MR Series OM

7/28/98 10:32 AM

Page 1

MR SERIES LOUDSPEAKERS OWNERS MANUAL

S E R I E S

M5 MR25 MR26 MR28 MR38 MR308II MR310II MR Center

Page 2

INTRODUCTION
Congratulations on choosing JBL MR Series Loudspeakers. Their highly accurate, uncolored and balanced sound character will greatly increase your enjoyment of recorded music and movies. JBL speakers are built with careful attention to detail, using only the highest quality materials. They will provide many years of excellent performance. The MR Series is the result of combining traditional JBL Signature Sound performance values with elegant contemporary appearance. Maximum Radiating Surface Area: MR Series transducers utilize new transducer technology by extending the surface area of the cone allowing for a shorter excursion of the driver without sacrificing critical air movement. Maximum Efficiency: Larger air movement coupled with shorter coil movement allows the MR transducers to be very efficient. See specifications. Maximum Transducer Control: Reduces distortion by tightening the control of driver excursion and increasing driver linearity. Smooth, Accurate, Extended Response: The MR series transducers, computer-optimized dividing networks, and bass reflex cabinets combine to give clear, crisp, accurate, JBL Signature Sound.
between them, at the listening position, is between 40 and 60 degrees (see Fig. 1). For example, if your listening position is 8 to 12 feet (2.5m to 4m) from each speaker, the two systems should be about 8 feet (2.5m) apart. Placing the loudspeakers in corners or against a wall will result in the strongest (not necessarily the most accurate) bass. Except for the M5, all MR Series speakers have their ports in the front so you can place the rear of the speaker up against a wall. In the case of the M5, do not place the speaker closer than 3 inches (75mm) to the wall behind it if possible. For the best stereo imaging, we recommend that the systems be placed so that the high frequency transducers are positioned approximately at ear level of a seated listener. Every room is different and there are different tastes, so dont hesitate to experiment on your own.

Fig. 1

PLACEMENT
Bookshelf Models: For the best stereo reproduction, the two loudspeaker systems should be an equal distance from your listening position and separated so that the angle
Tower Models: The Tower models cabinet height and driver placement allow for speaker placement directly on the floor. For the best stereo reproduction, the two loudspeaker systems should be an equal distance from your listening position and separated so that the angle between

Page 3

MR SERIES LOUDSPEAKERS
them, at the listening position, is between 40 and 60 degrees. For example, if your listening position is 8 to 12 feet (2.5m to 4m) from each speaker, the two systems should be about 8 feet (2.5m) apart. Center Channel Model: As the center channel contains the dialog and other central action sounds, the speaker should be located very close to the Monitor/TV and centered with the Monitor/TVs center line. Place the MR Center directly on top of or directly below the Monitor/TV with the front edge of the speaker grille flush with the edge of the Monitor/TV. You should have your Left and Right speakers within a 2 ft or less height range of your Center Channel for proper sonic performance (see Fig 2). In Case Color Interference Occurs: The speaker is shielded to work with video applications, however some color interference may be observed on the TV screen depending on the type of your TV set. If color interference is observed, turn your TV off for 15 minutes and move the speaker back about 1" from the front edge of the TV. Turn on TV and recheck. If this is not far enough, move back further and experiment until the interference disappears. You may have to turn the TV off for a few minutes and turn it on again to clear the screen.

(2 ft. or less) (2 ft. or less)

CONNECTIONS

To connect the loudspeaker systems to the receiver or amplifier, use twoconductor insulated wire. Your JBL dealer can recommend suitable cables, or you can buy wire at most hardware or electronic stores. We recommend #16 AWG wire as a minimum size. If your speaker is more than 30 feet (10m) from your receiver or amplifier, use larger diameter lower gauge wire. Connections are made at the terminals located on the back of the MR Series speakers.
Preparing the Hookup Wire
Carefully plan your wire lengths before cutting any speaker wire. Be sure to allow plenty of extra wire to help hide paths in corners, along baseboards, etc.
1. For Left and Right Speakers, first determine the wire length needed between the most distant speaker and the receiver or amplifier. 2. Now make the hookup wires for both speakers this length, even if one loudspeaker is much closer to your amplifier than the other. This will help maintain proper signal balance. (For the MR Center, determine the length needed from AV receivers center channel output to speaker). 3. Strip off 38" of insulation from both ends of each conductor. 4. Twist each set of thin wires into a tightly-bunched spiral. 5. At this point you need to identify a visual difference between the two conductors of each molded pair of speaker wire. Differentiating marks can be a different color wire (copper or silver); a strand of yarn in one conductor; thin, raised ribs on one

Fig. 2

Page 4
part of the outer insulation; or a printed + marking on one of the insulators. It does not make any difference which of the two strands of wire go to (+) and () on the speakers and amplifier, as long as all speakers used in your system are connected identically. Push down on the button below the terminal and insert the wire through the hole. For each channel, the red terminal on all loudspeakers should be connected to the red or (+) speaker connection terminal on the receiver or amplifier, and the black to black or () speaker connection terminal (see Fig. 3). Connecting the loudspeakers in this manner ensures that they will be in phase; that is, work together rather than in opposition. This is very important when connecting several speakers together in a Dolby Pro-Logic AV application. Connecting the loudspeakers out of phase will not damage them, but will result in less bass and poor imaging.

AV receiver will enable you to correctly balance the level (volume) of sound coming from each speaker in your Dolby Pro-Logic application. Hooking Up Multiple Sets of Speakers If your receiver has two complete sets of speaker terminals (A and B), its possible to hook up an additional pair of speakers for simultaneous sound in another room. However, some speakers may not be usable as a second pair if you want to play two sets at once. Before hooking up another set of speakers besides your MR Series loudspeakers, check the following: 1. Your amplifiers minimum load impedance. 2. The nominal impedance of the second set of speakers. Both of these specifications are expressed in ohms and both can be found in the owners manuals which came with your speakers and amp/receiver. The receivers minimum load impedance is determined by whether or not power ratings are given for 4 ohms. This is because two sets of 8 ohm speakers will present a 4 ohm load to the receiver. The MR speaker, when combined with an 8 ohm speaker, produces an impedance sufficiently close to 4 ohms. For example, the following entry in an amplifier owners manual.
POWER: A)100 watts RMS into 8 ohms, both channels driven, 20-20kHz with less than 0.02%THD B) 160 watts RMS into 4 ohms, both channels driven, 20-20kHz with less than 0.02% THD.

Left Speaker

Red Blk. (+) ()

Right Speaker

Fig. 3
+ L + R Amplifier/Receiver
When connecting the MR Center or other MR Series speakers to a Dolby Pro-Logic AV receiver, refer to the instructions accompanying your AV component for use of the test tone to properly balance the sound output from each speaker. The use of the test tone and the controls on your
Part B indicates that the amplifier can handle 4-ohm combined impedances created by two sets of speakers.

Page 5

If only an 8-ohm rating is given, the amp/receiver may or may not be designed to handle 4-ohm combined ratings. Consult the owners manual of the amp/receiver for clarification. 2. Wrong speaker switch, A or B speaker output. 3. Sound source (CD,cassette deck, turntable) not turned on, not activated, not hooked up or not selected on amp/receiver front panel.

POWER HANDLING

Thanks to their high efficiency, the JBL MR Series Loudspeakers will produce reasonable volume levels in a room of moderate size with very little amplifier power. However, using a small amplifier to obtain the desired volume listening levels may lead to overdriving the amplifier. This will generate high distortion levels and may cause damage to your loudspeaker. For the best performance, an amplifier should be selected with an output rating that is greater than the maximum power that will be used. This margin of reserve power will ensure that the amplifier will not attempt to deliver more power than its design allows. However, the amplifiers power rating per channel must not exceed the maximum recommended amplifier power for that specific loudspeaker model. Please see the specification section for details. Following these guidelines will provide virtually distortion-free sound reproduction and long loudspeaker life.

No sound from one speaker 1. Balance control turned all the way left or right.
2. Speaker wire has become disconnected. 3. One of the connections between sound source and amp/receiver is faulty or has become disconnected.
Both speakers play at low volumes but shut off as volume is increased OR sound turns on and off intermittently A few strands of speaker wire may be shorting out. Recheck the connections. Recheck the impedance of the amp. Bass is very weak AND/OR sound seems to come from each speaker separately, without creating a stable stereo image between the speakers.
1. The polarity (+ & ) of one speaker has been reversed relative to the other. Double check connections. 2. Speakers are too far away from back and side walls or too far apart. Experiment again with the speaker placement. If you are still encountering problems, consult your JBL dealer. Additional Areas to Check When Using an AV Receiver: No sound at all or very faint sound from the center channel or other speakers 1. Speaker wire has become disconnected.

TROUBLESHOOTING

The vast majority of new speaker malfunctions end up being traced to connections or switch settings. To avoid packing up correctly functioning speakers and sending them off, only to find that theyre not really at fault, check the following tips first, before requesting service.
No sound at all or very faint sound from both speakers 1. Amp/receiver tape monitor button pushed in while using CD, FM or phono inputs.

Page 6

2. One of the connections between sound source and AV receiver/amp is faulty or has become disconnected. 3. AV receiver/amp center channel mode not selected. Please select a mode that activates the center channel. 4. Rear/surround information may not be recorded in some scenes and passages. 5. AV receiver/amp audio direct switch is activated. This switch should be off to activate the 5 speaker surround mode. 6. Sound source (VDP, VCR, CD, cassette deck, turntable) not turned on, not activated, not hooked up or not selected on AV receiver/amp front panel.

SERVICE

Should your loudspeaker ever need service, return it to the JBL dealer from whom it was purchased. If purchased outside the United States, contact your local distributor to make arrangements for repair service. Do not return products to the JBL factory without prior authorization.

GENERAL CARE

The grille is held in place by pins near the edges. To remove the grille, grasp it by both top and bottom edges and pull gently. To replace grille, re-position it carefully and press gently at the corners. Do not push on the center area of the grille.

NOTE: The M5 grille is nonremovable. Do not attempt to pry the grille from the cabinet as this will void your warranty. The rear panels are removable to allow service personnel access to the driver components if needed.
The loudspeaker cabinet may be cleaned with a slightly damp cloth. To remove dust from the grille cloth, use a vacuum with a brush attachment. Spots may be removed with a commercial spot remover. Do not use any cleaners or solvents on the speaker drivers themselves.

Page 7

Specifications

Application

MR Center
Center Channel 10mm Ti Composite n/a

Bookshelf

High Frequency Dome Transducer Midrange Transducer (Nitrile Polymer Fibre Cone) Low Frequency Transducer (Nitrile Polymer Fibre Cone) Crossover Frequency Frequency Response ( 6 dB) Sensitivity (1 Watt/1 Meter) Nominal Impedance Recommended Amplifier Power* External Dimensions Height Width Depth External Dimensions Height Width Depth Weight (each) Shipping Weight

2" Paper (Cone) n/a

10mm Ti Composite n/a 5" 4.5kHz 70 Hz to 20 kHz 87 dB 8 ohms 10 to 75 Watts 12" 712" 812" 305 mm 190 mm 216 mm 8 lbs 3.6 kg 20 lbs 9.1 kg
10mm Ti Composite n/a 612" 4.5kHz 55 Hz to 20 kHz 88 dB 8 ohms 10 to 100 Watts 15" 812" 10" 381 mm 216 mm 254 mm 12 lbs 5.5 kg 28 lbs 12.7 kg
2 x 3.5" 5" (Neo Magnet) 4.5kHz 80 Hz to 20 kHz 87 dB 8 ohms 10 to 80 Watts 5316" 1414" 658" 132 mm 362 mm 168 mm 7 lbs 3.2 kg 10 lbs 4.5 kg 2.2kHz 75 Hz to 20 kHz 86 dB 8 ohms 10 to 50 Watts 11" 612" 714" 280 mm 165 mm 184 mm 7 lbs 3.2 kg 18 lbs 8.2 kg
*The maximum recommended amplifier power rating will insure proper system headroom to allow for occasional program peaks. We do not recommend sustained operation at these maximum power Levels.

Page 8

Application High Frequency 14mm" Ti Dome Transducer Midrange Transducer (Nitrile Polymer Fibre Cone) Low Frequency Transducer (Nitrile Polymer Fibre Cone) Crossover Frequency Frequency Response ( 6 dB) Sensitivity (1 Watt/1 Meter) Nominal Impedance Recommended Amplifier Power* External Dimensions Height Width Depth External Dimensions Height Width Depth Weight (each) Shipping Weight
Bookshelf 14mm Ti Composite n/a 8" 3.5kHz 50 Hz to 20 kHz 90 dB 8 ohms 10 to 125 Watts 1914" 10" 10" 489 mm 254 mm 254 mm 18 lbs 8.2 kg 40 lbs 18.2 kg
Bookshelf 14mm Ti Composite 612" 8" 3.5kHz 45 Hz to 20 kHz 92 dB 8 ohms 10 to 150 Watts 24" 10" 12" 610 mm 254 mm 305 mm 25 lbs 11.3 kg 29 lbs 13.2 kg

MR308II

Tower 14mm Ti Composite 612" 8" 3.5kHz 42 Hz to 20 kHz 92 dB 8 ohms 10 to 150 Watts 32316" 10" 12" 818mm 254 mm 305 mm 28 lbs 12.7 kg 32 lbs 14.5 kg

MR310II

Tower 14mm Ti Composite 612" 10" 3.5kHz 40 Hz to 20 kHz 92 dB 8 ohms 10 to 175 Watts 36" 1134" 12" 915 mm 298 mm 305 mm 32 lbs 14.5 kg 36 lbs 16.4 kg
JBL continually strives to improve its products. New materials, production methods and design refinements are introduced into existing models without notice as a routine expression of our design philosophy. For this reason, JBL MR Series Loudspeakers may differ in some respect from their published specifications and descriptions, but will always equal or exceed the original specifications unless otherwise stated.
250 Crossways Park Drive, Woodbury, NY Balboa Blvd., Northridge, CA 91329 Part No. 332408-001 A Harman International Company Printed in Taiwan

home | pay | register | sign out | site map

Start new search

Search Advanced Search

Back to list of items

Listed in category:
Consumer Electronics > Home Audio > Speakers & Subwoofers > Bookshelf Speakers > Polk Speakers
Polk Monitor 5 Speakers Great Sound
Bidding has ended for this item
If you are a winner, Sign In for your status. List an item like this or buy a similar item below.
Item number: 5825028450 Email to a friend

Sold for:

US $95.00 (Reserve met) Auction ended early with Buy It Now.
Ended: Start time: History: Buyer: Larger Picture Item location: Ships to:
Nov-06-05 11:12:13 PST Oct-30-05 19:49:48 PST 7 bids (US $9.95 starting bid)
Marietta, Georgia United States United States, Canada, United Kingdom, Japan
Shipping costs: Calculate shipping costs Shipping, payment details and return policy

Special Holiday Offer

Make no payments for 3 to 12 months with PayPal Buyer Credit. Good until 12/31/05. Promotional term based on minimum purchase. See details | Apply now

Description

Item Specifics - Home Speakers Speaker Type: Bookshelf Brand: Wireless: -Condition: Used
Polk Cabinet Color: Wood - Dark
I recently bought the inventory of a stereo store that went out of business years ago and everything has been in storage since. You wont believe the great sound that comes out of these modest sized boxes. They are truly a bookshelf speaker that can fill the room with sound. The 8 Passive woofer provides ample bass at low volumes too. All of the drivers work great and the only missing item for these speakers is that I could not find the grills anywhere in the inventory. You will not be disappointed once you fire them up! Dont be outbid at the last minute by $1.00 or miss the auction closing time because you forgot! Use the Buy It Now option and own it today for a fair price! I prefer Paypal but accept bidpay, Western Union and a Money Order. Buyer pays actual shipping and $7.50 for the box and packing materials. Also I travel a lot in my job and I do not always have e-mail available, so from time to time I may take a few days to respond to your questions or to ship your item. I tend to over-pack so I will guarantee that my packing will meet the requirements of the carrier so that insurance will cover the damage should there be a claim.
Powered by eBay Turbo Lister Select a picture
FREE Counters and Services from Andale

Save on shipping -

buy additional items now from this seller's other listings!
Mitsubishi MGA DA-U300 Amp & DA F200 Tuner US $120.00
Teac TN-400 Magnefloat Turntable WOW US $195.00
Sansui 7070 Receiver Volts -Just Serviced! LO US $102.50
JBL MR-28 Two Way Speakers - Great Sound! US $95.00
View this seller's other items
Shipping, payment details and return policy
Services Available UPS Ground USPS Economy Parcel Post Available to United States Only Canada, United Kingdom, Japan

Calculate shipping

Enter your US ZIP Code:

Calculate

Will ship to United States, Canada, United Kingdom, Japan. Save on shipping - buy additional items now from this seller's other listings! Shipping insurance Optional
click Calculate or select an international destination Learn more about how calculated shipping works.

Payment methods accepted

Money order/Cashiers check Learn about payment methods. Where to go next? Back to list of items | Printer Version | Safe Trading Tips Seller assumes all responsibility for listing this item.
eBay Pulse | eBay Reviews | eBay Stores | Half.com | Kijiji | PayPal | Popular Searches | ProStores | Rent.com | Shopping.com Australia | Austria | Belgium | China | France | Germany | India | Italy | Spain | United Kingdom About eBay | Announcements | Security Center | Policies | Site Map | Help
Copyright 1995-2005 eBay Inc. All Rights Reserved. Designated trademarks and brands are the property of their respective owners. Use of this Web site constitutes acceptance of the eBay User Agreement and Privacy Policy.