MONITOR WITH DVD RECEIVER

DDX7019 DDX7039

INSTALLATION MANUAL

B54-4522-00/00 (KV/RV)

Accessories
1..1 2..1 3..2 4..1 5..1 6..6 7..6 8..1

DDX7019/DDX7039

Installation Procedure
1. To prevent a short circuit, remove the key from the ignition and disconnect the - battery. 2. Make the proper input and output wire connections for each unit. 3. Connect the speaker wires of the wiring harness. 4. Connect the wiring harness wires in the following order: ground, battery, ignition. 5. Connect the wiring harness connector to the unit. 6. Install the unit in your car. 7. Reconnect the - battery. 8. Press the reset button.
If the power is not turned ON (or it is ON, but will be OFF immediately), the speaker wire may have a short-circuit or touched the chassis of the vehicle and the protection function may have been activated. Therefore, the speaker wire should be checked. If your cars ignition does not have an ACC position, connect the ignition wires to a power source that can be turned on and off with the ignition key. If you connect the ignition wire to a power source with a constant voltage supply, as with battery wires, the battery may die. If the console has a lid, make sure to install the unit so that the faceplate will not hit the lid when closing and opening. If the fuse blows, first make sure the wires arent touching to cause a short circuit, then replace the old fuse with one with the same rating. Insulate unconnected wires with vinyl tape or other similar material. To prevent a short circuit, do not remove the caps on the ends of the unconnected wires or the terminals. Connect the speaker wires correctly to the terminals to which they correspond. The unit may be damaged or fail to work if you share the - wires or ground them to any metal part in the car. When only two speakers are being connected to the system, connect the connectors either to both the front output terminals or to both the rear output terminals (do not mix front and rear). For example, if you connect the + connector of the left speaker to a front output terminal, do not connect the - connector to a rear output terminal. After the unit is installed, check whether the brake lamps, blinkers, wipers, etc. on the car are working properly. Mount the unit so that the mounting angle is 30 or less. This unit has the cooling fan (page 5) to decrease the internal temperature. Do not mount the unit in a place where the cooling fan of the unit are blocked. Blocking these openings will inhibit the cooling of the internal temperature and result in malfunction.

2WARNING

If you connect the ignition wire (red) and the battery wire (yellow) to the car chassis (ground), you may cause a short circuit, that in turn may start a fire. Always connect those wires to the power source running through the fuse box. Do not cut out the fuse from the ignition wire (red) and the battery wire (yellow). The power supply must be connected to the wires via the fuse.

English |

Connection

Ignition key switch ACC

If you connect the ignition wire (red) and the battery wire (yellow) to the car chassis (ground), you may cause a short circuit, that in turn may start a fire. Always connect those wires to the power source running through the fuse box.

A B A B C

Ignition wire (Red) Battery wire (Yellow) Ground wire (Black) (To car chassis) FUSE ( 5A )
Car fuse box Car fuse box (Main fuse)
Connect to the vehicle's parking brake detection switch harness using the supplied relay connector. Parking sensor wire (Light Green)

PRK SW

Antenna Cord

Battery

For the sake of safety, be sure to connect the parking sensor.
To vehicle's reverse lamp harness
Reveres sensor wire (Purple/White)
To car light control switch
Dimmer control wire (Orange/White)
To steering remote Connect to the terminal that is grounded when either the telephone rings or during conversation. To connect the Kenwood navigation system, consult your navigation manual. Depending on what antenna you are using, connect either to the control terminal of the motor antenna, or to the power terminal for the booster amplifier of the film-type antenna. When using the optional power amplifier, connect to its power control terminal. To "EXT.AMP.CONT." terminal of the amplifier having the external amp control function.
Steering remote control input (Light Blue/Yellow)

Mute wire (Brown)

Motor antenna control wire (Blue)
Power control wire (Blue/White) External amplifier control wire (Pink/Black)
If no connections are made, do not let the cable come out from the tab.

Rear view

FUSE ( 10A )

Cooling fan

FM/AM antenna input Accessory 1

REVERSE

FRONT L

ILLUMI

White/Black White

To front left speaker

REMO.CONT FRONT R

Gray/Black Gray

To front right speaker

REAR L

Green/Black Green

To rear left speaker

REAR R

ANT. CONT

Purple/Black Purple

To rear right speaker

P CONT

EXT.CONT

System Connection
USB terminal USB device (commercially available)

Do not connect.

AV OUT
Audio/Visual Output Visual output (Yellow)

REAR VIEW CAMERA

Audio/Visual input Visual input (Yellow) Audio left input (White) Audio right input (Red) Rear View Camera Input Visual input (Yellow) Front Preout Audio left output (White) Audio right output (Red) Rear Preout Audio left output (White) Audio right output (Red) Subwoofer Preout Audio left output (White) Audio right output (Red) Audio/Visual Output Audio left output (White) Audio right output (Red) Audio Input Resistance-free stereo type mini plug Visual Input Resistance-free mini plug

iPod VIDEO IN

iPod AUDIO IN

SUB WOOFER

Optional Accessory Connection
iPod (commercially available)
Navigation System (Optional Accessory)
KCA-iP300V (Optional Accessory)

Audio Output (Black)

Audio Input
Connection cable (Included in the Navigation System)

Visual Input

Visual Output (Yellow)

USB terminal

Connection cable (Included in the Disc changer)
Disc Changer etc. (Optional Accessory)
Connection cable (Included in the TV tuner)
TV ANTENNA INPUT TO MONITOR UNIT
TV Tuner (Optional Accessory)
Installing the Escutcheon

For General Motors

1. Refer to the section <Removing the Hard Rubber Frame> and then remove the hard rubber frame. 2. Cut out accessory 4 to meet the shape of the opening of the center console. 3. Attach accessory 4 to the unit.
Cut out to meet the shape of the opening in the vehicle.

Accessory 4

For Toyota/Scion
1. Refer to the section <Removing the Hard Rubber Frame> and then remove the hard rubber frame. 2. Cut out accessory 4 as illustrated.

Cutting line

3. Fold double-sided adhesive (accessory 5) along the slit and attach it to accessory 4 cut-out against the center rib as illustrated. Use 2 pieces of accessory 5 for 1 accessory 4 cutout. 4. Attach accessory 4 cut-out to the unit.

Accessory 5

Installation for Monitor/Player Unit
Firewall or metal support
Screw (M4X8) (commercially available)
Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place. Self-tapping screw (commercially available) Metal mounting strap (commercially available) Accessory 2

Make sure that the unit is installed securely in place. If the unit is unstable, it may malfunction (eg, the sound may skip).
Installation on Toyota, Nissan or Mitsubishi Car using Brackets
Accessory 6 (M5x6mm) or Accessory 7 (M5x7mm)

Car Bracket

Removing Monitor/Player Unit
Removing the Hard Rubber Frame (escutcheon)
1. Engage the catch pins on the removal tool 3 and remove the two locks on the lower level. Lower the frame and pull it forward as shown in the figure.
Removal Tool (Accessory 3)

Removing the Unit

1. Remove the hard rubber frame by referring to the removal procedure in the section <Removing the Hard Rubber Frame>. 2. Remove the Hex-head screw with integral washer (M4 8) on the back panel. 3. Insert the two removal tools 3 deeply into the slots on each side, as shown.

Catch Lock

The frame can be removed from the top side in the same manner.
2. When the lower level is removed, remove the upper two locations.
4. Lower the removal tool toward the bottom, and pull out the unit halfway while pressing towards the inside.
Be careful to avoid injury from the catch pins on the removal tool.
5. Pull the unit all the way out with your hands, being careful not to drop it.