FITTING INSTRUCTIONS FOR CP0023BL/WH CRASH PROTECTORS KAWASAKI ZX9R C1/C2/E1/E2
PLEASE NOTE THAT THE WAY THE KIT IS PACKED DOES NOT NECESSARILY REPRESENT THE WAY OF MOUNTING TO THE BIKE
Please note that in cases where kits are packed with rubber washers holding the components onto the bolt the rubber washers should be thrown away! Nearside (left side as you sit on bike) Remove fairing panel Remove water bottle Fit R&G water bottle, refill Remove engine bolt, Insert M10 x 120-mm long bolt into engine mount. Wind bolt in so that the fairing can be fitted correctly and the bolt head touches the inside of the fairing. Paint end of bolt with white paint/Tippex Refit panel (bolt should leave mark on inside of panel) Remove panel and pilot drill Refit panel and check hole in correct position Remove panel and drill 28 mm diameter hole (tank cutter/cone cutter) Use sharp knife to deburr hole Remove engine bolt completely. Refit fairing Screw 180mm tie bar into engine (use original nut - advise holding nut square to stop cross threading.) Fit nearside spacer (20mm diameter), slide washer over bar up to spacer. Fit crash protector Lock in place with R&G-supplied nyloc nut Tighten bolt until you feel some compression from inside the protector. Turn a little more so that you feel the compression increase slightly. Then apply a quarter turn. Do not overtighten as damage can occur to the bike. Do not exceed 40nm of torque. Repeat for offside, except no water bottle, a larger diameter (25mm) spacer and a 165mm bar NOTE for some E models the 150mm bar and the castellated spacer needs to be used
R&G Racing Unit 5K, Blacknest Industrial Park, Blacknest Road, Alton, Hampshire, GU34 4PX Tel: +44 (0)6380 Fax: +44 (0)www.rg-racing.com Email: info@rg-racing.com

CONSUMER NOTICE

The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design changes which do not diminish their performance or visual appeal and supplying them in such state shall conform to the order. The Buyer acknowledges no representation or warranty (other than as to title) has been given or will apply to the Products other than those in R&Gs order or confirmation and the Buyer confirms it has chosen the Products as being of merchantable quality and suitable for its particular purposes. Where R&G fits the Products or undertakes other services it shall exercise reasonable skill and care and rectify any fault free of charge unless the workmanship has been disturbed. The Buyer is responsible for ensuring that the warranty on the motorcycle is not affected by the fitting of the Products. On return of any defective Products R&G shall at its option either supply a replacement or refund the purchase money but shall not be liable if the Products have been modified or used or maintained otherwise than in accordance with R&Gs or manufacturers instructions and good engineering practice or if the defect arises from accident or neglect. Other than identified above and subject to R&G not limiting its liability for causing death and personal injury, it shall not be liable for indirect or consequential loss and otherwise its liability shall be limited to the amounts paid by the Buyer for the Products or the fitting or service concerned. These terms do not affect the Buyers statutory rights.
R&G RACING RETURNS POLICY (NON-FAULTY GOODS)
Returns must be pre-authorised (if not pre-authorised the return will be rejected) Goods may only be returned direct to us if they were purchased direct from us (customer must prove if necessary). Otherwise to be returned to original vendor. Goods must be in re-sellable condition, in the opinion of R&G Racing. All returns are subject to a 25% restocking and handling fee (25% of the gross value exc. P&P at the prevailing price at time of purchase). The customer must pay any and all carriage charges. No returns of discontinued products, unless within 14 days of purchase. This policy does not affect your statutory rights and does not refer to faulty goods.

Aluminium Kits & Accessories Part Numbers & Prices
SK3 SK4 SK5 SK6 SK7 SK8 SK9 SK10 SKDUC7 SKDUC8 SKDUC9 SKDUC10 SKDUC14 TBMW TCAG TDUC THO089 THON TKAW TKTM TMOT TOAP TSUZ TTRI TYAM LOFCD10 LOFCH10 LOFCH20 LOFCK10 LOFCK20 LOFCK30 LOFCS10 LOFCY10 LOFCY20 LOFCY30 LTYOKE10 LTYOKE20 LTYOKE30 LTYOKE40 LTYOKE50 LTYOKE50 LTYOKE50 LTYOKE100 YOKECAP10 RESR10 RESR20 RESO20-CS445 RESR30 RESR10 RESR50 RESR60 RESR70 RESR80 RESR90 RESO10 RESO20 RESO30 RESO40 RESO50 RESO60 RESO70 BARENDAP10 BARENDAP20 BARENDAP30 BARENDHO10 BARENDHO20 Added MaBARENDHO30 BARENDKA10 BARENDKA20 BARENDKA30 BARENDKA40 BARENDSU10 BARENDSU20 BARENDSU30 BARENDSU40 BARENDSU50 BARENDSU60 BARENDYA10 BARENDYA20 UBARENDS10

Description

Screen Kits 2 Screen Bolt Kit with Nylon Nuts & Washers Screen Bolt Kit with Nylon Nuts & Washers 5 Screen Bolt Kit with Nylon Nuts & Washers Screen Bolt Kit with Nylon Nuts & Washers Screen Bolt Kit with Nylon Nuts & Washers 8 Screen Bolt Kit with Nylon Nuts & Washers 9 Screen Bolt Kit with Nylon Nuts & Washers 10 Screen Bolt Kit with Nylon Nuts & Washers Screen Bolt Kit comprising 4mm Bolts, Nuts & Washers 8 Screen Bolt Kit comprising 4mm Bolts, Nuts & Washers 9 Screen Bolt Kit comprising 4mm Bolts, Nuts & Washers 10 Screen Bolt Kit comprising 4mm Bolts, Nuts & Washers 14 Bolt Ducati Side Panel kit comprising 4mm Bolts, Nuts & Washers Tank (Fuel Cap) Kits All BMW Fuel Cap Kits All Cagiva Fuel Cap Kits All Ducati Fuel Cap Kits All Honda Fuel Cap Kits All Honda Fuel Cap Kits All Kawasaki Fuel Cap Kits All KTM Fuel Cap Kits All Moto Guzzi Fuel Cap Kits All Aprilia Fuel Cap Kits All Suzuki Fuel Cap Kits All Triumph Fuel Cap Kits All Yamaha Fuel Cap Kits Oil Filler Caps - each Ducati & Some Aprilia Honda Standard Honda BlackBird/VFR Etc Kawasaki Standard - M30 x 1.50mm pitch Kawassaki ZX7R - M20mm x 2.00mm pitch Kawasaki ZX9R (98) - M38mm x 1.50mm pitch Suzuki & Some Aprilia Yamaha Standard Yamaha XJR1300 Yamaha R1 (2004+) Yoke Nut - Centre of Yokes & Caps Honda Yoke Nut - Centre of Yoke Kawasaki Yoke Nut - Centre of Yoke Suzuki Late GSXR Yoke Nut - Centre of Yoke Suz/Triumph/Yamaha Yoke Nut - Centre of Yoke Suzuki Bandit/Other Yoke Nut - Centre of Yoke Yamaha Fazer/TDM/Other Yoke Nut - Centre of Yoke Kawasaki ZX6r (01) Other Yoke Nut - Centre of Yoke Triumph T595/955 Yoke Nut - Centre of Yoke Various Models - Yoke Caps for Forks - Pair Reservoir Caps - each Threaded Round Cap - 61mm o/d 2 Screws Round Cap - 56mm o/d 2 Screws Round Cap - 56mm o/d - with 45mm length bolts Threaded Round Cap - 38mm o/d Threaded Round Cap - 59mm o/d Threaded Round Cap - 42mm o/d Threaded Round Cap - 53mm o/d Ducati/Aprilia Threaded Round Cap - 39mm o/d Ducati/Aprilia Threaded Round Cap - 56mm o/d Threaded Round Cap - 48mm o/d Oblong 43 x 75mm Oblong 37 x 55mm Oblong 43 x 85mm Oblong 47 x 69mm Oblong 57 x 33mm Triangle for Clutch on Ducati 749/999 Triangle for Brake on Ducati 749/999 Bar Ends - Pair Pairof Aprilia Bar Ends - RSV Millie etc Pairof Aprilia Bar Ends - RS125 / Pegaso Pairof Aprilia Bar Ends - RSV/Factory/Tuono Pair of Honda Bar Ends - CBR600 / CBR900 etc Pair of Honda Bar Ends - SP1/SP2 -06 Hornet Pair of Honda Bar Ends - 07+ Hornet Pair of Kawasaki Bar Ends - ZX6 / ZX9 Pair of Kawasaki Bar Ends - ZX7 / ZX12 Pair of Kawasaki Bar Ends - GPZ / Z1000 / ZZR Pair of Kawasaki Bar Ends - ZX10R (2006) Pair of Suzuki Bar Ends - GSXR600 K1 / K2 Pair of Suzuki Bar Ends - SV650 / GSXR750 / SRAD / GSXR1100 - etc Pair of Suzuki Bar Ends - SV650 / SV1000 / TL1000 etc Pair of Suzuki Bar Ends - GSXR1300 etc Pair of Suzuki Bar Ends - GSXR600 etc Pair of Suzuki Bar Ends - GSXR1000 K6/Other Pair of Yamaha Bar Ends - R1 etc Pair of Yamaha Bar Ends - R6 etc Bar Ends - Pair for Hollow Bars

Retail Net

2,54 4,25 5,10 5,95 6,80 7,65 8,50 9,35 8,50 10,20 11,06 12,76 17,86 4,65 4,67 3,40 10,63 10,63 5,52 4,67 3,40 4,67 5,52 4,67 4,67 9,35 9,35 9,35 9,35 9,35 9,35 9,35 9,35 9,35 9,35 9,35 9,35 9,35 9,35 9,35 9,35 9,35 12,76 17,01 17,01 17,01 17,01 13,61 17,01 13,61 17,01 13,61 13,61 13,61 17,01 13,61 17,01 17,01 13,61 21,27 21,27 12,76 13,61 13,61 13,61 13,61 13,61 14,46 13,61 13,61 13,61 13,61 15,31 13,61 13,61 13,61 14,46 12,76 12,76 8,50
PLOAD14 PLOAD14-T PLOAD17 PLOAD19 PLOAD22 PLOAD1814 PLOAD2017 LQRCLIP14 LQRCLIP17 LQRCLIP19 LQRCLIP24 QRCLIP1014 QRCLIP1017 QRCLIP1019 QRCLIP1024 QRPACKRIVET14 QRPACKRIVET17 QRPACKRIVET19 QRPACKRIVET24 QRPACKSLIDE14 QRPACKSLIDE17 QRPACKSLIDE19 QRPACKSLIDE24 LQRCLIPAK14 LQRCLIPAK17 LQRCLIPAK19 LQRCLIPAK21 LQRCLIPAK24 QRCLIPAK1014 QRCLIPAK1017 QRCLIPAK1019 QRCLIPAK1024 QRPACKAKRIVET14 QRPACKAKRIVET17 QRPACKAKRIVET19 QRPACKAKRIVET24 QRPACKAKSLIDE14 QRPACKAKSLIDE17 QRPACKAKSLIDE19 QRPACKAKSLIDE24 LDZUS-PANEX10 QRSTEEL17SETBK BOB6 BOB8 BOB10 BOB12 SPN10 SPN12 LCA10 LCA20 LDA10 LDA20 LDA30 LGRODF66145 LGRODF66146 LGRODF66150 LGRODF66154 LGRODF66162 LGRODF66170 Added MaLGRODF66176 LGRODF66180 LGRODF66184 LGRODF66210 LGRODF66214 LGRODF66255 LGRODF66272 LGRODF66284 LGRODF68214 LGRODF68240 LGRODM66140 LGRODM66149 LGRODM66163 LGRODM66174 LGRODM66180 LGRODM66188 LGRODM66195 LGRODM66197 LGRODM66220 LGRODM66224

Screen Kits Pre-Load Adjusters (Pair) Pre-Load 14mm Pre-Load 14mm - Thinner Fork Tops Pre-Load 17mm Pre-Load 19mm Pre-Load 22mm Pre-Load 18/14mm Pre-Load 20/17mm Alloy Quick Release Fasteners 14mm Individual D-Ring Quick Release Fastener 17mm Individual D-Ring Quick Release Fastener 19mm Individual D-Ring Quick Release Fastener 24mm Individual D-Ring Quick Release Fastener Packs of 10 - D-Ring 14mm Quick Release Fasteners Packs of 10 - D-Ring 17mm Quick Release Fasteners Packs of 10 - D-Ring 19mm Quick Release Fasteners Packs of 10 - D-Ring 24mm Quick Release Fasteners Pack of 10 - D-Ring 14mm Quick Release Fastners & Rivet on Recepticles & Rivets Pack of 10 - D-Ring 17mm Quick Release Fastners & Rivet on Recepticles & Rivets Pack of 10 - D-Ring 19mm Quick Release Fastners & Rivet on Recepticles & Rivets Pack of 10 - D-Ring 24mm Quick Release Fastners & Rivet on Recepticles & Rivets Pack 10 - D-Ring 14mm Quick Release Fasteners & Slip on Recepticals Pack 10 - D-Ring 17mm Quick Releas+D110e Fasteners & Slip on Recepticals Pack 10 - D-Ring 19mm Quick Release Fasteners & Slip on Recepticals Pack 10 - D-Ring 24mm Quick Release Fasteners & Slip on Recepticals 14mm Individual Allen Key Quick Release Fastener 17mm Individual Allen Key Quick Release Fastener 19mm Individual Allen Key Quick Release Fastener 21mm Individual Allen Key Quick Release Fastener 24mm Individual Allen Key Quick Release Fastener Packs of 10 - Allen Key 14mm Quick Release Fasteners Packs of 10 - Allen Key 17mm Quick Release Fasteners Packs of 10 - Allen Key 19mm Quick Release Fasteners Packs of 10 - Allen Key 24mm Quick Release Fasteners Pack of 10 - Allen Key 14mm Quick Release Fastners & Rivet on Recepticles & Rivets Pack of 10 - Allen Key 17mm Quick Release Fastners & Rivet on Recepticles & Rivets Pack of 10 - Allen Key 19mm Quick Release Fastners & Rivet on Recepticles & Rivets Pack of 10 - Allen Key 24mm Quick Release Fastners & Rivet on Recepticles & Rivets Pack 10 - Allen Key 14mm Quick Release Fasteners & Slip on Recepticals Pack 10 - Allen Key 17mm Quick Releas+D110e Fasteners & Slip on Recepticals Pack 10 - Allen Key 19mm Quick Release Fasteners & Slip on Recepticals Pack 10 - Allen Key 24mm Quick Release Fasteners & Slip on Recepticals Black Zinc Steel Quick Release Fasteners Individual Black Zinc Coated Steel D-Ring Quick Release Fastener Pack of 10 Black Steel 17mm Fasteners, Rivet on Backs and Rivets Paddock Stand Bobbins / Swing Arm Spools Pair of M6 Paddock Stand Bobbins Pair of M8 Paddock Stand Bobbins Pair of M10 Paddock Stand Bobbins Pair of M12 Paddock Stand Bobbins Sprocket Nuts - 6 pack 10mm Sprocket Nuts 12mm Sprocket Nuts Cable & Dial Adjusters Standard Cable Adjuster (2 Piece) Suzuki / Other Cable Adjuster (1 Piece) 4 Position Dial Adjuster Honda/Kawasaki Dial Adjuster on Lever - Spin Type 5 Position Dial Adjuster Gear Shift Rods Gear Shift Rod Female - 6mm Thread/6mm Thread - 145mm Overall Length Gear Shift Rod Female - 6mm Thread/6mm Thread - 146mm Overall Length Gear Shift Rod Female - 6mm Thread/6mm Thread - 150mm Overall Length Gear Shift Rod Female - 6mm Thread/6mm Thread - 154mm Overall Length Gear Shift Rod Female - 6mm Thread/6mm Thread - 162mm Overall Length Gear Shift Rod Female - 6mm Thread/6mm Thread - 170mm Overall Length Gear Shift Rod Female - 6mm Thread/6mm Thread - 176mm Overall Length Gear Shift Rod Female - 6mm Thread/6mm Thread - 180mm Overall Length Gear Shift Rod Female - 6mm Thread/6mm Thread - 184mm Overall Length Gear Shift Rod Female - 6mm Thread/6mm Thread - 210mm Overall Length Gear Shift Rod Female - 6mm Thread/6mm Thread - 214mm Overall Length Gear Shift Rod Female - 6mm Thread/6mm Thread - 255mm Overall Length Gear Shift Rod Female - 6mm Thread/6mm Thread - 272mm Overall Length Gear Shift Rod Female - 6mm Thread/6mm Thread - 284mm Overall Length Gear Shift Rod Female - 6mm Thread/8mm Thread - 214mm Overall Length Gear Shift Rod Female - 6mm Thread/8mm Thread - 240mm Overall Length Gear Shift Rod Male - 6mm Thread/6mm Thread - 140mm Overall Length Gear Shift Rod Male - 6mm Thread/6mm Thread - 149mm Overall Length Gear Shift Rod Male - 6mm Thread/6mm Thread - 163mm Overall Length Gear Shift Rod Male - 6mm Thread/6mm Thread - 174mm Overall Length Gear Shift Rod Male - 6mm Thread/6mm Thread - 180mm Overall Length Gear Shift Rod Male - 6mm Thread/6mm Thread - 188mm Overall Length Gear Shift Rod Male - 6mm Thread/6mm Thread - 195mm Overall Length Gear Shift Rod Male - 6mm Thread/6mm Thread - 197mm Overall Length Gear Shift Rod Male - 6mm Thread/6mm Thread - 220mm Overall Length Gear Shift Rod Male - 6mm Thread/6mm Thread - 224mm Overall Length

25,52 25,52 25,52 25,52 25,52 25,52 25,52 2,54 2,54 2,54 2,54 25,52 25,52 25,52 25,52 32,33 32,33 32,33 32,33 32,33 32,33 32,33 32,33 2,54 2,54 2,54 2,54 2,54 25,52 25,52 25,52 25,52 32,33 32,33 32,33 32,33 32,33 32,33 32,33 32,33 1,69 23,82 10,85 11,02 12,55 16,16 13,61 13,61 4,68 4,68 4,68 2,98 4,68 13,61 13,61 15,31 13,61 13,61 13,61 15,31 15,31 13,61 15,31 17,01 21,27 21,27 21,27 18,71 21,27 9,35 10,20 11,06 15,31 15,31 13,61 15,31 15,31 17,01 17,01
CABPRA10 CABPRA20 CABPRH10 CABPRH20 CABPRH30 CABPRH40 CABPRK10 CABPRK20 CABPRK30 CABPRK40 CABPRK40 CABPRS10 CABPRS20 CABPRY10 CABPRY20 CABPRY40 CABPRY50 CABPRY60 CABSETA10 CABSETA20 CABSETH10 CABSETH20 CABSETH30 CABSETH40 CABSETK10 CABSETK20 CABSETK30 CABSETS10 CABSETS20 CABSETY10 CABSETY20 CABSETY40 CABSETY50 CABSETY60 FPLUGDUC10 FPLUGDUC30 FPLUGDUC30PR FPLUGKAW10 FPLUGSUZ10 FPLUGYAM10 FPLUGYAM20 STPLUGR1 SPYAM10-8 DUCAXLESET SKDUC9 SKDUC14 LDUCNUT40 SITEM1 SITEM1FULL8 SITEM3 SITEM13FULL WSKIT25 WSKIT50 PBTUBFAIR PBTUBALLEN PBTUBMIXED PBTUBWAD PBTUBNUTS PBTUBCOLLAR WSBOX200 PBCAB500 Added AuRESCLIP10 2DCAP10 4DCAP10 BNCOVER7-2 BNCOVER7-3 HOSESEP10 MUDHUG MUDHUG20 NPLATE NPLATEUSA PCLIP10 PB308 / PB310 / PB330 PB410 / PB435 PB508 / PB510 etc PB610 / PB612 etc PB825 / PB830 etc
Screen Specific Fitment Pages Chain Adjuster Blocks - SeeKits Aprilia RSV (98-03) Falco, Tuono Pair of Blocks Aprilia RSV/R (2004+) Pair of Blocks Honda CBR900RR (00-03) Pair of Blocks Honda SP1/SP2 Pair of Blocks Honda CB1300 Pair of Blocks Honda CBR600RR / CBR1000 Pair of Blocks Kawasaki ZX6/ZX7/ZX9/ZX12 Pair of Blocks Kawasaki ZX10R (2004-2005) Pair of Blocks Kawasaki ZX9R C1/C2 Pair of Blocks Kawasaki ZX10R '06+ Pair of Blocks Kawasaki ZX10R '06+ Pair of Blocks, & Bolt & Nut Set Suzuki GSXR600/750/1000/TL1000/GSXR1300 Pair of Blocks Suzuki 600/1200 Bandit Pair of Blocks Yamana R6 (98-02) / R1(98-03) Pair of Blocks Yamaha R6 (03+) / R1 Pair of Blocks Yamaha R1 (04+) / R1 Pair of Blocks Yamaha XJR1200/1300 Pair of Blocks Yamaha XJR1300SP Pair of Blocks Aprilia RSV (98-03) Falco, Tuono Block & Bolt & Nut Set Aprilia RSV/R (2004+) Block & Bolt & Nut Set Honda CBR900RR (00-03) Block & Bolt & Nut Set Honda SP1/SP2 Block & Bolt & Nut Set Honda CB1300 Block & Bolt & Nut Set Honda CBR600RR / CBR1000 Block & Bolt & Nut Set Kawasaki ZX6/ZX7/ZX9/ZX12 Blocks, Bolt & Nut Set Kawasaki ZX10R (2004-2005) Blocks, Bolts & Nut Set Kawasaki ZX9R C1/C2 Blocks, Bolt & Nut Set Suzuki GSXR600/750/1000/TL1000/GSXR1300 Block & Bolt & Nut Set Suzuki 600/1200 Bandit Block & Bolt & Nut Set Yamaha R6 (98-02) / R1(98-03) Block & Bolt & Nut Set Yamaha R6 (03+) / R1 Block, Bolt & Nut Set Yamaha R1 (04+) / R1 Block & Bolt & Nut Set Yamaha XJR1200/1300 Block & Bolt & Nut Set Yamaha XJR1300SP Block & Bolt & Nut Set Frame Plugs Ducati 748/916/996 Frame p g - Set of 5 plugs Ducati 749/999 Full Set of Frame Plugs Ducati 749/999 Pair of Lower Plugs, Rod, Bolt & Grub Screw Kawasaki ZRX1100/ZRX1200 Frame Plugs - Pair Suzuki 600/1200 Bandit (2001+) Frame Plugs - Pair Yamaha R1 (1999-2003) Frame Plugs - Pair Fazer 1000, XJR1200/XJR1300 -Frame Plugs - Pair Yamaha Specials R6 / R1 / Blade Stem Plug Set of 8 Yamaha Fazer/Other Top Cam Bolts Ducati 748 / 916 / 996 Special Items Full set of 3 Axle Nuts 9 Bolt M4x12mm Screen Kit 14 Bolt M4x12mm Side Fairing Kit Ducati 1098 Special Items Front Spindle Collar Suzuki Specials Top Of Rocker Cover - each Top Of Rocker Cover - Set of 8 Side Of Rocker Cover (Plain) - each Complete Set 8 Top & 4 Side (Plain) Tubs & Workshop Kits 25 Piece Workshop Kit - Bolts, Nuts & Washers 50 Piece Workshop Kit - Bolts, Nuts & Washers 100 Pc Metric Dome Head Allen Key Bolt Tub 100 Pc Metric Socket Cap Allen Key Bolt Tub 100 Pc Metric Assorted Allen Key Bolt Tub 100 Pc Drilled Washer Tub - M5 - Mpc Nut & Washer Tub 100 pc Threaded Collar Tub - M5, M6 - Various o/d's & Lengths 200 Piece Container - 200 items & allen keys & Grease 500 Pc Mixed Bolt Cabinet Finishing Touches Reservoir Clip & Bolt (works with RESR10) Valve/Dust Caps with O Ring - Pair Valve/Dust Caps with O Ring - Set of 4 Brake Caliper Bleed Nipple Covers - Pair Brake Caliper Bleed Nipple Covers - Set of 3 6mm Hose Separator Mudguard & Hugger Kit - Qty 8 M6 Fairing Bolts Mudguard & Hugger Kit - Qty 8 M5Fairing Bolts Number Plate Kit - 2 Nuts & Bolts Number Plate Kit - 4 Nuts & Bolts Rubber Lined P Clip Socket Cap Allen Key Bolts - 5 pack M3 x 8 / 10 / 30mm M4 x 10 / 20 / 35mm M5 x 8 / 10 / 12 / 16 / 20 / 25 / 30 / 40mm lengths M6 x 10 / 12 / 16 / 20 / 25/ 30 / 35 / 40 / 45mm M6 x 50 / 55 / 60 / 65 / 70 / 80 / 90 / 95 / 100mm lengths M8 x 25 / 30 / 35 / 40 / 60mm lenghts

21,27 21,27 21,27 21,27 21,27 21,27 21,27 21,27 21,27 21,27 38,29 21,27 21,27 21,27 21,27 21,27 21,27 21,27 38,29 38,29 38,29 38,29 38,29 38,29 38,29 38,29 38,29 38,29 38,29 38,29 38,29 38,29 38,29 38,29 42,54 , 80,84 59,57 17,01 18,71 14,46 17,01 9,35 42,54 59,57 10,63 17,01 12,76 4,25 32,33 5,10 51,06 21,27 34,03 40,84 40,84 40,84 34,03 18,71 21,27 73,18 191,49 5,10 2,97 5,74 2,43 3,62 5,95 6,80 6,80 2,54 4,68 2,13 2,54 3,40 3,40 4,25 4,25 5,52
FB412 FB516 / FB525 FB516XL FB616 / FB620 etc FB840 CS415 / CS445 / CS450 CS520 / CS530 / CS535 CS615/CS625 / CS635 CS820 CS840 WAC5 WAC6-19 WAC6-22 WAC8 WA5 WA6-12 WA6-18 WA8 WAD5 WAD6 WAD8 WAD10 WAD12 FN5 FN6 FN8 NYN5 NYN6 NYN8 DOMENUT4-10 DOMENUT5-10 DOMENUT6-10 DOMENUT8-10 DOMENUT10F-10 DOMENUT10-10 BUT5 BUT6 BUT8 BUT10 WACP5 WACP6 WACP8 WACP10 PBTTL PBBRELLA PBCAP PATCH10
Screen Kits Fairing / Dome Head Allen Key Bolts - 5 Pack M4 x 12mm length (fine thread pitch bolt of 0.5mm) M5 x 16mm or 25mm length - 12mm head diameter M5 x 16mm - 16mm head diameter M6 x 16 / 20 / 25 / 30 / 35/ 40mm lengths - 16mm head diameter M8 x 40mm - 16mm head diameter Countersunk Allen Key Bolts - 3 pack M4 x 15 / 45/ 50 mm M5 x 20 / 30 / 35mm M6 x 15 / 25 / 35mm M8 x 20mm M8 x 40mm Countersunk Body Washers - 3 pack M5 Countersunk Washer - 13mm o/d M6 Countersunk Washer - 19mm o/d M6 Countersunk Washer - 22mm o/d M8 Countersunk Washer - 25mm o/d Flat Washers - 3 pack M5 Flat Washer - 10mm o/d M6 Flat Washer - 12mm o/d M6 Flat Washer - 18mm o/d M8 Flat Washer - 25mm o/d Drilled Washers - 3 pack M5 Drilled Washer - 10mm o/d M6 Drilled Washer - 23mm o/d M8 Drilled Washer -16mm o/d M10 Drilled Washer - 20mm o/d 12mm Drilled Washer - 25mm o/d Nuts - 5 pack M5 Full Nut M6 Full Nut M8 Full Nut M5 Nyloc Nut M6 Nyloc Nut M8 Nyloc Nut Dome Nuts - 10 pack M4 Dome Nuts - Pack of 10 M5 Dome Nuts - Pack of 10 M6 Dome Nuts - Pack of 10 M8 Dome Nuts - Pack of 10 1M0 Dome Nuts (1.25) - Pack of 10 M10 Dome Nuts (1.50) - Pack of 10 Cup Washers and Push In Buttons - 5 Pack Button Insert to Fit 5mm Bolt (4mm Allen Key) Button Insert to Fit 6mm Bolt (5mm Allen Key) Button Insert to Fit 8mm Bolt (6mm Allen Key) Button Insert to Fot 10mm Bolt (8mm Allen Key) Cup Washer to Fit over 5mm Threaded Bolt Cup Washer to Fit over 6mm Threaded Bolt Cup Washer to Fit over 8mm Threaded Bolt Cup Washers to Fit over 10mmThreaded Bolt Pro-Bolt Merchandising Tasty Nuts Logo T-Shirt - X'Large, Large, Med & Ladies Skinny Pro-Bolt Logo Umbrella Pro-Bolt 'Tasty Nuts' Baseball Cap Sew on Patch - Pro-Bolt Logo