CD-RECEIVER

KDC-MP2032 KDC-MP2032CR KDC-MP232 KDC-MP202 KDC-232MR

INSTRUCTION MANUAL

Take the time to read through this instruction manual. Familiarity with installation and operation procedures will help you obtain the best performance from your new CD-receiver.

For your records

Record the serial number, found on the back of the unit, in the spaces designated on the warranty card, and in the space provided below. Refer to the model and serial numbers whenever you call upon your Kenwood dealer for information or service on the product. Model KDC-MP2032/MP2032CR/MP232/MP202/232MR Serial number

US Residence Only

Register Online
Register your Kenwood product at www.Kenwoodusa.com

B64-3290-10/02 (KW/K0)

Contents
Warning Safety precautions Notes About CDs About MP3 and WMA General features
Power Selecting the Source Volume Attenuator System Q Audio Control Audio Setup Speaker Setting Switching Display Dimmer Control Theft Deterrent Faceplate TEL Mute

Menu system

Menu System Activating Security Code Deactivating Security Code Touch Sensor Tone Manual Clock Adjustment DSI (Disabled System Indicator) Supreme Setting CRSC (Clean Reception System Circuit) Receive mode Setting SIRIUS ID (ESN) display Auxiliary Input Display Setting Text Scroll CD Read Setting Demonstration mode Setting
Basic Operations of remote control 24 Accessories/ Installation Procedure 26 Connecting Wires to Terminals Installation 12 Removing the Unit Troubleshooting Guide Specifications 34

Tuner features

Tuning Tuning Mode Station Preset Memory Auto Memory Entry Preset Tuning
CD/Audio file/External disc control features 14
Playing CD & Audio file Playing External Disc Fast Forwarding and Reversing Track/File Search Disc Search/Folder Search Direct Track/File Search Direct Disc Search Track/File/Disc/Folder Repeat Scan Play Random Play Magazine Random Play Folder Select Text/Title Scroll
HD Radio control features

About HD Radio Tuning

English

2Warning

2CAUTION
Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. In compliance with Federal Regulations, following are reproductions of labels on, or inside the product relating to laser product safety. Kenwood Corporation 2967-3, ISHIKAWA-MACHI, HACHIOJI-SHI TOKYO, JAPAN KENWOOD CORP. CERTIFIES THIS EQUIPMENT CONFORMS TO DHHS REGULATIONS N0.21 CFR 1040. 10, CHAPTER 1, SUBCHAPTER J. Location : Bottom Panel
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment may cause harmful interference to radio communications, if it is not installed and used in accordance with the instructions. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.

FCC WARNING

This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made.

English |

Safety precautions

2WARNING

To prevent injury or fire, take the following precautions:
To prevent a short circuit, never put or leave any metallic objects (such as coins or metal tools) inside the unit. Mounting and wiring this product requires skills and experience. For safetys sake, leave the mounting and wiring work to professionals.

This Class B digital apparatus complies with Canadian ICES-003.
If you experience problems during installation, consult your Kenwood dealer. When you purchase optional accessories, check with your Kenwood dealer to make sure that they work with your model and in your area. If the unit fails to operate properly, press the Reset button. The unit returns to factory settings when the Reset button is pressed. Press the reset button if the disc auto changer fails to operate correctly. Normal operation should be restored.
Before using this unit for the first time
This unit is initially set on the Demonstration mode. When using this unit for the first time, cancel the <Demonstration mode Setting> (page 23).
About SIRIUS Satellite radio tuner
Refer to the instruction manual of SIRIUS Satellite radio tuner KTC-SR901/SR902/SR903 (optional accessory), when connected, for the operation method. KDC-MP2032/KDC-MP232/KDC-232MR Refer to the sections of A models for operations.

FM/ 4 SCRL

Reset button We recommend the use of <Activating Security Code> (page 20) to prevent theft. The characters which can be displayed by this unit are A-Z 0-9 @ " ` % & * + = ,. / \ < > [ ] ( ) : ; ^-{}|~. The illustrations of the display and the panel appearing in this manual are examples used to explain more clearly how the controls are used. Therefore, what appears on the display in the illustrations may differ from what appears on the display on the actual equipment, and some of the illustrations on the display may be inapplicable.

DISP/C.S.

Cleaning the Unit
If the faceplate of this unit is stained, wipe it with a dry soft cloth such as a silicon cloth. If the faceplate is stained badly, wipe the stain off with a cloth moistened with neutral cleaner, then wipe it again with a clean soft dry cloth.
Applying spray cleaner directly to the unit may affect its mechanical parts. Wiping the faceplate with a hard cloth or using a volatile liquid such as thinner or alcohol may scratch the surface or erases characters.
Cleaning the Faceplate Terminals
If the terminals on the unit or faceplate get dirty, wipe them with a clean soft dry cloth.

About CDs

Handling CDs
Do not touch the recording surface of the CD.

Removing CDs

When removing CDs from this unit pull them out horizontally.

CDs that cannot be used

CDs that are not round cannot be used.
CD-R and CD-RW are easier to damage than a normal music CD. Use a CD-R or a CD-RW after reading the caution items on the package etc. Do not stick tape etc. on the CD, or use a CD with tape stuck on it.

When using a new CD

If the CD center hole or outside rim has burrs, use the CD only after removing the burrs with a ballpoint pen, etc.

Reattaching the Faceplate
1 Align the projections on the unit with the
grooves on the faceplate.

Projections Grooves

2 Push the faceplate in until it clicks.
The faceplate is locked in place, allowing you to use the unit.

AUTO/ AME

ST indicator

Band display

Frequency display

Preset station number

Tuning

Selecting the station.

Tuning Mode
Choose the tuning mode. Press the [AUTO] button. Each time you press the button, the Tuning mode alternates between the modes shown in the table below. Tuning mode Display Operation Auto seek "AUTO 1" Automatic search for a station. Preset station seek "AUTO 2" Search in order of the stations in the Preset memory. Manual "MANUAL" Normal manual tuning control.

1 Select tuner source

Press the [SRC] button. Select the "TUNER" display.

2 Select the band

Push the Control knob towards [FM] or [AM]. Each time you push the knob toward [FM], it switches between the FM1, FM2, and FM3 bands.

3 Tune up or down band

During reception of stereo stations the "ST" indicator is ON.

Station Preset Memory

Putting a station in the memory.

1 Select the band

Push the Control knob towards [FM] or [AM].
2 Select the frequency to put in the memory
3 Put the frequency in the memory
Press the desired [1] [6] button for at least 2 seconds. The preset number display blinks 1 time. On each band, 1 station can be put in the memory on each [1] [6] button.

Auto Memory Entry

Putting stations with good reception in the memory automatically.
1 Select the band for Auto Memory Entry

2 Open Auto Memory Entry

Press the [AME] button for at least 2 seconds. When 6 stations that can be received are put in the memory Auto Memory Entry closes.

Preset Tuning

Recalling the stations in the memory.

2 Recall the station

Press the desired [1] [6] button.
CD/Audio file/External disc control features

RDM/ 3

F.SEL M.RDM

Disc number

IN indicator

Track number

Play time
Playing CD & Audio file
When a disc is inserted Press the [SRC] button. Select the "CD" display.
When a CD is inserted, the "IN" indicator is ON.
Function of the KDC-MP2032/KDC-MP232/KDC232MR

Playing External Disc

Playing discs set in the optional accessory disc player connected to this unit. Press the [SRC] button. Select the display for the disc player you want. Display examples: Display "CD CH" "MD CH" Disc player CD changer MD changer
Pause and play Press the Control knob. Each time you press the knob, the audio pauses or plays. Eject the CD Press the [0] button.
Refer to <About MP3 and WMA> (page 7) for the Audio file by models you can play.
Pause and play Press the Control knob. Each time you press the knob, the audio pauses or plays.
Disc 10 is displayed as "0". The functions that can be used and the information that can be displayed will differ depending on the external disc players being connected.
Fast Forwarding and Reversing
Fast Forwarding Hold down toward [] with the Control knob. Release your finger to play the disc at that point. Reversing Hold down toward [4] with the Control knob. Release your finger to play the disc at that point.
There is no sound while the Audio file is being searched.
Function of the KDC-MP2032/KDC-MP232/KDC232MR Function of disc changers with remote control

Direct Disc Search

Doing Disc Search by entering the disc number.

1 Enter the disc number

Press the number buttons on the remote control.
2 Do Disc Search Press the [+] or [] button.
Cancelling Direct Disc Search Press the [38] button.
Input "0" to select disc 10.

Track/File Search

Searching for a song on the disc or in the Audio file folder. Push the Control knob towards [4] or [].
Function of disc changer/ Audio file
Disc Search/Folder Search
Selecting the disc set in the Disc changer or the folder recorded on the Audio file media. Push the Control knob towards [FM] or [AM].
Function of remote control

Direct Track/File Search

Doing Track/File Search by entering the track/file number.
1 Enter the track/file number

Push the Control knob towards [FM] or [AM]. With the [FM] of the Control knob, you move 1 level down and with the [AM] of the Control knob, 1 level up. Selecting a folder in the same level Push the Control knob towards [4] or []. With the [4] of the Control knob, you move to the previous folder, and with the [] of the Control knob, to the next folder. Returning to the top level Press the [3] button.
3 Decide the folder to play
Press the Control knob. The Folder Select mode releases, and the Audio file in the folder being displayed plays.
Cancelling the Folder Select mode Press the [F.SEL] button.

Text/Title Scroll

Scrolling the displayed CD text, Audio file text, or MD title. Push the Control knob toward [FM] for at least 2 seconds.
Function of the KDC-MP2032/KDC-MP232/KDC-232MR

About HD Radio

When you connect an HD Radio, Tuner features of the unit are disabled and changed to HD Radio tuner features. A portion of the setting methods including the Tuning Mode will change. With the HD Radio tuner, you can use the similar functions to <Station Preset Memory>, <Auto Memory Entry>, and <Preset Tuning> of Tuner features. Refer to Tuner features for how to use the functions.

1 Select HD Radio source

Press the [SRC] button. Select the "HD RADIO" display.

2 Select the HD FM band

Push the Control knob toward [FM]. Each time you push the knob to [FM], the band alternates between the HF1, HF2, and HF3 bands. Select the HD AM band Push the Control knob toward [AM].

Menu display

Menu System
Setting beep sound during operation, etc. functions. The Menu system basic operation method is explained here. The reference for the Menu items and their setting content is after this operation explanation.
You can continue by returning to step 2 and setting other items.

4 Exit Menu mode

Press the [MENU] button.
When other items those applicable to the basic operation method above are displayed, their setting content chart is entered. (Normally the setting listed at the top of the chart is the original setting.) Also, the explanation for items that are not applicable (<Manual Clock Adjustment> etc.) are entered step by step.

1 Enter Menu mode

Press the [MENU] button for at least 1 second. "MENU" is displayed.

2 Select the menu item

Push the Control knob towards [FM] or [AM]. Example: When you want to set the beep sound, select the "BEEP" display.

3 Set the menu item

Push the Control knob towards [4] or []. Example: When you select "BEEP", each time you push the knob it alternates between "BEEP ON" or "BEEP OFF". Select 1 of them as the setting. English |

Function of the KDC-MP2032/KDC-MP232/KDC232MR In Standby mode

Activating Security Code

Activating the Security Code disables the usage of audio unit by someone else. Once the Security Code is activated, the entry of authorized Security Code is required to turn on the audio unit when it is removed from the vehicle. Indication of this Security Code activation prevents your precious audio unit from stealing.
If you enter the wrong Code in steps 4 through 6, repeat from step 4.
Resetting the Security Code function when the audio unit is first used after removed from the battery power source or the Reset button is pressed
1 Turn the power ON. 2 Do the step 4 through 7 operation, and enter
the Security Code. "APPROVED" is displayed. Now, you can use the unit.
Set the Security Code when the <Demonstration mode Setting> (page 23) is set to OFF. You can set the Security Code with a 4 digit number of your choice. The Security Code cannot be displayed or referenced. Make a note of the Security Code and treasure it up.
When the Security Code function is activated, "CODE SET" changes to "CODE CLR". To deactivate the Security Code function, see the next section <Deactivating Security Code>.

2 Enter Menu mode

Press the [MENU] button for at least 1 second. When "MENU" is displayed, "CODE SET" is also displayed.
Deactivating Security Code
To deactivate the Security Code function.
3 Enter Security Code mode
Press the Control knob for at least 2 seconds. When "ENTER" is displayed, "CODE" is also displayed.
1 Select Security Code mode
Push the Control knob towards [FM] or [AM]. Select the "CODE CLR" display.
4 Select the digits to enter
2 Enter Security Code mode
Press the Control knob for at least 1 second. When "ENTER" is displayed, "CODE" is also displayed.
5 Select the Security Code numbers
3 Select the digits to enter
6 Repeat steps 4 and 5, and complete the

Security Code.

7 Confirm the Security Code
Press the Control knob for at least 3 seconds. When "RE-ENTER" is displayed, "CODE" is also displayed.

4 Select the Seciruty Code numbers
5 Repeat steps 3 and 4, and complete the
8 Do the step 4 through 7 operation, and
reenter the Security Code. "APPROVED" is displayed. The Security Code function activates.
6 Press the Control knob for at least 3 seconds.
"CLEAR" is displayed. The Security Code function deactivates.
If a wrong security code is entered, "ERROR" is displayed. Enter a correct security code.

In Standby mode

Touch Sensor Tone
Setting the operation check sound (beep sound) ON/OFF. Display "BEEP ON" "BEEP OFF" Setting Beep is heard. Beep canceled.
Function of the KDC-MP2032/KDC-MP2032CR/ KDC-MP232/KDC-MP202 In CD mode

Supreme Setting

When MP3 or WMA files encoded at a low bit rate (less than 96kbps (fs=32k, 44.1k, 48kHz)) are played, this function restores their high frequency region to approach the sound quality of equivalents of these files encoded at a high bit rate. Processing is optimized for the compression format used (MP3, or WMA), and adjustment is made for the bit rate used. Display "SPRM ON" "SPRM OFF" Setting Plays sound using the Supreme function. Plays the original sound stored in the audio file.
Manual Clock Adjustment 1 Select Clock Adjustment mode
Push the Control knob towards [FM] or [AM]. Select the "CLK ADJ" display.
2 Enter Clock Adjust mode
Press the Control knob for at least 1 second. The clock display blinks.
The sound effect may be imperceptible depending on the relationship between the audio file format and setting.

3 Adjust the hours

Push the Control knob towards [FM] or [AM]. Adjust the minutes Push the Control knob towards [4] or [].

In FM reception

4 Exit Clock adjustment mode
CRSC (Clean Reception System Circuit)
Temporarily have reception alternate from stereo to mono to reduce multi-path noise when listening to the FM station. Display "CRSC ON" "CRSC OFF" Setting The CRSC is ON. The CRSC is OFF.
DSI (Disabled System Indicator)
A red indicator will blink on the unit after the faceplate is removed, warning potential thieves. Display "DSI ON" "DSI OFF" Setting LED flashes. LED OFF.
Strong electrical fields (such as from power lines) may cause unstable sound quality when CRSC is turned ON. In such a situation, turn it OFF.
Function of the KDC-MP2032/KDC-MP232/KDC232MR In HD Radio mode

Receive mode Setting

Sets the receive mode.
Serial & SIRIUS ID (ESN) It is important to retain the unit serial number and the electronic SIRIUS Identification number for service activation and potential service changes.
1 Select the Receive mode
Push the Control knob towards [FM] or [AM]. Select the "HDR MODE" display.

2 Enter Receive mode

Press the Control knob for at least 1 second.
Auxiliary Input Display Setting
Selecting the display when alternating to Auxiliary input source.

3 Set the Receive mode

Push the Control knob towards [FM] or [AM]. Each time you push the knob, the Receive mode alternates between the modes shown in the table below. Receive mode Auto mode Display "AUTO" Operation Analog broadcasts and digital broadcasts will be switched automatically. When both are being transmitted, the digital broadcast will have priority. Digital broadcasts only. Analog broadcasts only.
1 Select Auxiliary input source
Press the [SRC] button. Select the "AUX EXT" display.
3 Select Auxiliary input display setting mode
Push the Control knob towards [FM] or [AM]. Select the "NAME SET" display.

Digital Analog

"DIGITAL" "ANALOG"
4 Enter Auxiliary input display setting mode
Press the Control knob for at least 1 second. The selected Auxiliary input display is displayed.

4 Exit Receive mode

Even if the Receive mode is set to "AUTO", when the Ball game mode program (non-delayed broadcast program) is received, the Receive mode will automatically switch to Analog broadcast only.
5 Select the Auxiliary input display
Push the Control knob towards [4] or []. Each time you push the knob, the display alternates as listed below. "AUX EXT" "DVD" "PORTABLE" "GAME" "VIDEO" "TV"

Function of the KDC-MP2032/KDC-MP232/KDC232MR In SIRIUS tuner source

SIRIUS ID (ESN) display

Displaying the SIRIUS ID (Electronic Serial Number). Display "ESN= ************"
6 Exit Auxiliary input display setting mode
When operation stops for 10 seconds, the name at that time is registered, and the Auxiliary input display setting mode closes. You can only set the Auxiliary input display when the auxiliary input of optional KCA-S210A is used.

Text Scroll

Setting the displayed text scroll. Display "SCL AUTO" "SCL MANU" Setting Repeats scroll. Scrolls when the display changes.
Demonstration mode Setting
Sets the demonstration mode.
1 Select the Demonstration mode
Push the Control knob towards [FM] or [AM]. Select the "DEMO" display.
The text scrolled is listed below. - CD text - Folder name/ File name/ Song title/ Artist name/ Album name - MD title - Text for the SIRIUS tuner source, HD Radio source, including Channel name, etc.
2 Set the Demonstration mode
Press the Control knob for at least 2 seconds. Each time you press the knob at least 2 seconds, the Demonstration mode alternates between the settings shown in the table below. Display "DEMO ON" "DEMO OFF" Setting The Demonstration mode function is ON. Exit Demonstration mode (Normal mode).
Function of the KDC-MP2032/KDC-MP2032CR/ KDC-MP232/KDC-MP202 In Standby mode

CD Read Setting

When there is a problem with playing a CD with special format, this setting plays the CD by force. Display "CD READ1" "CD READ2" Setting Play CD and Audio file. Play CD by force.
Setting "CD READ2" cannot play Audio file. Some music CDs may not play even in the "CD READ2" mode.
Accessory of the KDC-MP2032/KDC-MP232
Basic Operations of remote control

ATT VOL

38 FM+

DIRECT /OK

FM/AM/+/ Not Used

DIRECT/OK

ABC DEF GHI JKL MNO

[0] [9]

PRS TUV WXY QZ
Loading and Replacing the battery
Use two "AA"/ "R6"-size batteries. Slide the cover while pressing downwards to remove it as illustrated. Insert the batteries with the + and poles aligned properly, following the illustration inside the case.

Basic operations

[VOL] buttons Adjusts the volume. [SRC] button Each time you press the button, the source alternates. For the source alternating order refer to <Selecting the Source> (page 8). [ATT] button Turns the volume down quickly. When the button is pressed again, the volume returns to the previous level.
Store unused batteries out of the reach of children. Contact a doctor immediately if the battery is accidentally swallowed.

No sound can be heard, or the volume is low. The fader or balance settings are set all the way to one side. Center the fader and balance settings. The input/output wires or wiring harness are connected incorrectly. Reconnect the input/output wires or the wiring harness correctly. See the section on <Connecting Wires to Terminals>. The values of Volume offset are low. Turn up the Volume offset, referring to the section on <Audio Setup> (page 9). The sound quality is poor or distorted. One of the speaker wires is being pinched by a screw in the car. Check the speaker wiring. The speakers are not wired correctly. Reconnect the speaker wires so that each output terminal is connected to a different speaker. The Touch Sensor Tone doesnt sound. The preout jack is being used. The Touch Sensor Tone cant be output from the preout jack.

Tuner source

Radio reception is poor. The car antenna is not extended. Pull the antenna out all the way. The antenna control wire is not connected. Connect the wire correctly, referring to the section on <Connecting Wires to Terminals>.
Disc source Audio file source
"AUX EXT" is displayed without achieving External disc control mode. Unsupported disc changer is connected. Use the disc changer mentioned in the <About CD players/disc changers connected to this unit> (page 4) of the section on <Safety precautions>. The specified disc does not play, but another one plays instead. The specified CD is quite dirty. Clean the CD. The disc is loaded in a different slot from that specified. Eject the disc magazine and check the number for the specified disc. The disc is severely scratched. Try another disc instead. A CD ejects as soon as it is loaded. The CD is quite dirty. Clean the CD, referring to the CD cleaning of the section on <About CDs> (page 6). Cant remove disc. The cause is that more than 10 minutes has elapsed since the vehicle ACC switch was turned OFF. The disc can only be removed within 10 minutes of the ACC switch being turned OFF. If more than 10 minutes has elapsed, turn the ACC switch ON again and press the Eject button. The disc wont insert. Theres already another disc inserted. Press the [0] button and remove the disc. Direct Search cant be done. Another function is ON. Turn Random Play or other functions OFF. Track Search cant be done. For the discs/folders first or last song. For each disc/folder, Track Search cant be done in the backward direction for the first song or in the forward direction for the last song.

Cannot play an Audio file. The media is scratched or dirty. Clean the media, referring to the CD cleaning of the section on <About CDs> (page 6). The sound skips when an Audio file is being played. The media is scratched or dirty. Clean the media, referring to the CD cleaning of the section on <About CDs> (page 6). The recording condition is bad. Record the media again or use another media. The Audio file track time isnt displayed correctly. -- There are times when it isnt displayed correctly according to the Audio file recording conditions. Supreme does not take effect when it is turned ON. Little high-frequency component. Supreme would not take effect with songs with little high-frequency component. Songs that have not been encoded at bit rates lower than 96 kbps (fs = 32k, 44.1 k, 48 kHz)or those that have been encoded at a variable bit rate cannot be decoded to reproduce their highfrequency components. ---

HD Radio source

No sound can be heard, or the volume is low. The preset broadcast station is not transmitting in the mode that was set with <Receive mode Setting> (page 22). Please set <Receive mode Setting> to "AUTO". In digital AM broadcasting, receive mode switches between stereo and monaural too often. Receiving condition is bad or unstable. Stereo is chosen when receiving condition is good, and it switches to monaural when the condition becomes bad. HD Radio tuner is connected to KCA-S210A or other units. Connect the HD Radio tuner directly to the control unit.
The messages shown below display your systems condition.
EJECT: No disc magazine has been loaded in the changer. The disc magazine is not completely loaded. Load the disc magazine properly. No CD in the unit. Insert the CD. No disc has been loaded in the disc magazine. Load a disc into the disc magazine. No disc has been loaded in the disc magazine. Load a disc into the disc magazine. The CD is quite dirty. The CD is upsidedown. The CD is scratched a lot. Clean the CD and load it correctly. The CD is upside-down. Load the CD correctly. Nothing has been recorded on the MD. No tracks are recorded on the MD, although it has a title. Media was played that doesnt have data recorded that the unit can play. Use media that has data recorded that the unit can play. The faceplate of the slave unit being connected to this unit has been removed. Replace it. The unit is malfunctioning for some reason. Press the reset button on the unit. If the "E-77" code does not disappear, consult your nearest service center. Something is wrong with the disc magazine. Or the unit is malfunctioning for some reason. Check the disc magazine. And then press the reset button on the unit. If the "E-99" code does not disappear, consult your nearest service center.

The protective circuit in the unit activates when the temperature inside the automatic disc changer exceeds 60C (140F), stopping all operation. Cool down the unit by opening the windows or turning on the air conditioner. As the temperature falls below 60C (140F), the disc will start playing again. Discs are being exchanged in the Disc changer. The unit is reading the data on the disc. The CD player section is not operating properly. Reinsert the CD. If the CD cannot be ejected or the display continues to flash even when the CD has been properly reinserted, please switch off the power and consult your nearest service center. The speaker wire has a short-circuit or touches the chassis of the vehicle, and then the protection function is activated. Wire or insulate the speaker cable properly and press the reset button. An Audio file is played with a format that this unit cant support. ---A copy-protected file is played. ---The Demonstration mode has been selected. The <Demonstration mode Setting> (page 23) is ON. Turn it OFF.

NO DISC:

LOAD: READING: IN (Blink):

TOC ERR:

E-05: BLANK: NO TRACK: E-15:

PROTECT:

NA FILE:

NO PANEL:

COPY PRO: DEMO:

Specifications

Specifications subject to change without notice.

FM tuner section

Frequency range (200 kHz space) : 87.9 MHz 107.9 MHz Usable sensitivity (S/N = 30dB) : 9.3dBf (0.8 V /75 ) Quieting Sensitivity (S/N = 50dB) : 15.2dBf (1.6 V /75 ) Frequency response (3.0 dB) : 30 Hz 15 kHz Signal to Noise ratio (MONO) : 70 dB Selectivity (400 kHz) : 80 dB Stereo separation (1 kHz) : 40 dB

Audio section

Maximum output power KDC-MP2032/232MR : 50 W x 4 KDC-MP2032CR/MP232/MP202 : 45 W x 4 Full Bandwidth Power (at less than 1% THD) : 22 W x 4 Speaker impedance :4-8 Tone action Bass : 100 Hz 8 dB Middle : 1 kHz 8 dB Treble : 10 kHz 8 dB Preout level / Load (during disc play) : 2000 mV/10 k Preout impedance : 600

AM tuner section

Frequency range (10 kHz space) : 530 kHz 1700 kHz Usable sensitivity (S/N = 20dB) : 28 dB (25 V)
Operating voltage (11 16V allowable) : 14.4 V Current consumption : 10 A Installation Size (W x H x D) : 182 x 53 x 155 mm 7-3/16 x 2-1/16 x 6-1/8 inch Weight : 3.1 lbs (1.40 kg)

CD player section

Laser diode : GaAlAs Digital filter (D/A) : 8 Times Over Sampling D/A Converter : 1 Bit Spindle speed KDC-MP2032/MP2032CR/MP232/MP202 : rpm (CLV 2times) KDC-232MR : rpm (CLV) Wow & Flutter : Below Measurable Limit Frequency response (1 dB) : 10 Hz 20 kHz Total harmonic distortion (1 kHz) : 0.01 % Signal to Noise ratio (1 kHz) KDC-MP2032/MP2032CR/MP232/MP202 : 105 dB KDC-232MR: 93 dB Dynamic range : 93 dB MP3 decode KDC-MP2032/MP2032CR/MP232/MP202 : Compliant with MPEG-1/2 Audio Layer-3 WMA decode KDC-MP2032/MP2032CR/MP232/MP202 : Compliant with Windows Media Audio