Installation

Contents

Installation.. 2 Before You Begin Installation. 2 Tools and Supplies Needed. 2 Speaker Requirements. 2 Adapters for Easier Installation.. 2 Connections. 3 Crimp Connections.. 3 Upgrading your System. 3 Disconnect Battery. 4 Remove Old Radio. 4 Install Half-sleeve. 5 Wiring.. 5
How to Install the CR560X AM/FM Stereo Radio/Cassette Tape Player
Install half-sleeve (page 5)
Final Installation (page 10)

AS/P S BAN D VOL CD

LOUD MUT E MON O DISP 5 6
Install wiring (pages 6 and 7)

1 CH BAS

Connect and test radio (pages 8 and 9)
Welcome! What you're holding in your hands is no ordinary owner's manual. We've tried to make the instructions in this book clear and easy to follow. For your Jensen stereo to work right, it must be installed correctly. This manual will show you how to install your new stereo like a pro. It's a good idea to read all of these instructions before you begin the installation. Most installations are straightforward and can be handled by a do-it-yourselfer with the right tools, patience, and the ability to follow instructions. But, do-it-yourself installation isn't for everyone. If you still don't feel confident after reading this book, consider turning the installation job over to someone better suited to it. Warranty Service If your Jensen stereo should ever require service, you will need to have the original dated receipt. If you ever need to return the unit for any reason, always include the receipt with the product.
Fuse Adapters.. 5 Cars with a Single Speaker Wire.. 5 Wiring with a Wiring Adapter. 6 Connect Wires. 6 Install Wiring Inside the Car.. 6 Wiring DiagramAdvanced Installation.. 7
Testing.. 8 Reconnect Battery.. 8 Test Power Wiring. 8 Test Antenna Connection. 8 Test Memory Wiring.. 8 Set the Clock.. 8 Test Speaker Connections. 9 Final Installation.. 10 Final InstallationISO-DIN. 10 Troubleshooting.. 11 Removing Radio from Dash. 11 Securing Wires. 11 Specifications and Warranty. 12

Technical Assistance

For technical assistance with the installation of the CR560X, call 1-800-323-0221.

5588 CR560X_EIN.p65

2/29/00, 10:46 PM

CR560X

Before You Begin Installation
Before you begin, you will need tools, supplies and adapters. It is best to make sure you have everything you need before you take your dashboard apart.
Tools and Supplies Needed

Basic Installation:

Flat and Phillips screwdrivers Wire cutter Wire stripper Tools to remove existing radio (screwdriver, socket wrench set or other tools) Radio removal tool Electrical tape
Adapters for Easier Installation
Electrical and dashboard adapters make installation easier. Purchase adapters from your local Jensen retailer, electronics store or car stereo specialty store.

Wiring Harness Adapter

For a basic installation, you can purchase a wiring harness adapter for your car's existing radio connectors. This makes installation easy.

Advanced Installation:

Soldering iron Crimping tool Volt meter or 12 volt test light Solder Crimp connectors 14-18 gauge wire for power connections Speaker wire

Dashboard Adapters

The opening in your dashboard may not match the size of your Jensen radio. Purchase an adapter kit for your car.

Antenna Adapter (GM cars)
1990 and newer GM cars have a small antenna connector. You will need an adapter when installing this radio in a newer GM car.

Speaker Requirements

Only connect the CR560X to speakers rated in the load impedance range of 4 to 8 ohms. Speakers with a load impedance less than 4 ohms could damage the CR560X.

CR560X Professional Tip

Connections
Good wire connections are very important for best sound and long-term reliability. Here are two methods:

Professional Tip

Crimp Connections
Purchase crimp connectors and crimping tool. Connectors are color coded. This Jensen radio uses RED connectors (18-20 gauge wire). 1. Strip 1/4 inch (6mm) of insulation from both wires. 2. Insert into connector. 3. Crimp tightly. You can make permanent splices (using butt connectors) or select connectors that can be removed and reinstalled.

Strip Wire 1/4' (6mm)

Splice 1. Strip 1/2 inch (12 mm) of insulation from both wires. 2. Wrap wires together 3. Fold wires over 4. Stretch electrical tape tightly over splice.
Splice Strip Wire 1/2" (12mm)
Solder Rosin core solder Heat wires not solder Soldering iron
Solder Solder is the best way to connect wires, but it takes skill and practice. Splice the wires (as shown above). Before taping, heat the wires (not the solder). When the wires are hot enough, touch the solder to the splice. The solder will flow over the wires. Stretch electrical tape tightly over splice. Important: Be very careful when soldering wires in your car. Cover nearby carpeting and seats to prevent damage from hot solder.

Upgrading Your System

International Jensen makes a wide range of car stereo products that will make your car system sound better, great or INCREDIBLE!
Better Sound Install a Jensen tape deck or CD player like youre doing now. High power units can make your existing speakers sound better and play louder. Great Sound Replace your existing speakers with Jensen speakers. Many of our speakers will fit into your car without cutting or drilling. You can also add an amplified graphic equalizer to tailor the sound to your liking. INCREDIBLE Sound Jensen offers a full line of amplifiers, highpower speakers and subwoofers that can turn your car into audio dynamite. You can go loud, louder and loudest by selecting Jensen components from your retailer.

Disconnect Battery

Before you begin, always disconnect the battery negative terminal.

Remove Old Radio

Your original car radio is installed in one of four ways, depending on the car.

Bracket Mounted

1. Remove dashboard faceplate 2. Unscrew brackets 3. Disconnect wiring harness and remove radio

Removal Tool

Some cars use a special removal tool to release the radio. 1. Insert the tool(s) 2. Pull out the radio 3. Disconnect wiring harness and remove radio

4x25W JensenAuto Revers Plus Tuner e
Replacing an Aftermarket Radio
Use a screwdriver to bend tabs completely out of the way. Pull sleeve from dashboard. The sleeve should fit tightly and may be damaged unless you remove it carefully.

ISO-DIN

1. Remove trim to expose DIN chassis. 2. Remove the ISO-DIN frame from the dashboard. 3. Unscrew screws from the sides. 4. Disconnect wiring harness and remove radio.

Bend Tabs Flat

Pull Sleeve Out Caution: Edges are sharp. Use a rag or wear a glove.

COMPACT

DIGITAL AUDIO

RGCD 400

8 X OVERS AMPLIN G.

15 WATTS

PWR BASS MO/ST DISP LO/DX INT RPT RDM BAND CD VOL SEL VOL

Install Half-sleeve

Not needed for ISO-DIN (Japanese vehicle) installation.

Support Strap (supplied)

Half-sleeve (supplied)

Adapter (optional)

1. Install adapter if necessary. Install halfsleeve into adapter from front of dash. It will be a tight fit.
2. Bend over tabs where possible to secure half-sleeve to adapter or inside of dash. 3. Install strap to strut under dash. Secure strap to an existing screw.

Wiring

Important If wiring connections are made wrong, the unit will not operate properly and it could be damaged. Follow the installation instructions carefully, or have the installation handled by an experienced technician.

Fuse Adapters

No convenient power wire? Install a fuse adapter having a spade connector.

Fuse Adaptor

Crimp on a matching connector and attach: Yellow wireFuse marked MAIN, BAT or PWR Red wireFuse marked ACCY (accessory), or RADIO
Wiring with a Wiring Adapter
This is the easiest wiring method, because it replaces your existing radio. You will have to buy a wire harness adapter from your dealer, a car stereo installation shop or electronics store. If you use a wiring adapter, you can connect all wires to the radio before you even start to take your old radio out.

Connect Wires

Splice, crimp or solder the wires from the Jensen connector to the wiring adapter. Match the wires according to the chart (below) and the wiring adapter instructions.
Splices You can make all these connections without even being in the car.
Install Wiring Inside the Car
1. Connect wiring adapter to the car's existing wiring harness. 2. Connect antenna extender cable to car antenna lead. 3. Slide radio part way into half-sleeve.

1 Car Wiring Harness

Antenna Extender Cable

Car Antenna Lead

Wiring Adapter (attach to car wiring harness)

Wiring Color Codes

Function LF Speaker LF+ Speaker LR Speaker LR+ Speaker RF Speaker RF+ Speaker RR Speaker RR+ Speaker Power Antenna Ground Ignition Battery Color white/black white green/black green gray/black gray violet/black violet dark blue black red yellow

Go to Testing on page 8.

Wiring DiagramAdvanced Installation
If you are installing new speakers or amplifiers or replacing an aftermarket installation, use this diagram.
Back of Radio Antenna Jack
RCA-to-RCA cables Amplifier wiring (not supplied) (See amplifier instructions) Red AMP White

Dark Blue

Power Antenna Connect to power antenna or amplifier. If not used, tape bare end of wire.
Turn on for amps Filter Box
Ground Connect to ground terminal or clean, unpainted metal part of chassis.

In-line Fuse (5 amp)

Yellow
Memory Connect to battery or 12 volt power source that is always live. The radio will not store time or station presets if this wire is not connected.
Accessory Connect to existing radio wire or radio fuse. The radio will not work if this wire is not connected.

In-line Fuse (.5 amp)

LF white/black white LF+ LR green/black green LR+
RF gray/black gray RF+ RR violet/black violet RR+
When replacing a fuse, make sure new fuse is correct type and amperage. Using an incorrect fuse could damage radio. The CR560X uses two fuses with in-line fuse holders as part of rear wiring harness: 5 amp fast blow AGC (yellow wire). .5 amp fast blow AGC (red wire). Go to Testing on page 8.

Testing

Before you finish the installation, you should do the following tests to make sure the wiring is correct and everything is operating properly.

Reconnect Battery

When wiring is complete, reconnect the battery negative terminal.

Test Memory Wiring

Test Power Wiring
1. Turn ignition switch on. Press the (Power) button to turn the radio on. The display should light and show the radio display. If not, check the electrical connection at the yellow and red wires. 2. If equipped, the power antenna should also operate. If not, check electrical connections to the dark blue wire.
1. With the radio playing, hold button 1 for two seconds. CH 1 will appear on the display. You just stored the current station in memory. 2. Turn the key off, then turn the key on again. 3. The radio should resume playing at the same station and volume. If not, make sure the yellow wire is connected properly.

Set the Clock

Press DISP button to display the clock.

Test Antenna Connection

1. Press DISP button for three seconds until display flashes. 2. Press to change minutes, to change hours.
1. Hold a tuning button for more than two seconds. The radio should tune to a nearby station. If not, check antenna connection. 2. Press + to increase volume until you can hear the radio playing.

Test Speaker Connections

These tests make sure the speakers are connected right. If speakers dont play at all, both wires may not be connected. If the wrong speaker plays (you hear front speakers when you expect rear speakers) make sure you connected the wires right.

Balance

SEL SEL SEL SEL

SEL SEL SEL SEL SEL

1. Press SEL four times. 2. Hold the + button until the display shows BA.r 10. Only the right speakers should be playing. If not, check the wiring. Make sure you connected the wires just like the chart on page 6.
5. Press SEL five times. 6. Hold the + button until the display shows FA.F 10. Only the front speakers should be playing. If not, check the wiring. Make sure you connected the wires just like the chart on page 6.
3. Press SEL four times again. 4. Hold the button until the display shows BA.L 10. Only the left speakers should be playing. If not, check the wiring. Make sure you connected the wires just like the chart on page 6.
7. Press SEL five times again. 8. Hold the button until the display shows FA.r 10. Only the rear speakers should be playing. If not, check the wiring. Make sure you connected the wires just like the chart on page 6.
Once everything is operating correctly, perform Final Installation on page 10.

Final Installation

1. 2. 3. 4. Slide radio chassis into half-sleeve Secure to strap using nut Install faceplate by fitting left edge into position then pushing right edge closed. Reinstall any items you removed from the dashboard.

Nut (supplied)

MON O DISP
Final InstallationISO-DIN
1. 2. 3. 4. 5. Remove trim ring from front of radio. Trim ring is not needed for this type of installation. Mount factory brackets on new radio using existing screws from old radio. Slide radio and frame into dash opening and secure. Install dash panels previously removed. Install faceplate by fitting left edge into position then pushing right edge closed.

Troubleshooting

Problem
Does not operate (radio does not light)
No power to red wire (12V with key on) Inline fuse blown

Corrective Action

Check connection Check vehicle fuse Replace fuse Connect speaker wires Check all splices and connections Check splices, insulate all bare wires Insulate wire Insulate wire Install fuse of correct rating Call Jensen Technical Assistance (1-800-323-0221)
No speakers operate (radio lights normally) Not all speakers operate
Speaker wires not connected Incorrect splices or connections Speaker wires shorting to chassis ground or to each other

Blows fuses

Power wire shorting to ground Speaker wires shorting to ground Incorrect fuse

Cant find cause of problem

Removing Radio from Dash

Securing Wires
Be proud of your installation! Use wire ties to bundle wires together when possible. (But never bundle speaker wires and power wires together!)

PWR AMS BAN D VOL CD

Removal Key
Secure loose wires to the car to make sure they dont rub or rattle.
1. Remove faceplate. 2. Remove trim ring by gently pulling up on the middle of the trimming to release the plastic snaps. 3. Insert removal keys between radio and dash trim to depress locking springs. Pull radio out of dash.

Specifications

FM Tuner Tuning range.... 87.5 MHz-107.9 MHz FM mono sensitivity..... 12 dBf 50 dB quieting sensitivity (stereo).... 16 dBf Stereo separation @ 1 kHz.... 40 dB AM Tuner Tuning range.... 530 kHz-1710 kHz Amplifier Total system power..... 100 Watts peak Power output.... front: 2 x 25 Watts rear: 2 x 25 Watt Tape Frequency response..... 50 Hz-14KHz Wow & flutter.....15% JIS Channel separation....35db@1 KHZ Signal to noise ratio (a-weighted)..... 55db General Power supply.... 11-16 VDC, negative ground Speaker output impedance.... 4-8 Ohms Fuses.... fast blow AGC (.5 amp and 5 amp) Specifications subject to change without notice.
Limited One Year WarrantyUSA and Canada
Length of Warranty. This warranty from Recoton Mobile Electronics shall be in effect for a period of one year from the date of the first consumer purchase. Persons Protected. This warranty will be enforceable by the original owner and any subsequent owners during the warranty period so long as proof of date of purchase from an authorized Jensen dealer is presented whenever warranty service is required. What is Covered. Except as otherwise specified below, this warranty covers all defects in material and workmanship in this product. The following are not covered: damage resulting from accident, misuse, abuse, neglect, product modification, improper installation, incorrect line voltage, unauthorized repair or failure to follow instructions supplied with the product; damage occurring during shipment (claims must be presented to the carrier); elimination of car static or other electrical interferences; any product purchased outside USA or Canada, or on which the serial number has been defaced, modified or removed. How You Can Get Service. U.S. Purchasers. Please telephone Jensen at 1-800-323-4815. We will either inform you of the name and address of an authorized Jensen repair station which will service the product or will advise you to send the product to a factory service center. Canadian Purchasers. The product should be returned to the Jensen dealer from whom it was purchased and such dealer either will service or arrange for service of the product. If shipment of the product is required, it should be packed securely. The original dated bill of sale must always be included with the product as proof of warranty coverage. What We Will Pay For. We will pay for all labor and material expenses required to repair the product, but you must pay any labor costs for the removal and/or installation of the product. If the product is shipped for warranty service, you must prepay the initial shipping charges, but Jensen will pay the return shipping charges if the product is returned to an address inside the USA or Canada. Limitation of Implied or Statutory Warranties and Conditions. All implied or statutory warranties and conditions, including warranties or conditions of merchantability, fitness for particular purposes and non-infringement, are limited in duration to the length of this warranty. Exclusion of Certain Damages. Jensens liability is limited to the repair or replacement, at our option, of any defective product and shall not include incidental or consequential economic damages of any kind. Some states and/or provinces do not allow limitations on how long an implied warranty lasts and/or do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations and exclusions may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state and province to province.