DVD PLAYER Hi-Fi VIDEO CASSETTE RECORDER USERS GUIDE

For model: HR-XV1EU

DIGITAL VIDEO

LPT0715-001A

2A73501AE Cover

4/17/02, 8:23 PM

Safety Precautions

SAFETY FIRST

The rating plate and the safety caution are on the rear of the unit.
WARNING: DANGEROUS VOLTAGE INSIDE WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. CAUTION
When you are not using the recorder for a long period of time, it is recommended that you disconnect the power cord from the mains outlet. Dangerous voltage inside. Refer internal servicing to qualified service personnel. To prevent electric shock or fire hazard, remove the power cord from the mains outlet prior to connecting or disconnecting any signal lead or aerial.

CAUTION:

A DVD/VCR IS A CLASS 1 LASER PRODUCT. HOWEVER THIS DVD/VCR USES A VISIBLE LASER BEAM WHICH COULD CAUSE HAZARDOUS RADIATION EXPOSURE IF DIRECTED. BE SURE TO OPERATE THE PLAYER CORRECTLY AS INSTRUCTED. THE FOLLOWING CAUTION LABEL IS LOCATED ON THE REAR PANEL OF THE DVD/VCR.

CLASS 1 LASER PRODUCT

WHEN THIS DVD/VCR IS PLUGGED INTO THE WALL OUTLET, DO NOT PLACE YOUR EYES CLOSE TO THE OPENING OF THE DISC TRAY AND OTHER OPENINGS TO LOOK INTO THE INSIDE OF THIS DVD/ VCR. USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. DO NOT OPEN COVERS AND DO NOT REPAIR YOURSELF. REFER SERVICING TO QUALIFIED PERSONNEL.

IMPORTANT

Please read the various precautions on page 2 and 3 before installing or operating the recorder. It should be noted that it may be unlawful to re-record pre-recorded tapes, records, or discs without the consent of the owner of copyright in the sound or video recording, broadcast or cable programme and in any literary, dramatic, musical, or artistic work embodied therein. Use only discs marked with the following. DVD [8 cm disc/12 cm disc] Video CDs/Audio CDs [8 cm disc/12 cm disc]
Cassettes marked VHS (or S-VHS) can be used with this video cassette recorder. However, S-VHS recording is not possible with this model. This model is equipped with SQPB (S-VHS QUASI PLAYBACK) that makes it possible to play back S-VHS recordings with regular VHS resolution. HQ VHS is compatible with existing VHS equipment. SHOWVIEW is a registered trademark of Gemstar Development Corporation. The SHOWVIEW system is manufactured under licence from Gemstar Development Corporation.

2A73501AE(02-05)

For ItaIy: It is declared that this product, brand JVC, conforms to the Ministry Decree n. 548 of 28 Aug.95 published in the Official Gazette of the Italian Republic n. 301 of 28 Dec.95
The STANDBY/ON button does not completely shut off mains power from the unit, but switches operating current on and off. shows electrical power standby and I shows ON. Video tapes recorded with this video recorder in the LP (Long Play) mode cannot be played back on a singlespeed video recorder.
When the equipment is installed in a cabinet or a shelf, make sure that it has sufficient space on all sides to allow for ventilation (10 cm or more on both sides, on top and at the rear.) When discarding batteries, environmental problems must be considered and the local rules or laws governing the disposal of these batteries must be followed strictly. Failure to heed the following precautions may result in damage to the recorder, remote control or video cassette. 1. DO NOT place the recorder.. in an environment prone to extreme temperatures or humidity. in direct sunlight. in a dusty environment. in an environment where strong magnetic fields are generated. on a surface that is unstable or subject to vibration. 2. DO NOT block the recorders ventilation openings or holes. (If the ventilation openings or holes are blocked by a newspaper or cloth, etc., the heat may not be able to get out.) 3. DO NOT place heavy objects on the recorder or remote control. 4. DO NOT place anything which might spill on top of the recorder or remote control. (If water or liquid is allowed to enter this equipment, fire or electric shock may be caused.) 5. DO NOT expose the apparatus to dripping or splashing. 6. DO NOT use this equipment in a bathroom or places with water. Also DO NOT place any containers filled with water or liquids (such as cosmetics or medicines, flower vases, potted plants, cups, etc.) on top of this unit. 7. DO NOT place any naked flame sources, such as lighted candles, on the apparatus. 8. AVOID violent shocks to the recorder during transport. MOISTURE CONDENSATION Moisture in the air will condense on the recorder when you move it from a cold place to a warm place, or under extremely humid conditions-just as water droplets form in the surface of a glass filled with cold liquid. Moisture condensation on the head drum will cause damage to the tape. In conditions where condensation may occur, keep the recorder turned on for a few hours to let the moisture dry.

picture (you see 2 programs 3 If there is interference in thecalled Ghosts), change the simultaneously or what is sending channel in DVD/VCR. To do this, go back to the step 1. Use PR button on the DVD/VCR to change the number next to the rF:. Then return to step 2 and tune the television newly.

4 Press

button to turn off the DVD/VCR.
Note: If you receive one TV-program on channel 35, 36 or 37, the interference can be occurred to the built-in TV channel in DVD/VCR. If you use a scart cable for the transmission of picture and sound, you can cut off the built-in TV-program. Then the video playback through the supplied antenna cable is not possible any more. Press PR repeatedly (at step 1) until OFF will appear.(OFF appears after 69 or before 23)
2A73501AE(12-15) 13 4/17/02, 8:22 PM
Setting the On-screen language
Turn on your TV and select the AVProgram position, on which you have already set your DVD/VCR. (it will happen automatically by Scart-cable connection). So you can follow up the all setting on TV screen. Preparation: button to turn on the DVD/VCR. Press the Make sure TV/VCR/DVD switch has been slided to VCR/DVD. Then press VCR to select the VCR mode. (The VCR indicator will light) You can choose from three different languages (English, French and German) for the on-screen displays. UP 1 Press SET or MENU. the Press to select SYSTEM SETUP option, then press OK. If you use the unit for the first time and press SET UP MENU, instead of the main menu screen on the right the LANGUAGE set up menu screen in step 2 may appear. to select the 2 Press or option, then LANGUAGE press OK.
ATS (AUTO TUNING SYSTEM) TIMER REC SET VCR EXTENSION VCR SETUP CHANNEL SETUP SYSTEM SETUP SELECT : ENTER : OK EXIT : MENU
or select de3 Press language:to Englishthe(ENsired GLISH), German (DEUTSCH) or French (FRANCAIS), then press OK.
LANGUAGE/SPRACHE/LANGUE ENGLISH DEUTSCH FRANCAIS

SELECT :

OK: OK
4 Press SET UP MENU repeatedly until the TV picture appears on the screen.
NOTES: If the unit does not operate properly, or No key operation (by the unit and/or the remote control): Static electricity, etc., may affect the player's operation. Disconnect the AC power cord once, then connect it again. Both the VCR and the DVD have their own menu option (See page 41). If no buttons are pressed for more than 60 seconds, the MENU screen will return to normal TV-operation automatically.

2A73501AE(12-15) 14 4/17/02, 8:22 PM
ATS Automatic Tuning System and Auto Time/Date Setting
This VCR has a built-in TV receiver module. Before you can record a TV program, all the available TV stations must be tuned in and preset in the memory. The ATS function (Automatic Tuning System) allows all the locally available TV stations to be automatically stored and sorted according to the currently effective national station list. To accomplish this, ATS will need about 12 minutes. During this period of time the VCR cannot be used. If you wish to change the station sequence, you can later perform a removing procedure (see page 17). Preparation: button to turn on the DVD/VCR. Press the Make sure TV/VCR/DVD switch has been slided to VCR/DVD. Then press VCR to select the VCR mode. (The VCR indicator will light)
1 Press SET UP MENU. Pressdot or repeatedly until the
before ATS (AUTO TUNING SYSTEM) blinks. Then press OK.
If no channel setting is done: Press 1 of number keys at first, and then press SET UP MENU. or to 2 Press / country./ Then select the desired press the OK.
ATS (AUTO TUNING SYSTEM) AREA GERMANY HOLLAND AUSTRIA SELECT : OK : OK DENMARK ITALY SWISS

EXIT : MENU

when CHANNEL 3 The ATS setting is completeddisplay appears. MAPPING indication and the current time Press SET UP MENU repeatedly until the TV program will be displayed.
CHANNEL MAPPING 1 ARD 5 PRO ZDF 6 BRRTL 7 SWSATN3

ATS ACTIVE

HR3 WDR3 MDR3 TM3
SELECT : SKIP : CANCEL CHANGE NAME : 1 MOVE :2 EXIT : MENU
If the CLOCK SET-menu appears and 00:00 appears in the display, please set the clock manually. In this case, no station transmitting time data can be received (see page 19).
Note: If ATS is done under the bad receiving condition, one or more stations may not be found. In this case, set these stations manually.(see page 20)
2A73501AE(12-15) 15 4/17/02, 8:22 PM
Skipping unwanted TV stations
(Skip those TV stations that are not wanted to be selected by pressing the PR button.) Preparation: Turn ON the TV and set to the video input mode. Make sure TV/VCR/DVD switch has been slided to VCR/DVD. Then press VCR to select the VCR mode. (The VCR indicator will light)
1 Press SET UP MENU.to Press or
select CHANNEL SETUP. Then press OK.
2 Press or to select CHANNEL MAPPING. Then

press OK.

CHANNEL SETUP CH TUNING CHANNEL MAPPING
SELECT : ENTER : OK EXIT : MENU

Unloading

Press EJECT on the unit. Even if a tape is being played, press this button only once.
Remove the cassette tape.
Automatic tape eject This VCR will automatically rewind the tape when the tape has ended. And when the tape is rewinded to its beginning, the cassette tape will be ejected automatically.
To prevent accidental erasure
Remove the erase prevention tab with a screwdriver. Screwdriver

To record again

Cover the hole with a piece of adhesive tape.

Erase prevention tab

Adhesive tape
2A73501AE(22-27) 22 4/17/02, 8:26 PM

Cassette tape playback

Preparation: Turn ON the TV and set to the video input mode. Make sure TV/VCR/DVD switch has been slided to VCR/DVD. Then press VCR to select the VCR mode. (The VCR indicator will light) prerecorded tape 1 Load a loading a cassette tape (When without the erase prevention tab, playback will start automatically).
2 To start playback Press.
Playback will start. If the cassette has not loaded yet, will blink for 4 seconds.

To stop playback

Press 3.
To rewind the tape or forward it rapidly
Stop the playback or recording with 3. To rewind the tape: Press. To forward the tape: Press.
To stop the tape-winding, press 3. To switch to playback directly (without 3), press.
Forward/Reverse picture search mode
NOTES: This VCR selects the playback tape speed SP or LP automatically. The Cassette tape and DVD disc can be played back simultaneously. If you press VCR or DVD, the tape playback and DVD playback alternate with each other on the screen. When the tape is being winded, you can switch to picture search mode (see next page). To do this, press or and hold it down. The unit will resume the tape winding as soon as the button is released.
NTSC video cassette playback
When using a pre-recorded NTSC video cassette tape, the connected TV set must operate with a 60 Hz vertical frequency. Otherwise the on-screen picture will be affected by vertical rolling. Even if your VCR set is capable of processing NTSC video signals, the picture may be shortened vertically (appearance of black bars at the top and at the bottom of the TV screen). The dubbing of a NTSC video cassette tape to a standard PAL VCR is not possible.

2A73501AE(22-27)

4/17/02, 8:26 PM

Change the recording start-time:
The recording start-time will be set by S HOW V IEW automatically. However you can change the recording start-time manually. The time near START must blink. or repeatedly until the If it does not blink, press time blinks. Then press to change.
Recording period extension:
The recording end-time will be set by S HOW V IEW automatically. However you can extend the recording end-time manually. The time near END must blink. If it does not blink, press or repeatedly until the time blinks. Then press to extend.

Select Tape speed:

Select the recording tape speed Standard Play (SP) or Long Play (LP). Press or repeatedly until you are in SPEED-line. Then press or to select SP or LP.
2A73501AE(28-33) 32 4/17/02, 8:25 PM

Timer-Recording

Timer recording can be programmed on the TV-screen with the remote control. The built-in timer allows automatic unattended recording of up to 8 programs within 1 month. Preparation: Turn ON the TV and set to the video input mode. Make sure TV/VCR/DVD switch has been slided to VCR/DVD. Then press VCR to select the VCR mode. (The VCR indicator will light) Load a video cassette with the erase prevention tab intact. Make sure with OSD that the time and date are correct. (see page 29). Example: Timer recording for channel 1, 13:00 to 14:30 with Tape speed LP on timer program number 1. SET UP MENU. Press 1 Pressto select TIMER REC SET. or Then press OK.
stand for 2 Each linememories.one program of the 8 Select one line with OK. or. Then press
-----------------------------------------
--:---:---:---:---:---:---:---:--

---------

SELECT : / OK EXIT : MENU
the desired date with or 3 Setor number keys. Then press to accept it.
TIMER REC SET DATE 23 MON START 11:30 --:-END CH 3 TV3 SPEED SP VPS/PDC OFF SELECT : SET : / 09 EXIT : MENU
Starting time (13:00), 4 Set the time (14:30), channel (1 ending ARD), Tape speed (LP) and VPS/PDC (P.35) in the same way as the step 3. In case of an erroneous input press to go back to before step and enter again. Note: In the event of a power failure the data of the automatic recording will be maintained in the built-in memory for about 30 minutes. Also, the clock will continue to run for this period of time. Thereafter the data will be deleted. When the power resumes, the time display will change to --:-- that the timer setting will have to be set.
TIMER REC SET DATE 23 MO START 13:00 END 14:30 CH 1 ARD SPEED LP VPS/PDC ON SELECT : SET : OK : OK EXIT : MENU

.to be continued to next page
2A73501AE(28-33) 33 4/17/02, 8:25 PM
5 Press OK to accept them.
To enter other programs, repeat steps 2 through 4. To return to the normal screen, press SET UP MENU twice.

23 MON 13:00

In case of Timer progarms-overlapping
Do not overlap timer programs as portions of the conflicting programs will be lost. The first recording time has priority over the next recording time as shown in the diagram below.
8 : 00 Program 1 Program 2 Deleted Parts Program 3
Non Recorded Portion Parts

9 : 00

10 : 00

11 : 00

Press ( ) 6 display. The clock symbolstandswill appear on the and the DVD/VCR by for recording. At the same time, VCR mode will change to DVD mode automatically. You can use DVD even if the VCR is in the Timer recording mode. If you do not use the DVD, turn the power off. If the clock symbol ( ) blinks in the display in spite of the pressing of , the cassette may not have been loaded yet. (see page 22) If the cassette is ejected in spite of the pressing of , the erase prevention tab of the cassette may have been removed. (see page 22) Note: In case of the timer recording from the scart socket, proceed as follows: In step 4 press or repeatedly until the "CH" line blinks. Then press AUX repeatedly until "AV1" or "AV2" or "AV3" appears. If the clock symbol ( ) blinks when the timer recording ended, the TV program has not been completely recorded because of an insufficient tape supply. Press to cancel the timer program or press EJECT to remove the cassette tape. During timer recording standby mode, the VCR mode cannot be selected. To use the VCR, press at first, then press VCR to change to VCR mode. After you use the VCR, press again to put the VCR into timer recording standby mode.
Recording Control Settings

Prog.1

Prog.2

Prog.3

Note: The daily/weekly recording can be made continuously until the recording is canceled or the tape reaches the end. During timer recording the automatic rewinding mechanism does not function.
Confirmation/Cancellation of the Timer Recording
has been activated, to 1 If the Timerthe Timer. The clock now press will deactivate symbol ( ) disappear. Then press VCR to change to VCR mode. the 2 Press PROG. twice. All will 8 Timer memories appear.
15 TUE 17:MON 13:WED 12:15 18:00 14:30 13:00 7V SP 1V LP 4 SP
--------------------------

--:---:---:---:---:--

------
/ OK SELECT : CLEAR : CANCEL EXIT : MENU

1 Press DVD to select the DVD mode. (The DVD indicator will
light.) No Disc will appear on the screen. (If a DVD disc has already loaded, the playback will start automatically.) in the stop 2 Press SET UP MENU MENU of mode. The SETUP DVD will appear on the screen. Then press or to select Language.

No Disc

Picture TV Shape 4:3LB Video Out Select Video

: Select

: Enter
to select On-Screen 3 Press / then press OK (EnLanguage, ter).
Language On-Screen Language ENG Disc Menu Language ENG Audio Language ENG Subtitle Language ENG
/ to select desired Press 4 language: English (English), German (Deutsch) or French (Franais).
Language On-Screen Language ENG English Disc Menu Language ENG Fran ais Audio Language ENG Espa ol Subtitle Language ENG
To 5 (or make the SETUP screen disappear, press SET UP MENU RETURN).
If the DVD/VCR does not operate properly: Static electricity, etc., may affect the player's operation. Disconnect the AC power cord once, then connect it again.
2A73501AE(37-41) 41 4/17/02, 8:28 PM

Playback procedure

Preparation: Turn ON the TV and set to the video input mode. Make sure TV/VCR/DVD switch has been slided to VCR/DVD. Then press DVD to select the DVD mode. (The DVD indicator will light)
1 Press OPEN/CLOSE. The disc tray will open.
a 2 Placethedisc onto the tray. the Hold disc, position it with printed label side up, align it with the guides, and place it in its proper position. Press or 3 The disc trayOPEN/CLOSE. closes automatically. On the screen, changes to and then playback will commence. A menu screen may appear on the TV screen, if the disc has a menu feature. In this case, or OK to press , , , operate a menu feature. 3 to end 4 Press DVD/VCRplayback. the stopped point, depending on The memorizes the disc. To Return To The Last Scene Viewed, Press Play. To Disable This Operation, Press STOP Again. appears on the screen for approx. 4 seconds. will continue blinking in the display until the playback is stopped completely. Press to resume playback (from the scene point). If you press 3 again ( 3 appears on the screen) or unload the disc, the DVD/VCR will clear the stopped point. press 5 Thendisc trayOPEN/CLOSE. The opens. Remove the disc and press , (POWER). The disc tray closes automatically and DVD/VCR turns off. NOTES: If a non-compatible disc is loaded, "Please Check Disc", "Disc playback unauthorized Consult owners manual for further information" or "Parental Lock" will appear on the TV screen according to the type of loaded disc. In this case, check your disc again (See pages 40 and 50, 51). Some discs may take a minute or so to start playback. may appear at the upper right of the screen. This symbol means either the feature you A Prohibition symbol tried is not available on the disc, or the DVD/VCR can not access the feature at this time. This does not indicate a problem with the DVD/VCR. or OPEN/CLOSE, " " When you set a single-faced disc label downwards (ie. the wrong way up) and press will appear and remain on the screen for approx. 30 seconds and then it will change to "Please Check Disc". Some playback operations of DVDs may be intentionally fixed by software producers. Since this DVD/VCR plays DVDs according to the disc contents the software producers designed, some playback features may not be available. Also refer to the instructions supplied with the DVDs. When playing DTS-encoded Audio CDs, excessive noise will be heard from the analog stereo outputs. To avoid possible damage to the audio system, the consumer should take proper precautions when the analog stereo outputs of the DVD/VCR are connected to an amplification system.

Note: If you use the connection with S-Video cord, be sure to set the Video Out Select at step 2 above to Video. If you select RGB, the TV screen will be disturbed. If you selected RGB at step 2 above, press TV/VCR to select VCR. (VCR indicator will appear on the display) Otherwise, the TV screen will be disturbed when you select the channel with TVs CHANNEL UP/DOWN buttons.

Zooming

This unit will allow you to zoom in on the frame image. You can then make selections by switching the position of the frame. playback. 1 Press ZOOM duringthe image The center part of will be zoomed in. As you repeatedly press the OK or ZOOM while ZOOM is selected, the magnification level changes. Variation of the levels includes image reduction. Note: Picture Signal Selection is only available for connecting with a 21 pin Scart Cable. Depending on your TV, NTSC disc may not playback correctly in colour. In this case, it is recommended to select the Picture Signal RGB on step 2. Only use RGB setting if your TV is RGB compatible.

ZOOM EXIT

Zoom Off : Select : Change
Press or to different 2 You may /move the/ frameview athe centerpart of the frame. from position to UP, DOWN, LEFT or RIGHT direction. If you select EXIT and press the OK, you can turn off the symbol mark, keeping the current magnification level. Press CANCEL to restore the zoom point to the center of the picture. While 3 turn toZOOM is selected, press ZOOM repeatedly to rea 1:1 view.
2A73501AE(42-47) 44 4/17/02, 8:27 PM

Repeat playback

Preparation: Turn ON the TV and set to the video input mode. Make sure TV/VCR/DVD switch has been slided to VCR/DVD. Then press DVD to select the DVD mode. (The DVD indicator will light) REPEAT PLAYBACK Press PLAY to select 1 Title RepeatMODE repeatedly(In case ofChapter Repeat, or All Repeat. CD, select Track Repeat or ALL Repeat ) DVD CD

Chapter Repeat

Track Repeat
repeat start 2 During playbackplaybackplayback willmode,automatically. To start repeat during stop press within about 5 seconds after you press PLAY MODE. To resume normal playback, press PLAY MODE repeatedly until Off appears on the TV-screen.

A-B Repeat Playback

A-B repeat playback allows you to repeat material between two selected points.

/ 6 Press level, to select the parental lock then press OK (Enter).

Auto Off Off On

Off On Area Code Level
You cannot play DVD discs rated higher than the level you selected unless you cancel the parental lock function. For example, when you select level 7, discs rated higher than level 7 are locked out and cannot be played. Level 1: DVD software for adults cannot be played back. Level 8: All DVD software can be played back. Select from the level 1 to level 8. The limitation will be more severe as the level number is lower.
7 To make the SETUP screen disappear, press SET UP MENU.
To change the parental lock level Follow steps 1- 6. To change your 4-digit security code 1) After selecting On or Off at step 3 press 3 four times, then press OK (Enter). The 4-digit security code is deleted. 2) Press number keys to create a new 4-digit security code at step 4.
2A73501AE(48-53) 51 4/17/02, 8:30 PM

Setting menu language

You can select the language of the disc menu messages of DVDs. Preparation: Turn ON the TV and set to the video input mode. Make sure TV/VCR/DVD switch has been slided to VCR/DVD. Then press DVD to select the DVD mode. (The DVD indicator will light)
Press guage. or to select Lan-
Press or 2 Menu Language.to select Disc
3 Press OK (ENTER). select your Press or to
desired language, then press OK (ENTER).
English French German Others Code D E
English, French, German The selected language is the first-priority Menu language. Others: Other languages can be selected (See the Table of languages on page 61). Example: Set to DE (GERMANY). Press or to select D then press to move to the right character. Then select E same as above. Then press OK (ENTER).
4 To make the SETUP screen disappear, press SET UP MENU.
2A73501AE(48-53) 52 4/17/02, 8:30 PM
Setting audio soundtrack language
The same audio soundtrack language can always be selected by your unit even if you replace the disc or turn the power off. Preparation: Turn ON the TV and set to the video input mode. Make sure TV/VCR/DVD switch has been slided to VCR/DVD. Then press DVD to select the DVD mode. (The DVD indicator will light)

or Press Language. to select

Press or 2 Language.

to select Audio
(Enter). 3 Press OKor to select your Press desired Audio Language, then press OK (Enter).
English, French, German The language you have selected will play if it is recorded on the disc. Others: If you want to select another language, enter the language code (See the Table of languages on page 61). Example: Set to DE (GERMANY). Press or to select D then press to move to the right character. Then select E same as above. Then press OK (Enter).
NOTES: If the selected language is not recorded on the disc, the original language will be heard. Some DVD discs may be played in a different language than you selected. A prior language may be programmed on the disc.
2A73501AE(48-53) 53 4/17/02, 8:30 PM
Setting subtitle language
The same subtitle language can always be selected even if you replace the disc or turn the power off. Preparation: Turn ON the TV and set to the video input mode. Make sure TV/VCR/DVD switch has been slided to VCR/DVD. Then press DVD to select the DVD mode. (The DVD indicator will light)

2 Press or Language.

to select Subtitle
3 Press OK (Enter).to select your Press or
desired language, then press OK (Enter).
English French German No Subtitle Others Code D E
English, French, German The subtitle is displayed with the selected language if it is recorded on the disc. No Subtitle: Subtitles do not appear. Others: If you want to select another language, enter the language code (See the Table of languages on page 61). Example: Set to DE (GERMANY). Press or to select D then press to move to the right character. Then select E same as above. Then press OK (Enter). NOTES: If the selected language is not recorded on the disc, the first-priority language is selected. Some DVD discs may be set to display Subtitles in a different language than you selected. A prior subtitle language may be programmed on the disc.
2A73501AE(54-57) 54 4/17/02, 8:29 PM
Setting the aspect ratio of TV screen / Setting on Screen display
You can select the aspect ratio for your TV. Preparation: Turn ON the TV and set to the video input mode. Make sure TV/VCR/DVD switch has been slided to VCR/DVD. Then press DVD to select the DVD mode. (The DVD indicator will light)
Setting the aspect ratio of TV screen
or to select Press Picture, then press or to select TV shape.
2 Press OK (Enter).to select your Press or

To make the SET UP screen disappear, press SET 3 To make the SETUP screen disappear, press SET UP 3 UP MENU. MENU. Title Stop Turn on or off a feature that automatically stops playback after a title has been viewed.
Operation then press OK Pause/Still Auto Auto Parental Lock Off Frame (Enter). Press or Title Stop Off PBC On to select Auto or Frame, then : Select : Enter press OK (Enter). Auto: For normal use. Still and fast motion images can be paused. Frame: The resolution of still pictures is improved, so that you can make a motionless picture clearer when you pause it.
Off: When playing a VIDEO CD without using the menu. On: To use the menu when playing a PBCfeatured VIDEO CD.
Press or to select Operation.
or to 2 Press Title Stop, select then press OK (Enter). Press or to select On or Off, then press OK (Enter). Off: On:
Operation Pause/Still Parental Lock Title Stop PBC Auto Off Off On
The DVD/VCR continues after playback of a title is completed. The DVD/VCR stops after playback of a title is completed.
2A73501AE(54-57) 57 4/17/02, 8:29 PM
Selecting the sound enhancement (E.A.M.)/Setting Background/ Setting Screen Saver
Preparation: Turn ON the TV and set to the video input mode. Make sure TV/VCR/DVD switch has been slided to VCR/DVD. Then press DVD to select the DVD mode. (The DVD indicator will light) Setting Background Select the background color or background picture.
or to sePress lect Display.
Selecting the sound enhancement (E.A.M.*)
You can easily switch a preferred audio enhancement. *E.A.M.: Enhanced Audio Mode

1 Press OSD twice.

Then press B/A to A select the E.A.M. icon, then press OK (Enter). The sound enhancement menu appears.

-0:21:28

or 2 Press Backselect
ground, then press OK (Enter). Press or to select your desired background, then press OK (Enter).
Display On-Screen Display On Background Picture Screen Saver On

Blue Gray Picture Jacket

Select the sound enhancement by pressing /. 2 Each time you press the button, the sound enhancement changes.
Normal: Normal sound. 3D: To obtain expansive virtual surround sound effects from just two speakers. Dialogue: To control critical center channel information to make dialogue more intelligible (only when playing a DVD video disc recorded on the Dolby Digital recording system). To use this enhancement on sounds output from the BITSTREAM/PCM jack, be sure to set Audio Out Select to PCM. (see page 56).
Blue: Blue background. Gray: Gray background. Picture: Use the picture which appears when you turn on the DVD/VCR as a background. Jacket: Use the jacket picture included on some discs as a background. If it is not included, a gray background will be substituted.
Setting Screen Saver (DVD only) To turn the screen saver on or off.
Press or to select Display.
To exit the audio enhancement selection Press

No sound.

The remote control does not function.
The DVD-keys on the RCU of the other JVC RECEIVER/TV is not effective. VCR TV recording does not work.
The erase prevention tab of the video cassette is broken off. The unit is in the external input mode. The time is not set correctly. The recording start/end time is not set correctly. The has not been pressed ( is not lit). Tracking adjustment beyond range of automatic tracking circuit. Try Manual tracking adjustment. Video heads are dirty. The tape is worn or damaged.
Timer recording does not work.

Noise bars on screen.

DVD Display is not shown in your language. Playback doesnt start. Stopping playback, slow-motion play, repeat play, or memory play, etc. cannot be performed. Select proper language in the menu options. No disc is inserted. The disc may be dirty. Clean up the disc. The unit cannot play DVD-ROMs, etc. Some discs may not do some of the functions.
2A73501AE(58-BACK) 62 4/17/02, 8:29 PM
Problems and troubleshooting / Video head cleaning
SYMPTOMS No 4:3 (16:9) picture No on-screen display No surround sound The unit or remote operation key is not functioning. Playback does not start when the title is selected. Audio soundtrack and/or subtitle language is not changed when you play back a DVD. No subtitle Angle cannot be changed. appears on the screen. POSSIBLE SOLUTIONS The setup does not match your TV. Select Display On. The setup does not match your stereo system. Turn off the unit and unplug the AC power cord for several minutes, then replug it. Check the Parental control setting. Multilingual language is not recorded on the DVD disc. Some discs have no subtitles. Subtitles are cleared. Press SUB TITLE. Multi-angles are not recorded on the DVD disc. The function is prohibited with the unit or the disc. PAGE 50 53,

Video head cleaning

Video head clogging The video heads are the means by which the DVD/VCR reads the picture from the tape during playback. In the unlikely event that the heads become dirty enough to be clogged, no picture will be played back. This can easily be determined if, during playback of a known good tape, there is good sound, but no picture (picture is extremely snowy). If this is the case, have the DVD/VCR checked by qualified service personnel.

Good Picture

Snowy Picture
NOTES: DO NOT ATTEMPT TO CLEAN THE VIDEO HEADS OR SERVICE THE UNIT BY REMOVING THE REAR COVER. Video heads may eventually wear out and should be replaced when they fail to produce clear pictures. To help prevent video head clogging, use only good quality VHS tapes. Discard worn out tapes.

2A73501AE(58-BACK) 63 4/17/02, 8:29 PM

Specifications

GENERAL Power supply: Power consumption: AC 230V 50Hz Operation: 22W Stand by: 5W Weight: 4.5 kg Dimensions: Width : 430 mm Height : 99 mm Depth : 310.5 mm Input Level: SCART-socket: VIDEO: 1 Vp-p, 75 AUDIO: 500 mV, 50 k Audio IN jack: 500 mV, 50 k Output Level: SCART-socket: VIDEO: 1 Vp-p, 75 AUDIO: 500 mV, 1 k Audio OUT jack: 500 mV, 1 k Hi-Fi Frequency Response: 20Hz to 20,000Hz Hi-Fi Dynamic Range: More than 75dB VCR section Video Head: Audio Track: Channel covevage: RF Channel Output: F.FWD/REW Time at 25C: DVD section Signal system: Applicable disc: Audio characteristics: Frequency response: S/N Ratio: Harmonic distortion: Wow and flutter: Dynamic range: Output: Pickup:
4 Rotary Heads Hi-Fi Sound - 2 Tracks / MONO Sound - 1 Track 2-12, X, Y, Z, S1-S41, 21-69 UHF channel 36 (23 to 69) Approx. 1minute and 48 seconds (with E-180 Cassette Tape)
PAL DVD (12cm, 8cm), CD (12cm, 8cm) DVD: 4Hz - 22KHz CD: 4Hz - 20KHz 90dB 1% Below Measurable Level 90dB Audio : (RCA) 500 mV, 1Kohm Digital Audio : 0.5Vp-p/75 ohm CD : Wavelength: 775 - 805 nm Maximum output power: 0.5 mW DVD : Wavelength: 640 - 660 nm Maximum output power: 1.0 mW Remote control x ohm Coaxial Cable x 1 Battery (UM-3) x 2

ACCESSORIES:

2A73501A U 02/04

2A73501AE(58-BACK)

02.4.18, 1:38 PM

S p e c i f i c a t i e s

DVD Receiver

RX-DV3R SPECIFICATIONS AMPLIFIER SECTION Output Power (IEC 268-3/DIN) Stereo 80 watts per channel, min. RMS, driven into 8 ohms at 1kHz, with no more than 0.9% total harmonic distortion (Front & Centre Channels) 80 watts x 3, min. RMS, driven into 8 ohms at 1kHz, with no more than 0.8% total harmonic distortion (Surround Channels) 80 watts x 2, min. RMS, driven into 8 ohms at 1kHz, with no more than 0.8% total harmonic distortion 0.8%* at 80W, 8 ohms, 1kHz 240mV/47k ohms 87dB/67dB 20Hz - 20kHz (1dB) 10dB (100Hz) 10dB (10kHz) 87.5 - 108MHz 522 - 1,629kHz 500 Lines 0.7Vp-p/75 ohms 1.0Vp-p/75 ohms 0.286Vp-p/75 ohms 1.0Vp-p/75 ohms 435 x 100 x 403.5 8.0 *Measured by JVC Audio Analysis System. RX-DV3R FEATURES DVD SECTION MECHANISM/SERVO Type Playable Formats
DVD Video Player/Hi-Fi VHS Stereo Video Cassette Recorder
HR-XV1EU SPECIFICATIONS DVD SECTION AUDIO Dynamic Range Frequency Response VIDEO Output Level VCR SECTION Format Tuner Recording Speeds SQPB ShowView Auto PDC/VPS CONNECTORS Front Rear A/V IN SCART 1 (IN/OUT) SCART 2 (IN/DECODER) RGB OUT S-VIDEO OUT OPTICAL DIGITAL OUT COAXIAL DIGITAL OUT AUDIO OUT (STEREO) mm q q q SCART 1 q q q q 430 x 99 x 311 VHS PAL BG/DK SP/LP q q q RGB Composite 0.7Vp-p/75 ohms 1Vp-p/75 ohms

Surround

CD DVD
90 dB 4Hz - 20kHz 4Hz - 22kHz
Total Harmonic Distortion Input Sensitivity/Impedance Signal-to-Noise Ratio (66 IHF/DIN) Frequency Response Tone Control TUNER SECTION Tuning Range VIDEO SECTION Horizontal Resolution Output Level
VCR/TV/DBS/TAPE VCR/TV/DBS/TAPE VCR/TV/DBS/TAPE Bass Treble FM AM
RGB S-Video -Y -C Composite mm kg
GENERAL Dimensions (W x H x D) Mass Dimensions (W x H x D )

CD Recorder

XL-R910 Single DVD-Video CD SVCD/VCD CD-R/RW MP3 (CD-R/RW) JPEG (CD-R/RW) q q q q q q q 10-bit/54MHz 7 q q q q q q q q (10 Steps) New GUI (Graphical User Interface) On-Screen Language Numerical Bit-Rate Indicator Language Indicator Screen Saver SPECIFICATIONS CD RECORDER SECTION Sampling Frequency Frequency Response Minimum Input Level Signal-to-Noise Ratio Dynamic Range (1kHz) GENERAL Number of Parameters Number of Presets (Presets 2/Manual 2) Dimensions (W x H x D) Mass FEATURES Type CD PLAYER SECTION Playable Media CD CD-R/RW for Music (Finalised/Unfinalised) q q q q 30 q q q q q q Manual (2x) Manual (2x) 2x q q q q q (Output) q 1-CD/CD-R/RW mm kg 270 x 95 x 353 3.4 44.1kHz 20Hz - 20kHz 300mV (Full scale -12dB) 90dB (Playback) 90dB (Playback)

Analogue (LINE IN)

NTSC Playback on PAL TV VIDEO Video D/A Converter VFP (Video Fine Processor)
Variable Search (Forward/Reverse) Variable Slow (Forward/Reverse) RESUME (Bookmark) Function DIGEST Play (9 Pictures) STROBE Play (9 Pictures) ANGLE LIST (9 Angles) ZOOM Play GENERAL On-Screen Display
q Eng./Fre./Ger. q q q 96kHz/24-bit q q q q q Audio Digital Optical Coaxial x x x/ x q q q q q q q q q q q 30 FM and 15 AM Multi-Brand A/V 1
Smart Random Play Programme Play Number of Programmes Repeat Play Search (Track/Manual/Direct) CD-R/RW SECTION REC Source Line (Digital/Analogue) Rec Level Control (Analogue In) Synchro Rec Digital All Tracks Digital 1 Track Finalise (CD-R: 2x/CD-RW: 2x) Unfinalise (CD-RW Only) Erase (Last Single Track/Last Multiple Tracks/All Tracks) OPC/Running OPC Auto/Manual Track Marking GENERAL Line Input/Output Optical Digital Input/Output Coaxial Digital Input/Output Remote Control Unit 21-Pin Scart q q q

CIRCUITRY Audio D/A Converter (P.E.M. D.D. Converter) Surround Sound Dolby Digital Decoder Built-in DTS Decoder Built-in Dolby Pro Logic II DAP for 2-Channel Sources HALL/DANCE CLUB/ LIVE CLUB/PAVILION/ ALL CH STEREO PCM/Dolby Digital/DTS Digital Out INPUT/OUTPUT x: Assignable / : Initial Settings (Default) Analogue TV IN STB IN TAPE/CDR (ASSIGNABLE) IN/OUT VCR IN/OUT Total Number of Inputs Total Number of Outputs Pre-Out Subwoofer Speaker Terminals Main L/R Centre Surround FUNCTIONS On-Screen Display Fluorescent Display Tone Control Balance TUNER RDS Tuner: PS/PTY/RT, PTY Search TA/NEWS/INFO Number of Presets MISCELLANEOUS Remote Control Unit Dot-Matrix Display Dimmer Bass Treble