-117

RAM-117B
Plastic RAM ROD-2000 Fishing Rod Holder with Aluminum Round 2.5'' Diameter Base Mount.
Plastic RAM ROD 2000 Fishing Rod Holder with 1.5'' Ball.
MATERIAL: High Strength Plastic BALL SIZE: 1.5 Inch Rubber Ball COLOR: Black WEIGHT: 0.61 lbs
MATERIAL: High Strength Plastic HOLDER: RAM-117U BALL SIZE: 1.5 Inch Rubber Ball ARM: RAM-201U COLOR: Black WEIGHT: 1.75 lbs

RAM-119

RAM-119-23U
Description RAM Tube Fishing Rod Holder.
This aluminum tube is design to hold the handle end of you fishing rod. It is an aluminum tube with a 1.5'' socket at the end, connected to a 2.5'' round plate with a 1.5'' Ball.
This aluminum tube is design to hold the handle end of you fishing rod. It is an aluminum tube with a 1.5'' socket at the end, connected to a 2 x 3 plate with a 1.5'' Ball.

MATERIAL: Powder Coated Marine Grade Aluminum HOLDER: RAM-119B BALL SIZE: 1.5 Inch Rubber Ball BASE: RAM-202U COLOR: Black Powder Coat WEIGHT: 1.71 lbs
MATERIAL: Powder Coated Marine Grade Aluminum HOLDER: RAM-119B BALL SIZE: 1.5 Inch Rubber Ball BASE: RAM-202U-23 COLOR: Black Powder Coat WEIGHT: 1.71 lbs

RAM-119B

RAM-119T
Description RAM Tube Fishing Rod Holder without 1 Diameter Ball and Base.
This aluminum tube is design to hold the handle end of you fishing rod. It is an aluminum tube with a 1.5'' socket at the end. It will connect to any of the RAM 1.5'' Ball accessories.
This aluminum tube is design to hold the handle end of you fishing rod. It is an aluminum tube with a 1.5'' socket at the end, connected to a track plate with a 1.5'' Ball.
MATERIAL: Powder Coated Marine Grade Aluminum BALL SIZE: 1.5 Inch Rubber Ball COLOR: Black Powder Coat WEIGHT: 1.27 lbs
MATERIAL: Powder Coated Marine Grade Aluminum BALL SIZE: 1.5 Inch Rubber Ball COLOR: Black Powder Coat

RAM-119-3

RAM-301-B
Description RAM Triple Deck and Track Base without Balls. Features
MATERIAL: Powder Coated Marine Grade Aluminum BALL SIZE: 1.5 Inch Rubber Ball COLOR: Black Powder Coat WEIGHT: N\A
Description RAM Tube 2000 Holder with Bulkhead Mount. Features
MATERIAL: High Strength Plastic BALL SIZE: N\A COLOR: Black WEIGHT: N\A

RAM-301-D

RAM-301-F
Description RAM Tube 2000 Rod Holder with Deck and Track Mount. Features
Description RAM Tube 2000 Rod Holder with Flush Mount. Features

PPF-101

Description 1 1/8" Max. Shaft Diameter Brute Propeller Puller Kit with Shaft Saver Bolt. PRO-PULL Brute models are designed to remove, 2, 3, most 4 and some 5 blade propellers on inboard shafts ranging from 3/4 - 2. They are made of high strength heat-treated alloy steel and finished with cadmium for protection. These tools have fine thread screws to enable a strong pulling force with little effort. Features Kit includes: (3/4 - 1 1/8) Shaft diameter propeller puller, a wrench for the puller and prop nut, a stainless steel cotter pin, a brass prop shaft key, a brass nylock prop nut, waterproof grease, safety lanyard and is packaged in a rustproof carrying case. Clearence required between propeller hub and strut is 1/4 minimum. Weight 6 lbs.

PPF-102

Description 1 1/8" Max. Shaft Diameter Brute Propeller Puller with Shaft Saver Bolt. PRO-PULL Brute models are designed to remove, 2, 3, most 4 and some 5 blade propellers on inboard shafts ranging from 3/4 - 2. They are made of high strength heat-treated alloy steel and finished with cadmium for protection. These tools have fine thread screws to enable a strong pulling force with little effort. Features (3/4 - 1 1/8) Shaft diameter tool only is the same propeller puller used in the PPF-101 Kit. Clearance required between propeller hub and strut is 1/4 minimum Weight 4 lbs.

PPF-103

Description 1 1/2" Max. Shaft Diameter Heavy-Duty Propeller Puller. PRO-PULL Heavy Duty models are designed to remove 2, 3, most 4 and some 5 blade propellers on inboard shafts ranging from 1 1/4 - 3. They are made of high strength heat-treated allow steel and finished with cadmium for protection. Threaded rods, washers and nuts are zinc plated steel. The forked end of the puller will fit behind the propeller hub with minimal clearance required. The shaft end of the puller has a recess to captivate and hold the propeller shaft in the center of the tool so it wont slip off while in use. Features (1 1/4 - 1 1/2) Shaft diameter propeller puller. Clearance required between propeller hub and strut is 3/4 minimum. Weight 12 lbs.

PPF-104

Description 2 1/2" Max. Shaft Diameter Heavy-Duty Propeller Puller. PRO-PULL Heavy Duty models are designed to remove 2, 3, most 4 and some 5 blade propellers on inboard shafts ranging from 1 1/4 - 3. They are made of high strength heat-treated allow steel and finished with cadmium for protection. Threaded rods, washers and nuts are zinc plated steel. The forked end of the puller will fit behind the propeller hub with minimal clearance required. The shaft end of the puller has a recess to captivate and hold the propeller shaft in the center of the tool so it wont slip off while in use. Features (2 1/8 - 2 1/2) Shaft diameter propeller puller. Clearance required between propeller hub and strut is 7/8 minimum. Weight 27 lbs.

PPF-106

Description 1 1/4" - 2 1/2" 10 Ton Chain Propeller Puller. PRO-PULL 10 Ton Chain propeller puller is designed to remove 2, 3, 4, 5 and 6 blade propellers on inboard shafts ranging from 1 1/4 - 2 1/2. Its made of high strength heat-treated allow steel and finished with cadmium for protection. The chains are grade 70 transport rated and are plated with cadmium. All bolts, nuts and threaded parts are either grade 5 or heat-treated allow steel finished with cadmium. Four propeller shaft adapters are used to set puller up for a specific shaft size and/or if propeller blades extend forward of the propeller hub. Four hooks with safety rings are used on propellers that have no clearance between the propeller hub and the strut. The chains conform to propeller blades that overlap to accomodate easy propeller removal without damage to the blades. Complete with zinc plated case hardened box wrench to operate puller a container of waterproof grease, waterproof tool box and instructions with diagrams for use. Features (1 1/4 - 2 1/2) Shaft diameter 10 Ton chain propeller puller. Net weight of tool complete with accessories and stowage box. Weight 34 lbs.

PPF-107

Description 2" Max. Shaft Diameter Heavy-Duty Propeller Puller. PRO-PULL Heavy Duty models are designed to remove 2, 3, most 4 and some 5 blade propellers on inboard shafts ranging from 1 1/4 - 3. They are made of high strength heat-treated allow steel and finished with cadmium for protection. Threaded rods, washers and nuts are zinc plated steel. The forked end of the puller will fit behind the propeller hub with minimal clearance required. The shaft end of the puller has a recess to captivate and hold the propeller shaft in the center of the tool so it wont slip off while in use. Features (1 5/8 - 2) Shaft diameter propeller puller. Clearance required between propeller hub and strut is 13/16 minimum. Weight 18 lbs.

(BRONZE)

(ALUMINUM)

PPF-108 / PPF-108A

Description Bronze/Aluminum 6 in 1 Outboard and Stern-Drive Propeller Nut Wrench. PRO-PULL Outboard and Stern-Drive 6 in 1 propeller wrench is made of solid Nibral or Marine Grade Aluminum with six tools all in one easy to use handle. It will remove and install propeller nuts, cotter pins and propeller nut keepers on the following Outboard engines: 1. Mercury 75hp & up 2. OMC 60hp & up 3. Suzuki 55hp & up 4. Mariner 75hp & up 5. Yamaha 55hp & up It will also work on all Stern-Drive engines made by: Mercury, OMC, Suzuki, Mariner, Yamaha and many others with either a 1 1/16 or 1 1/4 propeller nut. This tool comes packaged with a safety wrist strap to prevent toollose if accidentally dropped overboard. Product Numbers PPF-108: Pro-Pull 6 in 1 Bronze Wrench. PPF-108A: Pro-Pull 6 in 1 Aluminum Wrench. Weight PPF-108: 2 lbs. PPF-108A: 1 lbs.

PPF-113

Description 3/4" - 2" Versatile Propeller Puller. PRO-PULL Versatile propeller puller is designed to remove 2, 3, most 4 and some 5 blade propellers on inboard shafts ranging from 3/4 - 2. Its made of high strength heat-treated alloy steel and finished with cadmium for protection. The threaded rods, pivot pins and handle are manufactured using the finest stressproof steels available. The shaft end of the puller has a recess to captivate and hold the propeller shaft in the center of the tool so it cant slip off while in use. The offset design of the pivot pins keep the hook of the tool on the propeller hub and pulls through the center of the propeller shaft. Minimal clearance between the propeller hub and strut are required due to the unique puller design. This propeller puller requires no additional tools for operation. Features (2 1/8 - 2 1/2) Shaft diameter propeller puller. Clearance required between propeller hub and strut is 7/8 minimum. Weight 16 lbs.

PPF-113-1 / PPF-113-2

Product Numbers PPF-113-1: 5/8" RH/LH Screw For 3/4" - 2" Versatile Propeller Puller PPF-113-2: 3/4" Screw For 3/4" - 2" Versatile Propeller Puller Weight PPF-113-1: 0.8 lbs. PPF-113-2: 0.9 lbs.

PPF-113-2

PPF-113-1

PPF-115

Description Outboard and Stern-Drive Propeller Puller. PRO-PULL Outboard and Stern-Drive propeller puller is designed to remove any 2, 3, 4, 5 and 6 blade propeller. Structural components are made of heat-treated alloy steel finished with cadmium for protection. The bolt is grade 5 steel plated with cadmium. This puller will also remove any Duo-Prop. In addition this tool may also be used on many boats with inboard shafts up to 1 1/4 diameter. Comes complete with a waterproof carrying case for convenient stowage. This propeller puller requires no additional tools for operation. Features Outboard and Stern-Drive propeller puller. Net weight includes puller with all accessories. Weight 22 lbs.

PPF-116

Description 3/4" - 2" Versatile Propeller Puller. PRO-PULL Versatile propeller puller is designed to remove 2, 3, most 4 and some 5 blade propellers on inboard shafts ranging from 3/4 - 2. Its made of high strength heat-treated alloy steel and finished with cadmium for protection. The threaded rods, pivot pins and handle are manufactured using the finest stress-proof steels available. The shaft end of the puller has a recess to captivate and hold the propeller shaft in the center of the tool so it cant slip off while in use. The offset design of the pivot pins keep the hook of the tool on the propeller hub and pulls through the center of the propeller shaft. Minimal clearance between the propeller hub and strut are required due to the unique puller design. This propeller puller requires no additional tools for operation. Features (2 1/8 - 2 1/2) Shaft diameter propeller puller. Clearance required between propeller hub and strut is 7/8 minimum. Weight 16 lbs.

PPF-118

Description 1 1/2" Max. Shaft Diameter Brute Propeller Puller with Pointed Bolt. PRO-PULL Brute models are designed to remove, 2, 3, most 4 and some 5 blade propellers on inboard shafts ranging from 3/4 - 2. They are made of high strength heat-treated alloy steel and finished with cadmium for protection. These tools have fine thread screws to enable a strong pulling force with little effort. Features (1 1/4 - 1 1/2) Shaft diameter propeller puller with removable handle and safety lanyard. Clearance required between propeller hub and strut is 5/8. Weight 11 lbs.

PPF-119

Description 2" Max. Shaft Diameter Brute Propeller Puller with Pointed Bolt. PRO-PULL Brute models are designed to remove, 2, 3, most 4 and some 5 blade propellers on inboard shafts ranging from 3/4 - 2. They are made of high strength heat-treated alloy steel and finished with cadmium for protection. These tools have fine thread screws to enable a strong pulling force with little effort. Features (1 5/8 - 2) Shaft diameter propeller puller with removable handle and safety lanyard. Clearance required between propeller hub and strut is 3/4. Weight 28 lbs.

PPF-216

Description 3/4"-NC Propeller Nut Kit with Nylock Nut Cotter Pin, Brass Key and Grease.

CONTACT US

To request additional information or determine the best mounting method for your equipment, contact us through any of the following methods: National Products, Inc. Phone: Fax: Website: Email: 206-763-8361 206-763-9615 www.ram-mount.com Staff@ram-mount.com
RAM Mount products are sold only through dealers and re-sellers. To find a RAM Mount dealer near you connect to the following website address: www.ram-mount.com

 

Technical specifications

General
Product TypeChartplotter
Width9 in
Depth3 in
Height7 in
GPS System
Recommended UseMarine
GPS Functions / ServicesSpeed
Compatible GPS SoftwareNavionics Gold, Navionics HotMaps Premium
Navigation
Waypoints750
Tracks10
Tracklog Points2000
Routes50
Sonar
FeaturesTrueArch, sonar echo enhancement, Selective Fish ID+
Transducer
Transducer PresenceIncluded transducer
Transducer TypeXNT-9-20-T - dual-beam
Transducer MountTransom, in-hull
Maximum Depth1500 ft
Target Separation2.5 in
Beamwidth20/60 degrees
Operating Frequency83/200 kHz
Power Output (Peak to Peak)4000 W
Power Output (RMS)500 W
Transducer FeaturesBuilt-in temperature sensor
Built-in Display
TypeTFT
Resolution320 x 240
Diagonal Size5.6"
Display IlluminationYes
Color SupportColor
FeaturesSplit screen zoom, Real Time Sonar (RTS) window
Power
Low Voltage PowerDC 10 - 20 V
Miscellaneous
WaterproofYes
Universal Product Identifiers
BrandHumminbird
Part Number405960-1
GTIN00082324027444

 

Tags

8624 400 SX-J420 PLC-XF42 Assist Z098 EW842F VGN-FE31H GR-DV1 5450 VI Mainboard NW-E305 M-106 Yamaha SY55 CU-B50dbe8 Basses EW1080F 124700 Pioneer A400 SB-R200 WA 162 200 VOX KX-TG6021B Review 016 E DSC-W190 B Monitor ICF-C50 Dvdr3380-31 S2000HD Svart Tablet Server NWZ-S615F T2288 C1-01 Maunal LRA-850 Dh65e S RMB383 HT-DM160 DH-100 DPL950VD-DVD HTS3011 DVC845E LE26R51BD AT3705-DTV Psr-2700 PRO 410 Wizooverb W5 DXI8560 PX888 FJS1014 DEH-3100UB Schuko MD 50 Stylus 830 SX210-2008 SD-YD250 Smcwebt-G XR-C5100R XT225-2006 42LB2DE STR-DH700 32LB9RTE Singer 6011 WB14B7 HN 6135 GR-B197GVC Phone Controller Software MG32 14FX CDE-9870 TLX121 5 0 Omnia I908 EC970W AX410 HT-Z210R DC740KA FV-301 PDS4229 5000P Switch EZY-R FC-100V LE22A455c1D Alive 3 ASF2750 Explorist 200 EX2200 Autocad UF-595 KX-FPC141 BBA 2787 - 1984 EWF1028 BDV-IS1000 C F2-1000T ZWD1262W Pc Card AVR 125

 

manuel d'instructions, Guide de l'utilisateur | Manual de instrucciones, Instrucciones de uso | Bedienungsanleitung, Bedienungsanleitung | Manual de Instruções, guia do usuário | инструкция | návod na použitie, Užívateľská príručka, návod k použití | bruksanvisningen | instrukcja, podręcznik użytkownika | kullanım kılavuzu, Kullanım | kézikönyv, használati útmutató | manuale di istruzioni, istruzioni d'uso | handleiding, gebruikershandleiding

 

Sitemap

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101