JVC GR-D30us-gr-d30 Manual
JVC GR-D30us-gr-d30 - Instruction Manual, size: 2.8 MB
Here you can find all about JVC GR-D30us-gr-d30 like manual and other informations. For example: review.
JVC GR-D30us-gr-d30 manual (user guide) is ready to download for free.
On the bottom of page users can write a review. If you own a JVC GR-D30us-gr-d30 please write about it to help other people. [ Report abuse or wrong photo | Share your JVC GR-D30us-gr-d30 photo ]
User reviews and opinions
|Bob_G||3:40am on Wednesday, October 13th, 2010|
|Small Size, Great zoom, good picture doesnt work very well at night The size - The picture it can take if you like to adjust this cam can be tricky in the - adjusting area -Sound sucs|
|muck||2:52am on Monday, October 4th, 2010|
|I purchased the gr-d30. After owning it for 3-1/2 months with very little use, the unit refused to operate or eject the tape. do not buy this camera. after around a year of use the camera starts to have an error saying there is too much condensation.|
|vincev||9:44pm on Thursday, August 19th, 2010|
|DO NOT PURCHASE JVC!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! When the camera worked, it was nice. When the camera did not work (a longer period of time).|
|Swannster||11:19am on Thursday, July 29th, 2010|
|I am warning all of you out there who are looking to buy a camera. DO NOT BUY THIS CAMERA!! If you currently own this camera.|
|Cigan||6:53pm on Sunday, July 4th, 2010|
|After a year it quits working because of a condensation error code. $300 down the tubes! Thanks a lot JVC!|
|teacue||4:09am on Friday, May 7th, 2010|
|Condensation lock Had the same problem after approximately four years with the camcorder locking up in a pause mode with "condensation.|
Comments posted on www.ps2netdrivers.net are solely the views and opinions of the people posting them and do not necessarily reflect the views or opinions of us.
This camcorder is designed exclusively for the digital video cassette, SD Memory Card and MultiMediaCard. Only and memory cards* marked or can be used with this unit. cassettes marked Before recording an important scene.. make sure you only use cassettes with the Mini DV mark.. make sure you only use memory cards* with the mark or.. remember that this camcorder is not compatible with other digital video formats.. remember that this camcorder is intended for private consumer use only. Any commercial use without proper permission is prohibited. (Even if you record an event such as a show, performance or exhibition for personal enjoyment, it is strongly recommended that you obtain permission beforehand.)
* Memory cards can be used with GR-D90/D70 only.
AC Adapter AP-V11U or AP-V13U Battery Pack BN-V408U USB Cable (GR-D90/D70 only)
CD-ROM (GR-D90/D70 only)
Lens Cap (See below for attachment)
Audio/Video Cable (3.5 mini-plug to RCA plug)
Lithium Battery* CR2025 (GR-D90/D70 only) (for remote control unit)
(for optional S-Video cable pg. 6 for attachment)
Remote Control Unit* RM-V718U (GR-D90/D70 only)
Pull out by inserting a pointed instrument into the slot. Memory Card 8 MB (GR-D90 only) (Already inserted in the camcorder)
* A battery is pre-installed in the Remote Control Unit a time of shipment (with insulation sheet). To use the Remote Control Unit, remove the insulation sheet.
In order to maintain optimum performance of the camcorder, provided cables may be equipped with one or more core filter. If a cable has only one core filter, the end that is closest to the filter should be connected to the camcorder.
HOW TO ATTACH THE LENS CAP
To protect the lens, attach the provided lens cap to the camcorder as shown in the illustration.
To confirm the lens cap is on correctly make sure the cap is flush to the camera.
1 Make sure the arrow (L) is
5 02.11.6, 3:08 PM
HOW TO ATTACH THE CORE FILTER
Attach the Core Filter(s) (if provided with your model pg. 5) to an optional cable(s). The Core Filter reduces interference.
Release the stoppers on both ends of the Core Filter.
Run the cable through the Core Filter, leaving approx. 3 cm of cable between the cable plug and the Core Filter. Wind the cable once around the outside of the Core Filter as shown in the illustration. Wind the cable so that it is not slack.
Close the Core Filter until it clicks shut.
Take care not to damage the cable. When connecting cables, attach the end with the Core Filter to the camcorder.
Automatic Demonstration takes place when DEMO MODE is set to ON (factory-preset).
1 Separate the Velcro strip. 2 Pass your right hand through the loop and grasp the
3 Adjust your thumb and fingers through the grip, to
easily operate the Recording Start/Stop button w and Power Switch y and Power Zoom Lever &. Be sure to fasten the Velcro strip to your preference.
& y w
DANGER! Do not attempt to take the batteries apart, or expose them to flame or excessive heat, as it may cause a fire or explosion. WARNING! Do not allow the battery or its terminals to come in contact with metals, as this can result in a short circuit and possibly start a fire. The Benefits Of Lithium-Ion Batteries Lithium-ion battery packs are small but have a large power capacity. However, when one is exposed to cold temperatures (below 10C/50F), its usage time becomes shorter and it may cease to function. If this happens, place the battery pack in your pocket or other warm, protected place for a short time, then re-attach it to the camcorder. As long as the battery pack itself is not cold, it should not affect performance. (If youre using a heating pad, make sure the battery pack does not come in direct contact with it.)
1 Set the Power Switch y to
or while pressing down the Lock Button t located on the switch.
2 Pull out the viewfinder fully and adjust it manually for
3 Turn the Diopter Adjustment Control q until the
indications in the viewfinder are clearly focused.
Lithium-ion is vulnerable in colder temperatures.
8 GETTING STARTED
1 GR-D90/70/30US EN 01-02.11.6, 3:09 PM
Shoulder Strap Attachment
Loading/Unloading A Cassette
The camcorder needs to be powered up to load or eject a cassette.
1 Thread the strap through the eyelet e, then fold it
back and thread it through the buckle. Repeat the procedure to attach the other end of the strap to the other eyelet e located under the Grip Strap. Confirm the strap is not twisted.
10 GETTING STARTED
Loading A Memory Card
Picture Quality/Image Size Setting
The provided memory card (GR-D90 only) is already inserted in the camcorder when you receive the camcorder.
The Picture Quality/Image Size can be selected to best match your needs. Refer to the chart on page 18 for your selection.
Button), then open the card cover (MEMORY CARD) p.
1 Make sure the camcorders power is off. 2 Open the LCD monitor ( pg. 47, u Monitor Open 3 Insert the memory card clipped edge first.
1 Set the VIDEO/DSC Switch 4 to DSC, then set
the Power Switch y to while pressing down the Lock Button t located on the switch. The POWER/ CHARGE lamp r lights and the camcorder turns on.
Do not touch the terminal on the reverse side of the label.
(DSC) and press it.
4 To close the card cover p, push it until you hear a
click. To Unload A Memory Card: In step 3 push the memory card, which then comes out of the camcorder automatically. Pull it out and close the card cover p.
QUALITY and press it. The Sub Menu appears. Rotate the MENU/VOLUME wheel % to select the desired mode and press it.
5 Rotate the MENU/VOLUME wheel % to select
IMAGE SIZE and press it. The Sub Menu appears. Rotate the MENU/VOLUME wheel % to select the desired mode and press it.
6 Rotate the MENU/VOLUME wheel % to select
RETURN, and press it twice. The Menu Screen closes.
Label Clipped edge Memory card
Be sure to use only SD Memory Cards marked or MultiMediaCards marked . Some brands of memory cards are not compatible with this camcorder. Before purchasing a memory card , consult its manufacturer or dealer. Before using a new memory card, it is necessary to FORMAT the card. pg. 22.
DSC QUAL I TY F I NE I MAGE S I ZE 4 X8 REC SELECT
Do not insert/remove the memory card while the camcorder is turned on, as this may cause the memory card to be corrupted or cause the camcorder to become unable to recognize whether or not the card is installed.
In the 1024 x 768 mode, images are shot in 720 x 480 pixels and they are converted and stored in the 1024 x 768 file size.
During Shuttle Search, parts of the picture may not be clearly visible, particularly on the left side of the screen.
12 : 34 : 24
Frames are not displayed during recording.
RECORDING FROM THE MIDDLE OF A TAPE
Play back a tape or use Blank Search ( pg. 15) to find the spot at which you want to start recording, then engage the Still Playback mode ( pg. 14, Normal Playback).
or while pressing down the Lock Button t located on the switch, then start recording.
The time code cannot be reset. During fast-forwarding and rewinding, the time code indication does not move smoothly. The time code is displayed only when TIME CODE is set to ON ( pg. 31).
14 TAPE RECORDING
Helps you find where you should start recording in the middle of a tape to avoid time code interruption ( pg. 14).
D70 only), then set the Power Switch y to PLAY while pressing down the Lock Button t located on the switch.
1 Load a tape ( pg. 9). 2 Set the VIDEO/DSC Switch 4 to VIDEO (GR-D90/ 3 Press BLANK SEARCH *.
BLANK SEARCH Q appears and the camcorder automatically starts reverse or forward shuttle search, then stops at the spot which is about 3 seconds of tape before the beginning of the detected blank portion. To cancel Blank Search midway.. press 5 5.
If Stop mode continues for 5 minutes when power is supplied from a battery, the camcorder shuts off automatically. To turn on again, set the Power Switch y to OFF (CHARGE), then to PLAY. The playback picture can be viewed in the LCD monitor, viewfinder or on a connected TV ( pg. 16). You can also view the playback picture on the LCD monitor with it flipped over and pushed against the camera body. LCD monitor/viewfinder indications: When power is supplied from a battery: the battery pack remaining power indicator is displayed. When power is supplied from an AC outlet: does not appear. During Stop mode, none of the indications are displayed. When a cable is connected to the AV connector, the sound is not heard from the speaker. If still playback continues for more than about 3 minutes, the camcorders Stop mode is automatically engaged. When 4/is pressed to engage still playback, the image may not pause immediately while the camcorder stabilizes the still image.
In step 3, if the current position is at a blank portion the camcorder searches in the reverse direction, and if the current position is at a recorded portion the camcorder searches in the forward direction. Blank Search does not work if HEAD CLEANING REQUIRED. USE CLEANING CASSETTE has appeared with the tape. If the beginning or end of the tape is reached during Blank Search, the camcorder stops automatically. A blank portion which is shorter than 5 seconds of tape may not be detected. The detected blank portion may be located between recorded scenes. Before you start recording, make sure there is no recorded scene after the blank portion.
To Protect Valuable Files (available only for SD Memory Card).
Write/erase protection tab
.. slide the write/erase protection tab on the side of the memory card in the direction of LOCK. This prevents the memory card from being recorded over. To record on this memory card, slide the tab back to the position opposite to LOCK before loading it.
MEMORY CARD RECORDING EN
1 GR-D90/70/30US EN 17-22
02.11.6, 3:11 PM
Approximate Number of Storable Images
Image Size/ Picture Quality 1024 x 768/ FINE 1024 x 768/ STANDARD 640 x 480/ FINE 640 x 480/ STANDARD SD Memory Card (optional) 8MB 16MB 32MB 64MB 405 1215
1 Load a memory card ( pg. 11). 2 Set the VIDEO/DSC Switch 4 to DSC, then set
A stored image is displayed.
the Power Switch y to PLAY while pressing down the Lock Button t.
3 Press to display the next image, or press 2
6 to display the previous image.
To Magnify The Stored Images Press the Zoom Button T ; on the remote control to zoom in (up to 44X), or W A to zoom out. You can also magnify a particular part of an image ( pg. 35). By pressing 4/6 7, 3 8, 2 6, INDEX !, INFO 0 magnification returns to normal instantly.
Image Size/ Picture Quality 1024 x 768/ FINE 1024 x 768/ STANDARD 640 x 480/ FINE 640 x 480/ STANDARD
8MB* 16MB** 32MB** 215 645
1. Make sure the VIDEO/DSC Switch 4 is set to DSC and the Power Switch y is set to , then press the MENU/VOLUME wheel %. 2. Perform steps 3 and 4 of To Adjust The Brightness Of The Display on page 12.
Pressing INFO 0 gives you details on the displayed file ( pg. 19, Viewing File Information). You can also overview several files at a time ( pg. 19, Index Playback). You can turn off the on-screen playback display ( pg. 19, Removing On-Screen Display). Images shot in a file size that is not compatible with this camcorder will be displayed as reduced-size thumbnail images. These thumbnail images cannot be transferred to a PC. Images shot with devices (such as JVC GR-DVM70) that are not compatible with DCF cannot be viewed with this camcorder; UNSUPPORTED FILE! will be displayed.
* Provided with GR-D90 only ** Optional
The number of storable images depends on the selected picture quality as well as the composition of the subjects in the images and the type of memory card being used.
[For Normal Playback] To display the next image To display the previous image
Making A New Folder
New still pictures you are going to take can be separated from previously shot pictures by resetting the file name to DVC00001; these new pictures will be stored in a new folder. Set the VIDEO/DSC Switch 4 to DSC, then set the Power Switch y to PLAY while pressing down the Lock Button t located on the switch. A stored file is displayed. Screen appears. Rotate the MENU/VOLUME wheel % to select NO. RESET, then press it. The NO. RESET Screen appears. Rotate the MENU/VOLUME wheel % to select EXECUTE, then press it. The new folder (such as 101JVCGR) will be made and the file name of the next shot starts from DVC00001.
2 Press the MENU/VOLUME wheel % in. The Menu 3
22 (GR-D90 and GR-D70 only)
Makes dark subjects or areas even brighter than they would be under good natural lighting. Although the recorded image is not grainy, it may look as if it is strobing due to the slow shutter speed.
Program AE with special effects can be changed during recording or during Record-Standby. Some modes of Program AE special effects cannot be used during Night-Alive.
while pressing down the Lock Button t located on the switch. Open the LCD monitor fully or pull out the viewfinder fully.
1/60: The shutter speed is fixed at 1/60th of a second. Black bands that usually appear when shooting a TV screen become narrower. 1/100: The shutter speed is fixed at 1/100th of a second. The flickering that occurs when shooting under a fluorescent light or mercury-vapor lamp is reduced.
2 Press NIGHT 0 so that the Night-Alive indicator
The shutter speed is automatically adjusted to provide up to 30 times sensitivity. * while the shutter speed is A appears beside being automatically adjusted. To Deactivate Night-Alive.. press NIGHT 0 again so that the Night-Alive indicator disappears.
During Night-Alive, the following functions or settings cannot be activated and its indicator blinks or goes out: Some modes of Program AE With Special Effects ( pg. 23, 24). GAIN UP in the CAMERA Menu ( pg. 29). DIS in the MANUAL Menu ( pg. 29). During Night-Alive, it may be difficult to bring the camcorder into focus. To prevent this, use of manual focus and/or a tripod is recommended.
Fade in or out with a white screen.
Fade in or out with a black screen.
Fade in to a color screen from a black and white screen, or fade out from color to black and white.
Wipe in on a black screen from the upper right to the lower left corner, or wipe out from lower left to upper right, leaving a black screen.
The scene starts in the center of a black screen and wipes in toward the corners, or comes in from the corners, gradually wiping out to the center.
WIPE/FADER, then press it.
desired function, then press it. Selection is complete. Press the MENU/VOLUME wheel % in again. The WIPE/FADER Menu disappears and the effect is reserved. The indicator representing the selected effect appears.
Wipe in from right to left, or wipe out from left to right.
Wipe in as the two halves of a black screen open to the left and right, revealing the scene, or wipe out and the black screen reappears from left and right to cover the scene.
5 Press the Recording Start/Stop Button w to activate
the Fade-in/out or Wipe-in/out. To Deactivate The Selected Effect.. select OFF in step 4.
The scene wipes in from the bottom to the top of a black screen, or wipes out from top to bottom, leaving a black screen.
Some Fade/Wipe Effects cannot be used with certain modes of Program AE with special effects ( pg. 23). If an unusable Fade/Wipe Effect is selected, its indicator blinks or goes out.
Wipe in from the center of a black screen toward the top and bottom, or wipe out from the top and bottom toward the center leaving a black screen.
You can extend the length of a Fade or Wipe by pressing and holding the Recording Start/Stop Button w.
24 FOR RECORDING
1 GR-D90/70/30US EN 23-02.11.6, 3:12 PM
Snapshot (For Tape Recording)
This feature lets you record still images that look like photographs onto a tape.
SNAPSHOT MODE SELECTION
1 Set the VIDEO/DSC Switch 4 to VIDEO (GR-D90/
D70 only), then set the Power Switch y to while pressing down the Lock Button t located on the switch. Open the LCD monitor fully or pull out the viewfinder fully.
(CAMERA), then press it.
SNAP MODE, then press it.
5 Rotate the MENU/VOLUME wheel % to select the
desired Snapshot mode, then press it. Rotate the MENU/VOLUME wheel % to select RETURN and press it twice. The Menu Screen closes.
To remove the shutter sound, BEEP on pg. 30. If Snapshot recording is not possible, PHOTO y blinks when SNAPSHOT ^ is pressed. If Program AE with special effects ( pg. 23) is engaged, certain modes of Program AE with special effects are disabled during Snapshot recording. In such a case, the icon blinks. If SNAPSHOT ^ is pressed when DIS is set to ON ( pg. 29), the Stabilizer will be disabled. The Motor Drive mode is disabled when REC SELECT is set to / in the Menu Screen ( pg. 31). / in the DSC If REC SELECT is set to Menu Screen, still images are recorded on the memory card as well (640 x 480 pixels). During tape playback as well, all snapshot modes are available when COPY is set to OFF in the Menu Screen ( pg. 31). However, the shutter sound is not heard. During Snapshot recording, the image displayed in the viewfinder may be partially missing. However, there is no effect in the recorded image. When a cable is connected to the AV connector, the shutter sound is not heard from the speaker, however it is recorded onto the tape.
The camcorders Full Range AF system offers continuous shooting ability from close-up (as close as approx. 5 cm (2") to the subject) to infinity.
FULL Snapshot mode with no frame PIN-UP Pin-Up mode FRAME Snapshot mode with frame
However, correct focus may not be obtainable in the situations listed below (in these cases use manual focusing): When two subjects overlap in the same scene. When illumination is low.* When the subject has no contrast (difference in brightness and darkness), such as a flat, one-color wall, or a clear, blue sky.* When a dark object is barely visible in the viewfinder.* When the scene contains minute patterns or identical patterns that are regularly repeated. When the scene is affected by sunbeams or light reflecting off the surface of a body of water. When shooting a scene with a high-contrast background.
* The following low-contrast warnings appear blinking: , , and
There is the sound effect of a shutter closing.
1 Press SNAPSHOT ^. PHOTO y appears while
the snapshot is being taken. If you press during Record-Standby.. PHOTO y appears and a still image will be recorded for approx. 6 seconds, then the camcorder re-enters the Record-Standby mode. If you press during Recording.. PHOTO y appears and a still image will be recorded for approx. 6 seconds, then the normal recording resumes. Regardless of the Power Switch y position ( or ), Snapshot recording takes place using the selected Snapshot mode. Motor Drive Mode Keeping SNAPSHOT ^ pressed provides an effect similar to serial photography. (Interval between still images: approx. 1 second)
Adjust zoom or position yourself so that the white paper fills the screen.
3 Press the MENU/VOLUME wheel % in until
begins blinking rapidly. When the setting is completed, blinking. resumes normal
4 Press the MENU/VOLUME wheel % in twice. The
White Balance Adjustment
A term that refers to the correctness of color reproduction under various lighting. If the white balance is correct, all other colors will be accurately reproduced. The white balance is usually adjusted automatically. However, more advanced camcorder operators control this function manually to achieve a more professional color/tint reproduction. Menu Screen closes and the Manual White Balance indicator ( is displayed.
In step 2, it may be difficult to focus on the white paper. In such a case, adjust focus manually ( pg. 26). A subject can be shot under various types of lighting conditions indoors (natural, flourescent, candlelight, etc.). Because the color temperature is different depending on the light source, the subject tint will differ depending on the white balance settings. Use this function for a more natural result. Once you adjust white balance manually, the setting is retained even if the power is turned off or the battery removed.
For Recording Menu
This camcorder is equipped with an easy-to-use, on-screen menu system that simplifies many of the more detailed camcorder settings ( pg. 28 31). Set the Power Switch y to while pressing down the Lock Button t located on the switch. Open the LCD monitor fully or pull out the viewfinder fully.
Refer to Fade/Wipe Effects ( pg. 24).
Refer to Program AE With Special Effects ( pg. 23).
Refer to Exposure Control and Iris Lock ( pg. 26, 27).
3 Rotate the MENU/VOLUME wheel % to select the
desired function menu, and press it.
Refer to White Balance Adjustment and Manual White Balance Operation ( pg. 27).
4 Function menu setting depends on the function.
If you have selected WIPE/FADER, PROGRAM AE, EXPOSURE or W. BALANCE.. see the column on the right. If you have selected CAMERA, MANUAL, SYSTEM, CAMERA DISPLAY or DSC.. go to step 5.
Settings made in the CAMERA Menu remain effective whether the Power Switch y is set to or . However, the menu settings can be changed only when the Power Switch y is set to .
CAMERA R EC MODE SOUND MODE 12B I T 40X Z OOM S NAP MODE FUL L AGC GA I N UP
desired function and press it. The Sub Menu appears. Then, rotate the MENU/VOLUME wheel % to select the parameter, and press it. Selection is complete. Rotate the MENU/VOLUME wheel % to select RETURN and press it twice. The Menu Screen closes. The icon represents END.
Allows you to set the tape recording mode ([SP] or LP) depending on your preference ( pg. 10).
When the Menu Screen is left on for a couple of minutes, a residual image may be left on the screen and it may take several seconds for the residual image to disappear. This is not due to any defect of the unit.
SOUND MODE [12BIT]: Enables tape recording of stereo sound on four separate channels, and is recommended for use when performing audio dubbing. (Equivalent to the 32 kHz mode of previous models) 16BIT: Enables tape recording of stereo sound on two separate channels. (Equivalent to the 48 kHz mode of previous models) ZOOM 16X: When set to 16X while using digital zoom, the zoom magnification will reset to 16X since digital zoom will be disengaged. [40X]: Allows you to use the Digital Zoom. By digitally processing and magnifying images, zooming is possible from 16X (the optical zoom limit), to a maximum of 40X digital magnification. 700X: Allows you to use the Digital Zoom. By digitally processing and magnifying images, zooming is possible from 16X (the optical zoom limit), to a maximum of 700X digital magnification. SNAP MODE Refer to Snapshot (For Tape Recording) ( pg. 25).
[ ] = Factory-preset
28 USING MENUS FOR DETAILED ADJUSTMENT
1 GR-D90/70/30US EN 23-02.11.6, 3:13 PM
GAIN UP OFF: Allows you to shoot dark scenes with no picture brightness adjustment. [AGC]: The overall appearance may be grainy, but the image is bright. : The shutter speed is automatically AUTO adjusted (1/30 1/200 sec.). Shooting a subject in low or poor lighting at 1/30 sec. shutter speed provides a brighter image than in the AGC mode, but the subjects movements are not smooth or natural. The overall appearance may be grainy. While the shutter speed is being automatically adjusted, is displayed.
The MANUAL settings are effective only when the Power Switch y is set to .
MANUAL ON DIS T ELE MACRO OF F W I DE MODE OF F W I ND CUT OF F
WIDE MODE [OFF]: Records with no change in the screen ratio. For playback on a TV with a normal screen ratio. CINEMA : Inserts black bands at the top and bottom of the screen. During playback on wide-screen TVs, the black bands at the top and bottom of the screen are cut and the screen ratio 2 appears. When using this becomes 16:9. mode, refer to your wide-screen TVs instruction manual. During playback/recording on 4:3 TVs/LCD monitor/viewfinder, black bands are inserted at the top and bottom of the screen and the image appears like a letterboxed 16:9 movie. The CINEMA mode is effective only when the VIDEO/DSC Switch 4 is set to VIDEO (GR-D90/ D70 only). SQUEEZE : For playback on TVs with an aspect ratio of 16:9. Naturally expands the image to fit the screen without distortion. 2 appears. When using this mode, refer to your wide-screen TVs instruction manual. During playback/recording on 4:3 TVs/LCD monitor/viewfinder, the image is elongated vertically. The SQUEEZE mode is effective only when the VIDEO/DSC Switch 4 is set to VIDEO (GR-D90/ D70 only). WIND CUT [OFF]: Disengages the function which cuts down on noise created by wind. ON : Helps cut down on noise created by wind. 7 appears. The quality of the sound will change. This is normal.
The audio track can be customized only when recorded in the 12-bit mode ( pg. 28).
You can record a new scene into a previously recorded tape, replacing a section of the original recording with minimal picture distortion at the in and outpoints. The original audio remains unchanged.
Audio Dubbing is not possible on a tape recorded in 16-bit audio, on a tape recorded in the LP mode or on a blank portion of a tape. To perform Audio Dubbing while watching on the television, make connections ( pg. 16).
Before performing the following steps, make sure that TIME CODE is set to ON in the Menu Screen ( pg. 31, 32). Insert Editing is not possible on a tape recorded in the LP mode or on a blank portion of a tape. To perform Insert Editing while watching in the television, make connections ( pg. 16).
Play back the tape to locate the point where editing will start, then press PAUSE (6) Y.
2 While holding A.DUB (e) k on the remote control, 3 Press PLAY (4) j, then begin narrating.
Speak into the microphone. To pause dubbing, press PAUSE (6) Y.
press PAUSE (6) Y. 6e E and MIC (GR-D90/D70 only) appear.
1 Play back the tape, locate the Edit-Out point and
press PAUSE (6) Y. Confirm the time code at this point ( pg. 31, 32).
2 Press REW (2) I until the Edit-In point is located,
then press PAUSE (6) Y.
4 To end Audio Dubbing, press PAUSE (6) Y, then
STOP (5) P. To hear the dubbed sound during playback.. set 12BIT MODE to SOUND 2 or MIX in the Menu Screen ( pg. 32).
3 Press and hold INSERT (w) O on the remote 4 Press START/STOP s to begin editing.
control, then press PAUSE (6) Y. 6w 8 and the Time Code (min.:sec.) appear and the camcorder enters Insert-Pause mode. Confirm the insert at the time code you checked in step 1. To pause editing, press START/STOP s. Press it again to resume editing.
Sound is not heard from the speaker during Audio Dubbing. When editing onto a tape that was recorded at 12-bit, the old and new soundtracks are recorded separately. If you dub onto a blank space on the tape, the sound may be disrupted. Make sure you only edit recorded areas. If feedback or howling occurs during TV playback, move the camcorders microphone away from the TV, or turn down the TVs volume. If you change from 12-bit to 16-bit in mid-recording and then use the tape for Audio Dubbing, it is not effective from the point where 16-bit recording began. During Audio Dubbing, when the tape moves to scenes recorded in the LP mode, scenes recorded in 16-bit audio or a blank portion, Audio Dubbing stops ( pg. 50). To perform Audio Dubbing with a video unit connected to the camcorders AV connector, first set S/AV INPUT to ON in the Menu Screen ( pg. 31). AUX appears instead of MIC.
To USB connector
To DV connector
PC with DV connector
Before consulting your JVC dealer, please check the following to see if you can correct the problem yourself. The camcorder is a microcomputer-controlled device. External noise and interference (from a TV, a radio, etc.) might prevent it from functioning properly. In such cases, first disconnect its power supply unit (battery pack, AC Adapter, etc.) and wait a few minutes; and then re-connect it and proceed as usual from the beginning.
The focus does not adjust automatically.
Focus is set to the Manual mode. Set Focus to the Auto mode ( pg. 26). The recording was done in a dark place, or the contrast was low. The lens is dirty or covered with condensation. Clean the lens and check the focus again ( pg. 43).
The cassette will not load properly.
The cassette is in the wrong position. Set it in the right position ( pg. 9). The batterys charge is low. Install a fully charged battery ( pg. 7, 8).
No power is supplied.
The power is not connected properly. Connect the AC Adapter securely ( pg. 7). The battery is dead. Replace the dead battery with a fully charged one ( pg. 7, 8).
The memory card will not load properly.
The memory card is in the wrong position. Set it in the right position ( pg. 11).
SET DATE/TIME! appears.
The date/time is not set. Set the date/time ( pg. 10). The built-in clock battery has run out and the previously set date/time has been erased. Consult your nearest JVC dealer for replacement.
Snapshot mode cannot be used.
The Squeeze mode is selected. Disengage the Squeeze mode ( pg. 29).
The color of Snapshot looks strange.
The light source or the subject does not include white. Or there are various different light sources behind the subject. Find a white subject and compose your shot so that it also appears in the frame ( pg. 17, 25). The Sepia or Monotone mode is activated. Turn off Sepia and Monotone ( pg. 23).
Recording cannot be performed.
For Tape Recording The tapes erase protection tab is set to SAVE. Set the tapes erase protection tab to REC ( pg. 9). The Power Switch y is set to PLAY or OFF (CHARGE). Set the Power Switch y to or ( pg. 13). The VIDEO/DSC Switch 4 is set to DSC. Set the VIDEO/DSC Switch 4 to VIDEO. TAPE END appears. Replace with new cassette ( pg. 9). The cassette holder cover is open. Close the cassette holder cover. For Memory Card Recording The VIDEO/DSC Switch 4 is set to VIDEO. Set the VIDEO/DSC Switch 4 to DSC.
Wellgate 26XX RL41ptih Draft HT502PH FX-82LB U8380 LE32B460b2W RTH7400D UX-D26CW Dvdr3300H-05 TDM-7582R PSC 2115 Preamp XG-P10XE MZ-R91 Photo Motorola W755 YP-C1X PDS4221 Motorola W230 Recorder RH397D GA-P55a-ud4 R-390L MS18AH Player Deskpro EN DVP3350V 02 Blackberry 6710 BS-12500 UC4030A Kenwood MA-5 V3000 DSC-W360 HT-THQ22 42PFL9632D-10 Toshiba E330 S2 ABS Isdn 951 Netbook RR-US006 IP35-E Deskjet 3744 MP-42PX10 35-19 S 4WD F300 Lawn BOY S7010 TX-14P1 Treadmills EMX-120RDS STR-DE400 G2400W LX-M140A Crusader MFC-3820CN ICD-SX45 BMW 325D VF-30NKB Chartplotter DH404E GPS II DIR-655 Bose 301V GT 2002 SGH-B130L 200 B200 RS26ddapn CTK-811EX SS-400B Microtower PC SA-XR70 HK32V001 CX-designer KT-DB1000 Power Pc Card Bass500 Mixer 32PW6006 FW360C ZK25 10R IC-M88 T8500 ICF-C153 Whitetail II Rev 1 HD 2 KF6000 TUE-T152 Blade Review DEH-P5950IB 300-52 CM-2600D Avantgarde U6485200B GKC1817 Yamaha DTR2 HI-605 MX-GT91R
manuel d'instructions, Guide de l'utilisateur | Manual de instrucciones, Instrucciones de uso | Bedienungsanleitung, Bedienungsanleitung | Manual de Instruções, guia do usuário | инструкция | návod na použitie, Užívateľská príručka, návod k použití | bruksanvisningen | instrukcja, podręcznik użytkownika | kullanım kılavuzu, Kullanım | kézikönyv, használati útmutató | manuale di istruzioni, istruzioni d'uso | handleiding, gebruikershandleiding
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101