Project Array Subwoofer

1500 Array

Service Manual

JBL Consumer Products 250 Crossways Park Dr. Woodbury, New York 11797 Rev0 4/2006

1500 Array Subwoofer

- CONTENTS BASIC SPECIFICATIONS..1 PACKING...2 DETAILED SPECIFICATIONS..3 CONNECTIONS..5 OPERATION.6 BASIC TROUBLESHOOTING7 EXPLODED VIEW/PARTS LIST.8 TEST SET-UP AND PROCEDURE.9 BLOCK DIAGRAM.10 ELECTRICAL PARTS LIST.11 P.C.B. DRAWINGS..16 IC/TRANSISTOR PINOUTS..22 SCHEMATICS.23
1500 ARRAY SPECIFICATIONS
General Output Low-Frequency Transducer Frequency Response (-3dB) Crossover Frequencies Port Dimensions (H x W x D) 1000W W1500H 15" Pulp-cone driver 25Hz 400Hz, variable 40Hz-140Hz HP 4" Flared 23" x 19-1/2" x 19" (584mm x 495mm x 483mm) 21" (533mm) Deep with grille 125 lb (57kg)

Weight

JBL continually strives to update and improve existing products, as well as create new ones. The specifications and details in this and related JBL publications are therefore subject to change without notice.

Ref# 5 6

Part Number 361041-002 331994-001 361408-001 354374-001 354374-001 340805-006
Description 1500 Array Owners Manual JBL Warranty Card 1500 Array Outer Carton Packing Foam (Top) Packing Foam (Bottom) (Plate) Feet

Qty 1 4

1500 Array Powered Sub/ Plate Amp
LINE VOLTAGE US 120VAC/60Hz EU 230VAC/50-60Hz Asia 100VAC/50Hz Yes/No YES YES YES Hi/Lo Line 108-132 207-264 90-110 Nom. 100 QA Test Limits Unit Vrms Vrms Vrms Notes Normal Operation Normal operation, MOMS required Normal operation, MOMS required

Parameter Amp Section

Specification

Conditions

Type (Class AB, D, other) Load Impedance (speaker) Rated Output Power THD @ Rated Power THD @ 1 Watt

D 0.5 0.1

n/a Ohms Watts % %

n/a n/a 0.2

Bridge type amplifier, None of the speaker terminals must be connected to system GND at any time. Nominal 1 input driven 22K filter 22K filter Test frequency 100 Hz

Dynamic Power DC Offset

700 20

Watts mV-DC

690 100
Damping factor Input Sensitivity Input Frequency Line level input Signal to Noise SNR-A-Weighted SNR-unweighted SNR rel. 1W-unweighted Residual Noise Floor

>20

Power is the average measurement of the first four consecutive peaks of 3/20 Cycles @ 50 Hz, burst test into 8 Ohms, input the burst signal driven with 800mV RMS @ Speaker Outputs Measured at the speaker cable. 500 Watts, measured at speaker output terminals located at the amp board. Measured at amplifier board

100 11.69

Hz mVrms

100 2dB

Nominal Freq. To 1 Watt Single input driven, Ap Zo=600 Ohms, LFE mode, Volume ctrl. at max.

70 0.5

dBA dBr dBr mVrms
Relative to rated power (650 Watts) A-Weighting filter Relative to rated power (650 Watts) 22K filter Relative to 1W Output 22K filter Volume @max, LFE Mode, using RMS reading DMM/VOM (or A/P) Volume @max, LFE Mode, w/ A/P Swept Bandpass Measurement (Line freq.+ harmonics)

Residual Noise Floor Input Impedance Line Input Filters LP 4th order variable Subsonic filter (HPF) 3rd Orde LFE Mode Features Line Level output Volume pot Taper (lin/log) Variable crossover 40-140 Hz LP Selector switch LFENormal Phase switch Auto- On-Off selector Input Configuration Single Line input Line output configuration Single Line level output Signal Sensing (ATO) Auto-Turn-On (yes/no) ATO Input test frequency ATO Level, Line Input ATO Turn-on time Auto Mute/ Turn-OFF Time Power on Delay time ATO mode ON mode

0.5 mVrms(max)

Nominal
40-140 Hz Fixed Hz Fixed Hz

LP Mode switch at LFE

YES LOG YES YES YES YES
functional functional functional functional functional functional
RCA Line buffered line level output A Taper 4th Order LP Filter, 2nd order fix and 2nd order variable. Pass through from the speaker input section Disables LP filter, intended for LFE Switch located at the back panel

functional

Single RCA jack (BLK Color)
Gain=0dB respect to line level input, Functional Zo=600 Ohms Single RCA jack (BLK Color)

YES 50 2.15

Hz mV seconds minutes
functional Auto - on selection switch in Auto functional " functional " Amp connected and AC on, then functional input signal applied (T) Time before muting, after input 17 signal is removed Auto turn of time (T) must be 10 > T < 17 Minutes

sec. sec.

After applying the minimum ATO voltage (2mVRMS) After turning the stand-by knob to ON position
Parameter Specification Unit QA Test Limits Conditions Notes
Transients/Pops ATO Transient Turn-on Transient Turn-off Transient Efficiency Efficiency Stand-by Input Power

mV-peak mV-peak mV-peak

n/a @ Speaker Output 1V-pk-pk @ Speaker Output 1V-pk-pk @ Speaker Output
AC Line cycled from OFF to ON AC Line cycled from ON to OFF
500W of output power into rated impedance @ nominal line voltage, Amp in OFF state, RED LED activated
Nominal Line voltage Maximum allowable input power LED in RED, Class D inactive Maximum allowable input power under nominal Input voltage and frequency, in stand-by mode (HOT or COLD operation, LED GREEN). Class D active but no stimulus signal applied. 500 Watts into rated impedance 8 Ohms Temperature rise in accessible metal parts should not exceed 35K rise for domestic version or 30K rise for European versions (refer to requirements sheet). Unit is protected for over-temperature conditions Relay opens during a DC output condition
Stand-by Input Power Power Cons. @ 500W Protection

10 678

Watts Watts
@ nom. line voltage, Amp in On state, Green LED activated @ nom. line voltage

Thermal Protection DC Offset Protection Line Fuse Rating Japan 100V & USA- Versions Europe 220-240V
YES YES 6.3 3.15 Amps Amps
functional @1/8 max unclipped Power DC present at Speaker Out leads
Type-T or Slo Blo-250 V UL, PSE Approved Type-T, Low breaking capacity-250VSEMKO Approved

Project Array OM

1/10/06

12:21 PM

Page 8
1500 Array Subwoofer SPEAKER CONNECTIONS
Subwoofer Controls and Connections (0 Array Only)

Line-Level Input

Line-Level Output Power Indicator Subwoofer Level (Volume) Control Crossover Adjustment Phase Switch LP/LFE Selector On/Off Auto Switch Power Switch Connection: If you have a Dolby Digital or DTS receiver/processor with a low-frequencyeffects (LFE) output, set LFE/LP switch to LFE. If you prefer to use the crossover built into the 1500 Array, set the LFE/LP Switch to LP.

SUBWOOFER OR LFE OUTPUT

The 1500 Array includes a line output. This output allows you to daisy chain one 1500 Array to multiple 1500 Array subwoofers. Simply connect the first subwoofer as described above and then run a subwoofer cable from the line output(s) to the line input on the next sub.

Page 9

1500 Array Subwoofer 1500 ARRAY OPERATION
Power On Plug your subwoofers AC cord into a wall outlet. Do not use the outlets on the back of the receiver. Initially set the Subwoofer Level (Volume) Control to the min position. Turn on your sub by pressing the Power Switch on the rear panel. Auto On/Standby With the Power Switch in the on position, the Power Indicator LED will remain backlit in red or green to indicate the On/Standby mode of the subwoofer. RED = STANDBY (No signal detected, Amp Off) GREEN = ON (Signal detected, Amp On) The subwoofer will automatically enter the Standby mode after approximately 10 minutes when no signal is detected from your system. The subwoofer will then power ON instantly when a signal is detected. During periods of normal use, the Power Switch can be left on. You may turn off the Power Switch for extended periods of nonoperation, e.g., when you are away on vacation. If the Auto Switch is in the on position, the subwoofer will remain on. Adjust Level Turn on your entire audio system and start a CD or movie soundtrack at a moderate level. Turn up the Subwoofer Level (Volume) Control about halfway. If no sound emanates from the subwoofer, check the AC-line cord and input cables. Are the connectors on the cables making proper contact? Is the AC plug connected to a live receptacle? Has the Power Switch been pressed to the on position? Once you have confirmed that the subwoofer is active, proceed by playing a CD or movie. Use a selection that has ample bass information. Set the overall volume control of the preamplifier or stereo to a comfortable level. Adjust the Subwoofer Level (Volume) Control until you obtain a pleasing blend of bass. Bass response should not overpower the room but rather should be adjusted so there is a harmonious blend across the entire musical range. Many users have a tendency to set the subwoofer volume too loud, adhering to the belief that a subwoofer is there to produce lots of bass. This is not entirely true. A subwoofer is there to enhance bass, extending the response of the entire system so the bass can be felt as well as heard. However, overall balance must be maintained or the music will not sound natural. An experienced listener will set the volume of the subwoofer so its impact on bass response is always there but never obtrusive. Crossover Adjustments NOTE: This control will have no effect if the LP/LFE Selector Switch is set to LFE. If you have a Dolby Digital or DTS processor/receiver, the Crossover Frequency is set by the processor/receiver. Consult your owners manual to learn how to view or change this setting. The Crossover Adjustment Control determines the highest frequency at which the subwoofer reproduces sounds. If your main speakers can comfortably reproduce some low-frequency sounds, set this control to a lower frequency setting, between 50Hz and 100Hz. This will concentrate the subwoofers efforts on the ultradeep bass sounds required by todays films and music. If you are using smaller bookshelf speakers that do not extend to the lower bass frequencies, set the Crossover Adjustment Control to a higher setting, between 120Hz and 150Hz. Phase Control The Phase Switch determines whether the subwoofer speakers pistonlike action moves in and out with the main speakers (0) or opposite the main speakers (180). Proper phase adjustment depends on several variables, such as subwoofer placement and listener position. Adjust the Phase Switch to maximize bass output at the listening position.

BASIC TROUBLESHOOTING

If there is low (or no) bass output
Make sure the connections to the left and right Speaker Inputs have the correct polarity (+ and ).
Make sure the subwoofer is plugged into an active electrical outlet.
Make sure the Power Switch is on.
In Dolby Digital or DTS modes, make sure your receiver/processor is configured so that the subwoofer and LFE output are enabled.
Adjust the Subwoofer Level Control
1500 Array Subwoofer 1500 ARRAY SUB EXPLODED VIEW
X RAY VIEW FOR ILLUSTRATIVE PURPOSES ONLY DAMPING MATERIAL NOT SHOWN
1500 ARRAY MECHANICAL PARTS LIST
Item # 13 Description CABINET ASSEMBLY-1500 ARRAY 15" WOOFER-W1500H AMPLIFIER ASSEMBLY,120V-ARRAY POWER TRANSFORMER-1500 ARRAY BG PORT TUBE -1500 ARRAY CARBOARD TUBE,4 1/4x4x1/8x6-4338 FOOT,NUT,INSERT,BLK FOOT,SPIKE,BLK GRILLE,FRONT, 1500 ARRAY WOOFER SCREW,10-32 X 1,FIL,PH,BLK ZINC,LCS AMPLIFIER SCREW,8 X 1,PAN,PH,PB,BLK ZINC,LCS GASKET,DRVR,15" LOGO-JBL Part Number Not for Sale 353721-001 Not for Sale 361407-001 360806-001 47909-68 340805-004 340805-005 354507-001 804-01110-16 883-41110-16 338073-001 360813-001 Qty 1
1500 Array TEST PROCEDURE
Equipment needed: Function/signal generator/sweep generator Multimeter RCA cable General Unit Function (UUT = Unit Under Test) Switch/Controls: GAIN control full Counterclockwise (Min) CROSSOVER (Hz) Full Clockwise (140) PHASE switch - either position LFE/LP LP position 1) 2) 3) 4) 5) 6) From the signal generator, connect one line level (RCA) cable to the Line In jack on the UUT. Turn on generator; adjust to 200mV, 50 Hz. Plug AC power cord in UUT, turn power switch ON. LED should be ON (faceplate). Turn up LEVEL control to full Clockwise (Max). LED should be Green; Bass response should be heard and felt vigorously from woofer and port tube. Turn LEVEL control full Counterclockwise (Min). Turn power switch OFF.
Sweep Function 1) Follow steps 1-5 above, using a sweep generator as a signal source adjust the generator to 75mV, 50 Hz. 2) Sweep generator from 20Hz to 300Hz. Listen for any rattles, clicks, buzzes or any other noises. If any unusual noises are heard, test woofer according to the instructions below. Driver Function 1) Remove woofer from the enclosure. 2) Check DC resistance of woofer; it should be 5.9 10%, 3) Connect a pair of speaker cables to woofer terminals. Cables should be connected to an integrated amplifier fed by a signal generator. Turn on generator and adjust so that speaker level output is 6.0V. 4) Sweep generator from 20Hz to 1kHz. Listen to driver for any rubbing, buzzing, or other unusual noises.

1500 Array Subwoofer 1500 ARRAY BLOCK DIAGRAM
1500 Array 120V Electrical parts list

Part number DRIVER PCB

Resistors 024-000098-120ZS 024-100298-120ZS 024-100498-120ZS 024-100598-120ZS 024-110598-120ZS 024-200598-120ZS 024-220398-120ZS 024-220498-121ZS 024-220598-120ZS 024-220798-120ZS 024-270498-120ZS 024-390498-120ZS 024-390598-120ZS 024-470398-120ZS 024-470498-120ZS 024-470598-120ZS 024-470698-120ZS 024-560598-120ZS 024-680498-120ZS Capacitors 031-100244-100ZS 031-100343-100ZS 031-100344-100ZS 031-180344-100ZS 031-470244-102ZS 031-560243-100ZS 031-560343-102ZS 034-100614-300ZS Semiconductors 054-000100-100ZS 054-005501-100ZR 054-007200-100LZS 054-008406-000ZR 054-008408-000ZR 054-033906-100ZR 054-414803-100ZS 054-540100-100ZR 054-555100-100ZR 051-222200-100ZR 051-555100-000ZR 051-000600-100ZR 053-211100-000ZR Miscellaneous 072-040229-000ZR 072-040230-000ZR GR HEADER Right Angle PN:211-107-000-400 7PIN GR HEADER Right Angle PN:211-111-000-400 11PIN PIN2 PINGS SMD DIODE: PN:ES1D 200V 1A GR SMD ZENER DIODE PN:BZV55C3V6 (PHILIPS) GS SMD IC: (JRC) M072M-DUAL OP-AMP GR SMD ZEN DIODE:(PHILIPS) BZX84C10-7-F SOT-23 GR SMD ZEN DIODE:(PHILIPS) BZX84C5V6-7-F SOT-23 GR SMD Transistor (ON) PN:MMBT3906LT1G SOT23 GS SMD DIODE: PN:LL4148 MINI-MELF GR SMD Transistor PNP (ON SEN) MMBT5401 LT1 SOT-23 GR SMD Transistor (NPN) PN:MMBT5551 LT1R (ON) GR Transistor NPN (ON SEM) PN:MPS2222ARLRAR TO-92 GR Transistor NPN PN:2N5551 TO-92 GR Transistor NPN PN:MPSW06RLRA TO-92 (ON) GR IC:DIP,HALF-BRIDGE DRIVER PN:IR2111 8PIN (IR) D35,43 D60 U9,10 D42,49 Z7,8 Q34,35 D36,39,46,52,61 Q33,40 Q32 Q20,22 Q21,23 Q31 U7,1 GS SMD Ceramic cap. 0u01/50V K 0805 X7R GS SMD Cap. 100pF/50V J 0805 NPO GS SMD Cap. 0u1/50V K 0805 X7R GS SMD Cap. 0u18/50V K 0805 X7R GS SMD Cap. 0u047/50V K 0805 X7R GS SMD Cap. 56pF/50V J 0805 NPO GS SMD Cap. 560pF/50V J 0805 NPO GS Elec. Cap. 100uF/16V M (R)0611 P:2.5 C108,118,131,140 C81,84 C75-78,82,85 C80,83 C93,94,101,124 C92,102,105,125 C79 CGS SMD Resistor 0R 1/8W J 0805 GS SMD Resistor 10R 1/8W J 0805 GS SMD Resistor 1K 1/8W J 0805 GS SMD Resistor 10K 1/8W J 0805 GS SMD Resistor 11K 1/8W J 0805 GS SMD Resistor 20K 1/8W J 0805 GS SMD Resistor 220R 1/8W J 0805 GS SMD Resistor 2K2 1/8W J 0805 GS SMD Resistor 22K 1/8W J 0805 GS SMD Resistor 2M2 1/8W J 0805 GS SMD Resistor 2K7 1/8W J 0805 GS SMD Resistor 3K9 1/8W J 0805 GS SMD Resistor 39K 1/8W J 0805 GS SMD Resistor 470R 1/8W J 0805 GS SMD Resistor 4K7 1/8W J 0805 GS SMD Resistor 47K 1/8W J 0805 GS SMD Resistor 470K 1/8W J 0805 GS SMD Resistor 56K 1/8W J 0805 GS SMD REsistor 6K8 1/8W J 0805 R313,314,318,320 R89,90,140,150 R81,85,96,97,131,137,142,147,162,179 R75,83,92,98,132,133,151,156,163,164,183,82, R74,99 R95,141,148,181 R136,167 R134 R37 R87,93 R80,84,157 R130,161, R86,94 R91 R34,36,152,153 R35 R32,33 R38 R135,166

Qty Description

Reference Designator

PREAMP PCB

Resistors 024-000097-120ZS 024-100497-100ZS 024-100598-121ZS 024-150498-121ZS 024-150598-100ZS 024-200597-100ZS 024-220298-121ZS 1 GS SMD Resistor PN:1206J000 0R 1/4W J 1206 GS SMD Resistor PN:1206F102 1K 1/4W F 1206 GS SMD Resistor 10K 1/4W J 1206 GS SMD Resistor 1K5 1/4W J 1206 GS SMD Resistor 15K 1/8W F 0805 GS SMD Resistor PN:1206F203 20K 1/4W F 1206 GS SMD Resistor 22R 1/4W J 1206 R258,290,297,302,303, R238,264,288,291 R202,206,207,212,222,235,252-254,257,228,229,262,268,284 R251 R223, R256,208,209,231,232 R249

Part number PREAMP PCB

024-220397-120ZS 024-237598-120ZS 024-270498-121ZS 024-330397-120ZR 024-330498-121ZS 024-330598-121ZS 024-365697-100ZR 024-402597-100ZS 024-432598-100ZR 024-470598-121ZS 024-470698-121ZS 024-470797-100ZS 024-536597-100ZR 024-560598-121ZS 024-620398-121ZS 024-680498-121ZS 024-680598-121ZS 024-820598-121ZS 021-432598-100ZS 021-475498-100ZR 026-500495-005ZS 026-500595-267ZS Capacitors 031-100244-101ZS 031-100344-102AZS 031-100344-104AZS 031-220344-106AZS 031-270244-100ZR 031-270444-101 031-470144-101AZS 031-680144-100ZS 034-100515-304ZS 034-100615-301ZS 034-220516-301ZS 035-100343-300ZS 035-220243-100ZR 035-330293-300ZR 035-470353-302ZR 035-680253-300ZR 033-330515-300ZS Semiconductors 054-007200-100LZS 054-011400-100ZR 054-390402-100ZR 054-414803-100ZS 054-523701-100ZR 050-505200-001ZS 051-011100-100ZR Miscellaneous 072-010360-000ZR 072-040008-110ZS 074-030002-000ZR 074-030018-000ZR GR RCA JACK PN:B217CK GS Terminal housing PN:JS-1001-08 8P P:2.5 GR TOGGLE SW PN:L101-T2B4QE LFE, PHASE GR TOGGLE SW PN:L103-T2-B4 AUTO ON-OFF J201 P2 SW201,202 SWGS SMD IC: (JRC) M072M-DUAL OP-AMP GR SMD Transistor PN:DTC114TKA SMT3 (ROHM GR SMD Transistor (SC00044) PN:MMBT3904TR(Fairchild) GS SMD DIODE: PN:LL4148 MINI-MELF GR SMD ZENZER DIODE: (GMT) GMBZ5237B 8V2 SOT23 GS LED PN:LT-2402-21 GR JFET N-Channel PN:J111 TO-92 (FAIRCHILD U200-205 Q202 Q203,204 D201,204,207,209,212,216,218,219,405,413,414,217,203,200, D206 LED1 QGS SMD cap. 0u01/50V K 1206 X7R GS SMD cap. 0u1/50V K 1206 X7R GS SMD cap. 100pF/50V K NPO 1206 GS SMD cap. 220pF/50V K X7R 1206 GR SMD cap. 0u027/50V K 0805 X7R SMD cap. 2700pF/50V K 1206 X7R GS SMD cap. 0u0047/50V K 0805 X7R GS SMD cap. 0u0068/50V K 0805 X7R GS elec. Cap. 10uF/16V M (R)0511 P:2.5 TAPIN GS Elec. Cap. 100uF/16V M (R)0611 P:5 GS elec. Cap. 22uF/16V M (R)0511 P:2 GS PE Cap. 0uF1/50V J P:5 GR PE Cap. FE-M 0u022/63V J P:5m/m GR PE Cap. PN:ESK063S33JT 0u033/63V J P:5 GR PE Cap. P:5 0u47/63V J P/N:R82DC347DQJ GR PE Cap. FE-M PN:ESK063S68JT 0u068/63V J P:5mm GS NPE cap. 33uF/16V M (R)0511 P:2 C12,13 C227,229,230,232-235,200 C222 C215,216,204 C280 C224 C2G1,C281 C212 C220,237 C221 C223,416,14,15,411,415 C213 C202 C209,218 C207,208 C201 C214,1 GS SMD Resistor 220R 1/4W J 1206 GS SMD Resistor 23K7 1/8W F 0805 GS SMD Resistor 2K7 1/4W J 1206 GR SMD Resistor 330R 1/4W J 1206 GS SMD resistor 3K3 1/4W J 1206 GS SMD resistor 33K 1/4W J 1206 GR SMD resistor 365K 1/4W F 1206 GS SMD resistor 40K2 1/4W F 1206 GR SMD resistor 43K2 1/8W F 0805 TPAING GS SMD resistor 47K 1/4W J 1206 GS SMD resistor 470K 1/4W J 1206 GS SMD resistor 4M7 1/4W F 1206 GR SMD resistor 53K6 1/4W F 1206 GS SMD resistor 56K 1/4W J 1206 GS SMD resistor 620R 1/4W J 1206 GS SMD resistor 6K8 1/4W J 1206 GS SMD resistor 68K 1/4W J 1206 GS SMD resistor 82K 1/4W J 1206 GS Metal film 43K2 1/8W F GR MF resistor 4K75 1/8W F GS VR 5K PN:RD163111R22B-5K15A-EJ GAIN GS VR 50KBx4 PN:RD1631411001D-50KBx4 R255 R281 R237 R211,282 R240 R298,406,408,414 R285 R260 R214 R280 R259 R244,243 R283 R224 R221,226, R247 R250 R263 R214 R204 R216 R233

C410,418,427 C420-423, C419( in series with R403 T400 pin2-5) C424 C428,429 C417,401-403, C404-406 C414,413 C412 C407 C408 C223,416,14,15,411,415 C425,426
GR FUSIBLE RES 100R 1W J GS SMD resistor 9K1 1/8W J 0805 GS SMD resistor 470R 1/4W J 1206 GS SMD resistor PN:1206F103 10K 1/4W F 1206 GS SMD resistor 2K2 1/4W J 1206
R403(C419 in sereis with C403 T400 pin2-5) R413,415 R401,402 R409,416,417,405 R400
D400,402,403 D406-409 D404 Q406 Q408 Q404 Q402 BR400 U400
DAUGHTER PCB (Attached to Power PCB)
054-033904-100ZR 054-033906-100ZR 054-414803-100ZS 024-100598-120ZS 024-220298-120ZS 034-100444-300ZR 072-040337-000ZR 1 SMD (TRANSISTOR) PN:MMBT3904LT1G SOT23 ING SMD transistor (ON) PN:MMBT3906LT1G SOT23 ING GS SMD DIODE:PN:LL4148 MINI-MELF ING GS SMD resistor 10K 1/8W J 0805 ING GS SMD resistor 22R 1/8W J 0805 ING GR electrolytic cap. 1uF/50V K (R)0511 P:5 TAING HEADER Right Angle PN:211-110-000-400 10PIN Q403B Q405B D410B R404B,R407B R412B C430B CONNECT

MAIN PCB

Resistors 024-100498-120ZS 024-100598-120ZS 024-100698-120ZS 024-130598-120ZS GS SMD resistor 1K 1/8W J 0805 GS SMD resistor 10K 1/8W J 0805 GS SMD resistor 100K 1/8W J 0805 GS SMD resistor 13K 1/8W J 0805 R119 R1,4,7,16,121-123,126,128,138,165,168,170,125,143,169,19, R120 R118

Part number MAIN PCB

024-150598-100ZS 024-220298-121ZS 024-220498-121ZS 024-220598-120ZS 024-332498-100ZS 024-332598-101ZS 024-392498-100ZR 024-470398-120ZS 024-470598-120ZS 024-560298-120ZS 024-560498-120ZS 024-560598-120ZS 024-680498-120ZS Capacitors 031-100144-103ZS 031-100144-106ZS 031-100344-100ZS 031-100364-100ZS 031-100384-100RZS 031-220344-300ZS 031-470144-101ZS 031-470344-100ZS 034-100715-300ZS 034-330615-301ZS 032-100484-200ZS 033-330494-270ZS 033-680464-270ZS 034-820794-200ZR 034-100625-300ZS 034-220525-300ZR 034-220615-300ZS 034-220625-300ZS Resistors 021-100402-021ZS 022-005105-020ZS 020-220496-100ZS Semiconductors 054-000100-100ZS 054-008409-000ZR 054-033904-100ZR 054-033906-100ZR 054-290701-100ZR 054-414803-100ZS 054-540100-100ZR 054-555100-100ZR 051-359400-000ZR 051-290700-100ZR 051-540101-000ZR Miscellaneous 072-040039-000ZR 044-100100-000ZS 025-010300-000ZR 025-210100-000ZS 043-110300-000ZR 043-300101-000ZR 043-560200-000ZR 072-040007-000ZS 072-040008-110ZS 072-040064-000ZR 073-111003-000ZR 1 GR terminal (PCB TYPE) PC205 (t=0.8m/m) T205MA GS SMD FERRITE BEAD PN:321611 600R/100MHz 1206 GR thermister PN:NTSE103KZ072 K L:50mm GS thermister (PTC) PN:PTMS2101RP516Y GR COIL PN:YT-13141 110uHx210% GR INDUCTOR PN:YT-10033 30uH GR INDUCTOR 56uH YT-10779 GS terminal housing SWA101 PN:JS-1001-07 7P GS terminal housing PN:JS-1001-08 8P P:2.5 GR terminal (PCB TYPE) PC250 (t=0.8m/m) T250MA GR shorting strap 54.9x13.6x1mm TER402,403,406,407,TER2,4,8,3 FB1,2 TH1 TH2 L8 (L8+L11) L9,10 L12 P9 P1 T1,TER7 JGS SMD DIODE: PN:ES1D 200V 1A GR SMD ZENER DIODE:(PHILIPS) BZX84C3V0-7-F SOT-23 GR SMD (TRANSISTOR) PN:MMBT3904LT1G SOT23 GR SMD transistor (ON) PN:MMBT3906LT1G SOT23 GR SMD transistor (ON) PN:MMBT2907ALT1 SOT-23 GS SMD DIODE:PN:LL4148 MINI-MELF GR SMD transistor PNP (ON SEN) MMBT5401 LT1 SOT-23 GR SMD transistor (NPN) PN:MMBT5551 LT1R (ON) GR MOSFET N-CHANNEL PN:2SK3594-01SC (FUJI) GR Transistor PNP (ON) PN:MPS2907A RLRAR TO-92 GR Transistor PNP(FAIRCHILD PN:2N5401 TO-92 D23,37,40,44,47 D32 Q28,29,50,51,127,128,130 Q30,38 Q52 D1,4-6,21,22,31,33,34,38,41,45,48,53,54 Q1,2,26 Q25 Q11,13,15,17 Q12,14,16,18 QGS MOF resistor 1K 2W J FK TYPE GS resistor PN:SQM 0R05 5W J 25x13 GS film resistor 2K2 1/2W J R173,48 R2 R1 GS SMD cap. 0u001/50V K 0805 X7R GS SMD cap. 0u01/50V K 0805 X7R GS SMD cap. 0u1/50V K 0805 X7R GS SMD cap. 0u1/100V K 1206 X7R GS SMD cap. 0u1/250V K 1206 X7R GS SMD cap. 220pF/50V K 0805 NPO GS SMD cap. 0u0047/50V K 0805 X7R GS SMD cap. 470pF/50V K 0805 X7R GS elect. Cap. 1000uF/16V M (R)1017 P:3.5 GS elec. Cap. 330uF/16V M (R)0812 P:3.5 loose package GS END mylar cap. 1uF/250V K P:15 GS NPE cap. ELYTONE 3u3/63V K10 (R) 8x13 TBE GS NPE cap. ELYTONE 6u8/100V K10 (R)1020 GNE GR elec. Cap. (LP) 85 8200uF/80V M (R)3545 P:10 GS elect. Cap. 100uF/25V M (R)6.3x11 P:5 GR elec. Cap. 22uF/25V M (R)5x11 P:2.5 TAPIN GS elect. Cap. 220uF/16V M (R)0611 P:2.5 GS elec. Cap. 220uF/25V M (R)0812 P:5 C130 C27,28 C116 C5,6,69,112,115,135,138 C39B C40 C1G1 C123 C109,132 C32 C30,37,39,C31,38 C114,137 C113,136 C1,4 C62 C25,26 C8 CGS SMD resistor 15K 1/8W F 0805 GS SMD resistor 22R 1/4W J 1206 GS SMD resistor 2K2 1/8W J 0805 GS SMD resistor 22K 1/8W J 0805 GS SMD resistor 3K32 1/8W F 0805 GS SMD resistor 33K2 1/8W F 0805 GR SMD resistor 3K92 1/8W F 0805 GS SMD resistor 470R 1/8W J 0805 GS SMD resistor 47K 1/8W J 0805 GS SMD resistor 56R 1/8W J 0805 GS SMD resistor 5K6 1/8W J 0805 GS SMD resistor 56K 1/8W J 0805 GS SMD resistor 6K8 1/8W J 0805 R20,21 R28,29 R17,31,110,139 R127 R22 R60,60B R63 R145,155,177,186 R3,171 R24-27 R30 R15 R23