Indesit Wisl 105
Here you can find all about Indesit Wisl 105 like manual and other informations. For example: review.
Indesit Wisl 105 manual (user guide) is ready to download for free.
On the bottom of page users can write a review. If you own a Indesit Wisl 105 please write about it to help other people. [ Report abuse or wrong photo | Share your Indesit Wisl 105 photo ]
Indesit Wisl 105, size: 4.2 MB
Indesit Wisl 105
indesit wisl 105 start!!!
User reviews and opinions
No opinions have been provided. Be the first and add a new opinion/review.
Unpacking and levelling, 14 Electric and water connections, 14-15 The first wash cycle, 15 Technical details, 15
Washing machine description, 16-17
Control panel, 16 Leds, 17
Starting and Programmes, 18
Briefly: how to start a programme, 18 Programme table, 18
Setting the temperature, 19 Setting the spin speed, 19 Functions, 19 Detergent dispenser, 20 Bleach cycle, 20 Preparing your laundry, 20 Special items, 20
Detergents and laundry, 20
Precautions and advice, 21
General safety, 21 Disposal, 21 Saving energy and respecting the environment, 21
Care and maintenance, 22
Cutting off the water or electricity supply, 22 Cleaning your appliance, 22 Cleaning the detergent dispenser, 22 Caring for your appliance door and drum, 22 Cleaning the pump, 22 Checking the water inlet hose, 22
Troubleshooting, 23 Service, 24
Before calling for Assistance, 24
Keep this instruction manual in a safe place for future reference. Should the appliance be sold, transferred or moved, make sure the instruction manual accompanies the washing machine to inform the new owner as to its operation and features. Read these instructions carefully: they contain vital information on installation, use and safety.
Levelling your appliance correctly will provide it with stability and avoid any vibrations, noise and shifting during operation. If it is placed on a fitted or loose carpet, adjust the feet in such a way as to allow enough room for ventilation beneath the washing machine.
Unpacking and levelling
Electric and water connections
Connecting the water inlet hose
1. Unpack the washing machine. 2. Check whether the washing machine has been damaged during transport. If this is the case, do not install it and contact your retailer. 3. Remove the 3 protective screws and the rubber washer with the respective spacer, situated on the rear of the appliance (see figure).
1. Insert seal A into the end of the inlet hose and screw the latter onto a cold water tap with a 3/4 gas threaded mouth (see figure). Before making the connection, allow the water to run freely until it is perfectly clear. 2. Connect the other end of the water inlet hose to the washing machine, screwing it onto the appliance's cold water inlet, situated on the top right-hand side on the rear of the appliance (see figure).
4. Seal the gaps using the plastic plugs provided. 5. Use the plug provided to seal the three holes where the plug was housed, situated on the lower right-hand side on the rear of your appliance. 6. Keep all the parts: you will need them again if the washing machine needs to be moved to another location.
3. Make sure there are no kinks or bends in the hose.
Packaging materials are not children's toys.
The water pressure at the tap must be within the
values indicated in the Technical details table (on the next page).
1. Install the washing machine on a flat sturdy floor, without resting it up against walls, furniture cabinets or other. 2. If the floor is not perfectly level, compensate for any unevenness by tightening or loosening the adjustable front feet (see figure); the angle of inclination, measured according to the worktop, must not exceed 2.
If the water inlet hose is not long enough, contact
a specialist store or an authorised serviceman.
Connecting the drain hose
Do not use extensions or multiple sockets.
Connect the drain hose, without bending it, to a draining duct or a wall drain situated between 65 and 100 cm from the floor;
The power supply cable must never be bent or dangerously compressed. The power supply cable must only be replaced by an authorised serviceman.
Warning! The company denies all liability if and when these norms are not respected.
The first wash cycle
alternatively, place it over the edge of a basin, sink or tub, fastening the duct supplied to the tap (see figure). The free end of the hose should not be underwater. Once the appliance has been installed, and before you use it for the first time, run a wash cycle with detergent and no laundry, setting the 90C programme without a pre-wash cycle.
We advise against the use of hose extensions; in case of absolute need, the extension must have the same diameter as the original hose and must not exceed 150 cm in length.
M odel W IL 1 05
Before plugging the appliance into the mains socket, make sure that: the socket is earthed and in compliance with the applicable law; the socket is able to sustain the appliance's maximum power load indicated in the Technical details table (on the right); the supply voltage is included within the values i ndicated on the Technical details table (on the right); the socket is compatible with the washing machine's plug. If this is not the case, replace the socket or the plug.
Dim ensions Capacity Electric connections Water connections Spin speed Control program m es according to IEC456 directive
5 9.5 cm w ide cm h ig h 5 3.5 cm deep from 1 to 5 kg vo ltage /0 Volts Hz max imu m abs o rbed pow er 0 W maximu m pres s u re 1 MPa (bar) min imu m pres s u re 0.M Pa (0.5 bar) dru m capacity 46 litres u p to 0 rpm
pro g ramme 2 ; temperatu re 6 0C; ru n w ith a lo ad o f 5 kg.
The washing machine should not be installed in an outdoor environment, not even when the area is sheltered, because it may be very dangerous to leave it exposed to rain and thunderstorms. When the washing machine is installed, the mains socket must be within easy reach.
T h is applian ce is co mplian t w ith th e follo w in g Eu ro pean Comm u n ity D irectives : - 7 3/2 3/CEE o f 19 /0 2/(L ow Vo ltage) an d s u bs equ en t am en dmen ts - 8 9//CEE o f /05 /89 (Electromagn etic Co mpatibility) an d s u bs equ en t amen dmen ts - 2/CE
Washing machine description
FUNCTION ON-OFF/ DOOR ON-OFF LOCK Button
START/RESET TEMPERATURE SPIN SPEED
Detergent dispenser: to add detergent and fabric softener (see page 20). LEDS: to find out which wash cycle phase is under way. If the Delay Timer function has been set, the time left until the programme starts will be indicated (see page 17). SPIN SPEED knob: to set the spin speed or exclude the spin cycle completely (see page 19). FUNCTION buttons: to select the functions available. The button corresponding to the function selected will remain on.
TEMPERATURE knob: to set the temperature or the cold wash cycle (see page 19). START/RESET button: to start the programmes or cancel any incorrect settings. ON-OFF/DOOR LOCK Led: to find out whether the washing machine is on and if the appliance door can be opened (see page 17). ON/OFF button: to turn the washing machine on and off. PROGRAMME knob: to select the wash programmes. The knob stays still during the cycle.
The LEDS provide important information. This is what they can tell you: Delay set: If the Delay Timer function has been enabled (see page. 19), once you have started the programme, the LED corresponding to the delay set will begin to flash: Cycle phase under way: During the wash cycle, the LEDs gradually illuminate on to indicate the cycle phase under way: Prewash Wash Rinse Spin cycle Note: during draining, the LED corresponding to the Spin cycle phase will be turned on. As time passes, the remaining delay will be displayed, and the corresponding LED will flash: Function buttons The FUNCTION BUTTONS also act like LEDS. When a function is selected, the corresponding button is illuminated. If the function selected is incompatible with the programme set, the button will flash and the function will not be enabled. If you set a function that is incompatible with another function you selected previously, only the last one selected will be enabled.
Installation Description Programmes Detergents
Once the set delay is complete, the flashing LED will turn off and the programme set will start.
Precautions Care Troubleshooting
ON-OFF/DOOR LOCK led: If this LED is on, the appliance door is locked to prevent it from being opened accidentally; to avoid any damages, wait for the LED to flash before you open the appliance door.
The rapid flashing of the ON-OFF/DOOR LOCK Led together with the flashing of at least one other LED indicates there is an abnormality. Call for Technical Assistance.
Starting and Programmes
Briefly: starting a programme
1. Switch the washing machine on by pressing button. All the LEDS will light up for a few seconds and the ON-OFF/DOOR LOCK Led will begin to flash. 2. Load your laundry into the washing machine and shut the appliance door. 3. Set the PROGRAMME knob to the programme required. 4. Set the wash temperature (see page 19). 5. Set the spin speed (see page 19). 6. Add the detergent and any fabric softener (see page 20). 7. Start he programme by pressing the START/RESET button. To cancel it, keep the START/RESET button pressed for at least 2 seconds. 8. When the programme is finished, the ON-OFF/ DOOR LOCK Led will flash to indicate that the appliance door can be opened. Take out your laundry and leave the appliance door ajar to allow the drum to dry thoroughly. Turn the washing. machine off by pressing button
Fab ric softener C ycle Sta in re m ova l length op tion /b le a c h (m inute s)
Typ e of fa b ric a nd d e gre e of soil P rogra m m e s Te m p e ra ture D e te rge nt prew as h w as h
D e sc rip tion of w a sh c yc le
Extremely soiled w h ites (sh eets, tablecloth s, etc.) Extremely soiled w h ites (sh eets, tablecloth s, etc.) Heavily soiled w h ites and fast colours Heavily soiled w h ites and delicate colours Sligh tly s oiled w h ites an d delicate colou rs (sh irts, ju mpers, etc.) Heavily soiled fast colours (baby linen, etc.) Heavily soiled fast colours (baby linen, etc.) Delicate colours (all types of sligh tly soiled garments) W oo l Very delicate fabrics (cu rtain s , s ilk, vis cos e, etc.)
9 0C 9 0C 6 0C 4 0C 4 0C 6 0C 4 0C 4 0C 4 0C 3 0C
D elicate/ Tradition al D elicate/ Tradition al D elicate/ Tradition al D elicate/ Tradition al D elicate D elicate D elicate
Pre-wash, wash cycle, rinse cycles, intermediate and final spin cycles Wash cycle, rinse cycles, intermediate and final spin cycles Wash cycle, rinse cycles, intermediate and final spin cycles Wash cycle, rinse cycles, intermediate and final spin cycles Wash cycle, rinse cycles, intermediate and final spin cycles Was h cycle, rin se cycles , an ticrease or delicate spin cycle Was h cycle, rin se cycles , an ticrease or delicate spin cycle Was h cycle, rin se cycles , an ticrease or delicate spin cycle W as h cycle, rin s e cycles , an ticreas e an d delicate s p in cycle W as h cycle, rin s e cycles , an ticreas e o r drain in g cycle Wash cycle, rinse cycles, intermediate and final spin cycles Wash cycle, rinse cycles, intermediate and final spin cycles Was h cycle, rin se cycles , delicate s pin cycle W as h cycle, rin s e cycles an d delicate s p in cycle
Cold w ash (w ithout detergents), w ash cycle, rin se cycles, and delicate spin cycle
Tim e 4 y o u
Heavily soiled w h ites and fast colours Sligh tly s oiled w h ites an d delicate colou rs (sh irts, ju mpers, etc.) Delicate colours (all types of sligh tly soiled garments) Delicate colours (all types of sligh tly soiled garments)
6 0C 4 0C
S po rts
Sports shoes (MAX. 2 pairs) Fabrics for sportsw ear (Tracksuits, sh orts, etc.) PAR TIAL P R OGR AM M E S R in s e Spin cycle D rain D elicate/ Tradition al R in s e cycles an d s pin cycle Draining and spin cycle D rain in g
Wash cycle, rinse cycles, intermediate and final spin cycles
Notes -For programmes 8 and 9, we advise against exceeding a wash load of 3.5 kg. -For programme 13 we advise against exceeding a wash load of 2 kg. -For the anti-crease function: see Easy iron, opposite page. The information contained in the table is purely indicative. Special programme Daily (programme 11 for Synthetics) is designed to wash lightly soiled garments in a short amount of time: it only lasts 30 minutes and allows you to save on both time and energy. By setting this programme (11 at 30C), you can wash different fabrics together (except for woollen and silk items), with a maximum load of 3 kg. We recommend the use of liquid detergent.
Turn the TEMPERATURE knob to set the wash temperature (see Programme table on page 18). The temperature can be lowered, or even set to a cold wash ( ).
Setting the temperature
Turn the SPIN SPEED knob to set the spin speed for the programme selected. The maximum spin speeds for each programme are as follows: Programmes Maximum spin speed Cotton 1000 rpm Synthetics 800 rpm Wool 600 rpm Silk no. The spin speed can be lowered, or the spin cycle can be excluded altogether by selecting symbol The washing machine will automatically prevent you from selecting a spin speed higher than the maximum speed for each programme.
Setting the spin speed
To enable a function: 1. press the button corresponding to the desired function, according to the table below; 2. the function is enabled when the corresponding button is illuminated. Note: The rapid flashing of the button indicates that the corresponding function cannot be selected for the programme set.
Enabled with programmes:
Effect Delays the start of the wash by up to 9 hours. Bleaching cycle designed to remove the toughest stains. This option reduces the amount of creasing on fabrics, making them easier to iron. Increases the efficiency of the rinse.
Comments Press the button repeatedly until the LED corresponding to the desired delay is turned on. The fifth time the button is pressed, the function will be disabled. N.B.: Once you have pressed the Start/Reset button, the delay can only be decreased if you wish to modify it. Please remember to pour the bleach into extra compartment 4 (see page 20). This function is incompatible with the EASY IRON function. When this function is set, programmes 4, 5, 6, 7 will end with the laundry left to soak (Anti-crease) and the Rinse cycle phase LED will flash. - to conclude the cycle, press the START/RESET button; - to run the draining cycle alone, set the knob to the relative symbol and press the START/RESET button. This function is incompatible with the STAIN REMOVAL function. Recommended when the appliance has a full load or with large quantities of detergent.
2, 3, 4, 5, Rinse cycle.
3, 4, 5, 6, 7, 8, 9, 10, Rinse cycle.
1, 2, 3, 4, 5, 8, 9, 10, 12, 13, Rinse cycle.
Detergents and laundry
Good washing results also depend on the correct dose of detergent: adding too much detergent won't necessarily make for a more efficient wash, and may in fact cause build up on the interior of your appliance and even pollute the environment. Open up the detergent dispenser and pour in the detergent and fabric softener, as follows.
The use of extra compartment 4 excludes the possibility of using the pre-wash cycle. In addition, the bleach cycle cannot be run with programmes 7 (Silk) and Daily (see page 18).
Preparing your laundry
Divide your laundry according to: - the type of fabric/the symbol on the label. - the colours: separate coloured garments from whites. Empty all pockets and check for loose buttons. Do not exceed the weight limits stated below, which refer to the weight when dry: Sturdy fabrics: max 5 kg Synthetic fabrics: max 2.5 kg Delicate fabrics: max 2 kg Wool: max 1 kg
How much does your laundry weigh?
compartment 1: Detergent for pre-wash (powder) Before pouring in the detergent, make sure that extra compartment 4 has been removed. compartment 2: Detergent for the wash cycle (powder or liquid) Liquid detergent should only be poured in immediately prior to the wash cycle start. compartment 3: Additives (fabric softeners, etc.) The fabric softener should not overflow from the grid. extra compartment 4: Bleach
sheet 400-500 g pillow case 150-200 g tablecloth 400-500 g bathrobe 900-1,200 g towel 150-250 g
Curtains: fold curtains and place them in a pillow case or mesh bag. Wash them separately without exceeding half the appliance load. Use programme 7 which excludes the spin cycle automatically. Quilted coats and windbreakers: if they are padded with goose or duck down, they can be machine-washed. Turn the garments inside out and load a maximum of 2-3 kg, repeating the rinse cycle once or twice and using the delicate spin cycle. Wool: for best results, use a specific detergent, taking care not to exceed a load of 1 kg.
Do not use hand wash detergent because it may form too much foam.
Traditional bleach should be used on sturdy white fabrics, and delicate bleach for coloured fabrics, synthetics and for wool.
Place extra compartment 4, provided, into compartment 1. When pouring in the bleach, be careful not to exceed the "max" level indicated on the central pivot (see figure). To run the bleach cycle alone, pour the bleach into extra compartment 4 and set the Rinse programme. To bleach during a wash cycle, pour in the detergent and fabric softener, set the desired programme and enable the Stain removal option (see page 19).
Precautions and advice
The washing machine was designed and built in compliance with the applicable international safety regulations. The following information is provided for your safety and should consequently be read carefully.
The crossed out "wheeled bin" symbol on the product reminds you of your obligation, that when you dispose of the appliance it must be separately collected. Consumers should contact their local authority or retailer for information concerning the correct disposal of their old appliance. Disposing of an old washing machine: before scrapping your appliance, cut the power supply cable and remove the appliance door.
This appliance has been designed for nonprofessional, household use and its functions must not be changed. This washing machine should only be used by adults and in accordance with the instructions provided in this manual. Never touch the washing machine when barefoot or with wet or damp hands or feet. Do not pull on the power supply cable to unplug the appliance from the electricity socket. Pull the plug out yourself. Do not open the detergent dispenser while the appliance is in operation. Do not touch the drain water as it could reach very high temperatures. Never force the washing machine door: this could damage the safety lock mechanism designed to prevent any accidental openings. In the event of a malfunction, do not under any circumstances touch internal parts in order to attempt repairs. Always keep children well away from the appliance while in operation. The appliance door tends to get quite hot during the wash cycle. Should it have to be moved, proceed with the help of two or three people and handle it with the utmost care. Never try to do this alone, because the appliance is very heavy. Before loading your laundry into the washing machine, make sure the drum is empty.
Saving energy and respecting the environment
Environmentally-friendly technology If you only see a little water through your appliance door, this is because thanks to the latest technology, your washing machine only needs less than half the amount of water to get the best results: an objective reached to respect the environment. Saving on detergent, water, energy and time To avoid wasting resources, the washing machine should be used with a full load. A full load instead of two half loads allows you to save up to 50% on energy. The pre-wash cycle is only necessary on extremely soiled garments. Avoiding it will save on detergent, time, water and between 5 and 15% energy. Treating stains with a stain remover or leaving them to soak before washing will cut down the need to wash them at high temperatures. A programme at 60C instead of 90C or one at 40C instead of 60C will save up to 50% on energy. Use the correct quantity of detergent depending on the water hardness, how soiled the garments are and the amount of laundry you have, to avoid wastage and to protect the environment: despite being biodegradable, detergents do contain ingredients that alter the natural balance of the environment. In addition, avoid using fabric softener as much as possible. If you use your washing machine from late in the afternoon until the early hours of the morning, you will help reduce the electricity board's peak load. The Delay Timer option (see page 19) helps to organise your wash cycles accordingly. If your laundry has to be dried in a tumble dryer, select a high spin speed. Having the least water possible in your laundry will save you time and energy in the drying process.
Programmes Detergents Precautions Care Troubleshooting
Disposal of old electrical appliances The European Directive 2002/96/EC on Waste Electrical and Electronic Equipment (WEEE), requires that old household electrical appliances must not be disposed of in the normal unsorted municipal waste stream. Old appliances must be collected separately in order to optimise the recovery and recycling of the materials they contain and reduce the impact on human health and the environment.
Care and maintenance
Cutting off the water or electricity supply
Turn off the water tap after every wash. This will limit the wear of your appliance's water system and also prevent leaks. Unplug your appliance when cleaning it and during all maintenance operations.
Cleaning the pump
The washing machine is fitted with a self-cleaning pump that does not require any maintenance. Sometimes, small items (such as coins or buttons) may fall into the pre-chamber that protects the pump, situated in the lower part of the same.
Make sure the wash cycle has ended and unplug the appliance.
To access the pre-chamber: 1. using a screwdriver, remove the cover panel on the lower front of the washing machine (see figure);
Cleaning your appliance
The exterior and rubber parts of your appliance can be cleaned with a soft cloth soaked in lukewarm soapy water. Do not use solvents or abrasives.
Cleaning the detergent dispenser
Remove the dispenser by pulling it out (see figure). Wash it under running water; this operation should be repeated frequently.
2. unscrew the lid rotating it anticlockwise (see figure): a little water may trickle out. This is perfectly normal;
Caring for your appliance door and drum
Always leave the appliance door ajar to prevent unpleasant odours from forming. 3. clean the interior thoroughly; 4. screw the lid back on; 5. reposition the panel, making sure the hooks are securely in place before you push it onto the appliance.
Checking the water inlet hose
Check the water inlet hose at least once a year. If you see any cracks, replace it immediately: during the wash cycles, water pressure is very strong and a cracked hose could easily split open.
Never use hoses that have already been used.
Your washing machine could fail to work. Before calling for Assistance (see page 24), make sure the problem can't easily be solved by consulting the following list.
The washing machine won't start. The wash cycle won't start.
The appliance is not plugged into the socket, or not enough to make contact. There has been a power failure. The appliance door is not shut properly. button has not been pressed. The The START/RESET button has not been pressed. The water tap is not turned on. A delayed start has been set (using the Delay Timer, see page 19). The water inlet hose is not connected to the tap. The hose is bent. The water tap is not turned on. There is a water shortage. The water pressure is insufficient. The START/RESET button has not been pressed.
The washing machine fails to load water.
The washing machine continuously loads and unloads water.
The drain hose is not fitted between 65 and 100 cm from the floor (see page 15). The free end of the hose is underwater (see page 15). The wall drainage system doesn't have a breather pipe. If the problem persists even after these checks, turn off the water tap, switch the appliance off and call for Assistance. If the dwelling is on one of the upper floors of a building, there may be drain trap problems causing the washing machine to load and unload water continuously. In order to avoid such an inconvenience, special anti-drain trap valves are available in shops. The programme does not foresee the draining: some programmes require enabling the draining manually (see page 18). The Easy iron option is enabled: to complete the programme, press the START/RESET button (see page 19). The drain hose is bent (see page 15). The drain duct is clogged. The drum was not unblocked correctly during installation (see page 14). The washing machine is not level (see page 14). The washing machine is closed in between furniture cabinets and the wall (see page 14). The water inlet hose is not screwed on correctly (see page 14). The detergent dispenser is obstructed (to clean it, see page 22). The drain hose is not secured properly (see page 15). Call for Assistance because this means there is an abnormality.
The washing machine does not drain or spin.
The washing machine vibrates too much during the spin cycle.
The washing machine leaks.
The ON-OFF/DOOR LOCK Led flashes rapidly at the same time as at least one other LED. There is too much foam.
The detergent is not suitable for machine washing (it should bear the definition "for washing machines" or "hand and machine wash", or the like). You used too much detergent.
09/2005 - Xerox Business Services
Before calling for Assistance: Check whether you can solve the problem on your own (see page 23); Restart the programme to check whether the problem has been solved; If this is not the case, contact an authorised Technical Service Centre on the telephone number provided on the guarantee certificate.
Always request the assistance of authorised servicemen.
Notify the operator of: the type of problem; the appliance model (Mod.); the serial number (S/N). This information can be found on the data plate situated on the rear of the washing machine.
G1150 Lexmark T420 D-550 Zoom RQ-SX76 GT-I8000 M8 Srlp18 SCH-B540 T303C DT 150 IST D BL-WV10 BAR686 DLS W710 ZWS2105W Nokia E66 94124 WTC1398N KX-TGA810EX Sun Twin P-7000 Photo 750 BT1100-2003 1000S Murano-2007 RCD-971 GT-M7600L XG-NV4SE KDC-W237 Syncmaster 720N SCX-5315 Printer BH5612 Fortemanager Alesis HR16 WR250FP PCG-F270 NN-D851 32LB220B4 Piano SP 350 PPM1012 3003 C CR14A DSC-TX5 EVO N200 Pentax MZ-3 21PT1820 VGN-FW31J KDL-46W4220 Cruise Powershot A540 Blue BOX Officejet 6110 Concord 3040 ALL-model-navigation MY700X M2N32-ws-PRO TL543C Roland E-28 C165BEE SRT 6006 TXL32C2EA Cube-30 Bass Vdrd50 SS-RG440 P4VMM232A SP-565 UZ 81035 A300D Teachers M-5130SH Special Blackbox SH-D162C DLG2532W Fishfinder CN-20 MS-430 U Pajero Review Kv-c1000 MG-583MCG Enhwi-3GN3 CL-20E22 LE19B650 1310I APS57 SW160010-DR PRO 7949 DCR-TRV270E TXP42C10Y MCM279 DCM-17WT DCR-TRV410 Professional Forever 400 DEH 434R Keyence LV Sportster XV-DV99 Audioline 25
manuel d'instructions, Guide de l'utilisateur | Manual de instrucciones, Instrucciones de uso | Bedienungsanleitung, Bedienungsanleitung | Manual de Instruções, guia do usuário | инструкция | návod na použitie, Užívateľská príručka, návod k použití | bruksanvisningen | instrukcja, podręcznik użytkownika | kullanım kılavuzu, Kullanım | kézikönyv, használati útmutató | manuale di istruzioni, istruzioni d'uso | handleiding, gebruikershandleiding
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101