Important Information

For your Condenser dryer to operate efficiently, you must follow the regular maintenance schedule shown below:

Fluff Filter.

! You MUST clean the fluff filter after EVERY drying cycle. STEP 1. Open the door of your dryer. STEP 2. Pull out the filter (using the two finger grips). STEP 3. Clean any fluff deposits from the filter mesh. STEP 4. Refit the filter - NEVER run the dryer without the filter in position.
! Failure to clean the filter after EVERY drying cycle will affect the drying performance of your machine. - It will take longer to dry and as a result will use more electricity during drying.

Water Container.

! You MUST empty the water container after EVERY drying cycle. STEP 1. Pull the water container towards you and remove it fully from the dryer. STEP 2. Empty all the water collected in the water container. STEP 3. Refit the water container, ensuring that it is pushed fully back into position. ! The Empty Water light stays on - To remind you to empty the water container at the start and at the end of each programme.
! Failure to empty the water container will result in: - The machine will stop heating (so the load may still be wet at the end of the drying cycle). - The Empty Water light will flash to tell you that the water container is full.
Priming the Water Collection System
When your dryer is new, the water container will not collect water until the system is primed. this will take 1 or 2 drying cycles. Once primed it will collect water during every drying cycle.

Condenser Unit.

! You MUST clean the fluff from the condenser EVERY month. STEP 3. Flush the condenser, from the rear with water, to remove any fluff deposits. STEP 4. Refit the condenser unit - ensure that the unit is pushed in fully, all 3 clips are re-secured and the positiong arrows on the front of the condenser are pointing upwards.
STEP 1. Open the condenser cover - hold the handle and pull towards you.
STEP 2. Remove the condenser by rotating the 3 clips then pulling the condenser towards you. (There may be some water in the tubes, this is normal).
Check that: - The positioning arrows are pointing upwards. - The 3 clips are re-secured back into their lock position.
Rotate 3 clips ! Failure to clean the condenser could cause premature failure of your dryer.

Instruction booklet

TUMBLE DRYER

English

Contents

Installation, 5

Door reversal instructions Where to put your dryer Ventilation Water drain Electrical connection Before you start using your dryer

Dryer description, 6

To open the door The features Control panel
Start and programmes, 7-9

ISL70C

Choosing a programme Table of programmes The controls

Laundry, 10-11

Sorting your laundry Wash care labels Special clothing items Drying times
Warnings and Suggestions, 12
General safety Disposal Saving energy and respecting the environment

Maintenance and Care, 13

Switching off the electricity Cleaning the filter after each cycle Empty the water container after each cycle Check the drum after each cycle Cleaning the condenser Cleaning the dryer
Troubleshooting, 14 Service, 15

Spare parts

! Keep this instruction booklet on hand in order to refer to it when necessary. Take it with you when you move, and should you sell this appliance or pass it on to another party, make sure that this booklet is supplied along with the dryer so that the new owner may be informed about warnings and suggestions on how the appliance works. ! Read these instructions carefully; the following pages contain important information on installation and suggestions on how the appliance works.

Installation

Where to put your dryer
Place your dryer at a distance from gas ranges, stoves, heaters, or cook tops because flames can damage the appliance. Minimum gap 10mm q If you are going to install the appliance under a work counter, be sure to leave a 10mm space between the Minimum gaps top and any other objects 15mm on or above the machine and a 15mm space between the sides and lateral furnishings or walls. This is to ensure proper air circulation. ! Make sure that the back vents are not obstructed.

Electrical connections

Make sure of the following before you insert the plug into the the electrical socket:
Ensure your hands are dry. The socket must be grounded. q The socket must be able to sustain the machines maximum power, which is indicated on the rating label (see Dryer Description). q Power voltage must be within the values indicated on the rating label (see Dryer Description). q The socket must be compatible with the dryers plug. Should this not be the case, replace the plug or the socket. ! Do not use extension cords. ! The dryer must not be installed outdoors, even if the space is sheltered. It can be very dangerous if it is exposed to rain or storms. ! Once installed, the dryers electrical wire and plug must be within easy reach. ! The power cord must not be bent or squashed. ! The power cord supplied is fitted with a BS1363 plug and a 13 amp BS1362 fuse. If you need to replace the fuse, use only those rated at 13 amp (13A) and ASTA approved to BS1362.

Ventilation

When the dryer is in use, there has to be adequate ventilation. Make sure you put your dryer in an environment that is not damp and has proper air circulation throughout. Airflow around the dryer is essential to condense the water produced during the washing, the dryer will not operate efficiently in an enclosed space or cupboard. ! If using the dryer in a small or cold room some condensation could be experienced. ! We do not recommend that the dryer is installed in a cupboard but the dryer must never be installed behind a lockable door, a sliding door or a door with a hinge on the opposite side to that of the dryer door.
Moulded plug ! The plug must not be used without the fuse cover in place. If a replacement fuse holder/cover is required, it must be of the same colour coding or wording as shown on the base of the plug. Replacements are available from authorised dealers. Changing the plug The wires in the power cord are coloured in accordance with the following:
Green and Yellow (Earth) wire to terminal marked E, symbol , or coloured green and yellow. Blue (Neutral) wire to terminal marked N or coloured black. Cord clamp
Door Reversal Instructions
Hinge Door latch Door catch
13A ASTA approved fuse to BS1362. Brown (Live) wire to terminal marked L or coloured red.

The door of your dryer is reversible and can easily be changed. Exchange diagonally hinge brackets and blanking screws. Exchange door latch and catch with their opposite blanking plates (see diagram above).

Water drain

If your dryer is installed next to a drain the water can be plumbed into this drain. This does away with the need to empty the water container. (see Plumbing your Dryer).
! If the plug being replaced is a non-rewirable type, then the cut-off plug must be disposed of safely. DO NOT leave it where it can be inserted into a socket and create a shock hazard. ! The power supply cord should be checked periodically and replaced by a cord specially prepared for this dryer and fitted only by authorised technicians (see Service). New or longer power cords are supplied at an extra charge by authorised dealers. ! The manufacturer denies any responsibility should any of these rules not be followed. ! If in doubt about any of the above consult a qualified electrician.
Before you start using your dryer
Once you have installed your dryer and before you use it, clean the inside of the drum to remove any dust that could have accumulated during transport.

Dryer Description

To open the door
Press and release the front panel in position shown

The features

Water container Rating plate
Model & Serial numbers
Condenser unit (cover open)
Condenser cover Condenser cover handle (Pull to open) Filter

Air intake grille

Control panel
Progress or Delay Lights START/CANCEL Button Empty Water Light On/Off Light ON/OFF Button

Programmes Guide

OPTION Buttons and lights

Indicator

PROGRAMMES Knob
The START/CANCEL button starts a selected programme. When you press this button there will be one beep and the progress lights will flash to confirm the action. If you have not set a programme, the buzzer will beep four times. When a programme is running, holding this button in cancels the programme and stops the dryer (see Start and Programmes). The OPTION buttons/lights select available options for your selected programme (see Start and Programmes). The lights indicate that the option has been selected. The Programmes Guide allows you to consult a user friendly table of the available programmes. The Empty Water light signals that the water container should be emptied. When it is flashing it indicates that the container is full. The light will take a few seconds to go out after replacing the empty container, the dryer must be running for this to happen (see The Controls).

Note: If the water container fills the light flashes, the heat is turned off and your laundry will not dry. The On/Off indicator light signals that your dryer is in use or ready to select a programme. If this light flashes it indicates there is a fault (see Troubleshooting). The ON/OFF button : If the dryer is running and this button is pressed, the dryer stops. Press again, the dryer restarts. The Progress or Delay lights show you the status of the programme, or the delay time when they flash. During a delayed start the lights will flash to show the delay selected. When (not flashing) they show each stage of the programme by the corresponding light turning on (see Start and Programmes). The PROGRAMMES knob sets the programme: rotate it until the indicator is pointing to the programme you want to select (see Start and Programmes).

Start and Programmes

Choosing a programme
1. Plug the dryer into the electrical socket. 2. Sort your laundry according to fabric type (see Laundry). 3. Open the door and make sure the filter is clean and in place and the water container is empty and in place (see Maintenance). 4. Load the machine and make sure items are not in the way of the door seal. Close the door. 5. If the On/Off light is not lit: Press the ON/OFF button. 6. Choose a programme by checking the Programmes Guide (see Programmes) as well as the indications for each type of fabric (see Laundry). - Select a programme by rotating the PROGRAMMES knob. 7. Set a delay time and other options if necessary. 8. If you wish to select the buzzer sound, at the end of the programme, press the ALARM Option button. 9. Press the START button to begin. During the drying programme, you can check on your laundry and take out items that are dry while others continue drying. When you close the door again, press the START button in order to resume drying. 10. During the last few minutes of Drying Programmes, before the programme is completed, the final COOL TUMBLE phase is entered (fabrics are cooled), this phase should always be allowed to complete. 11. When the programme is complete. The buzzer will sound, if this option selected. Open the door, take the laundry out, clean the filter and replace it. Empty the water container and replace it (see Maintenance). If you do not take out the laundry immediately, the dryer will tumble occasionally for 10 hours or until you open the door. 12. Unplug the dryer.

Easy Iron Programme

Easy Iron is a short 10 minute programme (8 minutes of heat followed by a 2 minute cool tumble period) which fluffs the fibres of clothing that have been left in the same position/location for an extended period of time. The cycle relaxes the fibres and makes them easier to iron and fold. ! Easy Iron is not a drying programme and should not be used for wet articles of clothing. For best results: 1. Do not load more than the maximum capacity. These numbers refer to the dry weight: Fabric Maximum load Cotton and Cotton mixtures 2.5kg Synthetics 2kg Denim 2kg 2. Unload the dryer immediately after the end of the programme, hang, fold or iron the articles and put them away in the closet. Should this not be possible repeat the programme. The Easy Iron effect varies from one fabric to the next. It works well on traditional fabrics like Cotton or Cotton mix, and less well on acrylic fibres and on materials such as Tencel.

Sport programme

Special shoes This is a programme to dry one pair of sports shoes sized 37-46 (4-11). q The shoes must have been washed and spun at a minimum spin speed of 400rpm. q They must be used with the shoe rack provided. If you tumble shoes in the drum you will damage your dryer. q Remove the filter from its position in the front of the dryer and fit the rack. q Tuck the laces inside the shoes and load shoes with toes down and soles facing you. q Drying times will vary dependant on the size and style of shoe. If shoes are not completely dry at the end of the programme, run the programme again. ! Do not dry shoes with Gel inserts or flashing lights. ! Only dry shoes made from Synthetics or Canvas materials. ! When finished remove shoe rack and replace the filter. Special sports q This is a programme for tumble dryer safe garments, such as Tracksuits and Shorts marked with the symbol. q It can be used for load sizes up to 1.5kg q We recommend that garments are turned inside out before drying. q This programme will take up to 130 minutes. The actual time will vary depending on the size and density of the load and the spin speed used in your washer. q Loads dried using this programme are usually ready to wear, but on some heavier garments the edges may be slightly damp.

Programmes

! If the On/Off light is not lit; Press the ON/OFF button and then select programme.

Programme

1 Cottons

Cupboard Dry

What it does.
Dries your clothes on High heat setting, ready for putting away Dries your clothes on High heat setting, ready for hanging. Dries your clothes on High heat setting, ready for ironing. Dries your clothes on High heat setting, ready for putting away. Dries your clothes on High heat setting, ready for hanging. Dries your clothes on High heat setting, ready for ironing.

How to set it.

1. Position the PROGRAMME knob on 1. Options available: 2. Select any Options, if required. Alarm 3. Press the START button. Delayed start 1. Position the PROGRAMME knob on 2. Options available: 2. Select any Options, if required. Alarm 3. Press the START button. Delayed start 1. Position the PROGRAMME knob on 3. Options available: 2. Select any Options, if required. Alarm 3. Press the START button. Delayed start 1. Position the PROGRAMME knob on 4. Options available: 2. Select any Options, if required. Alarm 3. Press the START button. Delayed start 1. Position the PROGRAMME knob on 5. Options available: 2. Select any Options, if required. Alarm 3. Press the START button. Delayed start 1. Position the PROGRAMME knob on 6. Options available: 2. Select any Options, if required. Alarm 3. Press the START button. Delayed start 1. Position the PROGRAMME knob on 7. Options available: 2. Select any Options, if required. Alarm 3. Press the START button.

2 Cottons

Hanger Dry

3 Cottons

Ready to Iron

4 Synthetics

5 Synthetics

6 Synthetics

7 Dries your shoes on Low Special Shoes heat setting, ready to be worn (see previous page).
Dries your sports clothes on 1. Position the PROGRAMME knob on 8. Options available: 8 Special Sports Low heat setting, ready to be 2. Select any Options, if required. Alarm 3. Press the START button. worn (see previous page). Delayed start 9 Delicate

eg. Acrylics

Dries your clothes on Low heat setting, ready to be worn.
1. Position the PROGRAMME knob on 9. Options available: 2. Select any Options, if required. Alarm 3. Press the START button. Delayed start

10 Easy Iron

1. Position the PROGRAMME knob on 10. Brief programme (approximately 10 minutes) 2. Select any Options, if required. that softens fibres of clothing 3. Press the START button that is ready for ironing. Dries wet clothing that you wish to dry on low heat or small loads (less than 1kg). Can be used with high heat option if you prefer to use a timed programme. 1. Position the PROGRAMME knob on the desired time: 160, 120, 80 or 40. 2. Select any Options, if required. 3. Press the START button.

Timed Drying (160, 120, 80 or 40 minutes)
! This is not a drying programme (see previous page). Options available: Alarm Options available: Alarm , High Heat , Delayed Start. Consult suggested drying times (see Laundry). The last 10 minutes of these programmes is the Cool Tumble (see below).

Cool Tumble

Brief programme (approximately 10 minutes) that cools fibres or clothing.
1. Position the PROGRAMME knob on 2. Select any Options, if required. 3. Press the START button.

. Options available:

The Controls PROGRAMMES knob
! Warning, if after pressing the start button, the programmes knob position is changed, the new position will NOT change the programme selected. ! Position 0, turning the knob to position 0 resets and cancels a programme.

OPTION buttons / lights

These buttons are used to customise the selected programme to your requirements. A programme must have been selected on the programme knob before an option can be selected. Not all options are available for all programmes (see Start and Programmes). If an option is not available and you press the button, the buzzer will beep four times. If the option is available there will be one beep and the option light above the button lights to confirm the selection. After the start button has been pressed only the Alarm option can be changed. Progress (Drying, CoolTumble, Post Creasecare) / Delay (3hr 6hr 9hr 12hr) Lights When the light above the delay button is on, these lights flash to indicate the delay time is selected. During other programmes they indicate the progress of the dryer, each one comes on as the corresponding phase starts. Time Delay The start of some programmes (see Start and Programmes) can be delayed for up to 12 hours in 3hr steps. Ensure the water bottle is emptied before setting a delayed start. When a delayed start is in progress the light above the delay button will be on and the selected delay period light will flash (after the start button has been pressed). To set a delayed start, press the Time Delay button, and the light above the button will come on together with the 3hr delay light. Pressing the button again will advance the delay setting to 6hr, the 3hr light goes out and the 6hr light is on. Each time you press the button the delay setting advances 3 hours, as indicated by the corresponding light. If the 12hr light is on, pressing the button again will cancel the delay. You can also cancel the delay by turning the programmes knob to 0, wait for the buzzer to beep and then turn back to your selected programme. Pre Creasecare When a delayed start has been selected, the clothes are tumbled occasionally during the delayed period to help prevent creases developing. High Heat When available this button selects high heat. Press this button and a high heat setting is selected and the light above the button comes on. Timed programmes have a default of low heat, if the light alongside the button is on then pressing the button selects a low heat setting and the light goes out.

Alarm Available on all programmes and allows the buzzer to give a signal at the end of the drying cycle, to remind you that the clothes are ready to be removed. Press the button and the light will show that the option is selected. Post Creasecare The clothes are occasionally tumbled after the end of the drying and cool tumble cycles, to help prevent creases developing should you not be available to remove the load immediately the programme is complete. Empty Water Light / Container (If you have plumbed your dryer to a drain this light can be ignored, as there is no need to empty the water container). When this light is on (not flashing) it reminds you to empty the water container. If the water container fills during a programme, the heater turns off and the dryer does a period of Cool Tumble then the light flashes and the buzzer sounds. After this it stops and all 3 progress lights and the 3hr delay light come on and the empty water light flashes. You must empty the water container and restart the dryer or the clothes will not dry. After re-starting the dryer, the light will take a few seconds to go out. To avoid this always empty the water container each time you use the dryer (see Maintenance).

Door Opening

Opening the door during a programme will stop the dryer and have the following effects: q All 3 progress lights and the 3hr delay light come on. q During a delay phase the delay will continue to count down. The start button must be pressed to resume the delay programme. One of the delay lights will flash to show the current delay setting. q The start button must be pressed to resume the programme. The progress lights will change to show the current status. q During the cool tumble or post creasecare phase of a drying programme and anytime during an Airing or Cool Tumble programme, the programme will finish. Pressing the start button will re-start a new programme at the beginning. q Changing the programmes knob will select a new programme, after you press the start button. You can use this to select the Cool Tumble programme to cool the clothes, if you find them dry enough.

Note If you have a power cut, switch off the power or remove the plug. When the power is restored, press the START button and the programme will resume.

Laundry

Sorting your laundry
Check symbols on clothing labels to make sure that the articles can be tumble dried. q Sort laundry by fabric type. q Empty pockets and check buttons. q Close zippers and hooks and tie loose belts and strings. q Wring out each item in order to eliminate as much excess water as possible. ! Do not load dripping wet clothes into the dryer.
Wash Care Labels Look at the labels on your garments, especially when tumble drying for the first time. The following symbols are the most common: May be tumble dried Do not tumble dry Tumble dry at high heat setting Tumble dry at low heat setting
Maximum load size Do not load more than maximum capacity. These numbers refer to dry weight: Natural fibres: 7kg max (15lb) Synthetic fibres: 3kg max (6.6lb) ! DO NOT overload the dryer as this could result in reduced drying performance.
Items not suitable for tumble drying

Typical weights

Note: 1kg = 1000g 1lb = 16oz Clothes Blouse Cotton 150g Other 100g Dress Cotton 500g Other 350g Jeans 700g 10 nappies 1000g Shirt Cotton 300g Other 200g T-Shirt 125g Household Items Duvet cover Cotton (Double) Other Large Tablecloth Small Tablecloth Tea Towel Bath Towel Hand Towel Double Sheet Single Sheet
5oz 3oz 1lb 2oz 12oz 1lb 6oz 2lb 3oz 10oz 7oz 4oz
Articles that containing rubber or rubber-like materials or plastic film (pillows, cushions, or PVC rainwear), any other flammable articles or objects that contain flammable substances (towels soiled with hair spray). Glass fibres (certain types of draperies) Items which have been dry cleaned Items with the ITCL Code (see Special clothing items). These can be cleaned with special at-home dry cleaning products. Follow instructions carefully. Large bulky items (quilts, sleeping bags, pillows, cushions, large bedspreads etc). These expand when drying and would prevent airflow through the dryer.
1500g 1000g 700g 250g 100g 700g 350g 500g 350g
3lb 5oz 2lb 3oz 1lb 6oz 9oz 3oz 1lb 6oz 12oz 1lb 2oz 12oz
At the end of a drying cycle, cottons could still be damp if you grouped cottons and synthetics together. If this happens simply give them an additional short period of drying. q Note: The last 10 minutes of any time set is the Cool Tumble, so allow for this when setting the time, as this period will not dry your laundry.

Special clothing items

Blankets and Bedspreads: acrylic items (Acilan, Courtelle, Orion, Dralon) must be dried with special care on LOW heat setting. Avoid drying for a long period of time. Pleated or creased garments: read the manufacturers drying instructions on the garment. Starched articles: do not dry these with non-starched items. Make sure that as much of the starch solution is removed from the load as possible before placing it in the dryer. Do not over-dry: the starch will become powdery and leave your clothing limp, which defeats the purpose of starch.

Recycling and disposal information
As part of our continued commitment to helping the environment, we reserve the right to use quality recycled components to keep down customer costs and minimise material wastage. q Disposing of the packaging material: follow local regulations, so the packaging can be recycled. q To minimise risk of injury to children, remove the door and plug - then cut off mains cable, flush with the appliance. Dispose of these parts separately to ensure that the appliance can no longer be plugged into a mains socket.
Disposal of old electrical appliances
The European Directive 2002/96/EC on Waste Electrical and Electronic Equipment (WEEE), requires that old household electrical appliances must not be disposed of in the normal unsorted municipal waste stream. Old appliances must be collected separately in order to optimise the recovery and recycling of the materials they contain and reduce the impact on human health and the environment. The crossed out wheeled bin symbol on the product reminds you of your obligation, that when you dispose of the appliance it must be separately collected. Consumers should contact their local authority or retailer for information concerning the correct disposal of their old appliance.
Saving energy and respecting the environment
Wring out items to eliminate excess water before tumble drying (if you use a washing machine first, select a high spin cycle). Doing this will save time and energy during drying. Always dry full loads - you save energy: single items or small loads take longer to dry. Clean the filter after each use to contain energy consumption costs (see Maintenance).

Maintenance and Care

Switching off the electricity
! Unplug your dryer when not using it, when cleaning it and during all maintenance operations.

Cleaning the drum

! Do not use abrasives, steel wool or stainless steel cleaning agents to clean the drum. A coloured film may start to appear on the stainless steel drum, this may be caused by a combination of water and, or cleaning agents such as fabric conditioner from the wash. This coloured film will not affect the dryer performance.
Clean the filter after each cycle
The filter is an important part of your dryer: it accumulates lint and fluff that is formed while drying. When finished drying, clean the filter by rinsing it under running water or with your vacuum cleaner. Should the filter become clogged up, the airflow inside the dryer will be seriously compromised: drying times lengthen and you will consume more energy. It may also damage your dryer. The filter is found in front of the dryer trim (see diagram). Removing the filter: 1. Pull the plastic grip of the filter upwards (see diagram). 2. Clean the filter and replace it correctly. Ensure the filter is fully located flush into the tumble dryer trim. ! Do not use the dryer without replacing the filter.

Cleaning the condenser unit
Periodically (every month) remove the condenser unit and clean any build up of fluff from between the plates by rinsing it under the tap with cold water. This should be done with cold water from the rear of the condenser. Removing the condenser: 1. Unplug the dryer and open the door. 2. Pull open the condenser cover (see diagram). Release the three catches by turning 90 counterclockwise then pull on the grip and remove from the dryer. 3. Clean the surface of the seals and replace, making sure that the catches have been secured.
Empty the water container after each cycle
Pull the container out of the dryer and empty it into a sink or other suitable drain. Replace the water container securely. Always check and empty the container before you start a new drying programme.

Cleaning the dryer

External parts in metal or plastic and rubber parts can be cleaned with a damp cloth. q Periodically (every 6 months) vacuum the front air intake grille and vents at the rear of the dryer, to remove any build up of fluff, lint or dust. Also to remove accumulation of fluff from the front of the condenser and filter areas, clean occasionally with a vacuum cleaner. ! Do not use solvents or abrasives. ! Your dryer uses special bearing components which do not need lubrication. ! Have your dryer checked regularly by authorised technicians to ensure electrical and mechanical safety (see Service).
Check the drum after each cycle
Turn the drum manually in order to remove small items (handkerchiefs) that could have been left behind.

Water container

Filter
Front Condenser unit Condenser cover Catches Handle

Air intake

Condenser unit

Troubleshooting

One day your dryer seems not to be working. Before you call your Service Centre (see Service), go through the following troubleshooting suggestions:

Problem:

The tumble dryer wont start.
Possible causes / Solution:

q q q q

The plug is not plugged into the socket, or not making contact. There has been a power failure. The fuse has blown. Try to plug another appliance into the socket. You are using an extension cord? Try to plug the dryers power cord directly into the socket. The door is not closed securely? The PROGRAMMES knob has not been set properly (see Start and Programmes). The START button has not been pressed (see Start and Programmes). You have set a delayed time (see Start and Programmes). The filter has not been cleaned (see Maintenance). The water container needs emptying? The empty water light is flashing? (see Maintenance). The condenser needs cleaning? (see Maintenance). The temperature setting is not ideal for the type of fabric you are drying (see Start and Programmes, and see Laundry). The correct drying time has not been selected for the load (see Laundry). The air intake grille or rear vents are obstructed (see Installation, and see Maintenance). The items were too wet (see Laundry). The dryer was overloaded (see Laundry). The water container was probably not emptied at the start of the programme. Do not wait for the empty water signal, always check and empty the container before starting a new drying programme (see Maintenance). This is normal, the light flashes when the container is full. If the light is on but not flashing it is just a reminder to empty the container (see Start and Programmes). If the ON/OFF light flashes together with the Time Delay and High Heat lights; Or the ON/OFF light flashes together with the Time Delay, Alarm, High Heat and Empty Water lights, then: - Turn off and remove the plug. Clean the filter and the condenser (see Maintenance). Then replace the plug, turn on and start another programme. If the same combination of lights still flash contact the Service Centre (see Service). If any other combination of lights flash: Note down the other lights that are flashing and contact the Service Centre (see Service).

This appliance conforms to the following EC Directives: - 2006/95/EC (Low Voltage Equipment) - 89/336/EEC, 92/31/EEC and 93/68/EEC (Electromagnetic Compatibility)

195042640.06W

05/2007 - SIMLEX. Four Ashes, Wolverhampton