Here you can find all about Infocus LP340B like manual and other informations. For example: review, bulb.
Infocus LP340B manual (user guide) is ready to download for free.
On the bottom of page users can write a review. If you own a Infocus LP340B please write about it to help other people. [ Report abuse or wrong photo | Share your Infocus LP340B photo ]
Infocus LP340B Home Cinema Projector, size: 205 KB
Infocus LP340B Reference Guide
Infocus LP340B Installation Instruction
Infocus LP340B Document
User reviews and opinions
No opinions have been provided. Be the first and add a new opinion/review.
Do you want to control the computers mouse from the projectors remote?
NOTE: The USB mouse is supported for use with Windows 98, Windows 2000, and Apple OS 8.5 and higher only.
1 Plug the USB cable into the USB mouse connector on your computer. If your computer has a PS/2 mouse connector and not a USB mouse connector, you can purchase the optional CableWizard3 which has a PS/2 mouse connector or the Executive Remote IR Receiver. See Optional Accessories on page 43.
Do you want to play your computers audio on the projector?
1 Plug either end of the audio cable into the audio connector on your computer. 2 Plug the other end of the audio cable into the on the projector. connector
NOTE: You do not need to restart your computer after connecting a USB mouse to use it (it is hotpluggable).
Now youre ready to power up the projector and your laptop. Skip to Powering up the Projector and Adjusting the Image on page 13.
Connecting a Video Player 1 If your video player uses a round, one-prong composite video connector, youll need only the audio cable, audio adapter, and composite video cable that shipped with the projector.
If your video player uses a round, four-prong S-video con-
nector, youll need an S-video cable in addition to the audio cable and audio adapter. The S-video cable is sold separately. (See Optional Accessories on page 43.) 2 Plug the composite video cables yellow connector into the video-out connector on your video player (Figure 7). This connector may be labeled To Monitor.
If youre using an S-video cable, connect it to the S-video
NOTE: HDTV sources must be connected to the projector using the computer cable (not a composite or S-video cable). See the previous pages for details on connecting this cable.
out connector on the video player (Figure 8). 3 Plug the other yellow connector into the composite video connector on the projector.
If youre using S-video, plug the other end of the cable into
the S-video connector
on the projector (Figure 8).
composite video cable
FIGURE 7 Connecting the projector to a video player using the standard video cable (with composite video connector) and the audio cable and adapter
FIGURE 8 Connecting the projector to a video player using an S-video cable and the audio cable and adapter
NOTE: The audio adapter is provided so that the same audio cable used to connect a computer can be used with the adapter to connect a VCR.
4 Plug the audio adapters white connector into the left audio out connector on your video player. Plug the adapters red connector into the right audio out connector on the video player (Figure 7 and Figure 8). 5 Plug the audio adapters other end into the audio cable. 6 Plug the audio cable into the audio in projector. connector on the
disk mouse right mouse button
left mouse button (on underside of remote) FIGURE 9 Remote control
NOTE: If the remote is inactive for several minutes, it sleeps to conserve battery life. Press any button except the disk mouse to re-activate the remote.
Press anywhere on the edge of the disk mouse to move the cursor on the screen. You can move the cursor at any angle by pressing the corresponding edge of the disk. The mouse button on the top of the remote simulates your computers right mouse button; the button on the bottom simulates your computers left mouse button. See Using the Keypad and Remote Buttons starting on page 18 for a description of the four function buttons. If you are creating presentations in Microsoft PowerPoint, you can use the remotes mouse buttons to navigate through your presentation while in Slide Show mode. To configure PowerPoint for this, choose Options from the Tools menu, click the View Tab, de-select the Popup Menu on Right Mouse Click option in the Slide Show section, then click OK. Then, when youre in PowerPoints Slide Show mode, a left click advances to the next slide and a right click returns to the previous slide (other PowerPoint modes are not affected).
Adjusting the Projector To focus the image, rotate the focus ring (Figure 10) until the image is clear. To zoom the image, rotate the zoom ring. This adjusts the image size without affecting focus.
FIGURE 10 Focus ring and zoom ring
The projector is equipped with a self-locking, quick-release elevator foot and button and a leveling knob (Figure 11). To raise the projector: 1 Press and hold the elevator button (Figure 11). 2 Raise the projector to the height you want, then release the button to lock the elevator foot into position. If necessary, turn the leveling knob at the rear of the projector to adjust the angle of the projected image.
elevator foot elevator button (under finger)
FIGURE 11 Adjusting the height of the projector
Using the Keypad and Remote Buttons While the menus are displayed, the volume, source, and standby buttons on the keypad act as menu navigation buttons. See Using the On-Screen Menus on page 20 for details.
left mouse button
right mouse button
FIGURE 12 Keypad and remote buttons Menu
Press the menu button to open the on-screen menus. Press menu again to close the menus. When you close the menus, the projector saves any changes you made. For more information about the on-screen menus, see page 20.
Use the mouse buttons to adjust settings in the menus. See Using the On-Screen Menus on page 20.
Source (keypad only) or Computer and Video (remote only)
When you have more than one source (computer and video) connected to the projector, select between them by pressing the source button on the keypad or the computer or video button on the remote.
When you press standby, the display and audio turn off and a blank screen is displayed for 15 minutes. You can change the amount of time the projector stays in standby mode; see Standby Time on page 27 for details. The LED lights orange while the projector is in standby.
If you press standby again within 15 minutes, the projector
returns to normal operations immediately. The LED changes from orange to green.
If you press standby again after 15 minutes, there is about a
60 second delay before the lamp turns back on. The LED flashes green while the lamp is re-lighting.
If you dont press standby again, the lamp turns off after 15
minutes. The LED lights orange while the projector is in standby.
Volume (keypad only)
To increase the volume, press volume + ume, press volume.
. To decrease the vol-
Volume adjustments are saved for each source you have connected.
Using the On-Screen Menus The projector has six drop-down menus that allow you to make image adjustments and change a variety of settings. Most of these adjustments arent available directly from the keypad. To open the on-screen menus, press the menu button on the keypad or remote. This changes the volume, source, and standby buttons on the keypad to menu navigation buttons. Press the corresponding buttons to move the cursor up, down, left, or right, or use the disk mouse on the remote. To select a menu, move the cursor left or right to highlight the menu you want. The drop-down menu appears.
NOTE: Some menu items may be grayed out (dimmed) at certain times. This indicates the item is not applicable to your setup (for example, video standards do not apply to computer sources) or the item is not enabled until another
selection is made (for example, Manual Tracking is not available until Auto Image is turned off).
volume volume + source
Display > Audio Brightness Contrast Tint Color Sharpness Blank screen Reset all
use these four buttons to navigate through the menus
FIGURE 13 Keypad navigation buttons and drop-down menu
To change a menu setting, use the up and down navigation buttons on the keypad or the disk mouse on the remote to move the cursor up and down to the item you want to change (the selected item is highlighted), then use the left and right mouse buttons to adjust a setting. Some submenus, such as Brightness, consist of a slider bar you use to increase or decrease a value; some submenus, such as Standby Time, consist of options you scroll through to select the desired one. All changes are saved when you close the menus. To access another menu, use the left and right navigation buttons to move to the desired menu.
FIGURE 14 Display menu Brightness
Adjusting the brightness changes the intensity of the image.
Press the left mouse button to darken the image. Press the right mouse button to lighten the image. Contrast
The contrast controls the degree of difference between the lightest and darkest parts of the picture. Adjusting the contrast changes the amount of black and white in the image.
Press the left mouse button to decrease the contrast. Press the right mouse button to increase the contrast, making
the blacks appear blacker and the whites appear whiter.
The tint adjusts the red-green color balance in the projected image.
Press the left mouse button to increase the amount of green in
Press the right mouse button to increase the amount of red in
The color setting adjusts a video image from black and white to fully saturated color.
Press the left mouse button to decrease the amount of color in
Press the right mouse button to increase the amount of color in
This setting adjusts the sharpness of a video image and is available on the LP350 only.
Press the left mouse button to decrease the sharpness. Press the right mouse button to increase the sharpness. Blank Screen
Blank Screen determines what color is displayed when there is no active source and when the projector is in standby. Click the left or right mouse button to toggle between blue and black.
Click the left or right mouse button to reset all the options (except Language, Video Standard, Rear and Ceiling Projection, Plug and Play, and Standby Time) in all the menus to their original settings.
Audio > Image Volume Treble Bass
FIGURE 15 Audio menu Volume Press the left mouse button to decrease the volume. Press the right mouse button to increase the volume. NOTE: Changing the volume using the menu is the same as changing it using the keypad. Treble
For video sources, Resize allows you to select from among four different re-sizing options. The default is Standard, which resizes the image from its original version to fit a standard 4x3 aspect ratio screen. Widescreen Letterbox preserves the 16x9 aspect ratio of the original theater version, but the image is placed in a 4x3 space, so black bars appear at the top and bottom of the image. Enhanced Widescreen also preserves the aspect ratio of the original theater version and is designed to be used with content that is Enhanced for Widescreen TVs. This option yields more detail than Widescreen Letterbox. Native reduces the Standard size to match the height of Enhanced Widescreen.
The projector adjusts signal synchronization automatically for most computers. But if the projected computer image looks fuzzy or streaked, try turning Auto Image off then back on again. If the image still looks bad, try adjusting the signal synchronization manually: 1 Turn Auto Image off. 2 Highlight Manual sync, then press the left or right mouse button repeatedly until the image is sharp and free of streaks.
The projector adjusts tracking automatically to match the video signal from your computer. However, if the display shows evenly spaced, fuzzy, vertical lines or if the projected image is too wide or too narrow for the screen, try turning Auto Image off then back on again. If the image is still bad, try adjusting the tracking manually: 1 Turn Auto Image off. 2 Highlight Manual tracking, then press the left or right mouse button repeatedly until the fuzzy vertical bars are gone.
NOTE: The Manual Sync, Manual Tracking, Horiz. Position and Vert. Position options are available only for analog computer sources. The projector sets these options automatically for digital computer and video sources.
Follow these steps to manually adjust the horizontal position: 1 Turn Auto Image off. 2 Highlight Horizontal position, then press the left mouse button to move the image right or press the right mouse button to move the image left. Positioning adjustments are saved when you power off the projector.
Follow these steps to manually adjust the vertical position. 1 Turn Auto Image off. 2 Highlight Vertical position, then press the left mouse button to move the image down or press the right mouse button to move the image up. Positioning adjustments are saved when you power off the projector.
Display Audio Image
Controls > Language Status Video standard Standby time 1 minute Ceiling projection off Rear projection off Default source computer 1 analog Auto source select off Plug and Play off Display messages on Display startup screen on
FIGURE 17 Controls menu
When Video standard is set to Auto, the projector attempts to pick the video standard (NTSC, NTSC 4.43, PAL, PAL-M, PAL-N, PAL-60, or SECAM) automatically based on the input signal it receives. (The video standard options may vary depending on your region of the world.) If the projector is unable to detect the correct standard, the colors might not look right or the image might appear torn. If this happens, manually select a standard by clicking the left or right mouse button and cycling through the standards.
NOTE: If you already know the video standard used in your geographical area, its often best to manually select it.
This option lets you select how long the lamp stays on and the blank screen is displayed when the projector enters standby mode before the projector turns off. Select among instant, 1, 5, 10, 15 and 30 minutes and 1 and 2 hours by clicking the left or right mouse button and cycling through the options.
Ceiling Projection When you turn Ceiling Projection on, the projector turns the
image upside down for ceiling-mounted projection. Highlight Ceiling Projection, then click the left or right mouse button to turn this feature on and off.
When you turn Rear Projection on, the projector reverses the image so you can project from behind a translucent screen. Highlight Rear Projection, then click the left or right mouse button to turn this feature on and off.
Default Source toggles among Computer 1 analog, Computer 1 digital, Computer 2, and Video. This determines which source the projector checks first for active video during power-up. Highlight Default Source and click the left or right mouse button to toggle among the options.
Lamp hours used Computer resolution Horizontal refresh rate Vertical refresh rate Mute status Source Software version Startup screen version Boot version CableWizard version
FIGURE 19 Status menu Lamp hours used
0039 1024x768 60.03 KHz 75.04 Hz off computer 1 analog 1.0 1.0 1.0 1.0
Indicates how many hours the current lamp has been in use. The counter starts at zero hours and counts each hour the lamp is in use. After 2,000 hours of use, the message Change Lamp temporarily appears on the screen when the projector is turned on. Change the lamp within the next 50 hours. After 2,050 hours, the LED flashes orange and the lamp will not light. See Replacing the Projection Lamp on page 33 for details.
Shows your computers resolution setting. To change this, go to your computers Control Panel and adjust the resolution in the Display tab. See your computers users guide for details.
Horizontal refresh rate
The time period that one horizontal line is displayed.
Vertical refresh rate
The time period that one video frame is displayed.
Indicates if the audio is muted.
Indicates the active source, Computer 1 analog, Computer 1 digital, Computer 2, and Video.
Indicates the projectors software version. This information is useful when contacting Technical Support.
Startup screen version
Indicates the projectors startup screen version. This information is useful when contacting Technical Support.
Indicates the projectors boot software version. This information is useful when contacting Technical Support.
Indicates the CableWizards software version. This information is useful when contacting Technical Support.
MAINTENANCE & TROUBLESHOOTING
This section describes how to:
clean the lens replace the projection lamp replace the batteries in the remote use the security lock feature troubleshoot the projector
Cleaning the Lens Follow these steps to clean the projection lens: 1 Apply a non-abrasive camera lens cleaner to a soft, dry cloth.
Avoid using an excessive amount of cleaner, and dont
apply the cleaner directly to the lens.
Abrasive cleaners, solvents or other harsh chemicals might
scratch the lens. 2 Lightly wipe the cleaning cloth over the lens in a circular motion. 3 If you dont intend to use the projector immediately, replace the lens cap. Replacing the Projection Lamp The lamp hour counter in the Status menu counts the number of hours the lamp has been in use. After 2,000 hours of use, the message Change Lamp temporarily appears on the screen when the projector is turned on. Change the lamp within the next 50 hours. After 2,050 hours, the LED flashes orange and the lamp will not light. You can order new lamp modules from your InFocus dealer. See Accessories on page 42 for information. Follow these steps to replace the projection lamp: 1 Turn off the projector and unplug the power cord. 2 Wait 30 minutes to allow the projector to cool thoroughly.
WARNING: To avoid burns, allow the projector to cool for at least 30 minutes before you open the lamp module door. Never extract the lamp module while the projector is operating.
3 Invert the projector on a soft flat surface, then insert a small screwdriver or other flat object into the tabs on the lamp module door (Figure 20) and gently pry the door up.
WARNING: Be extremely careful when removing the lamp module. In the unlikely event that the bulb ruptures, small glass fragments may be generated. The lamp module is designed to contain these fragments, but use caution when removing the lamp module.
FIGURE 20 Removing the lamp door
4 Pull the lamp door up and remove it.
CAUTION: Never operate the projector with the lamp door open or removed. This disrupts the air flow and causes the projector to overheat.
5 Loosen the two non-removable screws on the outside of the module (Figure 21).
FIGURE 21 Loosening the screws on the lamp module
6 Lift and grasp the pull tab and lift the module out (Figure 22). Dispose of the lamp module in an environmentally proper manner.
FIGURE 22 Removing the lamp module
7 Install the new lamp module, being sure to align the connectors properly. 8 Push the module in until it is flush with the bottom case of the projector. 9 Tighten the screws on the outside of the module. 10 Replace the lamp door by inserting the hooks on the lamp door into the slots on the projector and pressing the lamp door into place. If the lamp door does not fit properly or bulges out, remove the door and re-seat the lamp module. 11 Plug in the power cord and press the Power button to turn the projector back on. 12 To reset the lamp hour counter in the Status window, press and hold the volume - button, then press the menu button (while still holding down the volume - button) for 5 seconds. Verify that the counter was reset by pressing the menu button and viewing the counter in the Status window.
WARNING: Do not drop the lamp module or touch the glass bulb! The glass may shatter and cause injury.
Replacing the Batteries in the Remote Control The life of the batteries depends on how often and how long you use the remote. Symptoms of low battery charge include erratic responses when using the remote and a reduced range of operation. Follow these steps to replace the batteries: 1 Turn the remote face down in your hand. 2 Slide the battery cover off the end of the remote. 3 Remove the old batteries and dispose of them in an environmentally proper manner. 4 Install two new AAA alkaline batteries. Make sure you install each in the correct direction. 5 Slide the battery cover back on the remote. Using the Security Lock The projector has a security connector for use with a PC Guardian Cable Lock System (Figure 23). See Optional Accessories on page 43 for ordering information. Refer to the information that came with the lock for instructions on how to use it to secure the projector.
FIGURE 23 Installing the security lock
Troubleshooting Problem: The projector is not running Make sure that the power cord is properly connected to a fully functional AC electrical outlet. Make sure that the power cord is also properly connected to the projector.
If the projector is plugged into a power strip, make sure the
power strip is turned on.
Make sure the projector is turned on.
Problem: Projector is running, but nothing appears on projection screen Make sure you have removed the lens cap on the projection lens at the front of the projector.
Make sure the lamp has not been in use for over 2,050 hours.
The lamp automatically shuts off at 2,050 hours and the LED blinks orange. See Replacing the Projection Lamp on page 33.
Check the projectors lamp to ensure that it is securely con-
nected in the lamp module. Make sure the lamp door is installed. See Replacing the Projection Lamp on page 33. Problem: Only the start-up screen displays Verify that the cables are connected correctly. See page 9 through page 10 for connection procedures.
Make sure that the cables do not have any bent pins. Verify that the proper input source is connected. See Source
(keypad only) or Computer and Video (remote only) on page 18.
You might need to turn everything off and power up the
equipment again in the proper order. Refer to your computers documentation to determine the correct order.
Make sure your laptops external video port is turned on. See
the Portable and Laptop Activation Chart on page 44 or your computers manual for details.
Make sure your computers video board is installed and con-
Make sure your computer has a compatible video board. The
projector isnt CGA, EGA or SXGA compatible. If youre using Windows 98: 1 Open My Computer icon, the Control Panel folder and then the Display icon. 2 Click the Settings tab. 3 Verify that the Desktop area is set to 1024x768 or less. Problem: Color or text not being projected You might need to adjust the brightness up or down until the text is visible. Refer to Brightness on page 21 for more information. Problem: The screen resolution is not right Make sure the computers video card is set for a resolution of no greater than 1024x768. Problem: Image isnt centered on the screen Move the projector to reposition the image.
Reposition the image using the menu. Refer to Horizontal
Specifications The projector must be operated and stored within the temperature and humidity ranges specified.
Temperature Operating Non-operating Humidity Operating and non-oper. 50 to 104 F (10 to 40 C) at sea level 50 to 95 F (10 to 35 C) at 10,000 feet -4 to 158 F (-20 to 70 C)
10% to 95% relative humidity, non-condensing
Dimensions 3.9 x 10.9 x 11.2 inches (9.9 x 27.7 x 28.6 cm) Weight 6.7 lbs. (3 kg) unpacked Altitude Operating Non-operating Optics Focus Range Lamp Type
0 to 10,000 feet (3,048 meters) 0 to 20,000 feet (6,096 meters)
4.9 - 16 feet (1.5-5 m)
270-watt SHP lamp
Input Power Requirements 100-120VAC 5A;50/60Hz 200-240VAC 3A; 50Hz Audio Input Input Impedance Maximum Input Voltage Sensitivity Connector Type
10K ohm nominal, AC coupled (LIN + RIN)PEAK < 4.5 V for THD 0.3% LIN or RIN < 2.0 Vrms for THD 0.3% 100 mV at 1 KHz for 88 dB SPL at 1 meter 3.5 mm (1/8 inch) stereo phone mini
Standard Accessories (ship with the projector) Quick Start card Users Guide Soft Case for LP350 Soft Case for LP340B Shipping Box Analog Computer Cable 6 ft (1.8 m) Composite Video Cable 6 ft (1.8 m) Computer Audio Cable 6 ft (1.8 m) Audio Adapter (RCA to 3.5mm) Executive Plus Remote Projection Lamp Module Lens Cap Online Users Guide CD-ROM Part Number 009-0571-xx 010-0276-xx 110-0299-xx 110-0414-xx 110-0300-xx 210-0185-xx 210-0176-xx 210-0118-xx 210-0177-xx HW-EXPLUS SP-LAMP-LP3E 340-0686-xx 010-0116-xx
NOTE: Use only InFocusapproved accessories. Other products have not been tested with the projector.
Power Cords (one ships with projector, type depends on country) North American Power Cord Australian Power Cord UK Power Cord European Power Cord Danish Power Cord Swiss Power Cord 210-0023-xx 210-0027-xx 210-0028-xx 210-0029-xx 210-0030-xx 210-0031-xx
NOTE: You can purchase these items by contacting your dealer or InFocus Catalog Sales at 1-800-660-0024.
Optional Accessories Deluxe Carry Case Shipping Case (ATA approved) Deluxe Travel Case Deluxe Travel Case with detachable pocket Digital Computer Cable (LP350 only) Digital/Analog Interface Card (LP350 only) Ceiling Mount Kit Ceiling Mount Plate CableWizard2 CableWizard2 Serial Cable CableWizard3 CableWizard Lite, 6.5 ft CableWizard Extension Cable, non-plenum rated, 60.7 ft CableWizard Extension Cable, plenum-rated, 60.7 ft Macintosh Adaptor CableWizard RS232 Adaptor Full-Feature LaserPro Remote Control Wired LaserPro Cable GyroMouse RF Remote (US, Mexico, Canada, UK only) Executive Remote IR Receiver Remote Point RF Remote with LaserPointer (US, Mexico, Canada only) PC Guardian Projector Cable Lock S-Video Cable 40 Portable Projection Screen 50 Portable Projection Screen 60 Deluxe Insta-Theatre Screen Replacement Projection Lamp Module 3rd Year Extended Warranty (1 year extension) 4th Year Extended Warranty (2 year extension) CA-C132 CA-C194 CA-C141 CA-C182 SP-DVI-D SP-DVI-CARD SP-CEIL-LM3X SP-CEIL-P3 SP-CW2 210-0107-xx SP-CW3 SP-CW2LITE SP-CW2EXT SP-CW2EXTP SP-MACADPT SP-CWRS232 HW-LASERPRO SP-WIREM HW-RF-GPRO HW-EXRCVR HW-RF-REMLSR SP-LOCK SP-SVIDEO HW-PORTSCR40 HW-PORTSCR50 HW-DLXSCRN SP-LAMP-LP3E EW-1YEAR EW-2YEAR NOTE: You can purchase these items by contacting your dealer or InFocus Catalog Sales at 1-800-660-0024.
automatic FN-F2 dip switch to CRT dip switch to CRT setup screen option Ctrl-Alt-Shift-C FN-F10 FN-F3 FN-F1/FN-F1 again simultaneous
Computer Grid* **
Key command to activate port FN-F2, choose auto or simultaneous Ctrl-Alt-Tab FN-F7 FN-F10 setup screen option automatic reboot, enter setup menu FN-F7, select choice from setup menu FN-F1, select choice FN-F5, select choice PS/2 SC select choice (CRT, LCD, etc.)
Key command to de-activate port FN-F2 Ctrl-Alt-Tab FN-F7 FN-F10 setup screen option warm reboot FN-F2
Hitachi Honeywell Hyundai IBM 970* IBM ThinkPad**
Infotel Kaypro Kris Tech Leading Edge Mac Portable 100 Mac PowerBook 140, 145, 150, 170 160, 165, 180, 520, 540, 5300 210, 230, 250, 270, 280, 2300 Magitronic Mastersport Micro Express* Micron Microslate*
FN-F12 boot up, monitor plugged in FN-F8 FN-T
FN-F12 unplug monitor FN-F8 FN-T
no video port: not compatible
no video port: requires a 3rd-party interface Control Panel folder, PowerBook Display folder; Activate Video Mirroring warm reboot
requires Apple Docking Station or Mini Dock FN-F4 FN-F2 automatic FN-F2 automatic FN-F4 FN-F1 warm reboot FN-F2 warm reboot
Computer Mitsubishi NCR NEC* **
Key command to activate port SW2 On-Off-Off-Off setup screen option setup screen option CRT at the DOS prompt FN-F3
Key command to de-activate port SW2 Off-On-On-On setup screen option setup screen option LCD at the DOS prompt FN-F3 automatic FN-O/* FN-F0 Ctrl-Alt-> FN-F2 Ctrl-Alt-S at bootup setup screen option setup screen option dip switch to LCD Ctrl-Shift-M Ctrl-Alt-Insert setup screen option FN-F5 setup screen option setup screen option FN-F6 Ctrl-Alt-Home FN-Home FN-F5 setup screen option FN-F7 FN-F5 Automatic Ctrl-Alt-F10 software driven FN-F10 FN-F2
Olivetti* Packard Bell* ** Panasonic Prostar Samsung* Sanyo Sharp Sun SPARCDataview Tandy** Tangent Texas Instruments* Top-Link* ** Toshiba* **
automatic FN-O/* FN-F0 Ctrl-Alt-< FN-F2 Ctrl-Alt-S at bootup setup screen option setup screen option dip switch to CRT Ctrl-Shift-M Ctrl-Alt-Insert setup screen option FN-F5 setup screen option setup screen option FN-F6 Ctrl-Alt-End FN-End FN-F5 setup screen option
FN-F7 FN-F5 Automatic
WinBook Wyse Zenith**
Ctrl-Alt-F10 software driven FN-F10 FN-F2
Key command to activate port FN-F1 Ctrl-Shift-D FN-F1
Key command to de-activate port FN-F1 Ctrl-Shift-D FN-F1
* These manufacturers have models that automatically send video to the external CRT port when some type of display device is attached. ** These manufacturers offer more than one key command depending on the computer model.
Using Video Mirroring with a PowerBook Computer When you turn video mirroring (called SimulScan in newer PowerBookssee below) on, the projector displays the same information that appears on your PowerBooks built-in screen. When video mirroring is off, the projector acts like a separate display. To turn on video mirroring for the first time: 1 Open the Monitors control panel; click on Monitor 2. 2 Set the number of colors you want. 3 Open the Control Strip, then click on the monitor icon. 4 Select Turn Video Mirroring On. Now you can turn video mirroring on and off from the Control Strip without having to open the Monitors control panel again. When using video mirroring and high color graphics such as slide shows, the projected image occasionally might turn black and white. If this happens, perform the following steps: 1 Turn off video mirroring. 2 Open the Monitors control panel. 3 Move the white menu bar to Monitor 2 to set the projector as the primary monitor. 4 Restart the PowerBook.
Some newer PowerBooks display images on an external monitor or projector differently than previous ones. When using SimulScan, the projector displays the same information that appears on your PowerBook To select SimulScan: 1 Open the Control Panel, then double-click Monitors and Sound. 2 In the Resolution list, choose the SimulScan mode, then click OK. 3 If this changes your display settings, a dialog box appears. Click OK to confirm the change. 49
Projected Image Size
NOTE: Use the graph and tables to help you determine projected image sizes.
FIGURE 24 Projected image size
NOTE: Visit our website at www.infocus.com for an interactive image size calculator. It is located in the Technical Library in the Service and Support section.
Table 1: Image Size, Width and Height-maximum image size Distance to Screen (feet) 4.Diagonal (feet) 3.0 5.0 7.4 9.9 12.4 18.6 Width (feet) 2.4 4.0 6.0 7.9 9.9 14.9 Height (feet) 1.8 3.0 4.5 6.0 7.4 11.2
Table 2: Image Size, Width and Height-minimum image size Distance to Screen (feet) 4.Diagonal (feet) 2.5 4.0 6.0 8.0 10.0 15.0 Width (feet) 2.0 3.2 4.8 6.4 8.0 12.0 Height (feet) 1.5 2.4 3.6 4.8 6.0 9.0
CableWizard 8 extension cable 43 CableWizard Lite, ordering 43
accessories, ordering 42, 43 activation commands for laptop computers 44 adjusting brightness 21 color 22 contrast 21 height of the projector 17 tint 21 volume 19, 23 altitude limits 41 assistance. See Technical Support audio adapter, connecting 12 audio cable, connecting 10 Audio menu 23 Audio menu options Bass 23 Treble 23 Volume 23 Auto Source Select 28
cases, ordering 42 ceiling-mounted projection 27, 43 centering the image 17, 26 cleaning the projection lens 33 color, adjusting 22 colors dont match monitor colors 39 not displayed 38 compatibility IBM-compatible 2 Macintosh 2 composite video cable connecting 11 computers connecting 9 computers, compatible 2 connecting audio adapter 12 audio cable 10 computers 9 power cord 13 remote 10 USB mouse 10 video player 1112 contrast, adjusting 21 Controls menu 27 Controls menu options Auto Source Select 28 Ceiling Projection 27 Default Source 28 Display Messages 28 Display Startup Screen 29 Plug and Play 28 Rear Projection 28 Standby Time 27 Video Standard 27
bass 23 Blank Screen 22 brightness, adjusting 21 buttons on keypad Menu 18 Source 18 Standby 19 Volume 19
cables audio 10 audio adapter 12 CableWizard extension 43 composite video 11 extension 43 M1-DA analog computer cable 3, 8, 9 ordering 42 power 42 S-video 11, 43
Default Source 28 Display menu 21 Display menu options Blank Screen 22 Brightness 21 Color 22 Contrast 21 Reset All 22 Sharpness 22 Tint 21 Display Messages 28 Display Startup Screen 29 displaying on-screen menus 18 startup screen 29 status messages 28
IBM-compatible computers compatibility 2 image adjusting 13, 15 centering 26 colors dont match computers 39 focusing 17 fuzzy lines 25 has lines or spots 39 not centered 38 not displayed 37 out of focus 38 quality 3839 resolution 1 reversed 28, 39 size 7, 50 streaked 39 too wide or too narrow 38 zooming 17 Image menu 24 Image menu options Auto Image 24 Horiz. Position 26 Keystone 24 Manual Sync 25 Manual Tracking 25 Overscan 24 Resize 24 Vert. Position 26
elevator button/foot 17 extension cable 43
focusing the image 17 fuzzy lines 25
HDTV 2, 11, 24 height adjustment 17
keypad 18 keystone correction 24
lamp ordering 42 replacing 33 turns off unexpectedly 40 lamp hour counter 30, 33, 35 Language menu 29 language, selecting for menus 29 laptop computers activation sequence to allow secondary display 44 compatibility 9 connecting 9 LED 13, 18, 19, 30, 33 lens cap 42 cleaning 33 leveling knob 17 leveling the projector 17 LP340B/350 cases 42 project from behind the screen 27, 28 setting up 7 specifications 41 turning off 14 turning on 13
NTSC video 27
on-screen menus Audio menu 23 changing language of 29 Controls menu 27 Display menu 21 displaying 20 Image menu 24 Language menu 29 making changes to menu functions 20 Status menu 30 overscan 24
PAL video 27 Plug and Play 28 power cord connecting 13 ordering 42 power up sequence 13, 37 PowerPoint slides, advancing with the remote 10, 16 project from behind the screen 28
M1-DA analog computer cable 3, 8, 9 Macintosh computers compatibility 2 connecting 9 Menu button 20 menus. See on-screen menus monitor, projected colors dont match 39 mouse buttons on keypad 18, 20 buttons on remote 15, 20 connecting USB 10
InFocus SP-LAMP-LP3F replacement lamp for LP340 LP340B LP350 LP350G
incl. 20,0% VAT plus delivery charges
celexon UK Ltd Victory House Chequers Road Tharston, Norwich NR15 2YA Registered in England and Wales Company No: 6986551 tel: +44 (0) fax: +44 (0) email@example.com
Non-binding offer. Subject to technical changes. Errors and omissions excepted. Price incl. 20,0% VAT plus delivery charges. 2011 celexon(TM) UK Ltd.
Bulb Pcwa-A220 PS42B430p2 Mouse CTK-2000 Optoma H31 DVD-SH895M VP-D353 VT-14GH10 GT-I5800L Review Rouleau WIM 2160 RTE114 PV520 Console Mk2 6300I DMT-8 FTR9955 TCP50G25 EX-S2 FW405 GT-9700F 8 0 Falcon CQ-C1103NE MP180 Cusl2CBP Deskjet 6980 Yamaha 200 HD80 2T 21F99 NP-R58 Plus Watches Photosmart 420 MH026feea Sram T3 III Gene MDR-IF5K Chair KV-32FQ80E CQ-RDP855 ICD-SX55 Solo 423 Yamaha RY8 MCM108B 2232GW GR-T582G M-08R ZDT111 SPX900 MHC-RG170 MT-42PZ45V F8T013 KX-TC1450W A-90 EX Magicolor 4650 Euroset 832 20-inch Sa660 Korg KP1 Alicante CD34 TT-02 MYX6-2 ICF-CD823 CX-DVP292N DLE6977W Esam 2600 Calmato TR Powershot A490 Photosmart M23 DD-20-DD-20S Star Mini F210A Photo 890 TMP241 FX-82solar DDX8017 Mixer IC-U68 DP522 DWL-520 BDP-S360HP IM-DR420H Fusion 2210 EY6220 HX270S JC-120 R-350 450A ASP 2 CK-100 Triton 400 P4350 Orbit 30048 NC4200 Hammerle 3P 750 ABS FAX-phone 1600 KDL-40EX708 Magicar 5 IC-M710
manuel d'instructions, Guide de l'utilisateur | Manual de instrucciones, Instrucciones de uso | Bedienungsanleitung, Bedienungsanleitung | Manual de Instruções, guia do usuário | инструкция | návod na použitie, Užívateľská príručka, návod k použití | bruksanvisningen | instrukcja, podręcznik użytkownika | kullanım kılavuzu, Kullanım | kézikönyv, használati útmutató | manuale di istruzioni, istruzioni d'uso | handleiding, gebruikershandleiding
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101