Instructions for use

WASHER-DRYER Contents

English,1

Installation, 2-3-4-5
Unpacking and levelling, 2 Electric and water connections, 2-3 The first wash cycle, 4 Technical details, 5
Washer-dryer description, 6-7

Control panel, 6 Leds, 7

Starting and Programmes, 8
Briefly: how to start a programme, 8 Programme table, 8

Personalisations, 9

WIDL 146
Setting the temperature, 9 Setting the drying cycle, 9 Functions, 9 Detergent dispenser, 10 Preparing your laundry, 10 Special items, 10
Detergents and laundry, 10
Precautions and advice, 11
General safety, 11 Disposal, 11 Saving energy and respecting the environment, 11

Care and maintenance, 12

Cutting off the water or electricity supply, 12 Cleaning your appliance, 12 Cleaning the detergent dispenser, 12 Caring for your appliance door and drum, 12 Cleaning the pump, 12 Checking the water inlet hose, 12
Troubleshooting, 13 Service, 14
Before calling for Assistance, 14

Installation

Keep this instruction manual in a safe place for future reference. Should the appliance be sold, transferred or moved, make sure the instruction manual accompanies the Washer-dryer to inform the new owner as to its operation and features. Read these instructions carefully: they contain vital information on installation, use and safety.
Levelling your appliance correctly will provide it with stability and avoid any vibrations, noise and shifting during operation. If it is placed on a fitted or loose carpet, adjust the feet in such a way as to allow enough room for ventilation beneath the Washerdryer.

Unpacking and levelling

Unpacking
Electric and water connections
Connecting the water inlet hose
1. Unpack the Washer-dryer. 2. Check whether the Washer-dryer has been damaged during transport. If this is the case, do not install it and contact your retailer. 3. Remove the four protective screws and the rubber washer with the respective spacer, situated on the rear of the appliance (see figure).
1. Insert seal A into the end of the inlet hose and screw the latter onto a cold water tap with a 3/4 gas threaded mouth (see figure). Before making the connection, allow the water to run freely until it is perfectly clear. 2. Connect the other end of the water inlet hose to the Washer-dryer, screwing it onto the appliance's cold water inlet, situated on the top right-hand side on the rear of the appliance (see figure).
4. Seal the gaps using the plastic plugs provided. 5. Keep all the parts: you will need them again if the Washer-dryer needs to be moved to another location.
Packaging materials are not children's toys.

Levelling

3. Make sure there are no kinks or bends in the hose.
The water pressure at the tap must be within the
values indicated in the Technical details table (on the next page).
1. Install the Washer-dryer on a flat sturdy floor, without resting it up against walls, furniture cabinets or other. 2. If the floor is not perfectly level, compensate for any unevenness by tightening or loosening the adjustable front feet (see figure); the angle of inclination, measured according to the worktop, must not exceed 2.

If the water inlet hose is not long enough, contact
a specialist store or an authorised serviceman.
Connecting the drain hose

65 - 100 cm

Connect the drain hose, without bending it, to a draining duct or a wall drain situated between 65 and 100 cm from the floor;
the supply voltage is included within the values i ndicated on the Technical details table (see page 5); the socket is compatible with the washing machine's plug. If this is not the case, replace the socket or the plug. Your appliance is now supplied with a 13 amp fused plug it can be plugged into a 13 amp socket for immediate use. Before using the appliance please read the instructions below.
The drain hose may be connected to an under-sink trap. Before connecting the drain hose from the machine ensure that any blanks or removable ends have been taken off the spigot. If it is place over the edge of a basin or sink be sure the free end of the hose should not be underwater.
WARNING - THIS APPLIANCE MUST BE EARTHED. THE FOLLOWING OPERATIONS SHOULD BE CARRIED OUT BY A QUALIFIED ELECTRICIAN. Replacing the fuse: When replacing a faulty fuse, a 13 amp ASTA approved fuse to BS 1362 should always be used, and the fuse cover re-fitted. If the fuse cover is lost, the plug must not be used until a replacement is obtained. Replacement fuse covers: If a replacement fuse cover is fitted, it must be of the correct colour as indicated by the coloured marking or the colour that is embossed in words on the base of the plug. Replacements can be obtained directly from your nearest Service Depot. Removing the plug: If your appliance has a non-rewireable moulded plug and you should wish to re-route the mains cable through partitions, units etc., please ensure that either: the plug is replaced by a fused 13 ampere rewearable plug bearing the BSI mark of approval. or: the mains cable is wired directly into a 13 amp cable outlet, controlled by a switch, (in compliance with BS 5733) which is accessible without moving the appliance. Disposing of the plug: Ensure that before disposing of the plug itself, you make the pins unusable so that it cannot be accidentally inserted into a socket. Instructions for connecting cable to an alternative plug: Important: the wires in the mains lead are coloured in accordance with the following code: Green & Yellow Earth Blue Neutral Brown Live
We advise against the use of hose extensions; in
case of absolute need, the extension must have the same diameter as the original hose and must not exceed 150 cm in length. Ensure that if the drain hose is pushed into a standpipe, that the end does not go down more than 15cms (6 inches). If the hose is pushed down too far, this may cause the machine to self -syphon ie. continuously empty as it is filling.

Electric connection

Before plugging the appliance into the mains socket, make sure that: the socket is earthed and in compliance with the applicable law; the socket is able to sustain the appliance's maximum power load indicated in the Technical details table (see page 5);
As the colours of the wires in the lead may not correspond with the coloured markings identifyng the terminals in your plug, proceed as follows: Connect Green & Yellow wire to terminal marked E or coloured Green or Green & Yellow. or Connect Brown wire to terminal marked L or coloured Red. Connect Blue wire to terminal marked N or coloured Black. If a 13 amp plug (BS 1363) is used it must be fitted with a 13 amp fuse, either in the plug or adaptor or at the distribution board. If you are in any doubt the electrical supply to your machine, consult a qualified electrician before use. How to connect an alternative plug: The wires in this mains lead are coloured in accordance with the following code: BLUE NEUTRAL (N) BROWN LIVE (L) GREEN & YELLOW EARTH (E) Disposing of the appliance: When disposing of the appliance please remove the plug by cutting the mains cable as close as possible to the plug body and dispose of it as described above.
Warning! The company denies all liability if and when these norms are not respected.

The first wash cycle

Once the appliance has been installed, and before you use it for the first time, run a wash cycle with detergent and no laundry, setting the 90C programme without a pre-wash cycle.

GREEN & YELLOW

13 ampere fuse

CROSS-BAR CORD GRIP

The washing machine should not be installed in an outdoor environment, not even when the area is sheltered, because it may be very dangerous to leave it exposed to rain and thunderstorms. When the washing machine is installed, the mains socket must be within easy reach. Do not use extensions or multiple sockets. The power supply cable must never be bent or dangerously compressed. The power supply cable must only be replaced by an authorised serviceman.

Technical details

Model WIDL 146 59.5 cm wide 85 cm high 53.5 cm deep from 1 to 5 kg for the wash programme; from 1 to 4 kg for the drying programme please refer to the technical data plate fixed to the machine maximum pressure 1 MPa (10 bar) minimum pressure 0.05 MPa (0.5 bar) drum capacity 46 litres up to 1400 rpm Wash: programme 2; temperature 60C; run with a load of 5 kg. Drying: first drying cycle performed with a 1 kg load, by selecting a drying time of 40 min; Second drying cycle performed with a 4 kg load and the DRYING knob on the setting. This appliance is compliant with the following European Community Directives: - 73/23/CEE of 19/02/73 (Low Voltage) and subsequent amendments - 89/336/CEE of 03/05/89 (Electromagnetic Compatibility) and subsequent amendments - 2002/96/CE
Dimensions Capacity Electric connections Water connections Spin speed
Control programmes according to EN 60456 directive

Washer-dryer description

Control panel

Buttons

FUNCTION ON-OFF/ DOOR ON-OFF LOCK Button

Detergent dispenser

PROGRAMME

Knob Button

START/RESET DRYING

TEMPERATURE

Detergent dispenser: to add detergent and fabric softener (see page 8). LEDS: to find out which wash cycle phase is under way. If the Delay Timer function has been set, the time left until the programme starts will be indicated (see page 5). DRYING knob: to set the desired drying cycle (see page 7). FUNCTION buttons: to select the functions available. The button corresponding to the function selected will remain on.
TEMPERATURE knob: to set the temperature or the cold wash cycle (see page 7). START/RESET button: to start the programmes or cancel any incorrect settings. ON-OFF/DOOR LOCK Led: to find out whether the Washer-dryer is on and if the appliance door can be opened (see page 5). ON/OFF button: to turn the Washer-dryer on and off. PROGRAMME knob: to select the wash programmes. The knob stays still during the cycle.
The LEDS provide important information. This is what they can tell you: Delay set: If the Delay Timer function has been enabled (see page. 7), once you have started the programme, the LED corresponding to the delay set will begin to flash:

Cycle phase under way: During the wash cycle, the LEDs gradually illuminate on to indicate the cycle phase under way: Prewash / Wash Rinse Spin cycle Drying Note: - during draining, the LED corresponding to the Spin cycle phase will be turned on. - when the drying cycle is complete, the indicator will flash, to indicate that light relative to phase the DRYING knob needs to be set back to the 0 setting. Function buttons The FUNCTION BUTTONS also act like LEDS. When a function is selected, the corresponding button is illuminated. If the function selected is incompatible with the programme set, the button will flash and the function will not be enabled. If you set a function that is incompatible with another function you selected previously, only the last one selected will be enabled.
As time passes, the remaining delay will be displayed, and the corresponding LED will flash:
Once the set delay is complete, the flashing LED will turn off and the programme set will start.
ON-OFF/DOOR LOCK led: If this LED is on, the appliance door is locked to prevent it from being opened accidentally; to avoid any damages, wait for the LED to flash before you open the appliance door.
The rapid flashing of the ON-OFF/DOOR LOCK Led together with the flashing of at least one other LED indicates there is an abnormality (see page 13).

Starting and Programmes

Briefly: starting a programme
1. Switch the Washer-dryer on by pressing button. All the LEDS will light up for a few seconds and the ON-OFF/DOOR LOCK Led will begin to flash. 2. Load your laundry into the washing machine and shut the appliance door. 3. Set the PROGRAMME knob to the programme required. 4. Set the wash temperature (see page 7). 5. Set the drying cycle if necessary (see page 7). 6. Add the detergent and any fabric softener (see page 8). 7. Start he programme by pressing the START/RESET button. To cancel it, keep the START/RESET button pressed for at least 2 seconds. 8. When the programme is finished, the ON-OFF/ DOOR LOCK Led will flash to indicate that the appliance door can be opened. Take out your laundry and leave the appliance door ajar to allow the drum to dry thoroughly. Turn the Washer-dryer. off by pressing button

D etergent prew ash w ash Cycle Fabric length D escrip tion of wash cycle softener (minutes)

Programme table

Type of fabric and degree of soil Program. Tem perature D rying C ycle

S tandard

C otton: Extremely soiled whites (sheets, tablecloths, etc.) C otton: Extremely soiled whites (sheets, tablecloths, etc.) C otton: Heavily soiled whites and fast colours C otton: Heavily soiled whites and delicate colours Cotton: Slightly soiled whites and delicate colours (shirts, jumpers, etc.) Synthetics: Heavily soiled fast colours (baby linen, etc.) Synthetics: Heavily soiled fast colours (baby linen, etc.) 8

90C 90C 60C 40C 40C

40C 40C 30C
W ool Very delicate fabrics (curtains, silk, viscose, etc.)
Drying cotton Drying delicates
Pre-wash, wash cycle, rinse cycles, intermediate and final spin cycles Wash cycle, rinse cycles, intermediate and final spin cycles Wash cycle, rinse cycles, intermediate and final spin cycles Wash cycle, rinse cycles, intermediate and final spin cycles Wash cycle, rinse cycles, intermediate and final spin cycles Wash cycle, rinse cycles, anti-crease or delicate spin cycle Wash cycle, rinse cycles, anti-crease or delicate spin cycle Wash cycle, rinse cycles anti-crease or delicate spin cycle Wash cycle, rinse cycles, anti-crease or draining cycle
Wash cycle, rinse cycles, intermediate and final spin cycles Wash cycle, rinse cycles, delicate spin cycle Wash cycle, rinse cycles and delicate spin cycle
Cold wash (without detergents), wash cycle, rinse cycles, and delicate spin cycle

Tim e 4 yo u

C otton: Heavily soiled whites and

fast colours

Synthetics: Delicate colours (all types of slightly soiled garments) Synthetics: Delicate colours (all types of slightly soiled garments)

S po rt

Sports shoes (MAX. 2 pairs) Fabrics for sportswear (Tracksuits, shorts, etc.) PAR TIAL PR OGR AM M ES Rinse Spin cycle Drain Rinse cycles and spin cycle Draining and spin cycle Drain
Wash cycle, rinse cycles, intermediate and final spin cycles
Notes -For programme 9, we advise against exceeding a wash load of 3.5 kg. -For programme 13 we advise against exceeding a wash load of 2 kg. -For the anti-crease function: see Easy iron, opposite page. The information contained in the table is purely indicative. Special programme Daily (programme 11 for Synthetics) is designed to wash lightly soiled garments in a short amount of time: it only lasts 30 minutes and allows you to save on both time and energy. By setting this programme (11 at 30C), you can wash different fabrics together (except for woollen and silk items), with a maximum load of 3 kg. We recommend the use of liquid detergent.

Personalisations

Turn the TEMPERATURE knob to set the wash temperature (see Programme table on page 6). The temperature can be lowered, or even set to a cold wash ( ). Turn the DRYING knob to set the desired drying type. Two options are available: A - Based on time: From 40 minutes to 150. B - Based on the damp level of the dry clothes: : slightly damp clothes, easy to iron. Iron : dry clothes to put away. Hanger : very dry clothes, recommended for towelling Cupboard and bathrobes. A cooling stage is foreseen at the end of the drying cycle.

Setting the temperature

The data contained in the table are purely indicative.

Set the drying cycle

Table of drying times
Fabric type Load type Max. load (kg)

Cupboard

Hanger
Cotton, Linen Cotton Terital, Cotton Acrylics
Clothing of different sizes
Terry towels Sheets, Shirts

Pyjamas, socks, etc.

Slips, tights, stockings, etc. If your laundry load to wash and dry is exceptionally in excess Nylon of the maximum load foreseen (see table opposite), perform the wash cycle, and when the programme is complete, divide up the garments and put part of them back in the drum. Now follow the instructions provided for a dry only cycle. Repeat this procedure for the remainder of the load.
Dry only Turn the PROGRAMME knob to one of the drying settings (7-8) depending on the type of fabric, then select the desired drying type using the DRYING knob. Important: - A spin cycle is carried out during the drying if you have set a cotton programme and a level of , Hanger , Iron ). dryness (Cupboard - For cotton loads of less than 1 Kg, use the drying programme designed for delicate fabrics.

Functions

To enable a function: 1. press the button corresponding to the desired function, according to the table below; 2. the function is enabled when the corresponding button is illuminated. Note: The rapid flashing of the button indicates that the corresponding function cannot be selected for the programme set.
Fu n c tion E ffe c t D elays t h e s t art o f t h e w as h by u p t o 9 h o u rs. T h is o p t io n redu ces t h e am o u n t o f creas in g o n fab rics , m akin g t h em eas ier t o iro n. I n creas es th e efficien cy o f t h e rin s e. R ed u ces t h e s p in s peed. C om m e n ts P res s th e bu t to n rep eat ed ly u n t il t h e L ED co rres p o n d in g t o th e d es ired delay is t u rn ed o n. T h e fift h t im e t h e b u t t o n is p res s ed , t h e fu n ct io n w ill be d is ab led. N.B.: O n ce yo u h ave p res s ed th e S t art /R es et b u t t o n , t h e d elay can o n ly b e d ecreas ed if yo u w is h t o m o d ify it. W h en t h is fu n ctio n is s et, p ro g ram m es 4 , 5 , 6 w ill en d w it h t h e lau n d ry left t o s o ak (A n t i-creas e) an d t h e R in s e cycle ph as e L ED w ill flas h. - t o co n clu d e t h e cycle, p res s t h e S TA R T /R ES ET b u t t o n ; - t o ru n t h e d rain in g cycle alo n e, s et t h e k n o b t o t h e relat ive s ym bo l an d p res s t h e S TA R T /R ES ET b u t t o n. R eco m m en d ed w h en th e app lian ce h as a fu ll lo ad o r w it h larg e q u an t it ies o f d et erg en t. E na b le d with p rogr a m m e s:

D elay T im er

Eas y iro n
3, 4, 5, 6, 9 , 1 0, R in se c yc le.

Ex t ra R in s e

1, 2, 3, 4, 9, 10, 12, 13, R in se c yc le. A ll p r ogr a m m e s e x c e p t for 6 a n d d r a in in g.

1400-600

Detergents and laundry
Good washing results also depend on the correct dose of detergent: adding too much detergent won't necessarily make for a more efficient wash, and may in fact cause build up on the interior of your appliance and even pollute the environment. Open up the detergent dispenser and pour in the detergent and fabric softener, as follows.

Special items

Curtains: fold curtains and place them in a pillow case or mesh bag. Wash them separately without exceeding half the appliance load. Use programme 6 which excludes the spin cycle automatically. Quilted coats and windbreakers: if they are padded with goose or duck down, they can be machine-washed. Turn the garments inside out and load a maximum of 2-3 kg, repeating the rinse cycle once or twice and using the delicate spin cycle. Wool: for best results, use a specific detergent, taking care not to exceed a load of 1 kg.
compartment 1: Detergent for pre-wash (powder) compartment 2: Detergent for the wash cycle (powder or liquid) Liquid detergent should only be poured in immediately prior to the wash cycle start. compartment 3: Additives (fabric softeners, etc.) The fabric softener should not overflow from the grid.
Do not use hand wash detergent because it may form too much foam.

Preparing your laundry

Divide your laundry according to: - the type of fabric/the symbol on the label. - the colours: separate coloured garments from whites. Empty all pockets and check for loose buttons. Do not exceed the weight limits stated below, which refer to the weight when dry: Sturdy fabrics: max 5 kg Synthetic fabrics: max 2.5 kg Delicate fabrics: max 2 kg Wool: max 1 kg
How much does your laundry weigh?
sheet 400-500 g pillow case 150-200 g tablecloth 400-500 g bathrobe 900-1200 g towel 150-250 g

Precautions and advice

The Washer-dryer was designed and built in compliance with the applicable international safety regulations. The following information is provided for your safety and should consequently be read carefully.

old household electrical appliances must not be disposed of in the normal unsorted municipal waste stream. Old appliances must be collected separately in order to optimise the recovery and recycling of the materials they contain and reduce the impact on human health and the environment. The crossed out "wheeled bin" symbol on the product reminds you of your obligation, that when you dispose of the appliance it must be separately collected. Consumers should contact their local authority or retailer for information concerning the correct disposal of their old appliance.

General safety

This appliance has been designed for nonprofessional, household use and its functions must not be changed. This washing machine should only be used by adults and in accordance with the instructions provided in this manual. Never touch the washing machine when barefoot or with wet or damp hands or feet. Do not pull on the power supply cable to unplug the appliance from the electricity socket. Pull the plug out yourself. Do not open the detergent dispenser while the appliance is in operation. Do not touch the drain water as it could reach very high temperatures. Never force the washing machine door: this could damage the safety lock mechanism designed to prevent any accidental openings. In the event of a malfunction, do not under any circumstances touch internal parts in order to attempt repairs. Always keep children well away from the appliance while in operation. The appliance door tends to get quite hot during the wash cycle. Should it have to be moved, proceed with the help of two or three people and handle it with the utmost care. Never try to do this alone, because the appliance is very heavy. Before loading your laundry into the washing machine, make sure the drum is empty. During the drying phase, the door tends to get quite hot. Do not use the appliance to dry clothes that have been washed with flammable solvents (e.g. trichlorethylene). Do not use the appliance to dry foam rubber or similar elastomers. Make sure that the water tap is turned on during the drying cycles. This washer-dryer can only be used to dry clothes which have been pre-washed in water.
Saving energy and respecting the environment
Environmentally-friendly technology If you only see a little water through your appliance door, this is because thanks to the latest Indesit technology, your washing machine only needs less than half the amount of water to get the best results: an objective reached to respect the environment. Saving on detergent, water, energy and time To avoid wasting resources, the Washer-dryer should be used with a full load. A full load instead of two half loads allows you to save up to 50% on energy. The pre-wash cycle is only necessary on extremely soiled garments. Avoiding it will save on detergent, time, water and between 5 and 15% energy. Treating stains with a stain remover or leaving them to soak before washing will cut down the need to wash them at high temperatures. A programme at 60C instead of 90C or one at 40C instead of 60C will save up to 50% on energy. Use the correct quantity of detergent depending on the water hardness, how soiled the garments are and the amount of laundry you have, to avoid wastage and to protect the environment: despite being biodegradable, detergents do contain ingredients that alter the natural balance of the environment. In addition, avoid using fabric softener as much as possible. If you use your washing machine from late in the afternoon until the early hours of the morning, you will help reduce the electricity board's peak load. The Delay Timer option (see page 7) helps to organise your wash cycles accordingly. If your laundry has to be dried in a tumble dryer, select a high spin speed. Having the least water possible in your laundry will save you time and energy in the drying process.

Disposal

Disposing of the packaging material:observe local regulations, so the packaging can be re-used. The European Directive 2002/96/EC on Waste Electrical and Electronic Equipment, requires that

Care and maintenance

Cutting off the water or electricity supply
Turn off the water tap after every wash. This will limit the wear of your appliance's water system and also prevent leaks. Unplug your appliance when cleaning it and during all maintenance operations.

Cleaning the pump

The Washer-dryer is fitted with a self-cleaning pump that does not require any maintenance. Sometimes, small items (such as coins or buttons) may fall into the pre-chamber that protects the pump, situated in the lower part of the same.
Make sure the wash cycle has ended and unplug the appliance.
To access the pre-chamber: 1. using a screwdriver, remove the cover panel on the lower front of the Washer-dryer (see figure);

Cleaning your appliance

The exterior and rubber parts of your appliance can be cleaned with a soft cloth soaked in lukewarm soapy water. Do not use solvents or abrasives.
Cleaning the detergent dispenser
Remove the dispenser by raising it and pulling it out (see figure). Wash it under running water; this operation should be repeated frequently.
2. unscrew the lid rotating it anticlockwise (see figure): a little water may trickle out. This is perfectly normal;
Caring for your appliance door and drum
Always leave the appliance door ajar to prevent unpleasant odours from forming. 3. clean the interior thoroughly; 4. screw the lid back on; 5. reposition the panel, making sure the hooks are securely in place before you push it onto the appliance.
Checking the water inlet hose
Check the water inlet hose at least once a year. If you see any cracks, replace it immediately: during the wash cycles, water pressure is very strong and a cracked hose could easily split open.
Never use hoses that have already been used.

Troubleshooting

Your Washer-dryer could fail to work. Before calling for Assistance (see page 12), make sure the problem can't easily be solved by consulting the following list.

Problem

The washer-dryer won't start.
Possible causes/Solution:
The appliance is not plugged into the socket, or not enough to make contact. There has been a power failure. The appliance door is not shut properly. button has not been pressed. The The START/RESET button has not been pressed. The water tap is not turned on. A delayed start has been set (using the Delay Timer, see page 7). The water inlet hose is not connected to the tap. The hose is bent. The water tap is not turned on. There is a water shortage. The water pressure is insufficient. The START/RESET button has not been pressed.
The wash cycle won't start.
The washer-dryer fails to load water.
The washer-dryer continuously loads and unloads water.
The drain hose is not fitted between 65 and 100 cm from the floor (see page 3). The free end of the hose is underwater (see page 3). The wall drainage system doesn't have a breather pipe. If the problem persists even after these checks, turn off the water tap, switch the appliance off and call for Assistance. If the dwelling is on one of the upper floors of a building, there may be drain trap problems causing the Washer-dryer to load and unload water continuously. In order to avoid such an inconvenience, special anti-drain trap valves are available in shops. The programme does not foresee the draining: some programmes require enabling the draining manually (see page 6). The Easy iron option is enabled: to complete the programme, press the START/RESET button (see page 7). The drain hose is bent (see page 3). The drain duct is clogged. The drum was not unblocked correctly during installation (see page 2). The Washer-dryer is not level (see page 2). The Washer-dryer is closed in between furniture cabinets and the wall (see page 2). The water inlet hose is not screwed on correctly (see page 2). The detergent dispenser is obstructed (to clean it, see page 10). The drain hose is not secured properly (see page 3). Call for Assistance because this means there is an abnormality.
The washer-dryer does not drain or spin.
The washer-dryer vibrates too much during the spin cycle.

The washer-dryer leaks.

The ON-OFF/DOOR LOCK Led flashes rapidly at the same time as at least one other LED. There is too much foam.
The detergent is not suitable for machine washing (it should bear the definition "for washing machines" or "hand and machine wash", or the like). You used too much detergent. The appliance is not plugged into the socket, or not enough to make contact. There has been a power failure. The appliance door is not shut properly. A delayed start has been set (using the Delay Timer, see page 7). the DRYING knob is on the 0 setting.

The washer-dryer does not dry.

Service

Before calling for Assistance: Check whether you can solve the problem on your own (see page 11); Restart the programme to check whether the problem has been solved; If this is not the case, contact an authorised Technical Service Centre on the telephone number provided on the guarantee certificate.
Always request the assistance of authorised servicemen.
Notify the operator of: the type of problem; the appliance model (Mod.); the serial number (S/N). This information can be found on the data plate situated on the rear of the washer-dryer.

195063145.00

03/2007 - Xerox Business Services

Instructions for use

WASHER-DRYER Contents

English,1

Installation, 2-3-4-5
Unpacking and levelling, 2 Electric and water connections, 2-3 The first wash cycle, 4 Technical details, 5
Washer-dryer description, 6-7

Control panel, 6 Leds, 7

Starting and Programmes, 8
Briefly: how to start a programme, 8 Programme table, 8

Personalisations, 9

WIDL 146
Setting the temperature, 9 Setting the drying cycle, 9 Functions, 9 Detergent dispenser, 10 Preparing your laundry, 10 Special items, 10
Detergents and laundry, 10
Precautions and advice, 11
General safety, 11 Disposal, 11 Saving energy and respecting the environment, 11

Care and maintenance, 12

Cutting off the water or electricity supply, 12 Cleaning your appliance, 12 Cleaning the detergent dispenser, 12 Caring for your appliance door and drum, 12 Cleaning the pump, 12 Checking the water inlet hose, 12
Troubleshooting, 13 Service and Guarantee, 14-15-16
Before calling for Assistance, 14 Guarantee. 15-16

Installation

Keep this instruction manual in a safe place for future reference. Should the appliance be sold, transferred or moved, make sure the instruction manual accompanies the washer-dryer to inform the new owner as to its operation and features. Read these instructions carefully: they contain vital information on installation, use and safety.
Levelling your appliance correctly will provide it with stability and avoid any vibrations, noise and shifting during operation. If it is placed on a fitted or loose carpet, adjust the feet in such a way as to allow enough room for ventilation beneath the washerdryer.

Unpacking and levelling

Unpacking
Electric and water connections
Connecting the water inlet hose
1. Unpack the washer-dryer. 2. Check whether the washer-dryer has been damaged during transport. If this is the case, do not install it and contact your retailer. 3. Remove the four protective screws and the rubber bush with the respective spacer, situated on the rear of the appliance (see also the installation leaflet). NB:The plastic spacers may fall down inside the machine once the bolt has been removed, and will not interfere with the operation of the machine. 4. Seal the gaps using the plastic plugs provided. 5. Keep all the parts: you will need them again if the washing machine needs to be moved to another location.
1. Insert seal A into the end of the inlet hose and screw the latter onto a cold water tap with a 3/4 gas threaded mouth (see figure). Before making the connection, allow the water to run freely until it is perfectly clear. 2. Connect the other end of the water inlet hose to the washer-dryer, screwing it onto the appliance's cold water inlet, situated on the top right-hand side on the rear of the appliance (see figure).
3. Make sure there are no kinks or bends in the hose.
Packaging materials are not children's toys.

Levelling

The water pressure at the tap must be within the
values indicated in the Technical details table (on the next page).
Your machine may make a considerable amount of noise if the two front feet have not been adjusted correctly. 1. Install the washer-dryer on a flat sturdy floor, without resting it up against walls, furniture cabinets or other. 2. If the floor is not perfectly level, compensate for any unevenness by tightening or loosening the adjustable front feet (see figure); the angle of inclination, measured according to the worktop, must not exceed 2.
If the water inlet hose is not long enough, contact
a specialist store or an authorised serviceman.
Ensure that the supply taps are allowing water
through. Old taps may seize in the closed position and thus prevent water reaching the machine.
Connecting the drain hose

65 - 100 cm

Connect the drain hose, without bending it, to a draining duct or a wall drain situated between 65 and 100 cm from the floor;
the supply voltage is included within the values indicated on the Technical details table (see page 5); the socket is compatible with the washer-dryer's plug. If this is not the case, replace the socket or the plug. Your appliance is now supplied with a 13 amp fused plug it can be plugged into a 13 amp socket for immediate use. Before using the appliance please read the instructions below.

Installation Description

Where it connects to the waste water pipe cut end off spigot or remove the blanking cap
The drain hose may be connected to an under-sink trap. Before connecting the drain hose from the machine ensure that any blanks or removable ends have been taken off the spigot. If it is place over the edge of a basin or sink be sure the free end of the hose should not be underwater.
WARNING - THIS APPLIANCE MUST BE EARTHED. THE FOLLOWING OPERATIONS SHOULD BE CARRIED OUT BY A QUALIFIED ELECTRICIAN. Replacing the fuse: When replacing a faulty fuse, a 13 amp ASTA approved fuse to BS 1362 should always be used, and the fuse cover re-fitted. If the fuse cover is lost, the plug must not be used until a replacement is obtained. Replacement fuse covers: If a replacement fuse cover is fitted, it must be of the correct colour as indicated by the coloured marking or the colour that is embossed in words on the base of the plug. Replacements can be obtained directly from your nearest Service Depot. Removing the plug: If your appliance has a non-rewireable moulded plug and you should wish to re-route the mains cable through partitions, units etc., please ensure that either: the plug is replaced by a fused 13 ampere rewearable plug bearing the BSI mark of approval. or: the mains cable is wired directly into a 13 amp cable outlet, controlled by a switch, (in compliance with BS 5733) which is accessible without moving the appliance. Disposing of the plug: Ensure that before disposing of the plug itself, you make the pins unusable so that it cannot be accidentally inserted into a socket. Instructions for connecting cable to an alternative plug: Important: the wires in the mains lead are coloured in accordance with the following code: Green & Yellow Earth Blue Neutral Brown Live
Programmes Detergents Precautions
We advise against the use of hose extensions; in
case of absolute need, the extension must have the same diameter as the original hose and must not exceed 150 cm in length. Ensure that if the drain hose is pushed into a standpipe, that the end does not go down more than 15cms (6 inches). If the hose is pushed down too far, this may cause the machine to self -syphon ie. continuously empty as it is filling.

Care Troubleshooting

Electric connection
Before plugging the appliance into the mains socket, make sure that: the socket is earthed and in compliance with the applicable law; the socket is able to sustain the appliance's maximum power load indicated in the Technical details table (see page 5);

Service

As the colours of the wires in the lead may not correspond with the coloured markings identifyng the terminals in your plug, proceed as follows: Connect Green & Yellow wire to terminal marked E or coloured Green or Green & Yellow. or Connect Brown wire to terminal marked L or coloured Red. Connect Blue wire to terminal marked N or coloured Black. If a 13 amp plug (BS 1363) is used it must be fitted with a 13 amp fuse, either in the plug or adaptor or at the distribution board. If you are in any doubt the electrical supply to your machine, consult a qualified electrician before use. How to connect an alternative plug: The wires in this mains lead are coloured in accordance with the following code: BLUE NEUTRAL (N) BROWN LIVE (L) GREEN & YELLOW EARTH (E) Disposing of the appliance: When disposing of the appliance please remove the plug by cutting the mains cable as close as possible to the plug body and dispose of it as described above.
Warning! The company denies all liability if and when these norms are not respected.

The first wash cycle

Once the appliance has been installed, and before you use it for the first time, run a wash cycle with detergent and no laundry, setting the 90C programme without a pre-wash cycle.

GREEN & YELLOW

13 ampere fuse

CROSS-BAR CORD GRIP

The washing machine should not be installed in an outdoor environment, not even when the area is sheltered, because it may be very dangerous to leave it exposed to rain and thunderstorms. When the washing machine is installed, the mains socket must be within easy reach. Do not use extensions or multiple sockets. The power supply cable must never be bent or dangerously compressed. The power supply cable must only be replaced by an authorised serviceman.

Technical details

Model WIDL 146 59.5 cm wide 85 cm high 53.5 cm deep from 1 to 5 kg for the wash programme; from 1 to 4 kg for the drying programme please refer to the technical data plate fixed to the machine maximum pressure 1 MPa (10 bar) minimum pressure 0.05 MPa (0.5 bar) drum capacity 46 litres up to 1400 rpm Wash: programme 2; temperature 60C; run with a load of 5 kg. Drying: first drying cycle performed with a 1 kg load, by selecting a drying time of 40 min; Second drying cycle performed with a 4 kg load and the DRYING knob on the setting. This appliance is compliant with the following European Community Directives: - 73/23/CEE of 19/02/73 (Low Voltage) and subsequent amendments - 89/336/CEE of 03/05/89 (Electromagnetic Compatibility) and subsequent amendments - 2002/96/CE

Precautions Care Troubleshooting
ON-OFF/DOOR LOCK led: If this LED is on, the appliance door is locked to prevent it from being opened accidentally; to avoid any damages, wait for the LED to flash before you open the appliance door.
The rapid flashing of the ON-OFF/DOOR LOCK Led together with the flashing of at least one other LED indicates there is an abnormality. Call for Technical Assistance (see page 13).

Starting and Programmes

Briefly: starting a programme
1. Switch the Washer-dryer on by pressing button. All the LEDS will light up for a few seconds and the ON-OFF/DOOR LOCK Led will begin to flash. 2. Load your laundry into the washing machine and shut the appliance door. 3. Set the PROGRAMME knob to the programme required. 4. Set the wash temperature (see page 9). 5. Set the drying cycle if necessary (see page 9). 6. Add the detergent and any fabric softener (see page 10). 7. Start the programme by pressing the START/RESET button for one second. Once the programme has been accepted all of the option and status LED's will illuminate momentarily, the Door Lock LED will be lit and the relevant wash cycle progress LED will also be lit. To cancel it, keep the START/RESET button pressed for at least 2 seconds. 8. When the programme is finished, the ON-OFF/ DOOR LOCK Led will flash to indicate that the appliance door can be opened. Take out your laundry and leave the appliance door ajar to allow the drum to dry thoroughly. Turn the Washer-dryer. off by pressing button
M ax. C ycle Fabric Sp in length softener Sp eed s (m inutes) (r.p.m.) D e scrip tion of wash cyc le

Programme table

Typ e of fab ric and d egre e of soil P rog. Tem p e - D rying rature C ycle D e tergent prew as h w as h

S tandard

C otton: Extremely s oiled w h ites (s h eets, tablecloth s, etc.) C otton: Extremely s oiled w h ites (s h eets, tablecloth s, etc.) C otton: Heavily soiled w h ites an d fast colou rs C otton: Heavily soiled w h ites an d delicate colou rs Cotton: Slightly soiled whites and delicate colours (shirts, jumpers, etc.) Synthe tic s: Heavily soiled fast colou rs (baby lin en , etc.) Synthe tic s: Heavily soiled fast colou rs (baby lin en , etc.) W ool Very delicate fabrics (cu rtain s, silk, vis cos e, etc.)
D rying cotton D rying delicates 8

90C 90C 60C 40C 40C

Max. Max. Max. Max. Max. 600 no Max. no

40C 40C 3 0C

Pre-w as h , w as h cycle, rin s e cycles, in termediate an d fin al s pin cycles Wash cycle, rin s e cycles , in termediate an d fin al s pin cycles Wash cycle, rin s e cycles , in termediate an d fin al s pin cycles Wash cycle, rin s e cycles , in termediate an d fin al s pin cycles Wash cycle, rin s e cycles , in termediate an d fin al s pin cycles Wash cycle, rin s e cycles , anti-creas e or delicate s pin cycle Wash cycle, rin s e cycles , anti-creas e or delicate s pin cycle Wash cycle, rin s e cycles anti-creas e or delicate s pin cycle Wash cycle, rin s e cycles , anti-creas e or drain in g cycle

Tim e 4 y o u

C otton: Heavily soiled w h ites an d fast colou rs Synthe tic s: Delicate colours (all types of slightly soiled garments) Synthe tic s: Delicate colours (all types of slightly soiled garments)

Max. 800 800

Wash cycle, rin s e cycles , in termediate an d fin al s pin cycles Wash cycle, rin s e cycles , delicate s pin cycle Wash cycle, rin s e cycles and delicate s pin cycle
Cold wash (without detergents), wash cycle, rinse cycles, and delicate spin cycle

S port

Sports sh oes (MAX. 2 pairs) F abrics for sports w ear (Tracks u its, s h orts , etc.) PAR TIAL PR OGR AM M ES R in s e Spin cycle D rain

no 30 C

800 600
Wash cycle, rin s e cycles , in termediate an d fin al s pin cycles R in s e cycles and spin cycle D rainin g an d s pin cycle D rain
Notes -For programme 9, we advise against exceeding a wash load of 3.5 kg. -For programme 13 we advise against exceeding a wash load of 2 kg. -For the anti-crease function: see Easy iron, opposite page. The information contained in the table is purely indicative. Special programme Daily (programme 11 for Synthetics) is designed to wash lightly soiled garments in a short amount of time: it only lasts 30 minutes and allows you to save on both time and energy. By setting this programme (11 at 30C), you can wash different fabrics together (except for woollen and silk items), with a maximum load of 3 kg. We recommend the use of liquid detergent.

Personalisations

Turn the TEMPERATURE knob to set the wash temperature (see Programme table on page 8). The temperature can be lowered, or even set to a cold wash ( ). Turn the DRYING knob to set the desired drying type. Two options are available: A - Based on time: From 40 minutes to 150. B - Based on the damp level of the dry clothes: : slightly damp clothes, easy to iron. Iron : dry clothes to put away. Hanger : very dry clothes, recommended for towelling Cupboard and bathrobes. A cooling stage is foreseen at the end of the drying cycle.

Setting the temperature

The data contained in the table are purely indicative.

Set the drying cycle

Table of drying times
Fabric type Load type Max. load (kg)

Cupboard

Hanger
Cotton, Linen Cotton Terital, Cotton Acrylics
Clothing of different sizes
Terry towels Sheets, Shirts

Description

Precautions

D elay T im er
3, 4, 5, 6, 9 , 1 0, R in se c yc le.

Troubleshooting

Eas y iro n

Ex t ra R in s e

1, 2, 3, 4, 9, 10, 12, 13, R in se c yc le. A ll p r ogr a m m e s e x c e p t for 6 a n d d r a in in g.

1400-600

The machine has an intelligent built in check for out of balance loads. To let protect your machine it may reduce the
final spin speed if an unbalanced load is detected.
The balancing attempts may extend the total duration of the cycle, up to a maximum of 10 minutes.

Detergents and laundry

Good washing results also depend on the correct dose of detergent: adding too much detergent won't necessarily make for a more efficient wash, and may in fact cause build up on the interior of your appliance and even pollute the environment. Open up the detergent dispenser and pour in the detergent and fabric softener, as follows.

Special items

Curtains: fold curtains and place them in a pillow case or mesh bag. Wash them separately without exceeding half the appliance load. Use programme 6 which excludes the spin cycle automatically. Quilted coats and windbreakers: if they are padded with goose or duck down, they can be machine-washed. Turn the garments inside out and load a maximum of 2-3 kg, repeating the rinse cycle once or twice and using the delicate spin cycle. Wool: for best results, use a specific detergent, taking care not to exceed a load of 1 kg.
compartment 1: Detergent for pre-wash (powder) compartment 2: Detergent for the wash cycle (powder or liquid) Liquid detergent should only be poured in immediately prior to the wash cycle start. compartment 3: Additives (fabric softeners, etc.) The fabric softener should not overflow from the grid.
Do not use hand wash detergent because it may form too much foam.

Preparing your laundry

Divide your laundry according to: - the type of fabric/the symbol on the label. - the colours: separate coloured garments from whites. Empty all pockets and check for loose buttons. Do not exceed the weight limits stated below, which refer to the weight when dry: Sturdy fabrics: max 5 kg Synthetic fabrics: max 2.5 kg Delicate fabrics: max 2 kg Wool: max 1 kg

How much does your laundry weigh?
sheet 400-500 g pillow case 150-200 g tablecloth 400-500 g bathrobe 900-1,200 g towel 150-250 g

Precautions and advice

The Washer-dryer was designed and built in compliance with the applicable international safety regulations. The following information is provided for your safety and should consequently be read carefully.
disposed of in the normal unsorted municipal waste stream. Old appliances must be collected separately in order to optimise the recovery and recycling of the materials they contain and reduce the impact on human health and the environment. The crossed out "wheeled bin" symbol on the product reminds you of your obligation, that when you dispose of the appliance it must be separately collected. Consumers should contact their local authority or retailer for information concerning the correct disposal of their old appliance.

General safety

This appliance has been designed for nonprofessional, household use and its functions must not be changed. This washing machine should only be used by adults and in accordance with the instructions provided in this manual. Never touch the washing machine when barefoot or with wet or damp hands or feet. Do not pull on the power supply cable to unplug the appliance from the electricity socket. Pull the plug out yourself. Do not open the detergent dispenser while the appliance is in operation. Do not touch the drain water as it could reach very high temperatures. Never force the washing machine door: this could damage the safety lock mechanism designed to prevent any accidental openings. In the event of a malfunction, do not under any circumstances touch internal parts in order to attempt repairs. Always keep children well away from the appliance while in operation. The appliance door tends to get quite hot during the wash cycle. Should it have to be moved, proceed with the help of two or three people and handle it with the utmost care. Never try to do this alone, because the appliance is very heavy. Before loading your laundry into the washing machine, make sure the drum is empty. During the drying phase, the door tends to get quite hot. Do not use the appliance to dry clothes that have been washed with flammable solvents (e.g. trichlorethylene). Do not use the appliance to dry foam rubber or similar elastomers. Make sure that the water tap is turned on during the drying cycles. This washer-dryer can only be used to dry clothes which have been pre-washed in water.

Care and maintenance

Cutting off the water or electricity supply
Turn off the water tap after every wash. This will limit the wear of your appliance's water system and also prevent leaks. Unplug your appliance when cleaning it and during all maintenance operations.

Cleaning the pump

The Washer-dryer is fitted with a self-cleaning pump that does not require any maintenance. Sometimes, small items (such as coins or buttons) may fall into the pre-chamber that protects the pump, situated in the lower part of the same.
Make sure the wash cycle has ended and unplug the appliance.
To access the pre-chamber: 1. using a screwdriver, remove the cover panel on the lower front of the Washer-dryer (see figure);

Cleaning your appliance

The exterior and rubber parts of your appliance can be cleaned with a soft cloth soaked in lukewarm soapy water. Do not use solvents or abrasives.
Cleaning the detergent dispenser
Remove the dispenser by raising it and pulling it out (see figure). Wash it under running water; this operation should be repeated frequently.
2. unscrew the lid rotating it anticlockwise (see figure): a little water may trickle out. This is perfectly normal;
Caring for your appliance door and drum
Always leave the appliance door ajar to prevent unpleasant odours from forming. 3. clean the interior thoroughly; 4. screw the lid back on; 5. reposition the panel, making sure the hooks are securely in place before you push it onto the appliance.
Checking the water inlet hose
Check the water inlet hose at least once a year. If you see any cracks, replace it immediately: during the wash cycles, water pressure is very strong and a cracked hose could easily split open.
Never use hoses that have already been used.
Your washer-dryer could fail to work. Before calling for Assistance (see page 14), make sure the problem can't easily be solved by consulting the following list.

Problem

The washer-dryer won't start.

Possible causes/Solution:
The appliance is not plugged into the socket, or not enough to make contact. There has been a power failure. The appliance door is not shut properly. button has not been pressed. The The START/RESET button has not been pressed. NB: It should be held minimum one second. The water tap is not turned on. A delayed start has been set (using the Delay Timer, see page 9). The water inlet hose is not connected to the tap. The hose is bent. The water tap is not turned on. There is a water shortage. The water pressure is insufficient. The START/RESET button has not been pressed.
The washer-dryer does not fill with water.

Programmes

The machine continuously fills and empties with water. The washer-dryer does not drain or spin.
The drain hose is too low or too far in to the stand pipe (see page 3) for correct installation. The wall drainage system doesn't have a standard pipe (min. 38 mm). Some programs have a slower final spin to taked best care of the fabrics. See page 8 for details of the final spin speed for each program. The programme does not foresee the draining: some programmes require enabling the draining manually (see page 8). The Easy iron option is enabled: to complete the programme, press the START/RESET button (see page 9). The drain hose is bent (see page 3). Remove the drain hose from the standpipe or under-sink trap and check for blockages, ensuring that the water can drain freely away from the machine. When the machine is installed, the locking screws for the oscillating assembly are still in place. Remove the screws (see page 2). The washer-dryer is not level (see page 2). The washer-dryer is closed in between furniture cabinets and the wall (see page 2). The water inlet hose is not screwed on correctly (see page 2). The detergent dispenser is obstructed (to clean it, see page 12). The drain hose is not secured properly (see page 3). This means there is a problem with the machine. Before calling Assistance, please follow the set of instructions below: 1. Switch off the machine; 2. Remove the plug connecting the appliance to the mains supply and wait for at least 40 seconds; 3. Place the plug back into the socket; 4. Switch on the machine; 5. If the problem is still evident after this process has been carried out, contact Assistance. The detergent is not suitable for machine washing (it should bear the definition "for washing machines" or "hand and machine wash", or the like). You used too much detergent. The appliance is not plugged into the socket, or not enough to make contact. There has been a power failure. The appliance door is not shut properly. A delayed start has been set (using the Delay Timer, see page 9). the DRYING knob is on the 0 setting.

Detergents Precautions

The washer-dryer vibrates too much during the spin cycle.

The washer-dryer leaks.

The ON-OFF/DOOR LOCK Led flashes rapidly at the same time as at least one other LED.

There is too much foam.

The washer-dryer does not dry.
Before calling for Assistance: Check whether you can solve the problem on your own (see page 13); Restart the programme to check whether the problem has been solved; If this is not the case, contact an authorised Technical Service Centre on the telephone number provided on the guarantee certificate.
If the machine has been installed or used incorrectly, you may be charged for the maintenance callout service. Always request the assistance of authorised servicemen.
Notify the operator of: the type of problem; the appliance model (Mod.); the serial number (S/N). This information can be found on the data plate situated on the rear of the washer-dryer.

Guarantee

12 Months Parts and Labour Guarantee Your appliance has the benefit of our manufacturers guarantee, which covers the cost of breakdown repairs for twelve months from the date of purchase. This gives you the reassurance that if, within that time, your appliance is proven to be defective because of either workmanship or materials, we will, at our discretion, either repair or replace the appliance at no cost to you. This guarantee is subject to the following conditions: The appliance has been installed and operated correctly and in accordance with our operating and maintenance instructions. The appliance is used only on the electricity or gas supply printed on the rating plate. The appliance has been used for normal domestic purposes only. The appliance has not been altered, serviced, maintained, dismantled, or otherwise interfered with by any person not authorised by us. Any repair work must be undertaken by us or our appointed agent. Any parts removed during repair work or any appliance that is replaced become our property. The appliance is used in the United Kingdom or Republic of Ireland.

The guarantee does not cover: Damage resulting from transportation, improper use, neglect or interference or as a result of improper installation. Replacement of any consumable item or accessory. These include but are not limited to: plugs, cables, batteries, light bulbs, fluorescent tubes and starters, covers and filters. Replacement of any removable parts made of glass or plastic.
THIS GUARANTEE WILL NOT APPLY IF THE APPLIANCE HAS BEEN USED IN COMMERCIAL OR NON-DOMESTIC PREMISES. Extended Guarantees We offer a selection of repair protection plans that enable you to fully cover yourself against the expense of repair bills for the life of your policy. To find the ideal plan for you please call our advice line on 088 (ROI 0233). Free Helpdesk Service We have a dedicated team who can provide free advice and assistance with your appliance if you experience any technical difficulties within the first 90 days of ownership. Simply call our Indesit Service Hotline on 066 (ROI 413)for telephone assistance, or, where necessary, to arrange for an engineer to call.
Precautions Care Troubleshooting Service

195042972.04

11/2006 - Xerox Business Services

After Sales Service

No one is better placed to care for your Indesit appliance during the course of its working life than us - the manufacturer.
Essential Contact Information
Indesit Service We are the largest service team in Europe offering you access to 400 skilled telephone advisors and 1100 fully qualified engineers on call to ensure you receive fast, reliable, local service. UK: 066 Republic of Ireland: 413 www.indesitservice.co.uk Please note: Our advisors will require the following information: Model number: Serial number: Parts and Accessories We supply a full range of genuine replacement parts as well as accessory products that protect and hygienically clean your appliance to keep it looking good and functioning efficiently throughout its life. UK: 077 Republic of Ireland: 413 www.indesitservice.co.uk Indesit Company UK Ltd. Morley Way, Peterborough, PE2 9JB Indesit Company Unit 49 Airways Industrial Estate, Dublin 17

Recycling & Disposal Information
As part of Indesit's continued commitment to helping the environment, Indesit reserves the right to use quality, recycled components to keep down customer costs and minimise material wastage. Please dispose of packaging and old appliances carefully. To minimise the risk of injury to children, remove the door, plug and cut the mains cable off flush with the appliance. Dispose of these parts separately to ensure that the appliance can no longer be plugged into a mains socket, and the door cannot be locked shut.