INSTRUCTION MANUAL

VHF TRANSCEIVER

iF14/S

UHF TRANSCEIVER

iF24/S iF26-L

This device complies with Part 15 of the FCC rules. Operation is subject to the condition that this device does not cause harmful interference.
SAFETY TRAINING INFORMATION
Your Icom radio generates RF electromagnetic energy during transmit mode. This radio is designed for and classified as Occupational Use Only, meaning it must be used only during the course of employment by individuals aware of the hazards, and the ways to minimize W ARN ING such hazards. This radio is NOT intended for use by the General Population in an uncontrolled environment. This radio has been tested and complies with the FCC RF exposure limits for Occupational Use Only. In addition, your Icom radio complies with the following Standards and Guidelines with regard to RF energy and electromagnetic energy levels and evaluation of such levels for exposure to humans: CC OET Bulletin 65 Edition 97-01 Supplement C, Evaluating F Compliance with FCC Guidelines for Human Exposure to Radio Frequency Electromagnetic Fields. merican National Standards Institute (C95.1-1992), IEEE Standard A for Safety Levels with Respect to Human Exposure to Radio Frequency Electromagnetic Fields, 3 kHz to 300 GHz. merican National Standards Institute (C95.3-1992), IEEE RecomA mended Practice for the Measurement of Potentially Hazardous Electromagnetic Fields RF and Microwave. he following accessories are authorized for use with this product. T Use of accessories other than those specified may result in RF exposure levels exceeding the FCC requirements for wireless RF exposure.; Belt Clip (MB-94), Rechargeable Li-Ion Battery Pack (BP230N/BP-232N) and Speaker-microphone (HM-131L). To ensure that your expose to RF electromagnetic energy is within the FCC allowable limits for occupational use, always adhere to the following guidelines:

C AU TIO N

DO NOT operate the radio without a proper antenna attached, as this may damaged the radio and may also cause you to exceed FCC RF exposure limits. A proper antenna is the antenna supplied with this radio by the manufacturer or antenna specifically authorized by the manufacturer for use with this radio. O NOT transmit for more than 50% of total radio use time (50% D duty cycle). Transmitting more than 50% of the time can cause FCC RF exposure compliance requirements to be exceeded. The radio is transmitting when the Transmit indicator lights red. You can cause the radio to transmit by pressing the PTT switch or VOX function. LWAYS keep the antenna at least 2.5 cm (1 inch) away from the A body when transmitting and only use the Icom belt-clip which is listed on page 35 when attaching the radio to your belt, etc., to ensure FCC RF exposure compliance requirements are not exceeded. To provide the recipients of your transmission the best sound quality, hold the antenna at least 5 cm (2 inches) from your mouth, and slightly off to one side. The information listed above provides the user with the information needed to make him or her aware of RF exposure, and what to do to assure that this radio operates with the FCC RF exposure limits of this radio. Electromagnetic Interference/Compatibility During transmissions, your Icom radio generates RF energy that can possibly cause interference with other devices or systems. To avoid such interference, turn off the radio in areas where signs are posted to do so. DO NOT operate the transmitter in areas that are sensitive to electromagnetic radiation such as hospitals, aircraft, and blasting sites. Occupational/Controlled Use The radio transmitter is used in situations in which persons are exposed as consequence of their employment provided those persons are fully aware of the potential for exposure and can exercise control over their exposure.

FOREWORD

READ ALL INSTRUCTIONS carefully and completely before

TABLE OF CONTENTS

SAFETY TRAINING INFORMATION...i. FOREWORD.... iii EXPLICIT DEFINITIONS... iii. OPERATING NOTES.... iii PRECAUTION... iv TABLE OF CONTENTS...v. 1 ACCESSORIES... 15 Supplied accessories...1 Accessory attachments...2 Front, top and side panels..6. 2 PANEL DESCRIPTION... 611 LED indicator...8. Programmable function keys...9 Turning power ON....12. Channel selection...12. 3 CONVENTIONAL OPERATION.. 1217 Call procedure...13 Receiving and transmitting...14 Scrambler function...16 Setting the squelch level..16. Man Down Emergency Call...17 Emergency Call...OPTIONAL UNIT INSTALLATION.. 1819 Optional unit installation...18 Scrambler unit installation...BATTERY CHARGING... 2027 Caution....20 Optional battery chargers...23. 6 BATTERY CASE... 2829 Optional battery case (BP-240)..SWIVEL BELT CLIP... 3033 MB-93 contents...30 To attach....30 To detach...OPTIONS.... 3437. 9 FCC INFORMATION...38

ACCESSORIES

Supplied accessories
The following accessories are supplied: Qty. q Flexible antenna. 1 w Battery pack . 1 e Belt clip. 1 r Unit cover (double-sided tape)*. 1 t Jack cover (with screws). 1 set
*Use the unit cover as a spare. Ask your dealer for details.

Accessory attachments

D Flexible antenna
Connect the supplied flexible antenna to the antenna connector. CAUTION: NEVER HOLD the antenna when carrying the transceiver. ransmitting without an antenna T may damage the transceiver.

D Battery pack

To attach the battery pack: Slide the battery pack on the back of the transceiver in the direction of the arrow (q), then lock it with the battery release button.
lide the battery pack until the battery release button makes a click S sound.
To release the battery pack: Push the battery release button in the direction of the arrow (w) as shown below. The battery pack is then released. NEVER release or attach the battery pack when the transceiver is wet or soiled. This may result in water or dust getting into the transceiver/battery pack and may result in the transceiver being damaged.

D Jack cover

A ttach the jack cover when the optional speaker-microphone is not used. To attach the jack cover: q ttach the jack cover to the A [SP MIC] connector. w Tighten the screws. To detach the jack cover: q nscrew the screws with a U phillips screwdriver. w etach the jack cover for the D optional equipment connection.

q w q w q w

D Belt clip
To attach the belt clip: q elease the battery pack if it is attached. R w lide the belt clip in the direction of the arrow until the belt clip S is locked and makes a click sound.
To detach the belt clip: q elease the battery pack if it is attached. R w inch the clip (q), and slide the belt clip in the direction of the P arrow (w). w q
Front, top and side panels
q IC-F14S/F24S IC-F14/F24/F26-L

PANEL DESCRIPTION

w e Speaker

r Microphone

q CHANNEL SW/SELECTOR IC-F14S/F24S : Toggle the channel switch to select the pre-programmed channel 1 or 2. IC-F14/F24/F26-L : Rotate the channel selector to select the pre-programmed memory channels. w VOLUME CONTROL [VOL] Rotate to turn the power ON/OFF and adjust the audio level.
e LED INDICATOR (p. 8) ights red while transmitting. L ights green while receiving a signal, or when the squelch is L open. ights/blinks orange when the matched 2/5-tone code is reL ceived, according to the pre-programming. r SPEAKER-MICROPHONE CONNECTOR [SP MIC] Connects the optional speaker-microphone, earphone, etc.
[SP MIC] jack cover NOTE: Attach the [SP MIC] jack cover when the optional equipment is not used. (p. 4) t DEALER-PROGRAMMABLE KEY [Lower] The desired function can be assigned by your dealer. (p. 9) y PTT SWITCH [PTT] Push and hold to transmit; release to receive. u DEALER-PROGRAMMABLE KEY [Upper] The desired function can be assigned by your dealer. (p. 9) i ANTENNA CONNECTOR Connects the supplied antenna. D Programmable key reference

Upper Lower

LED indicator
The LED indicator indicates several information as follows; (Ref.; R=Red, G=Green, O=Orange)
TX: Turns Red while transmitting a signal.
RX: Turns Green while receiving a signal.
Call LED (ON): When receiving a matched 2/5-tone.

E D ON

Call LED (Blink): When receiving a matched 2/5-tone.

O G O G G G G R

E D Blink
Fast/Slow scan: Blinks while Fast/Slow scan is activated. Low BATT1: You should charge the battery. (blinks slowly)

B ATT1

Low BATT2: You must charge the battery. (blinks fast)

G R R G R G

B ATT2
TX low BATT2: Low BATT2 was detected during TX mode. CH err: Non-programmed channel is selected.
R O R O R O R O R O R O R O R O

w BATT2

Programmable function keys
The following functions can be assigned to [Upper] and [Lower] programmable function keys. Consult your Icom dealer or system operator for details concerning your transceivers programming. If the programmable function names are bracketed in the following explanations, the specific key used to activate the function depends on programming. SCAN A KEY his keys operation depends on the Power ON Scan setting. T When the power ON scan function is turned OFF; Push to start and cancel scanning operation. In case of transmission during scan, cancels scanning. When the power ON scan function is turned ON; Push to pause scanning. Scanning resumes after passing a specified time period. In case of transmission during scan, pauses scanning. Scanning resumes after passing a specified time period. SCAN B KEY Push to start and cancel scanning operation. In case of transmission during scan, pauses scanning. Scanning resumes after passing a specified time period. PRIORITY CHANNEL KEYS ush to select the Priority A or Priority B channel. P ush and hold [Prio A (Rewrite)] to rewrite the Prio A channel. P MR-CH 1/2/3/4 KEYS Push to select a memory channels 1 to 4 directly. NOTE: The memory channels 3 and 4 are available for IC-F14S/ F24S when [MR-CH 3] and [MR-CH 4] keys are assigned.

MONITOR KEY M ute and release the CTCSS (DTCS) or 2-tone squelch mute. Open any squelch/deactivate any mute while pushing this key. (LMR operation only) ctivates one of (or two of) the following functions on each A channel independently: (PMR operation only)
ush and hold to un-mute the channel (audio is emitted; Audible P condition). Push to mute the channel (sets to Inaudible only). Push to un-mute the channel (sets to Audible only). ush after the communication is finished to send a reset code. P
NOTE: The un-mute condition (Audible condition) may automatically return to the mute condition (Inaudible condition) after a specified period.
LOCK KEY Push and hold to electronically lock all programmable keys except the following: [Call] (incl. Call A and Call B), [Moni(Audi)] and [Emergency] keys. OUTPUT POWER SELECTION KEY Select the transmit output power temporarily or permanently, depending on the pre-setting.
Ask your dealer for the output power level for each selection.
TALK AROUND KEY Push to turn the talk around function OFF. Push and hold to turn the talk around function ON.
he talk around function equalizes the transmit frequency to the T receive frequency for transceiver-to-transceiver communication.
WIDE/NARROW KEY Push to select the IF bandwidth to wide.
he wide passband width can be selected from 25.0 or 20.0 kHz T using the CS-F14 cloning software. (PMR operation only) Ask your dealer for details.
Push and hold to select the IF bandwidth to narrow.
DTMF AUTODIAL KEY Push to transmit the programmed DTMF code. CALL KEYS Push to transmit a 2/5-tone code.
all transmission is necessary before you call another station deC pending on your signalling system. Call A] and/or [Call B] keys may be available when your system [ employs selective Individual/Group calls. Ask your dealer which call is assigned to each key.
EMERGENCY KEYS Push and hold to transmit an emergency call. W hen [Emergency Single (Silent)] or [Emergency Repeat (Silent)] is pushed, an emergency call is transmitted with no beep emission.
f you want to cancel the emergency call, push (or push and hold) I the key again before transmitting the call. he emergency call is transmitted one time only or repeatedly T until receiving a control code depending on the pre-setting.
VOICE SCRAMBLER FUNCTION KEYS Push to turn the voice scrambler function OFF. Push and hold to turn the voice scrambler function ON. OPT OUT KEYS Push to inactivate the connected output signal level. Push and hold to activate the connected output signal level. SIREN KEY Push to emit a siren. This function can be used for situations other than an emergency alert such as a security alarm for example.

Turning power ON

Rotate [VOL] to turn power ON.

CONVENTIONAL OPERATION

Channel selection

IC-F14S/F24S: Toggle [CHANNEL SWITCH] to select the channel 1 or 2, or, push one of [MR-CH 1] to [MR-CH 4] key to select a channel directly.
he memory channels 3 and 4 are availT able when [MR-CH 3] and [MR-CH 4] keys are assigned.
[CHANNEL SWITCH] [CHANNEL SELECTOR]
IC-F14/F24/F26-L: Rotate [CHANNEL SELECTOR] to select the desired operating channel, in sequence; or, push one of [MR-CH 1] to [MR-CH 4] key to select a channel directly.
AUTOMATIC SCAN TYPE: Channel setting is not necessary for this type. When turning the power ON, the transceiver automatically starts scanning. Scanning stops when receiving a call.

Call procedure

When your system employs tone signalling (excluding CTCSS and DTCS), the call procedure may be necessary prior to voice transmission. The tone signalling employed may be a selective calling system which allows you to call specific station(s) only and prevent unwanted stations from contacting you. q elect the desired TX code channel or 2/5-tone code according S to your System Operators instructions.
This may not be necessary depending on programming.
w ush the call key (assigned to one of the dealer programmable P keys.) (p. 11) e fter transmitting a 2/5-tone code, the remainder of your comA munication can be carried out in the normal fashion.
Selective calling Non-selective calling
Receiving and transmitting
NOTE: Transmitting without an antenna may damage the transceiver. See p. 2 for antenna attachment.

Receiving:

q Rotate [VOL] to turn power ON. w oggle [CHANNEL SWITCH] (IC-F14S/F24S), rotate [CHANT NEL SELECTOR] (IC-F14/F24/F26-L) or push one of [MR-CH 1] to [MR-CH 4] key to select a channel. For IC-F14S/F24S:
The memory channels 3 and 4 are available when [MR-CH 3] and [MR-CH 4] keys are assigned.
e hen receiving a call, adjust the audio output level to a comW fortable listening level.

Transmitting:

Wait for the channel to become clear to avoid interference. q hile pushing and holding [PTT], speak into the microphone at W a normal voice level.
hen a tone signalling system is used, the call procedure deW scribed on p. 13 may be necessary.

w Release [PTT] to return to receive. IMPORTANT!: To maximize the readability of your signal; 1. Pause briefly after pushing [PTT]. 2. old the microphone 5 to 10 cm (2 to 4 inches) from your H mouth, then speak into the microphone at a normal voice level.

D Transmitting notes

Transmit inhibit function The transceiver has several inhibit functions which restrict transmission under the following conditions: - he channel is in mute condition. T - Channel is busy. - Un-matched (or matched) CTCSS is received. - The selected channel is a receive only channel. Time-out timer After continuous transmission for the pre-programmed time period, the time-out timer activates, and causes the transceiver to stop transmitting. Penalty timer Once the time-out timer activates, transmission is further inhibited for a period determined by the penalty timer. PTTID call The transceiver sends the ID code (5-tone, DTMF or digital ANI) automatically when [PTT] is pushed (beginning of transmission) and released (end of transmission) depends on the setting.

D DTMF transmission

If the transceiver has [DTMF Autodial] assigned to it, the automatic DTMF transmission function is available. ush [DTMF Autodial] to transmit the DTMF code. P

Scrambler function

The optional voice scrambler units UT-109 (#01) and UT-110 (#01) provide high performance private communication between stations with the same scrambler codes. ush and hold [Scrambler] to turn the scrambler function ON. P ush [Scrambler] to turn the scrambler function OFF. P
Setting the squelch level
The squelch circuit mutes the received audio signal depending on the signal strength. q hile pushing [PTT] and [Lower], W rotate [VOL] to turn the power ON to enter the squelch level adjustment mode. [Upper] w ush [Upper] to increase the P squelch level (tight squelch) or [PTT] [Lower] to decrease the squelch level (loose squelch). [Lower] e otate [VOL] to turn the power R OFF to fix the squelch level.

Man Down Emergency Call

The man down emergency call function transmits an emergency call automatically, after the transceiver laying down in a horizontal position for a pre-set time period. (The optional UT-113 man down unit is required.) After the emergency call, the transceiver performs transmission and reception alternately with the following conditions: - Transmits the microphone signals. - Receives the signal and emits audio. When the emergency cancel code is received, the function is cancelled. IMPORTANT!: Set an emergency channel individually, to provide certain emergency call operation is recommended.

R DANGER! NEVER solder the battery terminals or NEVER modify the battery pack. This may cause heat generation, and the battery may rupture, emit smoke or catch fire. R DANGER! Use the battery only with the transceiver for which it is specified. Never use a battery with any other equipment, or for any purpose that is not specified in this instruction manual. R DANGER! If fluid from inside the battery gets in your eyes, blindness can result. Rinse your eyes with clean water, without rubbing them, and see a doctor immediately. WARNING! Immediately stop using the battery if it emits an abnormal odor, heats up, or is discolored or deformed. If any of these conditions occur, contact your Icom dealer or distributor. WARNING! Immediately wash, using clean water, any part of the body that comes into contact with fluid from inside the battery. WARNING! NEVER put the battery in a microwave oven, highpressure container, or in an induction heating cooker. This could cause a fire, overheating, or cause the battery to rupture. CAUTION! Always use the battery within the specified temperature range for the transceiver (30C to +60C; 22F to +140F) and the battery itself (20C to +60C; 4F to +140F). Using the battery out of its specified temperature range will reduce the batterys performance and battery life. CAUTION! Shorter battery life could occur if the battery is left fully charged, completely discharged, or in an excessive temperature environment (above +50C; +122F) for an extended period of time. If the battery must be left unused for a long time, it must be detached from the radio after discharging. You may use the battery until the remaining capacity is about half, then keep it safely in a cool dry place with the temperature between 20C to +20C (4F to +68F).

D Charging caution

R DANGER! NEVER charge the battery pack in areas with extremely high temperatures, such as near fires or stoves, inside a sun heated car, or in direct sunlight. In such environments, the safety/protection circuit in the battery will activate, causing the battery to stop charging. WARNING! DO NOT charge or leave the battery in the battery charger beyond the specified time for charging. If the battery is not completely charged by the specified time, stop charging and remove the battery from the battery charger. Continuing to charge the battery beyond the specified time limit may cause a fire, overheating, or the battery may rupture. WARNING! NEVER insert the transceiver (battery attached to the transceiver) into the charger if it is wet or soiled. This could corrode the battery charger terminals or damage the charger. The charger is not waterproof. CAUTION! DO NOT charge the battery outside of the specified temperature range: BC-160 and BC-171 (0C to +40C; +32F to +104F). Icom recommends charging the battery at +20C (+68F). The battery may heat up or rupture if charged out of the specified temperature range. Additionally, battery performance or battery life may be reduced.

Optional battery chargers
D Rapid charging with the BC-160
The optional BC-160 provides rapid charging of the Li-Ion battery pack. Charging period: Approx. 3 hours (with BP-232N) The following items are additionally required: n AC adapter (may be supplied depending on version) or the A DC power cable (OPC-515L/CP-17L) is additionally required.
Battery pack AC adapter (Not supplied with some versions.) Transceiver

Turn power OFF

Optional OPC-515L (for 13.8 V power source) or CP-17L (for 12 V cigarette lighter socket) can be used instead of the AC adapter.
IMPORTANT! Ensure the guide lobs on the battery pack are correctly aligned with the guide rails inside the charger adapter.

Guide rail

D Regular charging with the BC-171
The optional BC-171 provides regular charging of the Li-Ion battery pack. Charging period: Approx. 10 hours (with BP-232N) The following items are additionally required: n AC adapter (may be supplied depending on version) or the A DC power cable (OPC-515L/CP-17L) is additionally required.

D AD-106 installation

The AD-106 charger adapter must be installed into the BC-119N or BC-121N before battery charging. C onnect the AD-106 charger adapter and the BC-119N/BC121N as below, then install the AD-106 into the holder space of the BC-119N or BC-121N with the supplied screws.
Desktop charger adapter Connectors
Screws supplied with the charger adapter
D Rapid charging with the BC-119N+AD-106
The optional BC-119N provides rapid charging of the Li-Ion battery pack. Charging period: Approx. 3 hours (with BP-232N) The following items are additionally required: An AD-106 (purchase separately). n AC adapter (may be supplied with BC-119N depending on A version) or the DC power cable (OPC-515L/CP-17L).
Transceiver Battery pack AC adapter (Not supplied with some versions.)
AD-106 charger adapter is installed in BC-119N.
IMPORTANT! Ensure the guide lobs on the battery pack are correctly aligned with the guide rails inside the charger adapter. Guide rails
D Rapid charging with the BC-121N+AD-106
The optional BC-121N allows up to 6 battery packs to be charged simultaneously. Charging period: Approx. 3 hours (with BP-232N) The following items are additionally required. Six AD-106. n AC adapter (BC-157) or the DC power cable (OPC-656) A
Transceiver Battery pack AD-106 charger adapters are installed in each slot. AC adapter (Purchase separately)
DC power cable (OPC-656) (Connect with the DC power supply; 13.8 V/at least 7 A)

Guide rails

Optional battery case (BP-240)
When using the optional battery case, install 6 AAA (LR03) size alkaline batteries as illustrated at right. q nhook the battery cover release hook (q), and open the cover U in the direction of the arrow (w). (Fig.1) w hen, install 6 AAA (LR03) size alkaline batteries. (Fig.2) T
nstall the alkaline batteries only. I e sure to observe the correct polarity. B o not pin the ribbon under the batteries. D

BATTERY CASE

e it the cover in the direction of the arrow (e), then close (r). F Hook the battery cover release hook until it makes a click sound (t). (Fig.3) CAUTION: hen installing batteries, make sure they are all the same W brand, type and capacity. Also, do not mix new and old batteries together. eep battery contacts clean. Its a good idea to clean battery K terminals once a week. ever incinerate used battery cells since internal battery gas N may cause them to rupture. ever expose a detached battery case to water. If the battery N case gets wet, be sure to wipe it dry before using it. NOTE: When the optional battery case is attached, the battery type must be selected to Alkaline battery operation when turning the transceiver ON. Ask your dealer for details.

BP-240

q Fig.2

Fig.3 r t

MB-93 contents
Qty. q Belt clip... 1 w Base clip... 1

SWIVEL BELT CLIP

To attach
q elease the battery pack if it is attached. (p. 3) R w lide the base clip in the direction of the arrow until the base S clip is locked and makes a click sound.
e lip the belt clip to a part of your belt. And insert the transceiver C into the belt clip until the base clip inserted fully into the groove.
r nce the transceiver is locked in place, it swivels as illustrated O below.

To detach

q urn the transceiver upside down in the direction of the arrow T and pull out from the belt clip.
w elease the battery pack if it is attached. (p. 3) R e inch the clip (q), and slide the base clip in the direction of the P arrow (w).

CAUTION:

HOLD THE TRANSCEIVER TIGHTLY, WHEN HANGING OR DETACHING THE TRANSCEIVER FROM THE BELT CLIP. Otherwise the transceiver may not be attached to the holder or swivel properly if the transceiver is accidentally dropped and the base clip is scratched or damaged.

D BATTERY PACK

Battery pack BP-230N BP-232N BP-240 Voltage 7.4 V 7.4 V Capacity 950 mAh (min.) 980 mAh (typ.) 1900 mAh (min.) 2000 mAh (typ.) Battery life*hrs. 18 hrs. *2

OPTIONS

Battery case for AAA (LR03) 6 alkaline
*1 When the power save function is turned ON, and the operating periods are calculated under the following conditions; TX : RX : standby = 5 : 5 : 90 *2 Operating period depends on the alkaline cells used.

C-119N desktop charger + AD-106 charger adapter B + BC-145 ac adapter For rapid charging of battery packs. An AC adapter is supplied with the charger depending on versions. Charging time: approx. 3 hours when BP-232N is attached. C-121N multi-charger + AD-106 charger adapter (6 pcs.) B + BC-157 ac adapter For rapid charging of up to 6 battery packs (six AD-106s are required) simultaneously. An AC adapter should be purchased separately. Charging time: approx. 3 hours when BP-232N is attached. C-160 desktop charger + BC-145 ac adapter B For rapid charging of battery packs. An AC adapter is supplied with the charger depending on versions. Charging time: approx. 3 hours when BP-232N is attached. C-171 desktop charger + BC-147 ac adapter B For regular charging of battery packs. We recommend that the BP-230N charging. An AC adapter is supplied with the charger depending on versions. Charging time: pprox. 10 hours when BP-232N is attached. A Approx. 4 hours when BP-230N is attached.

D CHARGERS

D OPTIONAL UNITS
UT-108 dtmf decoder unit Provides pager and code squelch capabilities. UT-109 (#01)/UT-110 (#01) scrambler units Non-rolling type (UT-109)/Rolling type (UT-110) voice scrambler unit provides higher communication security. UT-124 man down unit Provides a measure of safety when working in a hazardous environment, etc.

D BELT CLIPS

MB-93 swivel belt clip MB-94 belt clip Exclusive alligator-type belt clip. The same as supplied with the transceiver. MB-96N/96F leather belt hanger CP-17L cigarette lighter cable Allows charging of the battery pack through a 12 V cigarette lighter socket. (For BC-119N) OPC-515L/OPC-656 dc power cables Allows charging of the battery pack using a 13.8 V power source instead of the AC adapter. OPC-515L: For BC-119N OPC-656 : For BC-121N

D DC CABLES

D OTHER OPTIONS
SP-13 earphone Provides clear receive audio in noisy environment. HM-153L earphone-microphone HM-131L/158L/159L speaker-microphone Combination speaker-microphone that provides convenient operation while hanging the transceiver from your belt.
HS-94/HS-95/HS-97 headset + VS-1L vox/ptt case HS-94: Ear hook type HS-95: Neck-arm type HS-97: Throat microphone VS-1L: VOX/PTT switch box for hands-free operation, etc. FA-SC73US/FA-SC56VS/FA-SC57VS stubby antennas FA-SC73US: 450490 MHz FA-SC56VS: 150162 MHz FA-SC57VS: 160174 MHz A-SC01U/FA-SC25U/FA-SC57U/FA-SC72U/FA-SC25V/ F FA-SC55V antennas FA-SC01U: 350400 MHz FA-SC25U: 400430 MHz FA-SC57U: 430470 MHz FA-SC72U: 470520 MHz FA-SC25V: 136155 MHz FA-SC55V: 146174 MHz A-SC61VC/FA-SC61UC cut antennas F FA-SC61VC: 136174 MHz FA-SC61UC: 380520 MHz

Icom optional equipment is designed for optimal performance when used with this transceiver. We are not responsible for the transceiver being damaged or any accident caused when using non-Icom optional equipment. Some options may not be available in some countries. Please ask your dealer for details.
D About VS-1L vox/ptt case
The VS-1L is a VOX/PTT unit for Icom handheld transceivers, and allows you hands-free operation. An optional headset (HS-94, etc.) is additionally required for operation.
he VOX (voice operated transmission) function starts transmission T without pushing PTT switch when you speak into the microphone; then, automatically returns to receive when you stop speaking.
Features Straight type head SP/MIC plug equipped Water resistant construction Durable construction Equipped with a PTT switch and revolving clip. MIC/VOX gain adjustment 1 emove the water protection cover on the right side of the VS-1L. R 2 djust the MIC/VOX gain with a thin screw driver. Clockwise roA tation increases the MIC/VOX gain. 3 eturn the protective cover back to the MIC/VOX gain adjustR ment hole.

VS-1L PTT switch

Adjusting pot
Water protection cover VOX PTT

FCC INFORMATION

FOR CLASS B UNINTENTIONAL RADIATORS: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. ncrease the separation between the equipment and receiver. I onnect the equipment into an outlet on a circuit different C from that to which the receiver is connected. onsult the dealer or an experienced radio/TV technician for C help.

A-6369D-1EX-i Printed in Japan 20042009 Icom Inc.
Printed on recycled paper with soy ink.
1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan

IC-F14_F24-6.qxd

06.9.29 6:09 PM

Page A (1,1)

INSTRUCTION MANUAL

VHF TRANSCEIVER

iF14/S

UHF TRANSCEIVER

iF24/S iF26-L
This device complies with Part 15 of the FCC rules. Operation is subject to the condition that this device does not cause harmful interference.

Page i (1,1)

SAFETY TRAINING INFORMATION
Your Icom radio generates RF electromagnetic energy during transmit mode. This radio is designed for and classified as Occupational Use Only, meaning it must be used only during the course of employment by individuals aware of the hazards, and the ways to minimize such hazW ARN ING ards. This radio is NOT intended for use by the General Population in an uncontrolled environment. This radio has been tested and complies with the FCC RF exposure limits for Occupational Use Only. In addition, your Icom radio complies with the following Standards and Guidelines with regard to RF energy and electromagnetic energy levels and evaluation of such levels for exposure to humans: FCC OET Bulletin 65 Edition 97-01 Supplement C, Evaluating Compliance with FCC Guidelines for Human Exposure to Radio Frequency Electromagnetic Fields. American National Standards Institute (C95.1-1992), IEEE Standard for Safety Levels with Respect to Human Exposure to Radio Frequency Electromagnetic Fields, 3 kHz to 300 GHz. American National Standards Institute (C95.3-1992), IEEE Recommended Practice for the Measurement of Potentially Hazardous Electromagnetic Fields RF and Microwave. The following accessories are authorized for use with this product. Use of accessories other than those specied may result in RF exposure levels exceeding the FCC requirements for wireless RF exposure.; Belt Clip (MB-94), Rechargeable Li-Ion Battery Pack (BP-230N/BP-232N) and Speaker-microphone (HM-131L). To ensure that your expose to RF electromagnetic energy is within the FCC allowable limits for occupational use, always adhere to the following guidelines:

C AU TIO N

Page ii (1,1)
DO NOT operate the radio without a proper antenna attached, as this may damaged the radio and may also cause you to exceed FCC RF exposure limits. A proper antenna is the antenna supplied with this radio by the manufacturer or antenna specically authorized by the manufacturer for use with this radio. DO NOT transmit for more than 50% of total radio use time (50% duty cycle). Transmitting more than 50% of the time can cause FCC RF exposure compliance requirements to be exceeded. The radio is transmitting when the Transmit indicator lights red. You can cause the radio to transmit by pressing the PTT switch or VOX function. ALWAYS keep the antenna at least 2.5 cm (1 inch) away from the body when transmitting and only use the Icom belt-clip which is listed on page 31 when attaching the radio to your belt, etc., to ensure FCC RF exposure compliance requirements are not exceeded. To provide the recipients of your transmission the best sound quality, hold the antenna at least 5 cm (2 inches) from your mouth, and slightly off to one side. The information listed above provides the user with the information needed to make him or her aware of RF exposure, and what to do to assure that this radio operates with the FCC RF exposure limits of this radio. Electromagnetic Interference/Compatibility During transmissions, your Icom radio generates RF energy that can possibly cause interference with other devices or systems. To avoid such interference, turn off the radio in areas where signs are posted to do so. DO NOT operate the transmitter in areas that are sensitive to electromagnetic radiation such as hospitals, aircraft, and blasting sites. Occupational/Controlled Use The radio transmitter is used in situations in which persons are exposed as consequence of their employment provided those persons are fully aware of the potential for exposure and can exercise control over their exposure.

Page iii (1,1)

FOREWORD
READ ALL INSTRUCTIONS carefully and completely before

using the transceiver.

SAVE THIS INSTRUCTION MANUAL This instruction
manual contains important operating instructions for the IC-F14/ IC-F14S VHF TRANSCEIVERS and IC-F24/IC-F24S/IC-F26-L UHF TRANSCEIVERS.

EXPLICIT DEFINITIONS

WORD RWARNING CAUTION NOTE DEFINITION Personal injury, fire hazard or electric shock may occur. Equipment damage may occur. If disregarded, inconvenience only. No risk of personal injury, fire or electric shock.

OPERATING NOTES

When transmitting with a portable radio, hold the radio in a vertical position with its microphone 5 to 10 centimeters (2 to 4 inches) away from your mouth. Keep the antenna at least 2.5 centimeters (1 inch) from your head and body. If you wear a portable two-way radio on your body, ensure that the antenna is at least 2.5 centimeters (1 inch) from your body when transmitting.

Page iv (1,1)

PRECAUTION
R WARNING! NEVER hold the transceiver so that the antenna
is very close to, or touching exposed parts of the body, especially the face or eyes, while transmitting. The transceiver will perform best if the microphone is 5 to 10 cm (2 to 4 inches) away from the lips and the transceiver is vertical.
R WARNING! NEVER operate the transceiver with a headset
or other audio accessories at high volume levels.
CAUTION! NEVER short the terminals of the battery pack. NEVER connect the transceiver to a power source other than the
BP-230N or BP-232N. Such a connection will ruin the trans-ceiver.
DO NOT push the PTT when not actually desiring to transmit. AVOID using or placing the transceiver in direct sunlight or in
areas with temperatures below 22F (30C) or above +140F (+60C).
DO NOT modify the transceiver for any reason. MAKE SURE the exible antenna and battery pack are securely
attached to the transceiver, and that the antenna and battery pack are dry before attachment. Exposing the inside of the transceiver to water will result in serious damage to the transceiver. The use of non-Icom battery packs/chargers may impair transceiver performance and invalidate the warranty. FCC caution: Changes or modications to this device, not expressly approved by Icom Inc., could void your authority to operate this transceiver under FCC regulations.
Icom, Icom Inc. and the logo are registered trademarks of Icom Incorporated (Japan) in the United States, the United Kingdom, Germany, France, Spain, Russia and/or other countries.

Page v (1,1)

TABLE OF CONTENTS
SAFETY TRAINING INFORMATION i FOREWORD iii EXPLICIT DEFINITIONS iii OPERATING NOTES iii PRECAUTION iv TABLE OF CONTENTS v 1 ACCESSORIES 15 Supplied accessories 1 Accessory attachments PANEL DESCRIPTION 611 Front, top and side panels 6 LED indicator 8 Programmable function keys CONVENTIONAL OPERATION 1218 Turning power ON 12 Channel selection 12 Call procedure 13 Receiving and transmitting 14 Scrambler function 16 Setting the squelch level 16 Man Down Emergency Call OPTIONAL UNIT INSTALLATION 1819 Optional unit installation 18 Scrambler unit installation BATTERY CHARGING 2025 Battery charging 20 Caution 21 Optional battery chargers SWIVEL BELT CLIP 2629 MB-93 contents 26 To attach 26 To detach OPTIONS 3033

Page 1 (1,1)

ACCESSORIES

I Supplied accessories

The following accessories are supplied: Qty. q Flexible antenna.1 w Battery pack.1 e Belt clip.1 r Unit cover (double-sided tape)*.1 t Jack cover (with screws).1 set
*Use the unit cover as a spare. Ask your dealer for details.

Page 2 (1,1)

I Accessory attachments

D Flexible antenna

Connect the supplied flexible antenna to the antenna connector. CAUTION: NEVER HOLD by the antenna when carrying the transceiver. Transmitting without an antenna may damage the transceiver.

Page 3 (1,1)

Battery pack
To attach the battery pack: Slide the battery pack on the back of the transceiver in the direction of the arrow (q), then lock it with the battery release button.
Slide the battery pack until the battery release button makes a click sound.
To release the battery pack: Push the battery release button in the direction of the arrow (w) as shown below. The battery pack is then released. NEVER release or attach the battery pack when the transceiver is wet or soiled. This may result in water or dust getting into the transceiver/battery pack and may result in the transceiver being damaged.

Page 4 (1,1)

Jack cover
Attach the jack cover when the optional speaker-microphone is not used. To attach the jack cover: To detach the jack cover: q Attach the jack cover to the q Unscrew the screws with a [SP MIC] connector. phillips screwdriver. w Tighten the screws. w Detach the jack cover for the speaker-microphone connection.

Page 5 (1,1)

D Belt clip
To attach the belt clip: q Release the battery pack if it is attached. w Slide the belt clip in the direction of the arrow until the belt clip is locked and makes a click sound.
To detach the belt clip: q Release the battery pack if it is attached. w Pinch the clip (q), and slide the belt clip in the direction of the arrow (w). w q

Page 6 (1,1)

PANEL DESCRIPTION

q IC-F14S/F24S

I Front, top and side panels

IC-F14/F24/F26-L

w e Speaker

r Microphone

q CHANNEL SW/SELECTOR IC-F14S/F24S : Toggle the channel switch to select the pre-programmed channel 1 or 2. IC-F14/F24/F26-L : Rotate the channel selector to select the pre-programmed memory channels. w VOLUME CONTROL [VOL] Rotate to turn the power ON/OFF and adjust the audio level.

Page 7 (1,1)

e LED INDICATOR (p. 8) Lights red while transmitting. Lights green while receiving a signal, or when the squelch is open. Lights/blinks orange when the matched 2/5-tone code is received, according to the pre-programming. r SPEAKER-MICROPHONE CONNECTOR [SP MIC] Connects the optional speaker-microphone. (p. 31)
[SP MIC] jack cover NOTE: Attach the [SP MIC] jack cover when the optional speaker-microphone is not used. (p. 4) t DEALER-PROGRAMMABLE KEY [Lower] The desired function can be assigned by your dealer. (p. 9) y PTT SWITCH [PTT] Push and hold to transmit; release to receive. u DEALER-PROGRAMMABLE KEY [Upper] The desired function can be assigned by your dealer. (p. 9) i ANTENNA CONNECTOR Connects the supplied antenna. D Programmable key reference

Upper Lower

Page 8 (1,1)

LED indicator

The LED indicator indicates several information as follows; (Ref.; R=Red, G=Green, O=Orange)
TX: Turns Red while transmitting a signal.
RX: Turns Green while receiving a signal.
Call LED (ON): When receiving a matched 2/5-tone.
Call LED (Blink): When receiving a matched 2/5-tone.
Fast/Slow scan: Blinks while Fast/Slow scan is activated.
Low BATT1: You should charge the battery. (blinks slowly)
Low BATT2: You must charge the battery. (blinks fast)

G G G G

TX low BATT2: Low BATT2 was detected during TX mode.

R R R R

CH err: Non-programmed channel is selected.
R O R O R O R O R O R O R O R O

Page 9 (1,1)

Programmable function keys
The following functions can be assigned to [Upper] and [Lower] programmable function keys. Consult your Icom dealer or system operator for details concerning your transceivers programming. If the programmable function names are bracketed in the following explanations, the specic key used to activate the function depends on programming. SCAN A KEY This keys operation depends on the Power ON Scan setting. When the power ON scan function is turned OFF; Push to start and cancel scanning operation. In case of transmission during scan, cancels scanning. When the power ON scan function is turned ON; Push to pause scanning. Scanning resumes after passing a specified time period. In case of transmission during scan, pauses scanning. Scanning resumes after passing a specied time period. SCAN B KEY Push to start and cancel scanning operation. In case of transmission during scan, pauses scanning. Scanning resumes after passing a specied time period. PRIORITY CHANNEL KEYS Push to select the Priority A or Priority B channel. Push and hold [Prio A (Rewrite)] to rewrite the Prio A channel. MR-CH 1/2/3/4 KEYS Push to select a memory channels 1 to 4 directly. NOTE: The memory channels 3 and 4 are available for ICF14S/F24S when [MR-CH 3] and [MR-CH 4] keys are assigned.

Page 10 (1,1)

MONITOR KEY Mute and release the CTCSS (DTCS) or 2-tone squelch mute. Open any squelch/deactivate any mute while pushing this key. (LMR operation only) Activates one of (or two of) the following functions on each channel independently: (PMR operation only)
Push and hold to un-mute the channel (audio is emitted; Audible condition). Push to mute the channel (sets to Inaudible only). Push to un-mute the channel (sets to Audible only). Push after the communication is nished to send a reset code.
NOTE: The un-mute condition (Audible condition) may automatically return to the mute condition (Inaudible condition) after a specied period. LOCK KEY Push and hold to electronically lock all programmable keys except the following: [Call] (incl. Call A and Call B), [Moni(Audi)] and [Emergency] keys. OUTPUT POWER SELECTION KEY Select the transmit output power temporarily or permanently, depending on the pre-setting.
Ask your dealer for the output power level for each selection.
TALK AROUND KEY Push to turn the talk around function OFF. Push and hold to turn the talk around function ON.
The talk around function equalizes the transmit frequency to the receive frequency for transceiver-to-transceiver communication.
WIDE/NARROW KEY Push to select the IF bandwidth to wide.
The wide passband width can be selected from 25.0 or 20.0 kHz using the CS-F14 CLONING SOFTWARE. (PMR operation only) Ask your dealer for details.
Push and hold to select the IF bandwidth to narrow.

Page 11 (1,1)

DTMF AUTODIAL KEY Push to transmit the programmed DTMF code. CALL KEYS Push to transmit a 2/5-tone code.
Call transmission is necessary before you call another station depending on your signalling system. [Call A] and/or [Call B] keys may be available when your system employs selective Individual/Group calls. Ask your dealer which call is assigned to each key.
EMERGENCY KEYS Push and hold to transmit an emergency call. When [Emergency Single (Silent)] or [Emergency Repeat (Silent)] is pushed, an emergency call is transmitted without a beep emission.
If you want to cancel the emergency call, push (or push and hold) the key again before transmitting the call. The emergency call is transmitted one time only or repeatedly until receiving a control code depending on the pre-setting.
VOICE SCRAMBLER FUNCTION KEYS Push to turn the voice scrambler function OFF. Push and hold to turn the voice scrambler function ON. OPT OUT KEYS Push to inactivate the connected output signal level. Push and hold to activate the connected output signal level. SIREN KEY Push to emit a siren. This function can be used for situations other than an emergency alert such as a security alarm for example.

Page 12 (1,1)

CONVENTIONAL OPERATION

I Turning power ON

Rotate [VOL] to turn power ON.

I Channel selection

IC-F14S/F24S: Toggle [CHANNEL SWITCH] to select the channel 1 or 2, or, push one of [MRCH 1] to [MR-CH 4] key to select a channel directly.
The memory channels 3 and 4 are available when [MR-CH 3] and [MR-CH 4] keys are assigned. [CHANNEL SWITCH]
IC-F14/F24/F26-L: Rotate [CHANNEL SELECTOR] to select the desired operating channel, in sequence; or, push one of [MR-CH 1] to [MR-CH 4] key to select a channel directly.

[CHANNEL SELECTOR]

AUTOMATIC SCAN TYPE: Channel setting is not necessary for this type. When turning the power ON, the transceiver automatically starts scanning. Scanning stops when receiving a call.

Page 13 (1,1)

I Call procedure
When your system employs tone signalling (excluding CTCSS and DTCS), the call procedure may be necessary prior to voice transmission. The tone signalling employed may be a selective calling system which allows you to call specic station(s) only and prevent unwanted stations from contacting you. q Select the desired TX code channel or 2/5-tone code according to your System Operators instructions.
This may not be necessary depending on programming.
w Push the call key (assigned to one of the dealer programmable keys.) (p. 11) e After transmitting a 2/5-tone code, the remainder of your communication can be carried out in the normal fashion.
Selective calling Non-selective calling

Page 14 (1,1)

I Receiving and transmitting
NOTE: Transmitting without an antenna may damage the transceiver. See p. 2 for antenna attachment.

Receiving:

q Rotate [VOL] to turn power ON. w Toggle [CHANNEL SWITCH] (IC-F14S/F24S), rotate [CHANNEL SELECTOR] (IC-F14/F24/F26-L) or push one of [MR-CH 1] to [MR-CH 4] key to select a channel. For IC-F14S/F24S:
The memory channels 3 and 4 are available when [MR-CH 3] and [MR-CH 4] keys are assigned.
e When receiving a call, adjust the audio output level to a comfortable listening level.

Transmitting:

Wait for the channel to become clear to avoid interference. q While pushing and holding [PTT], speak into the microphone at a normal voice level.
When a tone signalling system is used, the call procedure described on p. 13 may be necessary.
w Release [PTT] to return to receive. IMPORTANT!: To maximize the readability of your signal; 1. Pause briey after pushing [PTT]. 2. Hold the microphone 5 to 10 cm (2 to 4 inches) from your mouth, then speak into the microphone at a normal voice level.

Page 15 (1,1)

D Transmitting notes
Transmit inhibit function The transceiver has several inhibit functions which restrict transmission under the following conditions: - The channel is in mute condition. - Channel is busy. - Un-matched (or matched) CTCSS is received. - The selected channel is a receive only channel. Time-out timer After continuous transmission for the pre-programmed time period, the time-out timer activates, and causes the transceiver to stop transmitting. Penalty timer Once the time-out timer activates, transmission is further inhibited for a period determined by the penalty timer.

D DTMF transmission

If the transceiver has [DTMF Autodial] assigned to it, the automatic DTMF transmission function is available. Push [DTMF Autodial] to transmit the DTMF code.

Page 16 (1,1)

I Scrambler function
The optional voice scrambler units UT-109 (#01) and UT-110 (#01) provide high performance private communication between stations with the same scrambler codes. Push and hold [Scrambler] to turn the scrambler function ON. Push [Scrambler] to turn the scrambler function OFF.
I Setting the squelch level
The squelch circuit mutes the received audio signal depending on the signal strength. q While pushing [PTT] and [Lower], rotate [VOL] to turn the power ON to enter the squelch level adjustment mode. w Push [Upper] to increase the [Upper] squelch level (tight squelch) or [PTT] [Lower] to decrease the squelch level (loose squelch). [Lower] e Rotate [VOL] to turn the power OFF to x the squelch level.

Page 17 (1,1)

I Man Down Emergency Call
The man down emergency call function transmits an emergency call automatically, after the transceiver laying down in a horizontal position for a pre-set time period. (The optional UT-113 MAN DOWN UNIT is required.) After the emergency call, the transceiver performs transmission and reception alternately with the following conditions: - Transmits the microphone signals. - Receives the signal and emits audio. When the emergency cancel code is received, the function is cancelled. IMPORTANT!: Set an emergency channel individually, to provide certain emergency call operation is recommended.

Page 18 (1,1)

OPTIONAL UNIT INSTALLATION I Optional unit installation
Install the optional unit as follows: q Rotate [VOL] to turn the power OFF, and remove the battery pack. (p. 3) w Remove the unit cover. NOTE: Use a flat head screw driver or a similar flat instrument, and insert into the hollow of the chassis, then lift and take away the unit cover. (The removed cover cannot be used again.)
e Install the unit as shown below.
*This illustration is described with the UT-110.
r Replace the unit cover and the battery pack, then rotate [VOL] to turn the power ON. NOTE: The optional UT-109/UT-110 SCRAMBLER UNITS requires some PC board modications. Please refer to the additional installation as at right.

Page 19 (1,1)

OPTIONAL UNIT INSTALLATION
I Scrambler unit installation
The following PC board modication is required when installing the optional UT-109 or UT-110. q Rotate [VOL] to turn the power OFF, and remove the battery pack. (p. 3) w Remove the unit cover as shown at left (Optional unit installation.) e Cut the pattern on the PCB at the TX mic circuit (MIC) and RX AF circuit (DISC) as shown below. r Install the scrambler unit as shown at left (Optional unit installation.) t Replace the unit cover and the battery pack, then rotate [VOL] to turn the power ON.
NOTE: When uninstalling the scrambler unit Be sure to re-solder the disconnected points at left, otherwise no TX modulation or AF output is available.

Page 20 (1,1)

BATTERY CHARGING

I Battery charging

Prior to using the transceiver for the rst time, the battery pack must be fully charged for optimum life and operation. CAUTION: To avoid damage to the transceiver, turn it OFF while charging. Recommended temperature range for charging: +10C to +40C (+50F to +104F) - The Li-Ion battery functions within 20C to +60C (4F to +140F) Use the specified chargers (BC-119N, BC-121N and BC-160). NEVER use another manufacturers charger. Use the optional AC adapter. NEVER use another manufacturers AC adapter.

Recommendation: Charge the supplied battery pack for a maximum of up to 10 hours. Li-Ion batteries are different from Ni-Cd batteries in that it is not necessary to completely charge and discharge them to prolong the battery life. Therefore, charging the battery in intervals, and not for extended periods is recommended.

Page 21 (1,1)

I Caution
R DANGER Charge the specied Icom batteries only.
Only tested and approved for use with genuine Icom batteries. Fire and/or explosion may occur when a third party battery pack or counterfeit product is charged.
CAUTION! NEVER insert battery pack/transceiver (with the battery pack attached) with wet or soiled into the charger. This may result in corrosion of the charger terminals or damage to the charger. The charger is not waterproof and water can easily get into it.
NEVER incinerate used battery packs. Internal battery gas may

cause an explosion.

NEVER immerse the battery pack in water. If the battery pack becomes wet, be sure to wipe it dry immediately (particularly the battery terminals) BEFORE attaching it to the transceiver. Otherwise, the terminals will become corroded, or cause connection failure, etc. NEVER short the terminals of the battery pack. Also, current may ow into nearby metal objects, such as a necklace, etc. Therefore, be careful when carrying with, or placing near metal objects, carrying in handbags, etc. AVOID leaving the battery pack in a fully charged, or completely
discharged condition for long time. It causes shorter battery life. In case of leaving the battery pack unused for a long time, it must be kept safely after discharge, or use the battery until the battery indicator appears, then remove it from the transceiver. If your battery pack seems to have no capacity even after being charged, fully charge the battery pack again. If the battery pack still does not retain a charge (or very little), a new battery pack must be purchased.

Page 22 (1,1)

I Optional battery chargers
D Rapid charging with the BC-160
The optional BC-160 provides rapid charging of optional Li-Ion battery packs. An AC adapter (may be supplied with BC-160 depending on version) or the DC power cable (OPC-515L/CP-17L) is additionally required.

Battery pack AC adapter (Not supplied with some versions.) Transceiver

Turn power OFF

Optional OPC-515L (for 13.8 V power source) or CP-17L (for 12 V cigarette lighter socket) can be used instead of the AC adapter.
IMPORTANT!: Ensure the guide lobs on the battery pack are correctly aligned with the guide rails inside the charger adapter.

Guide rail

Page 23 (1,1)

AD-106 installation

q Install the AD-106 desktop charger adapter into the holder space of the BC-119N/121N.
Desktop charger adapter Connectors
w Connect the plugs of the BC-119N/BC-121N to the AD-106 with the connector, then install the adapter into the charger with the supplied screws.
Screws supplied with the charger adapter

Page 24 (1,1)

D Rapid charging with the BC-119N+AD-106
The optional BC-119N provides rapid charging of optional Li-Ion battery packs. The following items are additionally required: One AD-106 (purchase separately). An AC adapter (may be supplied with BC-119N depending on version) or the DC power cable (OPC-515L/CP-17L).

Transceiver

Battery pack AC adapter (Not supplied with some versions.)
AD-106 charger adapter is installed in BC-119N. Optional OPC-515L (for 13.8 V power source) or CP-17L (for 12 V cigarette lighter socket) can be used instead of the AC adapter.
IMPORTANT!: Ensure the guide lobs on the battery pack are correctly aligned with the guide rails inside the charger adapter. Guide rails

Page 25 (1,1)

D Rapid charging with the BC-121N+AD-106
The optional BC-121N allows up to 6 battery packs to be charged simultaneously. The following items are additionally required. Six AD-106. An AC adapter (BC-157) or the DC power cable (OPC-656)
Battery pack AD-106 charger adapters are installed in each slot. AC adapter (Purchase separately)
DC power cable (OPC-656) (Connect with the DC power supply; 13.8 V/at least 7 A)

Guide rails

Page 26 (1,1)

SWIVEL BELT CLIP

I MB-93 contents
Qty. q Belt clip 1 w Base clip 1

I To attach

q Release the battery pack if it is attached. (p. 3) w Slide the base clip in the direction of the arrow until the base clip is locked and makes a click sound.

Page 27 (1,1)

e Clip the belt clip to a part of your belt. And insert the transceiver into the belt clip until the base clip inserted fully into the groove.

r Once the transceiver is locked in place, it swivels as illustrated below.

Page 28 (1,1)

I To detach
q Turn the transceiver upside down in the direction of the arrow and pull out from the belt clip.

Page 29 (1,1)

w Release the battery pack if it is attached. (p. 3) e Pinch the clip (q), and slide the base clip in the direction of the arrow (w).

CAUTION:

HOLD THE TRANSCEIVER TIGHTLY, WHEN HANGING OR DETACHING THE TRANSCEIVER FROM THE BELT CLIP. Otherwise the transceiver may not be attached to the holder or swivel properly if the transceiver is accidentally dropped and the base clip is scratched or damaged.

Page 30 (1,1)

OPTIONS
Voltage 7.4 V 7.4 V Capacity 980 mAh 2000 mAh Battery life* 9 hrs. 18 hrs.

D BATTERY PACK

Battery pack BP-230N BP-232N
* When the power save function is turned ON, and the operating periods are calculated under the following conditions; TX : RX : standby = 5 : 5 : 90

D CHARGERS

BC-119N DESKTOP CHARGER + AD-106 CHARGER ADAPTER + BC-145 AC ADAPTER For rapid charging of battery packs. An AC adapter is supplied with the charger depending on versions. Charging time: approx. 3 hours when BP-232N is attached. BC-121N MULTI-CHARGER + AD-106 CHARGER ADAPTER (6 pcs.) + BC-157 AC ADAPTER For rapid charging of up to 6 battery packs (six AD-106s are required) simultaneously. An AC adapter should be purchased separately. Charging time: approx. 3 hours when BP-232N is attached. BC-160 DESKTOP CHARGER + BC-145 AC ADAPTER For rapid charging of battery packs. An AC adapter is supplied with the charger depending on versions. Charging time: approx. 3 hours when BP-232N is attached.

Page 31 (1,1)

D OPTIONAL UNITS
UT-108 DTMF DECODER UNIT Provides pager and code squelch capabilities. UT-109 (#01)/UT-110 (#01) SCRAMBLER UNITS Non-rolling type (UT-109)/Rolling type (UT-110) voice scrambler unit provides higher communication security. UT-113 MAN DOWN UNIT Provides a measure of safety when working in a hazardous environment, etc.

D BELT CLIPS

MB-93 SWIVEL BELT CLIP MB-94 BELT CLIP Exclusive alligator-type belt clip. The same as supplied with the transceiver. MB-96*/96F LEATHER BELT HANGER *MB-93s base clip is required.

D DC CABLES

CP-17L CIGARETTE LIGHTER CABLE Allows charging of the battery pack through a 12 V cigarette lighter socket. (For BC-119N) OPC-515L/OPC-656 DC POWER CABLES Allows charging of the battery pack using a 13.8 V power source instead of the AC adapter. OPC-515L: For BC-119N OPC-656 : For BC-121N

D OTHER OPTIONS

SP-13 EARPHONE Provides clear receive audio in noisy environment. HM-131L SPEAKER-MICROPHONE Combination speaker-microphone that provides convenient operation while hanging the transceiver from your belt. HM-131L has a moisture proof construction.

Page 32 (1,1)

HS-94/HS-95/HS-97 HEADSET + VS-1L VOX/PTT CASE HS-94: Ear hook type HS-95: Neck-arm type HS-97: Throat microphone VS-1L: VOX/PTT switch box for hands-free operation, etc. FA-SC73US/FA-SC56VS/FA-SC57VS STUBBY ANTENNAS FA-SC73US: 450490 MHz FA-SC56VS: 150162 MHz FA-SC57VS: 160174 MHz FA-SC01U/FA-SC25U/FA-SC57U/FA-SC72U/FA-SC25V/ FA-SC55V ANTENNAS FA-SC01U: 350400 MHz FA-SC25U: 400430 MHz FA-SC57U: 430470 MHz FA-SC72U: 470520 MHz FA-SC25V: 136155 MHz FA-SC55V: 146174 MHz
Some options may not be available in some countries. Please ask your dealer for details.

Page 33 (1,1)

About VS-1L VOX/PTT CASE
The VS-1L is a VOX/PTT unit for Icom handheld transceivers, and allows you hands-free operation. An optional headset (HS-94, etc.) is additionally required for operation.
The VOX (voice operated transmission) function starts transmission without pushing PTT switch when you speak into the microphone; then, automatically returns to receive when you stop speaking.
Features Straight type head SP/MIC plug equipped Water resistant construction Durable construction Equipped with a PTT switch and revolving clip. MIC/VOX gain adjustment 1 Remove the water protection cover on the right side of the VS-1L. 2 Adjust the MIC/VOX gain with a thin screw driver. Clockwise rotation increases the MIC/VOX gain. 3 Return the protective cover back to the MIC/VOX gain adjustment hole.

Adjusting pot

VS-1L PTT switch
Water protection cover VOX PTT

Page 34 (1,1)

A-6369D-1EX-y Printed in Japan 20042006 Icom Inc.
1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan