KAC-726 KAC-526X

POWER AMPLIFIER

INSTRUCTION MANUAL

B64-1213-00 (EM)

Safety precautions

2WARNING

Take the following precautions to prevent fire and avoid personal injury :
When extending the battery cable, or ground cable, use 5mm2 (AWG10) or larger automotive grade cable to avoid cable deterioration or damage to the covering. Check that no metal objects (coins, tools, etc.) are left inside the unit to avoid short circuits. If you smell or see smoke, turn the power off immediately and consult your Kenwood dealer. Do not touch the unit during use because the surface of the unit becomes hot and may cause burns if touched.
Do not open the top or bottom cover. Do not install the unit in places it is exposed to direct sunlight, high heat or humidity, water may splash over it, or dust exists.
If you have difficulty in installing this unit in your vehicle, contact your Kenwood dealer.

Cleaning the unit

If the surface is dirty, wipe it clean with a silicon cloth or soft dry cloth with the power off.

2CAUTION

Do not use hard cloths or paint thinner, alcohol, or other volatile solvents. These may damage external surfaces or remove indicator characters.
Take the following precautions to keep the unit in proper working order.
Be sure the unit is connected to a 12V DC power supply with a negative ground connection.

Accessories

Part name
Battery cable (Yellow) (6 m) Ground cable (Black) (1 m) Self-tapping screws (mm) Terminal cover (Power terminal)

External View

Number of Items
Round terminal (Large) Round terminal (Medium) Round terminal (Small) Grommets

Installation procedure

1. Remove the ignition key and disconnect the negative - terminal of the battery to prevent short circuits. 2. Set the unit according to the intended usage. 3. Connect the input and output cables of the units. 4. Connect the speaker cables. 5. Connect the power cable, power control cable and grounding cable following this order. 6. Install the unit in the car. 7. Connect the negative - terminal of the battery. 2CAUTION Be sure to turn the power off before changing the setting of any switch. If the fuse blows, check cables for shorts, then replace the fuse with one of the same rating. Check that no unconnected cables or connectors are touching the car body. Do not remove caps from unconnected cables or connectors to prevent short circuits. Connect the speaker cables to appropriate speaker connectors separately. Sharing the negative cable of the speaker or grounding speaker cables to the metal body of the car can cause this unit to fail. After installation, check that the brake lamps, winkers, and wipers work properly.

Installation

Self-tapping screw (mm)
Installation board, etc. (thickness : 15 mm or more) Since the power amplifier has no parts which require operation, it can be installed at a position away from the drivers seat without any hindrances. As generally accepted positions for its installation, places such as inside the trunk, etc. can be considered. Use the extension cables. (Optional.) Length 0.5m 1m 2m 4m 5m 6m Type RCA cable CA-2SL CA-12SL CA-22SL CA-52SL RCA cable (7mm) CA-3WL CA-13WL CA-23WL CA-53WL RCA cable (12mm) CA-5W CA-15W CA-25W CA-45W CA-65W 2CAUTION Do not install the unit under the carpet. Otherwise heat build-up occurs and the unit may be damaged. Install this unit in a location which allows heat to easily dissipate. Once installed, do not place any object on top of the unit. After installing the unit, check to make sure that electrical equipment such as the brake lamps, turn signal lamps and windshield wipers operate normally. Install the unit securely in a location that does not interfere with driving.

Controls

Operations of the following control and switches are required in accordance with the center unit and speakers connected with this unit.

FILTER

OFF LPF

OPERATION

STEREO MONO(Lch) 0.5 1.0 0.3
SPEAKER LEVEL INPUT LEFT RIGHT LINE IN L R

INPUT SENSITIVITY(V)

POWER IN
FUSE(20A x 2) BATT P.CON(REMOTE)

BRIDGED

RIGHT SPEAKER OUTPUT

KAC-726

FUSE(15A)

GND P.CON(REMOTE)

SPEAKER OUTPUT

KAC-526X

1 RCA cable ground lead terminal 2 FILTER switch
These switches allow filtering of the speaker output signals.
LPF (Low Pass Filter) position
Only frequencies of 80 Hz or lower are output. (Frequencies above 80 Hz are cut.) The Lch and Rch will be mixed before output even if the operation switch is set to STEREO.

OFF position

The original sound without filtering is output.

3 OPERATION switch

This switch allows selection of the amplification method of input signals.

STEREO position

The amplifier can be used as a stereo amplifier.

MONO (Lch) position

Amplifies the signal input from the left side only. Set to this position and make bridged connections to use as a high-power monaural amplifier. (The input right signal is not output.)
4 INPUT SENSITIVITY control
Set this control according to the pre-output level of the center unit connected with this unit, or to the maximum power output of the genuineaccessory car stereo. Use the diagram on the right as a guide.

1.0 MIN (W) MAX

NOTE For the pre-output level or the maximum power output, refer to the Specifications in the instruction manual of the center unit.
5 LINE IN terminal 6 Speaker level input terminals 7 Fuse (20 A 2 : KAC-726) Fuse (15 A : KAC-526X) 8 Battery terminal 9 Ground terminal 0 Power control (REMOTE) terminal ! SPEAKER OUTPUT terminals

Protection function

This unit is equipped with a protection function for protecting this unit and your speakers from various accidents or problems that can occur. When the protection function is triggered, the Power indicator goes off and the amplifier stops operating. s Power indicator:
When the power is turned on, the Power indicator lights. If the Power indicator does not light when the power is turned on, the protection function may be activated. Check whether there is any indication of trouble. Power indicator
s The protection function activates in the following situations:
When a speaker output contacts ground. When the unit malfunctions and a DC signal is sent to the speaker output. When the temperature of internal parts exceeds 120C (248F). When a ground cable of the center unit (cassette receiver, CD receiver, etc.) or this unit is not connected to a metal part serving as an electrical ground passing electricity to the battery's negative - terminal.

Connection

sRCA cable connection
2CAUTION Do not connect cables and leads to both RCA cable input jacks and the speaker input terminals simultaneously, for this may cause malfunction or damage. Left input Left output (White) Right output (Red) RCA cable (Commercially available part) Right input
SPEAKER LEVEL INPUT LEFT RIGHT LINE IN
CENTER UNIT (Cassette receiver, CD receiver, etc.)

Power control cable

STEREO MONO(Lch) 0.5 1.0
RCA cable ground terminal 2CAUTION When using an RCA cable with Do not use this terminal for power source a ground lead attached, connect grounding. This unit will be damaged if the the ground lead to this terminal. power source grounding wire is connected to this terminal.
sSpeaker level input connection
Connect the unit by inserting it in the connection between the genuine-accessory car stereo and speakers. Left output Right output Genuine-accessory car stereo ACC
Speaker level input terminals
Lead terminal (Commercially available parts)

Battey

Left input
OPERATION SPEAKER LEVEL INPUT LEFT RIGHT LINE IN

Right input

STEREO

MONO(Lch) 0.5 1.0

2CAUTION The genuine-accessory car stereo shall have a maximum power output of no more than 25 W. Do not connect the speaker output leads from a power amplifier (Optional) to the speaker input terminals of this unit, for this may cause malfunction or damage. Do not connect cables and leads to both RCA cable input jacks and the speaker input terminals simultaneously, for this may cause malfunction or damage. Connect the power control lead to a power supply which can be turned ON/OFF by the ignition key switch (ACC line). With this connection, shock noise may be generated when the power of the genuine-accessory car stereo is switched ON/OFF.
sPower and Speakers cable connection
Power control (REMOTE) lead terminal

BATT P.CON(REMOTE)

Terminal cover Power control cable Battery cable (Yellow) Ground cable (Black)
Right speaker Left speaker
If a buzzing noise is heard from the speakers when the engine is running, connect a line noise filter (optional) to each of the battery cable. Do not allow the cord to directly contact the edge of the iron plate by using Grommets. Fire wall Grommets Battery NOTE Connect the ground cable to a metal part of the car chassis that acts as an electrical ground passing electricity to the batterys negative - terminal. Do not turn the power on if the ground cable is not connected.

Round terminal (Large)

2WARNING To prevent fire caused by a short in the wiring, connect a fusible link or breaker nearby the batterys positive terminal.
Speaker output cable terminal Connect the speaker output cables to these terminals.
Lead terminal (Commercially available part) Speaker output cable
Power terminal Pass battery and ground cables through supplied terminal cover and connect to respective terminals. After completing connections, fasten terminal cover over terminal bracket. Round terminal (Medium) Round terminal (Small)

(Bridged)

2CAUTION If you wish to bridge-connect a speaker, the speaker impedance must be no less than 4 ohms. Connecting a speaker with an impedance lower than 4 ohms may damage the unit. examples:

Bridged

System examples
s Full-range 2-channel system

Switch setting

STEREO MONO(Lch)

CENTER UNIT

Left speaker Right speaker
s High-power full-range 2-channel system

L R L R

Left speaker (Bridged) Right speaker (Bridged)
s Full-range 2-channel + Subwoofer system
Left speaker Right speaker Subwoofer (L + R) (Bridged)

s Tri-mode

High pass
Subwoofer (L + R) (Bridged)
qPrinciple of Tri-mode Method of frequency band division using a coil and capacitorin case of 6dB/oct. slope Crossover Frequency 0 dB -3 dB

Frequency

qExample: When it is required to set a crossover frequency of 120 Hz using speakers with an impedance of 4 ohms. Prepare commercially-available coil and capacitor with the closest ratings to the results calculated from the formula above. The capacitor rating should be as close as possible to 331.25 (F) and the coil rating should be as close as possible to 5.3 (mH). 2CAUTION
Coil (L): Passes low frequencies and blocks high frequencies. (Low pass) Capacitor (C): Passes high frequencies and blocks low frequencies. (High pass) 159000 C= (F) fc=Cut of Frequency (Hz) fc x R R=Speaker Impedance () 159 x R L= (mH) fc
If you wish to bridge-connect a speaker, the speaker impedance must be no less than 4 ohms. Connecting a speaker with an impedance lower than 4 ohms may damage the unit.

Troubleshooting Guide

What might appear to be a malfunction in your unit may just be the result of slight misoperation or miswiring. Before calling service, first check the following table for possible problems. PROBLEM
No sound. (No sound from one side.)

POSSIBLE CAUSE

Input (or output) cables are disconnected. Protection circuit may be activated. The fuse may be blown because the volume was too high. The input sensitivity adjusting control is not set to the correct position. The speakers cable are connected with wrong + / polarity. A speaker cable is pinched by a screw in the car body. The switches may be set improperly.

SOLUTION

Connect the input (or output) cables. Check connections by referring to "Protection function". Replace the fuse with a new fuse and use a lower volume. Adjust the control correctly referring to Controls. Connect them properly checking the + / - of the terminals and cables well. Connect the speaker cable again so that it is not pinched by anything. Set switches properly by referring to "System examples".
The output level is too small (or too large). The sound quality is bad. (The sound is distorted.)

Specifications

Specifications subject to change without notice.

Audio Section

Max Power Output (4 ) Normal...200 W 2 Bridge...600 W 1 Rated Power Output (4 ) Normal (DIN45324, +B=14.4 V)..100 W 2 Bridge (1 kHz, 0.8 % THD)..300 W 1 Rated Power Output (2 ) Normal (1 kHz, 0.8 % THD)..150 W 2 Frequency Response (+0, 1 dB)..5 Hz ~ 50 kHz Signal to Noise Ratio..100 dB Sensitivity (MAX) (rated output)..0.2 V Sensitivity (MIN) (rated output)..5.0 V Input Impedance...10 k Low Pass Filter (12 dB/oct.)..80 Hz
70 W W W W W Hz ~ 50 kHz 100 dB 0.2 V 5.0 V 10 k 80 Hz 14.4 V 16 A 160 mm 1.6 kg

General

Operating Voltage (11 ~ 16 V allowable)..14.4 V Current Consumption (1 kHz, 10% THD)..28 A Dimensions (W H D).300 mm Weight...3.0 kg

KAC-8151D/8101D(KE) 1English

02.11.14

10:42 AM

Page 1

KAC-8151D KAC-8101D
MONO POWER AMPLIFIER 7 page 2-11

INSTRUCTION MANUAL

AMPLIFICATEUR DE PUISSANCE MONAURAL 7 page 12-21

MODE DEMPLOI

AMPLIFICADOR DE POTENCIA MONOFONICO 7 pgina 22-31

MANUAL DE INSTRUCCIONES

Take the time to read through this instruction manual. Familiarity with installation and operation procedures will help you obtain the best performance from your new power amplifier.

For your records

Record the serial number, found on the back of the unit, in the spaces designated on the warranty card, and in the space provided below. Refer to the model and serial numbers whenever you call upon your KENWOOD dealer for information or service on the product. Model KAC-8151D/8101D Serial number
PRINTED IN CHINA B64-2577-00/00 (KV/EV)

Page 2

Safety precautions

2WARNING

Cleaning the unit
If the front panel gets dirty, turn off the power and wipe the panel with a dry silicon cloth or soft cloth.

2CAUTION

To prevent injury or fire, take the following precautions: When extending the ignition, battery, or ground wires, make sure to use automotivegrade wires or other wires with a 5 mm2 (AWG 10) or more to prevent wire deterioration and damage to the wire coating. To prevent a short circuit, never put or leave any metallic objects (such as coins or metal tools) inside the unit. If the unit starts to emit smoke or strange smells, turn off the power immediately and consult your Kenwood dealer. Do not touch the unit during use because the surface of the unit becomes hot and may cause burns if touched.
Do not wipe the panel with a hard cloth or a cloth dampened by volatile solvents such as paint thinner and alcohol. They can scratch the surface of the panel and/or cause the indicator letters to peel off.

To prevent battery rise

When the unit is used in the ACC ON position without turning the engine ON, it depletes the battery. Use it after starting the engine.

Protection function

There is a Protection function installed in the unit to protect the unit and speakers from various problems. When Protection operates, the indicator informs you of the condition. (Refer to page 5)
To prevent damage to the machine, take the following precautions: Be sure the unit is connected to a 12V DC power supply with a negative ground connection. Do not open the top or bottom covers of the unit. Do not install the unit in a spot exposed to direct sunlight or excessive heat or humidity. Also avoid places with too much dust or the possibility of water splashing. When replacing a fuse, only use a new one with the prescribed rating. Using a fuse with the wrong rating may cause your unit to malfunction. To prevent a short circuit when replacing a fuse, first disconnect the wiring harness.

Accessories

Part name Self-tapping screws (mm) Terminal cover (Power terminal) Speaker level input cable External View Number of Items 1

(KAC-8151D only)

Part name Remote cable Remote controler Knob

External View

Number of Items 1
If you experience problems during installation, consult your Kenwood dealer. If the unit does not seem to be working right, consult your Kenwood dealer.

FCC WARNING

This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made.

+9 +12

Dressing plate Nut Washer Self-tapping screws (mm) Double-side tape

English

Page 3

Installation

Remote controler (KAC-8151D only)

Double-side tape

Remote cable

Remote controler

Knob Self-tapping screw (mm)
Self-tapping screw (mm) Dressing plate Washer Nut
Installation board, etc. (thickness : 15 mm or more)
Mount the Dressing plate according to the mount angle of the Remote Controller. Fully rotate the knob counterclockwise (CCW), and adjust the marking of the knob to the "OFF" position of the Dressing plate.
2CAUTION Do not install in the below locations; (Unstable location, In a location that interferes with driving, In a location that gets wet, In a dusty location, In a place that gets hot, In a place that gets direct sunlight, In a location that gets hit by hot air) Do not install the unit under the carpet. Otherwise heat build-up occurs and the unit may be damaged. Install this unit in a location which allows heat to easily dissipate. Once installed, do not place any object on top of the unit. The surface temperature of the amplifier will become hot during use. Install the amplifier in a place where people, resins, and other substances that are sensitive to heat will not come into contact with it. When making a hole under a seat, inside the trunk, or somewhere else in the vehicle, check that there is nothing hazardous on the opposite side such as a gasoline tank, brake pipe, or wiring harness, and be careful not to cause scratches or other damage. Do not install near the dashboard, rear tray, or air bag safety parts. The installation to the vehicle should securely fasten the unit to a place in which it will not obstruct driving. If the unit comes off due to a shock and hits a person or safety part, it may cause injury or an accident. After installing the unit, check to make sure that electrical equipment such as the brake lamps, turn signal lamps and windshield wipers operate normally.

Page 4

Controls / Indicator

(W) 10

1 EXPANDER switch
When this switch is turned ON the dynamic range is increased.
5 INPUT SENSITIVITY control
Set this control according to the pre-output level of the center unit connected with this unit, or to the maximum power output of the genuine-accessory car stereo. Use the diagram on the right as a guide.
2 LPF (Low-Pass Filter) FREQUENCY control
This control adjusts the frequency band output from this unit.

3 INFRASONIC switch

Ultralow frequencies that cannot be reproduced even by a subwoofer speaker do not become sound but become unnecessary oscillations, which affect the sound by causing distortion, etc. Setting this switch to "15 Hz" or "25 Hz" cuts the frequencies below the respective frequency. This improves the reproduction performance of the speakers by eliminating unnecessary oscillations which will not become sound.
For the pre-output level or the maximum power output, refer to the Specifications in the instruction manual of the center unit.
6 Remote controler control (KAC8151D only)
When the "BASS BOOST" switch is in the "OFF (REMOTE)" position, control the Bass Boost level from the Remote Controller.

OFF position:

BASS BOOST is OFF.

+6/+9/+12 position:

Boost the bass sound by +6 dB, +9 dB and +12 dB, respectively.

4 BASS BOOST switch

Sets the boost level for bass control.

12dB position:

BASS BOOST is +12 dB.

KAC-8101D: OFF position:

KAC-8151D: OFF(REMOTE) position:
Can be set from the Remote Controller.
If you have disconnected the Remote Controller, the BASS BOOST is turned OFF.

Page 5

7 Power indicator
When the power is turned on, the Power indicator lights. If the Power indicator does not light when the power is turned on, the protection function may be activated. Check whether there is any indication of trouble.
The protection function is activated in the following situations:
This unit is equipped with a protection function for protecting this unit and your speakers from various accidents or problems that can occur. When the protection function is triggered, the Power indicator goes off and the amplifier stops operating. When a speaker wire may be shortcircuited. When a speaker output contacts ground. When the unit malfunctions and a DC signal is sent to the speaker output. When the internal temperature is high and unit wont operate. When a ground wire of the center unit (cassette receiver, CD receiver, etc.) or this unit is not connected to a metal part serving as an electrical ground passing electricity to the battery's negative terminal.

Page 6

Connection

Terminal names

^ &

8 Fuse (40 A)

^ REMOTE terminal (KAC-8151D only)
Connects the Remote cable.
If you cant find the specified capacity fuse at your store etc., consult your Kenwood dealer.
9 Battery terminal 0 Ground terminal ! Power control terminal
Controls the unit ON/OFF.
Use the Remote cable of the accessory.
& Speaker level input terminals
Controls the unit power. Be sure to connect it with all the systems.
@ Speaker output terminals
As this unit accepts speakers with a minimum impedance of 1 ohm, connect speakers with 1-ohm or higher impedance to these terminals.
The rated input of the speakers should be no less than the maximum output of the amplifier. Otherwise malfunction may result.
# RCA cable ground lead terminal
When using an RCA cable with a ground lead attached, connect the ground lead to this terminal.
The genuine-accessory car stereo shall have a maximum power output of no more than 40 W. Do not connect the speaker output leads from a power amplifier (Optional) to the speaker level input terminals of this unit, for this may cause malfunction or damage. Do not connect cables and leads to both RCA cable input jacks and the speaker level input terminals simultaneously, for this may cause malfunction or damage. Connect the power control lead to a power supply which can be turned ON/OFF by the ignition key switch (ACC line). With this connection, shock noise may be generated when the power of the genuine-accessory car stereo is switched ON/OFF.
$ LINE IN terminal % LINE OUT terminal
The signal thats input from the line input terminal is output.

Page 7

Installation procedure
Since there are large variety of settings and connections possible according to applications, read the instruction manual well to select the proper setting and connection. 1. Remove the ignition key and disconnect the negative - terminal of the battery to prevent short circuits. 2. Set the unit according to the intended usage. 3. Connect the input and output wires of the units. 4. Connect the speaker wires. 5. Connect the power wire, power control wire and grounding wire following this order. 6. Install the unit in the car. 7. Connect the negative - terminal of the battery.

Wiring

Take the battery wire for this unit directly from the battery. If it's connected to the vehicles wiring harness, it can cause blown fuses etc. If a buzzing noise is heard from the speakers when the engine is running, connect a line noise filter (optional) to each of the battery wire. Do not allow the wire to directly contact the edge of the iron plate by using Grommets. Connect the ground wire to a metal part of the car chassis that acts as an electrical ground passing electricity to the batterys negative - terminal. Do not turn the power on if the ground wire is not connected. Be sure to install a protective fuse in the power cord near the battery. The protective fuse should be the same capacity as the units fuse capacity or somewhat larger. For the power cord and ground, use a vehicle type (fireproof) power wring cord with a current capacity greater than the units fuse capacity. (Use a power wiring cord with a diameter of 5 mm2 (AWG 10) or greater.) When more than one power amplifier are going to be used, use a power supply wiring wire and protective fuse of greater currenthandling capacity than the total maximum current drawn by each amplifier.
To prevent fire caused by a short in the wiring, connect a fusible link or breaker nearby the batterys positive terminal. 2CAUTION If sound is not output normally, immediately turn power off and check connections. Be sure to turn the power off before changing the setting of any switch. If the fuse blows, check wires for shorts, then replace the fuse with one of the same rating. Check that no unconnected wires or connectors are touching the car body. Do not remove caps from unconnected wires or connectors to prevent short circuits. Connect the speaker wires to appropriate speaker connectors separately. Sharing the negative wire of the speaker or grounding speaker wires to the metal body of the car can cause this unit to fail. After installation, check that the brake lamps, winkers, and wipers work properly.

Speaker Selection

The rated input power of the speakers that are going to be connected should be greater than the maximum output power (in Watts) of the amplifier. Use of speakers having input power ratings that are less than the output power of the amplifier will cause smoke to be emitted as well as damage. Use speakers that have an impedance of 1 or greater. When more than one set of speakers are going to be used, calculate the combined impedance of the speakers and then connect suitable speakers to the amplifier.

Combined impedance

Page 8
RCA cable or Speaker level input connection (RCA cable Connections)
RCA cable ground terminal
RCA cable* # $ CENTER UNIT (CD receiver, etc.)

Left input

Right input Power control wire (Blue/ White)
(Speaker level input Connections)
Cable Color of the connector White Left White/Black Gray Right Gray/Black Genuine-accessory car stereo (No line output center unit etc.) Car fuse box &

Battery ACC

Remote cable connection (KAC-8151D only)

Page 9

* Commercially available parts

Speaker wire connection

Lead terminal* @ @ Subwoofer (L + R)

Power wire connection

9 Terminal cover

0 ! Lead terminal*

Extension wire*

Battery wire*

Ground wire*

Protective Fuse* Battery

Page 10

Troubleshooting Guide

What might appear to be a malfunction in your unit may just be the result of slight misoperation or miswiring. Before calling service, first check the following table for possible problems.

PROBLEM

No sound. (No sound from one side.) (Blown fuse.)

POSSIBLE CAUSE

Input (or output) cables are disconnected. Protection circuit may be activated. Volume is too high. The speaker cord is shorted.

SOLUTION

Connect the input (or output) cables. Check connections by referring to "Indicator". Replace the fuse and use lower volume. After check the speaker cord and fixing the cause of the short, replace the fuse. Adjust the control correctly referring to Controls. Connect them properly checking the + / - of the terminals and wires well. Connect the speaker wire again so that it is not pinched by anything. Set switches properly by referring to "Controls". Set the "BASS BOOST" switch to the "OFF (REMOTE)" position. Connect the Remote Cable securely and correctly.
The output level is too small (or too large). The sound quality is bad. (The sound is distorted.)
The input sensitivity adjusting control is not set to the correct position. The speakers wire are connected with wrong + / polarity. A speaker wire is pinched by a screw in the car body. The switches may be set improperly.
The Remote Controller does not function.
The "BASS BOOST" switch is in the incorrect position. The Remote Cable is disconnected.

Page 11

Specifications
Specifications subject to change without notice. Audio Section
Max Power Output....1000 W 1 Rated Power Output (4 ) (20 Hz 200 Hz, 0.5 % THD)....200 W 1 (4 ) (DIN : 45324 , +B = 14.4V)...200 W 1 (2 ) (100 Hz, 0.5 % THD)....400 W 1 (1 ) (100 Hz, 1.0 % THD)....500 W 1 Frequency Response (+0, 3 dB)....5 Hz 200 Hz Sensitivity (rated output) (MAX.)...0.2 V Sensitivity (rated output) (MIN.)...5.0 V Signal to Noise Ratio....100 dB Input Impedance....10 k Low Pass Filter Frequency (18 dB/oct.)..Hz (variable) Infrasonic Filter Frequency (18 dB/oct.)...OFF / 15 / 25 Hz Bass Boost Circuit (90 Hz) KAC-8151D...OFF / +6 / +9 / +12 dB Bass Boost Circuit (90 Hz) KAC-8101D...OFF / +12 dB

General

Operating Voltage....14.4 V (V allowable) Current Consumption (4 , 10 % THD)...31 A Dimensions (W H D)...268 mm...11-1/4 2-1/4 10-9/16 inch Weight.....2.96 kg (6.5 lbs)