HA-W500RF (EK)

10/25/2002

Page B

CORDLESS FM STEREO HEADPHONES

INSTRUCTIONS

2002 VICTOR COMPANY OF JAPAN, LIMITED Printed in China J5500-115A J5500-115A

Page D

SOME DOS AND DONTS ON THE SAFE USE OF EQUIPMENT This equipment has been designed and manufactured to meet international safety standards but, like any electrical apparatus, care must be taken if you are to obtain the best results and safety is to be assured. Do Do read the operating instructions before you attempt to use the equipment. ensure that all electrical connections (including the plug, extension cord and interconnections between pieces of equipment) are properly made and in accordance with the manufacturers instructions. Switch off and withdraw the plug when making or changing connections. consult your dealer if you are ever in doubt about the installation or operation or safety of your equipment. be careful with glass panels or doors on equipment. DONT DONT DONT continue to operate the equipment if you are in any doubt about it working normally, or if it is damaged in any wayswitch offwithdraw the plug and consult your dealer. remove any fixed cover as this may expose dangerous voltages. leave equipment switched on when it is unattended unless it is specifically stated that it is designed for unattended operation or has a standby mode. Switch off using the switch on the equipment and make sure that your family know how to do this. Special arrangements may need to be made for infirm or handicapped people. DONT DONT DONT use equipment such as personal stereos or radios so that you are distracted from the requirements of road safety. It is illegal to watch television when driving. listen to headphones at high volume as such use can permanently damage your hearing. obstruct the ventilation of the equipment, for example with curtains or on soft furnishings. Overheating will cause damage and shorten the life of the equipment. DONT use makeshift stands and NEVER fix legs with wood screws. To ensure complete safety always fit the manufacturers approved stand or legs with the fixing screws supplied according to the instructions. allow electrical equipment to be exposed to rain or moisture. NEVER let anyone especially children push anything into holes, slots or any other opening in the case. This could result in a fatal electrical shock. NEVER guess or make changes with electrical equipment of any kind. It is better to be safe than sorry! Italian Danish German Swedish French Finnish Dutch
OPERATING AT 863 MHz TO 865 MHz ACCORDING TO THE USED FREQUENCY BAND THIS DEVICE IS INTENDED TO USE IN GERMANY, THE UK, FRANCE, AUSTRIA, THE NETHERLANDS, SWEDEN, NORWAY, DENMARK, FINLAND, BELGIUM

English

Hereby, JVC, declares that this HA-W500RF is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. JVC vakuuttaa tten ett HA-W500RF tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sit koskevien direktiivin muiden ehtojen mukainen. Hierbij verklaart JVC dat het toestel HA-W500RF in overeenstemming is met de essentile eisen en de andere relevante bepalingen van richtlijn 1999/5/EG Bij deze verklaart JVC dat deze HA-W500RF voldoet aan de essentile eisen en aan de overige relevante bepalingen van Richtlijn 1999/5/EC. Par la prsente JVC dclare que lappareil HA-W500RF est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE Par la prsente, JVC dclare que ce HA-W500RF est conforme aux exigences essentielles et aux autres dispositions de la directive 1999/5/CE qui lui sont applicables. Hrmed intygar JVC att denna HA-W500RF str i verensstmmelse med de vsentliga egenskapskrav och vriga relevanta bestmmelser som framgr av direktiv 1999/5/EG. Undertegnede JVC erklrer herved, at flgende udstyr HA-W500RF overholder de vsentlige krav og vrige relevante krav i direktiv 1999/5/EF Hiermit erklrt JVC, dass sich dieser/diese/dieses HA-W500RF in bereinstimmung mit den grundlegenden Anforderungen und den anderen relevanten Vorschriften der Richtlinie 1999/5/EG befindet. (BMWi) Hiermit erklrt JVC die bereinstimmung des Gertes HA-W500RF mit den grundlegenden Anforderungen und den anderen relevanten Festlegungen der Richtlinie 1999/5/EG. (Wien)

ABOVE ALL Greek

JVC HA-W500RF 1999/5/EK Con la presente JVC dichiara che questo HA-W500RF e conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE. Por medio de la presente JVC declara que el HA-W500RF cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directive 1999/5/CE JVC declara que este HA-W500RF est conforme com os requisitos essenciais e outras disposies da Directiva 1999/5/CE.

CAUTION:

CHARGE ONLY WITH PROVIDED NICKEL-CADMIUM TYPE BATTERIES. OTHER TYPES OF BATTERIES MAY BURST CAUSING PERSONAL INJURY AND DAMAGE.

Spanish Portuguese

Page 4
Thank you for purchasing this JVC product. Before you begin operating this unit, please read the instructions carefully to be sure you get the best possible performance. If you have any questions, consult your JVC dealer.
NAMES OF PARTS AND THEIR FUNCTIONS

Transmitter

CAUTION
To reduce the risk of electrical shocks, fire, etc.: 1. Do not remove screws, cover or cabinet. 2. Do not expose this appliance to rain or moisture. 3

IMPORTANT

1. Installation q Select a place which is level, dry and neither too hot nor too cold (between 0C and 35C /32F and 95F). q Keep away from direct sunlight. q Do not put it too close to a heater. 2. Power cord q Do not handle the power cord with wet hands! q Do not bend the power cord sharply. 3. Malfunctions, etc. q There are no serviceable parts inside. If anything goes wrong, unplug the power cord and consult your dealer. q Do not insert any metallic object. q Do not allow water to get inside.

FEATURES

Frequency modulation system which allows headphones to be used even in areas where the transmitter cannot be seen q Reception range (up to 100 m (328 ft): using JVC measurement system) q Rechargeable system with built-in Ni-Cd batteries provided q Large 40 mm dia. drivers for highquality sound q Automatic Power On/Off transmitter q Auto-level control circuit that automatically adjusts signals to the appropriate modulation level q Single volume control adjusts the volume level of the left and right channels simultaneously q Adaptable to any audio/visual equipment
1 Power Indicator When an audio signal is input: The power automatically turns on and the indicator lights in green. 2 CHANNEL Adjusts the transmission frequency. 3 Antenna For use, pull out and stand it vertically. 4 Audio input cord and plug 1.5 m cord and 3.5 mm dia. stereo miniplug. 5 DC IN (DC 9V Jack) Connect plug 7 (DC Out for Transmitter) on the AC adaptor.
6 AC adaptor (J47127-001) Connects to a household AC outlet (AC 230 V, 50 Hz). Note: The provided AC adaptor is exclusively for use with this unit. Do not connect to any other equipment. 7 DC Out (for Transmitter) 8 DC Out (for Receiver Charging)

Page 6

Receiver (Cordless Headphones)

CONNECTION

s How to connect to AV equipment
Connection to HEADPHONES jack
When connecting to a standard stereo phone jack (6.3 mm dia.) Use the provided plug adaptor (Converts a stereo miniplug to a standard stereo phone plug)
To HEADPHONES jack TV, audio amplifier, VCR, tape deck, video disc player, etc.
When connecting to a stereo minijack
When connecting to a monaural minijack Use an optional plug adaptor (Converts a stereo miniplug to a monaural miniplug)
1 POWER (Power switch) 2 Power Indicator The indicator lights in red when the power is turned on. Also, the indicator lights in green during recharge. 3 CHARGE (Charging input terminal) 4 VOL. (Volume control) Adjusts the volume level of the left and right channels simultaneously.
5 TUNING (Tuning control) Adjusts the reception frequency. 6 Soft Comfort-Fit Headband
Connection to LINE OUT or REC OUT terminals
For replacement ear pads, please consult with the dealer where you purchased the headphones.
To LINE OUT or REC OUT terminals TV, audio amplifier, VCR, tape deck, video disc player, etc.

R-channel (red plug)

Provided connection cord

L-channel (white plug)

Page 8
Connection to power supply
To AC outlet (AC 230 V, 50 Hz)
POWER REQUIREMENTS OF HEADPHONES
Charging rechargeable Ni-Cd batteries

Plug polarities

Provided exclusive AC adaptor (J47127-001)
3.5 mm plug To DC 9 V jack

To AC outlet

2.5 mm plug
Note: Be sure to use the provided exclusive AC adaptor (J47127-001) for connection. Use of any other AC adaptor may cause a malfunction.
2.5 mm plug To receiver CHARGE jack
3,5 mm plug To DC 9 V jack

To receiver CHARGE jack

RANGE OF USE
The usable area between the transmitter and the headphones is within a radius of max 100 m (based on measurements taken when placed in direct view in a straight line and no interference situation).
1 Set the POWER switch on the headphones to OFF. The batteries cannot be charged when the switch is set to ON. 2 Connect the DC out (for Receiver Charging) from the AC adaptor to the headphones. 3 Plug the AC adaptor into an AC outlet. The charger starts charging the batteries automatically.
Max: 100 m (Under controlled ambient conditions)

Charging time

The battery can be fully charged in approx. 24 hours. During recharge the indicator lights in green, which will start to blink rapidly near completion. Blinking will gradually slow down or turn off at completion. When done, unplug the DC plug from the battery.

Note: The usable area may differ depending on building structure, etc. The range becomes shorter in the following cases:
Be sure to keep this unit more than 0.5 m/1.64 ft away from concrete walls, metal furniture, etc.

Battery running time

After charging is complete, you can use them continuously for approx. 20 hours. Tips for better use q Be sure to charge the batteries within the temperature range of 10C ~ 35C (50F ~ 95F). q Charging batteries that are not completely exhausted will cause efficiency to decline. Be sure to charge them after they have been completely exhausted.
In places such as inside an apartment with reinforced concrete walls, or when the transmitter and headphones are separated by obstacles such as steelreinforced doors.
When items such as metal furniture are situated nearby.

Page 10

CAUTIONS ABOUT THE RECHARGEABLE BATTERY
ATTENTION: The product that you have purchased contains a rechargeable battery. The battery is recyclable. At the end of its useful life, under various state and local laws, it may be illegal to dispose of this battery into the municipal waste stream. Check with your local solid waste officials for details in your area for recycling options or proper disposal.

CAUTIONS ABOUT CHARGING

1. Be sure to use only this unit for charging. 2. You can charge the rechargeable Ni-Cd batteries approx. 300 times. 3. Charging times differ depending on the temperature range or the amount of charge already in the batteries. 4. Excessive charging doesnt result in malfunction. 5. Battery life will decrease in cold places. 6. If the usable time of fully-charged batteries decreasses by about half, replace them with new ones. When purchasing rechargeable Ni-Cd batteries, consult the dealer from whom you bought this product. Exclusive Rechargeable Ni-Cd Batteries: J46514 (1.2 V, 600 mAh, 2 pcs/pack) 7. Due to characteristics of the batteries, they expend their charge a little even when the power is turned off. 8. Be sure to use the provided AC adaptor (model J47127-001)
Note: Be sure to consult your local dealer or JVC service counter for replacement of the rechargeable battery. If you attempt to disassemble this unit for purposes other than disposal, it may damage the unit.
Warning: Do not open, the rechargeable battery may produce an electrical shock.
If the batteries are used incorrectly, they may leak, heat or explode, and may cause fire, injury or soiling. Make note of the following: 1. Be sure to use the provided exclusive Ni-Cd battery. Do not use any other rechargeable Ni-Cd battery or dry cell battery. 2. Do not throw the battery in a fire or heat it. 3. Do not deform, take apart, modify or directly solder the battery. 4. Do not remove or damage the covering tube. 5. If any liquid from the battery gets into your eyes, it may cause blindness. If battery liquid does get into your eyes, do not rub them, but instead immediately wash them thoroughly with clean water, then consult a doctor at once. Also, should any liquid from the rechargeable battery get onto your skin or clothes, it may burn your skin. In this case, wash with clean water immediately. 6. Do not immerse or wet the battery in water. 7. Do not use or leave the battery in an area where the temperature becomes significantly higher, such as in direct sunlight, inside a car on hot day or near heat-generating equipment. 8. Do not subject the battery to strong shocks or throw it.

OTHER CAUTIONS

1. Caution! To avoid risk of fire or injury, do not attempt to charge non-rechargeable batteries. 2. Replace only with the same type recommended by the manufacturer. 3. Please dispose of old, defective batteries in an environmentally friendly manner in accordance with the relevant legislation. 4. No naked flame sources, such as lighted candles, should be placed on the apparatus. 5. The unit shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on or by the unit. 6. For indoors use only. Do not expose to rain. 7. Dont open, no user serviceable parts inside.

Page 12

HOW TO USE
1. Connect the transmitter and AV equipment. (Refer to page 7) 2. Connect the AC adaptor to the transmitter, then plug the AC adaptor into an AC outlet. (Refer to page 8) 3. Turn on the power on the transmitter and the connected AV equipment.
5. Adjust the volume control of the connected AV equipment and the headphones, and set them to the desired listening level. 6. Turn the TUNING control to get the best reception in the headphones. In cases of interference or too much noise, select the CHANNEL switch on the transmitter to another position, then repeat step 6.
To set optimum signal reception, adjustments should be done within a range of approx. 7 m between the transmitter and the headphones.
Transmitter power When an audio signal is input, the transmitters power is turned on automatically, and the indicator lights in green. Also, when no audio signal is input for about a minute, the indicator goes out automatically and the power turns off. (Automatic Power On/Off function) The Automatic Power On/Off function is activated from audio on the left channel. The function may not activate properly in situations when the audio signal is detected only from the right channel. In some situations, the power may not be turned on automatically by the input sound (e.g. a song with a quiet opening or gradual fade-in). This is not a malfunction.

Within approx. 7 m VOL.

MAX. MIN.
4. Turn on the headphones power. To avoid excessive volume, first set the headphones volume to a low level.
Tips for better use For improved sound quality, set the volume level of the connected equipment as high as possible without causing distortion, while setting the volume level of the headphones to a slightly lower level.

After use

Keep the headphones power off. Notes: 1. When using the headphones, dont raise the volume excessively. Continuous listening for a long time at high volumes may damage your hearing. 2. For safety reasons, do not use the headphones while riding a bicycle or driving a motorcycle, car, etc.
Before using the headphones for the first time, charge the rechargeable Ni-Cd battery.

Page 14

TROUBLESHOOTING
What appears to be a malfunction may not always be serious. First make sure. Symptoms

No sound.

SPECIFICATIONS
General Specifications Modulation system Carrier frequency Usable area (distance to reach) : Stereo frequency modulation system : MHz : Max. 100 m (328 ft) (using JVC measurement systems, under controlled ambient conditions) : 30 15,000 Hz : Less than 4% (at 1 kHz) : DC 9 V (with the exclusive AC adaptor) : 3.5 mm dia. stereo miniplug : 25k : 300 mV : 100 (W) x 100 (D) x 106 (H) mm (3-15/16 x 3-15/16 x 4-3/16) (including antenna) : 115 g (4.1 oz) (without connection cord and AC adaptor) : Rechargeable Ni-Cd battery (1.2 V) x 2 : 20 hours (when charged for 24 hours) : 280 g (9.9 oz) (with installed rechargeable Ni-Cd battery x 2) x1 x1 x 1 (converts 3.5 mm dia. stereo miniplug to a 6.3 mm dia. standard stereo phone plug)
Is the transmitters power OFF?

Remedy

Check the connection of the transmitter. Turn the power on the connected AV equipment ON and start playing. Turn on the headphones power. (The indicator lights.) Fully charge the headphones. Adjust the volume of the headphones to the appropriate level.
Frequency response Distortion Power requirements Audio input terminal Input impedance Reference input level Dimensions Mass Power requirements Battery running time Mass Provided Accessories Instructions AC adaptor Plug adaptor
Is the headphones power OFF? Is the battery in the headphones exhausted? Is the volume of the headphones set to the minimum level?

Transmitter (J22121-001)

Is the volume of the connected AV Raise the volume level of the equipment set to the minimum connected AV equipment as high level? as possible without causing distortion. No sound from the R-channel. Distorted sound. Is the transmitter connected to equipment with monaural audio output? Is the battery in the headphones exhausted? Connect them with an optional plug adaptor. (Converts monaural audio output to stereo audio output.) Fully charge the headphones.

Headphones (HA-W500RF)

Is the volume of the connected AV Adjust the volume level of the equipment set too high? connected AV equipment as high as possible without causing distortion. Noisy sound. Is the battery in the headphones exhausted? Are the frequency modulation signals being received correctly? Fully charge the headphones. Turn the TUNING controls on the headphones or select the CHANNEL on the transmitter to adjust them.
Connection cord x 1 (3.5 mm dia. stereo minijack RCA pin plug x 2: 0.1 m (0.3 ft))

Is the volume of the connected AV Adjust the volume level of the equipment set too low? connected AV equipment as high as possible without causing distortion. Are the headphones too far away from the transmitter? Battery charging is impossible. Has the rechargeable Ni-Cd battery expired? Use them within the range the frequency modulation signal can reach. (Refer to page 8.) Replace it with a new Ni-Cd battery. Please consult your dealer for replacement.
* Design and specifications subject to change without notice.

Oct. 18, 2002 Headphones

HA-G77

HA-G55

HA-G33

HA-G11

HA-DX3

HA-DX1

HA-V560

HA-P75

HA-CD68

HA-CD71F-B/G/Y

Driver Unit Frequency Response Nominal Impedance Sensitivity Cord Length Max. Input Capability Weight (without cord) Plug Accessory
50mm dia. 10 25,000Hz 32 ohms 100dB/1mW 3.5m 100mW 260g Gold plated Plug adapter
50mm dia. 14 25,000Hz 32 ohms 98dB/1mW 3.5m 100mW 270g Gold plated Plug adapter
40mm dia. 16 22,000Hz 32 ohms 100dB/1mW 3.5m 50mW 190g Gold plated Plug adapter
30mm dia. 18 22,000Hz 32 ohms 98dB/1mW 3m 50mW 150g Nickel plated Plug adapter
50mm dia. 4 30,000Hz 90 ohms 98dB/1mW 4m OFC 100mW 340g Gold plated Plug adapter (screw-type)
50mm dia. 5 30,000Hz 45 ohms 98dB/1mW 4m OFC 100mW 300g Gold plated Plug adapter
40mm dia. 7 21,000Hz 32 ohms 103dB/1mW 3m 50mW 120g Gold plated Plug adapter
30mm dia. 10 23,000Hz 32 ohms 108dB/1mW 1.5m 50mW 125g Gold plated
30mm dia. 15 22,000Hz 32 ohms 98dB/1mW 7m 50mW 58g Gold plated
30mm dia. 8 22,000Hz 32 ohms 98dB/1mW 2m 50mW 48g Gold plated

HA- CD59

HA-37-BU/PN/GN/WT/YL

HA-E5-BU/SL

HA-E3-BK/BU/RD/SL

HA-B27-SL

HA-B25-BU/SL

HA-B15-BU/SL

HA-B7-BU/SL
Driver Unit Frequency Response Nominal Impedance Sensitivity Cord Length Max. Input Capability Weight (without cord) Plug
30mm dia. 15 22,000Hz 32 ohms 100dB/1mW 2m 50mW 58g Gold plated
30mm dia. 17 25,000Hz 32 ohms 100dB/1mW 1.5m 50mW 43g Nickel plated
30mm dia. 17 25,000Hz 32 ohms 100dB/1mW 1.5m 50mW 47g Nickel plated
30mm dia. 14 24,000Hz 32 ohms 91dB/1mW 1.2m 30mW 34g Gold plated
27mm dia. 18 24,000Hz 32 ohms 94dB/1mW 1.2m 30mW 26g Nickel plated
30mm dia. 8 24,000Hz 32 ohms 103dB/1mW 1.5m 30mW 48g Gold plated
30mm dia. 8 20,000Hz 32 ohms 108dB/1mW 1.5m 30mW 54g Gold plated
30mm dia. 10 20,000Hz 32 ohms 108dB/1mW 1.5m 30mW 48g Gold plated
30mm dia. 15 20,000Hz 32 ohms 98dB/1mW 1.5m 30mW 46g Gold plated

HA-F90

HA-F70

HA-F50

Frequency Response Nominal Impedance Sensitivity Cord Length Max. Input Capability Weight (without cord) Plug Accessory
16 22,000Hz 16 ohms 103dB/1mW 1.2m 20mW 6g Gold plated Travel pouch
16 22,000Hz 16 ohms 103dB/1mW 1.2m 20mW 6g Gold plated
16 22,000Hz 16 ohms 103dB/1mW 1.2 m 20mW 6g Nickel plated
Type Impedance Sensitivity Cord Length Max. Input Capability Weight (without cord) Plug
Moving coil 25 ohms 116dB/1mW 3m with 3.5mm dia. miniplug 50mW 13g Nickel plated

HA-SU700

HA-W500RF
GENERAL Frequency Response Power Requirements Cord Length Weight (without cord) WHEN SRS IS ON Input Impedance Distortion Battery Running Time 500 ohms Less than 0.3% (at 1kHz) Approx. 70 hours (when manganese battery is used) Approx. 140 hours (when alkaline battery is used) WHEN SRS IS OFF Sensitivity 94dB/1mW 18 22,000Hz AA (R6P) battery x 2 (DC 3V) 7m 280g (including battery)
GENERAL Modulation System Carrier Frequency Usable Area Frequency Response Distortion TRANSMITTER Power Requirements Audio Input Terminal Input Impedance Reference Input Level Dimensions (W x H x D) Weight DC 9V (with exclusive AC adapter) 3.5mm dia. Stereo miniplug 25 k-ohms 300mV 100 x 106 x 100mm (including antenna) 115g (without connection cord and AC adapter) HEADPHONES Power Requirements Battery Running Time Weight Rechargeable Ni-Cd battey (1.2V) x hours (when charged for 24 hours) 280g (with installed batteries) Stereo frequency modulation 863 865MHz Max. 100m (using JVC measurement system) 30 15,000Hz Less than 4% (at 1kHz)

Microphones

MV-110

MV-J3-BK

Type Directivity Sensitivity Frequency Response Impedance Cord Length Weight (without cord) Plug Accessory
Dynamic Unidirectional -55dB 100 16,000Hz 600 ohms 5m 270g Gold plated
Dynamic Unidirectional -55dB 100 15,000Hz 600 ohms 5m 270g Gold plated
Dynamic Unidirectional -55dB 100 13,000Hz 600 ohms 5m 145g Nickel plated Plug adapter
Dynamic Unidirectional -56dB 100 13,000Hz 600 ohms 3m 250g Gold plated Plug adapter
Dynamic Unidirectional -56dB 100 12,000Hz 600 ohms 3m 115g Nickel plated Plug adapter
P21) Headphone/Microphone (JUK)