IS THE SYSTEM PART OF A CLUSTER? YES. Schedule maintenance with the customer. Shut down all systems related to the cluster. Run storage test. NO. Go to step 002.
IF THE SYSTEM IS NOT PART OF A CLUSTER: v Power-off the computer and all external devices. v Check all cables and power cords. v Set all display controls to the middle position. v Power-on all external devices. v Power-on the computer. v Record any POST error messages displayed on the screen. If an error is displayed, look up the first error in the POST error codes on page 114. v Check the System Error Log. If an error was recorded by the system, see Symptom-to-FRU index on page 105. v Start the Diagnostic Programs. See Starting the diagnostic programs on page 13. v Check for the following responses: 1. One beep. 2. Readable instructions or the Main Menu. DID YOU RECEIVE BOTH OF THE CORRECT RESPONSES? NO. Find the failure symptom in Symptom-to-FRU index on page 105. YES. Run the Diagnostic Programs. If necessary, refer to Diagnostic programs and error messages on page 12. If you receive an error, go to Symptom-to-FRU index on page 105. If the diagnostics completed successfully and you still suspect a problem, see Undetermined problems on page 119.
The IBM IntelliStation E Pro computer incorporates many of the latest advances in computing technology and can be expanded and upgraded as needs change. If you have access to the Internet, you can obtain up-to-date information about the computer and other IBM computer products at http://www.ibm.com/pc/intellistation on the World Wide Web. Refer to the following illustrations for the location of the computer model and serial number labels. You will need these numbers to register your computer with IBM. Note: The illustrations in this document might differ slightly from your hardware.

Desktop model:

Serial number

Tower model:

Features and specifications for the desktop model
This section describes features and specifications.

Desktop model

The following table provides a summary of the features and specifications of the desktop model. Some features and specifications are not available on all models.
Microprocessor: Depending on model: v Intel Pentium 4 with 256 KB Level-2 cache v Intel Pentium 4 with 512 KB Level-2 cache Memory: ECC or NP, depending on model: v Minimum: 128 MB v Maximum: 1.0 GB v Type: PC133 DIMMs v Slots: two dual inline Internal drives: v Hard disk drive: IDE or SCSI v One of the following: CD-ROM: IDE DVD-ROM: IDE CD-RW: IDE Power supply: 160 watt (90-240 V ac) Expansion bays: v Two 5.25-in. bays (one CD-ROM drive installed, one hard disk drive installed) v One 3.5-in. bay (one diskette drive installed) PCI expansion slots: Three 33 MHz/32-bit low-profile slots on the system board Environment: v Air temperature: Depending on model: Computer on: 10 to 35 C (50.0 v NVIDIA Quadro2 EX LP AGP to 95.0 F). Altitude: 0 to 2133 m adapter with 32 MB video memory (6998.0 ft) v NVIDIA Quadro4 LP adapter with 64 Computer off: 10 to 43 C (50.0 MB video memory to 109.4 F). Maximum altitude: v Matrox G450 DVI LP adapter with m (6998.0 ft) MB video memory v Humidity: Computer on: 8% to 80% Integrated functions: Computer off: 8% to 80% v 10BASE-T/100BASE-TX Ethernet controller on the system board with Heat output: RJ-45 Ethernet port Approximate heat output in British v Two serial ports thermal units (Btu) per hour v One parallel port v Minimum configuration: 257 Btu (75 v Two USB ports watts) v Keyboard port v Maximum configuration: 686 Btu v Mouse port (200 watts) v Audio ports Line out Electrical input: Line in v Sine-wave input (50-60 Hz) required Mic v Input voltage low range: v Dual-channel bus mastering IDE Minimum: 90 V ac controller Maximum: 137 V ac Size and weight: v Input voltage high range: v Height: 104 mm (4.1 in.) Minimum: 180 V ac v Depth: 412 mm (16.2 in.) Maximum: 265 V ac v Width: 360 mm (14.2 in.) v Input kilovolt-amperes (kVA) v Weight: approximately 10.9 kg (24 lb) approximately: when fully configured or 6.8 kg (15.0 Minimum: 0.08 kVA lb) minimum Maximum: 0.52 kVA Video adapter: Acoustical noise emissions: v Sound power, idling: 5.1 bel maximum v Sound power, operating: 5.2 bel maximum

Workstation features

The IntelliStation E Pro takes advantage of advancements in data storage, memory, systems management, and network environments. The computer includes: v High performance accelerated graphics port (AGP) graphics The computer comes with an AGP graphics adapter installed. This high-performance adapter supports high resolutions and includes many performance-enhancing features for the operating-system environment. v Large system memory The memory bus in the computer supports up to 1.5 GB of system memory. The memory controller provides error code correction (ECC) support for up to three industry-standard PC133, 3.3V, 168-pin, 133 Megahertz (MHz), unregistered, synchronous dynamic random access memory (SDRAM) dual inline memory modules (DIMMs). v Systems-management capabilities The computer comes with features that a network administrator or file server can can use to remotely manage and control the computer. Some of the features include: Wake on LAN , Remote Administration, and System Migration Assistant. v Integrated network environment support The computer comes with an Ethernet controller on the system board. This Ethernet controller has an interface for connecting to 10-Mbps or 100-Mbps networks. The computer automatically selects between 10BASE-T and 100BASE-TX environments. The controller provides full-duplex (FDX) capability, which enables simultaneous transmission and reception of data on the Ethernet local area network (LAN).
Reliability, availability, and serviceability features
Three important computer design features are reliability, availability, and serviceability (RAS). The RAS features help to ensure the integrity of the data that is stored on the computer, the availability of the computer when you need it, and the ease with which you can diagnose and repair problems. The following is an abbreviated list of the RAS features that the computer supports. Many of these features are explained in later chapters of this publication. v Reliability features Boot block recovery Cooling fans with speed-sensing capability Error code correction (ECC) front-side buses (FSBs) ECC L2 cache and system memory Parity checking on the small computer system interface (SCSI) and peripheral component interconnect (PCI) buses Advanced configuration and power interface (ACPI) Power-on self-test (POST) Synchronous dynamic random access memory (SDRAM) with serial presence detect (SPD) v Availability features Advanced Desktop Management Interface (DMI) features Auto-restart initial program load (IPL) power supply Automatic error retry or recovery Automatic computer restart after power failure Built-in, menu-driven configuration and setup programs

Creating an IBM Enhanced Diagnostics diskette
The IBM Enhanced Diagnostics diskette is used to test hardware components on your computer. You can create an IBM Enhanced Diagnostics diskette one of three ways: v Create a diskette using Access IBM v Download a program image from the World Wide Web v Create a diskette from the Product Recovery Program Do the following to create the diagnostics diskette using Access IBM: 1. From the Access IBM menu, click Protect data. 2. Click Creating emergency diskettes. 3. Click Diagnostic diskette. 4. Follow the instructions on the screen. To create a startable IBM Enhanced Diagnostics diskette from the World Wide Web: 1. Go to http://www.ibm.com/pc/support/ on the World Wide Web. 2. Download the diagnostics file for your computer to a hard disk drive directory (not to a diskette). 3. Go to a DOS prompt and change to the directory where the file was downloaded. 4. Insert a blank high-density diskette in diskette drive A. 5. Type filename a: where filename is the name of the file you downloaded from the Web, and press Enter. The downloaded Web file is self-extracting and will be copied to the diskette. When the copy completes, store the diskette in a safe place. To create an IBM Enhanced Diagnostics diskette from The Product Recovery Program: 1. Shut down the operating system and restart the computer. 2. When the prompt, To start the Product Recovery Program, press F11 is displayed, press F11.
3. From the main menu, select System Utilities. 4. Select Create a diagnostic diskette.
Using the Enhanced diagnostics diskette
Do the following to start the IBM Enhanced Diagnostics diskette: 1. Turn off any attached devices and your computer. 2. Insert the IBM Enhanced Diagnostics diskette into the diskette drive. 3. Turn on all attached devices; then turn on your computer. 4. Follow the instructions on the screen.

Viewing the test log

The test log records data about system failures and other pertinent information. The test log will not contain any information until after the diagnostic program has run. Note: If you already are running the diagnostic program, begin with step 4. Do the following to view the test log: 1. Insert the IBM Enhanced Diagnostics diskette or the Device Drivers and IBM Enhanced Diagnostics CD. 2. Shut down your operating system and restart the computer. 3. If a user password is set, the system prompts you for it. Type the password, and press Enter. 4. Run the appropriate diagnostics program and when the Diagnostic Programs screen appears, select Utility. 5. Select View Test Log from the list that appears; then follow the instructions on the screen. 6. Save the test log to a file on a diskette or to your hard disk. Note: The system maintains the test-log data while the system is turned on. When you turn off the power to the computer, the test log is cleared.

The following configuration programs are available to configure your computer: v IBM Setup Utility program The IBM Setup Utility program is part of the basic input/output system (BIOS) code that comes with your computer. You can use this program to configure serial port assignments, change interrupt request (IRQ) settings, change the device startup sequence, set the date and time, and set passwords. v SCSISelect Utility program (some models) If your computer comes with a SCSI adapter, you can use the built-in SCSISelect Utility program to configure devices that are attached to the SCSI adapter. Use this program to change default values, resolve configuration conflicts, and perform a low-level format on a SCSI hard disk drive. v Intel Boot Agent Utility program The Intel Boot Agent Utility program is part of the BIOS code that comes with your computer. You can use this program to change network startup protocols and startup order, and to set menu wait times.
Using the IBM Setup Utility program
This section provides the instructions for starting the IBM Setup Utility program and descriptions of the menu choices that are available.
Starting the IBM Setup Utility program
The IBM Setup Utility program starts automatically when POST detects that newly installed or removed hardware is not reflected in your current configuration. A diagnostic error message is displayed. See Power-on Self Test (POST) on page 11 for details about POST and POST error codes on page 114 for information about the error messages. To start the IBM Setup Utility program: 1. Turn on the computer and watch the monitor screen. If your computer is already on when you start this procedure, you must shut down the operating
system, turn off the computer, wait a few seconds until all in-use lights go off, and restart the computer. (Do not use Ctrl+Alt+Del to restart the computer.) 2. When the message Press F1 for Setup appears in the lower-left corner of the screen during startup, press F1. (This prompt appears on the screen for only a few seconds. You must press F1 quickly.) Note: If you have set both user and administrator passwords, you must type the administrator password to access the full IBM Setup Utility menu. 3. Follow the instructions that appear on the screen. Use the left and right arrow keys to select menu choices on the menu bar at the top of the screen. To change a setting on an item, select the item, and press Enter to activate a setting selection dialogue box. Use the up and down arrow keys to select the desired setting, and press Enter again.

v Change the position of the CMOS recovery jumper. See Erasing a lost or forgotten password (clearing CMOS) on page 28. v Remove the battery and then install the battery. Administrator password: Select this choice to set an administrator password. The administrator password provides access to all choices on the IBM Setup Utility main menu. You can set, change, or delete both the administrator and user passwords and enable a user to change the user password. Attention: If you set an administrator password and then forget it, you cannot override or remove it. You must replace the system board. The following table provides a summary of the password features.
Table 7. Power-on and administrator password features Type of password User password Results v Type the password to complete the system startup. v A limited set of choices is available on the IBM Setup Utility main menu. Administrator password v No password is required to start the system. v Type the password to access the IBM Setup Utility program. v All choices are available on the IBM Setup Utility main menu. Administrator and user password v You can type either password to complete the system startup. v The administrator password provides access to all choices on the IBM Setup Utility main menu. You can set, change, or delete both the administrator and user passwords, and enable you to change the user password. v The user password provides access to a limited set of choices on the IBM Setup Utility main menu. This limited access might include changing or deleting the power-on password.
Select this choice to enable or disable system power settings. ACPI BIOS IRQ: This field controls what IRQ the Advanced Configuration and Power Interface (ACPI) uses. ACPI Standby Mode: Select which power level your computer uses in standby mode. If S1 is selected, power is maintained to all devices, but all processor activity is halted. If S3 is selected, power is maintained only for the main memory. Exit from the S3 state might not be supported by all installed adapters. APM BIOS Mode: This field controls the Advanced Power Management (APM) support to the operating system. Enable this setting when your operating system supports APM-enabled computers. When this option is set to disabled, all APM BIOS support is disabled. Power Savings: Maximum power savings conserves the greatest amount of system power. Maximum performance conserves power but optimizes the performance of the computer. To alter these settings, choose Customized. To turn off power management, choose Disabled. After Power Failure: This field controls whether the system will stay on after ac power is removed and then restored. Select Power On if you use a power strip to

Use the information in the following sections to install options in the desktop model computer.
Major components of the desktop model
The following illustration shows the locations of major components in the desktop model computer.
Adapter retaining bracket

Memory modules

Frame support bracket
Drive cages CD-ROM drive Diskette drive

System board

The following illustration identifies parts of the system board. Depending on installed options, your system board might look slightly different.
DIMM 2 Microprocessor (J10TD2) DIMM 1

AGP (J5E1)

PCI 1 PCI 2 PCI 3

Battery SCSI LED (J35)

System board internal cable connectors
The following illustration identifies system board connectors for internal cables.
Fan 3 support bracket assembly fan (J3) Fan 2 microprocessor fan sink (J19)

Main power (J10K1)

Diskette drive
Primary IDE (PRI IDE) Secondary IDE (SEC IDE)
Microprocessor power (J3H1)

SCSI LED (J35)

System board external connectors
The following illustration identifies system board connectors for external devices.

Keyboard Mouse USB ports

Parallel Serial ports

Ethernet Audio

CMOS recovery jumper
The following illustration identifies the CMOS recovery jumper on the system board.
The CMOS recovery jumper can be used to clear CMOS memory in the event you lose the user password. See Erasing a lost or forgotten password (clearing CMOS) on page 28 for information on how to use the CMOS recovery jumper. This jumper is also used to recover from a BIOS failure. See Recovering from a POST/BIOS update failure on page 29.
Installing options in a desktop model
This section provides instructions for installing options in a desktop model.

Removing the cover

To remove the cover from the desktop model computer, do the following: 1. Review the information in Before you begin on page 41 and Safety information on page 131. 2. Turn off the computer and all attached devices. 3. Disconnect all external cables and power cords.
4. Press the buttons on either side of the computer cover and lift the cover from the computer.
To replace the cover, see Replacing the cover on page 56.
Removing the frame support bracket
You must remove the frame support bracket to access many of the components of the desktop model computer. To remove the frame support bracket, perform the following steps: 1. Pivot the drive cages until the pivot locks catch the front of the desktop chassis, holding the drive cages in place. 2. Lift the frame support bracket out of the computer.

Attention: Be certain that the adapter is correctly seated in the expansion slot before you turn on the computer. Incomplete installation of an adapter might damage the system board or the adapter.

Expansion slot cover

Rear adapter retention bracket Adapter Front adapter retention bracket
9. Connect required cables to the adapter. Route cables so that they do not block the flow of air from the fans. 10. If you have another adapter to install, repeat steps 1 on page 67 through 9. If you have another option to install, do so now. 11. If you have installed a full-length adapter, rotate the front adapter support bracket to the closed (locked) position. 12. Reinstall the rear adapter support bracket; then rotate the bracket to the closed (locked) position. Note: The rear retaining bracket rests against the computer cover. You might find it easier to lay the computer on its side to replace the cover. 13. Replace the support bracket. 14. Replace the side cover, see Replacing the cover on page 77 for details. 15. Reconnect the external cables and power cords; then turn on the attached devices and the computer. SCSI adapter installation: Some models do not come with SCSI adapters. Do the following to install an optional SCSI adapter: 1. If you do not have a preinstalled SCSI adapter, complete steps 1 on page 67 through 9 of Adapter installation on page 66. 2. Connect the SCSI signal cable to the adapter and one or more of the signal cable connectors to the rear of the SCSI devices. 3. Connect the SCSI activity indicator cable to the adapter and to the SCSI LED connector (J35) on the system board. See System board on page 43 for the
4. If you have other adapters or options to install or remove, do so now. 5. Rotate the front adapter-support bracket to the closed (locked) position. 6. Reinstall the rear adapter-support bracket; then rotate it to the closed (locked) position. 7. Replace the support bracket. 8. Replace the cover, see Replacing the cover on page 77 for details. 9. Reconnect the external cables and power cords; then turn on the attached devices and the computer.

6. Touch the static-protective bag containing the drive to any unpainted metal surface on the computer; then remove the drive from the bag and place it on a static-protective surface. 7. Set any jumpers or switches on the drive according to the documentation that comes with the drive. 8. You might find it easier to install the new drive into the appropriate opening on the front, and then attach the cables. 9. If you are installing a 5.25-in. drive in bay 2, push the drive into the bay; then use the two screws to attach the drive to the drive cage. 10. If you are installing a 3.5-in. drive in bay 2, you must attach the 5.25-in conversion kit, supplied with the option, to the 3.5-in. drive.
Note: You can install only a 3.5-in. device in bay 4.
11. If the drive is an IDE device, connect one end of the IDE signal cable into the back of the drive and the other end of the cable into the IDE connector on the system board. For the location of the IDE connectors, see System board internal cable connectors on page 44. If the drive is a SCSI device, connect one end of the SCSI signal cable into the back of the drive and the other end of the cable into the 68-pin connector on the SCSI adapter. Note: Route the signal cable so that it does not block the air flow to the rear of the drives or over the microprocessor. 12. Connect the power cable to the back of the drive. The connectors are keyed and can be inserted only one way. 13. If you have other options to install or remove, do so now. 14. Replace the support bracket. 15. Replace the side cover, see Replacing the cover on page 77 for details. 16. Reconnect the external cables and power cords; then turn on the attached devices and the computer. Bay 5, 6 or 7 installation: Bays 5, 6, and 7 are in the drive cage. The drive cage is located just above the front adapter-support bracket. Note: You might find it useful to work with the computer laying on its side. To install a drive in bay 5, 6, or 7, do the following: 1. Read the information in Preinstallation steps on page 70. 2. Turn off the computer and all attached devices. Disconnect all external cables and power cords; then remove the cover. See Side cover removal on page 63 for details.
3. Remove the support bracket. 4. If the computer has hard disk drives preinstalled in the drive cage, disconnect the power and signal cables from the rear of the drives. 5. Grasp the drive cage and rotate the cage out (middle view) of the computer until it locks into place with the drive-cage retention tab. The open ends of the drive slots and installed drives will face you. Note: Ensure that the drive cage locks into place over the drive-cage retention tab by pressing the drive cage all the way up. 6. Attach the guide rails to the side of the drive using the screws and blue rails provided in the drive cage. 7. Slide the drive into the drive cage until the plastic tabs on the drive guide rails lock into place in the drive cage. Note: Clear any cables that might impede the replacement of the drive cage. 8. Lift the drive cage up, and press in on the drive-cage release tab; then rotate the cage back into the computer (right view).

9. Connect the power and signal cables to the rear of each drive. Note: Route the signal cable so that it does not block the air flow to the rear of the drives or over the microprocessor. 10. If you have other options to install or remove, do so now. 11. Replace the support bracket. 12. Replace the side cover, see Replacing the cover on page 77 for details. 13. Reconnect the external cables and power cords; then turn on the attached devices and the computer. Power and signal cables for internal drives: The computer uses cables to connect IDE and SCSI devices to the power supply and to the system board. The following cables are provided: v Four-wire power cables connect the drives to the power supply. At the end of these cables are plastic connectors that attach to different drives; these connectors vary in size. Also, certain power cables attach to the system board. v Flat signal cables, also called ribbon cables, connect IDE, SCSI, and diskette drives to the system board. Two or three sizes of ribbon cables come with the computer. The wider IDE signal cable has two or three connectors. - If the cable has three connectors, one of these connectors is attached to the drive, one is a spare, and the third attaches to the primary or secondary IDE connector on the system board.
- If the cable has two connectors, one of these connectors is attached to the hard disk drive, and the other attaches to the primary or secondary IDE connector on the system board. Note: The CD-ROM drive is attached to an ATA 66 signal cable. ATA 66 signal cables are color-coded. The blue connector attaches to the system board. The black connector attaches to the primary device. The gray middle connector attaches to the secondary device. If you are installing a hard disk drive, you must change the switch or jumper setting on the CD-ROM drive to secondary and change the connector used for the CD-ROM drive to the gray middle connector. The narrower signal cable has two connectors, one to attach to the diskette drive, and the other to attach to the connector (FDD1) on the system board. If the computer comes with a SCSI adapter and SCSI hard disk drive, the following cables can be used to attach SCSI devices to the SCSI host adapter: - An Ultra160 twisted ribbon cable connects the internal Ultra160 SCSI hard disk drive to the SCSI connector on the SCSI adapter. This cable has five additional connectors for attaching more internal SCSI devices. - A round SCSI cable connects external SCSI devices to the SCSI adapter so that you can add external SCSI devices. For more information about connecting SCSI devices, see the SCSI documentation on the Software Selections CD that comes with the computer. Note: To locate connectors on the system board, see System board internal cable connectors on page 44. Review the following information before connecting power and signal cables to internal drives: v The drives that are preinstalled in the computer come with power and signal cables attached. If you replace any drives, it is important to remember which cable is attached to which drive. v When you install a drive, ensure that the drive connector at the end of the signal cable is connected to the drive and that the drive connector at the other end is connected to the system board. This reduces electronic noise from the computer. v If two IDE devices are used on a single cable, one must be designated as the primary device and the other as the secondary device; otherwise, the computer might not recognize some of the IDE devices. The primary and secondary designation is determined by switch or jumper settings on each IDE device. v If two IDE devices are on a single cable, and only one is a hard disk drive, the hard disk drive must be set as a primary device. v If you have only one IDE device on a cable, it must be set as a primary device.

6. Reconnect the external cables and power cords, turn on the attached devices, and then turn on the computer.
Do the following to replace the cover of the tower model: Note: If you removed the support bracket, reinstall it before you replace the cover. See Support bracket removal on page 64 for details. 1. Clear any cables that might impede the replacement of the cover. 2. Install the side cover by placing it into position on the computer. Be certain the notches on the underside of the cover match up to the holes along the sides of the computer. Press down on the cover release latch button as you close the cover release latch to lock the cover.
3. If you have not done so already, make sure that the two front stabilizing feet are rotated outward so that they properly support the computer. Rotate each individual foot outward 90 degrees. 4. Reconnect the external cables and power cords to the computer; then connect the power cords to electrical outlets. 5. Turn on the attached devices; then turn on the computer.
Connecting external options
You can connect a number of optional external devices to the connectors on the rear and front of the computer. If the computer comes with a SCSI adapter installed, you can attach a SCSI storage expansion enclosure to the computer. To attach an external device: 1. Read Before you begin on page 41, review the safety precautions listed in Statement 1 and Statement 5 in Safety notices (multi-lingual translations) on page 135, and read the documentation that comes with the options. 2. Be sure that the computer and all attached devices are turned off. 3. Follow the instructions that come with the option to prepare it for installation and to connect it to the computer.
Note: If you are attaching a SCSI device, see Ultra160 SCSI connector on page 83 for SCSI ID and cabling information.
Input/output connector locations
The following illustrations show the input/output connectors and the expansion slots on the rear of the computer.
Mouse USB 1 Parallel Line out Line in

Keyboard USB 2

Serial 1 Serial 2

Ethernet

Microphone

Power cord connector

Power cord connector Mouse Keyboard USB 1 USB 2 Parallel Serial 1 Serial 2 Ethernet

4. Press the two fan retention latches until the fan pops free and gently pull the fan out of the adapter guide, making sure the cable comes free smoothly. 5. To install the adapter fan, reverse the previous steps. Note: Guide the fan cable through the cutout in the adapter guide before inserting the fan.

Adapter guide

To remove the adapter guide, do the following:
1. Power-off the computer and remove external cables. 2. Remove the cover and support bracket (see Side cover removal on page 63 and Support bracket removal on page 64). 3. Remove the front bezel (see Bezel on page 94). 4. Disconnect all adapter cards from the system board and remove them from the computer (see Adapter installation on page 66).
5. Push inward on the two tabs on the left and push them toward the inside of the computer until they clear the notches; then, the three tabs on the right will come away from the chassis. 6. Pull the adapter guide away from the chassis. 7. To install the adapter guide, reverse the previous steps. Note: When installing a new adapter guide, be sure to transfer any existing adapter fan (see Adapter fan on page 92); not all models are configured with this fan.
1. Power-off the computer and remove external cables. 2. Remove the cover and support bracket (see Side cover removal on page 63 and Support bracket removal on page 64).
3. Disconnect all adapter cards from the system board and remove them from the computer (see Adapter installation on page 66).
4. Pull the adapter retainer away from the chassis. 5. To install the adapter retainer, reverse the previous steps.
To remove the main bezel on the tower model, do the following: 1. Remove the side cover (see Side cover removal on page 63). 2. Push the blue bezel release latch, located on the inside roof of the tower chassis. The bezel will detach from the chassis. 3. To install the bezel, align the tabs at the bottom of the bezel with the slots in the lower front of the chassis; then press the top of the bezel against the chassis until it clicks into place.

Bezel release latch

Note: This illustration is for reference purposes only; your hardware may differ.
To remove the bezel release latch, do the following: 1. Power-off the workstation, if it is on. 2. 3. 4. 5. Unplug the workstation. Remove the cover (see Side cover removal on page 63). Remove the front bezel (see Bezel on page 94). Press down on the tab.
6. From the underside, grasp the bezel release latch in the center and gently pull it back and away from the workstation.
To remove the rear fan on the tower model, do the following:
4. Use side cutters to sever the fans four rubber extensions on the outside of the chassis.
5. Pull the fan away from the chassis. 6. To install the rear fan, reverse the previous steps. Note: After guiding the four rubber extensions through the apertures on the chassis, use needle-nosed pliers to pull the extensions firmly through.

System, Type 6214

This parts listing supports Type 6214 models 10x, 20x, 23x, 30x, 33x, 40x, 41x, 43x, 45x, 46x, 48x, 50x, 51x, 53x, 55x, 56x, 58x, 77x, 88x, 91x, 96x, A0x, B0x, B3G, C0x, C3G, C3x, D7G, F0G, F1G, F3G, E8G, G0G, G1G, G3G.
System (IntelliStation E Pro Type 6214, Models 10x, 1PU, 20x, 23x, 2PU, 30x, 33x, 3PU, 40x, 41x, 43x, 4PU, 50x, 51x, 53x, 5PU, 77x, 88x, 91x, A0X, B0X, B3G, C0X, C3G, D7G, E8G, F0G, F1G, F3G, G0G, G1G, G3G) Cover, side/top (All models) 48X CDROM - primary (All models) 48X CD-ROM drive, alternate (All models) 48X CD-ROM drive, alternate (All models) 48X CD-ROM drive, alternate (All models) Shield, 5.25 EMC (All models) Floppy disk drive, primary (All models) Floppy disk drive, secondary (All models) Front bezel (All models) Bezel door (All models) Perforated panel (All models) Kit, power button (All models) System feet, kit (All models) Feet, snap-in (4) (All models) Speaker (All models) Cage, DASD rotating (All models) Guide, card (All models) Retainer, I/O card (All models) Lock/key assembly (All models) Door assembly (All models) PCI extender card (All models) Power supply (All models) Fansink, P4 (1.3 - 1.8GHZ) (Models 10x, 1PU, 20x, 2PU, 77x, 88x, A0X, B0X, B3G, D7G, E8G) Fansink, P4 (1.9GHz and higher) (Models 30x, 33x, 3PU, 40x, 41x ,43x, 45x, 46x, 48x, 4PU, 50x, 51x, 53x, 55x, 56x, 58x, 5PU, 91x , 96x, C0x, C3X, F0G, F1G, F3G, G0G, G1G, G3G Processor, P4 400/1600-256k D0 (Models 10x, 77x, A0X, D7G) Processor, P4 400/1800-256k D0 (Models 20x, 23x, 2PU, 88x, B0X, B3G, E8G) Processor, P4 400/2000-256k (Models 30x, 33x, 3PU, C0X, C3G) Processor, P4 400/2000-512k (Models 40x, 41x, 43x, 4PU, 91x, F0G, F1G, F3G) Processor, P4 400/2200-512k (Models 50x, 51x, 53x, 5PU, G0G, G1G, G3G) System board, w/o POV 1.8 Processor and below (Models 10x, 1PU, 20x, 23x, 2PU, 30x, 33x, 77x, 88x, A0X, B0X, D7G, E8G) System board, w/o POV 2.0 Processor and above (Models 30x, 33x, 3PU, C0X, C3G, 40x, 41x, 43x, 4PU, 50x, 51x, 53x, 5PU, 91x, F0G, F1G, F3G, G0G, G1G, G3G) Memory, 128MB, PC 133 CL2 ECC SDRAM (Models 10x, 20x, 23x, 30x, 1PU, 2PU, 3PU, 4PU, 5PU, 91x) Memory, 256MB, PC 133 CL2 ECC SDRAM (Model 33x, 40x, 41x, 43x, 50x, 51x, 53x, F0G, F1G, F3G, G0G, G1G, G3G) Memory, 128MB, NP (Models 77x, 88x, D7G, E8G) Fan, fixed speed, dual bearing 80mm (primary) (All models) Fan, fixed speed (alternate) (All models) Bracket, support (All models) Bezel kit (All models) Shield, 3.5 EMC (All models) Plate, EMC (All models) Shield, system board EMC (All models) Kit, USB blank bezel (All models) Panel, power (All models) Panel, control (All models) Retention module, heatsink (All models)