Power Series OM

6/11/99

11:13 AM

Page 1

Power Series Amplifiers

P80.2, P180.2, P80.4, BP150.1, BP300.1, BP600.1, BP1200.1 Owners Manual GENUINE JBL

Page 2

Thank you for purchasing a JBL Power Series amplifier. In order that we may better serve you should you require warranty service for your new amplifier, please retain your original purchase receipt and return the enclosed warranty registration card. Warning: Playing loud music in an automobile can permanently damage your hearing as well as hinder your ability to hear traffic. We recommend listening at low levels while driving your car. JBL accepts no liability for hearing loss, bodily injury or property damage resulting from use or misuse of this product. Important: Installation of automotive stereo components can require extensive experience in performing a variety of mechanical and electrical procedures. Although these instructions explain, in a general sense, how to install Power Series amplifiers, they may not show the exact installation methods for your particular vehicle. If you feel you lack the necessary tools or experience, ask your authorized JBL car-audio dealer about professional installation options.
Choosing a Location and Mounting the Amplifier
Amplifiers need air to stay cool. Suitable locations are under a seat (provided the amplifier doesnt interfere with the seat adjustment mechanism), in the trunk or in any other location which provides enough air for the amp to cool itself. Do not mount the amplifier with the heat sink facing downward, as this makes convection cooling of the amplifier impossible. Mount the amplifier so that it is not damaged by the feet of back-seat passengers or shifting cargo in the trunk. Mount the amplifier so that it remains dry never mount an amplifier outside the car or in the engine compartment. Using the amplifier as a template, mark the location of the mounting holes on the mounting surface, drill pilot holes, and attach the amplifier to the mounting surface with screws. Make sure the amplifier is mounted securely.
Installation Warnings and Tips
Always wear protective eyewear when using tools. Turn off all audio systems and other electrical devices before you start. Disconnect the () negative lead from your vehicles battery. Check clearances on both sides of a planned mounting surface before drilling any holes or installing any screws. Remember that the screws can extend behind the surface. At the installation sites, locate and make a note of all fuel lines, hydraulic brake lines, vacuum lines and electrical wiring. Use extreme caution when cutting or drilling in and around these areas.
Before drilling or cutting holes, use a utility knife to remove unwanted fabric or vinyl to keep material from snagging in a drill bit. When routing cables, keep input-signal cables away from power cables and speaker wires. When making connections, make certain they are secure and properly insulated. If the amplifiers fuse must be replaced, use only the same type and rating as that of the original. Do not substitute another kind.

Page 3

BP150.1, BP300.1, BP600.1, BP1200.1

FUSES 40A x 3

P80.2, P180.2

FUSES 20A x 2

+ BATT REM POWER GND

SPEAKER OUTPUTS

BRIDGED SPEAKER OUTPUTS

REM POWER

INPUT LEVEL

LPF FREQ

BASS BOOST

+ R L +

INPUT MODE
X-OVER FLAT HP LP 32Hz320Hz FREQ

L+ L L

4V 250mV 32Hz 320Hz 0dB +6dB

HIGH LEVEL FRONT INPUTS

HIGH LEVEL REAR INPUTS

HIGH LEVEL L INPUTS

4V 250mV
Note: Drawing is provided only for connector, control and fuse location. Please see Specifications for fuse requirements.

Figure 1

Figure 2

X-OVER

FLAT HP LP

ST MD ST MD

HIGH LEVEL
4V 250mV 32Hz 320Hz 32Hz 320Hz 4V 250mV

REAR +BATT REM POWER GND

BRIDGED

Figure 3

Page 4

FREQUENCY

Crossover Wiring the Power Connections
Refer to Figures 13 for connector locations. All the Power Series amplifiers will accept up to 4-gauge power and ground wire. For power, remote and ground connections, strip off one end of each jacket to reveal bare wire for insertion into the connectors. Connect a wire from the GND connector on the amplifier to the nearest bare-metal chassis component; scrape away the paint to ensure good conductivity. Next, connect a wire between the BATT terminal on the amplifier and the POS(+) terminal of the vehicles battery. Pass the wire through a factory-installed grommet in the firewall, or install a grommet if a factory grommet is not available. Connect a wire between the REM terminal of the amplifier and the remote out or powerantenna lead on the vehicles radio.

INDUCTOR

6dB/oct. LP (4-ohm) 8.0mH 6.4mH 5.0mH 4.2mH 3.6mH 3.2mH

CAPACITOR

6dB/oct. HP (4-ohm) 530F 400F 318F 265F 227F 198F
Wiring the Speaker-Output Connections
P80.2, P180.2, P80.4 All the Power Series amplifiers will accept up to 8-gauge speaker wire. Connect the speakers, observing proper polarity, to the speaker-output connector. The total impedance of the speaker system connected to the amplifier when the amplifier is driven in stereo must be at least two ohms. If you are bridging the amplifier, connect the speaker wires to the terminals marked bridged, observing proper polarity. The total impedance of the speaker system connected to the amplifier must be at least four ohms in bridged mode.
75Hz 100Hz 125Hz 150Hz 175Hz 200Hz
If you are running the amp in Tri-Mode (stereo and mono simultaneously), connect the satellite speakers to the speaker connector as you would a pair of stereo speakers. Connect the subwoofer to the terminals marked bridged Refer to the chart above to determine the capacitor and inductor values youll need to route bass signals to the woofer, and the midrange and high frequencies to the satellite speakers. These passive crossover components will also ensure that the impedance of the speaker system doesnt drop below two ohms.
BP150.1, BP300.1, BP600.1, BP1200.1 Connect the woofers to the amplifier, observing proper polarity. Although these amplifiers have a single channel, duplicate positive and negative connectors are provided to facilitate the connection of multiple woofers. The total impedance of the speaker system connected to a BP Series amplifier must be at least 1 ohm.

Page 5

Wiring the Input-Signal Connections
Connect a pair of signal cables with RCA-type ends between the connectors on the amplifier and the RCA-type signal connectors on the source unit. If your radio has only speaker-level outputs, you should connect them to the speaker-level input connectors, observing proper polarity. When using the speaker-level inputs, it is not necessary to connect a wire between the remote terminal of the amplifier and the remote lead from the source unit. The speaker-level inputs will sense voltage on the speaker outputs and turn the amplifier on automatically. If you are installing a P80.4 amplifier and your source unit has only one pair of RCA-type output connectors and a pair of speaker-level outputs, you may connect the RCA outputs to a pair of amplifier input channels (front or rear), and the speaker-level outputs to the other pair of amplifier input channels.

Setting Input Level

The BP150.1, BP300.1, BP600.1 and BP1200.1 are designed to provide constant bass regardless of the position of the source units front-to-rear fader position. Use of this feature requires that all four inputs are connected to the source unit as labeled on the amplifier (front, rear, right and left). If your source unit has only one pair of RCA-type output connectors and a pair of speaker-level outputs, you may connect the RCA outputs to a pair of amplifier input channels (front or rear), and the speaker level outputs to the other pair of amplifier input channels. If nonfading bass is not important in your system, connect a pair of inputs, either speaker-level or RCA-type, to either the front or rear input connectors on the amplifier.

System Setup and Adjustment
Refer to figures 16 for location of adjustment switches and controls. Electronic Crossover and Bass Boost P80.2, P80.4, P180.2 The electronic crossover can be selected as a 12dB/oct. high-pass filter (HPF) 12dB/oct. low-pass filter (LPF) or it can be defeated (FLAT). The crossover frequency can be set at any frequency between 32Hz and 320Hz. BP150.1, BP300.1, BP600.1, BP1200.1 These amplifiers are designed to drive subwoofers. Consequently, the electronic crossover is a 12dB/oct. low-pass filter which can be set at any frequency between 32Hz and 320Hz. The bass boost control will provide up to 6dB of boost at 50Hz.
Initially, turn the input-sensitivity LEVEL control to its maximum (counter-clockwise) position. Turn on the source unit and increase the volume control until it is approximately three-quarters of maximum-output level. Slowly increase the input LEVEL control (clockwise) while listening to the quality of the reproduced sound. When you hear distortion on the music peaks, turn the LEVEL control back slightly. This is the maximum undistorted output level of your system. Turning the LEVEL control up farther WILL NOT INCREASE THE OUTPUT POWER OF YOUR AMPLIFIER! It will only decrease the amount of volumecontrol rotation before the amp is at fulloutput power. It will also increase the amount of extraneous noise present in your system.

Page 6

Troubleshooting
Symptom No Audio (Red LED flashes every four seconds) Likely Cause Short circuit in speaker or speaker wire. Solution Disconnect speaker leads one at a time to determine which speaker or wire is shorted or defective. Repair the short circuit or replace bad speaker. Check voltage at amplifier terminals with VOM.
No Audio (Power indicator is off) No Audio (Green power LED is lit) No Audio (Red LED stays lit) Distorted Audio
No voltage at BATT or REM terminals. Bad or no ground connection. Amplifier overheated.
Make sure amplifier cooling isnt prevented by mounting location, make sure speaker-system impedance is within limit (see Specifications). Check vehicle charging system for defective voltage regulator.
Excessive voltage on B (+) connection.

Input sensitivity not set properly; amplifier or source unit defective. Speakers are not connected properly.

Check LEVEL setting.

Music lacks punch
Check speaker connections for proper polarity.

Page 7

Specifications
P80.2, P180.2, P80.4, BP150.1, BP300.1, BP600.1, BP1200.1
Specifications Power Output, 4 ohms Power Output, 2 ohms Power Output, 4 ohms Bridged Minimum speaker impedance Frequency Response Input Sensitivity (RCA type) THD + Noise (4 ohms) Signal-to-Noise Maximum Current Draw Fuse Requirement Dimensions (H x W x L) P80.2 40W x 2 80W x 2 160W x ohms 10Hz 50kHz 250mV ~ 4V 0.05% >100dB 24 amps 20A 8-3/4 x 8 x 2-11/16" 222 x 205 x 67.5mm P180.2 90W x 2 180W x 2 360W x ohms 10Hz 50kHz 250mV ~ 4V 0.05% >100dB 45 amps 20A x 2 9-1/16 x 12-9/16 x 2-11/16" 229 x 319 x 67.5mm P80.4 40W x 4 80W x 4 160W x ohms 10Hz 50kHz 250mV 4V 0.05% >100dB 43 amps 20A x 2 9-1/16 x 12-9/16 x 2-11/16" 229 x 319 x 67.5mm BP150.1 75W 150W NA 1 ohm* 10Hz 320Hz 250mV 4V 0.10% >90dB 14 amps 20A 8-3/4 x 8 x 2-11/16" 222 x 205 x 67.5mm BP300.1 150W 300W NA 1 ohm* 10Hz 320Hz 250mV 4V 0.10% >90dB 29 amps 20A x 2 8-5/16 x 10-3/4 x 2-11/16" 210 x 273 x 67.5mm BP600.1 300W 600W NA 1 ohm* 10Hz 320Hz 250mV 4V 0.10% >90dB 57 amps 30A x 2 9-1/16 x 12-9/16 x 2-11/16" 229 x 319 x 67.5mm BP1200.1 600W 1200W NA 1 ohm* 10Hz 320Hz 250mV 4V 0.10% >90dB 114 amps 40A x 3 10-13/16 x 14-13/16 x 2-11/16" 274 x 376 x 67.5mm
* No increase in output power over 2 rating.

Page 8

Declaration of Conformity
We, JBL Europe A/S Kongevejen 194B DK-3460 Birkerd DENMARK
declare in own responsibility, that the products described in this owners manual are in compliance with technical standards: EN 55013/A12/8.1994 EN 55020/12.1994
Steen Michaelsen JBL Europe A/S Birkerd. DENMARK. 4/99
JBL Consumer Products 250 Crossways Park Drive, Woodbury, NY Balboa Boulevard, Northridge, CA 91329 1-800-336-4JBL (4525) (USA only) www.jbl.com 1999 JBL, Incorporated JBL is a registered trademark of JBL, Incorporated. Part No. PSAMPOM 4/99

Subwoofrid (tkk) 1000GTI 1200GTI CS10 CS12 GT2-12 GT3-12 GT4-15 P-1000 P-1200 P-1500 P1020E LC-S1050W LC-S1250W T120 T150 Vimendid (tkk) BP300.1 DA1002 DA3504 DA4002 GTO6000 GTO755.6 GTQ240E GTQ360E LC-A504 P180.2 P80.2 P80.4 PX300.4 PX600.2 Klarid (paar) C620 CS308E CS3108 CS3196 CS396E GT4.0C GT5.0C MKII GT6.0C MKII GTO16TE GTO202 MKII GTO4 GTO4 MKII GTO4.2C GTO422 GTO5.2C GTO502 MKII GTO506CE GTO526E GTO606CE JBL 6.5"automotive 2-way JBL 8" 3-way 200mm JBL 20cm 3way speaker JBL 6x9 3way speaker JBL 6x9"160mmX230mm JBL 2-way 4" comp.Car sp JBL 2-way 5 1/4"comp.car JBL 2-way 6"Compon.Car JBL tweeter 25mm JBL 2+" 2-way car speake JBL 1"tit comp dome neo JBL 1"tit comp dome neo JBL 4" 2-way component JBL 4" 2-way Car Speaker JBL 5.25"2-way comp.car JBL 5.25" 2-way car spea JBL 130mm 2-way car spea JBL 2-way 130mm JBL 6"2-way car speaker 2tk 1tk 3tk 7tk 5tk 1tk 26tk 21tk 6tk 3tk 1tk 2tk 1tk 2tk 3tk 1tk 3tk 3tk 1tk 3533.1454.1251.1158.1283.1698.1943.2042.812.1246.946.946.1743.1600.3240.1146.1992.1065.2084.JBL 150x1W car amplifier JBL Car Amplifier 2CHx10 JBL car amplifier 4CHx50 JBL Car Amplifier 2CHx40 JBL 6chanel JBL Car 6ch.amplifier JBL car amplifier 4CHx40 JBL 60W/4ch car amplifie JBL 4x50W car amplifier JBL 90x2W Car Amplifier JBL 2x40W Car amplifier JBL 4x40W Car Amplifier JBL 300W 4-ch. JBL 600W 2-ch.car 1tk 4tk 2tk 2tk 2tk 4tk 1tk 2tk 2tk 2tk 2tk 4tk 2tk 1tk 5048.5331.4359.3089.5047.5790.6388.6509.3886.4982.3488.5730.9263.9263.JBL 10" Subwoofer 250mm JBL 12" Subwoofer 300mm JBL 10'' Subwoofer 250mm JBL 12'' Subwoofer 300mm JBL 12" Subwoofer 300mm JBL 12" Subwoofer 300mm JBL 15'' Subwoofer 380mm JBL 10" Subwoofer 250mm JBL 12" Subwoofer 300mm JBL 15" Subwoofer 380mm JBL 10" Subwoofer 250mm JBL 10" Subwoofer 250mm JBL 12" Subwoofer 300mm JBL 12" Subwoofer 300mm JBL 15" Subwoofer 380mm Laoseis 5tk 8tk 3tk 8tk 1tk 1tk 1tk 1tk 2tk 1tk 3tk 2tk 1tk 4tk 1tk mgihind 4727.5507.834.926.1881.1600.1860.2249.3208.2700.3208.1246.1285.2242.2740.-
GTO6537 GTO75.2 GTO75.4 GTO8627 GTO923 GTO926E GTO937 GTR10 GTX425
JBL 3way 16,5cm speaker JBL car speaker JBL Car speaker JBL 6"x8" 2-way speaker JBL car speaker JBL 6x9"2-way JBL 3way 6x9" speaker JBL 10mm Tweeter JBL 2-way 4"component ca
3tk 1tk 1tk 4tk 1tk 6tk 3tk 1tk 3tk
1204.3150.4168.1065.1879.1369.1389.448.2818.-
T030 JBL 3" Midrange Driver 7tk 1495.Power Handling, RMS 200 watts Nominal Impedance 4 ohms Midrange Driver 3" pure titanium dome Frequency Response 500Hz - 8kHz Sensitivity 92dB (1 watt/1 meter) Mounting Depth 2" Hole Size Required 5" Vimendatud subwoofer BASS-PRO II JBL Amplified Subwoofer 2tk 2779.-

Infinity

Subwoofrid (tkk) BETA 12X BETA 15X 12" Subwoofer 300mm 15" Subwoofer 380mm 10" Subwoofer 250mm 12" Subwoofer 300mm
Laoseis 3tk 2tk 1tk 1tk 2tk 1tk
mgihind 4130.5736.2092.2541.4261.2491.-
DIAMETER: 12" (304.8 MM), SENSITIVITY (2.83 V @ 1 M): 94 dB, POWER HANDLING: 275 WRMS, FREQUENCY RESPONSE: 20 ~ 400 HZ, NOMINAL IMPEDANCE: 4 OHMS, VOICE-COIL DIAMETER: 2.0" (50.65 MM). DIAMETER: 15" (381.0 MM), SENSITIVITY (2.83 V @ 1 M): 97 dB, POWER HANDLING: 350 WRMS, FREQUENCY RESPONSE: 18 ~ 350 HZ, NOMINAL IMPEDANCE: 4 OHMS, VOICE-COIL DIAMETER: 3.18" (80.8 MM).
KAPPA 100.3SE KAPPA 120.1SE
DIAMETER: 10" (254.0 MM), SENSITIVITY (2.83 V @ 1 M): 90 dB, POWER HANDLING: 275 WRMS (1,100 WPEAK), FREQUENCY RESPONSE: 20 ~ 250 HZ, NOMINAL IMPEDANCE: 4 OHMS, VOICE-COIL DIAMETER: 2.0" (50.0 MM). DIAMETER: 12" (304.8 MM), SENSITIVITY (2.83 V @ 1 M): 94 dB, POWER HANDLING: 300 WRMS, FREQUENCY RESPONSE: 20 ~ 250 HZ, NOMINAL IMPEDANCE: 4 OHMS, VOICE-COIL DIAMETER: 2.0" (50.0 MM).
KAPPA PERFECT10.1 REF 1220W
10" Subwoofer 250mm 12" Subwoofer 300mm
DIAMETER: 10" (254.0 MM), SENSITIVITY (2.83 V @ 1 M): 94 dB (IN-CAR @ 40 HZ), POWER HANDLING: 350 WRMS (1,400 WPEAK ), FREQUENCY RESPONSE: 18 ~ 150 HZ, NOMINAL IMPEDANCE: 4 OHMS, VOICE-COIL DIAMETER: 2.0" (50.8 MM) DIAMETER: 12" (304.8 MM), SENSITIVITY (2.83 V @ 1 M): 92 dB, POWER HANDLING: 300 WRMS, FREQUENCY RESPONSE: 20 ~ 800 HZ, NOMINAL IMPEDANCE: 4 OHMS, VOICE-COIL DIAMETER: 2.0" (50.0 MM).
Vimendid (tkk) KAPPA 102A 2 x 100 watts amplifier 1tk 7000.Power Output, 4 ohms: 2 x 100 watts, Power Output, 2 ohms: 2 x 150 watts, Power Output Bridged 4 ohms: 300 watts, Frequency Response: 20 Hz ~ 20 kHz, Input Sensitivity: 250 mV ~ 9 V, THD + Noise (4 ohms): 0.05 % Signal-to-Noise: > 95 dB, Maximum Current Draw: 40 A.

KAPPA 52A

2 x 50 watts amplifier

4943.-

Power Output, 4 ohms: 2 x 50 watts, Power Output, 2 ohms: 2 x 75 watts, Power Output Bridged 4 ohms: 150 watts, Frequency Response: 20 Hz ~ 20 kHz, Input Sensitivity: 250 mV ~ 9 V, THD + Noise (4 ohms): 0.05 %, Signal-to-Noise: > 95 dB, Maximum Current Draw: 20 A.

RA7502

2x110 watts amplifier

3705.-

Channels 2, Power Output max 300W, RMS Bridged Power Output 4 ohms:220W, RMS Power Output, 2 ohms: 2 x 110W, RMS Power Output, 4 ohms:2 x 75W, THD@Rated Output 0.10%, SNR (A weighted) >92dB, Frequency response 10Hz-40kHz, Active crossover(cont.var.) 30-320Hz, Crossover settings LP/HP/OFF, Crossover slope 12dB/oct, Input sensitivity 100mV-4V, Bass Boost +6dB@45Hz.
Vred (paar) BETA 4-GRILLE BETA 5-GRILLE BETA 6-GRILLE Filtrid (tkk) BETA XP ONE
crossover frequency 1.5kHz
grille for Beta grille for Beta grille for Beta

5tk 7tk 6tk

92.138.181.-
passive crossover passive crossover

12tk 3tk

2527.2450.-

BETA XP TEN

crossover frequency 3.5kHz
Klarid (paar) BETA 5 KAPPA 10.3T 5-1/4'' (13mm) Midrange 1" tweeter 5tk 2tk 2522.1246.POWER HANDLING: 120W,SENSITIVITY (2.83 V @ 1 M): 89dB, FREQUENCY RESPONSE: 40 ~ 5,000 HZ, DIAMETER: 2.75" (7cm)
1" tweeter, Speaker Impedance: 4 ohms, Power Handling: 50W RMS, 150W Peak, (with enclosed crossover), Sensitivity (2.83V, 1m): 90dB, Frequency Response: 3.5kHz 21kHz, Mounting Depth: 1-3 16" (31mm), Cut-out Diameter: 1-7/8" (47mm).

KAPPA 10.5T

1" Tweeter
1343.2840.1205.1112.3836.-
1" tweeter, Speaker Impedance: 4 ohms, Power Handling: 50W RMS, 150W Peak, (with enclosed crossover), Sensitivity (2.83V, 1m): 90dB, Frequency Response: 3.5kHz 21kHz, Mounting Depth: 1-3 16" (31mm), Cut-out Diameter: 1-3/4" (45mm).

KAPPA EMIT

1'' Tweeter

1tk 2tk 6tk 2tk

component tweeter.
KAPPA Perfect T REF 1001T
1" Tweeter 1" tweeter
Frequency response: 3.5kHz 21kHz, 3dB, Power handling: 100W RMS, 400W Peak (with HPF provided), Nominal impedance: 4 Ohms, Sensitivity: 90dB, Crossover frequency: 3.5kHz, Voice-coil diameter: 1" (25.4mm), Mounting depth: 1-3/16" (31mm), Cut-out diameter: 1-3/4" (45mm). 1" Edge-driven textile-dome tweeter with I-Mount tweeter mounting system included.

KAPPA 40.1CS

2-Way System 4"
Speaker Impedance: 4 ohms, Power Handling: 90 watts per channel, Frequency Response (3dB): 80Hz ~ 20kHz, Sensitivity: 89Hz @ 2.83 V, 1 watt, Crossover Frequency: 8kHz, Mounting Depth, Drop-in Midrange: 1-13/16" (47 mm), Cut-out Diameter, Midrange: 3-3/4" (96 mm), Cut-out Diameter Tweeter: 1-5/8" (41 mm).

KAPPA 50.1CS

2-Way System 5-1/4"

3890.-

Speaker Impedance: 4 ohms, Power Handling: 100 watts per channel, Frequency Response (3dB): 59Hz ~ 20kHz, Sensitivity: 89Hz @ 2.83 V, 1 watt, Crossover Frequency: 8kHz, Mounting Depth, Drop-in: 2-3/8" (61 mm), Cut-out Diameter: 4-13/16" (123 mm), Cut-out Diameter Tweeter: 1-5/8" (41 mm).

KAPPA 60.1CS

2-Way System 6-1/2"

1tk 1tk

4084.3360.-
Speaker Impedance: 4 ohms, Power Handling: 120 watts per channel, Frequency Response (3dB): 50Hz ~ 20kHz, Sensitivity: 89Hz @ 2.83 V, 1 watt, Crossover Frequency: 8kHz, Mounting Depth, Drop-in: 2-7/16" (62 mm), Cut-out Diameter: 5-1/8" (131 mm), Cut-out Diameter Tweeter: 1-5/8" (41 mm).

KAPPA 652.1CS

2-Way System 166 mm
Speaker Impedance: 4 ohms, Power Handling: 120 watts per channel, Frequency Response (3dB): 50Hz ~ 20kHz, Sensitivity: 89Hz @ 2.83 V, 1 watt, Crossover Frequency: 8kHz, Mounting Depth, Drop-in: 2-1/2" (64 mm), Cut-out Diameter: 5-11/16" (145 mm), Cut-out Diameter Tweeter: 1-5/8" (41 mm).

KAPPA Perfect 6.1

2-way system 6,5"

5372.-

Tweeter + woofer, Frequency Response: 75Hz 23kHz, 3dB, Power Handling: 100W RMS, 400W Peak, Nominal Impedance: 4 Ohms, Sensitivity: 90dB, Crossover, Frequency: 3.5kHz, 24dB/oct., Linquitz-Riley Acoustic.
KAPPA 42.1 I KAPPA 52.1 I KAPPA 63.1 I
2-way 4" 2-way 5 1/4"

2tk 4tk 4tk 4tk 4tk

1744.1993.3288.3208.3986.-
Speaker Impedance: 4 ohms, Power Handling: 45W, Frequency Response: 80Hz ~ 20kHz, Sensitivity: 89Hz @ 2.83 V, 1 watt, Mounting Depth, Drop-in: 1-3/4" (45 mm), Cut-out Diameter: 3-3/4" (96 mm). Speaker Impedance: 4 ohms, Power Handling: 50W, Frequency Response: 59Hz ~ 20kHz, Sensitivity: 89Hz @ 2.83 V, 1 watt, Mounting Depth, Drop-in: 2-7/16" (62 mm), Cut-out Diameter: 4-13/16" (123 mm).
3-way 6-1/2'' 2-way 6x9" 3-way 6x9"
Speaker Impedance: 4 ohms, Power Handling: 70W, Frequency Response: 50Hz ~ 21kHz, Sensitivity: 89Hz @ 2.83 V, 1 watt, Mounting Depth, Drop-in: 2-7/16" (62 mm), Cut-out Diameter: 5-1/8" (131 mm).

KAPPA 692.1 I KAPPA 693.1 I
Speaker Impedance: 4 ohms, Power Handling: 100W, Frequency Response: 38Hz ~ 20kHz, Sensitivity: 89Hz @ 2.83 V, 1 watt, Mounting Depth, Drop-in: 2-3/4" (70 mm), Cut-out Diameter: 5-11/16" x 8-3/4", (145 mm x 223 mm). Speaker Impedance: 4 ohms, Power Handling: 100W, Frequency Response: 38Hz ~ 21kHz, Sensitivity: 89Hz @ 2.83 V, Mounting Depth, Drop-in: 2-3/4" (70 mm), Cut-out Diameter: 5-11/16" x 8-3/4", (145 mm x 223 mm).
KAPPA 572CF KAPPA 65.1MB KAPPA 80F
2-way 5x7" 6" Midrange 8" flat

2tk 1tk 1tk

2074.1893.3062.-
Power Handling: RMS 75 watts, Sensitivity 89dB (2.83V/1 meter), Frequency Response 70Hz 20kHz, Mounting Depth 2.125"
Speaker Impedance: 4 ohms, Power Handling: 100W, Frequency Response: 40Hz ~ 2.5kHz, Sensitivity: 89Hz @ 2.83 V, Mounting Depth, Drop-in: 27/16" (62 mm), Cut-out Diameter: 5-1/8" (131 mm). Sensitivity 90dB, 2.83V/1m, Frequency Response 40Hz -700kHz +/-3dB, Power Handling: RMS 125 watts, RMS w/included Crossover, Hole Size Required 7" (190mm) Depth 1.25".

REF 452 I

2-way 4"

1295.-

Speaker Impedance: 4 Ohms, Power Handling: 35W RMS, 105W Peak, Frequency Response: 90Hz 20kHz, Sensitivity: 92dB, Mounting Depth: 1-7/8" (48mm), Cut-out Diameter: 3-3/4" (96mm).

REF 5000CS

2-way system 130mm (5-1/4'')

2686.-

2-Way Component System, Speaker Impedance: 4 Ohms, Power Handling: 75W RMS, 225W Peak, Frequency Response: 67Hz 21kHz, Sensitivity (2.83V, 1m): 92dB, Crossover Frequency: 3.5kHz, Mounting Depth: Woofer: 2-1/4" (58mm), Tweeter: 1-1/4" (32mm), Cut-out Diameter: Woofer: 411/16" (120mm), Tweeter: 1-13/16" (47mm).

REF 500cs

1556.-
Power Handling: RMS 75 watts per channel, Sensitivity 90dB@2.83, Frequency Response 80Hz 20kHz, Mounting Depth 5.4cm Woofer and 2.2cm tweeter.

REF 510cs REF 6000CS

2-way system 130mm (5-1/4'') 2-way system 160mm 6-1/2"

2167.2825.-

Power Handling: RMS 75 watts per channel, Sensitivity 90dB@2.83, Frequency Response 80Hz 20kHz, Mounting Depth 5.4cm Woofer and 2.2cm tweeter. 2-Way Component System, Speaker Impedance: 4 Ohms, Power Handling: 90W RMS, 270W Peak, Frequency Response: 53Hz 21kHz, Sensitivity (2.83V, 1m): 92dB,Crossover Frequency: 3.5kHz, Mounting Depth: Woofer: 2-1/16" (53mm), Tweeter: 1-1/4" (32mm), Cut-out Diameter: Woofer: 5" (127mm), Tweeter: 1-13/16" (47mm).

REF 6500CS REF 6502 I

2-way system 165mm (6.5") 2-way 165mm (6.5") 3-way 165mm (6.5")

2825.1575.-

Power Handling: RMS: 90 watts (Peak: 270 watts), Sensitivity (2.83V/1m): 92dB, Frequency Response: 53Hz 21kHz, Crossover Frequency: 3.5kHz, Nominal Impedance: 4 Ohms, Woofer: Mounting Depth: 62mm, Cutout diameter: 1427mm, Tweeter: Mounting Depth: 32mm, Cutout diameter: 47mm.
Speaker Impedance: 4 Ohms, Power Handling: 60W RMS (180W Peak), Frequency Response: 53Hz 21kHz, Sensitivity (2.83V, 1m): 92dB, Mounting Depth: 66 mm.

REF 6513CS

2964.-
System Power Handling: 125 watts, System Sensitivity: 90 dB, Frequency Response: 60 Hz ~ 20 kHz.AUTOMOTIVE COMPONENT SPEAKER SYSTEM.
REF 6802CF REF 6912 I REF 8003 I REF 853 I
6x8" 2-way 6x9" Auto 3-way 200mm 3-way,200mm tria

3tk 1tk 5tk 1tk

1528.1935.2269.2192.-