IMPRESSA XF50

Type 661 Original instructions for use
Before using the machine read the instructions for use.

Legend:

DISPLAY: serves as information. DISPLAY: please follow the instructions shown. = Note / Tip = Important

Fig. 1

Fig. 2

Fig. 3

Fig. 4

Fig. 5

Fig. 6

Fig. 7

Fig. 8

Fig. 9

Fig. 10

Fig. 11

Fig. 12

Fig. 13

Fig. 18
Fig. 19 Fig. 14 Fig. 15 Fig. 16 Fig. 17

Temp. max.

Fig. 20

Temp. min.

Control elements
1. Rotary Switch 2. Illuminated ring 3. Maintenance button 4. Preparation button, 1 espresso 5. Preparation button, 2 espressi

14 15/16

6. Preparation button, 1 coffee 7. Preparation button, 2 coffees 8. Steam preselection button 9. Display dialogue system 10. Water tank with handle 11. Filler funnel for preground coffee 12. Bean container cover 13. Aroma preservation cover 14. Steam / hot water draw-off tap 15. Removable Professional Cappuccino Frother with milk pipe 16. Removable hot-water nozzle (see Fig. 5) 17. Height-adjustable coffee spout 18. Coffee grounds container 19. Cup grille

Rotary Switch

20. Drip tray 21. On/Off button (= Zero-Energy Switch) 22. Metal shelf

Table of contents

1. Safety instructions. page 1.1 Proper use. page 1.2 Warnings. page 1.3 Precautions. page 2. Preparing the IMPRESSA. page 2.1 Checking the mains voltage. page 2.2 Checking the electric fuse. page 2.3 Filling the water tank. page 2.4 Filling with coffee beans. page 2.5 Adjusting the grinder. page 3. Using for the first time. page 4. Adjusting the water hardness. page 5. Using the CLARIS filter cartridge. page 5.1 Inserting the filter. page 5.2 Changing the filter. page 6. Rinsing the IMPRESSA. page 7. Adjusting the amount of water for coffee. page 8. Preparing 1 cup of coffee. page 9. Preparing 2 cups of coffee. page 10. Preparing preground coffee. page 11. Preparing hot water. page 12. Preparing steam. page 13. Professional Cappuccino Frother. page 13.1 Preparing cappuccino with the Professional Cappuccino Frother. page 13.2 Preparing hot milk with the Professional Cappuccino Frother. page 13.3 Rinsing the Professional Cappuccino Frother. page 13.4 Dismantling and rinsing the Professional Cappuccino Frother. page 13.5 Cleaning the Professional Cappuccino Frother. page
14. Switching off the IMPRESSA. page 15. Programming. page 15.1 Buttons programme item. page 15.2 Filter programme item. page 15.3 Water hardness programme item. page 15.4 Energy programme item. page 15.5 Automatic switch-off time programme item. page 15.6 Rinse programme item. page 15.7 Reset programme item. page 15.8 Counter programme item. page 15.9 Lock programme item. page 15.10 Information programme item. page 15.11 ML/OZ display programme item. page 15.12 Language programme item. page 16. Maintenance. page 16.1 Filling with water. page 16.2 Emptying coffee grounds container. page 16.3 Drip tray missing. page 16.4 Filling with coffee beans. page 16.5 Changing the filter. page 16.6 Cleaning the IMPRESSA. page 16.7 IMPRESSA calcification. page 16.8 General cleaning instructions. page 16.9 Emptying the system. page 17. Cleaning. page 18. Descaling. page 19. Disposal. page 20. Tips for a perfect coffee. page 21. Messages. page 22. Problems. page 23. Legal information. page 24. Technical data. page

Before you get started

Congratulations on purchasing this IMPRESSA. To ensure that your IMPRESSA works smoothly, please read these instructions for use carefully and keep them as a future reference. If you need more information or if you experience any problems which are not covered in enough detail in these instructions for use, please contact your local stockist or ourselves.
In the event of signs of damage, for example if there is a smell of burning, unplug the machine immediately from the mains supply and contact JURA service. If the mains cable of this machine is damaged, it must be repaired either directly by JURA or by an authorised JURA service centre. Never repair or open the IMPRESSA yourself. Repairs and modifications to the machine may only be undertaken by authorised JURA service centres using genuine spare parts and accessories. The machine contains live parts. If opened, there is a danger of potentially fatal injury. Do not immerse the IMPRESSA in water.

1. Safety instructions 1.1 Proper use
The machine is designed and intended for commercial use. It should only be used for coffee preparation and to heat milk and water. Use for any other purpose will be deemed improper. JURA Elektroapparate AG cannot accept any responsibility for the consequences of improper use. Before using the machine read these instructions for use thoroughly and completely and comply with the instructions they contain. Keep these instructions for use close to the machine and pass them on to the next user.

1.3 Precautions

Never subject the IMPRESSA to environmental influences (rain, snow, frost) and do not operate with wet hands. Do not set up the IMPRESSA XF50 anywhere where a jet of water may be used. Place the IMPRESSA on a sturdy, horizontal surface resistant to any water leaks. Never place on hot or warm surfaces (hobs). Select a site out of reach of children. Be careful to ensure that the mains cable is not trapped and does not rub against sharp edges. Always remove the mains plug during long periods of absence (holidays etc.). Always remove the mains plug before cleaning. When removing the mains plug, never tug the supply cable or the IMPRESSA itself.

1.2 Warnings

The IMPRESSA may only be operated by instructed persons. Never start up a defective IMPRESSA or an IMPRESSA with a damaged supply cable.
The IMPRESSA is connected to the power supply by a supply cable. Make sure people cant trip over the supply cable, bringing down the IMPRESSA. Make sure children and pets cannot reach the machine. Never put the IMPRESSA or individual parts of it in the dishwasher. Install the IMPRESSA in a place where the air can circulate well to prevent it from overheating.
2.4 Filling with coffee beans
To make sure you get lasting enjoyment from your machine and to avoid the need for repairs, please note that the grinder in your JURA coffee machine is not suitable for coffee beans that have been treated with additives (e.g. sugar) during or after roasting. Using coffee blends of this type may damage the grinder. Any resulting repair costs will not be covered by the warranty conditions. Fold the bean container cover (12) open and remove the aroma preservation cover (13). Remove any dirt or foreign objects from inside the bean container. Fill the bean container with coffee beans and close the cover.

2. Preparing the IMPRESSA 2.1 Checking the mains voltage
The IMPRESSA is set to the right mains voltage by default. Check whether your mains voltage matches that stated on the rating plate on the underside of your IMPRESSA.
2.5 Adjusting the grinder 2.2 Checking the electric fuse
The IMPRESSA is rated for a current of 10 amps. Check whether a fuse for this rating is fitted. You can adjust the grinder to the suit the degree of roast of your coffee. Our recommendations: a light roast a finer setting (the smaller the dots, the finer the grinding) a dark roast a coarser setting (the larger the dots, the coarser the grinding) Only use the switch to adjust the consistency of grind when the grinder is running. Open the bean container cover (12) and remove the aroma preservation cover (13). To adjust the consistency of grind, turn the switch to the desired position during the grinding operation (Fig. 2).
2.3 Filling the water tank
Only top up with fresh, cold water. Never fill with milk, mineral water or other liquids. Remove the water tank and rinse it well with cold mains water (Fig. 4). Then fill the water tank and refit in the IMPRESSA. Be careful to ensure that the tank is correctly inserted and properly engaged.
3. Using for the first time
Fill the bean container with coffee beans (12). Switch your IMPRESSA on with the On/Off button SPRACHE DEUTSCH (21).
The machine rinses. RINSING READY If FILL BEANS appears on the display, again press any coffee preparation button. The grinder is not yet filled with coffee beans. To get a really good crema you can individually adjust the height-adjustable coffee spout (17) to your cup sizes (Fig. 3).
The illuminated ring (2) is active. Turn the Rotary Switch (1) until the desired language appears on the display. Now confirm your selection by pressing the Rotary Switch (1). FILL WATER TANK
4. Adjusting the water hardness
Water is heated in the IMPRESSA. Over time this will result in calcification and this is displayed automatically. The IMPRESSA must be set to the hardness of the water used. Use the test strips provided. 1 German hardness corresponds to 1.79 French hardness. When the filter is activated, the water hardness programme item disappears. The IMPRESSA is set to 16 dH by default. You can change this setting. Proceed as follows: READY Press and hold the Rotary Switch (1) until RINSE appears on the display. The illuminated ring (2) is active. Turn the Rotary Switch (1) until the following message appears on the display: (3).

If you do not change the steam preparation time on the Rotary Switch (1), you prepare the saved amount of steam. Once the amount of steam is reached, the following message appears on the display: CLOSE TAP READY The machine is ready to prepare steam for around 40 sec., then the machine is reset so that it is ready to brew coffee. You can prematurely stop steam preparation at any time by closing the steam / hot water draw-off tap (13). Due to the system design, some steam may be released before the tap is closed. There is a danger of scalding. Close the steam / hot water draw-off tap (14).
13. Professional Cappuccino Frother 13.1 Preparing cappuccino with the Professional Cappuccino Frother
Cappuccino is made up of one third espresso, one third warm milk and one third milk foam. The Professional Cappuccino Frother (15) is used for preparing the milk portion. When steam is drawn off, a negative pressure is created and this draws milk with the aid of the Professional Cappuccino Frother (15) and produces milk foam. You can also heat up milk by turning the selector switch on the Professional Cappuccino Frother to the Milk position (Fig. 20).
Open the steam / hot water draw-off tap (Fig. 13) to draw off steam. The milk foam is prepared. The illuminated ring (2) is active. STEAM
Now, move your cup with the milk foam under the coffee spout and draw off the desired speciality coffee (Fig. 8). Your cappuccino is ready.
You can adjust the steam preparation time individually by turning the Rotary Switch (1) until the desired number of SEC appear on the display. For example 25 SEC.
13.2 Preparing hot milk with the Professional Cappuccino Frother
Turn the selector switch on the Professional Cappuccino Frother to the Milk position (Fig. 20). The operation for preparing hot milk is the same as that for preparing milk foam for a cappuccino (see chapter 13 Preparing cappuccino with the Professional Cappuccino Frother).
If you do not change the steam preparation time on the Rotary Switch (1), you prepare the saved amount of steam. Adjust the steam preparation time to suit the size of your cup. Once the amount of steam is reached, the following message appears on the display: CLOSE TAP Close the steam / hot water draw-off tap (14). READY The machine is ready to prepare steam for around 40 sec., then the machine is reset so that it is ready to brew coffee. You can prematurely stop steam preparation at any time by closing the steam / hot water draw-off tap (14). Due to the system design, some steam and milk may be released before the tap is closed. There is a danger of scalding.

13.5 Cleaning the Professional Cappuccino Frother
To ensure that the Professional Cappuccino Frother (15) always works properly, you should clean it daily when you have been preparing milk foam or hot milk. Your IMPRESSA will not prompt you to clean the Professional Cappuccino Frother. JURA Cappuccino Cleaner is available from stockists.
Ignoring the CLOSE TAP display message, draw off steam until the receptacle containing fresh water is empty. Then close the steam / hot water draw-off tap (14). The Professional Cappuccino Frother (15) and the milk pipe are rinsed with fresh water. Cleaning of the Professional Cappuccino Frother is complete, your IMPRESSA is ready for use.
You can program the following settings: RINSE BUTTONS FILTER HARDNESS ENERGY OFF AFTER RINSING RESET COUNTER LOCK INFO DISPLAY LANGUAGE Rotary Switch Permanent settings in programming mode always follow the same model. To enter programming mode, press the Rotary Switch (1) until RINSE appears on the display. By turning the Rotary Switch (1) you can change the set values and select different programme items. By pressing the Rotary Switch (1) you can view values or save selected values.
14. Switching off the IMPRESSA
READY (21). RINSING Switch the IMPRESSA off with the On/Off button Automatic switch-off rinse is started. Just one automatic rinse is started if at least 1 speciality coffee has been prepared. Otherwise the machine switches off without a rinse.

15. Programming

The IMPRESSA is configured in the factory such that you can prepare coffee without any additional programming. You can individually program various settings to adapt your beverages to your personal taste.
You can select and adapt the following programme items to your needs:
Programme item Sub-item RINSE RINSE FILTER (only appears if filter is activated) CLEAN DE-SCALE (only appears if filter is not activated) EXIT SELECT BUTTON EXIT NO YES INACTIVE dH Explanation Select the desired maintenance programme. If no action is taken, programming mode is exited automatically after approximately five seconds. For more information, please refer to chapters 6 and 16 to 18.
Programme item Sub-item RESET PRODUCT ALL PROD. RESET ALL EXIT DELETE YES DELETE NO BUTTONS PRE-SELECT MAINTAIN EXIT BUTTONS CLEAN FILTER (only appears if filter is activated) DE-SCALE (only appears if filter is not activated) VERSION EXIT ML OZ DEUTSCH ENGLISH FRANCAIS ITALIANO NL ESPANOL PORTUGUES

Explanation Reset the settings for individual products, all products or the entire machine to the factory setting. Refer to the counter for information about the products consumed and reset to zero if necessary. Lock individual speciality coffees, the aroma preselection and the amount of water adjustment during coffee preparation or the maintenance functions. Keep track of all prepared speciality coffees and milk specialities and view the maintenance status.

COUNTER

BUTTONS
Select your settings for speciality coffees, milk specialities and hot water. Indicate whether you want to operate your IMPRESSA with or without a CLARIS filter cartridge. Adjust the water hardness.

FILTER /

HARDNESS (only appears if filter is not activated)
ENERGY / SAVE SAVE OFF AFTER 15 MIN to 15 HRS
Select an energy-saving mode. Set the number of hours after which the IMPRESSA should switch off automatically. Set whether the switch-on rinse should be started manually or automatically.

DISPLAY LANGUAGE

Select the unit for the amount of water. Select your language.

RINSING

MANUAL AUTOMATIC
15.1 Buttons programme item
With the BUTTONS programme item you can enter individual settings for all speciality coffees, milk and hot water. Permanent settings in programming mode always follow the same model. The following permanent settings can be made for speciality coffees, milk and hot water:
Product 2 espressi 1 coffee 2 coffees Milk Amount of water Strength Temperature 1 espresso 25 ML 240 ML MILD, NORMAL, STRONG, XSTRONG NORMAL, HIGH 25 ML 240 ML MILD, NORMAL, STRONG, XSTRONG NORMAL, HIGH 25 ML 240 ML MILD, NORMAL, STRONG, XSTRONG NORMAL, HIGH 25 ML 240 ML MILD, NORMAL, STRONG, XSTRONG NORMAL, HIGH SEC NORMAL, HIGH
Press the preparation button for the speciality coffee for which you want to adjust the amount of water. For example, 1 COFFEE. WATER 100 ML. 110 ML. Press the Rotary Switch (1). For example For example OK WATER Turn the Rotary Switch (1) to adjust the amount of water as desired. Press the Rotary Switch (1) to save the new amount of water.
Turn the Rotary Switch (1) further until the next sub-item appears on the display: STRENGTH NORMAL Press the Rotary Switch (1). Turn the Rotary Switch (1) until the following message appears on the display: STRONG OK STRENGTH Press the Rotary Switch (1) to save the change.

Hot water 25 ML 450 ML

For example: Proceed as follows to change the amount of water for a coffee from 100 ML to 110 ML, to change the strength from NORMAL to STRONG and the temperature from NORMAL to HIGH. Press the Rotary Switch (1) until the following message appears on the display: RINSE Turn the Rotary Switch (1) again until the following message appears on the display: BUTTONS SELECT BUTTON Press the Rotary Switch (1).

Turn the Rotary Switch (1) further until TEMPERATURE appears on the display. Press the Rotary Switch (1). NORMAL Turn the Rotary Switch (1) to adjust the temperature.

HIGH OK TEMP.

Press the Rotary Switch to confirm your selection.
Press and hold the Rotary Switch (1) until RINSE appears on the display. The illuminated ring (2) is active. Turn the Rotary Switch (1) until ENERGY appears on the display. Press the Rotary Switch (1). SAVE Turn the Rotary Switch (1) until the following message appears on the display: SAVE OK ENERGY Press the Rotary Switch (1) again to confirm the change.
Turn the Rotary Switch (1) until EXIT appears on the display. Press the Rotary Switch (1). SELECT BUTTON
Turn the Rotary Switch (1) again until EXIT appears on the display. Press the Rotary Switch (1). BUTTONS Turn the Rotary Switch (1) again until EXIT appears on the display. Press the Rotary Switch (1) to exit programming mode. READY
Turn the Rotary Switch (1) until EXIT appears on the display. Press the Rotary Switch (1) to exit programming mode. READY
15.2 Filter programme item
For details, please refer to chapter 5.1 Inserting the filter.
15.5 Automatic switch-off time programme item 15.3 Water hardness programme item
For details, please refer to chapter 4 Adjusting the water hardness. You can program when your IMPRESSA is to switch off. Select a time between 15 min. and 15 hrs. READY Press and hold the Rotary Switch (1) until RINSE appears on the display. The illuminated ring (2) is active. Press the Rotary Switch (1) until you reach the OFF AFTER programme item.
15.4 Energy programme item
The IMPRESSA is equipped with the new On/Off button (21) (= Zero-Energy Switch). This allows the machine to be fully disconnected from the mains. An Energy Save Mode (E.S.M.) can also be permanently set.

OFF AFTER

Press the Rotary Switch (1). MANUAL Turn the Rotary Switch (1) until the following message appears on the display: AUTOMATIC OK RINSING Press the Rotary Switch (1) again to confirm the change.
Press the Rotary Switch (1) to enter the OFF AFTER programme item. 1 HRS Turn the Rotary Switch (1) to set the number of hours after which the machine is to switch off. For example 2 HRS. Press the Rotary Switch (1) to save the new automatic switch-off time. OK OFF AFTER

Turn the Rotary Switch (1) until the following message appears on the display. EXIT READY Press the Rotary Switch (1) again to exit programming mode.
15.7 Reset programme item
In the RESET programme item you can reset various settings to their factory settings: PRODUCT The settings (amount of water, strength, temperature) for any product can be reset individually to the factory settings. The corresponding double product is reset to the factory settings at the same time. ALL PROD. The settings (amount of water, strength, temperature) for all products are reset to the factory settings. RESET ALL All customer settings are reset to the factory settings. The IMPRESSA then switches off.
15.6 Rinse programme item
You can set whether the rinse should be started manually or automatically when switching on. READY Press and hold the Rotary Switch (1) until RINSE appears on the display. The illuminated ring (2) is active. Turn the Rotary Switch (1) until RINSING appears on the display.
For example you want to reset the values for one product to the factory setting: READY Press and hold the Rotary Switch (1) until RINSE appears on the display. The illuminated ring (2) is active. Turn the Rotary Switch (1) until RESET appears on the display. Press the Rotary Switch (1). PRODUCT SELECT BUTTON OK SELECT BUTTON By again pressing the appropriate preparation button, you can reset other speciality coffees to their factory setting. SELECT BUTTON Press the Rotary Switch (1).
Press the Rotary Switch (1) to exit programming mode. READY
15.8 Counter programme item
The COUNTER programme item allows you to record your consumption over a particular user-defined period. You can reset this counter to zero at any time. READY Press and hold the Rotary Switch (1) until RINSE appears on the display. The illuminated ring (2) is active. Turn the Rotary Switch (1) until COUNTER appears on the display. Press the Rotary Switch (1). XXXX (=total number of prepared speciality coffees) You can now view the following information in the Counter programme item: Number of speciality coffees prepared, by pressing the corresponding preparation button Number of powders prepared, by opening and closing the powder shaft Number of hot waters prepared, by opening and closing the hot water tap Number of steams prepared, by pressing the Steam button Press the Rotary Switch (1) after viewing. DELETE YES

Press any preparation button, e.g. 1 ESPRESSO.
Press the Rotary Switch (1) to exit the PRODUCT programming item. Turn the Rotary Switch (1) until EXIT appears on the display. Press the Rotary Switch (1). RESET Turn the Rotary Switch (1) again until EXIT appears on the display.
If you do not want to delete the counter information, turn the Rotary Switch until DELETE NO appears on the display. Press the Rotary Switch (1) again to (not) delete the counter. OK COUNTER
For example: Proceed as follows to lock a speciality coffee: READY Press and hold the Rotary Switch (1) until RINSE appears on the display. The illuminated ring (2) is active. Turn the Rotary Switch (1) until LOCK appears on the display. Press the Rotary Switch (1). BUTTONS SELECT BUTTON LOCKED SELECT Press the Rotary Switch (1) again.
Turn the Rotary Switch (1) until the following message appears on the display: EXIT READY Press the Rotary Switch (1) to exit programming mode.

15.9 Lock programme item

The LOCK programme item allows you to lock the following sub-items: any speciality coffees the aroma preselection and the amount of water adjustment during coffee preparation the cleaning, descaling and filter change maintenance functions Locking and unlocking speciality coffees, the preselection options and the maintenance functions always follows the same pattern. After the sub-item has been locked, the word LOCKED appears briefly on the display. After the sub-item has been unlocked, the word FREE appears briefly on the display.
Select the product you want to lock.
Turn the Rotary Switch (1) until EXIT appears on the display. Press the Rotary Switch (1). BUTTONS Turn the Rotary Switch (1) again until EXIT appears on the display. Press the Rotary Switch (1). LOCK Turn the Rotary Switch (1) until EXIT appears on the display. Press the Rotary Switch (1) to exit programming mode. READY
For example: Proceed as follows to cancel the lock on a speciality coffee: READY Press and hold the Rotary Switch (1) until RINSE appears on the display. The illuminated ring (2) is active. Turn the Rotary Switch (1) until LOCK appears on the display. Press the Rotary Switch (1). BUTTONS SELECT BUTTON FREE SELECT BUTTON Press the Rotary Switch (1) again.
15.10 Information programme item
In the INFORMATION programme item you can view the following information: Total coffee preparations Number of speciality coffees prepared, number of coffee powder, hot water and steam preparations Maintenance status and number of maintenance programmes performed (cleaning, descaling, changing the filter) and information relating to the software version READY Press and hold the Rotary Switch (1) until RINSE appears on the display. The illuminated ring (2) is active. Turn the Rotary Switch (1) until INFO appears on the display. Press the Rotary Switch (1). BUTTONS XXXX (=total number of speciality coffees prepared). To view the number of product preparations, press the preparation button of the desired speciality coffee. For example, to view the number of 1 COFFEE preparations. Press the 1 COFFEE preparation button. XXXX (=total number for 1 COFFEE) BUTTONS Press the Rotary Switch (1) to exit the programme item. Press the Rotary Switch (1) again.

Select the locked product you want to unlock.
Turn the Rotary Switch (1) for more information about the filter, descaling or the machine version. Turn the Rotary Switch (1) until CLEAN appears on the display for example. Press the Rotary Switch (1) to view the number of cleaning operations performed. formed) Turn the Rotary Switch (1) until the following message appears on the display: In addition to the number of maintenance programmes performed, the progress bar also shows you the current maintenance status. When the bar is completely filled, your IMPRESSA will request the respective maintenance programme. Press the Rotary Switch (1) to exit the CLEAN programme item. CLEAN Turn the Rotary Switch (1) until EXIT appears on the display. Press the Rotary Switch (1). INFO Turn the Rotary Switch (1) again until EXIT appears on the display. Press the Rotary Switch (1) again. Press the Rotary Switch (1) once more. READY XXXX (=total number of cleaning operations per-
15.11 ML/OZ display programme item
READY Press and hold the Rotary Switch (1) until RINSE appears on the display. The illuminated ring (2) is active. Turn the Rotary Switch (1) until DISPLAY appears on the Press the Rotary Switch (1). ML OZ. Turn the Rotary Switch (1) and select the desired setting. For example OK DISPLAY Press the Rotary Switch (1) to save the desired setting.
15.12 Language programme item
You can choose from the following languages: German English French Italian Dutch Spanish Portuguese Russian READY
Press and hold the Rotary Switch (1) until RINSE appears on the display. The illuminated ring (2) is active. Turn the Rotary Switch (1) until you reach the LANGUAGE programme item. LANGUAGE Press the Rotary Switch (1) to enter the LANGUAGE programme item. ENGLISH Turn the Rotary Switch (1) until the desired language appears on the display. For example OK SPRACHE DEUTSCH. Press the Rotary Switch (1) to save the language selected.
READY The water tank should be rinsed daily and filled with fresh water. Only top up with fresh, cold water. Never fill with milk, mineral water or other liquids.
16.2 Emptying coffee grounds container
EMPTY GROUNDS When this display lights up, the machine cannot prepare any more products and the coffee grounds container must be emptied (Fig. 14). Remove the drip tray (20) carefully as it will contain water. TRAY MISSING READY
Turn the Rotary Switch (1) until the following message appears on the display: EXIT BEREIT Press the Rotary Switch (1) to exit programming mode.

Fit the empty, clean drip tray back in the IMPRESSA.

16.3 Drip tray missing

TRAY MISSING
16. Maintenance 16.1 Filling with water
FILL WATER TANK When this display lights up, the machine cannot prepare any more products. Top up with water as described in chapter 2.3.
When this display lights up, the drip tray (20) has not been correctly inserted or has not been inserted at all. Insert the drip tray (20). READY
16.4 Filling with coffee beans

FILL BEANS

16.7 IMPRESSA calcification
Over time the IMPRESSA will build up limescale deposits. The degree of calcification depends on the hardness of your water. The IMPRESSA detects when it needs descaling. You can still prepare coffee or hot water/steam. We do however recommend that you undertake descaling within the next couple of days. For details, please refer to the descaling chapter (item 18). READY DE-SCALE
Top up the beans as described in chapter 2.4. The FILL BEANS display only goes out after a coffee has been prepared. We recommend that you clean the bean container with a dry cloth from time to time before refilling. Switch the IMPRESSA off to do this.
16.8 General cleaning instructions 16.5 Changing the filter
After drawing off 50 litres of water, the filter will cease to work. You will be prompted to change the filter. For details, please refer to chapter 5.2 Changing the filter. When cleaning never use objects, pan cloths or cleaning sponges which may scratch the machine or corrosive chemicals. Wipe the inside and outside of the housing with a soft, damp cloth. The machine must not be cleaned with a jet of water. Always clean the removable hot-water nozzle after use. To ensure that the Professional Cappuccino Frother always works properly, you should rinse it with water after every milk preparation. To ensure that the Professional Cappuccino Frother always works properly, you should clean it daily when you have been preparing milk. The water tank should be rinsed daily and filled with fresh water. If you can see scale starting to form in the water tank, you can use a conventional descaling agent to remove it. Remove the water tank to do this (Fig. 4). When using a Claris filter cartridge, remove this before descaling the tank.

16.6 Cleaning the IMPRESSA
After 200 preparations or 160 rinses, the IMPRESSA must be cleaned. The display will indicate this. You can still prepare coffee or hot water/steam. We do however recommend that you undertake cleaning within the next couple of days. For details, please refer to the cleaning chapter (item 17). READY CLEAN

16.9 Emptying the system

This operation is needed to protect the IMPRESSA from frost damage during transport. READY (8). HEATING READY Press the steam preselection button
Once started, the cleaning operation must not be interrupted. The filler funnel for preground coffee must be cleaned after every cleaning programme (11). READY CLEAN (3) until the following message
Press the Maintenance button appears: EMPTY TRAY TRAY MISSING

Empty the drip tray.

Remove and empty the water tank. Allow all the steam to exit the nozzle until the system is empty. CLOSE TAP (21) to switch off your IMPRESSA. Close the steam / hot water draw-off tap (14). Press the On/Off button
Carefully reinsert the drip tray. Remove the cup grille (19). Place a 1 litre receptacle (Fig. 12) under the height-adjustable coffee spout (17). PRESS RINSE (3). CLEANING ADD TABLET

17. Cleaning

The IMPRESSA machine comes with an integrated Cappuccino cleaning programme. The operation lasts about 15 minutes. The machine must not be cleaned with a jet of water. Your stockist can supply original JURA cleaning tablets which are optimised for the cleaning programme of your IMPRESSA. We would like to point out that using unsuitable cleaning tablets may damage your machine and leave traces in the water.
Add the tablet to the powder shaft (Fig. 15). Close the powder shaft. PRESS RINSE
Press the Maintenance button CLEANING EMPTY TRAY TRAY MISSING HEATING READY
When using the descaling agent, immediately clean up any splashes or drips on sensitive surfaces, especially natural stone and wooden surfaces. Alternatively take appropriate precautions. Always wait until all the added descaling agent has been used and the tank is empty. Never top up the descaling agent. READY DE-SCALE (3) until the following message

Remove and empty the drip tray.

Reinsert the drip tray.

Remove the Professional Cappuccino Frother (15) (Fig. 17). Press the Maintenance button appears: EMPTY TRAY TRAY MISSING AGENT IN TANK
Once the cleaning operation is complete, use a dry cloth to rub down the powder shaft. Cleaning is complete.

18. Descaling

The IMPRESSA machine comes with an integrated descaling programme. The operation lasts about 40 minutes. Your stockist can supply original JURA descaling tablets which are optimised for the descaling programme of your IMPRESSA. We would like to point out that using unsuitable descaling tablets may damage your machine and leave traces in the water. The display will indicate when the IMPRESSA needs descaling. You can still prepare coffee or hot water/steam and run the descaling programme later on. Once started, the descaling operation must not be interrupted.
Carefully reinsert the drip tray.
Remove and empty the water tank. Completely dissolve the contents of one blister (3 tablets) in 0.5 litres of water and add the mixture to the water tank. Reinsert the water tank. OPEN TAP AGENT IN TANK
Place a sufficiently large receptacle under the hot-water spout (Fig. 17).
Open the steam / hot water draw-off tap (14) (Fig. 13). DE-SCALING CLOSE TAP DE-SCALING EMPTY TRAY TRAY MISSING FILL WATER TANK Rinse the water tank thoroughly and fill it with cold fresh mains water. Then refit in the IMPRESSA. OPEN TAP DE-SCALING CLOSE TAP

TRAY MISSING READY

Carefully reinsert the drip tray. Descaling is complete.

19. Disposal

Please dispose of old machines in an environmentallyneutral way Old machines contain valuable, recyclable materials which should be recycled. Please therefore dispose of old machines via suitable collection systems.
20. Tips for a perfect coffee
Height-adjustable coffee spout (17) You can adjust the coffee spout to the size of your cups (Fig. 3). Consistency of grind For details, please refer to chapter 2.5 Adjusting the grinder Prewarming cups You can prewarm the cups with hot water or steam. The smaller the amount of water for coffee, the more important the prewarming process. Sugar and cream Heat will be lost when you stir the product in your cup. Adding cream or milk from the fridge greatly lowers the temperature of the coffee.
Open the steam / hot water draw-off tap (14) (Fig. 13).
Once you have closed the steam / hot water draw-off tap (14), the following appears on the display: DE-SCALING EMPTY TRAY

Empty the drip tray.

21. Messages
Cause FILL WATER TANK The water tank is empty The float is defective FILL BEANS The bean container is empty Even though the beans have been topped up, the display does not go out EMPTY GROUNDS Coffee grounds container full Drip tray inserted too soon after emptying TRAY MISSING READY CLEAN READY DE-SCALE READY FILTER ERROR Drip tray not inserted correctly or missing Cleaning needed Descaling needed Filter has ceased working General fault Remedy Fill the water tank Rinse or descale the water tank Fill with beans Prepare a cup of coffee. The Fill beans message only disappears after you have prepared a coffee Empty coffee grounds container Wait 10 sec. before inserting drip tray Insert correctly Perform cleaning operation (chapter 17) Perform descaling operation (chapter 18) Change filter (chapter 5.2) Disconnect IMPRESSA from mains Have IMPRESSA checked by JURA customer support You will find contact details for your country at www.jura.com.

Technical Data

IMPRESSA XF50
IMPRESSA key technologies and standards Intelligent Pre Brew Aroma System (I.P.B.A.S.) I.P.W.S. compatible Two cups in a single brewing operation Six-setting grinder High-performance pump, 15 bar Additional pre-ground coffee blend Recognition of de-scaling Seven-language display dialogue system Hot water and steam function Mains switch
Programming Ajustable water hardness Programmable brewing temperature Amount of water programmable

JURA Elektroapparate AG

Since our products are constantly updated with the latest technology, it is possible that some of the technical data in this sheet does not correspond with your actual machine. The same may be true for the colour of your machine.
Programmable automatic switch-off Programmable automatic switch-on time Integrated rinsing-, cleaning- and de-scaling-programme
Capacity: Daily capacity Volume of bean container Volume of grounds container (portions) Volume of water tank approx. 30 cups 200 g ca. 30 3.2 l
Facts: Variable-volume brewing unit Height-adjustable dual-purpose dispenser Weight Dimensions (W x H x D) Cable length Voltage Power Testing 5 - 16 g 70-111 mm 11 kg 32.5 x 37.5 x 47 cm 1.1 m 230 V AC 1450 W
Article number Swiss made 13266