IC-F22SR_2.qxd

03.5.29 14:11

Page 1 (1,1)

New master

INSTRUCTION MANUAL

PMR446 FM TRANSCEIVER

iF22SR

Page 2 (1,1)

FOREWORD

Thank you for purchasing the IC-F22SR PMR446 FM transceiver. This PMR FM transceiver meets the European PMR446 specication. This transceiver is designed for those who require top-grade quality, performance and outstanding reliability under the most demanding conditions.

FEATURES

G Free of user-license and applications G All 8 PMR channels and Auto Scan channel are available G 52 convenient CTCSS tone channels G 83 convenient DTCS tone channels also available G Rugged construction G 500 mW (ERP) High output power
Icom, Icom Inc. and the logo are registered trademarks of Icom Incorporated (Japan) in the United states, the United Kingdom, Germany, France, Spain, Russia and/or other countries.

Page 3 (1,1)

I 2 types of built-in Code Squelch Systems:
CTCSS; Continuous Tone Coded Squelch System DTCS; Digital Tone Code Squelch
CTCSS* and DTCS* encoder/decoder are standard, providing quiet stand-by. Audio (voice) signals are output only when a signal with a matched CTCSS or DTCS tone signal is received very helpful for group communications. (pgs. 14, 28) *Select one of CTCSS or DTCS for your convenience.
I 2 types of Ring function
The Smart-Ring* function and the Call-Ring function are available for smart and simple station calls providing a telephonestyle ring when called. 16 different ringing tones are available. (pgs. 1920) *Smart-Ring function available only when all of your group station use the same CTCSS tone code on the same operating channel.

SUPPLIED ACCESSORIES

Belt clip 1 BC-146* (Regular charger) 1 set (*Depends on version)
D Attach or detach the belt clip to the transceiver as illustrated below.

Page 4 (1,1)

IMPORTANT
READ ALL INSTRUCTIONS carefully and completely
before using the transceiver.
SAVE THIS INSTRUCTION MANUALThis instruction
manual contains important operating instructions for the IC-F22SR PMR446 FM transceiver.

CAUTIONS

R WARNING! NEVER hold the transceiver so that the antenna is very close to, or touching exposed parts of the body, especially the face or eyes, while transmitting. The transceiver will perform best if the microphone is 5 to 10 cm away from the lips and the transceiver is vertical.
R WARNING! NEVER operate the transceiver with a headset or other audio accessories at high volume levels. DO NOT push the PTT when not actually desiring to transmit. DO NOT modify the transceiver for any reason. AVOID using or placing the transceiver in direct sunlight or in
areas with temperatures below 25C or above +55C. In an extreme low temperature environment (around 25C), the capacity of Alkaline or dry cell batteries may exhaust quickly. In such case, we recommend to replace the batteries, when the Low Battery warning appears during transmission. The use of non-Icom battery packs/chargers may impair transceiver performance and invalidate the warranty. iii

Page 5 (1,1)

TABLE OF CONTENTS
FOREWORD i FEATURES iii SUPPLIED ACCESSORIES ii IMPORTANT iii CAUTIONS iii TABLE OF CONTENTS iv 1 PANEL DESCRIPTION 13 Switches, controls, keys and connectors 12 LED indicator BATTERY PACKS 410 Battery pack replacement 4 Battery cautions 5 Battery charging 6 Charging NOTE 9 Battery case (Option) BASIC OPERATION 1118 Receiving and transmitting 11 Setting squelch level 13 Auto scan function 13 Setting the group code number RING FUNCTION 1920 Smart-Ring 19 Call-Ring OTHER FUNCTIONS 2123 Monitor audible function 21 Time-Out Timer 21 Power save function 22 Low battery indication 22 Optional HM-75A functions SPECIFICATIONS OPTIONS GLOSSARY CE 2930 DECLARATION OF CONFORMITY 30

Page 6 (1,1)

PANEL DESCRIPTION
Switches, controls, keys and connectors
q [CH] selector w [VOL/ POWER] e [S-Ring /C-Ring] key r [PTT] t [MONI] key Antenna y TX/RX Indicator LED u External [SP]/[MIC] jack (see below) Speaker MIC
u External [SP]/[MIC] jack

Ext. MIC.

SP MIC

Ext. SP 1

Page 7 (1,1)
q CHANNEL SELECTOR [CH] Rotate the selector to select the desired channel number 1 to 15. (pgs. 11, 12) Select the Auto Scan channel No.16. (p. 13) Select the Call-Ring melody. (p. 19) w VOLUME/POWER CONTROL [VOL/POWER] Rotate the [VOL/POWER] clockwise to turn the power ON/OFF. A long power ON beep emits when turning the power ON. Rotate clockwise to increase and counterclockwise to decrease the audio volume. e SMART-RING/CALL-RING KEY [S-Ring/C-Ring] Push to send a Smart-Ring call. (p. 19) Push and hold to send a Call-Ring. (p. 19) r PTT SWITCH [PTT] Push and hold to transmit; release to receive. t MONITOR KEY [MONI] Push and hold to open the noise/tone squelch. Push to turn the tone squelch ON. y TX/RX INDICATOR LED [LED] Lights red while transmitting. Lights green while receiving a signal, or squelch is open. Lights orange while sending/receiving a Smart-Ring call. (p. 19) Indicates the Low-battery condition. (p. 3) u EXTERNAL SPEAKER AND MICROPHONE JACKS [SP]/[MIC] Connects an optional speaker-microphone such as HM-75A. (p. 23)

Page 8 (1,1)

LED indicator
The TX/RX indicator LED indicates information in several ways as follows; (Ref.; R=Red, G=Green, O=Orange) [Brink patterns] TX: Turns Red while transmitting a signal.
RX (Busy): Turns Green while receiving a signal.
Smart-Ring: Calling or answering back the Smart-Ring now.
Fast/Slow scan: CH scanning or CTCSS FIND is functioning now.
Low BATT1: You should charge the battery. (blinks slowly)
Low BATT2: You must charge the battery. (blinks fast)

R R R R

TX low BATT1: Low BATT1 was detected during TX mode.
TX low BATT2: Low BATT2 was detected during TX mode.
CAUTION: Low BATT3: If you did not charge the battery after Low BATT2 warning has appeared, the Low BATT3 warning beep emits for 15 sec. then the power turns OFF automatically.

Page 9 (1,1)

BATTERY PACKS

Battery pack replacement

Before replacing the battery pack, the volume control MUST be rotated fully counterclockwise, until a click is heard, to turn the power OFF. Push the battery release forward, then pull the battery pack upward with the transceiver facing you.

D BATTERY PACKS

Charging period Battery Voltage Capacity pack BC-146 BC-144, BC-119 or BC-121 Operating period*
Battery case for AA BP-208 (R6) 6 alkaline BP-209 BP-210 BP-222 7.2 V 7.2 V 7.2 V 1100 mAh 1650 mAh 12 hrs 18.5 hrs 1.5 hrs 2 hrs 14.5 hrs 21.5 hrs

600 6.5 hrs 1 hr 8 hrs mAh * Operating periods are calculated under the following conditions; Tx : Rx : standby =5 : 5 : 90 Operating period depends on the alkaline cells used. (BP-208 only)

Page 10 (1,1)

Battery cautions
CAUTION! NEVER short the terminals of the battery pack (or charging terminals of the transceiver). Also, current may ow into nearby metal objects such as a necklace, so be careful when placing battery packs (or the transceiver) in handbags, etc. Simply carrying with or placing near metal objects such as a necklace, etc. causes shorting. This will damage not only the battery pack, but also the transceiver. NEVER incinerate used battery packs. Internal battery gas may cause an explosion. NEVER immerse the battery pack in water. If the battery pack becomes wet, be sure to wipe it dry BEFORE attaching it to the transceiver. Clean the battery terminals to avoid rust or miss contact. Keep battery contacts clean. Its a good idea to clean battery terminals once a week. If your battery pack seems to have no capacity even after being charged, completely discharge it, then fully charge the battery pack again. If the battery pack still does not retain a charge (or only very little charge), a new battery pack must be purchased.

Page 11 (1,1)

Battery charging
D Regular charging with the BC-146 The supplied* BC-146 provides regular charging of optional battery pack with/ without transceiver. (*depends on version) D Spacer combination. Especially when charging the battery with the transceiver; Be sure to attach the spacer (Spacer B/C) to the adaptor (Spacer A) with the orientation as follows. Attach the spacer (Spacer B/C) to the adaptor with the orientation of the stamp pointing up.
Check orientation Spacer A and

Spacer B/C

NOTE: Push the notch carefully when removing the spacer from the adaptor.

Page 12 (1,1)

D Regular charging with the BC-146 (continued) First insert the spacer in to the BC-146, then insert the battery or the transceiver. Be sure to check orientation and the spacer combination. Avoid overchargingBatteries must be removed from the charger to stop charging. Batteries should not be charged for more than 24 hours.

Turn power OFF BP-209, BP-210 or BP-222 only

AC adaptor

Check orientation*

Charging indicator

*Viewable stamps of the spacer may differ according to the spacer combination. See p. 6 for details.

Page 13 (1,1)

D Rapid charging with the BC-121N+AD-101 The optional BC-121N allows up to 6 battery packs to be charged simultaneously. The following are additionally required. Six AD-101 An AC adaptor (may be supplied with the BC-121N depending on version).

Turn power OFF.

AC adaptor (purchased separately)
Charge indicator (each indicator functions independently)
D Rapid charging with the BC-144+AD-99 The optional BC-144 provides rapid charging of optional battery packs. The following are additionally required: One AD-99 (depends on version). An AC adaptor (may be supplied with the BC-144 depending on version).
Check orientation for correct charging. (Insert together with charging adaptor.)*

BC-144

Page 14 (1,1)

Charging NOTE

Prior to using the transceiver for the rst time, the battery pack must be fully charged for optimum life and operation. Recommended temperature range for charging: +10C to +40C. Use the supplied charger or optional charger (BC-119N/BC121N/BC-144 for rapid charging, BC-146 for regular charging) only. NEVER use other manufacturers chargers. The optional BP-209, BP-210 or BP-222 battery packs include rechargeable Ni-Cd (Ni-MH: BP-210) batteries and can be charged approx. 300 times. Charge the battery pack before rst operating the transceiver or when the battery pack becomes exhausted. If you want to charge the battery pack more than 300 times, the following points should be observed: Avoid overchargingbatteries must be removed from the charger to stop charging. Batteries should not be charged for more than 24 hours. Use the battery until it becomes almost completely exhausted under normal conditions. D Battery pack life When the operating period becomes extremely short even after charging the battery pack fully, a new battery pack is needed.
NOTE for the rapid chargers : The charger rapidly charges a battery pack to a specied level, not a completed level, to prevent overcharging. Leave the battery pack in the charger for a few more hours (up to 15 hours; depending on battery condition) after the LED indicator turns green, to charge the battery completely. 9

Page 15 (1,1)

Battery case (Option)
When using a BP-208 OPTIONAL BATTERY CASE attached to the transceiver, install 6 AA (R6) size alkaline batteries as illustrated below.
D CAUTIONS Use ALKALINE batteries only. Make sure all battery cells are the same brand, type and capacity. Never mix old and new batteries. Either of the above may cause a fire hazard or damage the transceiver, if ignored. Never incinerate used battery cells since internal battery gas may cause them to rupture. Never expose a detached battery case to water. If the battery case gets wet, be sure to wipe it dry before using it.

Page 16 (1,1)

BASIC OPERATION
Receiving and transmitting
CHARGE the battery pack before rst operating the transceiver. The transceiver has been pre-programmed with all the PMR frequency channels and CTCSS tone codes as a default. The CTCSS tone number can be changed if required. Receiving: q Rotate the [VOL] knob clockwise to [VOL /POWER] turn the power ON. w Rotate the [CH] selector to select the [S-Ring /C-Ring] desired operating channel. Setting the your group code number [PTT] if required. (pgs. 1416) e Listen for a transmission and adjust [MONI] [VOL] to a comfortable listening level. *microphone [LED] turns to green, when the received signal contains same CTCSS or DTCS code number. When no transmission is heard, push and hold [MONI] while adjusting [VOL]. The transceiver is now set to receive desired calls on the selected channel. Transmitting: Wait for the channel to become clear to avoid interference. r While pushing and holding [PTT], speak into the microphone at a normal voice level. [LED] turns to red. t Release [PTT] to return to receive. *IMPORTANT: To maximize the readability of your transmitted signal, pause a few sec. after pushing [PTT], hold the microphone 10 to 15 cm from your mouth and speak at a normal voice level.

[CH selector]

Page 17 (1,1)
Frequency channel/CTCSS tone list (default)
Channel No.1 No.2 No.3 No.4 No.5 No.6 No.7 No.8 No.9 No.10 No.11 No.12 No.13 No.14 No.15 No.16

RX/TX Freq. (MHz)*1

CH spacing Narrow Narrow Narrow Narrow Narrow Narrow Narrow Narrow Narrow Narrow Narrow Narrow Narrow Narrow Narrow ------
Tone (Hz)*2 NO NO NO 107.2 110.9 114.8 118.8 123.0 127.3 131.8 136.5 141.3 146.2 151.4 156.7 ------
446.00625 446.01875 446.03125 446.04375 446.05625 446.06875 446.08125 446.09375 446.00625 446.01875 446.03125 446.04375 446.05625 446.06875 446.08125 Auto Scan
*1: All operating channel frequencies are xed. *2: CTCSS tone frequencies can be programmed by you. You can use DTCS (Digital Tone Code Squelch) instead of CTCSS. (p. 17)

Page 18 (1,1)

Setting squelch level
The squelch circuit mutes the received audio signal depending on the signal strength. q While pushing and holding [PTT] and [MONI], turn the [VOL transceivers power ON to /POWER] enter the squelch adjustment [S-Ring mode. /C-Ring] w Push [S-Ring/C-Ring] to increase the squelch level (tight [PTT] squelch) or [MONI] to decrease the squelch level (loose [MONI] squelch). Squelch level will be xed after 1 sec.
D Open the squelch Pushing and holding [MONI] cancels the squelch function. You can receive any signals on a channel. Push [MONI] to turn ON the tone squelch function again.

Auto Scan function

Auto scan function proceeds in sequence from lower channel to higher channel numbers. Scanning searches for signals automatically and makes it easier to locate new stations for contact or listening purposes. q Rotate the [CH] select knob to CH 16. w Scan starts automatically.
TX/RX indicator LED blinks green slowly. When receiving a signal, scan pauses until the signal disappears.
CONVENIENT: You can perform the scan start/stop by the optional HM-75A SPEAKER-MICROPHONE [Mic A] key.

Page 19 (1,1)

Setting the group code number
D USING THE CTCSS TONE CODE The transceiver is equipped with 52 CTCSS tones. (See next page) CTCSS operation provides communication with silent standby since you will only receive calls from group members using the same CTCSS tone. You can assign a different tone to CH 1 to CH 15 independently. q While pushing and holding [PTT], [S-Ring/C-Ring], [MONI], turn [VOL] to turn the power ON. w Select the desired CH 1 to CH 15 that you want to assign the CTCSS tone frequency to. e Push and hold [S-Ring/C-Ring] until a beep (Pi) is emitted. r Push [PTT] the necessary number of times to choose the 10 digit of the desired code from the channel list. t Push [S-Ring/C-Ring].
Conrmation beep is emitted. (See next page.)
y Push [PTT] the necessary number of times to choose the 1 digit of the desired code from the frequency list. u Push [S-Ring/C-Ring]. i Turn the power OFF, and then ON again. [Example] To assign tone code No. 28 as CH1; q While pushing and holding [PTT], [S-Ring/C-Ring] and [MONI], turn [VOL] to power ON. w Select the CH 1, then push and hold [S-Ring/C-Ring] until a beep (Pi) is emitted. e Push [PTT] twice to choose the 10 digit of the desired channel. r Push [S-Ring/C-Ring], then push [PTT] eight times to choose the 1 digit of the desired code. t Push [S-Ring/C-Ring]. A long beep and 3 short beeps are emitted. y Turn the power OFF, and then ON again.

Page 20 (1,1)

CTCSS tone code list : EIA/TIA standard code (Recommended to use these.)
No. Freq. OFF 67.0 69.3* 71.0 71.9 74.4 77.0 79.7 82.5 85.4 88.5 91.5 94.8 97.4 100.0 103.5 No. Freq.
107.2 110.9 114.8 118.8 123.0 127.3 131.8 136.5 141.3 146.2 151.4 156.7 159.8 162.2 165.5 167.9

No. 46 47

Freq. 171.3 173.8 177.3 179.9 183.5 186.2 189.9 192.8 196.6 199.5 203.5 206.5 210.7 218.1 225.7 229.1

No. 52

233.6 241.8 250.3 254.1 270.4
*Reserved for Smart-Ring function

(Unit: Hz)

Conrmation beep list
Push [PTT] no 1 (Once) 2 (Twice) 3 (Third) 4 (Fourth) Conrmation beep

G G GG GGG GGGG

Push [PTT] 5 (Fifth) 6 (Sixth) 7 (Seventh) 8 (Eighth) 9 (Ninth)

Conrmation beep

GGGGG G GG GGG GGGG
G; Single beep ; Long beep

Page 21 (1,1)

D CTCSS FIND This transceiver can detect the CTCSS tone frequency in the received signal. By monitoring a signal that is being transmitted from the other station, you can determine the tone frequency required to communicate with them. This function very useful when you are going to communicate with unknown CTCSS code number stations. CTCSS FIND scans all of the CTCSS codes, then stops when a tone code is detected. q While pushing and holding [S-Ring/C-Ring], [MONI], turn [VOL] to turn the power ON. w Select the desired CH 1 to CH 15 that you want to assign the CTCSS tone code. e Push and hold [S-Ring/C-Ring] until a beep (Pi) is emitted. CTCSS FIND starts to scan the code. r CTCSS FIND stops when the tone code is detected. t Push [S-Ring/C-Ring] to determine the tone code number. y Turn the power OFF, and then ON again.
D Turn the squelch function ON/OFF Push and hold [MONI] to turn the tone squelch function OFF. You can receive any signals on a channel, when you receive the other groups signal. Push [MONI] to turn ON the tone squelch function again. You can receive only signals containing the same as your group code.

Page 22 (1,1)

D USING THE DTCS CODE This transceiver is equipped with 83 DTCS codes. DTCS operation provides communication with silent standby since you will only receive calls from group members using the same DTCS number. You can assign different numbers to CH 1 to CH 15 independently. q While pushing and holding [PTT], [S-Ring/C-Ring] and [MONI], turn [VOL] to turn the power ON. w Select the desired CH 1 to CH 15 that you want to assign the DTCS code to. e Push and hold [MONI] until a beep (Pi) is emitted. r Push [PTT] the necessary number of times to choose the 100 digit of the desired code number. t Push [S-Ring/C-Ring].

Conrmation beep is emitted. (See p. 15)
y Push [PTT] the necessary number of times to choose the 10 digit of the desired code number. u Push [S-Ring/C-Ring].
i Push [PTT] the necessary number of times to choose the 1 digit of the desired code number. o Push [S-Ring/C-Ring]. Conrmation beep is emitted. (See p. 15) !0 Push [PTT] once more, if you want to use Inverse mode. !1 Push [S-Ring/C-Ring] to complete the setting. Conrmation beep is emitted. (See p. 15) !2 Turn the power OFF, and then ON again.

Page 23 (1,1)

[Example] To assign code 261I (Inverse) as CH12; q While pushing and holding [PTT], [S-Ring/C-Ring], [MONI], turn [VOL] to turn the power ON. w Select CH 12. e Push and hold [MONI] until a beep (Pi) is emitted. r Push [PTT] twice to choose the 100 digit of the code number. t Push [S-Ring/C-Ring]. Conrmation beep is emitted. (See p. 15) y Push [PTT] six times to choose the 10 digit of the code number. u Push [S-Ring/C-Ring]. Conrmation beep is emitted. (See p. 15) i Push [PTT] once to choose the 1 digit of the code number. o Push [S-Ring/C-Ring]. Conrmation beep is emitted. (See p. 15) !0 Push [PTT] once more, to use Inverse mode. *You can skip step !0, if you want to use Normal mode. !1 Push [S-Ring/C-Ring] to complete the setting. Conrmation beep is emitted. (See p. 15) !2 Turn the power OFF, and then ON again.
DTCS code list (EIA/TIA standard code)

Page 24 (1,1)

RING FUNCTION

Smart-Ring

The ring function has an answer back feature. This allows you to confirm whether or not a call has reached the member of your group even if the operator is temporarily away from the transceiver. D Smart-Ring operation (see right) q Set the same operating channel and CTCSS tone* code for all of your group transceivers. w Push [S-Ring/C-Ring] to send the Smart-Ring call. When a member of your group station answers your call, then the transceiver emits beep tones for every 30 sec. and TX/RX indicator blinks with an orange color. Push [MONI] to cancel the Ringer beep and indication. When no answer comes back, the transceiver emits short failure beep tones. e Push [PTT] to answer the call and to stop the beeps and blinking. *NOTE: This function is available only when the called station has use the same CTCSS tone code and the same operating channels as you.

Call-Ring

Sends the pre-selected ring tone to your group members. D Select the Call-Ring melody q While pushing and holding [PTT] and [S-Ring/C-Ring], rotate [VOL] to turn the power ON. A sample melody is emitted. w Rotate [CH] to select the ringer melody. Push [S-Ring/C-Ring] to monitor the selected melody once more. e Turn the power OFF to determine the melody.

Page 25 (1,1)

RINGER FUNCTION

Smart-Ring operation

push [S-Ring/C-Ring]

Piro P iro

Answer back (automatic)

Piro Piro

Communication
D Call your group member with Call-Ring melody Pushing and holding [S-Ring/C-Ring] to sends a ring tone without pushing [PTT]. The ring tone is emitted while the [S-Ring/C-Ring] key is pressed. The same ring tone comes from your group stations speaker.

Page 26 (1,1)

OTHER FUNCTIONS

Monitor audible function

The monitor function allows you to open the transceivers squelch manually to check whether a channel is busy or not. The transceiver has 2 conditions for receive standby: Audible condition: This condition mutes audio ONLY when no carrier is present. You can receive (or monitor) any signals on a channel. Push and hold the [MONI] switch to cancel the CTCSS or DTCS tone squelch function. Any audio mute functions are cancelled while pushing the [MONI] switch. Inaudible condition: This condition mutes ALL signals except those directed to you. Therefore you should check a channels condition (busy or not) with the monitor function before transmitting. Push the [MONI] switch momentarily to select the inaudible condition.

All signals are received

Only signals containing the proper tone are received

Time-Out Timer

The transceiver has time-out timer function. This function prevents continuous, extend transmissions. This timer automatically turns a transmission OFF 3 min. after it starts. A warning beep emits 10 sec. before the limit is reached. The end beep emits 5 times to announce the end of the transmission.

Page 27 (1,1)

Power save function
The power save function reduces the current drain to conserve battery power. The power save function is automatically turned ON when no operation is performed or no signal is received for 5 sec.

Low battery indication

The TX/RX LED indicates 4 levels of the Low battery condition as follows. If the Low battery warning appears during operation, please charge or replace the battery. [Brink patterns] Low BATT1: You should charge the battery. (blinks slowly)

In an extreme low temperature surrounding (around 20C), the capacity of the battery may exhaust quickly (especially Alkaline batteries). In such case, we recommend to charge the battery or replace the batteries, when the Low Battery Indication appears during operation.

Page 28 (1,1)

5 OTHER FUNCTIONS Optional HM-75A functions
The optional HM-75A allows you to remotely send Smart-Ring/CallRing calls, open the squelch, etc. The switches on the HM-75A function as follows. CAUTION: When connecting the HM-75A to the transceiver, make sure that the transceiver is turned OFF, otherwise the transceiver may malfunction.

Key Push Push and hold

Mic UP Mic DOWN Mic A Mic B
Sends Smart-Ring. Turn the Tone Squelch ON. Start/Stop scan B. ---
Sends Call-Ring. Turn the Tone Squelch OFF. -----

Mic UP

Mic Down

Page 29 (1,1)

SPECIFICATIONS

GENERAL

Frequency coverage Mode No. of operating Ch. Power supply requirement Current drain Operating temp. range No. of CTCSS freq. Dimensions (projections not included) Weight : 446.00625446.09375 MHz : F3E (FM) : 8 (simplex) : 7.2 V (R6x6) or BP-222 : 0.6 A approx. : 25C to +55C : 38 : 54(W)x128(H)x37(D) mm
: 317 g (including BP-222 Ni-Cd batteries) : Less than 500 mW ERP : 3-conductor 2.5 (d) mm/2.2 k : Less than 26.5 dBV/m (20 dB SINAD) : More than 500 mW at 5 % distortion with an 8 load : 2-conductor 3.5 (d) mm/8

TRANSMITTER

Output power Ext. mic. connector

RECEIVER

Sensitivity Audio output power (at 7.2 V DC) Ext. speaker connector
All stated specications are subject to change without notice or obligation. 24

Page 30 (1,1)

OPTIONS

Options

D BATTERY PACKS BP-208 BATTERY CASE Allows a set of Alkaline batteries to operate the handheld when charging the rechargeable battery or in emergencies, etc. 6 AA (R6) cells are required. BP-209 Ni-Cd BATTERY PACK 7.2 V/1100 mAh Ni-Cd battery pack, allows more than 12 hours operation. BP-210 Ni-MH BATTERY PACK 7.2 V/1650 mAh Ni-MH battery pack, allows approx. 18.5 hours operation. BP-222 Ni-Cd BATTERY PACK 7.2 V/600 mAh Ni-Cd battery pack, allows approx. 6.5 hours operation (Same as supplied with models). D CHARGER BC-119N DESKTOP CHARGER + AD-101 For rapid charging of battery packs. An AC adaptor is supplied with the charger. Charging time: 1.5 to 2 hrs. BC-121N MULTI-CHARGER + AD-101 For rapid charging up to 6 battery packs simultaneously. An AC adaptor may be supplied depending on version. Six AD-101s are necessary. Charging time: 1.5 to 2 hrs. BC-144 DESKTOP CHARGER For rapid charging of BP-209 (Ni-Cd), BP-210 (Ni-MH) and BP222 (Ni-Cd). BC-146 DESKTOP CHARGER For regular charging of BP-209 (Ni-Cd), BP-210 (Ni-MH) and BP222 (Ni-Cd).

Page 31 (1,1)

D OTHER OPTIONS HM-46L/HM-75A/HM-131L SPEAKER-MICROPHONES Combination speaker-microphone that provides convenient operation while hanging the transceiver from your belt. HM-75A has programmable function key Mic Up, Mic Down, Mic A, Mic B. HM-131L has a moisture proof construction. HM-128L EARPHONE-MICROPHONE HS-51 HEAD SET Allows you hands-free operation. Includes PTT and TOT. VS-1L VOX/PTT CASE + HS-94/HS-95/HS-97 Separated VOX/PTT unit and one of the following microphone unit is required additionally. HS-94: Ear hook type HS-95: Neck-arm type HS-97: Throat microphone SP-13 EARPHONE Provides clear receive audio in noisy environments. MB-68/MB-74/MB-87 BELT CLIPS MB-68: Regular type belt clip. MB-74: Exclusive alligator-type belt clip. Same as that supplied with the transceiver. MB-87: Swivel belt clip.

Page 32 (1,1)

GLOSSARY
What is squelch? A squelch circuit allows you to mute undesired noise while receiving no signal and emit audio while receiving signals. This provides quiet standby. The [MONI] key cancels the squelch setting. This is useful to listen to weak signals that do not open the squelch.
Talk Range The IC-F22SR is designed to maximize performance and improve transmission range in the field. However, the single most important factor in transmit range (talk power) is your surrounding environment. These radios are line of sight radios and as such, transmission range is inuenced by the degree to which you can see the other communicating party. Large concrete structures and heavy foliage or transmission from inside a building or vehicle will reduce your talk power. Optimal range: wide, open areas free of obstructions. Medium range: large buildings or trees blocking your line of sight. Minimum range: mountainous areas or areas of heavy foliage.

Page 33 (1,1)

What is CTCSS (Continuous Tone Coded Squelch System) ? CTCSS (Continuous Tone Coded Squelch System) allows communication with silent stand by. Only signals containing your group code can open the squelch. This conveniently eliminates unwanted audio and is useful in group activities or security related activities where unwanted output can be a problem. Note that CTCSS group mode is not privateanyone can receive your calls. The IC-F22SR is equipped with max. 52 tone codes for CTCSS use. Selecting a code applies it to all 8 operating channels. Each push of [PTT] superimposes your group code over your transmit signal; and, only signals containing the same code can open your squelch. To temporarily hear all signals (including noise) push and hold [MONI]. Do not use CTCSS if you want to be able to hear signals on all channels.
Auto Scan function + Smart-Ring The Auto Scan function searches for signals automatically and makes it easier to locate new stations for contact or listening purposes. BUT because the Auto Scan function checks each operating channel for only a few moments, the transceiver's response accuracy to Smart-Ring calls is reduced. Use one of CH 115 when you and your group are going to use the Smart-Ring function, otherwise the SmartRing function may fail to answer-back the call.

Page 34 (1,1)

ABOUT CE
CE Versions of the IC-F22SR which display the CE symbol on the serial number seal, comply with the essential requirements of the European Radio and Telecommunication Terminal Directive 1999/5/EC. This warning symbol indicates that this equipment operates in non-harmonised frequency bands and/or may be subject to licensing conditions in the country of use. Be sure to check that you have the correct version of this radio or the correct programming of this radio, to comply with national licensing requirement.
IC-F22SR_2.qxd 03.5.29 14:11 Page 35 (1,1)
DECLARATION OF CONFORMITY

We Icom Inc. Japan

1-1-32, Kamiminami, Hirano-ku Osaka 547-0003, Japan
Dsseldorf 31th July 2001 Place and date of issue
Declare on our sole responsability that this equipment complies with the essential requirements of the Radio and Telecommunications Terminal Equipment Directive, 1999/5/EC, and that any applicable Essential Test Suite measurements have been performed. Kind of equipment: Type-designation: UHF PMR TRANSCEIVER

Icom (Europe) GmbH

iC-f22sr
Himmelgeister strae 100 D-40225 Dsseldorf Authorized representative name
Version (where applicable): This compliances is based on conformity with the following harmonised standards, specifications or documents: i) EN 60950 (August 1992) + A11: 1997 ii) EN (March 2001) iii) EN v1.2.1 (February 1999) iv) v)
T. Maebayashi General Manager

Signature

Page 36 (1,1)
<Intended Country of Use> I GER I FRA I ESP I SWE I AUT I NED I POR I DEN I GBR I BEL I ITA I FIN I IRL I LUX I GRE I SUI I NOR
A-6069D-1EU-w Printed in Japan 20012003 Icom Inc.
1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003 Japan

Icom (UK) Ltd.

Sea Street, Herne Bay, Kent CT6 8LD Telephone: +44 (0) 1227 741741. Fax: +44 (0) 1227 741742. Telex: 317210 BUREAU G URL: www.icomuk.co.uk/ e-mail: info@icomuk.co.uk.

Icom Press Release

27th June 2005
Crystal Radio Systems Ltd Secure Homebase Contract
Icom (UK) Ltd dealer, Crystal Radio Systems Ltd has won a prestigious contract to supply the DIY retailer Homebase with over 2,000 IC-F22SR licence free PMR446 transceivers. The equipment is being used to improve communication between cashiers, staff on the sales floor and staff on the information desk. The radios allow staff to deal with issues such as price checks and stock availability in the store or warehouse. They also provide a fast method of alerting staff to health and safety or security issues. Gary Clarke, Managing Director of Crystal Radio Systems Ltd said,' The radios were introduced to Homebase stores between November 2004 and January 2005. We fitted out 105 stores, in five regions, before Christmas. The remaining stores were equipped after Christmas, the rollout was completed by the end of Jan 2005. Seven IC-F22SR's have been issued to each store. 67 stores that we identified as high risk had an additional IC-F22SR supplied.' Gary added, 'When we initially spoke with Homebase regarding their radio communication requirements, they were already leaning towards PMR446 type radios. We recommended that they should consider a top tier PMR446 radio such as the Icom IC-F22SR, as we have found it offers excellent reliability over the years. We have supplied thousands of IC-F22SR's since they were launched and we have very rarely seen any of these units back. They are very easy to configure / reprogram should the need arise e.g. in the event of co- channel interference, and the F22SR can also be programmed with DCS.' He added, 'We wanted to achieve compatibility throughout the stores in the UK and give them the benefit of using multiple channels. None of the stores require the use of a base station and the lower cost of the PMR446 radios was an obvious attraction.'

Page 1 of 3

Directors: D J Stockley, P A Hadler, R Stockley & A Stockley. Registered in England No. 1461875. VAT Reg. No. 332975637 Q:\Master Press Releases 3\HomebaseCrystalRadioPressRelease.doc

Count on us!

Denis Collen, Retail Projects Manager at Homebase said, We initially tested the principle of using simple and cheap radios with a trial of 16 stores a year ago. Staff feedback told us that we had to search for a more practical and robust solution that would have no maintenance issues. The Icom unit was tested in store over the peak period to ensure that it met these criteria. Staff feedback indicated that it did.' It is not just the front line staff who have been issued with the Icom transceivers. As with most stores in a retail environment the security guard has been included. Denis Collen, said, In many stores the security guard is issued with a radio. This is linked to the staff on the floor to highlight any customers that they may suspect are up to no good. He/she is able to alert staff without alerting the suspect and in many cases they are able to deal with the incident discreetly!' As to the success of the system Denis said,' Customers can see we are taking service seriously when queries are dealt with in no time at all. Security, efficiency, and customer service, which are very important in such a competitive industry, have all been improved since the addition of these two-way radios within the stores. They are great for us and great for customers, popular with staff, very efficient and absolutely fantastic.' On winning this contract, Gary Clarke, Managing Director of Crystal Radio Systems Ltd said, 'We were absolutely delighted. Crystal has many blue chip customers but it is unusual within our industry to gain an order of such magnitude. We have dedicated staff dealing with Homebase and we have found that the close liaison has developed a strong working relationship between both companies.' Bob Stockley, Sales & Marketing Director for Icom (UK) Ltd said, 'We are absolutely delighted that 'Homebase' chose Icom. With so many multi location delivery's required in such a short Page 2 of 3

period of time the logistics of this project where to say the least, very challenging. Gary and the team at Crystal Radio did a fantastic job. Working with them ensured a fast and seamless roll out, delivery and user training program.' -ENDAbout Crystal Radio Systems Ltd (www.twoway-radio.co.uk) Crystal Radio Systems Ltd was formed by Gary Clarke (MD) in 1999. Crystal as gone onto become one of the largest suppliers of two way radios in the United Kingdom. For more information, please contact: Gary Clarke, Managing Director, sales@twoway-radio.co.uk About Homebase (www.homebase.co.uk) Homebase is the second largest DIY brand in the UK offering approximately 40,000 DIY, home and gardening lifestyle products. Founded in 1979, today the Company has nearly 300 stores throughout the UK and The Republic of Ireland with an exciting programme of store openings. Homebase employ over 17,000 staff in the UK serving over 1.5 million customers a week - an average of 78 million a year. For more information, please contact: Media Relations, Media.Relations@homebase.co.uk Corporate background (www.icomuk.co.uk) Icom (UK) Ltd was established in 1974 and is the sole UK and Republic of Ireland importer and distributor for Icom Inc., of Osaka, Japan. Based in Herne Bay, Kent, the company is privately owned with 42 staff. A comprehensive portfolio of radio transceiver, receiver, navigation and computer products is maintained to suit the consumer, commercial, radio-amateur, marine and aviation markets. Equipment is available in fixed-base, vehicle-mobile and handheld formats to suit a wide range of specifications and applications. For more information, please contact: Ian Lockyer, Marketing Manager, ian@icomuk.co.uk Annabel Clarke, Marketing Assistant, annabelc@icomuk.co.uk For images, transparencies and other graphic items please contact: Roger Diamond, Creative Manager, roger@icomuk.co.uk

Page 3 of 3