SCHEMATIC DIAGRAMS

COLOUR TELEVISION

AV-28KT1BUF/A, /B, /C, AV-28KT1SUF/A, /B, /C

CD-ROM No.SML200310

RM-C1100 TV
COPYRIGHT 2003 VICTOR COMPANY OF JAPAN, LIMITED

No.52137 2003/10

AV-28KT1BUF AV-28KT1SUF

CONTENTS

SEMICONDUCTOR SHAPES BLOCK DIAGRAM CIRCUIT DIAGRAMS
MAIN PWB CIRCUIT DIAGRAM CRT SOCKET PWB CIRCUIT DIAGRAM SIDE CONTROL PWB CIRCUIT DIAGRAM LED PWB CIRCUIT DIAGRAM SWITCH PWB CIRCUIT DIAGRAM

2-2 2-3

AV-28KT1BUF/A/B/C AV-28KT1SUF/A/B/C

STANDARD CIRCUIT DIAGRAM

2-5 2-15 2-17 2-19 2-20
NOTE ON USING CIRCUIT DIAGRAMS

1.SAFETY

The components identified by the symbol and shading are critical for safety. For continued safety replace safety critical components only with manufactures recommended parts. Withstand voltage No indication Others :DC50[V] :DC withstand voltage [V]

PATTERN DIAGRAMS

MAIN PWB PATTERN CRT SOCKET PWB PATTERN SIDE CONTROL PWB PATTERN LED PWB PATTERN SWITCH PWB PATTERN

2-21 2-23 2-24 2-25 2-26

2.SPECIFIED VOLTAGE AND WAVEFORM VALUES
The voltage and waveform values have been measured under the following conditions. (1)Input signal (2)Setting positions of each knob/button and variable resistor (3)Internal resistance of tester (4)Oscilloscope sweeping time : Colour bar signal
AC indicated :AC withstand voltage [V] Electrolytic Capacitors 47/50[Example]:Capacitance value [F]/withstand voltage[V] Type No indication MM PP MPP MF TF BP TAN (3)Coils No unit Others :[ H] :As specified :Ceramic capacitor :Metalized mylar capacitor :Polypropylene capacitor :Metalized polypropylene capacitor :Metalized film capacitor :Thin film capacitor :Bipolar electrolytic capacitor :Tantalum capacitor
: Original setting position when shipped :DC 20k :H :V :Others /V 20S/div 5mS/div Sweeping time is specified

SEMICONDUCTOR SHAPES

TRANSISTOR
BOTTOM VIEW FRONT VIEW TOP VIEW CHIP TR

(5)Voltage values

:All DC voltage values
Since the voltage values of signal circuit vary to some extent according to adjustments, use them as reference values.

B C E (G)(D)(S)

4.NOTE FOR REPAIRING SERVICE
This model's power circuit is partly different in the GND. The difference of the GND is shown by the LIVE side GND and the ISOLATED(NEUTRAL) side GND.Therefore, care must be taken for the following points. (1)Do not touch the LIVE side GND or the LIVE side GND and the ISOLATED(NEUTRAL) side GND simultaneously. If the above caution is not respected, an electric shock may be caused. Therefore, make sure that the power cord is surely removed from the receptacle when, for example, the chassis is pulled out. (2)Do not short between the LIVE side GND and ISOLATED(NEUTRAL) side GND or never measure with a measuring apparatus measure with a measuring apparatus ( oscilloscope, etc.) the LIVE side GND and ISOLATED(NEUTRAL) side GND at the same time. If the above precaution is not respected , a fuse or any parts will be broken. Since the circuit diagram is a standard one, the circuit and circuit constants may be subject to change for improvement without any notice. NOTE Due improvement in performance, some part numbers show in the circuit diagram may not agree with those indicated in the part list. When ordering parts, please use the numbers that appear in the Parts List.

3.INDICATIONS ON THE CIRCUIT DIAGRAM
BOTTOM VIEW FRONT VIEW TOP VIEW
(1)Resistors Resistance value No unit

K M Type No indication

:[ ] :[K ] :[M ]

OUT E IN

IN E OUT
:Carbon resistor :Oxide metal film resistor :Metal film resistor :Metal plate resistor :Uninflammable resistor :Fusible resistor

OMR MFR MPR UNFR

CHIP IC

TOP VIEW

FR (2)Capacitors Capacitance value 1 or higher less than 1
Composition resistor 1/2 [W] is specified as 1/2S or Comp.

:[pF] :[F]

No.52137

Sep. 2003 No. 52137

BLOCK DIAGRAM

SC3_V_OUT CVBS

RGB AMPLIFIER

SAW Filter

SC1_V_OUT

38.9MHz-TV TUNER

R G B FB R Horizontal Vertical Stage

VDP313XY

SC1_RGB

SC2_RGB/DVD/DVB

SDA SCL SC1 SC2 IF SVHS-Y SC3 EXT_CVBS/Y SC2_V_OUT SCL SDA SYNC

VIDEO SW

TO_PIP

CVBS_TEXT

TV_LINK SDA

(MicroController)

OSD_B OSD_FBL

(E2PROM) SCL L

SCL SDA SC1 SC2 FRONT/SC3 DVD/DVB/BAV R

Headphone

8 ohm 12W

AUDIO AMPLIFIER

CIRCUIT DIAGRAMS
MAIN PWB CIRCUIT DIAGRAM [1/5]

CRT SOCKET PWB

MAIN PWB (1/5)
VE-20120604 (AV-28KT1BUF/A, AV-28KT1SUF/A) VE-20127801 (AV-28KT1BUF/B, AV-28KT1SUF/B) VE-20127796 (AV-28KT1BUF/C, AV-28KT1SUF/C)

SIDE CONTROL PWB

MAIN PWB CIRCUIT DIAGRAM [2/5]

LED PWB

MAIN PWB (2/5)
DIFFERENCE LIST MAIN PWB AV-28KT1BUF/A, AV-28KT1SUF/A AV-28KT1BUF/B, AV-28KT1SUF/B AV-28KT1BUF/C, AV-28KT1SUF/C VE-20120604 VE-20127801 VE-20127796 IC 500 VE-20139901 VE-20137151 VE-20139902 IC 502 VE-20120610 VE-20134092 VE-20126318
MAIN PWB CIRCUIT DIAGRAM [3/5]

MAIN PWB (3/5)

MAIN PWB CIRCUIT DIAGRAM [4/5]

MAIN PWB (4/5)

MAIN PWB CIRCUIT DIAGRAM [5/5]

AC INPUT

MAIN PWB (5/5)

DEG.COIL

CRT SOCKET PWB CIRCUIT DIAGRAM

VE-20121506

MAIN PWB
SIDE CONTROL PWB CIRCUIT DIAGRAM

SPEAKER LEFT

MAIN PWB SPEAKER RIGHT

VE-20120893

LED PWB CIRCUIT DIAGRAM
SWITCH PWB CIRCUIT DIAGRAM

VE-20119110

SWITCH PWB

VE-20122229

MAIN PWB PATTERN

CRT SOCKET PWB PATTERN

SIDE CONTROL PWB PATTERN

LED PWB PATTERN

POWER SWITCH PWB PATTERN

WPC0309 DP8080

PARTS LIST
! USING PW BOARD & REMOTE CONTROL UNIT 3-1 ! EXPLODED VIEW PARTS LIST 3-2 ! EXPLODED VIEW 3-3 ! PRINTED WIRING BOARD PARTS LIST [ AV-28KT1BUF/A , AV-28KT1SUF/A ] " MAIN PW BOARD ASS'Y 3-4 " CRT SOCKET PW BOARD ASS'Y (COMMON) 3-8 " SIDE CONTROL PW BOARD ASSY (COMMON) 3-8 " LED PW BOARD ASSY (COMMON) 3-8 " SWITCH PW BOARD ASSY (COMMON) 3-8 [ AV-28KT1BUF/B , AV-28KT1SUF/B ] " MAIN PW BOARD ASS'Y 3-9 [ AV-28KT1BUF/C , AV-28KT1SUF/C ] " MAIN PW BOARD ASS'Y 3-9 ! PACKING / PACKING PARTS LIST 3-10
USING PW BOARD & REMOTE CONTROL UNIT

Model PWB ASS'Y

AV-28KT1BUF/A AV-28KT1SUF/A

[A-VERSION]

AV-28KT1BUF/B AV-28KT1SUF/B

[B-VERSION]

AV-28KT1BUF/C AV-28KT1SUF/C

[C-VERSION]

MAIN PWB CRT SOCKET PWB SIDE CONTROL PWB LED PWB SWITCH PWB REMOTE CONTROL UNIT
VE-20120604 VE-20121506 VE-20120893 VE-20129110 VE-20122229 VE-30017763 (RM-C1100)

VE-20127801

VE-20127796

No. 52137

EXPLODED VIEW PARTS LIST
! Ref.No. Part No. Part Name Description
[ AV-28KT1BUF : BLACK model ]
! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! V01 L01 TRVE-30002751 VE-30002138 VE-30021290 VE-20121492 VE-20091798 VE-40013592 VE-20111864 VE-35000013 VE-20094352 VE-20056446 VE-30001946 VE-20093231 VE-30015614 VE-20108124 VE-20121494 VE-20127842 VE-20127843 VE-20127874 VE-20127871 VE-30016513 VE-20110931 VE-40014391 VE-20004520 VE-35000211 VE-35004572 VE-20081578 PICTURE TUBE DEG COIL&EARTH FB TRANSF. FRONT CABINET FUNCTION BUTTON LOGO JVC ON/OFF BUTTON (POWER) SPRING (ON/OFF SWITCH) PRE-AMP LENS LED LENS SPEAKER CHASSIS FRAME PFC TRANSF. BACK DOOR BACK COVER LABEL LABEL LABEL LABEL POWER CORD (2.2MT) BACK COVER HOLDER FOOT RUBBER CABLE HOLDER SCREW (2.9*9.5) SCREW (4x20) BASE Inc. DY, PC MAGNET Within MAIN PWB

(x2) 8R 15W 57*160

[A-VERSION] [A-VERSION] [B-VERSION] [C-VERSION] (x2) (x2) (x4) For BACK DOOR (x8) For BACK COVER

! Ref.No.

Part No.

Part Name

Description
[ AV-28KT1SUF : SILVER model ]
! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! V01 L01 TRVE-30002751 VE-30002138 VE-30021290 VE-20119985 VE-20096498 VE-40013593 VE-20120046 VE-35000013 VE-20094352 VE-20056446 VE-30001946 VE-20093231 VE-30015614 VE-20120043 VE-20111863 VE-20127776 VE-20127777 VE-20127841 VE-20127894 VE-30016513 VE-20110931 VE-40014391 VE-20004520 VE-35000211 VE-35004572 VE-20081578 PICTURE TUBE DEG COIL&EARTH FB TRANSF. FRONT CABINET FUNCTION BUTTON LOGO JVC ON/OFF BUTTON (POWER) SPRING (ON/OFF SWITCH) PRE-AMP LENS LED LENS SPEAKER CHASSIS FRAME PFC TRANSF. BACK DOOR BACK COVER LABEL LABEL LABEL LABEL POWER CORD (2.2MT) BACK COVER HOLDER FOOT RUBBER CABLE HOLDER SCREW (2.9*9.5) SCREW (4x20) BASE Inc. DY, PC MAGNET Within MAIN PWB

EXPLODED VIEW

PRINTED WIRING BOARD PARTS LIST
[ AV-28KT1BUF/A / AV-28KT1SUF/A ]
!MAIN P.W. BOARD ASSY (VE-20120604)
! Symbol No. C202 L240 L241 L242 L268 R100 R101 R105 R106 R108 R110 R112 R114 R116 ! R117 R118 R119 R122 R126 R127 R129 R130 R131 R132 R133 R134 R137 R138 R139 R140 R141 R142 R143 R144 R145 R146 R147 R148 R149 R150 R151 ! R152 R153 R154 R155 R156 R157 R158 R161 R162 R164 R165 R166 R200 R201 R202 R203 R204 R205 R206 R207 R208 R209 R210 R211 R215 R219 R220 R221 R222 R230 R231 R232 R233 R234 R235 R236 R237 R238 R239 R241 R242 R247 R248 R254 R256 Part No. VE-30012643 VE-30000464 VE-30000464 VE-30000464 VE-30000614 VE-30000718 VE-30000896 VE-30000982 VE-30000593 VE-30000452 VE-30012657 VE-30012657 VE-30007784 VE-30001173 VE-30001257 VE-30000580 VE-30012641 VE-30014022 VE-30012641 VE-30012692 VE-30012692 VE-30012641 VE-30000466 VE-30000466 VE-30000513 VE-30000575 VE-30000481 VE-30000660 VE-30000593 VE-30015222 VE-30012641 VE-30012657 VE-30020455 VE-30000480 VE-30020457 VE-30012697 VE-30020455 VE-30020457 VE-30012657 VE-30000466 VE-30012641 VE-30001224 VE-30012692 VE-30012641 VE-30012641 VE-30012641 VE-30012641 VE-30012657 VE-30012657 VE-30000494 VE-30000593 VE-30001159 VE-30012641 VE-30012713 VE-30012713 VE-30012713 VE-30012713 VE-30012713 VE-30012713 VE-30000459 VE-30000459 VE-30012510 VE-30012510 VE-30012662 VE-30012657 VE-30012713 VE-30000792 VE-30012641 VE-30000792 VE-30012641 VE-30012641 VE-30000792 VE-30012713 VE-30012657 VE-30012702 VE-30000655 VE-30012713 VE-30012641 VE-30012641 VE-30012713 VE-30012510 VE-30012696 VE-30000500 VE-30012641 VE-30012657 VE-30012655 Part Name SMD R SMD R SMD R SMD R SMD R CF R MF R MF R SMD R CF R SMD R SMD R MO R MO R MG R CF R SMD R SMD R SMD R SMD R SMD R SMD R CF R CF R CF R SMD R CF R CF R SMD R MO R SMD R SMD R SMD R SMD R SMD R SMD R SMD R SMD R SMD R CF R SMD R FUSE R SMD R SMD R SMD R SMD R SMD R SMD R SMD R SMD R SMD R MO R SMD R SMD R SMD R SMD R SMD R SMD R SMD R CF R CF R SMD R SMD R SMD R SMD R SMD R CF R SMD R CF R SMD R SMD R CF R SMD R SMD R SMD R CF R SMD R SMD R SMD R SMD R SMD R SMD R CF R SMD R SMD R SMD R Description 1/16W 120R J 1/10W 100R J 1/10W 100R J 1/10W 100R J 1/10W 2.4K J 1/4W 4.7K J 1/4W 160K G 1/4W 4.7K J 1/10W 2.2K J 1/4W 10R J 1/16W 1K J 1/16W 1K J 5W 33K J(RADIAL) 1W 0.47R J 1/2W 4.7M J 1/4W 22R J 1/16W 10K J 1/16W 47R J 1/16W 10K J 1/16W 4.7K J 1/16W 4.7K J 1/16W 10K J 1/4W 1K J 1/4W 1K J 1/4W 130K J 1/10W 2K J 1/4W 1M J 1/4W 3.3K J 1/10W 2.2K J 1W 0.75R J 1/16W 10K J 1/16W 1K J 1/16W 1.5K F 1/10W 100K J 1/16W 910R F 1/16W 5.1K J 1/16W 1.5K F 1/16W 910R F 1/16W 1K J 1/4W 1K J 1/16W 10K J 1/2W 0.22R J 1/16W 4.7K J 1/16W 10K J 1/16W 10K J 1/16W 10K J 1/16W 10K J 1/16W 1K J 1/16W 1K J 1/10W 120R J 1/10W 2.2K J 1W 0.33R J 1/16W 10K J 1/16W 75R J 1/16W 75R J 1/16W 75R J 1/16W 75R J 1/16W 75R J 1/16W 75R J 1/4W 100R J 1/4W 100R J 1/16W 100R J 1/16W 100R J 1/16W 2.7K J 1/16W 1K J 1/16W 75R J 1/4W 75R J 1/16W 10K J 1/4W 75R J 1/16W 10K J 1/16W 10K J 1/4W 75R J 1/16W 75R J 1/16W 1K J 1/16W 560R J 1/4W 330R J 1/16W 75R J 1/16W 10K J 1/16W 10K J 1/16W 75R J 1/16W 100R J 1/16W 47K J 1/4W 12K J 1/16W 10K J 1/16W 1K J 1/16W 180R J ! Symbol No. R259 R260 R261 R264 R265 R266 R267 R268 R269 R270 R272 R273 R274 R276 R277 R278 R279 R280 R281 R282 R283 R284 R285 R286 R288 R289 R299 R308 R310 R316 R317 R318 R326 R327 R330 R334 R336 R337 R338 R342 R343 R349 R350 R351 R352 R353 R354 R355 R356 R357 R358 R359 R400 R404 R406 R409 R410 R411 R412 R413 R414 R415 R416 R417 R418 R419 R420 R421 R422 R423 R424 R425 R426 R503 R504 R505 R506 R507 R508 R509 R510 R512 R513 R516 R518 R519 Part No. VE-30000593 VE-30012669 VE-30012677 VE-30012705 VE-30000459 VE-30000459 VE-30012657 VE-30012641 VE-30012641 VE-30012641 VE-30012713 VE-30012713 VE-30012702 VE-30000593 VE-30012679 VE-30012713 VE-30012713 VE-30012713 VE-30012673 VE-30012668 VE-30012707 VE-30012684 VE-30012707 VE-30012707 VE-30000770 VE-30012707 VE-30012510 VE-30012641 VE-30012713 VE-30012641 VE-30000792 VE-30012657 VE-30000815 VE-30000480 VE-30012657 VE-30012713 VE-30000466 VE-30000466 VE-30000466 VE-30012657 VE-30012692 VE-30012641 VE-30012510 VE-30012510 VE-30012698 VE-30012685 VE-30012677 VE-30012643 VE-30012707 VE-30012644 VE-30012655 VE-30012669 VE-30012669 VE-30012692 VE-30012650 VE-30012713 VE-30012713 VE-30012657 VE-30012657 VE-30012713 VE-30012713 VE-30012679 VE-30012695 VE-30012695 VE-30012695 VE-30012695 VE-30012695 VE-30012695 VE-30012695 VE-30012695 VE-30012695 VE-30012695 VE-30012695 VE-30012510 VE-30012510 VE-30000471 VE-30000471 VE-30012696 VE-30012696 VE-30012696 VE-30012696 VE-30012668 VE-30012662 VE-30012692 VE-30012662 VE-30000466 Part Name SMD R SMD R SMD R SMD R CF R CF R SMD R SMD R SMD R SMD R SMD R SMD R SMD R SMD R SMD R SMD R SMD R SMD R SMD R SMD R SMD R SMD R SMD R SMD R CF R SMD R SMD R SMD R SMD R SMD R CF R SMD R CF R SMD R SMD R SMD R CF R CF R CF R SMD R SMD R SMD R SMD R SMD R SMD R SMD R SMD R SMD R SMD R SMD R SMD R SMD R SMD R SMD R SMD R SMD R SMD R SMD R SMD R SMD R SMD R SMD R SMD R SMD R SMD R SMD R SMD R SMD R SMD R SMD R SMD R SMD R SMD R SMD R SMD R CF R CF R SMD R SMD R SMD R SMD R SMD R SMD R SMD R SMD R CF R Description 1/10W 2.2K 1/16W 22K 1/16W 3.3K 1/16W 6.8K 1/4W 100R 1/4W 100R 1/16W 1K 1/16W 10K 1/16W 10K 1/16W 10K 1/16W 75R 1/16W 75R 1/16W 560R 1/10W 2.2K 1/16W 3.9K 1/16W 75R 1/16W 75R 1/16W 75R 1/16W 270R 1/16W 220R 1/16W 680R 1/16W 330R 1/16W 680R 1/16W 680R 1/4W 680R 1/16W 680R 1/16W 100R 1/16W 10K 1/16W 75R 1/16W 10K 1/4W 75R 1/16W 1K 1/4W 8.2K 1/10W 100K 1/16W 1K 1/16W 75R 1/4W 1K 1/4W 1K 1/4W 1K 1/16W 1K 1/16W 4.7K 1/16W 10K 1/16W 100R 1/16W 100R 1/16W 5.6K 1/16W 33K 1/16W 3.3K 1/16W 120R 1/16W 680R 1/16W 12K 1/16W 180R 1/16W 22K 1/16W 22K 1/16W 4.7K 1/16W 15K 1/16W 75R 1/16W 75R 1/16W 1K 1/16W 1K 1/16W 75R 1/16W 75R 1/16W 3.9K 1/16W 470R 1/16W 470R 1/16W 470R 1/16W 470R 1/16W 470R 1/16W 470R 1/16W 470R 1/16W 470R 1/16W 470R 1/16W 470R 1/16W 470R 1/16W 100R 1/16W 100R 1/4W 10K 1/4W 10K 1/16W 47K 1/16W 47K 1/16W 47K 1/16W 47K 1/16W 220R 1/16W 2.7K 1/16W 4.7K 1/16W 2.7K 1/4W 1K J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J

RESISTOR

! Symbol No. R520 R521 R522 R523 R524 R526 R527 R528 R533 R535 R537 R538 R539 R540 R541 R545 R546 R547 R548 R549 R550 R553 R554 R555 R560 R561 R564 R565 R566 R567 R568 R571 R582 R584 R585 R586 R587 R588 R589 R590 R600 R601 R603 R604 R605 R607 R608 R611 R612 R613 R614 R616 R621 R622 R623 R624 R625 R626 R627 R628 R629 R630 R631 R632 R636 R637 R638 R639 R640 R644 R645 R646 R647 R648 R649 R650 R652 R653 R654 R655 R656 R657 R658 R700 R701 R702 R703 R704 R705 R710 R713 R714 R715 R718 Part No. VE-30012650 VE-30012679 VE-30012692 VE-30012712 VE-30012679 VE-30012679 VE-30012679 VE-30012650 VE-30012685 VE-30012641 VE-30000466 VE-30012508 VE-30012508 VE-30012508 VE-30012662 VE-30012696 VE-30000471 VE-30012510 VE-30012641 VE-30012657 VE-30012679 VE-30012695 VE-30012692 VE-30012506 VE-30012641 VE-30012510 VE-30012692 VE-30012510 VE-30012641 VE-30000459 VE-30000459 VE-30012657 VE-30012641 VE-30012696 VE-30012641 VE-30012641 VE-30012641 VE-30012641 VE-30012641 VE-30012679 VE-30012510 VE-30000470 VE-30001244 VE-30001244 VE-30000665 VE-30012695 VE-30001100 VE-30001244 VE-30000471 VE-30001232 VE-30001244 VE-30018904 VE-30012696 VE-30012641 VE-30012641 VE-30012692 VE-30000480 VE-30012692 VE-30000480 VE-30012657 VE-30012674 VE-30000504 VE-30000504 VE-30012662 VE-30012641 VE-30012657 VE-30012674 VE-30001162 VE-30001134 VE-30000649 VE-30000580 VE-30012654 VE-30012650 VE-30012658 VE-30001228 VE-30001082 VE-30000848 VE-30012686 VE-30012674 VE-30012641 VE-30012641 VE-30000466 VE-30000466 VE-30012695 VE-30012695 VE-30012657 VE-30012510 VE-30012510 VE-30012510 VE-30012657 VE-30012510 VE-30012510 VE-30012657 VE-30012657 Part Name SMD R SMD R SMD R SMD R SMD R SMD R SMD R SMD R SMD R SMD R CF R SMD R SMD R SMD R SMD R SMD R CF R SMD R SMD R SMD R SMD R SMD R SMD R SMD R SMD R SMD R SMD R SMD R SMD R CF R CF R SMD R SMD R SMD R SMD R SMD R SMD R SMD R SMD R SMD R SMD R CF R FUSE R FUSE R CF R SMD R MO R FUSE R CF R FUSE R FUSE R MO R SMD R SMD R SMD R SMD R SMD R SMD R SMD R SMD R SMD R CF R CF R SMD R SMD R SMD R SMD R MO R MO R CF R CF R SMD R SMD R SMD R FUSE R MO R MF R SMD R SMD R SMD R SMD R CF R CF R SMD R SMD R SMD R SMD R SMD R SMD R SMD R SMD R SMD R SMD R SMD R Description 1/16W 15K 1/16W 3.9K 1/16W 4.7K 1/16W 8.2K 1/16W 3.9K 1/16W 3.9K 1/16W 3.9K 1/16W 15K 1/16W 33K 1/16W 10K 1/4W 1K 1/16W 1.8K 1/16W 1.8K 1/16W 1.8K 1/16W 2.7K 1/16W 47K 1/4W 10K 1/16W 100R 1/16W 10K 1/16W 1K 1/16W 3.9K 1/16W 470R 1/16W 4.7K 1/16W 1.5K 1/16W 10K 1/16W 100R 1/16W 4.7K 1/16W 100R 1/16W 10K 1/4W 100R 1/4W 100R 1/16W 1K 1/16W 10K 1/16W 47K 1/16W 10K 1/16W 10K 1/16W 10K 1/16W 10K 1/16W 10K 1/16W 3.9K 1/16W 100R 1/2W 10K 1/2W 0.47R 1/2W 0.47R 1/4W 33K 1/16W 470R 1W 150R 1/2W 0.47R 1/4W 10K 1/4W 2.7R 1/2W 0.47R 5W 4.7k 1/16W 47K 1/16W 10K 1/16W 10K 1/16W 4.7K 1/10W 100K 1/16W 4.7K 1/10W 100K 1/16W 1K 1/16W 27K 1/4W 120K 1/4W 120K 1/16W 2.7K 1/16W 10K 1/16W 1K 1/16W 27K 1W 390R 2W 2.2R 1/2W 33R 1/4W 22R 1/16W 180K 1/16W 15K 1/16W 1M 1/2W 2.2R 1/2W 1K 1/4W 1K 1/16W 36K 1/16W 27K 1/16W 10K 1/16W 10K 1/4W 1K 1/4W 1K 1/16W 470R 1/16W 470R 1/16W 1K 1/16W 100R 1/16W 100R 1/16W 100R 1/16W 1K 1/16W 100R 1/16W 100R 1/16W 1K 1/16W 1K J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J F J J J J J J J J J J J J J J J J J ! Symbol No. R719 R723 R724 R725 R726 R753 R755 R759 R760 R762 R763 R765 R766 R793 R794 R798 R799 R811 R815 R816 R817 R818 R819 R820 R821 VR100 Part No. VE-30012657 VE-30000459 VE-30012510 VE-30012657 VE-30012657 VE-30014076 VE-30014076 VE-30012641 VE-30012702 VE-30012641 VE-30012702 VE-30012669 VE-30012669 VE-30012695 VE-30012695 VE-30000466 VE-30012657 VE-30012641 VE-30012644 VE-30012649 VE-30012641 VE-30000723 VE-30000593 VE-30012696 VE-30012641 VE-30001064 Part Name SMD R CF R SMD R SMD R SMD R SMD R SMD R SMD R SMD R SMD R SMD R SMD R SMD R SMD R SMD R CF R SMD R SMD R SMD R SMD R SMD R CF R SMD R SMD R SMD R ADJ.R Description 1/16W 1K J 1/4W 100R J 1/16W 100R J 1/16W 1K J 1/16W 1K J 1/16W 4.7R J 1/16W 4.7R J 1/16W 10K J 1/16W 560R J 1/16W 10K J 1/16W 560R J 1/16W 22K J 1/16W 22K J 1/16W 470R J 1/16W 470R J 1/4W 1K J 1/16W 1K J 1/16W 10K J 1/16W 12K J 1/16W 150R J 1/16W 10K J 1/4W 47K J 1/10W 2.2K J 1/16W 47K J 1/16W 10K J 1/10W 470R VER (MAN) RESISTOR RESISTOR

TRANSF ! TR100 ! TR600 TR601 VE-30019432 VE-30021290 VE-30002090 SMPS TRANSF. FB TRANSF. LINE DRIVER
! Symbol No. COIL J344 L103 L105 L203 L206 L207 L263 L264 L265 L266 L500 L501 L502 L503 L504 L505 L506 L601 L700 L701 L702 L703 L711 L717 VE-30001996 VE-30001992 VE-30011450 VE-30001996 VE-30001979 VE-30001979 VE-30001979 VE-30001979 VE-30001979 VE-30001987 VE-30001992 VE-30001992 VE-30001992 VE-30001992 VE-30001992 VE-30001992 VE-30006770 VE-30002031 VE-30001996 VE-30001996 VE-30001996 VE-30001996 VE-30001996 VE-30001979 FIXED COIL FIXED COIL FIXED COIL FIXED COIL FIXED COIL FIXED COIL FIXED COIL FIXED COIL FIXED COIL FIXED COIL FIXED COIL FIXED COIL FIXED COIL FIXED COIL FIXED COIL FIXED COIL FIXED COIL INJECTION FIXED COIL FIXED COIL FIXED COIL FIXED COIL FIXED COIL FIXED COIL FIXED COIL 22UH 10UH 22UH 22UH 1UH 1UH 1UH 1UH 1UH 4.7UH 10UH 10UH 10UH 10UH 10UH 10UH 0.22UH 15MH 22UH 22UH 22UH 22UH 22UH 1UH Part No. Part Name Description ! Symbol No. Q114 Q200 Q201 Q202 Q203 Q208 Q216 Q218 Q220 Q221 Q222 Q500 Q501 Q502 Q503 Q504 Q505 Q508 Q510 Q511 Q512 Q513 Q600 Q601 ! Q602 Q603 Q605 Q606 Q700 Q703 Q704 IC ! IC100 IC101 IC102 IC103 IC104 IC106 IC116 IC200 IC201 IC206 IC301 IC500 IC502 IC600 IC601 IC700 VE-30015087 VE-30001622 VE-30001668 VE-30001668 VE-30001500 VE-30011968 VE-30001506 VE-30019492 VE-30001619 VE-30021083 VE-30016113 VE-20139901 VE-20120610 VE-30007793 VE-30001506 VE-30013658 I.C. I.C. I.C. I.C. I.C. I.C. I.C. I.C. I.C. I.C. I.C. I.C.(MICOM) [A-VERSION] PR.IC.45-SDA55XX FLASH JVC JA100 I.C.(MEMORY) [A-VERSION] IC 24C16 V008D4313A01040100122 I.C. I.C. I.C. Part No. VE-30001457 VE-30001457 VE-30001457 VE-30001457 VE-30001457 VE-30001457 VE-30001457 VE-30001458 VE-30001457 VE-30001457 VE-30001457 VE-30001457 VE-30001457 VE-30001457 VE-30001457 VE-30001457 VE-30001458 VE-30001457 VE-30001457 VE-30001457 VE-30001457 VE-30001458 VE-30001429 VE-30001435 VE-30001441 VE-30001458 VE-30001458 VE-30001458 VE-30001458 VE-30001458 VE-30001457 Part Name SMD TRANSISTOR SMD TRANSISTOR SMD TRANSISTOR SMD TRANSISTOR SMD TRANSISTOR SMD TRANSISTOR SMD TRANSISTOR SMD TRANSISTOR SMD TRANSISTOR SMD TRANSISTOR SMD TRANSISTOR SMD TRANSISTOR SMD TRANSISTOR SMD TRANSISTOR SMD TRANSISTOR SMD TRANSISTOR SMD TRANSISTOR SMD TRANSISTOR SMD TRANSISTOR SMD TRANSISTOR SMD TRANSISTOR SMD TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR SMD TRANSISTOR SMD TRANSISTOR SMD TRANSISTOR SMD TRANSISTOR SMD TRANSISTOR SMD TRANSISTOR Description TRANSISTOR

DIODE D100 ! D101 D103 D104 D105 D106 D108 D110 D111 D112 D113 D114 D118 D119 D125 D127 D129 D130 D131 D132 D133 D134 D200 D204 D212 D213 D214 D215 D216 D506 D601 D602 D603 D604 D609 D610 D611 D612 D613 D614 D615 D617 D622 D623 D624 D625 D627 D701 D702 D706 D707 VE-30001329 VE-20108354 VE-30001318 VE-30001318 VE-30001318 VE-30001344 VE-30001315 VE-30001288 VE-30001318 VE-30001285 VE-30003720 VE-30001285 VE-30009366 VE-30009366 VE-30001285 VE-30001315 VE-30001285 VE-30001329 VE-30001318 VE-30001285 VE-30003722 VE-30001285 VE-30001285 VE-30001285 VE-30001285 VE-30012411 VE-30007763 VE-30007763 VE-30007763 VE-30012412 VE-30001377 VE-30001318 VE-30001299 VE-30001299 VE-30001318 VE-30001318 VE-30007681 VE-30001285 VE-30001291 VE-30007763 VE-30001318 VE-30001285 VE-30001285 VE-30001285 VE-30001285 VE-30001320 VE-30001284 VE-30007761 VE-30001285 VE-30001285 VE-30001285 DIODE BRIDGE DIODE DIODE DIODE DIODE ZENER DIODE DIODE DIODE DIODE SMD DIODE SMD ZENER DIODE SMD DIODE DIODE DIODE SMD DIODE DIODE SMD DIODE DIODE DIODE SMD DIODE ZENER DIODE SMD DIODE SMD DIODE SMD DIODE SMD DIODE SMD DIODE SMD ZENER DIODE SMD ZENER DIODE SMD ZENER DIODE SMD ZENER DIODE UZT ZENER DIODE DIODE DIODE DIODE DIODE DIODE DIODE SMD DIODE DIODE SMD ZENER DIODE DIODE SMD DIODE SMD DIODE SMD DIODE SMD DIODE DIODE DIODE SMD ZENER DIODE SMD DIODE SMD DIODE SMD DIODE 1A/1000V 30A 4A/1000V 150A(FORMLU) 1A/800V 20A 1A/800V 20A 1A/800V 20A 6.2V 1/2W 1A/200V 20A 2A/200V 50A 1A/800V 20A 3.3V 3A/200V 150A 3A/200V 150A 1A/200V 20A 1A/1000V 30A 1A/800V 20A
OTHERS 2.4V 33V 1A/800V 20A 3A/400V 150A 3A/400V 150A 1A/800V 20A 1A/800V 20A 3A/800V 150A 1A/800V 30A 1A/800V 20A ! L101 L102 L212 L213 L214 L215 L216 L217 L218 L220 L227 L232 L236 L239 L247 L251 L252 L719 ! TH100 ! TU200 X200 X201 X500 X700 Z200 Z201 VE-30018866 VE-30001971 VE-30001971 VE-30001971 VE-30001971 VE-30001971 VE-30001971 VE-30001971 VE-30001971 VE-30001971 VE-30001971 VE-30001971 VE-30001971 VE-30001971 VE-30001971 VE-30001971 VE-30001971 VE-30001968 VE-30001270 VE-30009637 VE-30002851 VE-30008778 VE-30006662 VE-30001756 VE-30014261 VE-30012545 LINE FILTER FERRITE BEAT FERRITE BEAT FERRITE BEAT FERRITE BEAT FERRITE BEAT FERRITE BEAT FERRITE BEAT FERRITE BEAT FERRITE BEAT FERRITE BEAT FERRITE BEAT FERRITE BEAT FERRITE BEAT FERRITE BEAT FERRITE BEAT FERRITE BEAT FERRITE BEAD PTC TUNER XTAL XTAL XTAL XTAL SAW FILTER SAW FILTER

CAPACITOR C900 C902 C903 C904 C905 C906 C909 C910 C913 C914 C915 C916 C918 C919 C920 C921 C931 S4 COIL L901 VE-30001994 FIXED COIL 22UH J AXIAL VE-30000075 VE-30000415 VE-30000438 VE-30000287 VE-30000350 VE-30000075 VE-30000407 VE-30000294 VE-30000294 VE-30012577 VE-30000407 VE-30000352 VE-30012577 VE-30012577 VE-30012577 VE-30000294 VE-30000075 VE-30016654 MKT CAP. EL CAP. CER CAP. CER CAP. EL CAP. MKT CAP. EL CAP. SMD CAP. SMD CAP. SMD CAP. EL CAP. EL CAP. SMD CAP. SMD CAP. SMD CAP. SMD CAP. MKT CAP. SMD CAP. 100NF 250V K (DC) 4.7UF 250V M 2.2NF 2KV 10NF 50V K B 10UF 250V M 100NF 250V K (DC) 470UF 16V M 100NF 50V K 100NF 50V K 560PF 50V J 470UF 16V M 100UF 16V M 560PF 50V J 560PF 50V J 560PF 50V J 100NF 50V K 100NF 250V K (DC) 100NF 16V K R
!LED PW BOARD ASSY (VE-20119110)
! Symbol No. D100 D100 Part No. VE-30001279 VE-20119034 Part Name LED(RED/GREEN) LED HOLDER Description DIODE
OTHERS DIODE D902 D903 D904 D905 D907 D908 D909 VE-30001318 VE-30001284 VE-30001318 VE-30001318 VE-30001318 VE-30014353 VE-30001285 DIODE DIODE DIODE DIODE DIODE DIODE SMD DIODE 1A/800V 20A 0.15A/100V 0.5A 1A/800V 20A 1A/800V 20A 1A/800V 20A MD101 VE-30001670 PREAMPLIFIER
!SWITCH PW BOARD ASSY (VE-20122229)
! Symbol No. ! F801 ! SW800 Part No. VE-30001731 VE-30022450 Part Name FUSE SWITCH(ON/OFF) Description 2.5A OTHERS
TRANSISTOR Q900 Q901 Q902 Q903 Q904 IC IC900 IC901 VE-30015857 VE-30014346 I.C. I.C. VE-30001427 VE-30001458 VE-30001458 VE-30001458 VE-30001458 TRANSISTOR SMD TRANSISTOR SMD TRANSISTOR SMD TRANSISTOR SMD TRANSISTOR
OTHERS ! PL901 SG901 SG902 SG903 SG904 SG905 VE-30001855 VE-30000428 VE-30000428 VE-30000428 VE-30000428 VE-30021532 CRT SOCKET SPARK GAP SPARK GAP SPARK GAP SPARK GAP SPARK GAP 300V 300V 300V 300V 1500V
[ AV-28KT1BUF/B / AV-28KT1SUF/B ]
!MAIN P.W. BOARD ASSY (VE-20127801)
Regarding the parts list for the main PW board assy VE-20127801, only the different parts from those of the VE-20120604 are described, For further details regarding the other parts, refer to the parts list for the VE-20120604 described on page 4 through page 7. Part No. ! Symbol No. IC500 IC502

VE-20120604

[A-VERSION] VE-20139901 VE-20120610
[B-VERSION] VE-20137151 VE-20134092
Part Name I.C. (MICOM) I.C. (MEMORY)
Description [B-VERSION] [B-VERSION]
Refer to PARTS LIST in page 8 for this P. W. board.
[ AV-28KT1BUF/C / AV-28KT1SUF/C ]
!MAIN P.W. BOARD ASSY (VE-20127796)
Regarding the parts list for the main PW board assy VE-20127796, only the different parts from those of the VE-20120604 are described, For further details regarding the other parts, refer to the parts list for the VE-20120604 described on page 4 through page 7. Part No. ! Symbol No. IC500 IC502
[C-VERSION] VE-20139902 VE-20126318
Description [C-VERSION] [C-VERSION]

PACKING

4 ! ! 7 ! 8 9

! 10 2

PACKING PARTS LIST
10 VE-50038917 VE-50038933 VE-50038949 VE-20116671 VE-50026637 VE-70000587 VE-30017763 VE-50038905 VE-50038931 VE-50038935 BT-54013-2TK VE-20127842 VE-20127843 VE-20127874 VE-20127871 CARTON BOX CARTON BOX CARTON BOX SNOW BOX ASSY POLY BAG (1250*1000) POLY BAG REMOTE CONTROL UNIT INST BOOK INST BOOK INST BOOK WARRANTY CARD LABEL LABEL LABEL LABEL [A-VERSION] [B-VERSION] [C-VERSION] 4 pcs in 1set (RM-C1100) [A-VERSION] [B-VERSION] [C-VERSION] [A-VERSION] [A-VERSION] [B-VERSION] [C-VERSION]

! ! ! ! ! ! !

10 VE-50038907 VE-50038932 VE-50038950 VE-20116671 VE-50026637 VE-70000587 VE-30017763 VE-50038905 VE-50038931 VE-50038935 BT-54013-2TK VE-20127776 VE-20127777 VE-20127841 VE-20127894 CARTON BOX CARTON BOX CARTON BOX SNOW BOX ASSY POLY BAG (1250*1000) POLY BAG REMOTE CONTROL UNIT INST BOOK INST BOOK INST BOOK WARRANTY CARD LABEL LABEL LABEL LABEL [A-VERSION] [B-VERSION] [C-VERSION] 4 pcs in 1set (RM-C1100) [A-VERSION] [B-VERSION] [C-VERSION] [A-VERSION] [A-VERSION] [B-VERSION] [C-VERSION]
VICTOR COMPANY OF JAPAN, LIMITED AV & MULTIMEDIA COMPANY VIDEO DISPLAY CATEGORY 12, 3-chome, Moriya-cho, kanagawa-ku, Yokohama, kanagawa-prefecture, 221-8528, Japan

(No.52137)

Printed in Japan WPC

Color profile: Disabled Composite Default screen
ENGLISH FRANAIS NEDERLANDS CASTELLANO DEUTSCH ITALIANO PORTUGUS

AV-28KT1BUF AV-28KT1SUF

COLOUR TELEVISION
TELEVISEUR COULEUR KLEURENTELEVISIE TELEVISOR A COLOR FARBFERNSEHGERT TELEVISORE A COLORI TELEVISOR A CORES

INSTRUCTIONS

MANUEL D'INSTRUCTIONS GEBRUIKSAANWIJZING MANUAL DE INSTRUCCIONES BEDIENUNGSANLEITUNG ISTRUZIONI INSTRUES

50088564

2006 Victor Company of Japan, Limited

0506TKH-VT-VT

D:\IB Guncel\JVC AK49\2835 (AV-28KT1SUF) (1100UK) (4-3) (10041582)\A-COVER PAGE-BG-AK49-C1100UK-2835-CLED-PLLCH-(AV-28KT1SUF)-10041582-50088564.cdr 23 Mays 2006 Sal 11:14:28

Contents

Safety Precautions.. 1 Remote Control.. 2 TV Buttons and Functions and Rear Panel.. 3 Antenna Connections... 3 Preparation... 4 Features... 4 Before Switching on your TV.. 4
Power connection... Connections to the RF input socket.. How to connect other devices... Inserting batteries into the remote control.. 4 4

Safety Precautions

1. Power Source
The receiver should be operated only from a 220-240V AC, 50 Hz. outlet. Ensure you select the correct voltage setting for your convenience.

2. Power Cord

The power supply cord should be placed so that they are not likely to be walked on or pinched by items placed upon them or against them. Pay particular attention to cord where they enter the plug, power outlet, and the point where they exit from the receiver.

3. Moisture and Water

Do not use this equipment in a humid and damp place (avoid the bathroom, the sink in the kitchen, and near the washing machine). Do not expose this equipment to rain or water and do not place objects filled with liquids on it as this may be dangerous.
Switching the TV ON/OFF.. 4
To switch the TV on... 4 To switch the TV off.. 4

Initial Settings... 4

T-V LINK... 5

4. Cleaning

Before cleaning, unplug the receiver from the main supply outlet. Do not use liquid or aerosol cleaners. Use with soft and dry cloth.
Basic Operations... 5 Setting the TV... 6
Picture Menu... Sound Menu.. Feature Menu... Installation Menu... Programme Menu... 9

5. Ventilation

The slots and openings on the receiver are intended for ventilation and to ensure reliable operation. To prevent overheating, these openings must not be blocked or covered in anyway.

Other Features.. 10

Picture Mode... 10 Zoom Modes... 10 VCR Control Buttons... 10

6. Lightning

In case of storm and lightning or when going on holiday, disconnect the power cord from the wall outlet.

7. Replacement Part

When replacement parts are required, be sure the service technician has used replacement parts which are specified by the manufacturer or have the same specifications as the original one. Unauthorized substitutions may result in fire, electrical shock, or other hazards.
Teletext.. 11 Peripheral Equipment Connections.. 12 Tips... 14 Specifications... 14

8. Servicing

Please refer all servicing to qualified personnel. Do not remove cover as this may result in electric shock.

9. Flame sources

Do not place naked flame sources on the apparatus.

10. Stand-By

Do not leave your TV stand-by or operating condition when you leave your house. Warning! Any intervention contrary to regulations, in particular, any modification of high voltage or a replacement of the picture tube may lead to an increased concentration of x-rays. Any television modified in this way no longer complies with license and must not be operated. Instructions for waste disposal: Packaging and packaging aids are recyclable and should principally be recycled. Packaging materials, such as foil bag, must be kept away from children. Batteries, including those which are heavy metal-free, should not be disposed of with household waste. Please dispose of used batteries in an environmentally sound manner. Find out about the legal regulations which apply in your area. -1A01-ENG&BG-AK49-C1100UK-2835-CLED-PLLCH-(AV-28KT1SUF)-10041582-50086735.p22.05.2006, 13:45

Remote Control

= Stand By / Power 0 - 9 = Direct Program STANDARD Button (Picture Mode Change) Colour Buttons RED: Zoom (Picture Size) Change GREEN: Hyper Sound MENU = Menu Button ( ( ) = Cursor Up / Programme Up ) = Cursor Right / Volume +
Teletext Control Buttons VCR Control Buttons ( ( ) = Cursor Down / Programme Down ) = Cursor Left / Volume -
AV = AV Button = Information Button / T-V Link in Program Menu = Mute

CAUTION

RISK OF ELECTRIC SHOCK The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock of persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. -2A01-ENG&BG-AK49-C1100UK-2835-CLED-PLLCH-(AV-28KT1SUF)-10041582-50086735.p22.05.2006, 13:45
TV Buttons and Functions and Rear Panel

$QWHQQD

Antenna Connections

Pq6rh8rpv

WCAhrh

Sq&$uphvhyphiyr

9+)8+)

SrhsUW

WCAVCAhrh

Ayh"uvyrhqphiyr

-3A01-ENG&BG-AK49-C1100UK-2835-CLED-PLLCH-(AV-28KT1SUF)-10041582-50086735.p22.05.2006, 13:45

Preparation

For ventilation, leave a space of at least 10 cm free all around the set. To prevent any fault and unsafe situations, please do not place any objects on top of the set. Use this apparatus in moderate climate.

Features

It is a remote controlled colour television. 100 programmes from VHF, UHF bands or cable channels can be preset. It can tune cable channels. Controlling the TV is very easy by its menu driven system. It has two Euroconnector sockets for external devices (such as computer, video, video games, audio set, etc.) A2+NICAM Stereo sound system. Teletext (Fastext, Toptext). It is possible to connect headphone. Direct channel access. A.P.S. (Automatic Programming System). All programmes can be named. Programme swapping between last watched two programmes. Forward or backward automatic tuning. Sleep timer. Child Lock. Automatic sound mute when no transmission. When no valid signal is detected, after 5 minutes the TV switches itself automatically to stand-by mode. NTSC Playback. S-VHS (via SCART)
NOTE: Remove batteries from remote control when it is not to be used for a long period. Otherwise it can be damaged due to any leakage of batteries.

Switching the TV ON/OFF

To switch the TV on
Your TV will switch on in two steps: 1- Press the power button located on the front of the TV. Then the TV switches itself to standby mode and the power lamp becomes RED located on the lower part of the TV. 2- To switch on the TV from stand-by mode either: Press the , button on the remote control, or, Press a digit button on the remote control so that a programme number is selected, or, Press Programme Up or Down buttons on the TV or on the remote control, so that last switched off programme is selected. The TV will switch on and the power lamp will be GREEN.
Before Switching on your TV

Power connection

IMPORTANT: The TV set is designed to operate on 220-240V AC, 50 Hz. After unpacking, allow the TV set to reach the ambient room temperature before you connect the set to the mains.

To switch the TV off

Press the stand-by button on the remote control, so the TV will switch to stand-by mode and the power lamp will become RED, or, Press the power button located on the front of the TV, so the TV will switch off and the power lamp will turn off.
Connections to the RF input socket
Connect the aerial or cable TV plug to the RF input socket located at the back of the TV and connect the cable plug coming out from the TV out socket located at the devices (VCR, DVB etc.) to this socket as well.

Direct REC:

You can easily record to VCR the images that you are watching on the TV. For details, read the manual for your VCR. Use your VCR controls. VCR IS RECORDING is diplayed. You can not carry out Direct REC using your TVs control. When the VCR is not ready (For example when there is no tape inserted), NO RECORDING is displayed. When you press the following buttons ( D, , AV, MENU, , BACK, SUBTITLE, GUIDE, ZOOM, , / , number buttons) during recording, a message appears asking if you want to stop recording or not. Press or button to stop recording or BLUE button to continue recording. Do not turn the TV off in the following cases: When recording images from an external device connected to TV (For example camcorder). When recording a TV channel after it has been unscrambled on a decoder. When recording a TV channel by using the TVs output because the VCRs own tuner can not properly receive that channel.
After APS is finalized, a programme list will appear on the screen. In the programme list you will see the programme numbers and names assigned to the programmes. If you do not accept the locations and / or the programme names of programmes, you can change them in Program menu. For details see PROGRAMME menu on page 9. If you do not have a T-V LINK compatible VCR, press BLUE button to exit the menu. If you have a T-V LINK compatible VCR connected to the EXT.2 terminal, press button to display T-V LINK menu. Then follow the operating procedure Downloading data to VCR in the following T-V LINK section.

T-V LINK

When a T-V LINK compatible VCR is connected to the EXT.2 terminal on the TV, it is easier to set up the VCR and to view videos. T-V LINK uses the following features:
To use T-V LINK functions
A T-V LINK compatible VCR means a JVC video cassette recorder with the T-V LINK logo, or with one of the following logos. For details see your VCR instruction manual. Q-LINK (A trademark of Panasonic Corporation) Data Logic (A trademark of Metz Corporation) Easy Link (A trademark of Philips Corporation) Megalogic (A trademark of Grundig Corporation) SMARTLINK (A trademark of Sony Corporation)
TV autopower on/VCR image view:
When the VCR starts playing, the TV automatically turns on and images from EXT2 appear on the screen. This function does not happen if your TVs main power is turned off. Set your TVs main power to on (StandBy Mode).

Basic Operations

You can operate your TV using both the remote control and onset buttons.

Downloading data to VCR:

The VCR will automatically download the registered data on the TV channels from the TV. This means you do not need to set up the programme channels on your VCR manually. The T-V LINK menu will be displayed when you press the button while PROGRAM menu is displayed.

Programme Selection (Previous or next programme)
Press Press button to select the previous programme. button to select the next programme.
Programme Selection (direct access):
Press digit buttons on the remote control to select programmes between 0 and 9. TV will switch to the selected programme. To select programmes between 10 - 99, press the digit buttons consecutively which programme you want to select (eg. for programme 27, first press 2 and then 7). When it is late to press second digit button only the first digit programme will be displayed. The limit of the delay time is 3 seconds. Example: PR6 press 6, PR12 press 1 and 2. Press directly the programme number to reselect single digit programmes.

Setting Brightness

As you enter the picture menu, Brightness will be the first selected option. Press Press button to brighten the picture. button to darken the picture.

Setting Contrast

Contrast is the difference and distribution of light and dark tones in an image. Using or button select Contrast. Press button to increase contrast level. Press button to decrease contrast level.

Setting Colour

Using Press or button select Colour. button to increase colour saturation.
-6A01-ENG&BG-AK49-C1100UK-2835-CLED-PLLCH-(AV-28KT1SUF)-10041582-50086735.p22.05.2006, 13:45
Press Using Press Press
button to decrease colour saturation. or button select Sharpness.

Setting Sharpness

button to sharpen the picture. button to soften the picture.
When you watch a picture from your VCR and the picture is unstable, you may improve it by changing the VCR MODE setting from OFF to ON.
Press BLUE button to reset the picture modes to factory default settings.
Setting Hue (In AV mode only)
(During Playback NTSC system, this will appear in AV mode only when NTSC video source is applied. Otherwise, HUE option is invisible in Picture menu.): Using or button select Hue. Press Press button to increase the green tones. button to increase the red tones.

To Store the Settings

In the Picture Menu, all settings are stored automatically.

Sound Menu

Press MENU button, now you are in MENU. In the MENU, select SOUND using or button, then enter the sound menu by pressing or button.
Center value is indicated with two reciprocal arrows.
QD 8UVS@ 8PIUS6TU 8PGPVS TC6 SQI@TT CV@ QD 8UVS@HP9@ 8PGPVSU@HQ WIS W8SHP9@ S@T@U TU6I96 S9 8PPG 6 VUP PAA
TPVI9 WPGVH@ 76G6I8@ TPVI9HP9@ 76TT HPIP

Setting Picture Mode

This item is used to change the picture mode. By pressing or button you may select one of these options: STANDARD, SOFT and BRIGHT. You can also set the Picture Mode by pressing the Blue button directly.

US@7G@

Setting Volume
As you enter the sound menu, Volume will be the first selected option. Press button to increase volume. Press button to decrease volume. Or you can directly change the volume settings using (to decrease) button. (to increase) or +

Setting Colour Temp

This item is used for white colour tint adjustment. By pressing or button you may select one of these options: COOL, NORMAL, WARM.

Setting Balance

It allows adjusting the distribution between the left and right speakers. Using or button select Balance. Press Press button to change balance to the right. button to change balance to the left.
Setting VNR (Video Noise Reduction)
This item is used to reduce the image noise and improve the picture quality at weak signals. Using or button select VNR. Press or button to set VNR level to OFF, MIN, AUTO or MAX. AUTO adjusts the VNR level to OFF, MIN or MAX automatically according to the intensity of the noise.
QD8UVS@ 7SDBCUI@TT 8PIUS6TU 8PGPVS TC6SQI@TT QD8UVS@HP9@ 8PGPVSU@HQ WIS S@T@U TU6I96S9 8PPG PAA
When balance control is in mid position, the cursor is displayed with two reciprocal arrows.

Selecting Sound Mode

Using or button select Sound Mode. Press or button to change Mode. You can select MONO, STEREO, DUAL-I or DUAL-II mode, only if the selected channel supports that mode. In case of bilingual broadcast (Dual Sound), you can select original or dubbed language using mode option.

Setting Bass Level

Using or button select Bass Level. Press button to increase bass level. Press button to decrease bass level. -7-
Setting VCR Mode (In AV mode only)
Using or button select VCR Mode.
A01-ENG&BG-AK49-C1100UK-2835-CLED-PLLCH-(AV-28KT1SUF)-10041582-50086735.p65 7

22.05.2006, 13:45

Setting Treble Level

Using or button select Treble Press button to increase treble level. Press button to decrease treble level

Ext-2 Output

Using or button select Ext-2 Output. Press or button to select the source which will be given. From Ext-2 output, either EXT-1, EXT-3 or TV can be selected.
In the Sound Menu, all settings are stored automatically.

Blue Back

You can set the TV to automatically change to a blue screen if the signal is weak or absent, or when there is no input from an external device. The Blue Background feature can be turned on or off by pressing or button.

Feature Menu

Press MENU button, now you are in MENU. In the MENU, select Feature using or button. Then enter the Feature menu by pressing or button.
A@6UVS@ TG@@QUDH@S 8CDG9GP8F 8PVIUS` G6IBV6B@ @YU!PVUQVU 7GV@768F VF @IBGDTC UW

To Store Settings

In Feature menu all settings are stored automatically.

Installation Menu

Press MENU button, now you are in MENU. In the MENU, select INSTALLATION using or button. Then enter the Installation menu by pressing or button.
3,&785( 6281' )($785( ,167$//$7,21 352*5$00(
DITU6GG6UDPI QSPBS6HH@ 76I9 8C6II@G TU6I96S9 8PGPVST`TU@H 9@8P9@S@YU! ADI@UVIDIB T@6S8C TUPS@ 8 ! 7B Q6G

Sleep Timer

As you enter the Feature menu, Sleep Timer will be the first selected option. Use or button to change the Sleep Timer values between OFF, 10, 20, 30,., 110 and 120. If sleep timer is activated, at the end of the selected time, the TV goes automatically to stand-by mode. You can also set the Sleep Timer by pressing the Yellow button directly.

Child Lock

You can use this feature to prevent children turning the TV on or changing programs or adjustments etc. without remote control. The Child Lock feature can be set by or button to either ON or OFF. When OFF is selected, there will be no difference in the operation of your TV. When ON is selected, the TV can only be controlled by the remote control handset. In this case, the front panel buttons (except the Power On/Off button) will not work. If Child Lock is ON, when one of the front panel buttons (except power button) is pressed, CHILD LOCK OSD is seen on the screen.

Sound Indicator

The alternatives of the indicator are Mono, Stereo, Dual I and Dual II. This indicator is displayed under the programme number indicator on the screen. In Mono broadcast or in forced-mono (for stereo broadcast).

VCR Control Buttons

The buttons can be used to operate a JVC brand VCR. Pressing the button having the same appearance as the original remote control button of a device makes the function work in the same way as the original remote control. Press the VCR Control Button to control your VCR. Note: If your device is not made by JVC, these buttons cannot be used. Even if your device is made by JVC, some of these buttons or any one of the buttons may not work, depending on the device. You can use the / buttons to choose a TV channel which the VCR will receive.

67(5(2

In Stereo broadcast. If dual broadcast detected. Dual I is selected in default and also can be selected after Dual II by Remote Control.

9V6GDD

If Dual II is selected by Remote Control.

Mute Indicator

It is placed in the upper middle of the screen when enabled, and it stays there until it is disabled. To cancel mute, there are two alternatives; the first one is by pressing the button, this volume is set to the preceding - 10 A01-ENG&BG-AK49-C1100UK-2835-CLED-PLLCH-(AV-28KT1SUF)-10041582-50086735.p22.05.2006, 13:45

Teletext

Teletext is an information system that displays text on your TV screen. Using the Teletext information system you can view a page of information on a subject that is available in the list of contents (index). On screen display is not available in text mode. Contrast, brightness or colour control is not available, but volume control is available in text mode.
To Stop Automatic Page Change
The teletext page you have selected may contain more information than what is on the screen; the rest of the information will be displayed after a period of time. Press Press played. button to stop the automatic page change. button again to allow the next page to be dis-

To operate Teletext

Select a TV station on which Teletext is being transmitted. Press (TELETEXT) button. Usually the list of contents (index) is displayed on the screen.

To Select a Subcode Page

Subcode pages are subsections of long Teletext pages that can only be displayed on the screen one section at a time. Select the required Teletext page. Press button. Select the required subcode page number by pressing four digit buttons (e.g. 0001). If the selected subcode page is not displayed in a short time, press button. TV programme will be displayed on the screen. Teletext page number will be displayed on the upper left corner of the screen when the selected page is found. Press button to display the selected Teletext page.

To select a page of Teletext
Press the appropriate digit buttons for the required Teletext page number. The selected page number is displayed at the top left corner of the screen. The Teletext page counter searches until the selected page number is located, so that the desired page is displayed on the screen. Press button to move the Teletext screen forward one page at a time. button to move the Teletext screen backward Press one page at a time.

To exit Teletext

Press button. The screen will switch to TV mode.

Fastext and Toptext

Your TV supports the 7 page Teletext system. When the page number of any of the 7 pages in memory is entered, the system will not search for the requested page; instead it will display the page automatically. button to move the Teletext screen forward one Press page at a time. Press button to move the Teletext screen backward one page at a time. For Fastext and Toptext The subject-heading for the information may have a particular colour. Press an appropriate RED, GREEN, YELLOW or BLUE button in order to reach the relevant page quickly. For TOPTEXT If Toptext transmission is present, colour coded buttons will appear in status row. If Toptext transmission is not present, status row will not appear. In Toptext mode the or commands will request the next or previous page respectively. If Toptext transmission is not available, in case of operation of these commands, wraparound occurs. For example page 100 appears to be one greater than page 199. Toptext has a special page called HITLIST which can be displayed by pressing the button. Use colour buttons on HITLIST page to select a line which will link you to another teletext page.

To Select Index Page

To select the page number of the index (generally page 100), press button.
Searching for a teletext page while watching TV
In the Teletext mode pressing button will switch the screen to the TV mode. In the TV mode enter a page number using digit buttons. As you enter last digit of page number, sign will replace the page number and flash until the entered page number is found. Then the page number will replace sign again. Now you can display this teletext page by pressing button.
To Select Double Height Text
Press button for the top half of the information page to be displayed in double height text. Press button again for the bottom half of the information page to be displayed in double height text. Press text. button once more for the full page of normal height

To Reveal concealed Information
Pressing button once will reveal answers on a quiz or games page. Pressing button again will conceal the revealed answers.
- 11 A01-ENG&BG-AK49-C1100UK-2835-CLED-PLLCH-(AV-28KT1SUF)-10041582-50086735.p22.05.2006, 13:45
Peripheral Equipment Connections
There is a wide range of audio and video equipment that can be connected to your TV. Connection diagrams at the end of this section show you where the different equipment should be connected at the back side of the TV.
Connect a decoder without an aerial socket to the TV
Connect the decoder to your TV with a eurocable (RCA Jack Cable) to EXTERNAL (RCA Jack). When your decoder has a Euroconnector / RCA Jack you can obtain better picture quality if you connect a eurocable (RCA Jack Cable) to EXTERNAL (RCA Jack).

Via the Euroconnector

Your TV set has 2 Euroconnector sockets. If you want to connect peripherals (e.g. video, decoder, etc.) which have Euroconnectors, to your TV, use EXT.1 or EXT.2 input. If an external device is connected via Euroconnector sockets, TV is switched to AV mode automatically. In this case if both sockets are connected, SCART1 has the precedence.
TV and Video Recorder (VCR)
Connect the Video Recorder to the ANT (antenna input) socket of the TV with the aerial cable. Connect the Video Recorder to the EXT.1 or EXT.2 terminal with the SCART cable.

NTSC Playback

Connect a NTSC video recorder to a terminal. Then press AV button to select the corresponding AV mode. NTSC 3.58/4.43 system is detected automatically in AV mode.

T-V LINK compatible VCR

Be sure to connect the T-V LINK compatible VCR to the EXT.2 terminal. If not, the T-V LINK function will not work properly. When connecting a T-V LINK compatible VCR to the EXT.2 terminal, be sure to connect the decoder to the VCR. If not, the T-V LINK function may not work properly. And then set the Decoder(EXT2) (see page 9) function for the channel to ON to unscramble a scrambled channel.

Camera and Camcorder

To connect to the EXT-3 terminal
Connect your camera or camcorder to the right side of your TV. Connect your equipment to the TV via VIDEO (yellow), AUDIO R (red) and AUDIO L (white) inputs. You should connect the jacks to the input in the same colour.

RGB mode

If an equipment can output the RGB signals, connect it to the EXT.1 terminal.

EXT2S Mode

Specifications

Broadcasting System PAL SECAM B/G D/K K I/I L/L Channels and Frequencies Analogue: 46.25 MHz - 862.25 MHz (channel 01-17/21-73) Cable TV: S1 - S41 Sound System A2+Nicam Stereo Power Requirements 220-240 V AC, 50 Hz Power Consumption 105W (Standby < 3W) Picture Tube Size Viewable area 70 cm.(measured diagonally) Audio Output 2x10 W RMS (10% THD) EXT.1 Terminal Euroconnector (21-pin, SCART) * Video Input, Audio L/R Inputs and RGB Inputs are available. * Analogue TV broadcast output (Video and Audio L/R) are available. EXT.2 Terminal Euroconnector (21-pin, SCART) * Video Input, S-VIDEO (Y/C) Input, Audio L/R Inputs are available. * Video and Audio L/R outputs are available. * T-V LINK functions are available. EXT.3 Terminal RCA connectors x 3 * Video Input and Audio Inputs are available. Headphone jack Stereo mini-jack (3.5 mm in diameter) Dimensions (WxHxD) 760 mm x 570 mm x 473 mm Accessories Remote control unit x 1 (RM-C1100) AA/R6 dry cell battery x 2

Can not turn the TV off?

Check that TV/VCR/DVD switch is set to TV position.

Care of the Screen

Clean the screen with a slightly damp, soft cloth. Do not use abrasive solvents as they may damage the TV screen coating layer.
Colours of image on screen are abnormal
Have you selected the correct TV system? Is your TV set or house aerial located too close to the loudspeakers, non-earthed audio equipment or neon lights, etc. ? Mountains or high buildings can cause double pictures or ghost images. Sometimes you can improve the picture quality by changing the direction of the aerial. Is the picture or Teletext unrecognisable? Check if you have entered the correct frequency. The picture quality may degrade when two peripherals are connected to the TV at the same time. In such a case, disconnect one of the peripherals.
No Image on Display Screen
Is the aerial connected properly? Are the plugs connected tightly to the aerial socket? Is the aerial cable damaged? Are suitable plugs used to connect the aerial? If you are in doubt, consult your dealer. No Image means that your TV is not receiving any transmission. Have you pressed the correct buttons on the remote control? Try once more.

You can not hear any sound. Did you perhaps interrupt the sound, pressing button? Are external speakers connected to the TV? Sound is coming from only one of the speakers. Is the balance set to one direction extreme? See Sound menu.
If your TV no longer responds to the remote control, perhaps the batteries are exhausted. Replace the batteries. Have you selected the wrong menu? Press MENU button to return to normal screen.

No solution

If the TV suddenly stops responding, disconnect the power cord of the TV from the AC outlet. Connect it to the AC outlet again to turn on the TV. If the TV returns to a normal state, it is not a failure. If this does not work, switch off, remove the mains plug and call the service personnel; never attempt to repair it yourself.
- 14 A01-ENG&BG-AK49-C1100UK-2835-CLED-PLLCH-(AV-28KT1SUF)-10041582-50086735.p22.05.2006, 13:45