SCS145.5 OM

7/21/04

12:44 PM

Page 1
SURROUND CINEMA SPEAKERS SCS145.5

OWNERS GUIDE

Page 2

READ FIRST!

Important Safety Precautions!
13. Unplug this apparatus during lightning storms or when unused for long periods of time. 14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 15. Do not use attachments not recommended by the product manufacturer, as they may cause hazards. 16. This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. For products intended to operate from battery power, or other sources, refer to the operating instructions. 17. If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/ NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. See Figure A. 18. An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits, as contact with them might be fatal. 19. Do not overload wall outlets, extension cords, or integral convenience receptacles, as this can result in a risk of fire or electric shock. 20. Never push objects of any kind into this product through openings, as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product. 21. The apparatus shall not be exposed to dripping or splashing, and no objects filled with liquids, such as vases, shall be placed on the apparatus. 22. Do not attempt to service this product yourself, as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. 23. When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock or other hazards. 24. Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition. 25. The product should be mounted to a wall or ceiling only as recommended by the manufacturer.
1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with a dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturers instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves or other apparatus (including amplifiers) that produce heat. 9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A groundingtype plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10. Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles and the point where they exit from the apparatus. 11. Only use attachments/accessories specified by the manufacturer. 12. Use only with the cart, stand, tripod, bracket or table specified by the manufacturer or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

Figure A. Example of Antenna Grounding as per National Electrical Code, ANSI/NFPA 70

Page 3

THANK YOU FOR CHOOSING JBL
For more than 50 years, JBL has been involved in every aspect of music and film recording and reproduction, from live performances to the recordings you play in your home, car or office. Were confident that the JBL system you have chosen will provide every note of enjoyment that you expected and that when you think about purchasing additional audio equipment for your home, car or office, you will once again choose JBL. Please take a moment to register your product on our Web site at www.jbl.com. It enables us to keep you posted on our latest advancements, and helps us to better understand our customers and build products that meet their needs and expectations. JBL Consumer Products

INCLUDED

Four satellites for left, right and surrounds. Wall-mount brackets.
One center channel speaker with adjustable support leg.

Powered subwoofer.

Two 20' speaker cables for connection from receiver to subwoofer. Two 15' speaker cables for connection from subwoofer to front speakers.
Three 40' speaker cables for connection from receiver to rear satellites and center speaker.

Page 4

SPEAKER PLACEMENT
FRONT SPEAKERS CENTER CHANNEL SUBWOOFER SPEAKER

0-2 ft.

Stands shown are optional.

SURROUND SPEAKERS

The front speakers should be placed the same distance from each other as they are from the listening position. They should be placed at about the same height from the floor as the listeners ears will be, or they may be angled toward the listeners. The center channel speaker should be placed slightly behind the front left and right speakers, and no more than two feet above or below the tweeters of the left and right speakers. It is often convenient to set the center speaker on top of the television set, as shown in the drawing. Use the supplied support leg to aim it toward the listener by screwing the leg in to angle the speaker up, or unscrewing the leg
slightly to angle the speaker down. The surround speakers should be placed slightly behind the listening position and, ideally, should face each other and be at a level higher than the listeners ears. If that is not possible, they may be placed on a wall behind the listening position, facing forward. In Dolby* Digital and DTS systems, it is best to aim all of the speakers (except the subwoofer) toward the listening position at about earlevel height. In systems where only analog surround processing (such as Dolby Pro Logic*) is available, it may be preferable to aim the speakers straight out from the wall to obtain a more diffuse sound.

The low-frequency material reproduced by the subwoofer is mostly omnidirectional, and this speaker may be placed in a convenient location in the room. However, bass reproduction will be maximized when the subwoofer is placed in a corner along the same wall as the front speakers. Experiment with subwoofer placement by temporarily placing the subwoofer in the listening position and moving around the room until the bass reproduction is best. Place the subwoofer in that location.

Page 5

MOUNTING OPTIONS

SATELLITES AND SURROUNDS

On shelves.

WALL-MOUNTING

On the wall. Wall brackets are included.
On optional stands (FS1000).
Attach plate to wall. The brackets should be placed, if possible, so that the screws will fasten into a wooden wall stud. If that is not possible, use properly selected wall anchors. The customer is responsible for proper selection and use of mounting hardware, available through hardware stores, to properly and safely wallmount the speakers.
Slide speaker onto support. IMPORTANT NOTE: The satellite speaker, when mounted on these brackets, can only be adjusted horizontally (left or right). The speaker cannot be adjusted vertically (up or down) or otherwise tilted. Any attempt to do so will damage the speaker bracket wall plate and/or support and such damage will not be covered under warranty.
Place speaker and support on wall plate. Make sure that at least 1/4" (6mm) of the wall plate metal shaft is inserted into the support cavity. Continue to firmly press the support onto the wall plate metal shaft until it is fully secured in place.
MOUNTING THE SATELLITES ON OPTIONAL FS1000 FLOOR STANDS
1. Attach the stand adaptor to the top of the stand upright with the pins toward the rear of the stand. Fasten the adaptor to the upright with the supplied screw. 2. Place the loudspeaker securely on the stand by inserting the adaptor pin
into the grommet on the bottom of the speaker. 3. Connect the wire to the loudspeaker, remembering to preserve the polarity (+ and ) (see page 6).

Page 6

SPEAKER CONNECTIONS

CONNECTION TIPS

Separate and strip the ends of the speaker wire as shown. The wires supplied with the system may already be stripped and tinned for easy insertion into the speaker terminals. Speakers and electronics terminals have corresponding (+) and () terminals. Most manufacturers of speakers and electronics, including JBL, use red to denote the (+) terminal and black for the () terminal. The (+) lead of the speaker wire is noted with a stripe. It is important to connect both speakers identically: (+) on the speaker to (+) on the amplifier and () on the speaker to () on the amplifier. Wiring out of phase results in thin sound, weak bass and a poor stereo image. With the advent of multichannel surround sound systems, connecting all of the speakers in your system with the correct polarity remains equally important in order to preserve the proper ambience and directionality of the program material.

To connect the supplied speaker wires to the speaker terminals, press the red or black plastic tab for the desired terminal, insert the bare end of the wire into the hole and release the tab. Gently tug on the wire to make sure that it is fully inserted.

Page 7

DOLBY DIGITAL OR DTS (OR OTHER DIGITAL SURROUND MODE) CONNECTION
RECEIVER SUBWOOFER LINE LEVEL IN LFE OUT LFE INPUT
Use this installation method for Dolby Digital, DTS or other digital surround processors: Use the line-level input jack marked LFE for the LowFrequency Effects channel.
Connect this jack to the LFE output or subwoofer output on your receiver or amplifier. Connect each speaker to the corresponding speaker terminals on your receiver or amplifier. Make sure that you have configured your surround sound processor for Subwoofer On. The receiver should be config-
ured for 5.1-channel operation, and the front left, front right, center and rear speakers should all be set to Small. If your receiver allows you to set the crossover frequency between the subwoofer and the main speakers, select either 120Hz or 150Hz, or select the setting that is the closest frequency below these.
DOLBY PRO LOGIC (NON-DIGITAL) LINE LEVEL
Use this installation method for Dolby Pro Logic applications (not Dolby Digital, DTS or other digital processing), where the receiver/ processor is equipped with a subwoofer output, or a
volume-controlled preamp (line-) level output: Use RCA-type interconnects to connect the line-level subwoofer outputs on your receiver or amplifier to the line-level inputs on the subwoofer. IMPORTANT: Do not
use the LFE input on the subwoofer with Dolby Pro Logic processors. NOTE: If your receiver or amplifier only has one subwoofer output jack, then you will need to use a Y-connector (not included). Plug the male end of the Yconnector into your receiver or amplifiers subwoofer output jack, and connect each of the two female ends to separate RCA-type interconnects. Finally, plug the RCAtype interconnects into the line-level inputs on the subwoofer. Connect each speaker to the corresponding speaker terminals on your receiver or amplifier.
Make sure your receiver or processor is correctly configured to indicate that the subwoofer is On. Note for advanced users: If your receiver/processor has a built-in low-pass crossover filter for the subwoofer output, you may use the LFE input to bypass the subwoofers internal crossover.

Page 8

DOLBY PRO LOGIC (NON-DIGITAL) SPEAKER LEVEL

Use this installation method for Dolby Pro Logic applications (not Dolby Digital, DTS or other digital processing), where the receiver/processor does not have a subwoofer output, or a volume-controlled preamp (line-) level output: Connect your receiver or amplifiers front left and right speaker terminals to the left and right terminals on the subwoofer that are marked Speaker Level In. Connect the left and right terminals on the subwoofer that are marked Speaker Level Out to the corresponding terminals on the back of your front left and right speakers. Connect your receiver or amplifiers center and surround speaker terminals to the corresponding terminals on the back of your center and surround speakers.

Left Front

Right Front Center

Subwoofer

+ OUT IN

SPEAKER LEVEL R

Receiver
Left Front Center Right Front

Left Surround

Right Surround

Page 9

OPERATION
Move the Master Power switch (marked Power ) to the (On) position to use the subwoofer. The SUB145 subwoofer will automatically turn on or go into standby (sleep) mode when left in the auto mode (Auto/On switch in the Auto position). When your receiver or amplifier is off, or is not sending program material to the subwoofer, the subwoofer will be in standby mode (LED will be red). When the subwoofer senses an audio signal, it will automatically turn on (LED will be green). If the subwoofer does not sense a signal after approximately twenty minutes, it will automatically go back into standby mode. When the Auto/On switch is switched to the On position, the subwoofer will remain on, whether or not program material is playing. If you will be away from home for an extended period of time, or if the subwoofer will not be used, switch the Master Power switch to the Off position.
SPEAKER LEVEL + L R + OUT IN

LINE LEVEL IN LFE

AUTO ON

SUBWOOFER LEVEL

IMPORTANT: CONNECT STRIPED WIRE TO RED ( + ) SPEAKER TERMINAL.

GREEN: ON RED: STANDBY

SUB145

CAUTION

RISK OF ELECTRIC SHOCK DO NOT OPEN

VOLUME Subwoofer Level

Volume may be adjusted using the Subwoofer Level control as shown.

Subwoofer Level

Page 10

TROUBLESHOOTING

If there is no sound from any of the speakers: Check that receiver/amplifier is on and a source is playing. Check that the powered subwoofer is plugged in, and that its Power switch is switched on ( position). Check all wires and connections between receiver/ amplifier and speakers. Make sure all wires are connected. Make sure none of the speaker wires are frayed, cut or punctured, or touching each other. Review proper operation of your receiver/amplifier. If there is no sound coming from one speaker: Check the Balance control on your receiver/amplifier. Check all wires and connections between receiver/ amplifier and speakers. Make sure all wires are connected. Make sure none of the speaker wires are frayed, cut or punctured, or touching each other. In Dolby Digital or DTS modes, make sure that the receiver/processor is configured so that the speaker in question is enabled. Turn off all electronics and switch the speaker in question with one of the other speakers that is working correctly. Turn everything back on, and determine whether the problem has followed the speaker, or has remained in the same channel. If the problem is in the same channel, the source of the problem is most likely with your receiver or amplifier, and you should consult the owners manual for that product for further information. If the problem has followed the speaker, consult your dealer for further assistance or, if that is not possible, visit www.jbl.com for further information. If there is no sound from the center speaker: Check all wires and connections between receiver/ amplifier and speaker. Make sure all wires are connected. Make sure none of the speaker wires are frayed, cut or punctured, or touching each other. If your receiver/processor is set in Dolby Pro Logic mode, make sure the center speaker is not in phantom mode. If your receiver/processor is set in Dolby Digital or DTS modes, make sure the receiver/ processor is configured so that the center speaker is enabled. If the system plays at low volumes but shuts off as volume is increased: Check all wires and connections between receiver/ amplifier and speakers. Make sure all wires are connected. Make sure none of the speaker wires are frayed, cut or punctured, or touching each other. If more than one pair of main speakers is being used, check the minimum impedance requirements of your receiver/amplifier. If there is low (or no) bass output: Make sure the connections to the left and right Speaker Inputs have the correct polarity (+ and ). Make sure the subwoofer is plugged into an active electrical outlet, and is turned on (Power switch in the position). In Dolby Digital or DTS modes, make sure your receiver/processor is configured so that the subwoofer and LFE output are enabled.

Page 11

If there is no sound from the surround speakers: Check all wires and connections between receiver/ amplifier and speakers. Make sure all wires are connected. Make sure none of the speaker wires are frayed, cut or punctured, or touching each other. Review proper operation of your receiver/amplifier and its surround sound features. Make sure the movie or TV show you are watching is recorded in a surround sound mode. If it is not, check to see whether your receiver/amplifier has other surround modes you may use. In Dolby Digital or DTS modes, make sure your receiver/processor is configured so that the surround speakers are enabled. Review the operation of your DVD player and the jacket of your DVD to make sure that the DVD features the desired Dolby Digital or DTS mode, and that you have properly selected that mode using both the DVD players menu and the DVD discs menu.

Page 12

SPECIFICATIONS

SCS145.5 System

Frequency Response 35Hz 20kHz (6dB)

Amplifier 100 Watts RMS

Satellites
Recommended Power Watts Impedance 8 Ohms nominal Sensitivity 86dB @ 1 Watt/1 meter Tweeter One 1/2" (13mm) titanium-laminate dome, video-shielded Midrange One 3" (75mm) driver, video-shielded Dimensions (H x W x D) 4-3/8" x 3-3/16" x 3-3/4" 111mm x 81mm x 95mm Weight 1.1 lb/0.5kg
Woofer 8" (200mm) Enclosure Bass reflex
Dimensions (H x W x D) 15" x 13" x 14" 381mm x 330mm x 356mm Weight 30 lb/13.6kg

Center

Recommended Power Watts Impedance 8 Ohms nominal Sensitivity 86dB @ 1 Watt/1 meter Tweeter One 1/2" (13mm) titanium-laminate dome, video-shielded Midrange Dual 3" (75mm) drivers, video-shielded Dimensions (H x W x D) 3-1/4" x 7-5/8" x 3-3/4" 83mm x 194mm x 95mm Weight 1.89 lb/0.86kg
All features and specifications are subject to change without notice. *Trademarks of Dolby Laboratories. DTS is a registered trademark of Digital Theater Systems, Inc.

PRODUCT LINE:

PRO SOUND COMES HOME
JBL Consumer Products 250 Crossways Park Drive, Woodbury, NY Balboa Boulevard, Northridge, CA 91329 516.255.4JBL (4525) (USA only) www.jbl.com 2004 Harman International Industries, Incorporated JBL is a registered trademark of Harman International Industries, Incorporated. Part No. 406-000-05100

SURROUND CINEMA SPEAKERS MODEL: SCS145.5
DESIGN GOAL: Bring the thrill of live performance and movie sound to the home environment by calling on JBLs professional engineering leadership. SATELLITE TYPE: Titanium-laminate-dome tweeter,

sealed enclosure

SUBWOOFER TYPE: Bass-reflex enclosure PORT DESIGN: FreeFlow flared
PROFESSIONAL REFERENCE: Cinema Loudspeaker Series

JBL Home Audio

CJENIK 20.08.2008

NORTHRIDGE E SERIES

E20 E80 EC25 E150P NORTHRIDGE E CINE PACK
all models available in Brown Cherry and Black Satin. Beech finish only as Cine Pack! 2 WAY 5" BOOKSHELF 3 WAY DUAL 6" FLOORSTANDER 2 WAY DUAL 5" CENTER CHANNEL 10" 150 WATT POWERED SUBWOOFER 5.1 HCS ; E20 + E80+ EC25 & E150P all models available in Brown Cherry, Beech and Black Satin 3 WAY 5" BOOKSHELF / WALL-MOUNT SATELLITE SPEAKER 3 WAY 5" BOOKSHELF 3 WAY 5 1/4" BOOKSHELF 4 WAY DUAL 6" FLOORSTANDING SPEAKER 4 WAY DUAL 8" FLOORSTANDING SPEAKER 4 WAY DUAL 10" FLOORSTANDING SPEAKER 3 WAY DUAL 5 1/4 " CENTER CHANNEL SPEAKER 10" 200 WATT POWERED SUBWOOFER 12" 400 WATT POWERED SUBWOOFER Pair Pair Pair Pair Pair Pair Each Each Each Special Offer ! Pair Pair Each Each Sys
mpc/kn 1.480,00 3.980,00 1.180,00 2.680,00 8.854,00 mpc/kn 1.780,00 1.880,00 2.380,00 5.280,00 6.080,00 6.880,00 1.380,00 2.980,00 3.880,00 mpc/kn

Pair Pair Pair Each Each

ES SERIES
ES10 ES20 ES30 ES80 ES90 ES100 ES25C ES150P ES250P

STUDIO L SERIES

L820 L830 L890 LC2 L8400P
all models available in Brown Cherry and Black Ash 4 WAY 6" MIRROR-IMAGE WALL-MOUNT SATELLITE SPEAKER 3 WAY 6" BOOKSHELF SPEAKER 4 WAY DUAL 8" FLOORSTANDING SPEAKER 4 WAY DUAL 6" WALL-MOUNT CENTER CHANNEL SPEAKER 12" 400 WATT POWERED SUBWOOFER
3.180,00 3.180,00 7.780,00 2.580,00 5.880,00 mpc/kn

LS SERIES

LS40 LS60 LS80 LS Center LS 120P
all models available in Ebony veneer with Mahogany tint 3-WAY 6" BOOKSHELF WITH HORN LOADED UHF & HF SPEAKER 3-WAY DUAL 6" FLOORSTANDING WITH HORN LOADED UHF & HF SPEAKER 3-WAY DUAL 8" FLOORSTANDING WITH HORN LOADED UHF & HF SPEAKER , Award for Best Speaker in Year 2008/2009 3-WAY DUAL 6" CENTER WITH HORN LOADED UHF & HF SPEAKER 12" 400 WATT RMS (700W PEAK) POWERED SUBWOOFER EISA new ! new ! new ! new ! new ! Pair Pair Pair Each Each
8.780,00 14.880,00 17.880,00 5.280,00 5.980,00 mpc/kn

ARRAY SERIES

ARRAY 800 ARRAY 880 ARRAY 1000 ARRAY 1400 ARRAY 1500
3-WAY 200MM (8") BOOKSHELF SPEAKER 3-WAY DUAL 200MM (8") CENTER CHANNEL 3-WAY FLOOR STANDING , 250MM (10" ) WOOFERS 3-WAY FLOOR STANDING , 350MM (14" ) WOOFERS 15" ,375MM , 1000 WATTS POWERED SUBWOOFER Pair Each Pair Pair Each
31.980,00 18.980,00 43.980,00 61.980,00 23.380,00 mpc/kn

PROJECT K2 SERIES

EVEREST II K2 S9800 Special Edition K2 S5800 K2 S4800
3-WAY FLOOR STANDING , DUAL 15" WOOFER , Mahogany,Cheery or Black Ebony 3-WAY FLOOR STANDING , 15" WOOFER, Black High Gloss Zebrawoood , Mahogany 3-WAY FLOOR STANDING , TWO 12" WOOFERS ,Walnut 3-WAY FLOOR STANDING Pair Pair Pair Pair
tel ! 199.800,00 109.800,00 86.800,00 mpc/kn 14.980,00
TL SERIES Limited Edition

TL 260BQ (L&R)

4-WAY ,300mm (12") POLYPLAS FLOORSTANDING SPEAKER, piano black Pair

www.jbl.com

Uvoz i distibucija za Hrvatsku i BiH:
MEDIA AUDIO d.o.o., Gundulieva 26a, 21000 SPLIT, tel: 021/323 550, fax:. 021/315 220, e-mail: info@mediaaudio.hr, web: www.mediaaudio.hr Maloprodaja: "DOBAR ZVUK" SPLIT, Gundulieva 20, tel/fax 021/"DOBAR ZVUK" ZAGREB, Preradovieva 88, tel/fax 01/97

HOME CINEMA SOUND SERIES

CST 55 CSC 55 CSS 10 CINEMA SOUND HCS
2 - WAY DUAL 130mm (5" ) POLYPLAS TOWER SPEAKER DUAL 130mm (5" ) POLYPLAS CENTER CHANNEL 150 W 250mm (10") SUBWOOFER 5.1 SIMPLY CINEMA SPEAKER SYSTEM, BLACK Glossy Edition WATT ACTIVE SUBWOOFER,4x 5 TOWER SPEAKER , DUAL 5 CENTER

Ea Ea Ea Sys

mpc/kn 1.680,00 1.480,00 2.480,00 9.680,00

CINEMA SOUND SERIES

mpc/kn
2.1 Cinema Sound Sys,with single 3" inch woofer satelite Small Sat, 6" Sub 5.1 Cinema Sound Sys,with single 3" inch woofer satelite Small Sat, 6" Sub 2.1 Cinema Sound Sys,with doube 3" inch woofer satelite Small Sat, 8" 100W subwoofer 5.1 Cinema Sound Sys,with doube 3" inch woofer satelite Small Sat, 8" 100W subwoofer BLACK ALUMINUM TOWERSTAND FOR CS46,68,680. SATELLITE Sys Sys Sys Sys Pair
CS 46 CS 460 CS 68 CS 680

CS STAND

2.080,00 3.080,00 2.680,00 3.680,00 880,00 mpc/kn
CINEMA SOUND POWERED SERIES
CSP 430 CSP 630 CSP 1550 CS360XCITE
Complete 5.1 Home Theaer System. Features: CS460 speakers incl CS460 speaker system - DiVx&HDMI 5x35w DD&DTS - Dual USB on the go - HDMI output - 720 Pand - high resolution&intuitive on screen interface - Plays MP3, WMA files Complete 5.1 Home Theaer System incl CS680 speaker system - DiVx&HDMI 5x35w DD&DTS - Dual USB on the go - HDMI output - 720 Pand - high resolution&intuitive on screen interface - Plays MP3, WMA files Complete 5.1 Home Theaer System incl Cinema sound speaker system - DiVx&HDMI 5x65w DD&DTS Dual USB on the go - HDMI output - 720 Pand - high resolution&intuitive on screen interface - Plays MP3, WMA files new ! Limited Qty. only! 5.1 SIMPLY CINEMA SPEAKER SYSTEM, SILVER/BLACK WATT ACTIVE SUBWOOFER, 3 SATELLITES, DUAL 3 CENTER 5.1 SIMPLY CINEMA SPEAKER SYSTEM, AVAILABLE IN CHERRY & BEECH FINISH ALUMINUM TOWERSTAND FOR SCS140,146,200.5, 260.5. SATELLITE new !
6.280,00 6.980,00 12.980,00 TEL ! mpc/kn

Sys Nov.08 !

SIMPLY CINEMA SYSTEMS

SCS 200.5 SCS 178

FS 1000 WEM-1

Sys Sys Pair Nov.08 !

2.980,00 3.480,00 880,00 TEL ! mpc/kn 1.280,00 2.480,00 1.390,00 1.590,00 240,00 240,00 mpc/kn

CONTROL SERIES

CONTROL ONE CONTROL 2.4G CONTROL NOW CONTROL NOW AW PMBBK PMBWK
2-WAY 4" PERSONAL MONITOR LOUDSPEAKER, BLACK or SILVER INCLUDES ADJUSTABLE WALL BRACKET WBC 1 IN BOX WIRELESS POWERED SPEAKER SYSTEM , 2-WAY 4" PERSONAL MONITOR LOUDSPEAKER, BLACK 2-WAY INDOOR LOUDSPEAKER, DUAL 110mm mid-woofer + Bi-Radila Horn 19mm Titanium Tweeter , BLACK , INCLUDES WALL BRACKET 2-WAY INDOOR-OUTDOOR (all Weather) LOUDSPEAKER, DUAL 110mm mid-woofer + Bi-Radila Horn 19mm Titanium Tweeter , WHITE , INCLUDES WALL BRACKET Pole mount bracket kit for Control NOW - Black Pole mount bracket kit for Control NOW - White new ! Pair

new ! new ! new !

Each Each Each
IN-WALL/IN-CEILING SPEAKERS

HTI SERIES

HTi55 HTi8 HTi6 HTi6C HTi88

SOUNDPOINT SERIES

2-WAY DUAL 5" VERTICAL/HORIZONTAL LCR IN-WALL SPEAKER ,WHITE 2-WAY 8" IN-WALL, WHITE 2-WAY 6,5" IN-WALL, WHITE 2-WAY 6.5" COAX CEILING, WHITE DUAL 8" IN-WALL SUBWOOFER,WHITE

Each Pair Pair Pair Each

1.080,00 2.180,00 1.480,00 1.280,00 1.880,00
SP5II SP6II SP8II SP6CII SP6CSII SP8CII
2-WAY 5" IN-WALL, WHITE 2-WAY 6,5" IN-WALL, WHITE 2-WAY 8" IN-WALL, WHITE 2-WAY 6.5" COAXIAL CEILING SPEAKER,WHITE 2-WAY 6.5" STEREO ROUND CEILING SPEAKER ,WHITE 2-WAY 8" ROUND CEILING SPEAKER,WHITE
Pair Pair Pair Pair Each Pair
1.120,00 1.280,00 1.820,00 1.080,00 1.180,00 1.280,00