Before you get started

Congratulations on purchasing this IMPRESSA. To ensure that your IMPRESSA works smoothly, please read these instructions for use carefully and keep them as a future reference. If you need more information or if you experience any problems which are not covered in enough detail in these instructions for use, please contact your local stockist or ourselves.
The IMPRESSA may only be operated by instructed persons. People, including children, who do not have the physical, sensory or mental capabilities to use the machine safely or are inexperienced or lack knowledge in how to use the machine safely must be supervised by a responsible person when using it, or must be instructed in how to use it correctly. Never start up a defective IMPRESSA or an IMPRESSA with a damaged supply cable. In the event of signs of damage, for example if there is a smell of burning, unplug the machine immediately from the mains supply and contact JURA service. If the mains cable of this machine is damaged, it must be repaired either directly by JURA or by an authorised JURA service centre. Never repair or open the IMPRESSA yourself. Repairs and modifications to the machine may only be undertaken by authorised JURA service centres using genuine spare parts and accessories. The machine contains live parts. If opened, there is a danger of potentially fatal injury. Do not immerse the IMPRESSA in water.
1. Safety instructions 1.1 Proper use
The machine is designed and intended for private domestic use. It should only be used for coffee preparation and to heat milk and water. Use for any other purpose will be deemed improper. JURA Elektroapparate AG cannot accept any responsibility for the consequences of improper use. Before using the machine read these instructions for use thoroughly and completely and comply with the instructions they contain. Keep these instructions for use close to the machine and pass them on to the next user.

1.3 Precautions

Never subject the IMPRESSA to environmental influences (rain, snow, frost) and do not operate with wet hands. Place the IMPRESSA on a sturdy, horizontal surface resistant to any water leaks. Never place on hot or warm surfaces (hobs). Select a site out of reach of children.

CLOSE TAP SYSTEM FILLING HEATING PRESS RINSE (3).
Close the steam / hot water draw-off tap (14).
3. Using for the first time
Fill the bean container with coffee beans (12). Switch your IMPRESSA on with the On/Off button SPRACHE DEUTSCH (21).
Press the Maintenance button The machine rinses. RINSING READY
The illuminated ring (2) is active. Turn the Rotary Switch (1) until the desired language appears on the display. Now confirm your selection by pressing the Rotary Switch (1). FILL WATER TANK
If FILL BEANS appears on the display, again press any coffee preparation button. The grinder is not yet filled with coffee beans. To get a really good crema you can individually adjust the height-adjustable coffee spout (17) to your cup sizes (Fig. 3).
Remove the water tank (10) and fill with fresh water. Refit the water tank in your IMPRESSA. OPEN TAP Place receptacle under the Professional Cappuccino Frother (15) (Fig. 10). Now open the steam / hot water draw-off tap (14) (Fig. 13). SYSTEM FILLING
4. Adjusting the water hardness
Water is heated in the IMPRESSA. Over time this will result in calcification and this is displayed automatically. The IMPRESSA must be set to the hardness of the water used. Use the test strips provided. 1 German hardness corresponds to 1.79 French hardness. When the filter is activated, the water hardness programme item disappears.
The IMPRESSA is set to 16 dH by default. You can change this setting. Proceed as follows: READY Press and hold the Rotary Switch (1) until RINSE appears on the display. The illuminated ring (2) is active. Turn the Rotary Switch (1) until the following message appears on the display: HARDNESS 16 dH Now press the Rotary Switch (1) to enter the programme item. Now turn the Rotary Switch (1) until the desired water hardness appears. For example OK HARDNESS 20 dH. Confirm the desired water hardness by pressing the Rotary Switch (1).

5.1 Inserting the filter

Press and hold the Rotary Switch (1) until RINSE appears on the display. The illuminated ring (2) is active. Turn the Rotary Switch (1) until the following message appears on the display: FILTER NO Press the Rotary Switch (1) again to enter this programme item. Turn the Rotary Switch (1) until the following message appears on the display: YES OK INSERT OPEN TAP Press the Rotary Switch (1) to activate the filter cartridge.
Remove and empty the water tank (10). Fold up the filter holder. Insert the filter cartridge in the water tank, exerting slight pressure (Fig. 1). Close the filter holder until it audibly snaps into place. Fill the water tank with cold, fresh mains water and reinsert the tank. Place a sufficiently large receptacle (around 1 litre) under the Professional Cappuccino Frother (15) (Fig. 10). Open the steam / hot water draw-off tap (14) (Fig. 13). FILTER RINSING

7. Adjusting the amount of water for coffee
The figure in ML is approximate and may vary from the actual amount. The machine automatically doubles the amount of water programmed for the 2 espressi / 2 coffees preparation buttons. You can also change the amount of water during operation. Turn the Rotary Switch (1) during the brewing operation until the desired ML figure appears on the display. You can stop the drawing off of water prematurely by pressing any button. It is easy to permanently adjust the amount of water for all speciality coffees, milk specialities and hot water to the cup size. As in the following example, adjust the amount of water or milk once and then this amount will be used each time you prepare this speciality coffee. Example: Permanent setting of amount of water for one espresso: READY Press the 1 ESPRESSO preparation button and hold down until the following message appears on the display. 1 ESPRESSO ENOUGH COFFEE ?

1 ESPRESSO READY

8. Preparing 1 cup of coffee
You can change the strength at any time before or during the grinding operation by turning the Rotary Switch (1). You can choose from 4 strengths ( MILD / NORMAL / STRONG / XSTRONG). You can stop preparation at any time by pressing any preparation button. READY (6). Place 1 cup under the height-adjustable coffee spout (17). Press the 1 coffee preparation button 1 COFFEE The illuminated ring (2) is active. You can adjust the desired strength for the current coffee preparation by turning the Rotary Switch (1) during the grinding operation. 1 COFFEE
You can adjust the desired amount of water for the current coffee preparation by again turning the Rotary Switch (1) during the brewing operation. For example 100 ML. Turn the Rotary Switch (1) until the desired amount of water appears on the display. For example 110 ML.
Press the button again as soon as there is enough coffee in your cup. OK

1 COFFEE READY

2 COFFEES READY
Your speciality coffee is prepared.
10. Preparing preground coffee
Never use water-soluble instant coffee or instant coffee. We would recommend always using powder from freshly ground coffee beans or preground, vacuum-packed coffee. Never add more than 2 portions of powder. The filler shaft is not designed for storage. Ensure that the preground coffee you are using is not ground too fine. This may block the system and the coffee will then only be dispensed in drips. If you have added too little powder, the NOT ENOUGH PREGROUND message appears on the display. The IMPRESSA aborts the operation, ejects the preground coffee and resets the machine so that it is ready to brew coffee. You can interrupt preparation prematurely by pressing any preparation button. READY Place 1 or 2 cups under the height-adjustable coffee spout (17). Open the cover of the filler funnel for preground coffee (11). FILL PRE-GROUND

9. Preparing 2 cups of coffee
The strength cannot be selected when preparing 2 cups of coffee. You automatically prepare 2 mild cups. You can stop preparation prematurely by pressing any preparation button. READY (7). Place 2 cups under the height-adjustable coffee spout (17). Press the 2 coffees preparation button 2 COFFEES The illuminated ring (2) is active. You can adjust the desired amount of water for the current coffee preparation by turning the Rotary Switch (1) during the brewing operation. The modified ML value relates to 1 cup. For example 100 ML. Turn the Rotary Switch (1) until the desired amount of water appears on the display. For example 110 ML.
Place 1 or 2 level measuring spoons of preground coffee into the filler funnel for preground coffee (11) (Fig. 11) and close the cover. SELECT BUTTON
Select the 1 coffee preparation button tion button (7). 1 COFFEE
(6) or 2 coffees prepara-
If necessary adjust the amount of water saved by turning the Rotary Switch (1). For example 200 ML.
The illuminated ring (2) is active. By turning the Rotary Switch (1), you can individually select the amount of water for coffee: For example 110 ML. 1 COFFEE READY
Once the desired amount of water is reached, the following appears on the display: CLOSE TAP READY Due to the system design, some water may be released before the TAP is closed. Close the steam / hot water draw-off tap (14).

12. Preparing steam

To obtain a perfect water flow, fit the removable hot water nozzle (Fig. 5). Do not change the removable hot-water nozzle (16) immediately after drawing off water because it will be hot and there will be a danger of burns. When drawing off water, sputtering may occur at the start. Avoid direct contact with the skin. The steam function is used to prepare milk foam and hot milk and for cleaning the Professional Cappuccino Frother (15). If the optional 2-stage frothing nozzle is fitted, the steam function can be used to heat liquids and produce foam. Make sure that the nozzle is fitted correctly when preparing steam. If the nozzle becomes blocked with particles of milk residue or is incorrectly assembled, it may disengage and come off while the frother is in use. Due to the system design, some water will escape at first when stream is drawn off. However, this will not affect the result in any way. When drawing off , sputtering may occur at the start. The nozzle gets hot during operation. Avoid direct contact with the skin.

11. Preparing hot water

Place a cup under the removable hot-water nozzle (16) (Fig. 5). Open the steam / hot water draw-off tap (14) (Fig. 13). The illuminated ring (2) is active. WATER

READY (8). HEATING READY

Press the steam preselection button
Due to the system design, some steam may be released before the tap is closed. There is a danger of scalding.
Open the steam / hot water draw-off tap (14) (Fig. 13) to draw off steam. The illuminated ring (2) is active. STEAM
13. Professional Cappuccino Frother 13.1 Preparing cappuccino with the Professional Cappuccino Frother
Cappuccino is made up of one third espresso, one third warm milk and one third milk foam. The Professional Cappuccino Frother (15) is used for preparing the milk portion. When steam is drawn off, a negative pressure is created and this draws milk with the aid of the Professional Cappuccino Frother (15) and produces milk foam. You can also heat up milk by turning the selector switch on the Professional Cappuccino Frother to the Milk position (Fig. 20). To avoid malfunctions, the Professional Cappuccino Frother (15) must be cleaned regularly. Make sure that the nozzle is fitted correctly. If the nozzle becomes blocked with particles of milk residue or is incorrectly assembled, it may disengage and come off while the frother is in use. When using for the first time, remove the protective cover from the Professional Cappuccino Frother (Fig. 6). The protective cover is used only during transport to protect the nozzle against contaminant ingress. Remove the milk pipe from the Welcome Pack and connect it to the Professional Cappuccino Frother.
You can adjust the steam preparation time individually by turning the Rotary Switch (1) until the desired number of SEC appear on the display. For example 25 SEC.
If you do not change the steam preparation time on the Rotary Switch (1), you prepare the saved amount of steam. Once the amount of steam is reached, the following message appears on the display: CLOSE TAP READY The machine is ready to prepare steam for around 40 sec., then the machine is reset so that it is ready to brew coffee. You can prematurely stop steam preparation at any time by closing the steam / hot water draw-off tap (13). Close the steam / hot water draw-off tap (14).

Insert the other end of the milk pipe into a milk carton or connect it to a milk container (Fig. 7). Place a cup under the Professional Cappuccino Frother (Fig. 7). The high-quality stainless steel container is a practical addition for all lovers of milk specialities. It keeps the milk cool throughout the day and is fully in keeping with the design of your IMPRESSA. All original JURA accessories are available from stockists. Turn the selector switch on the Professional Cappuccino Frother to the Milk Foam position (Fig. 18). READY (8). HEATING READY Press the steam preselection button
Adjust the steam preparation time to suit the size of your cup. Once the amount of steam is reached, the following message appears on the display: CLOSE TAP READY The machine is ready to prepare steam for around 40 sec., then the machine is reset so that it is ready to brew coffee. You can prematurely stop steam preparation at any time by closing the steam / hot water draw-off tap (14). Due to the system design, some steam and milk may be released before the tap is closed. There is a danger of scalding. Now, move your cup with the milk foam under the coffee spout and draw off the desired speciality coffee (Fig. 8). Your cappuccino is ready. Close the steam / hot water draw-off tap (14).
Open the steam / hot water draw-off tap (Fig. 13) to draw off steam. The milk foam is prepared. The illuminated ring (2) is active. STEAM
13.2 Preparing hot milk with the Professional Cappuccino Frother
Turn the selector switch on the Professional Cappuccino Frother to the Milk position (Fig. 20). The operation for preparing hot milk is the same as that for preparing milk foam for a cappuccino (see chapter 13 Preparing cappuccino with the Professional Cappuccino Frother).
If you do not change the steam preparation time on the Rotary Switch (1), you prepare the saved amount of steam.
13.3 Rinsing the Professional Cappuccino Frother
To ensure that the Professional Cappuccino Frother (15) works perfectly, you should rinse it with water after every milk preparation. Your IMPRESSA will not prompt you to rinse the Professional Cappuccino Frother. READY Remove the milk pipe from the milk carton or the milk container. Fill a receptacle with fresh water and immerse the milk pipe in it. Place a receptacle under the Professional Cappuccino Frother and move the selector switch to the Milk foam or Milk position. Press the steam preselection button HEATING READY (8).
13.4 Dismantling and rinsing the Professional Cappuccino Frother
Carefully remove the Professional Cappuccino Frother (15) from your IMPRESSA by twisting slightly. Dismantle the Professional Cappuccino Frother (15) into its individual parts (Fig. 16). Rinse all frother parts thoroughly under running water. Re-assemble the frother and refit it on your IMPRESSA.

Rotary Switch Permanent settings in programming mode always follow the same model. To enter programming mode, press the Rotary Switch (1) until RINSE appears on the display. By turning the Rotary Switch (1) you can change the set values and select different programme items. By pressing the Rotary Switch (1) you can view values or save selected values. You can select and adapt the following programme items to your needs:
Programme item Sub-item RINSE RINSE FILTER (only appears if filter is activated) CLEAN DE-SCALE (only appears if filter is not activated) EXIT SELECT BUTTON EXIT NO YES INACTIVE dH Explanation Select the desired maintenance programme. If no action is taken, programming mode is exited automatically after approximately five seconds. For more information, please refer to chapters 6 and 16 to 18.
Programme item Sub-item OFF AFTER 15 MIN to 15 HRS
Explanation Set the number of hours after which the IMPRESSA should switch off automatically. Set whether the switch-on rinse should be started manually or automatically. Reset the settings for individual products, all products or the entire machine to the factory setting. Keep track of all prepared speciality coffees and milk specialities and view the maintenance status.

RINSING

MANUAL AUTOMATIC PRODUCT ALL PROD. RESET ALL EXIT BUTTONS CLEAN FILTER (only appears if filter is activated) DE-SCALE (only appears if filter is not activated) VERSION EXIT ML OZ DEUTSCH ENGLISH FRANCAIS ITALIANO NL ESPANOL PORTUGUES

BUTTONS

Select your settings for speciality coffees, milk specialities and hot water. Indicate whether you want to operate your IMPRESSA with or without a CLARIS filter cartridge. Adjust the water hardness.

DISPLAY LANGUAGE

Select the unit for the amount of water. Select your language.

FILTER /

HARDNESS (only appears if filter is not activated)

ENERGY / SAVE SAVE

Select an energy-saving mode.
15.1 Buttons programme item
With the BUTTONS programme item you can enter individual settings for all speciality coffees, milk and hot water. Permanent settings in programming mode always follow the same model. The following permanent settings can be made for speciality coffees, milk and hot water:
Product 2 espressi 1 coffee 2 coffees Milk Amount of water Strength 25 ML 240 ML 25 ML 240 ML SEC Temperature NORMAL, HIGH NORMAL, HIGH 1 espresso 25 ML 240 ML MILD, NORMAL, STRONG, XSTRONG NORMAL, HIGH 25 ML 240 ML MILD, NORMAL, STRONG, XSTRONG NORMAL, HIGH

Press the preparation button for the speciality coffee for which you want to adjust the amount of water. For example, 1 COFFEE. WATER 100 ML. 110 ML. Press the Rotary Switch (1). For example For example OK WATER Turn the Rotary Switch (1) to adjust the amount of water as desired. Press the Rotary Switch (1) to save the new amount of water.
Turn the Rotary Switch (1) further until the next sub-item appears on the display: STRENGTH NORMAL Press the Rotary Switch (1). Turn the Rotary Switch (1) until the following message appears on the display: STRONG OK STRENGTH Press the Rotary Switch (1) to save the change.

Hot water 25 ML 450 ML

For example: Proceed as follows to change the amount of water for a coffee from 100 ML to 110 ML, to change the strength from NORMAL to STRONG and the temperature from NORMAL to HIGH. Press the Rotary Switch (1) until the following message appears on the display: RINSE Turn the Rotary Switch (1) again until the following message appears on the display: BUTTONS SELECT BUTTON Press the Rotary Switch (1).
Turn the Rotary Switch (1) further until TEMPERATURE appears on the display. Press the Rotary Switch (1). NORMAL
Turn the Rotary Switch (1) to adjust the temperature. HIGH OK TEMP. Press the Rotary Switch to confirm your selection.
15.4 Energy programme item
The IMPRESSA is equipped with the new On/Off button (21) (= Zero-Energy Switch). This allows the machine to be fully disconnected from the mains. An Energy Save Mode (E.S.M.) can also be permanently set. READY Press and hold the Rotary Switch (1) until RINSE appears on the display. The illuminated ring (2) is active. Turn the Rotary Switch (1) until ENERGY appears on the display. Press the Rotary Switch (1). SAVE Turn the Rotary Switch (1) until the following message appears on the display: SAVE OK ENERGY Press the Rotary Switch (1) again to confirm the change.
Turn the Rotary Switch (1) until EXIT appears on the display. Press the Rotary Switch (1). SELECT BUTTON
Turn the Rotary Switch (1) again until EXIT appears on the display. Press the Rotary Switch (1). BUTTONS Turn the Rotary Switch (1) again until EXIT appears on the display. Press the Rotary Switch (1) to exit programming mode. READY
15.2 Filter programme item

For details, please refer to chapter 5.1 Inserting the filter.
Turn the Rotary Switch (1) until EXIT appears on the display.
15.3 Water hardness programme item
For details, please refer to chapter 4 Adjusting the water hardness.
Press the Rotary Switch (1) to exit programming mode. READY
15.5 Automatic switch-off time programme item
You can program when your IMPRESSA is to switch off. Select a time between 15 min. and 15 hrs.
Press and hold the Rotary Switch (1) until RINSE appears on the display. The illuminated ring (2) is active. Press the Rotary Switch (1) until you reach the OFF AFTER programme item. OFF AFTER Press the Rotary Switch (1) to enter the OFF AFTER programme item. 1 HRS Turn the Rotary Switch (1) to set the number of hours after which the machine is to switch off. For example 2 HRS. Press the Rotary Switch (1) to save the new automatic switch-off time. OK OFF AFTER
Press and hold the Rotary Switch (1) until RINSE appears on the display. The illuminated ring (2) is active. Turn the Rotary Switch (1) until RINSING appears on the display. Press the Rotary Switch (1). MANUAL Turn the Rotary Switch (1) until the following message appears on the display: AUTOMATIC OK RINSING Press the Rotary Switch (1) again to confirm the change.
Turn the Rotary Switch (1) until EXIT appears on the display. Press the Rotary Switch (1) to exit programming mode. READY
Turn the Rotary Switch (1) until the following message appears on the display. EXIT READY Press the Rotary Switch (1) again to exit programming mode.
15.7 Reset programme item
In the RESET programme item you can reset various settings to their factory settings: PRODUCT The settings (amount of water, strength, temperature) for any product can be reset individually to the factory settings. The corresponding double product is reset to the factory settings at the same time. ALL PROD. The settings (amount of water, strength, temperature) for all products are reset to the factory settings.
15.6 Rinse programme item
You can set whether the rinse should be started manually or automatically when switching on. READY
RESET ALL All customer settings are reset to the factory settings. The IMPRESSA then switches off.

Turn the Rotary Switch (1) again until EXIT appears on the display. Press the Rotary Switch (1) to exit programming mode. READY
For example you want to reset the values for one product to the factory setting: READY Press and hold the Rotary Switch (1) until RINSE appears on the display. The illuminated ring (2) is active. Turn the Rotary Switch (1) until RESET appears on the display. Press the Rotary Switch (1). PRODUCT SELECT BUTTON OK SELECT BUTTON By again pressing the appropriate preparation button, you can reset other speciality coffees to their factory setting. SELECT BUTTON Press the Rotary Switch (1).
15.8 Information programme item
In the INFORMATION programme item you can view the following information: Total coffee preparations Number of speciality coffees prepared, number of coffee powder, hot water and steam preparations Maintenance status and number of maintenance programmes performed (cleaning, descaling, changing the filter) and information relating to the software version READY Press and hold the Rotary Switch (1) until RINSE appears on the display. The illuminated ring (2) is active. Turn the Rotary Switch (1) until INFO appears on the display. Press the Rotary Switch (1). BUTTONS XXXX (=total number of speciality coffees prepared). To view the number of product preparations, press the preparation button of the desired speciality coffee. For example, to view the number of 1 COFFEE preparations. Press the Rotary Switch (1) again.
Press any preparation button, e.g. 1 ESPRESSO.
Press the Rotary Switch (1) to exit the PRODUCT programming item. Turn the Rotary Switch (1) until EXIT appears on the display. Press the Rotary Switch (1).
Press the 1 COFFEE preparation button. XXXX (=total number for 1 COFFEE) BUTTONS Turn the Rotary Switch (1) for more information about the filter, descaling or the machine version. Turn the Rotary Switch (1) until CLEAN appears on the display for example. Press the Rotary Switch (1) to view the number of cleaning operations performed. formed) Turn the Rotary Switch (1) until the following message appears on the display: In addition to the number of maintenance programmes performed, the progress bar also shows you the current maintenance status. When the bar is completely filled, your IMPRESSA will request the respective maintenance programme. Press the Rotary Switch (1) to exit the CLEAN programme item. CLEAN Turn the Rotary Switch (1) until EXIT appears on the display. Press the Rotary Switch (1). INFO Turn the Rotary Switch (1) again until EXIT appears on the display. XXXX (=total number of cleaning operations per Press the Rotary Switch (1) to exit the programme item.
Press the Rotary Switch (1) again. Press the Rotary Switch (1) once more. READY
15.9 ML/OZ display programme item
READY Press and hold the Rotary Switch (1) until RINSE appears on the display. The illuminated ring (2) is active. Turn the Rotary Switch (1) until DISPLAY appears on the Press the Rotary Switch (1). ML OZ. Turn the Rotary Switch (1) and select the desired setting. For example OK DISPLAY Press the Rotary Switch (1) to save the desired setting.

Top up the beans as described in chapter 2.4. The FILL BEANS display only goes out after a coffee has been prepared. We recommend that you clean the bean container with a dry cloth from time to time before refilling. Switch the IMPRESSA off to do this.

16.5 Changing the filter

After drawing off 50 litres of water, the filter will cease to work. You will be prompted to change the filter. For details, please refer to chapter 5.2 Changing the filter.
16.8 General cleaning instructions
When cleaning never use objects, pan cloths or cleaning sponges which may scratch the machine or corrosive chemicals. Wipe the inside and outside of the housing with a soft, damp cloth. Always clean the removable hot-water nozzle after use. To ensure that the Professional Cappuccino Frother always works properly, you should rinse it with water after every milk preparation.
To ensure that the Professional Cappuccino Frother always works properly, you should clean it daily when you have been preparing milk. The water tank should be rinsed daily and filled with fresh water. If you can see scale starting to form in the water tank, you can use a conventional descaling agent to remove it. Remove the water tank to do this (Fig. 4). When using a Claris filter cartridge, remove this before descaling the tank.
Close the steam / hot water draw-off tap (14). Press the On/Off button (21) to switch off your IMPRESSA.

17. Cleaning

The IMPRESSA machine comes with an integrated Cappuccino cleaning programme. The operation lasts about 15 minutes. Your stockist can supply original JURA cleaning tablets which are optimised for the cleaning programme of your IMPRESSA. We would like to point out that using unsuitable cleaning tablets may damage your machine and leave traces in the water. Once started, the cleaning operation must not be interrupted. The filler funnel for preground coffee must be cleaned after every cleaning programme (11). READY CLEAN (3) until the following message

16.9 Emptying the system

This operation is needed to protect the IMPRESSA from frost damage during transport. READY (8). HEATING READY Press the steam preselection button
Press the Maintenance button appears: EMPTY TRAY TRAY MISSING

Empty the drip tray.

Remove and empty the water tank. Allow all the steam to exit the nozzle until the system is empty. CLOSE TAP
Carefully reinsert the drip tray. Remove the cup grille (19).

Place a 1 litre receptacle (Fig. 12) under the height-adjustable coffee spout (17). PRESS RINSE (3). CLEANING ADD TABLET

18. Descaling

The IMPRESSA machine comes with an integrated descaling programme. The operation lasts about 40 minutes. Your stockist can supply original JURA descaling tablets which are optimised for the descaling programme of your IMPRESSA. We would like to point out that using unsuitable descaling tablets may damage your machine and leave traces in the water. The display will indicate when the IMPRESSA needs descaling. You can still prepare coffee or hot water/steam and run the descaling programme later on. Once started, the descaling operation must not be interrupted. When using the descaling agent, immediately clean up any splashes or drips on sensitive surfaces, especially natural stone and wooden surfaces. Alternatively take appropriate precautions. Always wait until all the added descaling agent has been used and the tank is empty. Never top up the descaling agent. READY DE-SCALE (3) until the following message
Add the tablet to the powder shaft (Fig. 15). Close the powder shaft. PRESS RINSE (3). CLEANING EMPTY TRAY TRAY MISSING HEATING READY
Remove and empty the drip tray.

Reinsert the drip tray.

Remove the Professional Cappuccino Frother (15) (Fig. 17). Press the Maintenance button appears: EMPTY TRAY
Once the cleaning operation is complete, use a dry cloth to rub down the powder shaft. Cleaning is complete.

Empty the drip tray.

TRAY MISSING AGENT IN TANK
Rinse the water tank thoroughly and fill it with cold fresh mains water. Then refit in the IMPRESSA. OPEN TAP DE-SCALING CLOSE TAP
Carefully reinsert the drip tray.
Open the steam / hot water draw-off tap (14) (Fig. 13).
Remove and empty the water tank. Completely dissolve the contents of one blister (3 tablets) in 0.5 litres of water and add the mixture to the water tank. Reinsert the water tank. OPEN TAP AGENT IN TANK
Once you have closed the steam / hot water draw-off tap (14), the following appears on the display: DE-SCALING EMPTY TRAY TRAY MISSING READY
Place a sufficiently large receptacle under the hot-water spout (Fig. 17). Open the steam / hot water draw-off tap (14) (Fig. 13). DE-SCALING CLOSE TAP DE-SCALING EMPTY TRAY TRAY MISSING FILL WATER TANK
Carefully reinsert the drip tray. Descaling is complete.

19. Disposal

Please dispose of old machines in an environmentallyneutral way Old machines contain valuable, recyclable materials which should be recycled. Please therefore dispose of old machines via suitable collection systems.

20. Tips for a perfect coffee
Height-adjustable coffee spout (17) You can adjust the coffee spout to the size of your cups (Fig. 3). Consistency of grind For details, please refer to chapter 2.5 Adjusting the grinder Prewarming cups You can prewarm the cups with hot water or steam. The smaller the amount of water for coffee, the more important the prewarming process. Sugar and cream Heat will be lost when you stir the product in your cup. Adding cream or milk from the fridge greatly lowers the temperature of the coffee.

21. Messages

Cause FILL WATER TANK The water tank is empty The float is defective FILL BEANS The bean container is empty Even though the beans have been topped up, the display does not go out EMPTY GROUNDS Coffee grounds container full Drip tray inserted too soon after emptying TRAY MISSING READY CLEAN READY DE-SCALE READY FILTER ERROR Drip tray not inserted correctly or missing Cleaning needed Descaling needed Filter has ceased working General fault Remedy Fill the water tank Rinse or descale the water tank Fill with beans Prepare a cup of coffee. The Fill beans message only disappears after you have prepared a coffee Empty coffee grounds container Wait 10 sec. before inserting drip tray Insert correctly Perform cleaning operation (chapter 17) Perform descaling operation (chapter 18) Change filter (chapter 5.2) Disconnect IMPRESSA from mains Have IMPRESSA checked by JURA customer support You will find contact details for your country at www.jura.com.

22. Problems

Problem Very loud grinder noise Cause Foreign object in grinder Remedy Coffee preparation with preground powder still possible Have IMPRESSA checked by JURA customer support Too little foam when producing milk foam Professional Cappuccino Frother is dirty Clean the Professional Cappuccino Frother (chapter 13) Check how the Professional Cappuccino Frother is put together Adjust grinder to coarser setting Use a coarser preground coffee
Individual parts of Professional Cappuccino Frother are not correctly assembled Coffee only dispensed in drips Consistency of grind too fine Preground coffee too fine
High-frequency electromagnetic interference may affect the display. Coffees can be still prepared. If you have not been able to remedy messages or problems, please contact your stockist or JURA Elektroapparate AG.