Fire wall Feuerwand Cloison Brandscherm Dashboard Armaturenbrett Tableau de bord Dashboard F G
Stay (option) Anker (Option) Hauban (en option) Steun (facultatief)
Screw (option) Schraube (Option) Vis (en option) Schroef (facultatief) C
Flat type screws (M5 x 8 mm)* Senkkopfschrauben (M5 x 8 mm)* Vis tte plate (M5 x 8 mm) * Platkopschroeven (M5 x 8 mm)* Bracket* Konsole* Support * Console*
Install the unit at an angle of less than 30. Stellen Sie das Gert mit einem Winkel von weniger als 30 auf. Installez lappareil avec un angle de moins de 30. Installeer het toestel met een hoek kleiner dan 30.
: When installing the unit on the mounting bracket, make sure to use the 8 mm-long screws. If longer screws are used, they could damage the unit. Hinweis : Beim Anbringen des Gert an der Konsole sicherstellen, da 8 mm lange Schrauben verwendet werden. Werden lngere Schrauben verwendet, knnen sie das Gert beschdigen. Remarque : Lors de linstallation de lappareil sur le support de montage, sassurer dutiliser des vis dune longueur de 8 mm. Si des vis plus longues sont utilises, elles peuvent endommager lappareil. Opmerking : Wanneer u het apparaat aan de bevestigingsklem vastmaakt, moet u de 8 mm lange schroeven gebruiken. Als u langere schroeven gebruikt, kan het apparaat worden beschadigd.

ELECTRICAL CONNECTIONS

To prevent short circuits, we recommend that you disconnect the batterys negative terminal and make all electrical connections before installing the unit. Be sure to ground this unit to the cars chassis again after installation. Notes: Replace the fuse with one of the specified rating. If the fuse blows frequently, consult your JVC IN-CAR ENTERTAINMENT dealer. It is recommended to connect to the speakers with maximum power of more than 50 W (both at the rear and at the front, with an impedance of 4 to 8 ). If the maximum power is less than 50 W, change AMP.GAIN setting to prevent the speakers from being damaged (see page 38 of the INSTRUCTIONS). To prevent short-circuit, cover the terminals of the UNUSED leads with insulating tape. The heat sink becomes very hot after use. Be careful not to touch it when removing this unit.

B5 B6 A5

B7 B8 A7 A8
Fuse position 2 / 2. Sicherungsposition / Position de fusible 2 / Zekering, stand 2 Fuse position 1 / 1. Sicherungsposition / Position de fusible 1 / Zekering, stand 1
15 A fuse 15 A Sicherung Fusible 15 A Zekering 15 A

*1 *1 *1 *1

Not included for this unit Wird nicht mit Gert mitgeliefert Non fourni avec cet appareil Niet bij het apparaat inbegrepen
Ignition switch Zndschalter Interrupteur dallumage Ontstekingsschakelaar

Black Schwarz Noir Zwart

To metallic body or chassis of the car Zur metallenen Karosserie oder zum Fahrwerk des Autos Vers corps mtallique ou chssis de la voiture Naar metalen ondergrond of chassis van de auto
To CD changer/DAB tuner or another external component (see diagram ) (Only for KD-G801) An CD-Wechsler/DAB-Tuner oder andere externe Komponente (siehe Diagramm ) (Nur fr KD-G801) Au changeur de CD/tuner DAB ou un autre appareil extrieur (voir le diagramme ) (Seulement pour le KD-G801) Naar CD-wisselaar/DAB-tuner of ander extern component (zie schema ) (Uitsluitend voor de KD-G801)
Yellow*2 Gelb*2 Jaune *2 Geel *2

Red Rot Rouge Rood

To a live terminal in the fuse block connecting to the car battery (bypassing the ignition switch) (constant 12 V) Zur einer stromfhrenden Anschluklemme im Sicherungsblock zum Anschlieen an die Autobatterie (Umgehen des Zndschalters) (konstant 12 V) une borne sous tension du porte-fusible connecte la batterie de la voiture (en drivant linterrupteur dallumage) (12 V constant) Naar een onder spanning staande aansluitklem in het zekeringblok die is aangesloten op de accu van de auto (u passeert de ontstekingsschakelaar) (constant 12 V) To an accessory terminal in the fuse block Zur einer Zubehranschluklemme im Sicherungsblock Vers borne accessoire du porte-fusible Naar een aansluitklem in het zekeringblok
Fuse block Sicherungsblock Porte-fusible Zekeringblok
Blue with white stripe Blau mit weiem Streifen Bleu avec bande blanche Blauw met witte streep *2 Before checking the operation of this unit prior to installation, this lead must be connected, otherwise power cannot be turned on. 2 * Vor der berprfung der Funktionsfhigkeit des Gerts vor dem Einbau, mu diese Leitung angeschlossen werden, da sonst die Stromversorgung nicht eingeschaltet werden kann. 2 * Pour vrifier le fonctionnement de cet appareil avant installation, ce fil doit tre raccord, sinon lappareil ne peut pas tre mis sous tension. *2 Voordat u controleert of het apparaat werkt (alvorens het te installeren), moet deze draad aangesloten zijn. Als dit niet het geval is, kan de stroom niet worden ingeschakeld.
To the remote lead of other equipment or power aerial if any (200 mA max.) Zum Zusatzkabel des anderen Gerts oder der Motorantenne, sofern vorhanden (max. 200 mA) Au fil de tlcommande de lautre appareil ou lantenne automatique sil y en a une (200 mA max.) Naar afstandsdraad van andere apparatuur of antenne met circuit indien aanwezig (200 mA max.)

Amplifier / Verstrker / Amplificateur / Versterker
You can connect an amplifier (and other equipment) to upgrade your car stereo system. Connect the remote lead (blue with white stripe) to the remote lead of the other equipment so that it can be controlled through this unit. For amplifier only: Disconnect the speakers from this unit, connect them to the amplifier. Leave the speaker leads of this unit unused. Only for KD-G801: The line output level of this unit is kept high to maintain the hi-fi sounds reproduced from this unit. When connecting an external amplifier to this unit, turn down the gain control on the external amplifier to obtain the best performance from this unit.
Rear speakers Hintere Lautsprecher Enceintes arrire Achterspeakers

INPUT L R

Vous pouvez connecter (un amplificateur ou autre appareil) pour amliorer votre systme autoradio. Connectez le fil de commande distance (bleu avec bande blanche) au fil de commande distance de lautre appareil de faon quil puisse tre command via cet appareil. Pour lamplificateur seulement: Dconnectez les enceintes de cet appareil et connectez-les lamplificateur. Laissez les fils denceintes de cet appareil inutiliss. Seulement pour le KD-G801: Le niveau de sortie de ligne de cet appareil est maintenu un niveau lev pour maintenir une qualit Hi-Fi pour les sons reproduits par cet appareil. Lors de la connexion dun amplificateur extrieur cet appareil, diminuez le rglage du gain sur lamplificateur extrieur pour obtenir les meilleures performances de cet appareil.
Het is mogelijk om uw autostereosysteem uit te breiden met een versterker (of andere apparatuur). Verbind de externe kabel (blauw met witte streep) met de externe kabel van het andere apparatuur zodat deze op afstand vanaf deze apparaat kan worden bediend. Alleen voor een versterker: Koppel de speakers van dit apparaat los en verbind ze aan de versterker. Gebruik de speakerdraden van dit apparaat niet. Uitsluitend voor de KD-G801: Het uitgangsniveau van het geluid is hoog om het hifi-geluid van deze eenheid te behouden. Wanneer u een extern apparaat op deze eenheid aansluit, moet u erop letten dat u de versterkingsfactor van de externe versterker laag houdt, zodat deze eenheid de beste prestaties levert.

Handling discs.. 56

MP3/WMA INTRODUCTION. 25
What are MP3/WMA?. 25 How are MP3/WMA files recorded and played back?.. 25

MP3/WMA OPERATIONS. 26

Playing a disc.. 26 Locating a file or a particular portion on a disc.. 27 Selecting the playback modes. 29

SPECIFICATIONS.. 57

BEFORE USE *For safety. Do not raise the volume level too much, as this will block outside sounds, making driving dangerous. Stop the car before performing any complicated operations.
*Temperature inside the car. If you have parked the car for a long time in hot or cold weather, wait until the temperature in the car becomes normal before operating the unit.
Thank you for purchasing a JVC product. Please read all instructions carefully before operation, to ensure your complete understanding and to obtain the best possible performance from the unit.

LOCATION OF THE BUTTONS

Control panel

Display window

9 p q w e r t y u i o ; a s d
Remote sensor (standby/on attenuator) button DISP (display) button SEL (select) button Control dial Display window TP/PTY (traffic programme/programme type) button 0 (eject) button / (angle) button 5 (up) button / +10 button MODE button For KD-G801: CD/CD-CH (CD changer) button For KD-G701: CD button For KD-G801: FM/AM DAB button For KD-G701: FM/AM button Reset button EQ (equalizer) button MO (monaural) button SSM (Strong-station Sequential Memory) button INT (intro) button RPT (repeat) button RND (random) button Number buttons / buttons 4 (control panel release) button (down) button / 10 button
f Disc information indicators (track/file), TAG (ID3 Tag), (folder) g MP3 indicator h Only for KD-G801: CH (CD changer) indicator j CD indicator k Only for KD-G801: LINE indicator l WMA indicator / Main display z RDS indicatorsTP, PTY, AF, REG x Equalizer pattern indicator Audio level indicator c EQ (equalizer) indicator v FM band indicatorsFM1, FM2, FM3 b AM band indicator n Tuner reception indicatorsST (stereo), MO (monaural) m Play mode indicators (folder), (disc), RND (random), INT (intro), RPT (repeat) , TRACK indicator. Source/clock display P LOUD (loudness) indicator Q Audio level indicator Volume level indicator

Note on One-Touch Operation: When you select a source in step 2 below, the power automatically comes on. You do not have to press this button to turn on the power.
Adjust the sound as you want. (See pages 31 33.)
To drop the volume in a moment
Press briefly while listening to any source. ATT starts flashing on the display, and the volume level will drop in a moment. To resume the previous volume level, press the button briefly again. If you turn the control dial, you can also restore the sound.

Select the source.

(For KD-G801)

(For KD-G701)

To operate the tuner (FM or AM), see pages 10 20. To play a CD, see pages 21 24. To play an MP3/WMA disc, see pages 26 30. To operate the CD changer (only for KD-G801), see pages 42 46. To operate the external component (LINE IN only for KD-G801), see page 47. To operate the DAB tuner (only for KD-G801), see pages 48 51.

To turn off the power

Press and hold for more than one second. SEE YOU appears, then the unit turns off. If you turn off the power while listening to a disc, disc play will start from where playback has been stopped previously, next time you turn on the power.

Adjust the volume.

To increase the volume

To decrease the volume

CAUTION on Volume Setting: Discs produce very little noise compared with other sources. If the volume level is adjusted for the tuner, for example, the speakers may be damaged by the sudden increase in the output level. Therefore, lower the volume before playing a disc and adjust it as required during playback.
EN07-09_G801_G701[E_EX]f.p65
Canceling the display demonstration
When shipped from the factory, display demonstration has been activated, and starts automatically when no operations are done for about 20 seconds. It is recommended to cancel the display demonstration before you use the unit for the first time. To cancel the display demonstration, follow the procedure below:

Select DEMO OFF.

DEMO OFF

DEMO ON

Finish the setting.
Press and hold SEL (select) for more than 2 seconds so that one of the PSM items appears on the display. (PSM: see pages 34 and 35.)
To activate the display demonstration, repeat the same procedure and select DEMO ON in step 3.
Select DEMO MODE if not shown on the display.

Setting the clock

You can also set the clock system to either 24 hours or 12 hours.

Set the clock system.

1 Select CLOCK24H/12H. 2 Select CLOCK 24HOUR or CLOCK 12HOUR. 1 2

Set the hour.

1 Select CLOCK HOUR if not shown on the display. 2 Adjust the hour. 1 2

* When CLOCK DISP is set to CLK DISP ON (see page 36), the current indication will soon change to the clock time.
Notes: When a CD is inserted upside down, the control panel moves down, the CD automatically ejects from the loading slot. The source changes to the previously selected source. If there is no CD in the loading slot, you cannot select CD as the source. If the current disc is a CD Text, disc title/performer and then track title will automatically appear.
EN21-24_G801_G701[E_EX]f.p65
To stop play and eject the CD
Press 0. CD play stops and the control panel moves down. The CD automatically ejects from the loading slot. If you change the source or turn the power off, CD play also stops (without ejecting the CD). Next time you select CD as the source, CD play starts from where playback has been stopped previously. To return the control panel to its previous position, press 0 again. If you keep the loading slot fully open for 1 minute, (beeps sound when the BEEP SWITCH is set to BEEP ONsee page 37) the control panel automatically returns to its previous position. Be careful not to get the disc or your finger caught in between the control panel and the unit.
To go to the next or previous tracks
Press briefly, while playing a CD, to go ahead to the beginning of the next track. Each time you press the button consecutively, the beginning of the next tracks is located and played back. briefly, while playing a CD, to go Press 4 back to the beginning of the current track. Each time you press the button consecutively, the beginning of the previous tracks is located and played back.
To go to a particular track directly
Press the number button corresponding to the track number to start its playback.
Notes: If the ejected disc is not removed for about 15 seconds, the disc is automatically inserted again into the loading slot to protect it from dust. (Disc play will not start this time.) You can eject the disc even when the unit is turned off.
To select a track number from 1 6: Press 1 (7) 6 (12) briefly. To select a track number from 7 12: Press and hold 1 (7) 6 (12) for more than one second.

To go to a track quickly (+10 and 10 buttons)
Locating a track or a particular portion on a CD
To fast-forward or reverse the track
Press and hold , while playing a CD, to fastforward the track. Press and hold 4 reverse the track.
1 Press MODE to enter the functions mode

while playing a CD.

2 Press +10 or 10.
To skip 10 tracks* forwards to the last track To skip 10 tracks* backwards to the first track * First time you press +10 or 10 button, the track skips to the nearest higher or lower track with a track number of multiple ten (ex. 10th, 20th, 30th). Then each time you press the button, you can skip 10 tracks (see How to use the +10 and 10 buttons on page 23). After the last track, the first track will be selected, and vice versa.

, while playing a CD, to

Ex. 1: To select track number 32 while playing track number 6
You can play back the current track repeatedly.
functions mode while playing a CD. (Three times) \ 10 \ 20 \ 30 (Twice) \ 31 \ 32

Track 6

2 Press RPT (repeat), while
MODE is still on the display, so that TRK RPT appears on the display. Each time you press the button, track repeat play mode turns on and off alternately.
Ex. 2: To select track number 8 while playing track number 36
(Three times) Track 36 \ 30 \ 20 \ 10
(Twice) \9\8 RPT indicator
Selecting CD playback modes
To play back tracks at random (Disc Random Play)
You can play back all tracks on the CD at random.
When track repeat play is turned on, the RPT indicator lights up on the display. The current track starts playing repeatedly.
To play back only intros (Track Intro Scan)
You can play back the first 15 seconds of each track sequentially.
functions mode while playing a CD.
2 Press RND (random), while
MODE is still on the display, so that DISC RND appears on the display. Each time you press the button, disc random play mode turns on and off alternately.
2 Press INT (intro), while MODE
is still on the display, so that TRK INT appears on the display. Each time you press the button, track intro scan mode turns on and off alternately.
(disc) and RND indicators and When disc random play is turned on, the RND indicators light up on the display. A track randomly selected starts playing. INT indicator When track intro scan is turned on, the INT indicator lights up on the display. The first 15 seconds of each track is played sequentially.
How to use the +10 and 10 buttons
To play back tracks repeatedly (Track Repeat Play)

Playing a CD Text

In a CD Text, some information about the disc (its disc title, performer, and track title) is recorded. This CD Text information will be shown automatically when you play a CD Text.

To change the display information
While playing back an MP3/WMA file, you can change the disc information shown on the display. Press DISP (display) repeatedly. Each time you press the button, the display changes to show the following:
Locating a file or a particular portion on a disc
To fast-forward or reverse the file
Press and hold while playing a disc, to fastforward the file.
When TAG DISPLAY is set to TAG DISP ON (initial setting: see page 38) Album name / performer (folder name*) ( lights up on the display) Track title (file name*) lights up on the display) Elapsed playing time and Current file number
* If ID3 tags are not recorded, folder name and file name appear. In this case, the TAG indicator will not light up on the display.
Press and hold 4 reverse the file.

while playing a disc, to

Note: During this operation, you can only hear intermittent sounds. (The elapsed playing time also changes intermittently on the display.)
To skip to the next or previous files
Press briefly while playing, to skip ahead to the beginning of the next file. Each time you press the button consecutively, the beginning of the next files is located and played back. Press 4 briefly while playing, to skip back to the beginning of the current file. Each time you press the button consecutively, the beginning of the previous files is located and played back.
When TAG DISPLAY is set to TAG DISP OFF
Folder name lights up on the display) File name lights up on the display) Elapsed playing time and Current file number
To stop play and eject the disc
Notes: The display shows up to 12 characters at a time and scrolls if there are more than 12 characters. See also To select the scroll modeSCROLL MODE on page 37. When file name is shown, TRACK indicator and current file number also appear on the lower part of the display.
To go to a particular file quickly within the current folder (+10 and 10 buttons)

while playing a disc.

To go to a particular folder directly
IMPORTANT: To directly select the folders using the number button(s), it is required that folders are assigned 2 digit numbers at the beginning of their folder names. (This can only be done during the recording of CD-Rs or CD-RWs.) Ex.: If folder name is 01 ABC = Press 1 to go to Folder 01 ABC. If folder name is 1 ABC, pressing 1 does not work. If folder name is 12 ABC = Press and hold 6 (12) to go to Folder 12 ABC. Press the number button corresponding to the folder number to start playing the first file in the selected folder.

To skip to the next or previous folder
Selecting the playback modes
To play back files repeatedly (Track Repeat/Folder Repeat Play)
You can play back the current file or all the files in the current folder repeatedly.
To play back only intros (Track Intro Scan/Folder Intro Scan)
You can play back the first 15 seconds of each file sequentially.
MODE is still on the display, so that TRK RPT or FLDR RPT appears on the display. Each time you press the button, the repeat play mode changes as follows:
2 Press INT (intro), while
MODE is still on the display, so that TRK INT or FLDR INT appears on the display. Each time you press the button, the intro scan mode changes as follows:

TRK RPT

FLDR RPT

TRK INT

FLDR INT
RPT indicator Ex.: When you select TRK RPT while listening to an MP3 file Mode TRK RPT FLDR RPT Active indicator RPT indicator lights up. and RPT indicators light up. Plays repeatedly The current (or specified) file. All files of the current (or specified) folder.
INT indicator Ex.: When you select TRK INT while listening to an MP3 file Mode TRK INT FLDR INT Active indicator Plays the beginnings (15 seconds) of
INT indicator All files on the current lights up. disc. and INT indicators lights up. The first file of every folder of the current disc.

SOUND ADJUSTMENTS

level to 00. You can adjust the sound characteristics to your preference.
*2 This takes effect only when a subwoofer is

connected.

*3 Normally the control dial works as the volume
control. So you do not have to select VOL to adjust the volume level. *4 Depending on the amplifier gain control setting. (See page 38 for details.)
Select the item you want to adjust.
Each time you press the button, the adjustable items change as follows:

For KD-G801:

Adjust the setting.
To increase the level or turn on the loudness To decrease the level or turn off the loudness

(fader)

(balance)

(loudness)

(volume)

For KD-G701:

WOOFER

(subwoofer)

Indication pattern changes as you adjust the fader or balance.

Indication FAD*

To do:
Range Ex. 1: When you adjust FAD (fader) LOUD indicator

LOW LEVEL

MID LEVEL

HI LEVEL

FREQ (LOW, HI): Select the center frequency to adjust. WIDTH (LOW, MID): Select the band width level.
Adjust the selected sound element.
The last selected sound mode is called up. Indication LEVEL LOW
Preset values MID HI 06 (min.) 06 (min.) 06 (min.) | | | +06 (max.) +06 (max.) +06 (max.) 60Hz 80Hz 100Hz 120Hz 1 (min.) | 4 (max.) 1 (min.) | 2 (max.) 8kHz 10kHz 12kHz 15kHz
Select the sound mode you want to adjust.
Ex.: When you select JAZZ
Repeat steps 4 and 5 to adjust the other sound elements. Select one of the user sound modes (USER 1, USER 2, USER 3).
Select sound elements to adjust.
Each time you press the button, the sound elements change as follows:
LOW LEVEL* = LOW FREQ = LOW WIDTH = MID LEVEL* = MID WIDTH = HI (high) LEVEL* = HI (high) FREQ = (back to the beginning)
Press EQ to store the adjustments.
MEMORY appears for a while.
Storing your own sound adjustments
LEVEL (LOW, MID, HI): Adjust the enhancement level.

OTHER MAIN FUNCTIONS

Changing the general settings (PSM)
You can change the items listed in the table below and on page 35 by using the PSM (Preferred Setting Mode) control.
Adjust the PSM item selected.

Basic Procedure

Press and hold SEL (select) for more than 2 seconds so that one of the PSM items appears on the display. (See below and page 35.)
Repeat steps 2 and 3 to adjust the other PSM items if necessary. Finish the setting.
Select the PSM item you want to adjust.
Preferred Setting Mode (PSM) items
For detailed operations of each PSM items, refer to the pages listed in the table.

Indications

DEMO MODE CLOCK HOUR CLOCK MINUTE CLOCK24H/12H AUTO ADJUST CLOCK DISP AF-REG Display demonstration Hour adjustment Minute adjustment 24/12-hour time display Automatic clock setting Clock display Alternative frequency/ Regionalization reception

Selectable values/items

DEMO OFF DEMO ON
Factory-preset See settings page
DEMO ON 0 (0:00) 00 (0:00) CLOCK 24HOUR ADJUST ON CLK DISP ON 9 8
(1 12) CLOCK 12HOUR CLOCK 24HOUR ADJUST OFF CLK DISP OFF AF ON ADJUST ON CLK DISP ON AF REG AF OFF*1

14, 15

*1 Only for KD-G801: Displayed only when the DAB AF is set to OFF. 34

To select the telephone muting TELEPHONE
To select the scroll modeSCROLL MODE
To select the external component to use EXTERNAL IN (only for KD-G801)
You can connect the external component to the CD changer jack on the rear using the Line Input Adapter KS-U57 (not supplied). To use the external component as the playback source through this unit, you need to select which componentCD changer or external componentto use. When shipped from the factory, CD changer is selected as the external component. CHANGER: To use the CD changer. LINE IN: To use the external component other than CD changer.
To select the amplifier gain control AMP.GAIN
You can change the maximum volume level of this unit. When the maximum power of the speakers is less than 50 W, select LOW POWER to prevent them from being damaged. When shipped from the factory, HIGH POWER is selected. LOW POWER: You can adjust the volume level from VOL 00 to VOL 30.
Note: For connecting the Line Input Adapter KS-U57 and the external component, refer to the Installation/ Connection Manual (separate volume).
Note: If you change the setting from HIGH POWER to LOW POWER while listening at a volume level more than 30, the unit automatically changes the volume level to VOL 30.
HIGH POWER: You can adjust the volume level from VOL 00 to VOL 50.
To turn the tag display on or off TAG DISPLAY
An MP3/WMA file can contain file information called ID3 Tag where its album name, performer, track title, etc. are recorded. There are two versionsID3v1 (ID3 Tag version 1) and ID3v2 (ID3 Tag version 2). If both ID3v1 and ID3v2 are recorded on a disc, ID3v2 information will be shown. When shipped from the factory, TAG DISP ON is selected. TAG DISP ON: Turns on the ID3 tag display while playing MP3/WMA files. If an MP3/WMA file does not have ID3 tags, folder name and file name appear.
To turn the slot light on or off SLOT LIGHT
You can turn off the slot light if you do not want the illumination each time you insert/eject the disc or when you change the control panel angle. When shipped from the factory, slot light is activated. ON: Activates the illumination. OFF: Deactivates the illumination.
Note (only for KD-G801): If you change the setting from TAG DISP OFF to TAG DISP ON while playing an MP3/WMA file, the tag display will be activated when the next file starts playing.
TAG DISP OFF: Turns off the ID3 tag display while playing MP3/WMA files. (Only the folder name and file name can be shown.)
You can assign names to CDs (both in this unit and in the CD changeronly for KD-G801). After assigning a name, it will appears on the display when you select the source. Source CDs* Maximum number of characters Up to 32 characters (up to 40 discs)
About the available characters, see page 52.
Move the cursor to the next (or previous) character position.
* You cannot assign a name to a CD Text or an

To go to the next or previous tracks/files
Press briefly during play, to skip ahead to the beginning of the next track/file. Each time you press the button consecutively, the beginning of the next tracks/ files is located and played back. Press 4 briefly during play, to skip back to the beginning of the current track/file. Each time you press the button consecutively, the beginning of the previous tracks/files is located and played back.
Note: Folder name appears on the display instead of ROOT, if an MP3 disc contains a folder.
To go to a particular disc directly
This operation is only possible when using JVC MP3-compatible CD changer (CH-X1500).
To skip to the next or previous folder (only for MP3 discs)
Press 5 (up) while playing an MP3 disc, to go to the next folder. Each time you press the button consecutively, the next folder is located, and the first file in the folder starts playback. Press (down) while playing an MP3 disc, to go to the previous folder. Each time you press the button consecutively, the previous folder is located, and the first file in the folder starts playback.
To go to a track/file quickly (+10 and 10 buttons) 1 Press MODE to enter the functions mode
To skip 10 tracks/files* forwards to the last track/file To skip 10 tracks/files* backwards to the first track/file * First time you press +10 or 10 button, the track/file skips to the nearest higher or lower track/file with a track/file number of multiple ten (ex. 10th, 20th, 30th). Then each time you press the button, you can skip 10 tracks/files (see How to use the +10 and 10 buttons below). After the last track/file, the first track/file will be selected, and vice versa.
To show the disc information for CD Text and MP3 discs
This is possible only when connecting a JVC CD changer equipped with CD Text and/or MP3 disc information reading capability.
Select text display mode while playing a CD Text or an MP3 disc.
Note: If the current playing disc is an MP3 disc, files are skipped within the same folder.
How to use the +10 and 10 buttons Ex. 1: To select track/file number 32 while playing track/file number 6
For details, see page 24 about CD Text disc information and page 27 about MP3 disc information.

Track/file 6

(Three times) \ 10 \ 20 \ 30

Ex. 2: To select track/file number 8 while playing track/file number 36

Track/file 36

(Three times) \ 30 \ 20 \ 10
To play back tracks/files at random (Folder Random/Disc Random/Magazine Random Play)

FLDR RND*

and RND All files of the indicators current folder, then light up. files of the next folder and so on. and RND All tracks/files of the indicators current (or specified) light up. disc. RND indicator All tracks/files of the lights up. inserted discs.
MODE is still on the display. Each time you press the button, the random play mode changes as follows: For MP3 discs:

MAG RND

* FLDR RND is only applicable for MP3 disc.

FLDR RND Canceled

For CDs:

DISC RND MAG RND

To play back tracks/files repeatedly (Track Repeat/Folder Repeat/Disc Repeat Play)
MODE is still on the display. Each time you press the button, the repeat play mode changes as follows: For MP3 discs:
RND indicator Ex.: When you select MAG RND

TRK RPT Canceled

FLDR RPT DISC RPT

DISC RPT

Note: MP3 indicator also lights up if the current playing disc is an MP3 disc.
(disc) and RPT indicators Ex.: When you select DISC RPT

Active indicator

Plays at random

Mode TRK RPT FLDR RPT*

Plays repeatedly
RPT indicator The current (or lights up. specified) track/file. and RPT indicators light up. All files of the current (or specified) folder of the current disc.
INT indicator Ex.: When you select TRK INT
and RPT All tracks/files of the indicators current (or specified) light up. disc.
Mode TRK INT Active indicator Plays the beginnings (15 seconds) of
* FLDR RPT is only applicable for MP3 disc.
INT indicator All tracks/files of the lights up. current disc. and INT indicators light up. and INT indicators light up. The first file of every folder of the current disc. The first tracks/files of the inserted discs.
To play back only intros (Track Intro Scan/Folder Intro Scan/Disc Intro Scan)

FLDR INT*

DISC INT
is still on the display. Each time you press the button, the intro scan mode changes as follows: For MP3 discs:
* FLDR INT is only applicable for MP3 disc.

Storing DAB services in memory
You can preset up to 6 DAB services in each DAB band (DAB1, DAB2, and DAB3) manually. Before you start. Press FM/AM DAB briefly if CD, CD changer, or external component is the current source.
To change the display information while tuning in to an ensemble
Normally service name is shown on the display. If you want to check the ensemble name or its frequency, press DISP (display) repeatedly. Each time you press the button, the following information appears for a while on the display.
Service name Ensemble name Channel number Frequency
Select the DAB band (DAB1, DAB2, or DAB3) you want.
Start searching for an ensemble.
To tune in to a particular ensemble without searching
Tune in to an ensemble you want.
Tuning in to a preset DAB service
You can easily tune in to a preset DAB service. Remember that you must store services first. If you have not stored them yet, see Storing DAB services in memory on pages 49 and 50. Before you start. Press FM/AM DAB briefly if CD, CD changer, or external component is the current source.
Select a service of the ensemble you want to listen to.
To select the next service To select the previous service
Press and hold the number button (in this example, 1) for more than 2 seconds to store the selected service into the preset number you want.

Selected preset number

Repeat the above procedure to store other DAB services into other preset numbers.
Select the number (1 6) for the preset DAB service (primary) you want.
Notes: You can only preset primary DAB services. If you store a secondary service, its primary service will be stored instead. A previously preset DAB service is erased when a new DAB service is stored in the same preset number. Preset DAB services are erased when the power supply to the memory circuit is interrupted (for example, during battery replacement). If this occurs, preset the DAB services again.
Note: If the selected primary service has some secondary services, pressing the same number button repeatedly will tune in to the secondary services.

Tracing the same programme automatically (Alternative Reception)
You can keep listening to the same programme. While receiving a DAB service: When driving in an area where a service cannot be received, this unit automatically tunes in to another ensemble or FM RDS station, broadcasting the same programme. While receiving an FM RDS station: When driving in an area where a DAB service is broadcasting the same programme as the FM RDS station is broadcasting, this unit automatically tunes in to the DAB service.
You can adjust the volume level of DAB tuner and store it in memory. By adjusting the volume level properly to match it to the FM sound level, you will not need to adjust the volume level each time you change the source to DAB. When shipped from the factory, DAB volume level is set at VOL 00. See also Changing the general settings (PSM) on pages 34 and 35.
2 seconds so that one of the PSM items appears on the display. 2 Press or 4 to select DAB VOL (volume). 3 Turn the control dial to set to the desired volume. You can set it from VOL 12 to VOL +12. 4 Press SEL (select) to finish the setting.
To use Alternative Reception
When shipped from the factory, Alternative Reception is activated. See also Changing the general settings (PSM) on pages 34 and 35.
2 seconds so that one of the PSM items appears on the display. 2 Press or 4 to select DAB AF (alternative frequency). 3 Turn the control dial to select the desired mode. AF ON: Traces the programme among DAB services and FM RDS stationsAlternative Reception. The AF indicator lights up on the display (see page 14). AF OFF: Alternative Reception is deactivated. 4 Press SEL (select) to finish the setting.
Note: When Alternative Reception (for DAB services) is activated, Network-Tracking Reception (for RDS stations: see page 14) is also activated automatically. On the other hand, Network-Tracking Reception cannot be deactivated without deactivating Alternative Reception.
What you can do more with DAB
To adjust the DAB volume level

ADDITIONAL INFORMATION

Sound modes (preset frequency level settings)
The list below shows the preset frequency level settings for each sound mode. Preset equalizing values LOW MID MID WIDTH LEVEL WIDTH 1 +1 ++00 1
Sound modes FLAT HARD ROCK R&B POP JAZZ DANCE MUSIC COUNTRY REGGAE CLASSIC USER 1 USER 2 USER 3
LOW LEVEL 00 +03 +03 +02 +03 +04 +02 +03 +00 00
LOW FREQ 60Hz 120Hz 80Hz 120Hz 80Hz 60Hz 60Hz 60Hz 80Hz 60Hz 60Hz 60Hz
HI LEVEL 00 +02 +03 +02 +03 +01 +02 +02 +00 00
HI FREQ 8kHz 8kHz 15kHz 10kHz 10kHz 8kHz 12kHz 12kHz 10kHz 8kHz 8kHz 8kHz

Available characters

In addition to the alphabets (A Z, a z), you can use the following characters to assign names to CDs and CD changeronly for KD-G801. (See page 39.) These characters can be also used to show other information such as disc title/performer, RDS, and DAB on the display.

Accented letters

Upper case Lower case

Numbers and symbols

EN52-57_G801_G701[E_EX]f.p65

TROUBLESHOOTING

Symptoms
Sound cannot be heard from the speakers.

Causes

The volume level is set to the minimum level. Connections are incorrect.

Remedies

Adjust it to the optimum level. Check the cords and connections. Press the reset button on the control panel. (Your preset adjustments will also be erased.) (See page 2.) Press the reset button on the control panel. (See page 2.) If the reset button does not work, check the Installation/ Connection Manual (separate volume). (Ex.: You have used a longer screw than specified.) Store stations manually.

General

This unit does not work at all.
The built-in microcomputer may have functioned incorrectly due to noise, etc. There is something blocking the control movement.
When PUSH RESET appears on the display.
SSM (Strong-station Sequential Memory) automatic preset does not work. Static noise while listening to the radio. Disc cannot be played back. CD-R/CD-RW cannot be played back. Tracks on the CD-R/ CD-RW cannot be skipped. Disc cannot be ejected.

Signals are too weak.

The aerial is not connected firmly. Disc is inserted upside down. CD-R/CD-RW is not finalized.
Connect the aerial firmly. Insert the disc correctly. Insert a finalized CD-R/ CD-RW. Finalize the CD-R/CD-RW with the component which you used for recording. Unlock the disc. (See page 24.) Stop playback while driving on rough roads. Change the disc. Check the cords and connections. Insert a disc into the loading slot. Insert the disc correctly. While pressing CD/CD-CH (for KD-G801) or CD (for KD-G701), press and hold SEL (select) for more than 2 seconds to eject the disc.
Disc is locked. You are driving on rough roads. Disc is scratched. Connections are incorrect.

Disc Playback

Disc sound is sometimes interrupted.
Disc cannot be recognized (NO DISC appears on the display).
No disc in the loading slot. Disc is inserted incorrectly. The unit may have functioned incorrectly.
What appears to be trouble is not always serious. Check the following points before calling a service center.
Disc cannot be played back.
No MP3/WMA files are recorded on the disc. MP3/WMA files do not have the extension code <.mp3> or <.wma> in their file names. MP3/WMA files are not recorded in the format compliant with ISO 9660 Level 1, Level 2, Romeo, or Joliet.