The IMPRESSA J7 Manual

The IMPRESSA Manual has been awarded the seal of approval by the independent German Technical Inspection Agency, TV SD, due to its easy-to-understand style, its thoroughness and coverage of safety aspects.

Table of contents

Your IMPRESSA J7
IMPORTANT SAFEGUARDS Control elements Proper use For your safety The IMPRESSA J7 Manual 13 Symbol description.... IMPRESSA JConnector System....15 JURA on the internet....15 Knowledge Builder.....Preparing and using for the first time 16 Supplied as standard.....16 Setting up.....16 Filling the water tank.....16 Filling the bean container.....17 First-time use....17 Inserting and activating the filter....18 Determining and adjusting the water hardness...19 Adjusting the grinder....20 Switching on.....21 Switching off.... Familiarising yourself with the control options 23 Preparation at the touch of a button... 23 One-off settings before and during preparation...24 Permanently setting the amount of water for the cup size...26 Permanent settings in programming mode...Preparation at the touch of a button 29 Ristretto, espresso and coffee....29 Cappuccino.....30 Pre-ground coffee.....31 Foaming and heating milk with the Professional Cappuccino Frother.. 32 Foaming milk with the Easy Cappuccino Frother... 33 Hot water.....34
Permanent settings in programming mode 35 Products.....35 Energy-saving mode.....36 Automatic switch-off..... 37 Rinsing.....38 Restore factory settings.....38 Viewing information and maintenance status...39 Unit for amount of water.....40 Language.....Maintenance 42 Maintenance tips.....42 Rinsing the machine.....42 Changing the filter....43 Cleaning the machine.....45 Descaling the machine....46 Rinsing the cappuccino frother....48 Cleaning the cappuccino frother....49 Dismantling and rinsing the Professional Cappuccino Frother...51 Dismantling and rinsing the Easy Cappuccino Frother...51 Cleaning the bean container.....51 Descaling the water tank.....Display messages Troubleshooting Transport and environmentally neutral disposal 57 Transport / Emptying the system.... 57 Disposal.....Technical data 58 Index 59 JURA contact details / Legal information 64

Important Safeguards

IMPORTANT SAFEGUARDS
These safeguards apply for machines with UL safety test (see rating plate and chapter 10, Technical data). Follow the basic safety precautions When using electrical appliances, basic safety precautions should always be followed, to reduce the risk of fire, electric shock, and/or injury to persons, including the following: Z Read all instructions. Z Do not touch hot surfaces. Use handles or knobs. Z To protect against fire, electric shock and injury to persons, do not immerse cord, plugs, or body of machine in water or other liquid. Z Close supervision is necessary when any appliance is used by or near children. Z Unplug from outlet when not in use and before cleaning. Allow to cool before putting or taking off parts, and before cleaning the appliance. Z Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions, or has been damaged in any manner. Return appliance to the nearest authorized service facility for examination, repair or adjustment. Z The use of accessory attachment not recommended by the appliance manufacturer may result in fire, electric shock, or injury to persons. Z Do not use outdoors. Z Do not let the cord hang over the edge of a table or counter, or touch hot surfaces. Z Do not place on or near a hot gas or electric burner, or in a heated oven. Z Always attach plug to appliance first, then plug cord into the wall outlet. To disconnect, turn any control to OFF then remove plug from wall outlet. Z Do not use appliance for other than intended use. Z Use extreme caution when dispensing hot steam. Z For household use only.

Control elements

Figure: IMPRESSA J7 Piano Black
Bean container cover Water tank cover Bean container with aroma preservation cover Water tank Height- and width-adjustable coffee spout Coffee grounds container Drip tray
Filler funnel for pre-ground coffee Grinder adjustment switch Storage compartment cover Storage compartment with measuring spoon for pre-ground coffee and hot water nozzle Connector System for removable frothers and nozzles Professional Cappuccino Frother Power switch and mains cable (side of machine) Cup platform
Surface of the machine: 1 Q On/off button 2 Rotary Switch 3 c Maintenance button
Front: 4 Display. Start symbol u Ristretto symbol i Espresso symbol o Coffee symbol ; Mild : Normal _ Strong m Hot water symbol n Steam symbol
The Connector System permits the use of different frothers and nozzles. These are available from stockists. Easy Cappuccino Frother Professional Cappuccino Frother Hot water nozzle

Important information

Proper use
The machine is designed and intended for private domestic use. It should only be used for coffee preparation and to heat milk and water. Use for any other purpose will be deemed improper. JURA Elektroapparate AG cannot accept any responsibility for the consequences of improper use. Before using the machine always read this manual thoroughly and completely and comply with the instructions it contains. Keep this IMPRESSA Manual close to the machine and pass it on to the next user if applicable.

For your safety

Please carefully read and observe the important safety information set out below. To avoid danger of potentially fatal electric shock: Z Never use a machine which is damaged or has a defective mains cable. Z In the event of signs of damage, for example if there is a smell of burning, unplug the machine immediately from the mains supply and contact JURA service. Z If the mains cable of this machine is damaged, it must be repaired either directly by JURA or by an authorised JURA service centre. Z Make sure that the IMPRESSA and the mains cable are not located close to hot surfaces. Z Be careful to ensure that the mains cable does not get caught and does not rub against sharp edges. Z Never open and repair the machine yourself. Do not modify the machine in any way that is not described in the IMPRESSA Manual. The machine contains live parts. If opened, there is a danger of potentially fatal injury. Repairs may only be carried out by authorised JURA service centres, using original spare parts and accessories.

You are holding the manual for your IMPRESSA J7 in your hand. It will help you to familiarise yourself with your IMPRESSA safely and quickly and teach you the full range of facilities it offers: Z Chapter 2, Preparing and using for the first time, explains step-by-step how to set up and prepare the machine. Z Chapter 3, Familiarising yourself with the control options is important for you to read as you are familiarising yourself with your IMPRESSA. Z All the other chapters are intended to help you when you have a specific query. @ You can download the short operating instructions for your machine from the JURA website (www.jura.com).

Symbol description

Warnings

CAUTION

Always take note of any information marked with the words CAUTION or WARNING and a warning sign. The signal word WARNING draws your attention to potential serious injury, and the signal word CAUTION to potential minor injury. CAUTION draws your attention to potential damage to the machine.
Symbols used E @ T Information and tips to make it even easier to use your IMPRESSA. References to the JURA website, which provides further information that may be of interest to you: www.jura.com Prompt to take action. This symbol means that you are being prompted to perform some action. Display message

1 IMPRESSA J7

IMPRESSA J7
The uncompromising all-round design of the IMPRESSA J7 indulges the eyes as well as the taste buds. Gourmets will find plenty to delight them as their coffee dreams come true and they experience a new dimension of enjoyment with ristretto, espresso, coffee crme, cappuccino, latte macchiato and many other trendy specialities. This is easy to achieve, because the innovative operating concept leaves nothing to be desired when it comes to simplicity. And the integrated cup illumination places every speciality coffee in the right light. Z Breathtakingly beautiful: Clear, no-frill contours and highquality materials set the tone of the design of the IMPRESSA J series. All details have been exactly thought out and come together to form an aesthetic whole that impresses in every way. This makes the IMPRESSA J7 a true design feature in the home, which, thanks to its compact design, can easily be placed anywhere. Pure ergonomics: The centrally arranged control elements, with the unique Rotary Switch and a plain text display which speaks your language, will allow you to quickly and intuitively make your coffee wishes come true. The focus is fully on your personal taste. Simply select the coffee strength, amount of water and temperature according to your individual preferences. You can even choose between three hot water temperature levels. Accessories such as the measuring spoon and the hot water nozzle can be conveniently stored in the storage compartment where they are always within reach. Energy-saving made easy: The IMPRESSA J7 actively assists you in saving energy. U With the Energy Save Mode (E.S.M.) you can adjust the energy saving potential to suit the way you like to enjoy your beverages.

Perfect enjoyment, perfect aesthetics
U Zero-Energy Switch: When the IMPRESSA is switched off with the on/off button, the machine is completely disconnected from the power supply. Z Height- and width-adjustable coffee spout: The height- and width-adjustable coffee spout is another JURA innovation. It allows precise adaptation to cups of different heights and diameters. This prevents the coffee from splashing and produces a delicious crema with the ideal consistency.

Connector System

The Connector System permits the use of different cappuccino frothers: Z Professional Cappuccino Frother U Cappuccino, latte macchiato U Hot milk and milk foam Z Easy Cappuccino Frother U Cappuccino U Milk foam Visit us on the internet. @ At www.jura.com you will find interesting and up-to-date information on your IMPRESSA and on every aspect of coffee.

JURA on the internet

Knowledge Builder
You can familiarise yourself with your IMPRESSA in a fun way on the PC. @ The Knowledge Builder awaits you at www.jura.com. The interactive assistant, LEO, will assist you and explain the benefits of and how to use your IMPRESSA.
2 Preparing and using for the first time
This chapter provides you with the information you need to use your IMPRESSA without any problems. You will prepare your IMPRESSA step-by-step to enjoy your first perfect cup of coffee.

Supplied as standard

The following items are supplied as standard: Z Your JURA IMPRESSA J7 automatic coffee machine Z The Welcome Pack, which includes: U The IMPRESSA J7 Manual U JURA cleaning tablets U Measuring spoon U Hot water nozzle U Aquadurtest strip U CLARIS Blue extension U CLARIS Blue filter cartridge U JURA Cappuccino Cleaner Keep the packaging for your IMPRESSA. It should be used to protect the machine during transport. When setting up your IMPRESSA, please note the following: Z Set the IMPRESSA down on a horizontal surface that is not sensitive to water. Z Choose a spot for your IMPRESSA which is protected against overheating.

Setting up

Filling the water tank
To enjoy the perfect cup of coffee we recommend changing the water every day. Milk, mineral water or other liquids can damage the water tank or the machine. T Only fill the water tank with fresh, cold water. T Open the water tank cover. T Remove the water tank and rinse it with cold water. T Fill the water tank with fresh, cold water and reinsert the tank. T Close the water tank cover.
Filling the bean container
The bean container has an aroma preservation cover. This will ensure that your coffee beans retain their aroma for longer. Coffee beans which have been treated with additives (e.g. sugar), pre-ground coffee or freeze-dried coffee will damage the grinder. T Only use untreated coffee beans to refill the bean container. T Open the bean container cover and remove the aroma preservation cover. T Remove any dirt or foreign objects inside the bean container. T Fill the bean container with coffee beans, then close the aroma preservation cover and the bean container cover.

First-time use

If the machine is operated with a defective mains cable, there is a danger of potentially fatal electric shock. T Never use a machine which has a defective mains cable. Precondition: The water tank and bean container are full. T Insert the mains plug into a power socket. 3 T Switch on the IMPRESSA using the power switch on the right-hand side of the machine. Q T Press the on/off button to switch the IMPRESSA on. The Rotary Switch lights up. SPRACHE DEUTSCH appears on the display. f T Turn the Rotary Switch until the required language is displayed, for example LANGUAGE ENGLISH. k T Press the Rotary Switch to confirm the language. OK appears briefly on the display to confirm the setting. PRESS RINSE, the maintenance button c lights up. T Place a receptacle under the frother. c T Press the maintenance button. SYSTEM FILLING, the system fills up with water. A small amount of water flows from the frother. This operation stops automatically, the following appears on the display: HEATING. PRESS RINSE, the maintenance button c lights up.

WARNING

T Place a receptacle under the coffee spout. c T Press the maintenance button. RINSING, the machine rinses. The operation stops automatically. READY appears on the display. Your IMPRESSA is ready for use.
Inserting and activating the filter
Your IMPRESSA no longer has to be descaled if you are using CLARIS Blue filter cartridges. @ You can also try out the Inserting the filter operation online. Visit the Knowledge Builder at www.jura.com. E Perform the Inserting the filter operation without interruptions. This will ensure that your IMPRESSA always produces its best. Precondition: READY is displayed. k T Keep the Rotary Switch pressed until RINSE appears on the display. g T Turn the Rotary Switch until FILTER - is displayed. k T Press the Rotary Switch to enter the programme item.
NO g T Turn the Rotary Switch until YES w is displayed. k T Press the Rotary Switch to confirm the setting. OK appears briefly on the display to confirm the setting. INSERT, the maintenance button c lights up. T Remove the filter cartridge extension from the Welcome Pack. T Fit the extension on top of an original CLARIS Blue filter cartridge. T Remove and empty the water tank. T Lift the cartridge holder and insert the filter cartridge into the water tank, exerting slight pressure. T Close the cartridge holder. It will click into place audibly. E After two months, the filter will cease to work. You can check the elapsed time by referring to the date plate on the cartridge holder in the water tank.

. T Touch the Start symbol. Preparation will now begin. 1 COFFEE appears on the display. g T Turn the Rotary Switch during preparation until 110 ML is displayed. The set amount of water flows into the cup. Preparation stops automatically and READY appears on the display.
Permanently setting the amount of water for the cup size
It is easy to make permanent settings for the amount of water for all speciality coffees as well as hot water and steam according to the cup size. As in the following example, adjust the amount of water once. Every time you prepare a drink in the future, this amount of water will be dispensed. The permanent settings for adapting the amount of water to the cup size for all speciality coffees, hot water and steam follow this model. Example: Proceed as follows to make permanent settings for the amount of water for a coffee. Precondition: READY is displayed. T Place a cup under the coffee spout. o T Touch the Coffee symbol. 1 COFFEE is displayed for about two seconds. The Coffee symbol is active.
. T Touch the Start symbol for about three seconds, until ENOUGH COFFEE ? appears on the display. Preparation starts and the coffee flows into the cup. T Touch the Start symbol as soon as there is sufficient coffee in the cup. Preparation stops. OK appears briefly on the display. The set amount of water for one coffee will be permanently stored. READY appears on the display. E You can alter these settings at any time by repeating the above procedure. E You can also make permanent settings for the amount of water for all speciality coffees in programming mode, in the BUTTONS programme item.
Permanent settings in programming mode
You can make permanent settings in programming mode. For example, you can change product settings such as aroma and the amount of water or activate an energy-saving mode. Simply by turning and pressing the Rotary Switch you can navigate through the easy-to-understand programme items and make permanent settings.
You can make the following settings with the Rotary Switch: Programme item Sub-item Explanation T Select the desired maintenance programme. If no action is taken, programming mode is exited automatically after approximately five seconds.
RINSE, CLEAN, FILTER (only if filter

is activated),

DE-SCALE (only if filter

is not activated)

BUTTONS FILTER -
SELECT BUTTON YES w NO INACTIVE, 1 dH 30 dH SAVE -, SAVE w 15 MIN, 0.5 HRS 15 HRS MANUAL, AUTOMATIC PRODUCT, ALL PROD., RESET ALL

PRODUCT

i T Touch the Espresso symbol. OK appears briefly on the display, the settings for Espresso are restored to the factory settings.
Viewing information and maintenance status
In the programme item INFO you can query the following information: Z Number of prepared speciality coffees, hot water and steam Z Maintenance status and number of maintenance programmes performed (cleaning, descaling, changing the filter) Z Software version k T Keep the Rotary Switch pressed until RINSE appears. g T Turn the Rotary Switch until INFO is displayed. k T Press the Rotary Switch to enter the programme item.
k T Press the Rotary Switch to enter the programme item. The total number of the prepared speciality coffees is displayed. E By touching the individual symbols for the speciality coffees, hot water and steam, the respective number of prepared products is displayed. E To query the number of double products prepared, touch the corresponding symbol for the speciality coffee twice. E Open the cover of the filler funnel for pre-ground coffee to query this number. k T Press the Rotary Switch to exit the programme item.
g T Turn the Rotary Switch until CLEAN is displayed.
E Continue turning the Rotary Switch to switch to the performed descaling and filter change operations. k T Press the Rotary Switch to enter the programme item. The number of performed cleaning operations appears on the display. E By turning the Rotary Switch, the maintenance status can also be displayed in addition to the number of performed maintenance programmes. The filled out fields show the maintenance status. Once all fields are filled out, your IMPRESSA will request the respective maintenance programme. k T Press the Rotary Switch to exit the programme item.

Unit for amount of water

You can change the unit for the amount of water from ml to oz. Example: Proceed as follows to change the unit for the amount of water from ML to OZ. k T Keep the Rotary Switch pressed until RINSE appears. g T Turn the Rotary Switch until DISPLAY is displayed. k T Press the Rotary Switch to enter the programme item.
g T Turn the Rotary Switch until OZ is displayed. k T Press the Rotary Switch to confirm the setting. OK appears briefly on the display.

DISPLAY

Language
The language of your IMPRESSA is set with this programme item. Example: Proceed as follows to change the language from ENGLISH to DEUTSCH. Precondition: READY is displayed. k T Keep the Rotary Switch pressed until RINSE appears. g T Turn the Rotary Switch until LANGUAGE is displayed. k T Press the Rotary Switch to enter the programme item.

ENGLISH

g T Turn the Rotary Switch until DEUTSCH is displayed. k T Press the Rotary Switch to confirm the setting. OK appears briefly on the display.

SPRACHE

BEREIT

6 Maintenance

Your IMPRESSA has the following integrated maintenance programmes: Z Rinsing the machine Z Changing the filter Z Cleaning the machine Z Descaling the machine E Clean or descale the machine or change the filter when you are prompted to do so.

Maintenance tips

To ensure that you get many years of reliable service out of your IMPRESSA and to guarantee the optimum coffee quality, the machine requires daily maintenance. Proceed as follows: Z Empty the coffee grounds container and the drip tray. Rinse them with warm water. Z Rinse the water tank with clean water. Z Dismantle and rinse the frother (see Chapter 6, Maintenance Dismantling and rinsing the cappuccino frother). Z Wipe the surface of the machine with a clean, soft, damp cloth (e.g. microfibre cloth).

Rinsing the machine

When the IMPRESSA is switched on, a prompt to perform rinsing appears after heating, or this is automatically started. It can be set in programming mode whether the switch-on rinse needs to be activated manually or whether the machine automatically activates the switch-on rinse (see Chapter 5, Permanent settings in programming mode - Rinses). When the IMPRESSA is switched off, a rinse operation is automatically initiated. You can initiate the rinse operation manually at any time.
Precondition: READY is displayed. T Place a receptacle under the coffee spout. k T Keep the Rotary Switch pressed until RINSE appears. k T Press the Rotary Switch to enter the programme item.
k T Press the Rotary Switch to initiate the rinse operation. RINSING, water flows out of the coffee spout. Rinsing stops automatically and your IMPRESSA is then ready for use.

Changing the filter

E After 50 litres of water have flowed through, the filter will cease to work. Your IMPRESSA will automatically prompt you to change the filter. E After two months, the filter will cease to work. You can check the elapsed time by referring to the date plate on the cartridge holder in the water tank. E If the CLARIS Blue filter cartridge is not activated, you will not be prompted to change the filter. @ You can also try out the changing the filter operation online. Visit the Knowledge Builder at www.jura.com.

T Insert a JURA cleaning tablet into the filler funnel. T Close the cover of the filler funnel. PRESS RINSE, the maintenance button c lights up. c T Press the maintenance button. CLEANING, water flows out of the coffee spout several times. The operation is interrupted, EMPTY TRAY. T Empty the drip tray and coffee grounds container and put them back into the machine.
The cleaning operation is now complete. The IMPRESSA is once more ready for use. Manual cleaning You can initiate the Cleaning the machine operation manually. Precondition: READY is displayed. k T Keep the Rotary Switch pressed until RINSE appears. k T Press the Rotary Switch to enter the programme item.
g T Turn the Rotary Switch until CLEAN is displayed. k T Press the Rotary Switch.
T Continue with the second prompt to take action (indicated by a T), as is described under Cleaning after a prompt.

Descaling the machine

The IMPRESSA builds up deposits of limescale over time and automatically prompts you to descale it when necessary. The degree of calcification depends on the degree of hardness of your water. If the descaling agent comes into contact with the skin or eyes, this can cause irritation. T Avoid contact with the skin or eyes. T If descaling agent does come into contact with the skin or eyes, rinse off with clean water. Should you get any descaling agent in your eye, see a doctor. If the wrong descaling agent is used, the machine could be damaged and/or traces of detergent could be left behind in the water. T Use only original JURA maintenance products. If the descaling operation is interrupted, there may be damage to the machine. T Allow the descaling programme to run to the end. If the descaling agent comes into contact with sensitive surfaces, damage cannot be ruled out. T Clean up any splashes immediately.
E The descaling programme lasts approx. 45 minutes. E JURA descaling tablets are available from stockists. E If you use a CLARIS Blue filter cartridge and this is activated, you will not be prompted to descale. @ You can also try out the Descaling the machine operation online. Visit the Knowledge Builder at www.jura.com. Descaling after a prompt Precondition: READY / DE-SCALE is displayed and the maintenance button c lights up. c T Press the maintenance button.
T Empty the drip tray and coffee grounds container and put them back into the machine.

AGENT IN TANK

T Remove and empty the water tank. T Completely dissolve the contents of one blister (three JURA descaling tablets) in a container that holds 500 ml of water. This may take several minutes. T Pour the solution into the empty water tank and insert it in the machine. AGENT IN TANK, the maintenance button c lights up. T Remove the cappuccino frother from the Connector System. T Place a receptacle (at least 500 ml) under the Connector System. c T Press the maintenance button.

DE-SCALING

This causes water to flow out of the Connector System several times. The maintenance button blinks during the descaling operation. The operation stops automatically, EMPTY TRAY. T Empty the receptacle under the Connector System. T Empty the drip tray and coffee grounds container and put them back into the machine.

FILL WATER TANK

T Remove the water tank and rinse it thoroughly.
T Fill the water tank with fresh, cold water and reinsert the tank. PRESS RINSE, the maintenance button c lights up. T Replace the cappuccino frother. T Place a receptacle under the frother and another under the coffee spout. c T Press the maintenance button. DE-SCALING, water flows out of the frother and the coffee spout. The operation stops automatically, EMPTY TRAY. T Empty the drip tray and coffee grounds container and put them back into the machine. The descaling operation is now complete. Your IMPRESSA heats up and is once more ready for use. E If the descaling operation stops unexpectedly, rinse the water tank thoroughly. Manual descaling You can initiate the Descaling the machine operation manually. Precondition: READY is displayed and the filter is not activated. k T Keep the Rotary Switch pressed until RINSE appears. k T Press the Rotary Switch to enter the programme item.
g T Turn the Rotary Switch until DE-SCALE is displayed. k T Press the Rotary Switch.
T Continue with the second prompt to take action (indicated by a T), as is described under Descaling after a prompt.
Rinsing the cappuccino frother
E This chapter applies to the Professional and Easy Cappuccino Frothers. To ensure that the cappuccino frother works perfectly, you should rinse it with water after every milk preparation. Your IMPRESSA will not prompt you to rinse the cappuccino frother.
Precondition: READY is displayed. T Remove the milk pipe from the milk carton/bottle or the milk container. T Fill a receptacle with fresh water and immerse the milk pipe in it. T Place a receptacle under the cappuccino frother. E If you are using the Professional Cappuccino Frother, turn the selector switch to the milk foam p or milk t position. n T Touch the Steam symbol.
As soon as the machine has heated up, READY appears. n T Touch the Steam symbol again. STEAM, the frother and milk pipe are rinsed. T Touch the Start symbol as soon as clean water flows out of the frother. The operation stops and your IMPRESSA is once more ready for use.
Cleaning the cappuccino frother
E This chapter applies to the Professional and Easy Cappuccino Frothers. To ensure that the cappuccino frother works perfectly, you should clean it daily when you have been preparing milk. Your IMPRESSA will not prompt you to clean the cappuccino frother.

If the wrong cleaning agent is used, the machine could be damaged and/or traces of detergent could be left behind in the water. T Use only original JURA maintenance products. E JURA Cappuccino Cleaner is available from stockists. @ You can also try out the Cleaning the cappuccino frother operation online. Visit the Knowledge Builder at www.jura.com.
Precondition: READY is displayed. T Remove the milk pipe from the milk carton/bottle or the milk container. T Pour 250 ml of fresh water into a receptacle and add one capful (max. 15 ml) of Cappuccino Cleaner. T Immerse the milk pipe in the receptacle. T Place another receptacle under the frother. E If you are using the Professional Cappuccino Frother, turn the selector switch to the milk foam p or milk t position. n T Touch the Steam symbol.
As soon as the machine has heated up, READY appears. n T Touch the Steam symbol again. STEAM, the frother and milk pipe are cleaned. T Touch the Start symbol as soon as the receptacle containing the Cappuccino Cleaner is empty. T Rinse the receptacle thoroughly, fill it with approx. 250 ml of fresh water and immerse the milk pipe in the water. T Empty the other receptacle and place it under the frother once more. n T Touch the Steam symbol. STEAM, the frother and milk pipe are rinsed with fresh water. T Touch the Start symbol as soon as the receptacle containing the water is empty. The operation stops and your IMPRESSA is once more ready for use.
Dismantling and rinsing the Professional Cappuccino Frother
T Carefully remove the frother from the Connector System by twisting slightly. T Dismantle the frother completely. T Rinse all frother parts thoroughly under running water. T Re-assemble the frother. E Ensure that all individual parts are correctly and firmly connected to ensure correct operation of the frother T Firmly attach the frother to the Connector System.
Dismantling and rinsing the Easy Cappuccino Frother
T Carefully remove the frother from the Connector System by twisting slightly. T Dismantle the frother completely. T Rinse all frother parts thoroughly under running water. T Re-assemble the frother. E Ensure that all individual parts are correctly and firmly connected to ensure correct operation of the frother. T Firmly attach the frother to the Connector System.

ERROR 2

is displayed.
If the machine was exposed to the cold for a long period of time, heating is disabled for safety reasons.
Other ERROR messages are displayed.
T Turn the IMPRESSA off at the power switch. Contact Customer Support in your country (see Chapter JURA contact details / Legal information).
E If you were unable to solve the problem, contact Customer Support in your country (see Chapter JURA contact details / Legal information).
9 Transport and environmentally neutral disposal
Transport / Emptying the system
Keep the packaging for your IMPRESSA. It should be used to protect the machine during transport. In order to protect the IMPRESSA from frost during transport, the system must be emptied. Precondition: READY is displayed. T Carefully pull the cappuccino frother off the Connector System. T Place a receptacle under the Connector System. n T Touch the Steam symbol.
As soon as the machine has heated up, READY appears. n T Touch the Steam symbol again. STEAM, hot steam is discharged from the Connector System. T Remove and empty the water tank. Steam will continue to be discharged from the Connector System until the system is empty.

PRESS RINSE

Q T Press the on/off button. The IMPRESSA is switched off. E The next time you use the machine the system must be refilled (see Chapter 2, Preparing and using for the first time First-time use).

Disposal

Please dispose of old machines in an environmentally neutral way.
Old machines contain valuable materials capable of being recycled which should be salvaged for recycling. Please therefore dispose of old machines via suitable collection systems.

10 Technical data

Voltage AS F D G Power Safety test Power consumption 1450 W SDFG 12 Wh 7 Wh Static max. 15 bar 2,1 l 250 g Approx. 16 servings Approx. 1,1 m 10,75 kg 28,5 x 34,2 x 43,3 cm V ~, 50 Hz 120 V ~, 60 Hz V ~, 50 Hz 220 V ~, 50 Hz
ENERGY SAVE Power consumption

ENERGY SAVE w

Pump pressure Holding capacity of water tank Holding capacity of bean container Holding capacity of coffee grounds container Cable length Weight Dimensions (W x H x D)

Index A

Amount

Descaling Display

Machine 46 Water tank 52 Messages 53

Amount of coffee

Changing the amount of water during preparation 25 Entering a permanent setting for the amount of water for the cup size 26 Changing the amount of water during preparation 25 Entering a permanent setting for the amount of water for the cup size 26 Changing during preparation 25 Setting the water for the cup size 26

Technical data 58 Transport 57 Troubleshooting 55 Viewing information and maintenance status 39 Viewing maintenance status 39 Water tank 8

Descaling 52 Filling 16

Art. 68817/J7/en/201011
JURA contact details / Legal information
JURA Elektroapparate AG Kaffeeweltstrasse 10 CH-4626 Niederbuchsiten Tel.: +233
@ Further contact information is available on the company

website at www.jura.com.

Directives
The machine complies with the following EU directives: Z 2006/95/EG Low Voltage Directive Z 2004/108/EG Electromagnetic Compatibility Z 2009/125/EG Energy Directive We reserve the right to make technical changes. The illustrations used in the IMPRESSA J7 Manual show the IMPRESSA J7 Piano Black. Your IMPRESSA could incorporate minor changes.

Technical changes

Feedback Copyright
Your opinion is important to us! Use the contact link at www.jura.com. The Instructions for Use contain information which is protected by copyright. It is not permitted to photocopy or translate these Instructions for Use into another language without the express written consent of JURA Elektroapparate AG.

IMPRESSA J7 Quick Reference Guide
The IMPRESSA J7 Instructions for Use together with these short instructions IMPRESSA J7 Quick Reference Guide has been awarded the seal of approval by the independent German Technical Inspection Agency, TV SD, due to its easy-to-understand style, its thoroughness and coverage of safety aspects.
These short instructions do not replace the IMPRESSA J7 Instructions for Use. Make sure you read and observe the safety information and warnings first in order to avoid hazards.

Rinsing the machine

You can initiate the rinse operation manually at any time. Precondition: READY is displayed. T Place a receptacle under the coffee spout. k T Keep the Rotary Switch pressed until RINSE appears. k T Press the Rotary Switch to enter the programme item.
k T Press the Rotary Switch to initiate the rinse operation. RINSING, water flows out of the coffee spout. Rinsing stops automatically and your IMPRESSA is then ready for use.
Inserting and activating the filter
Your IMPRESSA no longer has to be descaled if you are using CLARIS Blue filter cartridges.
E Perform the Inserting the filter operation without interruptions. This will ensure that your IMPRESSA always produces its best. Precondition: READY is displayed. k T Keep the Rotary Switch pressed until RINSE appears on the display. g T Turn the Rotary Switch until FILTER - is displayed. k T Press the Rotary Switch to enter the programme item.
NO g T Turn the Rotary Switch until YES w is displayed. k T Press the Rotary Switch to confirm the setting. OK appears briefly on the display to confirm the setting. INSERT, the maintenance button c lights up. T Remove the filter cartridge extension from the Welcome Pack. T Fit the extension on top of an original CLARIS Blue filter cartridge. T Remove and empty the water tank.
T Lift the cartridge holder and insert the filter cartridge into the water tank, exerting slight pressure. T Close the cartridge holder. It will click into place audibly.
E After two months, the filter will cease to work. You can check
the elapsed time by referring to the date plate on the cartridge holder in the water tank. T Fill the water tank with fresh, cold water and reinsert the tank. T Place a receptacle (at least 500 ml) under the frother.
E If you are using the Professional Cappuccino Frother, set the
selector switch of the frother to the steam position n. c T Press the maintenance button. FILTER RINSING. Water flows out of the frother.
E You can interrupt rinsing of the filter at any time by pressing
the maintenance button c. E The water may be slightly discoloured. This is not harmful to health and does not affect the taste. Rinsing of the filter stops automatically after approximately 500 ml. HEATING appears on the display, then READY is displayed. The filter is now activated.

Changing the filter

E After 50 litres of water have flowed through, the filter will
cease to work. Your IMPRESSA will automatically prompt you to change the filter. E After two months, the filter will cease to work. You can check the elapsed time by referring to the date plate on the cartridge holder in the water tank. E If the CLARIS Blue filter cartridge is not activated, you will not be prompted to change the filter.
Proceed as follows to change the CLARIS Blue filter cartridge when prompted to do so by your IMPRESSA. Precondition: READY / FILTER is displayed and the maintenance button c lights up. c T Press the maintenance button.

CHANGE

T Remove and empty the water tank. T Lift the cartridge holder. T Take out the old filter cartridge and the extension. T Fit the extension on top of a new filter cartridge. T Insert the filter cartridge into the water tank, exerting slight pressure. T Close the cartridge holder. It will click into place audibly. T Fill the water tank with fresh, cold water and reinsert the tank.
T Place a receptacle (at least 500 ml) under the frother.
selector switch of the frother to the steam position n. c T Press the maintenance button. FILTER RINSING, water will flow out of the frother.
E You can interrupt rinsing of the filter at any time. To this purpose press the maintenance button c.
E The water may be slightly discoloured. This is not harmful to
health and does not affect the taste. Rinsing of the filter stops automatically after approximately 500 ml. The IMPRESSA heats up and is once more ready for use.
Rinsing the cappuccino frother
E This chapter applies to the Professional and Easy Cappuccino
Frothers. To ensure that the cappuccino frother works perfectly, you should rinse it with water after every milk preparation. Your IMPRESSA will not prompt you to rinse the cappuccino frother. Precondition: READY is displayed. T Remove the milk pipe from the milk carton/bottle or the milk container. T Fill a receptacle with fresh water and immerse the milk pipe in it. T Place a receptacle under the cappuccino frother.

E If you are using the Professional Cappuccino Frother, turn
the selector switch to the milk foam p or milk t position. n T Touch the Steam symbol.

HEATING

As soon as the machine has heated up, READY appears. n T Touch the Steam symbol again. STEAM, the frother and milk pipe are rinsed. T Touch the Start symbol as soon as clean water flows out of the frother. The operation stops and your IMPRESSA is once more ready for use.
Cleaning the cappuccino frother
Frothers. To ensure that the cappuccino frother works perfectly, you should clean it daily when you have been preparing milk. Your IMPRESSA will not prompt you to clean the cappuccino frother.

CAUTION

If the wrong cleaning agent is used, the machine could be damaged and/or traces of detergent could be left behind in the water. T Use only original JURA maintenance products.
E JURA Cappuccino Cleaner is available from stockists.
Precondition: READY is displayed. T Remove the milk pipe from the milk carton/bottle or the milk container. T Pour 250 ml of fresh water into a receptacle and add one capful (max. 15 ml) of Cappuccino Cleaner. T Immerse the milk pipe in the receptacle. T Place another receptacle under the frother.
As soon as the machine has heated up, READY appears. n T Touch the Steam symbol again. STEAM, the frother and milk pipe are cleaned. T Touch the Start symbol as soon as the receptacle containing the Cappuccino Cleaner is empty. T Rinse the receptacle thoroughly, fill it with approx. 250 ml of fresh water and immerse the milk pipe in the water. T Empty the other receptacle and place it under the frother once more. n T Touch the Steam symbol. STEAM, the frother and milk pipe are rinsed with fresh water. T Touch the Start symbol as soon as the receptacle containing the water is empty. The operation stops and your IMPRESSA is once more ready for use.
Dismantling and rinsing the Professional Cappuccino Frother
T Carefully remove the frother from the Connector System by twisting slightly. T Dismantle the frother completely. T Rinse all frother parts thoroughly under running water. T Re-assemble the frother.
E Ensure that all individual parts are correctly and firmly connected to ensure correct operation of the frother T Firmly attach the frother to the Connector System.
Dismantling and rinsing the Easy Cappuccino Frother
E Ensure that all individual parts are correctly and firmly connected to ensure correct operation of the frother. T Firmly attach the frother to the Connector System.

Cleaning the machine

After 200 coffee preparations or 80 switch-on rinses, the IMPRESSA will prompt you to clean it. If the wrong cleaning agent is used, the machine could be damaged and/or traces of detergent could be left behind in the water. T Use only original JURA maintenance products.

E The cleaning programme only lasts about 20 minutes. E Do not interrupt the cleaning programme. The quality of
cleaning will be impaired if you do so.
E JURA cleaning tablets are available from stockists.
Precondition: READY / CLEAN is displayed and the maintenance button c lights up. c T Press the maintenance button.

EMPTY TRAY

T Empty the drip tray and coffee grounds container and put them back into the machine. PRESS RINSE, the maintenance button c lights up. T Place a receptacle under the coffee spout. c T Press the maintenance button. CLEANING, water flows out of the coffee spout. The operation is interrupted, ADD TABLET. T Open the cover of the filler funnel for pre-ground coffee.
T Insert a JURA cleaning tablet into the filler funnel. T Close the cover of the filler funnel. PRESS RINSE, the maintenance button c lights up. c T Press the maintenance button. CLEANING, water flows out of the coffee spout several times. The operation is interrupted, EMPTY TRAY. T Empty the drip tray and coffee grounds container and put them back into the machine. The cleaning operation is now complete. The IMPRESSA is once more ready for use.

Descaling the machine

The IMPRESSA builds up deposits of limescale over time and automatically prompts you to descale it when necessary. The degree of calcification depends on the degree of hardness of your water. If the descaling agent comes into contact with the skin or eyes, this can cause irritation. T Avoid contact with the skin or eyes. T If descaling agent does come into contact with the skin or eyes, rinse off with clean water. Should you get any descaling agent in your eye, see a doctor. If the wrong descaling agent is used, the machine could be damaged and/or traces of detergent could be left behind in the water. T Use only original JURA maintenance products. If the descaling operation is interrupted, there may be damage to the machine. T Allow the descaling programme to run to the end. If the descaling agent comes into contact with sensitive surfaces, damage cannot be ruled out. T Clean up any splashes immediately.
E The descaling programme lasts approx. 45 minutes. E JURA descaling tablets are available from stockists. E If you use a CLARIS Blue filter cartridge and this is activated,
you will not be prompted to descale. Precondition: READY / DE-SCALE is displayed and the maintenance button c lights up. c T Press the maintenance button.
T Empty the drip tray and coffee grounds container and put them back into the machine.

AGENT IN TANK

T Remove and empty the water tank.
T Completely dissolve the contents of one blister (three JURA descaling tablets) in a container that holds 500 ml of water. This may take several minutes. T Pour the solution into the empty water tank and insert it in the machine. AGENT IN TANK, the maintenance button c lights up. T Remove the cappuccino frother from the Connector System. T Place a receptacle (at least 500 ml) under the Connector System. c T Press the maintenance button.

DE-SCALING

This causes water to flow out of the Connector System several times. The maintenance button blinks during the descaling operation. The operation stops automatically, EMPTY TRAY. T Empty the receptacle under the Connector System. T Empty the drip tray and coffee grounds container and put them back into the machine.

FILL WATER TANK

T Remove the water tank and rinse it thoroughly. T Fill the water tank with fresh, cold water and reinsert the tank. PRESS RINSE, the maintenance button c lights up. T Replace the cappuccino frother. T Place a receptacle under the frother and another under the coffee spout. c T Press the maintenance button. DE-SCALING, water flows out of the frother and the coffee spout. The operation stops automatically, EMPTY TRAY. T Empty the drip tray and coffee grounds container and put them back into the machine. The descaling operation is now complete. Your IMPRESSA heats up and is once more ready for use.
E If the descaling operation stops unexpectedly, rinse the water

tank thoroughly.

J7/en/Kurz/20091007