Pocket Compartimiento Poche
Bracket *2 Mnsula *2 Support *2
Flat type screwsM5 x 8 mm (M5 x 3/8") *2 Tornillos tipo planoM5 x 8 mm (M5 x 3/8 pulgada) *2 Vis tte plateM5 x 8 mm (M5 x 3/8 pouces) *2
Install the receiver at an angle of less than 30. Instale la unidad a un ngulo de menos de 30. Installez lappareil avec un angle de moins de 30.
: When installing the receiver on the mounting bracket, make sure to use the 8 mm (3/8") -long screws. If longer screws are used, they could damage the receiver. Nota : Cuando instala la unidad en la mnsula de montaje, asegrese de utilizar los tornillos de 8 mm (3/8 pulgada) de longitud. Si se utilizan tornillos ms largos, stos pueden daar la unidad. Remarque : Lors de linstallation de lappareil sur le support de montage, sassurer dutiliser des vis dune longueur de 8 mm (3/8 pouces). Si des vis plus longues sont utilises, elles peuvent endommager lappareil.

Removing the receiver

Before removing the receiver, release the rear section.

Extraccin de la unidad

Antes de extraer la unidad, libere la seccin trasera.

Retrait de lappareil

Avant de retirer lappareil, librer la section arrire.
Insert the two handles, then pull them as illustrated so that the receiver can be removed. Inserte las dos manijas y, a continuacin, extrigalas de la manera indicada en la ilustracin para poder desmontar la unidad. Insrez les deux poignes, puis tirez de la faon illustre de faon retirer lappareil.
Instal1-3_KD-ADV6160[J]f.indd 2

12/17/04 2:07:46 PM

ELECTRICAL CONNECTIONS
To prevent short circuits, we recommend that you disconnect the batterys negative terminal and make all electrical connections before installing the receiver. Be sure to ground this receiver to the cars chassis again after installation. Notes: Replace the fuse with one of the specified rating. If the fuse blows frequently, consult your JVC car audio dealer. It is recommended to connect to the speakers with maximum power of more than 50 W (both at the rear and at the front, with an impedance of 4 to 8 ). If the maximum power is less than 50 W, change AMP GAIN setting to prevent the speakers from being damaged (see page 37 of the INSTRUCTIONS). To prevent short-circuit, cover the terminals of the UNUSED leads with insulating tape. The heat sink becomes very hot after use. Be careful not to touch it when removing this receiver.

You can connect amplifiers to upgrade your car stereo system. Connect the remote lead (blue with white stripe) to the remote lead of the other equipment so that it can be controlled through this receiver. For amplifier only: Disconnect the speakers from this receiver, connect them to the amplifier. Leave the speaker leads of this receiver unused. For KD-ADV6160: You can switch off the built-in amplifier and send the audio signals only to the external amplifier(s) to get clear sounds and to prevent internal heat built-up inside the receiver. See page 37 of the INSTRUCTIONS (separate volume). The line output level of this receiver is kept high to maintain the hi-fi sounds reproduced from this receiver. When connecting an external amplifier to this receiver, turn down the gain control on the external amplifier to obtain the best performance from this receiver.
Remote lead Cable remoto Fil dalimentation distance
Y-connector (not supplied for this receiver) Conector en Y (no suministrado con esta unidad) Connecteur Y (non fourni avec cet appareil) To the remote lead of other equipment or automatic antenna if any Al conductor remoto de otro equipo o de la antena automtica, si hubiere Au fil de tlcommande de lautre appareil ou lantenne automatique sil y en a une
Remote lead (Blue with white stripe) Cable remoto (Azul con rayas blancas) Fil dalimentation distance (Bleu avec bande blanche)
Rear speakers Altavoces posteriores Enceintes arrire JVC Amplifier Amplificador de JVC JVC Amplificateur Front speakers Altavoces delanteros Enceintes avant JVC Amplifier Amplificador de JVC JVC Amplificateur
Only for KD-ADV6160 / Solo para KD-ADV6160 / Seulement pour le KD-ADV6160
JVC Amplifier Amplificador de JVC JVC Amplificateur Subwoofer Subwoofer Caisson de grave Only for KD-ADV6160 / Solo para KD-ADV6160 / Seulement pour le KD-ADV6160 Front speakers Altavoces delanteros Enceintes avant
*6 Signal cord (not supplied for this receiver) *6 Cable de seal (no suministrado con esta unidad) *6 Cordon de signal (non fourni avec cet appareil)
*7 Firmly attach the ground wire to the metallic body or to the chassis of the carto the place not coated with paint (if coated with paint, remove the paint before attaching the wire). Failure to do so may cause damage to the receiver. *7 Fije firmemente el cable de tierra a la carrocera metlica o al chasisa un lugar no cubierto con pintura (si est cubierto con pintura, qutela antes de fijar el cable). De lo contrario, se podran producir daos en la unidad. *7 Attachez solidement le fil de mise la masse au chssis mtallique de la voiture un endroit qui nest pas recouvert de peinture (sil est recouvert de peinture, enlevez dabord la peinture avant dattacher le fil). Lappareil peut tre endommag si cela nest pas fait correctement.
Connecting other external components / Conexin de otros componentes externos / Connexion dun autre appareil extrieur

Caution on volume setting:
Discs produce very little noise compared with other sources. Lower the volume before playing a disc to avoid damaging the speakers by the sudden increase of the output level.

*For safety.

Do not raise the volume level too much, as this will block outside sounds, making driving dangerous. Stop the car before performing any complicated operations.
*Temperature inside the car.
If you have parked the car for a long time in hot or cold weather, wait until the temperature in the car becomes normal before operating the unit. 3
EN02-07_KD-ADV6160[J]f.indd 3

12/14/04 2:25:03 PM

How to read this manual
The following methods are used to made the explanations simple and easy-to-understand: Some related tips and notes are explained in More about this receiver (see pages 50 54). Button operations are mainly explained with the illustrations as follows:
How to use the M MODE button
If you press M MODE, the receiver goes into functions mode, then the number buttons and 5/ buttons work as different function buttons.
Ex.: When number button 2 works as MO (monaural) button.

Press briefly.

Press repeatedly.

Press either one.

Time countdown indicator
Press and hold until your desired response begins. Press and hold both buttons at the same time.
To use these buttons for original functions again after pressing M MODE, wait for 5 seconds without pressing any of these buttons until the functions mode is cleared. Pressing M MODE again also clears the functions mode.
EN02-07_KD-ADV6160[J]f.indd 4

Contents

Basic operations.. 29 Changing the display information. 30 Selecting the playback modes. 31
Introduction Playable discs. 6 Control panel.. 7

Parts identification.. 7

Dual Zone operations. 32
Listening with headphones.. 32

Sound adjustments.. 33

Selecting preset sound modes. 33
Storing your own sound adjustments.. 33 Adjusting the sound. 34
Remote controller RM-RK230. 8
Main elements and features. 8

Getting started.. 10

Basic operations.. 10
Canceling the display demonstrations. 11 Setting the clock. 11

General settings PSM. 35

Basic procedure.. 35
Other main functions.. 38
Assigning titles to the sources.. 38 Detaching the control panel. 39

Radio operations.. 12

Listening to the radio.. 12
Storing stations in memory.. 13 Listening to a preset station. 14
CD changer operations.. 40

a Disc information indicators (folder), (track/file) TAG (ID3 Tag), s Main display d Source display / Volume level indicator f EQ (equalizer) indicator g Sound mode indicatorsROCK, CLASSIC, POPS, HIP HOP, JAZZ, USER also works as the time countdown indicator and level meter during play (see page 36). h Disc type indicatorsWMA, MP3 j Tuner reception indicators ST (stereo), MO (monaural) k Playback source indicators CH: Lights up for the CD changer. DISC: Lights up for the built-in DVD/CD player. l Playback mode / item indicators (disc), (folder), RND (random), RPT (repeat) / LOUD (loudness) indicator z Tr (track) indicator
EN02-07_KD-ADV6160[J]f.indd 7

12/15/04 12:06:36 PM

Remote controller
ENGLISH Installing the lithium coin battery (CR2025)

RM-RK230

Main elements and features

MONITOR CONTROL

ASPECT

DVD / RECEIVER CONTROL

+10 SOURCE 100 BAND PRESET / TITLE 10 DUAL VOL 1 TOP M 2nd VOL ENTER 7 DISC SHIFT 9 RETURN DISC+ 2 +100

/ TITLE OSD 3 MENU 6

Before using the remote controller:
Aim the remote controller directly at the remote sensor on the receiver. Make sure there is no obstacle in between.

Remote sensor

IMPORTANT:
Do not expose the remote sensor to strong light (direct sunlight or artificial lighting). For KD-ADV6160: If Dual Zone is activated (see page 32), the remote controller only functions for operating the DVD/CD player.

Warning:

Store the battery in a place where children cannot reach to avoid risk of accident. To prevent the battery from over-heating, cracking, or starting a fire: Do not recharge, short, disassemble, or heat the battery or dispose of it in a fire. Do not leave the battery with other metallic materials. Do not poke the battery with tweezers or similar tools. Wrap the battery with tape and insulate when throwing away or saving it. 8
MONITOR CONTROL 1 Monitor control buttons*1 (standby/on), MODE, ASPECT, MENU, and. DVD/RECEIVER CONTROL 2 (standby/on attenuator) button Turns on and off the power and also attenuates the sound. 3 SOURCE button Selects the source.
EN08-15_KD-ADV6160[J]f.indd 8

12/15/04 11:27:35 PM

4 BAND button Selects the FM/AM/SIRIUS bands. 5 TOP M (menu) button*2 Display the DVD and VCD*3 disc menu. 6 DUAL button*4 Activate and deactivate Dual Zone. 7 VOL + / buttons Adjusts the volume level. Also function as 2nd VOL +/ buttons when pressed with SHIFT button*4. 8 SETUP button*SHIFT button p Basic disc operation buttons*5: 7 (stop), 3 (play), 8 (pause) 3 (play) also function as ZOOM button when pressed with SHIFT button. q Advanced disc operation/tuner operation buttons*6 For advanced disc operations: /TITLE 5 / Select the titles (for DVD) or folders (for MP3/WMA). 4 / (reverse skip/forward skip) 1 / (reverse search/forward search)*5 For FM/AM tuner operations: PRESET 5 / Changes the preset stations. 4/ Functions to search for stations. For SIRIUS radio operations: PRESET 5 / Changes the categories. 4/ Changes the channels if pressed briefly. Changes the channels rapidly if pressed and held. w OSD button Display the on-screen bar. Also function as the /TITLE button when pressed with SHIFT button. You can directly select titles (for DVD) or folders (for MP3/WMA) using the number buttons (see page 18). e MENU button*2 Display the DVD and VCD*3 disc menu.

r Menu operation buttons*2 Cursor (% , , @ , #), and ENTER % / : Also function as DISC + / buttons when the source is CD-CH. t RETURN button*2 y Special function buttons DVD/VCD: (audio) DVD: (subtitle), (angle) *1 Controllable only if your monitor is one of the JVC monitors KV-MR9010 or KV-MH6510. *2 These buttons function as the number buttons when pressed with SHIFT button. *3 Only when PBC is not in use. *4 Applicable only for KD-ADV6160. *5 Not used for CD changer operations. *6 These buttons function as the +10/10 and +100/100 buttons when pressed with SHIFT button.

How to select a number

To select a number from 0 9:
To select a number greater than 9:
+100/100 buttons used only for searching MP3/WMA tracks number greater than 99. 9
EN08-15_KD-ADV6160[J]f.indd 9

12/14/04 2:25:30 PM

Getting started

Basic operations

* The control panel illustrations used in this manual is of KD-ADV6160.

Adjust the volume.

Volume level appears.
You cannot select some sources if they are not ready.

Volume level indicator

For FM/AM tuner only
Adjust the sound as you want. (See pages 33 and 34.)
To drop the volume in a moment (ATT)

For SIRIUS radio only

To restore the sound, press it again.

To turn off the power

EN08-15_KD-ADV6160[J]f.indd 10

12/14/04 2:25:31 PM

Canceling the display demonstrations
If no operations are done for about 20 seconds, display demonstration starts. [Initial: DEMO ON]see page 35.

Setting the clock

2 Set the hour and minute.
1 Select CLOCK H (hour), then adjust the hour. 2 Select CLOCK M (minute), then adjust the minute.

Finish the procedure.

4 Finish the procedure.
To check the current clock time when the power is turned off
To activate the display demonstration

In step 3 above.

EN08-15_KD-ADV6160[J]f.indd 11

12/14/04 2:25:32 PM

Radio operations

Listening to the radio

Selected band appears.
To tune in to a station manually
In step ! on the left column. 1
2 Select the desired station frequencies.
Lights up when receiving an FM stereo broadcast with sufficient signal strength.
Start searching for a station.

When a station is received, searching stops. To stop searching, press the same button again.
EN08-15_KD-ADV6160[J]f.indd 12
Storing stations in memory
You can preset six stations for each band.
FM station automatic presetting SSM (Strong-station Sequential Memory) 1
Lights up when monaural mode is activated.
2 Select the FM band (FM1 FM3)

you want to store into.

Reception improves, but stereo effect will be lost. To restore the stereo effect, repeat the same procedure. MONO OFF appears and the MO indicator goes off.
SSM flashes, then disappears when automatic presetting is over. Local FM stations with the strongest signals are searched and stored automatically in the FM band.

To be continued. 13

EN08-15_KD-ADV6160[J]f.indd 13
When an FM stereo broadcast is hard to receive

Manual presetting

Ex.: Storing FM station of 92.5 MHz into the preset number 1 of the FM1 band.
Listening to a preset station
Select the preset station (1 6) you 3
When using the remote controller.
Preset number flashes for a while.
To check the current clock time while listening to an FM or AM station
* If no title is assigned to a station, NO NAME appears. To assign a title to a station, see page 38. 14
EN08-15_KD-ADV6160[J]f.indd 14

12/14/04 2:25:33 PM

Disc operations
Playing a disc in the receiver

To be continued. 15

12/14/04 3:58:50 PM
The disc type is automatically detected, and playback starts automatically (for DVD: automatic start depends on its internal program). If the current disc is an audio CD, CD Text, MP3/WMA, or VCD without PBC, all tracks will be played repeatedly until you change the source or eject the disc. If a title list or disc menu appears while playing a DVD or VCD with PBC, see Disc menu operations on page 20.
The following marks are used to indicate the playable discs.
Before performing any operations, make sure the following. Turn on the monitor for playing a DVD or VCD. If you turn on the monitor, you can also control the audio CD, CD Text, and MP3/ WMA playback by referring to the monitor screen. (See pages 24 and 25.) For DVD playback, you can change the Setup Menu setting to your preference. (See pages 26 28.) The operations explained on pages are using the remote controller. When you want to operate the DVD/CD player using the buttons on the control panel, see Other disc operations on pages 29 31.

DVD Video

Video CD with PBC only
If appears on the monitor when pressing a button, the receiver cannot accept an operation you have tried to do. In some cases, without showing , operations will not be accepted.
Video CD with/without PBC

Audio CD/ CD Text

MP3/WMA disc

All discs listed here

Microsoft and Windows Media are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.
EN08-15_KD-ADV6160[J]f.indd 15
When inserting a DVD disc:

Total title number

When inserting a VCD:
Total playing time of the inserted disc Total track number of the inserted disc
Elapsed playing time Elapsed playing time

Current chapter number

When inserting an MP3/WMA disc:

Total folder number

When inserting a CD Text/audio CD:

Total track number

Ex.: When an MP3 file is detected
CD Text: Disc title/performer = Track title appears automatically (see page 30).
Elapsed playing Current track time number
Disc information appears automatically (see page 30).
Elapsed playing time Current track number

To eject the disc

Current folder number
*1 Either the MP3 or WMA indicator lights up depending on the detected file. *2 Does not light up for DVD-R/DVD-RW.
EN16-27_KD-ADV6160[J]f.indd 16

12/14/04 2:24:42 PM

Operations

To stop play temporarily

Display indication and/or next operation
PAUSE illuminates on the display. A still picture appears. A Frame by frame playback

B Slow motion playback

No sound comes out during Slow Motion Playback. When playing a VCD, Reverse Slow Motion Playback is prohibited. To resume normal play:
To replay the previous scenesOne Touch Replay
The playback position moves back about 10 seconds before the current position.
This function works only within the same title. For some DVDs, this function does not work. To stop playback When you start playback again, playback starts from where it has been stopped (Resume play). When you start playback again, playback starts from the beginning of the last track. * During play, on-screen guide icons appear on the monitor for a while (see page 53).

AUDIO DIGITAL AUDIO OUTPUT DOWN MIX
AUDIO DIGITAL AUDIO OUTPUT DOWN MIX D. RANGE COMPRESSION STREAM/PCM STEREO ON
STREAM/PCM DOLBY SURROUND ON

D. RANGE COMPRESSION

Ex.: When selecting the AUDIO menu
To set other items on the same menu

Repeat steps 3 to 6.

3 Select an item you want to set up.
To set other items on other menus

Repeat steps 2 to 6.

To return to the normal screen
Ex.: When selecting DOWN MIX
EN16-27_KD-ADV6160[J]f.indd 26

12/14/04 2:24:51 PM

LANGUAGE menu
Item MENU LANGUAGE AUDIO LANGUAGE SUBTITLE ON SCREEN LANGUAGE Contents Select the initial disc menu language. Select the initial audio language. Select the initial subtitle language or erase the subtitle (OFF). Select the language for the Setup menu and some indications shown on the monitor.
For the LANGUAGE settings, see also the language codes list on page 49.

PICTURE menu

Item MONITOR TYPE

16:9 4:3 LETTER BOX

Contents Select the monitor type to watch a wide screen picture on your monitor. 16:9 [MULTI]* : Select this when the aspect ratio of your monitor is 16:9. 4:3 [MULTI]* LETTER BOX : Select this when the aspect ratio of your monitor is 4:3. While viewing a wide screen picture, the black bars appear on the top and the bottom of the screen. 4:3 [MULTI]* PAN SCAN : Select this when the aspect ratio of your monitor is 4:3. While viewing a wide screen picture, the black bars do not appear; however, the left and right edges of the pictures will not be shown on the screen. * Select [MULTI] options for the multi-color system TVs. Select the on-screen bar position on the monitor. 1 : Higher position 2 : Lower position

4:3 PAN SCAN

OSD POSITION

Position 1 Position 2

To be continued. 27
EN16-27_KD-ADV6160[J]f.indd 27

12/14/04 2:24:52 PM

AUDIO menu
Item DIGITAL AUDIO OUTPUT Contents Select the signal format to be emitted through the DIGITAL OUT (Optical) terminal on the rear. For details, see page 54. PCM ONLY : Select this when connecting an amplifier or a decoder incompatible with Dolby Digital, DTS, MPEG Audio, or connecting to a recording device. DOLBY DIGITAL/PCM : Select this when connecting an amplifier or a decoder compatible with Dolby Digital. STREAM/PCM : Select this when connecting an amplifier or a decoder compatible with Dolby Digital, DTS, and MPEG Audio. When playing back a multi-channel DVD disc, this setting affects the signals reproduced through the LINE OUT jacks (and through the DIGITAL OUT terminal when PCM ONLY is selected for DIGITAL AUDIO OUTPUT). DOLBY SURROUND : Select this when you want to enjoy multichannel surround audio by connecting an amplifier compatible with Dolby Surround to this receiver. STEREO : Normally select this. You can enjoy a powerful sound at low or middle volume levels while playing a Dolby Digital software. AUTO : Select this to apply the effect to multi-channel encoded software (excluding 1-channel and 2-channel software). ON : Select this to always use this function.

2 Move to the next (or previous) character position.
You cannot assign a title to a DVD, VCD, CD Text, or an MP3/WMA disc.

1 Select the source.

For FM/AM tuner: Tune into a station. For a CD in this receiver: Insert a CD. For CDs in the CD changer: Select CD-CH, then select a disc number.
3 Repeat steps 1 and 2 until you finish entering the title.
2 Enter the title assignment mode.
To erase the entire title
In step 2 on the left column.
Ex.: When you select DISC as the source
EN36-41_KD-ADV6160[J]f.indd 38
Detaching the control panel
When detaching or attaching the control panel, be careful not to damage the connectors on the back of the control panel and on the panel holder.
Before detaching the control panel, be sure to turn off the power.
EN36-41_KD-ADV6160[J]f.indd 39

12/14/04 2:26:37 PM

Attaching the control panel

CD changer operations

Playing discs in the CD changer

About the CD changer

It is recommended to use the JVC MP3compatible CD changer with your receiver. You can also connect other CH-X series CD changers (except CH-X99 and CH-X100). However, they are not compatible with MP3 discs, so you cannot play back MP3 discs. You cannot use the KD-MK series CD changers with this receiver. Disc text information recorded in the CD Text can be displayed when a JVC CD Text compatible CD changer is connected. Before operating your CD changer: Refer also to the Instructions supplied with your CD changer. You cannot control and play any DVD, VCD, and WMA disc in the CD changer.
* If you have changed EXT IN setting to EXT IN (see page 37), you cannot select the CD changer.

Selected disc number

Select a disc.
For disc number from 01 06:
All tracks of the inserted discs in the magazine will be played repeatedly until you change the source or eject the magazine from the CD changer. For disc number from 07 12:
EN36-41_KD-ADV6160[J]f.indd 40

Current disc number

Folder name*
To go to the next or previous tracks
Current folder number To the following tracks.
Disc information appears automatically (see page 42).
To the beginning of the current track, then the previous tracks.
To go to the next or previous folders (only for MP3 discs)
* ROOT appears if no folder is included in the disc. When the current disc is an audio CD or a CD Text disc:

To skip to a track quickly during play
CD Text: Disc title/performer = Track title appear automatically (see page 42).
For MP3 disc, you can skip a track within the same folder. Ex.: To select track 32 while playing track 6

To be continued. 41

EN36-41_KD-ADV6160[J]f.indd 41
When the current disc is an MP3 disc:
To fast-forward or reverse the track
While playing an MP3 disc
When TAG DISP is set to TAG ON (see page 37) First time you press 5 or button, the track skips to the nearest higher or lower track with a track number of multiple ten (ex. 10th, 20th, 30th). Then each time you press the button, you can skip 10 tracks. After the last track, the first track will be selected and vice versa.
*2 If an MP3 file does not have ID3 tags, folder name and file name appear. In this case, the TAG indicator will not light up.
When TAG DISP is set to TAG OFF
While playing an audio CD or a CD Text
*1 If no title is assigned to an audio CD, NO NAME appears. To assign a title to an audio CD, see page 38.
EN42-49_KD-ADV6160[J]f.indd 42

12/14/04 2:26:46 PM

Repeat play Mode

TRK RPT:

The current track. RPT lights up. FLDR RPT*: All tracks of the current folder. and RPT light up. DISC RPT: All tracks of the inserted discs. and RPT light up. RPT OFF: Cancels.
FLDR RND*: All tracks of the current folder, then tracks of the next folder and so on. RND and light up. DISC RND: All tracks of the current disc. RND and light up. MAG RND: All tracks of the inserted discs. RND lights up. RND OFF: Cancels.
* Only while playing an MP3 disc.
EN42-49_KD-ADV6160[J]f.indd 43

12/14/04 2:26:47 PM

External component operations
Playing an external component
You can connect an external component to the CD changer jack on the rear using the Line Input AdapterKS-U57 (not supplied), LINE IN plug on the rear, or AUX (auxiliary) input jack on the control panel. For connection, see Installation/Connection Manual (separate volume).
Turn on the connected component and start playing the source. Adjust the volume.
LINE IN: For selecting the external component connected to the LINE IN plug. AUX IN: For selecting the external component connected to the AUX input jack. (NOT compatible with digital signals.) For selecting the external component connected to the CD changer jack on the rear. If EXT IN does not appear, see page 37 and select the external input (EXT IN). EXT IN:

EN42-49_KD-ADV6160[J]f.indd 47
To change the display information while listening to a channel

Maintenance

ENGLISH How to clean the connectors
Frequent detachment will deteriorate the connectors. To minimize this possibility, periodically wipe the connectors with a cotton swab or cloth moistened with alcohol, being careful not to damage the connectors.

To keep discs clean

A dirty disc may not play correctly. If a disc does become dirty, wipe it with a soft cloth in a straight line from center to edge. Do not use any solvent (for example, conventional record cleaner, spray, thinner, benzine, etc.) to clean discs.

To play new discs

New discs may have some rough spots around the inner and outer edges. If such a disc is used, this receiver may reject the disc. To remove these rough spots, rub the edges with a pencil or ball-point pen, etc.

Connector

Moisture condensation
Moisture may condense on the lens inside the DVD/CD player in the following cases: After starting the heater in the car. If it becomes very humid inside the car. Should this occur, the DVD/CD player may malfunction. In this case, eject the disc and leave the receiver turned on for a few hours until the moisture evaporates.
Do not use the following discs:

Warped disc

How to handle discs
When removing a disc from its case, press down the center holder of the case and lift the disc out, holding it by the edges. Always hold the disc by the edges. Do not touch its recording surface. When storing a disc into its case, gently insert the disc around the center holder (with the printed surface facing up). Make sure to store discs into the cases after use.

Center holder

Sticker

Sticker residue

Stick-on label
EN42-49_KD-ADV6160[J]f.indd 48

12/14/04 2:26:49 PM

Language codes
AA AB AF AM AR AS AY AZ BA BE BG BH BI BN BO BR CA CO CS CY DZ EL EO ET EU FA FI FJ FO FY GA GD GL GN GU HA HI HR HU HY IA IE

Language

Afar Abkhazian Afrikaans Ameharic Arabic Assamese Aymara Azerbaijani Bashkir Byelorussian Bulgarian Bihari Bislama Bengali, Bangla Tibetan Breton Catalan Corsican Czech Welsh Bhutani Greek Esperanto Estonian Basque Persian Finnish Fiji Faroese Frisian Irish Scots Gaelic Galician Guarani Gujarati Hausa Hindi Croatian Hungarian Armenian Interlingua Interlingue

IK IN IS IW JI JW KA KK KL KM KN KO KS KU KY LA LN LO LT LV MG MI MK ML MN MO MR MS MT MY NA NE NO OC OM OR PA PL PS PT QU RM
Inupiak Indonesian Icelandic Hebrew Yiddish Javanese Georgian Kazakh Greenlandic Cambodian Kannada Korean (KOR) Kashmiri Kurdish Kirghiz Latin Lingala Laothian Lithuanian Latvian, Lettish Malagasy Maori Macedonian Malayalam Mongolian Moldavian Marathi Malay (MAY) Maltese Burmese Nauru Nepali Norwegian Occitan (Afan) Oromo Oriya Panjabi Polish Pashto, Pushto Portuguese Quechua Rhaeto-Romance
RN RO RW SA SD SG SH SI SK SL SM SN SO SQ SR SS ST SU SW TA TE TG TH TI TK TL TN TO TR TS TT TW UK UR UZ VI VO WO XH YO ZU
Kirundi Rumanian Kinyarwanda Sanskrit Sindhi Sangho Serbo-Croatian Singhalese Slovak Slovenian Samoan Shona Somali Albanian Serbian Siswati Sesotho Sundanese Swahili Tamil Telugu Tajik Thai Tigrinya Turkmen Tagalog Setswana Tonga Turkish Tsonga Tatar Twi Ukrainian Urdu Uzbek Vietnamese Volapuk Wolof Xhosa Yoruba Zulu
EN42-49_KD-ADV6160[J]f.indd 49

More about this receiver

ENGLISH Basic operations

Turning on the power

By pressing SOURCE on the receiver, you can also turn on the power.

General

In this manual, words track and file are interchangeably used when referring to MP3/ WMA files and their file names. This receiver can also playback 8 cm (3-3/16") discs. This receiver can only playback audio CD (CD-DA) files if different type of files are recorded in the same disc. The first track will be skipped if a different type of file is detected first. When a disc has been loaded, selecting DISC for the playback source starts disc play.

Selecting the sources

When no disc is loaded in the receiver, DISC cannot be selected. Without connecting to the CD changer or the SIRIUS radio, CD-CH or SIRIUS cannot be selected.

Turning off the power

If you turn off the power while listening to a disc, disc play will start automatically, next time you turn on the power.

Inserting a disc

When a disc is inserted upside down, PLEASE and EJECT appear alternately on the display. Press 0 to eject the disc.

Tuner operations

During SSM search. All previously stored stations are erased and stations are stored newly. Received stations are preset in No. 1 (lowest frequency) to No. 6 (highest frequency). When SSM is over, the station stored in No. 1 will be automatically tuned in. When storing a station manually, a previously preset station is erased when a new station is stored in the same preset number.

EN50-59_KD-ADV6160[J]f.indd 52

12/15/04 9:13:29 AM

About sounds reproduced through the rear terminals
Through the analog terminals (Speaker out/LINE OUT/2nd AUDIO OUT): 2-channel signal is emitted. When playing a multi-channel encoded disc, multi-channel signals are downmixed. (AUDIODOWN MIX: see page 28.) Through DIGITAL OUT (optical): Digital signals (Linear PCM, Dolby Digital, DTS, MPEG Audio) are emitted through this terminal. (For more details, see page 54.) To reproduce multi-channel sounds such as Dolby Digital and DTS, connect an amplifier or a decoder compatible with these multi-channel sources to this terminal, and set DIGITAL AUDIO OUTPUT correctly. (See page 28.) About Dual Zone While you are listening to the radio, CD changer, or external component through the speakers built into your car compartment, you can listen to the playback sound of this DVD/CD player using the headphones connected to the 2nd AUDIO OUT plug at the same time. (For details, see page 32.)

On-screen guide icons

During play, the following guide icons may appear for a while on the monitor. : Appears at the beginning of a scene containing multi-subtitle languages (for DVD only). : Appears at the beginning of a scene containing multi-audio languages (for DVD only). : Appears at the beginning of a scene containing multi-angle views (for DVD only). : Playback : Pause : Forward Slow Motion Playback (for DVD and VCD only) : Reverse Slow Motion Playback (for DVD only) : Forward search : Reverse search
EN50-59_KD-ADV6160[J]f.indd 53

12/14/04 2:26:59 PM

Output signals through the DIGITAL OUT terminal
Output signals are different depending on the DIGITAL AUDIO OUTPUT setting on the setup menu (see page 28).
DIGITAL AUDIO OUTPUT Playback Disc
DVD 48 kHz, 16/20/24 bits Linear PCM 96 kHz, Linear PCM with DTS with Dolby Digital with MPEG Audio Audio CD, Video CD Audio CD with DTS MP3/WMA
Output Signals STREAM/PCM DOLBY DIGITAL/PCM PCM ONLY
48 kHz, 16 bits stereo Linear PCM DTS bitstream 48 kHz, 16 bits stereo Linear PCM 48 kHz, 16 bits stereo Linear PCM
Dolby Digital bitstream MPEG bitstream
48 kHz, 16 bits Linear PCM
44.1 kHz, 16 bits stereo Linear PCM / 48 kHz, 16 bits stereo Linear PCM DTS bitstream 44.1 kHz, 16 bits stereo Linear PCM 32/44.1/48 kHz, 16 bits Linear PCM
Sound modes (preset frequency level settings)
The list below shows the preset frequency level settings for each sound mode (see page 33).

Sound mode

USER ROCK CLASSIC POPS HIP HOP JAZZ

Preset equalizing values

60 Hz 00 +03 ++04 +Hz 00 +02 +03 +02 +01 +Hz +01 +kHz 02 +01 2.4 kHz 00 ++kHz 00 +02 +02 +01 +01 +kHz 00 +++01
EN50-59_KD-ADV6160[J]f.indd 54

Troubleshooting

55 What appears to be trouble is not always serious. Check the following points before calling a service center.

Symptoms

Sound cannot be heard from the speakers.

Causes

The volume level is set to the minimum level. Connections are incorrect.

Remedies

Adjust it to the optimum level. Check the cords and connections. Reset the receiver (see page 2). While Dual Zone is activated, remote controller only functions for operating the DVD/CD player. Store stations manually.
The receiver does not work at all.
The built-in microcomputer may have functioned incorrectly due to noise, etc.
Remote controller does not Dual Zone is activated work. (see page 32).
SSM automatic presetting does not work. Static noise while listening to the radio. Disc cannot be played back.

Signals are too weak.

The antenna is not connected Connect the antenna firmly. firmly. Disc is inserted upside down. Insert the disc correctly. Insert a finalized CD-R/ CD-RW or DVD-R/ DVD-RW. Finalize the CD-R/CD-RW or DVD-R/DVD-RW with the component which you used for recording. Eject the disc forcibly (see page 2). Insert the disc correctly.
CD-R/CD-RW or DVD-R/ CD-R/CD-RW or DVD-R/ DVD-RW cannot be played DVD-RW is not finalized. back. Tracks on the CD-R/ CD-RW or DVD-R/ DVD-RW cannot be skipped. Disc cannot be recognized. The DVD/CD player may have functioned incorrectly. NO DISC appears on the Disc is inserted incorrectly. display.

Disc playback

EN50-59_KD-ADV6160[J]f.indd 55

12/16/04 10:19:18 PM

Sound and picture are sometimes interrupted or distorted.
You are driving on rough roads. Disc is scratched. Connections are incorrect.
Stop playback while driving on rough roads. Change the disc. Check the cords and connections. See Installation/Connection Manual. Connect the video cord correctly. Select a correct input on the TV or monitor. Select 4:3 [MULTI] LETTER BOX. (See page 27.) Change the disc. Add the extension code <.mp3> or <.wma> to their file names. Change the disc. Record MP3/WMA tracks using a compliant application (see page 6). Change the disc. Record MP3/WMA tracks using DVD-R/DVD-RW media. Skip to another track or change the disc. (Do not add the extension code <.mp3> or <.wma> to non-MP3 or WMA tracks.)

The antenna is not connected Connect the antenna firmly. firmly. No broadcast on the selected channel. Select another channel or continue listening to the previous channel.

SIRIUS

No text information for the selected channel. UPDATING flashes on the display. The receiver is updating the channel information and it takes a few minutes to complete. Reconnect the SIRIUS radio after a few seconds.
SIRIUS radio does not work at all.
* NO CATEGORY, NO CHANNEL, NO ARTIST, NO COMPOSER, or NO SONG/PROGRAM.
EN50-59_KD-ADV6160[J]f.indd 58

12/15/04 2:49:01 PM

Specifications
Power Output: 20 W RMS 4 Channels at 4 and 1% THD+N Signal to Noise Ratio: 80 dBA (reference: 1 W into 4 )
[AM Tuner] Sensitivity: 20 V Selectivity: 35 dB

DVD/CD PLAYER SECTION

Load Impedance: 4 (4 to 8 allowance) Equalizer Control Range: Frequencies: 60 Hz, 150 Hz, 400 Hz, 1 kHz, 2.4 kHz, 6 kHz, 15 kHz Level: 10 dB Audio Output Level: KD-ADV6160: Analog (2nd AUDIO OUT): 6 mW (at 16 ) Digital (DIGITAL OUT: Optical): Signal wave length: 660 nm Output level: 21 dBm to 15 dBm Line-Out Level/Impedance: KD-ADV6160: 5.0 V/20 k load (full scale) KD-DV5100: 2.5 V/20 k load (full scale) Output Impedance: 1 k Subwoofer-Out Level/Impedance: KD-ADV6160: 2.0 V/20 k load (full scale) Color System: NTSC Video Output (composite): 1 Vp-p/75 Other Terminals: LINE IN, CD changer Signal Detection System: Non-contact optical pickup (semiconductor laser) Number of Channels: 2 channels (stereo) Frequency Response: DVD, fs=48 kHz/96 kHz: 16 Hz to Hz VCD, CD, MP3, WMA: 16 Hz to Hz Dynamic Range: 96 dB Signal-to-Noise Ratio: 98 dB Wow and Flutter: Less than measurable limit MP3 (MPEG Audio Layer 3): Max. Bit Rate: 320 kbps WMA (Windows Media Audio): Max. Bit Rate: 192 kbps

GENERAL

Power Requirement: Operating Voltage: DC 14.4 V (11 V to 16 V allowance) Grounding System: Negative ground Allowable Operating Temperature: 0C to +40C (32F to 104F) Dimensions (W H D): Installation Size (approx.): 182 mm 52 mm 158 mm (7-3/16" 2-1/16" 6-1/4") Panel Size (approx.): 188 mm 58 mm 11 mm (7-7/16" 2-5/16" 7/16") Mass (approx.): 1.7 kg (3.7 lbs) (excluding accessories) Design and specifications are subject to change without notice. If a kit is necessary for your car, consult your telephone directory for the nearest car audio speciality shop.

TUNER SECTION

Frequency Range: FM: 87.5 MHz to 107.9 MHz (with channel interval set to 200 kHz) 87.5 MHz to 108.0 MHz (with channel interval set to 50 kHz) AM: 530 kHz to kHz (with channel interval set to 10 kHz) 531 kHz to kHz (with channel interval set to 9 kHz) [FM Tuner] Usable Sensitivity: 11.3 dBf (1.0 V/75 ) 50 dB Quieting Sensitivity: 16.3 dBf (1.8 V/75 )