You can damage both your unit and the CD changer if you connect them incorrectly.
To prevent damage to the machine, take the following precautions:
Make sure to ground the unit to a negative 12V DC power supply. Do not install the unit in a spot exposed to direct sunlight or excessive heat or humidity. Also avoid places with too much dust or the possibility of water splashing. Do not place the faceplate (and the faceplate case) in areas exposed to direct sunlight, excessive heat or humidity. Also avoid places with too much dust or the possibility of water splashing. To prevent deterioration, do not touch the terminals of the unit or faceplate with your fingers. Do not subject the faceplate to excessive shock, as it is a piece of precision equipment. When replacing a fuse, only use a new fuse with the prescribed rating. Using a fuse with the wrong rating may cause your unit to malfunction. Do not use your own screws. Use only the screws provided. If you use the wrong screws, you could damage the unit.

Lens Fogging

When you turn on the car heater in cold weather, dew or condensation may form on the lens in the CD player of the unit. Called lens fogging, this condesnation on the lens may not allow CDs to play. In such a situation, remove the disc and wait for the condensation to evaporate. If the unit still does not operate normally after a while, consult your Kenwood dealer.
Do Not Load 3-in. CDs in the CD slot
If you try to load a 3 in. CD with its adapter into the unit, the adapter might separate from the CD and damage the unit.
This Class B digital apparatus complies with Canadian ICES-003.
If you experience problems during installation, consult your Kenwood dealer. When you purchase optional accessories, check with your Kenwood dealer to make sure that they work with your model and in your area. If the unit fails to operate properly, press the Reset button. The unit returns to factory settings when the Reset button is pressed. Press the reset button if the disc auto changer fails to operate correctly. Normal operation should be restored.
Before using this unit for the first time
This unit is initially set on the Demonstration mode. When using this unit for the first time, cancel the <Demonstration mode Setting> (page 23).
About SIRIUS Satellite radio tuner
Refer to the instruction manual of SIRIUS Satellite radio tuner KTC-SR901/SR902/SR903 (optional accessory), when connected, for the operation method. KDC-MP2032/KDC-MP232/KDC-232MR Refer to the sections of A models for operations.

General features

Release button

Control knob

ATT/DIM

LOUD indicator

ATT indicator

Clock display

Turning ON the Power Press the [SRC] button. Turning OFF the Power Press the [SRC] button for at least 1 second.

Volume

Increasing Volume Turn the [VOL] knob clockwise. Decreasing Volume Turn the [VOL] knob counterclockwise.

Selecting the Source

Press the [SRC] button. Source required SIRIUS tuner* (Optional accessory) Tuner or HD Radio* (Optional accessory) CD External disc* (Optional accessory) Auxiliary input* (Optional accessory) Standby (Illumination only mode) Display "SIRIUS" "TUNER" or "HD RADIO" "CD" "CD CH" "AUX EXT" "STANDBY"

Attenuator

Turning the volume down quickly. Press the [ATT] button. Each time you press the button, the Attenuator turns ON and OFF. When the Attenuator is ON, the "ATT" indicator blinks.

System Q

Selecting the best sound setting preset for different types of music.
* Function of the KDC-MP2032/MP232/232MR The power will be turned off automatically after about 20 minutes have elapsed under the standby mode (KDC-232MR only).
1 Select the source to set

Press the [SRC] button.

| English

2 Select the Sound type

Press the [Q] button. When you press the button once, the current sound setting is displayed. Each time you press the button, the sound setting alternates. Sound setting Natural Rock Pops Easy Top 40 Jazz Display "NATURAL" "ROCK" "POPS" "EASY" "TOP40" "JAZZ"

Audio Setup

Setting the Sound system, such as Volume offset and Loudness.
1 Select the source to adjust

2 Enter Audio Setup mode

Press the [VOL] knob for at least 1 second.
3 Select the Audio Setup item to adjust
Press the [VOL] knob. Each time you press the knob, the item to be adjusted alternates between the items shown in the table below.
4 Adjust the Audio setup item
Change each setting value with the <Speaker Setting> (page 10). First, select the speaker type with the Speaker setting. When the value is set up by <Audio Control> (page 9), "USER" is displayed.
Turn the [VOL] knob. Adjustment Item Volume offset Loudness Display "V-OFF" "LOUD" Range ON/OFF

Information Display Disc title (In External disc source or KDC- "D-TITLE"* MP2032/MP2032CR/MP232/MP202 internal CD source) Track title (In External disc source or KDC- "T-TITLE"* MP2032/MP2032CR/MP232/MP202 internal CD source)

Dimmer Control

You can lower the brightness of the display by using the dimmer function. Press the [DIM] button for at least 1 second. Each time you press the button for 1 second, the Dimmer contol turns ON or OFF. When the Dimmer control is ON, "DIM ON" is displayed.

TEL Mute

The audio system automatically mutes when a call comes in.
When a call comes in "CALL" is displayed. The audio system pauses. Listening to the audio during a call Press the [SRC] button. The "CALL" display disappears and the audio system comes back ON. When the call ends Hang up the phone. The "CALL" display disappears and the audio system comes back ON.
To use the TEL Mute feature, you need to hook up the MUTE wire to your telephone using a commercial telephone accessory. Refer to <Connection Wires to Terminals> (page 27).
Theft Deterrent Faceplate
The faceplate of the unit can be detached and taken with you, helping to deter theft.
Removing the Faceplate Press the Release button. The faceplate unlocks, allowing you to detach it.
The faceplate is a precision piece of equipment and can be damaged by shocks or jolts. Keep the faceplate in its faceplate case while detached. Do not expose the faceplate (and the faceplate case) to direct sunlight or excessive heat or humidity. Also avoid places with too much dust or the possibility of water splashing.
Reattaching the Faceplate
1 Align the projections on the unit with the
grooves on the faceplate.

Projections Grooves

2 Push the faceplate in until it clicks.
The faceplate is locked in place, allowing you to use the unit.

AUTO/ AME

ST indicator

Band display

Frequency display

Preset station number

Tuning

Selecting the station.

Tuning Mode
Choose the tuning mode. Press the [AUTO] button. Each time you press the button, the Tuning mode alternates between the modes shown in the table below. Tuning mode Display Operation Auto seek "AUTO 1" Automatic search for a station. Preset station seek "AUTO 2" Search in order of the stations in the Preset memory. Manual "MANUAL" Normal manual tuning control.

1 Select tuner source

Press the [SRC] button. Select the "TUNER" display.

2 Select the band

Push the Control knob towards [FM] or [AM]. Each time you push the knob toward [FM], it switches between the FM1, FM2, and FM3 bands.

3 Tune up or down band

During reception of stereo stations the "ST" indicator is ON.

Station Preset Memory

Putting a station in the memory.

1 Select the band

Push the Control knob towards [FM] or [AM].
2 Select the frequency to put in the memory
3 Put the frequency in the memory
Press the desired [1] [6] button for at least 2 seconds. The preset number display blinks 1 time. On each band, 1 station can be put in the memory on each [1] [6] button.

Auto Memory Entry

Putting stations with good reception in the memory automatically.
1 Select the band for Auto Memory Entry

2 Open Auto Memory Entry

Press the [AME] button for at least 2 seconds. When 6 stations that can be received are put in the memory Auto Memory Entry closes.

Preset Tuning

Recalling the stations in the memory.

2 Recall the station

Press the desired [1] [6] button.
CD/Audio file/External disc control features

RDM/ 3

F.SEL M.RDM

Disc number

IN indicator

Track number

Play time
Playing CD & Audio file
When a disc is inserted Press the [SRC] button. Select the "CD" display.
When a CD is inserted, the "IN" indicator is ON.

Function of the KDC-MP2032/KDC-MP232/KDC232MR

Playing External Disc

Playing discs set in the optional accessory disc player connected to this unit. Press the [SRC] button. Select the display for the disc player you want. Display examples: Display "CD CH" "MD CH" Disc player CD changer MD changer
Pause and play Press the Control knob. Each time you press the knob, the audio pauses or plays. Eject the CD Press the [0] button.
Refer to <About MP3 and WMA> (page 7) for the Audio file by models you can play.
Pause and play Press the Control knob. Each time you press the knob, the audio pauses or plays.
Disc 10 is displayed as "0". The functions that can be used and the information that can be displayed will differ depending on the external disc players being connected.
Fast Forwarding and Reversing
Fast Forwarding Hold down toward [] with the Control knob. Release your finger to play the disc at that point. Reversing Hold down toward [4] with the Control knob. Release your finger to play the disc at that point.
There is no sound while the Audio file is being searched.
Function of the KDC-MP2032/KDC-MP232/KDC232MR Function of disc changers with remote control

Direct Disc Search

Doing Disc Search by entering the disc number.

1 Enter the disc number

Press the number buttons on the remote control.
2 Do Disc Search Press the [+] or [] button.
Cancelling Direct Disc Search Press the [38] button.
Input "0" to select disc 10.

Track/File Search

Searching for a song on the disc or in the Audio file folder. Push the Control knob towards [4] or [].
Function of disc changer/ Audio file
Disc Search/Folder Search
Selecting the disc set in the Disc changer or the folder recorded on the Audio file media. Push the Control knob towards [FM] or [AM].
Function of remote control

Direct Track/File Search

Doing Track/File Search by entering the track/file number.
1 Enter the track/file number

2 Do Track/File Search

Press the [4] or [] button.
Cancelling Direct Track/File Search Press the [38] button.
Track/File/Disc/Folder Repeat
Replaying the song, disc in the Disc changer or Audio file folder you are listening to. Press the [REP] button. Each time you press the button, the Repeat Play alternates between the modes shown in the tables below.
Function of the KDC-MP2032/KDC-MP232/KDC232MR Function of disc changer

Magazine Random Play

Play the songs on all the discs in the disc changer in random order. Press the [M.RDM] button. Each time you press the button, the Magazine Random Play turns ON or OFF. When the Magazine Random mode is ON, "MGZN RDM" is displayed.

When you push the Control knob toward [], the next random song starts.
Repeat play Track Repeat Disc Repeat (In Disc Changer) OFF Display "TRAC REP" "DISC REP" "REP OFF"
Repeat play File Repeat Folder Repeat OFF Display "FILE REP" "FOLD REP" "REP OFF"
Function of the KDC-MP2032/KDC-MP2032CR/ KDC-MP232/KDC-MP202 Function of Audio file

Folder Select

Quickly selecting the folder you want to hear.

Scan Play

Playing the first part of each song on the disc or Audio file folder you are listening to and searching for the song you want to hear.
1 Enter Folder Select mode
Press the [F.SEL] button. "FOLD SEL" is displayed. During Select mode the folder information is displayed as shown below. Folder name display Displays the current folder name.

1 Start Scan Play

Press the [SCAN] button. "TRAC SCN"/"FILE SCN" is displayed.
2 Release it when the song you want to hear is
played Press the [SCAN] button.
2 Select the folder level Random Play
Play all the songs on the disc or Audio file folder in random order. Press the [RDM] button. Each time you press the button, Random Play turns ON or OFF. When the Random mode is ON, "DISC RDM"/ "FOLD RDM" is displayed.
Push the Control knob towards [FM] or [AM]. With the [FM] of the Control knob, you move 1 level down and with the [AM] of the Control knob, 1 level up. Selecting a folder in the same level Push the Control knob towards [4] or []. With the [4] of the Control knob, you move to the previous folder, and with the [] of the Control knob, to the next folder. Returning to the top level Press the [3] button.
3 Decide the folder to play
Press the Control knob. The Folder Select mode releases, and the Audio file in the folder being displayed plays.
Cancelling the Folder Select mode Press the [F.SEL] button.

Text/Title Scroll

Scrolling the displayed CD text, Audio file text, or MD title. Push the Control knob toward [FM] for at least 2 seconds.
Function of the KDC-MP2032/KDC-MP232/KDC-232MR

About HD Radio

When you connect an HD Radio, Tuner features of the unit are disabled and changed to HD Radio tuner features. A portion of the setting methods including the Tuning Mode will change. With the HD Radio tuner, you can use the similar functions to <Station Preset Memory>, <Auto Memory Entry>, and <Preset Tuning> of Tuner features. Refer to Tuner features for how to use the functions.

1 Turn the power ON. 2 Do the step 4 through 7 operation, and enter
the Security Code. "APPROVED" is displayed. Now, you can use the unit.
Set the Security Code when the <Demonstration mode Setting> (page 23) is set to OFF. You can set the Security Code with a 4 digit number of your choice. The Security Code cannot be displayed or referenced. Make a note of the Security Code and treasure it up.
When the Security Code function is activated, "CODE SET" changes to "CODE CLR". To deactivate the Security Code function, see the next section <Deactivating Security Code>.

2 Enter Menu mode

Press the [MENU] button for at least 1 second. When "MENU" is displayed, "CODE SET" is also displayed.
Deactivating Security Code
To deactivate the Security Code function.
3 Enter Security Code mode
Press the Control knob for at least 2 seconds. When "ENTER" is displayed, "CODE" is also displayed.
1 Select Security Code mode
Push the Control knob towards [FM] or [AM]. Select the "CODE CLR" display.
4 Select the digits to enter
2 Enter Security Code mode
Press the Control knob for at least 1 second. When "ENTER" is displayed, "CODE" is also displayed.
5 Select the Security Code numbers
3 Select the digits to enter
6 Repeat steps 4 and 5, and complete the

Security Code.

7 Confirm the Security Code
Press the Control knob for at least 3 seconds. When "RE-ENTER" is displayed, "CODE" is also displayed.
4 Select the Seciruty Code numbers
5 Repeat steps 3 and 4, and complete the
8 Do the step 4 through 7 operation, and
reenter the Security Code. "APPROVED" is displayed. The Security Code function activates.
6 Press the Control knob for at least 3 seconds.
"CLEAR" is displayed. The Security Code function deactivates.
If a wrong security code is entered, "ERROR" is displayed. Enter a correct security code.

In Standby mode

Touch Sensor Tone
Setting the operation check sound (beep sound) ON/OFF. Display "BEEP ON" "BEEP OFF" Setting Beep is heard. Beep canceled.
Function of the KDC-MP2032/KDC-MP2032CR/ KDC-MP232/KDC-MP202 In CD mode

Supreme Setting

When MP3 or WMA files encoded at a low bit rate (less than 96kbps (fs=32k, 44.1k, 48kHz)) are played, this function restores their high frequency region to approach the sound quality of equivalents of these files encoded at a high bit rate. Processing is optimized for the compression format used (MP3, or WMA), and adjustment is made for the bit rate used. Display "SPRM ON" "SPRM OFF" Setting Plays sound using the Supreme function. Plays the original sound stored in the audio file.

Manual Clock Adjustment 1 Select Clock Adjustment mode
Push the Control knob towards [FM] or [AM]. Select the "CLK ADJ" display.
2 Enter Clock Adjust mode
Press the Control knob for at least 1 second. The clock display blinks.
The sound effect may be imperceptible depending on the relationship between the audio file format and setting.

3 Adjust the hours

Push the Control knob towards [FM] or [AM]. Adjust the minutes Push the Control knob towards [4] or [].

In FM reception

4 Exit Clock adjustment mode
CRSC (Clean Reception System Circuit)
Temporarily have reception alternate from stereo to mono to reduce multi-path noise when listening to the FM station. Display "CRSC ON" "CRSC OFF" Setting The CRSC is ON. The CRSC is OFF.
DSI (Disabled System Indicator)
A red indicator will blink on the unit after the faceplate is removed, warning potential thieves. Display "DSI ON" "DSI OFF" Setting LED flashes. LED OFF.
Strong electrical fields (such as from power lines) may cause unstable sound quality when CRSC is turned ON. In such a situation, turn it OFF.
Function of the KDC-MP2032/KDC-MP232/KDC232MR In HD Radio mode

Receive mode Setting

Sets the receive mode.
Serial & SIRIUS ID (ESN) It is important to retain the unit serial number and the electronic SIRIUS Identification number for service activation and potential service changes.
1 Select the Receive mode
Push the Control knob towards [FM] or [AM]. Select the "HDR MODE" display.

2 Enter Receive mode

Press the Control knob for at least 1 second.
Auxiliary Input Display Setting
Selecting the display when alternating to Auxiliary input source.

3 Set the Receive mode

Push the Control knob towards [FM] or [AM]. Each time you push the knob, the Receive mode alternates between the modes shown in the table below. Receive mode Auto mode Display "AUTO" Operation Analog broadcasts and digital broadcasts will be switched automatically. When both are being transmitted, the digital broadcast will have priority. Digital broadcasts only. Analog broadcasts only.
1 Select Auxiliary input source
Press the [SRC] button. Select the "AUX EXT" display.

3 Select Auxiliary input display setting mode
Push the Control knob towards [FM] or [AM]. Select the "NAME SET" display.

Digital Analog

"DIGITAL" "ANALOG"
4 Enter Auxiliary input display setting mode
Press the Control knob for at least 1 second. The selected Auxiliary input display is displayed.

4 Exit Receive mode

Even if the Receive mode is set to "AUTO", when the Ball game mode program (non-delayed broadcast program) is received, the Receive mode will automatically switch to Analog broadcast only.
5 Select the Auxiliary input display
Push the Control knob towards [4] or []. Each time you push the knob, the display alternates as listed below. "AUX EXT" "DVD" "PORTABLE" "GAME" "VIDEO" "TV"
Function of the KDC-MP2032/KDC-MP232/KDC232MR In SIRIUS tuner source

SIRIUS ID (ESN) display

Displaying the SIRIUS ID (Electronic Serial Number). Display "ESN= ************"
6 Exit Auxiliary input display setting mode
When operation stops for 10 seconds, the name at that time is registered, and the Auxiliary input display setting mode closes. You can only set the Auxiliary input display when the auxiliary input of optional KCA-S210A is used.

Text Scroll

Setting the displayed text scroll. Display "SCL AUTO" "SCL MANU" Setting Repeats scroll. Scrolls when the display changes.
Demonstration mode Setting
Sets the demonstration mode.
1 Select the Demonstration mode
Push the Control knob towards [FM] or [AM]. Select the "DEMO" display.
The text scrolled is listed below. - CD text - Folder name/ File name/ Song title/ Artist name/ Album name - MD title - Text for the SIRIUS tuner source, HD Radio source, including Channel name, etc.
2 Set the Demonstration mode
Press the Control knob for at least 2 seconds. Each time you press the knob at least 2 seconds, the Demonstration mode alternates between the settings shown in the table below. Display "DEMO ON" "DEMO OFF" Setting The Demonstration mode function is ON. Exit Demonstration mode (Normal mode).
Function of the KDC-MP2032/KDC-MP2032CR/ KDC-MP232/KDC-MP202 In Standby mode

CD Read Setting

When there is a problem with playing a CD with special format, this setting plays the CD by force. Display "CD READ1" "CD READ2" Setting Play CD and Audio file. Play CD by force.

Setting "CD READ2" cannot play Audio file. Some music CDs may not play even in the "CD READ2" mode.
Accessory of the KDC-MP2032/KDC-MP232
Basic Operations of remote control

ATT VOL

38 FM+

DIRECT /OK

FM/AM/+/ Not Used

DIRECT/OK

ABC DEF GHI JKL MNO

[0] [9]

PRS TUV WXY QZ
Loading and Replacing the battery
Use two "AA"/ "R6"-size batteries. Slide the cover while pressing downwards to remove it as illustrated. Insert the batteries with the + and poles aligned properly, following the illustration inside the case.

Basic operations

[VOL] buttons Adjusts the volume. [SRC] button Each time you press the button, the source alternates. For the source alternating order refer to <Selecting the Source> (page 8). [ATT] button Turns the volume down quickly. When the button is pressed again, the volume returns to the previous level.
Store unused batteries out of the reach of children. Contact a doctor immediately if the battery is accidentally swallowed.
Do not set the remote control in hot places such as above the dashboard.

Audio Control

[AUD] button Selects the Audio item to be adjusted. [VOL] buttons Adjusts the Audio item.
Refer to <Audio Control> (page 9) for the operation method, such as the procedures for Audio control and others operations.

In SIRIUS tuner source

[FM] button Selects the preset band. [4]/ [] buttons Searches up or down channels. [0] [9] buttons Press buttons [1] [6] to recall preset channels. [DIRECT]/ [OK] button Enters and cancels the <Direct Access Tuning> mode.
Refer to the instruction manual of SIRIUS Satellite radio tuner for <Direct Access Tuning> function.
[FM]/ [AM] buttons Selects the band. Each time you press the [FM] button, the band alternates between the FM1, FM2, and FM3 bands. [4]/ [] buttons Tune up or down band. [0] [9] buttons Press buttons [1] [6] to recall preset stations.
[FM] button Selects the HD FM band. Each time you press the [FM] button, the band alternates between the HF1, HF2, and HF3 bands. [AM] button Selects the HD AM band. [4]/ [] buttons Tunes up or down bands.

Cannot play an Audio file. The media is scratched or dirty. Clean the media, referring to the CD cleaning of the section on <About CDs> (page 6). The sound skips when an Audio file is being played. The media is scratched or dirty. Clean the media, referring to the CD cleaning of the section on <About CDs> (page 6). The recording condition is bad. Record the media again or use another media. The Audio file track time isnt displayed correctly. -- There are times when it isnt displayed correctly according to the Audio file recording conditions. Supreme does not take effect when it is turned ON. Little high-frequency component. Supreme would not take effect with songs with little high-frequency component. Songs that have not been encoded at bit rates lower than 96 kbps (fs = 32k, 44.1 k, 48 kHz)or those that have been encoded at a variable bit rate cannot be decoded to reproduce their highfrequency components. ---

HD Radio source

No sound can be heard, or the volume is low. The preset broadcast station is not transmitting in the mode that was set with <Receive mode Setting> (page 22). Please set <Receive mode Setting> to "AUTO". In digital AM broadcasting, receive mode switches between stereo and monaural too often. Receiving condition is bad or unstable. Stereo is chosen when receiving condition is good, and it switches to monaural when the condition becomes bad. HD Radio tuner is connected to KCA-S210A or other units. Connect the HD Radio tuner directly to the control unit.
The messages shown below display your systems condition.
EJECT: No disc magazine has been loaded in the changer. The disc magazine is not completely loaded. Load the disc magazine properly. No CD in the unit. Insert the CD. No disc has been loaded in the disc magazine. Load a disc into the disc magazine. No disc has been loaded in the disc magazine. Load a disc into the disc magazine. The CD is quite dirty. The CD is upsidedown. The CD is scratched a lot. Clean the CD and load it correctly. The CD is upside-down. Load the CD correctly. Nothing has been recorded on the MD. No tracks are recorded on the MD, although it has a title. Media was played that doesnt have data recorded that the unit can play. Use media that has data recorded that the unit can play. The faceplate of the slave unit being connected to this unit has been removed. Replace it. The unit is malfunctioning for some reason. Press the reset button on the unit. If the "E-77" code does not disappear, consult your nearest service center. Something is wrong with the disc magazine. Or the unit is malfunctioning for some reason. Check the disc magazine. And then press the reset button on the unit. If the "E-99" code does not disappear, consult your nearest service center.

The protective circuit in the unit activates when the temperature inside the automatic disc changer exceeds 60C (140F), stopping all operation. Cool down the unit by opening the windows or turning on the air conditioner. As the temperature falls below 60C (140F), the disc will start playing again. Discs are being exchanged in the Disc changer. The unit is reading the data on the disc. The CD player section is not operating properly. Reinsert the CD. If the CD cannot be ejected or the display continues to flash even when the CD has been properly reinserted, please switch off the power and consult your nearest service center. The speaker wire has a short-circuit or touches the chassis of the vehicle, and then the protection function is activated. Wire or insulate the speaker cable properly and press the reset button. An Audio file is played with a format that this unit cant support. ---A copy-protected file is played. ---The Demonstration mode has been selected. The <Demonstration mode Setting> (page 23) is ON. Turn it OFF.

NO DISC:

LOAD: READING: IN (Blink):

TOC ERR:

E-05: BLANK: NO TRACK: E-15:

PROTECT:

NA FILE:

NO PANEL:

COPY PRO: DEMO:

Specifications

Specifications subject to change without notice.

FM tuner section

Frequency range (200 kHz space) : 87.9 MHz 107.9 MHz Usable sensitivity (S/N = 30dB) : 9.3dBf (0.8 V /75 ) Quieting Sensitivity (S/N = 50dB) : 15.2dBf (1.6 V /75 ) Frequency response (3.0 dB) : 30 Hz 15 kHz Signal to Noise ratio (MONO) : 70 dB Selectivity (400 kHz) : 80 dB Stereo separation (1 kHz) : 40 dB

Audio section

Maximum output power KDC-MP2032/232MR : 50 W x 4 KDC-MP2032CR/MP232/MP202 : 45 W x 4 Full Bandwidth Power (at less than 1% THD) : 22 W x 4 Speaker impedance :4-8 Tone action Bass : 100 Hz 8 dB Middle : 1 kHz 8 dB Treble : 10 kHz 8 dB Preout level / Load (during disc play) : 2000 mV/10 k Preout impedance : 600

AM tuner section

Frequency range (10 kHz space) : 530 kHz 1700 kHz Usable sensitivity (S/N = 20dB) : 28 dB (25 V)
Operating voltage (11 16V allowable) : 14.4 V Current consumption : 10 A Installation Size (W x H x D) : 182 x 53 x 155 mm 7-3/16 x 2-1/16 x 6-1/8 inch Weight : 3.1 lbs (1.40 kg)

CD player section

Laser diode : GaAlAs Digital filter (D/A) : 8 Times Over Sampling D/A Converter : 1 Bit Spindle speed KDC-MP2032/MP2032CR/MP232/MP202 : rpm (CLV 2times) KDC-232MR : rpm (CLV) Wow & Flutter : Below Measurable Limit Frequency response (1 dB) : 10 Hz 20 kHz Total harmonic distortion (1 kHz) : 0.01 % Signal to Noise ratio (1 kHz) KDC-MP2032/MP2032CR/MP232/MP202 : 105 dB KDC-232MR: 93 dB Dynamic range : 93 dB MP3 decode KDC-MP2032/MP2032CR/MP232/MP202 : Compliant with MPEG-1/2 Audio Layer-3 WMA decode KDC-MP2032/MP2032CR/MP232/MP202 : Compliant with Windows Media Audio