SOUNDPOINT SERIES SP5, SP6, SP6C, SP6CS, SP8, SP8C

OWNERS GUIDE

THANK YOU FOR CHOOSING JBL
For more than 50 years, JBL has been involved in every aspect of music and film recording and reproduction, from live performances to monitoring the recordings you play in your home, car or office. Were confident that the JBL loudspeakers you have chosen will provide every note of enjoyment that you expected and that when you think about purchasing additional audio equipment for your home, car or office, you will once again choose JBL. Please take a moment to register your product on our Web site at www.jbl.com. It enables us to keep you posted on our latest advancements, and helps us to better understand our customers and build products that meet their needs and expectations. JBL Consumer Products

INCLUDED

SP5, SP6, SP8 One pair of speakers with grilles. Template/paint shield. Remove paint shield (inner rectangle) at perforation.
SP6C, SP6CS, SP8C One pair of speakers with grilles (SP6C and SP8C). Model SP6CS includes only one loudspeaker, since it is capable of reproducing two channels of audio. Template/paint shield. Remove paint shield (inner circle) at perforation.

SPEAKER PLACEMENT

FRONT SPEAKERS

400 600

MODELS SP5, SP6, SP8 AS REAR SPEAKERS
MODELS SP6C, SP6CS, SP8C IN CEILING ble, they may be placed in a wall (or in the ceiling) behind the listening position, facing forward. The surround speakers should not call attention to themselves. They should provide a diffuse, ambient sound accompanying the main program material heard in the front speakers. In Dolby* Digital and DTS systems, aim the tweeters toward the listening position at ear-level height. MODEL SP6CS Model SP6CS has the capability of playing two channels through one loudspeaker, thanks to its dual-tweeter/dualvoice-coil construction. Since the tweeters are close together, in general they should be aimed away from each other for best coverage. For two-channel (stereo) applications, e.g., as a single speaker in a remote room of a distributed audio system, install the SP6CS speaker centrally in the ceiling for best stereo imaging, swiveling the tweeters so that one points toward the left and the other toward the right of the listening position, aimed at earlevel height. The SP6CS may also be used to play the left and right surround channels in a 5.1-channel home theater system, in which case it should be mounted in the ceiling slightly behind the listening position, centered from left to right and with the tweeters pointing toward the left and right of the listening position, aimed at ear-level height. For 7.1-channel systems where it is desired to use two SP6CS speakers, one to play both the left surround and surround back channels and the other to play both the right surround and surround back channels, mount each SP6CS speaker in the ceiling, slightly behind the listening position, one closer to the left side of the room and the other closer to the right side. Aim the tweeters away from each other, toward the front and rear of the room.
Proper placement of the speakers is an important step in obtaining the most realistic soundstage possible. These recommendations are for the optimum placement of the loudspeakers. Use these placement recommendations as a guide. Slight variations will not diminish your listening pleasure. The front speakers should be placed the same distance from each other as they are from the listening position. They should be placed at about the same height from the floor as the listeners ears will be, with the tweeters aimed toward the listener at ear-level height. In a home theater configuration, the two surround speakers should be placed slightly behind the listening position and ideally should face each other and be at a level higher than the listeners ears. If that is not possi-

SPEAKER CONNECTIONS

CONNECTION TIPS The wires for both speakers should be the same length. If one speaker is placed closer to the amplifier than the other, hide the excess wire behind the wall. Speakers and electronics terminals have corresponding (+) and () terminals. Most manufacturers of speakers and electronics, including JBL, use red to denote the (+) terminal and black for the () terminal. It is important to connect both speakers identically: (+) on the speaker to (+) on the amplifier and () on the speaker to () on the amplifier. Wiring out of phase results in thin sound, weak bass and a poor stereo image. With the advent of multichannel surround sound For model SP6CS, the terminals for both the left and right channels will systems, connecting all of the be on the same loudspeaker. speakers in your system with the correct polarity remains equally important in order to preserve the proper ambience and directionality of the program material. To use the push-type speaker terminals, press the red (+) or black () cap for the desired terminal, insert the bare end of the speaker wire into the hole below the cap and release the cap. Gently tug on the wire to make sure that it is fully inserted.

WIRE LENGTH

RECOMMENDED SIZE
Up to 20 ft. Up to 30 ft. Greater than 30 ft.
16 gauge 12 gauge 10 gauge

INSTALLATION

The SoundPoint Series in-wall speakers were designed to be easily installed. However, if you are unsure of your ability to properly install these loudspeakers, please contact your dealer or a qualified installer. TOOLS NEEDED

Pencil

Phillips #2 screwdriver

Measuring tape

Utility knife

Carpenters level

EXISTING CONSTRUCTION

SP5, SP6, SP8

1/2" 1/2" 1/2"
Remove the grille from the speaker frame by pulling on the paper tab. If the tab is missing, to avoid scratching the grille or baffle you may unfold a paper clip, insert the straight end through one of the holes in the grille, and gently pull up.
Determine the correct speaker location. Note: Remove the inner template, which is the paint shield, at the perforation. Use the outer template when cutting the drywall.

Note: Always allow at least one-half inch between a wall stud and the speaker cutout or the locking tabs will not be able to swivel into place.

Cut the drywall.

Connect the speaker wires to the speaker. The SoundPoint speakers feature unique swivel mounts for the tweeters that enable you to aim the very directional high frequencies toward the listening position, at ear-level height. Before installing the speaker grille, gently press on the outer edge of the tweeter mount to adjust the position of the tweeter. The tweeter will not swivel more than 15 degrees in any direction; do not attempt to force it to move further. You may also rotate the tweeter to orient the JBL logo as desired.
Place the frame assembly in the wall.
Screw down each of the four Phillips head screws. The locking tabs will swivel into place and secure the unit to the rear surface of the drywall.
Replace the metal grille.

SP6C, SP6CS, SP8C

Cut the drywall. Note: Always allow at least one-half inch between a wall stud and the speaker cutout or the locking tabs will not be able to swivel into place.
Connect the speaker wires to the speaker. Model SP6CS requires two sets of speaker wires, one for each channel.
The SoundPoint speakers feature unique swivel mounts for the tweeters that enable you to aim the very directional high frequencies toward the listening position, at ear-level height. Before installing the speaker grille, gently press on the outer edge of the tweeter mount to adjust the position of the tweeter. The tweeter will not swivel more than 15 degrees in any direction; do not attempt to force it to move further. You may also rotate 6
the tweeter to orient the JBL logo as desired. The dual tweeters of the SP6CS speaker may be swiveled independently. Optimum imaging will be obtained by aiming the tweeters to the left and right of the listening position, at ear-level height, if your application permits.

NEW CONSTRUCTION

You will need to purchase the correct rough-in frame kit for your model:
SPEAKER MODEL ROUGH-IN FRAME KIT
SP5 SP6 SP6C SP6CS SP8 SP8C
RIF5 RIF6 RIF6C RIF6CS RIF8 RIF8C
Detailed installation instructions are supplied with the rough-in kit.
PAINTING THE SPEAKER FRAME AND GRILLE
SoundPoint Series loudspeakers can be painted to match any decor. If you wish to change their color, the satin finish on the grille and frame will function as a primer coat. Before painting, install the paint shield (inner section of template in the assembly kit) securely into the recess in the baffle. This will protect the speaker components and baffle from paint residue. Use a high-quality spray paint, and apply a thin coat of color. Be certain the grille perforations remain free of paint. Filling them with paint will diminish the sound quality. Note: Gently remove the acoustical foam blanket from the grille before painting. Reattach the blanket after the paint has dried.

TROUBLESHOOTING

IF THERE IS NO SOUND FROM ANY OF THE SPEAKERS:
sure none of the speaker wires are frayed, cut, punctured or touching each other.
IF THERE IS LOW (OR NO) BASS OUTPUT:
Check that receiver/amplifier is on and a source is playing. Check all wires and connections between receiver/amplifier and speakers. Make sure all wires are connected. Make sure none of the speaker wires are frayed, cut, punctured or touching each other. Review proper operation of your receiver/amplifier.
IF THERE IS NO SOUND COMING FROM ONE SPEAKER:
owners manual for futher information on correct speaker configuration in Dolby Digital, DTS and other surround sound modes.
IF THE SYSTEM PLAYS AT LOW VOLUMES BUT SHUTS OFF AS VOLUME IS INCREASED:
Make sure the connections to the left and right Speaker Inputs have the correct polarity (+ and ). Consider adding a powered subwoofer to your system. In Dolby Digital or DTS modes, make sure your receiver/ processor is correctly configured. When using a subwoofer, make sure the subwoofer output of the receiver/ processor has been enabled. If no subwoofer is being used, make sure the left and right front and rear speakers have been configured as LARGE. See your receiver/processors
Check all wires and connections between receiver/amplifier and speakers. Make sure all wires are connected. Make sure none of the speaker wires are frayed, cut , punctured or touching each other. If more than one pair of main speakers is being used, check the minimum-impedance requirements of your receiver/amplifier. 7
Check the Balance control on your receiver/amplifier. Check all wires and connections between receiver/amplifier and speakers. Make sure all wires are connected. Make

SPECIFICATIONS

Frequency Response 45Hz 20kHz (10dB) Recommended Maximum Amplifier Power 60 watts Impedance 8 ohms nominal Sensitivity 87dB (2.83V/1m) Crossover Frequency 3,000Hz Woofer 5-1/4" titanium-laminate cone w/rubber surround Tweeter 1"titanium-laminate dome, w/Elliptical Oblate Spheroidal waveguide and swivel mount Plate Size (W x H) 7-1/2" x 10" (191mm x 254mm) Mounting Cutout Size (W x H) 6-1/8" x 8-11/16" (156mm x 221mm) Mounting Depth 3-3/4" (95mm) Weight per Speaker 4 lb (1.8kg)

Frequency Response 38Hz 20kHz (10dB) Recommended Maximum Amplifier Power 80 watts Impedance 8 ohms nominal Sensitivity 88dB (2.83V/1m) Crossover Frequency 2,800Hz Woofer 6-1/2" titanium-laminate cone w/rubber surround Tweeter 1"titanium-laminate dome, w/Elliptical Oblate Spheroidal waveguide and swivel mount Plate Size (W x H) 8-1/2" x 11" (216mm x 279mm) Mounting Cutout Size (W x H) 7-1/8" x 9-11/16" (181mm x 246mm) Mounting Depth 3-7/8" (98mm) Weight per Speaker 5 lb (2.3kg)
Frequency Response 40Hz 20kHz (10dB) Recommended Maximum Amplifier Power 80 watts Impedance 8 ohms nominal Sensitivity 88dB (2.83V/1m) Crossover Frequency 2,600Hz Woofer 6-1/2" titanium-laminate cone w/rubber surround Tweeter 1" titanium-laminate dome, w/swivel mount Plate Size (Diameter) 9-3/16" (233mm) Mounting Cutout Size (Dia.) 7-7/8" (200mm) Mounting Depth 4-1/4" (108mm) Weight per Speaker 4.5 lb (2.0kg)
Frequency Response 40Hz 20kHz (10dB) Recommended Maximum Amplifier Power 100 watts total (50WPC) Impedance 8 ohms nominal per input Sensitivity 88dB (2.83V/1m), both channels driven Crossover Frequency 2,600Hz Woofer 6-1/2" titanium-laminate cone w/rubber surround Tweeters Dual 3/4" titanium-laminate domes, w/swivel mounts Plate Size (Diameter) 9-3/16" (233mm) Mounting Cutout Size (Dia.) 7-7/8" (200mm) Mounting Depth 4-1/4" (108mm) Weight per Speaker 4 lb (1.8kg)
Frequency Response 30Hz 20kHz (10dB) Recommended Maximum Amplifier Power 100 watts Impedance 8 ohms nominal Sensitivity 89dB (2.83V/1m) Crossover Frequency 2,400Hz Woofer 8" titanium-laminate cone w/rubber surround Tweeter 1"titanium-laminate dome, w/Elliptical Oblate Spheroidal waveguide and swivel mount Plate Size (W x H) 10-1/8" x 13-1/8" (257mm x 333mm) Mounting Cutout Size (W x H) 8-7/8" x 11-13/16" (225mm x 300mm) Mounting Depth 4" (102mm) Weight per Speaker 7.8 lb (3.5kg)
Frequency Response 32Hz 20kHz (10dB) Recommended Maximum Amplifier Power 100 watts Impedance 8 ohms nominal Sensitivity 89dB (2.83V/1m) Crossover Frequency 2,400Hz Woofer 8" titanium-laminate cone w/rubber surround Tweeter 1"titaniumlaminate dome, w/swivel mount Plate Size (Diameter) 10-7/8" (275mm) Mounting Cutout Size (Dia.) 9-1/2" (240mm) Mounting Depth 4-1/4" (108mm) Weight per Speaker 5.6 lb (2.5kg)
Declaration of Conformity
All features and specifications are subject to change without notice. The maximum recommended amplifier power rating will ensure proper system headroom to allow for occasional peaks. We do not recommend sustained operation at these maximum power levels. * Trademark of Dolby Laboratories. DTS is a registered trademark of Digital Theater Systems, Inc.
We, Harman Consumer International 2, route de Tours 72500 Chateau-du-Loir France declare in own responsibility that the products described in this owners manual are in compliance with technical standards: EN 61000-6-3:2001 EN 61000-6-1:2001

Gary Mardell Harman Consumer International Chateau-du-Loir, France 5/04

PRODUCT LINE:

PRO SOUND COMES HOME
JBL Consumer Products 250 Crossways Park Drive, Woodbury, NY Balboa Boulevard, Northridge, CA 91329 516.255.4JBL (4525) www.jbl.com
NOTE: For new-construction applications, be sure to purchase the correct rough-in frame kit.

SOUNDPOINT SERIES

MODELS:
SP5, SP6, SP6C, SP6CS, SP8, SP8C
DESIGN GOAL: Combine the superior performance of traditional JBL loudspeakers with the convenience of in-wall installation. TWEETER TYPE: Titanium-laminate-dome with swivel mount WOOFER TYPE: Titanium-laminate cone with rubber surround CROSSOVER NETWORK: Straight-Line Signal Path (SSP)
2004 Harman International Industries, Incorporated JBL is a registered trademark of Harman International Industries, Incorporated. Part No. 406-000-05033 5/04
PROFESSIONAL REFERENCE: Studio Monitor

S P E C I F I C AT I O N S
Frequency Response 45 20kHz (10dB) Recommended Maximum Amplifier Power 60 watts Impedance 8 ohms nominal Sensitivity 87dB (2.83V/1m) Crossover Frequency 3,000Hz Woofer 5-1/4" titanium-laminate cone w/rubber surround Tweeter 1" titanium-laminate dome, w/Elliptical Oblate Spheroidal waveguide and swivel mount Plate Size (W x H) 7-1/2" x 10" (191mm x 254mm) Mounting Cutout Size (W x H) 6-1/8" x 8-11/16" (156mm x 221mm) Mounting Depth 3-3/4" (95mm) Frequency Response 38 20kHz (10dB) Recommended Maximum Amplifier Power 80 watts Impedance 8 ohms nominal Sensitivity 88dB (2.83V/1m) Crossover Frequency 2,000Hz Woofer 6-1/2" titanium-laminate cone w/rubber surround Tweeter 1" titanium-laminate dome, w/Elliptical Oblate Spheroidal waveguide and swivel mount Plate Size (W x H) 8-1/2" x 11" (216mm x 279mm) Mounting Cutout Size (W x H) 7-1/8" x 9-11/16" (181mm x 246mm) Mounting Depth 3-7/8" (98mm)
Frequency Response 40 20kHz (10dB) Recommended Maximum Amplifier Power 80 watts Impedance 8 ohms nominal Sensitivity 88dB (2.83V/1m) Crossover Frequency 3,000Hz Woofer 6-1/2" titanium-laminate cone w/rubber surround Tweeter 1" titanium-laminate dome, w/Elliptical Oblate Spheroidal waveguide and swivel mount Plate Size 9-3/16" (233mm) Mounting Cutout Size 7-7/8" (200mm) Mounting Depth 4-1/4" (108mm)
Frequency Response 30 20kHz (10dB) Recommended Maximum Amplifier Power 100 watts Impedance 8 ohms nominal Sensitivity 89dB (2.83V/1m) Crossover Frequency 2,000Hz Woofer 8" titanium-laminate cone w/rubber surround Tweeter 1" titanium-laminate dome, w/Elliptical Oblate Spheroidal waveguide and swivel mount Plate Size (W x H) 10-1/8" x 13-1/8" (257mm x 333mm) Mounting Cutout Size (W x H) 8-7/8" x 11-13/16" (225mm x 300mm) Mounting Depth 4" (102mm)
All features and specifications are subject to change without notice. The maximum recommended amplifier power rating will ensure proper system headroom to allow for occasional peaks. We do not recommend sustained operation at these maximum power levels. * Trademark of Dolby Laboratories. DTS is a registered trademark of Digital Theater Systems, Inc.
Declaration of Conformity
We, Harman Consumer International 2, route de Tours 72500 Chateau-du-Loir France declare in own responsibility, that the products described in this owners manual are in compliance with technical standards: EN 50081-1:1992 EN 50082-1:1997 Luc E. Godard Harman Consumer International Chateau-du-Loir, France 8/01

OWNERS GUIDE

PRODUCT LINE: MODELS:

PRO SOUND COMES HOME

JBL Consumer Products 250 Crossways Park Drive, Woodbury, NY Balboa Boulevard, Northridge, CA 91329 800-336-4JBL (4525) (USA only) www.jbl.com NOTE: For new-construction applications, be sure to purchase the correct rough-in frame kit. 2001 JBL, Incorporated. JBL is a registered trademark of JBL, Incorporated. Part No. 170-0035
SoundPoint Series SP5, SP6, SP6C, SP8
D E S I G N G O A L : Combine the superior performance of traditional JBL loudspeakers with the convenience of in-wall installation. T W E E T E R T Y P E : Titanium-laminate-dome with EOS waveguide, and swivel mount W O O F E R T Y P E : Titanium-laminate cone with rubber surround C R O S S O V E R N E T W O R K : Straight-Line Signal Path (SSP) P R O F E S S I O N A L R E F E R E N C E : Studio Monitor
X + 0 + YM HZ X + 0 + YM HZ

X + 0 + Y M HZ

D E S I G N G O A L : Combine the superior performance of traditional JBL loudspeakers with the convenience of in-wall installation. T W E E T E R T Y P E : Titanium-laminate dome with EOS waveguide, and swivel mount W O O F E R T Y P E : Titanium-laminate cone with rubber surround C R O S S O V E R N E T W O R K : Straight-Line Signal Path (SSP) P R O F E S S I O N A L R E F E R E N C E : Studio Monitor
THANK YOU FOR CHOOSING JBL
For more than 50 years, JBL has been involved in every aspect of music and film recording and reproduction, from live performances to monitoring the recordings you play in your home, car or office. Were confident that the JBL loudspeakers you have chosen will provide every note of enjoyment that you expected and that when you think about purchasing additional audio equipment for your home, car or office, you will once again choose JBL. Please take a moment to complete the enclosed profile card. It enables us to keep you posted on our latest advancements, and helps us to better understand our customers and build products that meet their needs and expectations. JBL Consumer Products

INCLUDED

SP5, SP6, SP8
One pair of speakers with grille.
Template/paint shield (punch out at perforation).

SPEAKER PLACEMENT

Front Speakers

400- 600

Models SP5, SP6, SP8 as Rear Speakers

Model SP6C in Ceiling

Proper placement of the speakers is an important step in obtaining the most realistic soundstage possible. These recommendations are for the optimum placement of the loudspeakers. Use these placement recommendations as a guide. Slight variations will not diminish your listening pleasure. The front speakers should be placed the same distance from each other as they are from the listening position. They should be placed at about the same height from the floor as the listeners ears will be. In a home theater configuration, the two surround speakers should be placed slightly behind the listening position and, ideally, should face each other and be at a level higher than the listeners ears. If that is not possible, they may be placed in a wall behind the listening position, facing forward. The surround speakers should not call attention to themselves. They should provide a diffuse, ambient sound accompanying the main program material heard in the front speakers.

SPEAKER CONNECTIONS

Connection Tips
The wires for both speakers should be the same length. If one speaker is placed closer to the amplifier than the other, hide the excess wire behind the wall. Speakers and electronics terminals have corresponding (+) and () terminals. Most manufacturers of speakers and electronics, including JBL, use red to denote the (+) terminal and black for the () terminal. It is important to connect both speakers identically: (+) on the speaker to (+) on the amplifier and () on the speaker to () on the amplifier. Wiring out of phase results in thin sound, weak bass and a poor stereo image. With the advent of multichannel surround-sound systems, connecting all of the speakers in your system with the correct polarity remains equally important in order to preserve the proper ambience and directionality of the program material.
Front or Rear Speaker Outputs
Wire Length Up to 20 ft. Up to 30 ft. Greater than 30 ft.
Recommended Size 16 gauge 12 gauge 10 gauge

I N S TA L L AT I O N

The SoundPoint Series in-wall speakers were designed to be easily installed. However, if you are unsure of your ability to properly install these loudspeakers, please contact your dealer or a qualified installer.

Tools Needed

Pencil

Phillips #2 screwdriver

Measuring tape

Utility knife

Carpenters level

EXISTING CONSTRUCTION

1/2" 1/2" 1/2"

Template

Remove the grille from the speaker frame.
Determine the correct speaker location.
Note: Always allow at least one-half inch between a wall stud and the speaker cutout or the locking tabs will not be able to swivel into place.

Cut the dry wall.

Connect the speaker wires to the speaker.
Place the frame assembly in the wall.
Screw down each of the four Phillips head screws. The locking tabs will swivel into place and secure the unit to the rear surface of the drywall.
Replace the metal grille.
Determine the correct speaker location. Note: Always allow at least one-half inch between a wall stud and the speaker cutout or the locking tabs will not be able to swivel into place.

Cut the drywall.

Screw down each of the three Phillips head screws. The locking tabs will swivel into place and secure the unit to the rear surface of the drywall.

NEW CONSTRUCTION

You will need to purchase the correct rough-in frame kit for your model: Speaker Model SP5 SP6 SP6C SP8 Rough-in Frame Kit RIF5 RIF6 RIF6C RIF8
Detailed installation instructions are supplied with the rough-in kit.
PA I N T I N G T H E S P E A K E R FRAME AND GRILLE
SoundPoint Series loudspeakers can be painted to match any decor. If you wish to change their color, the satin finish on the grille and frame will function as a primer coat. Before painting, install the paint shield (in the assembly kit) securely into the recess in the baffle. This will protect the speaker components and baffle from paint residue. Use a high-quality spray paint, and apply a thin coat of color. Be certain the grille perforations remain free of paint. Filling them with paint will diminish the sound quality. Note: Gently remove the acoustical foam blanket from the grille before painting. Reattach the blanket after the paint has dried.

TROUBLESHOOTING

If there is no sound from any of the speakers: Check that receiver/amplifier is on and a source is playing. Check all wires and connections between receiver/amplifier and speakers. Make sure all wires are connected. Make sure none of the speaker wires are frayed, cut or punctured. Review proper operation of your receiver/amplifier. If there is no sound coming from one speaker: Check the Balance control on your receiver/amplifier. Check all wires and connections between receiver/amplifier and speakers. Make sure all wires are connected. Make sure none of the speaker wires are frayed, cut or punctured. If there is low (or no) bass output: Make sure the connections to the left and right Speaker Inputs have the correct polarity (+ and ). Consider adding a powered subwoofer to your system. In Dolby* Digital or DTS modes, make sure your receiver/processor is correctly configured. When using a subwoofer, make sure the subwoofer output of the receiver/processor has been enabled. If no subwoofer is being used, make sure the left and right front and rear speakers have been configured as LARGE. See your receiver/processors owners manual for futher information on correct speaker configuration in Dolby Digital, DTS and other surround-sound modes. If the system plays at low volumes but shuts off as volume is increased: Check all wires and connections between receiver/amplifier and speakers. Make sure all wires are connected. Make sure none of the speaker wires are frayed, cut or punctured. If more than one pair of main speakers is being used, check the minimum-impedance requirements of your receiver/amplifier.