Before using this unit for the first time
This unit is initially set on the Demonstration mode. When using this unit for the first time, cancel the <Demonstration mode Setting> (page 12).

How to reset your unit

If the unit fails to operate properly, press the Reset button. The unit returns to factory settings when the Reset button is pressed. Press the reset button if the disc auto changer fails to operate correctly. Normal operation should be restored.

Handling CDs

Reset button

Cleaning the Unit

If the faceplate of this unit is stained, wipe it with a dry soft cloth such as a silicon cloth. If the faceplate is stained badly, wipe the stain off with a cloth moistened with neutral cleaner, then wipe it again with a clean soft dry cloth.
Do not touch the recording surface of the CD. Do not stick tape etc. on the CD, or use a CD with tape stuck on it. Do not use disc type accessories. Clean from the center of the disc and move outward. When removing CDs from this unit, pull them out horizontally. If the CD center hole or outside rim has burrs, use the CD only after removing the burrs with a ballpoint pen etc.

CDs that cannot be used

CDs that are not round cannot be used.
Applying spray cleaner directly to the unit may affect its mechanical parts. Wiping the faceplate with a hard cloth or using a volatile liquid such as thinner or alcohol may scratch the surface or erases characters.
Cleaning the Faceplate Terminals
If the terminals on the unit or faceplate get dirty, wipe them with a clean soft dry cloth.

Lens Fogging

When you turn on the car heater in cold weather, dew or condensation may form on the lens in the CD player of the unit. Called lens fogging, this condensation on the lens may not allow CDs to play. In such a situation, remove the disc and wait for the condensation to evaporate. If the unit still does not operate normally after a while, consult your Kenwood dealer.
. This unit may not correctly play discs which do not have the mark. You cannot play a CD-R or CD-RW that has not been finalized. (For the finalization process refer to your CD-R/CD-RW writing software, and your CD-R/CDRW recorder instruction manual.)

During reception of stereo stations the ST indicator is ON.
Traffic information : [FM+] Turns ON or OFF the Traffic Information function when pressing for at least 2 seconds. When the function is turned ON, TI indicator is ON. If traffic bulletin starts when the function is ON, TRAFFIC is displayed and traffic information is received.
If the volume is adjusted during reception of traffic information, the adjusted volume is memorized automatically. The memorized volume will be applied next time the Traffic Information function is turned ON.
Preset memory : [1] - [6] Memorize the station selected when pressing for at least 2 seconds. Preset tuning : [1] - [6] Recalls the memorized station.

Disc play functions

Disc play : Disc slot Starts playing when a disc is inserted. When a CD is inserted, the IN indicator is ON.
Scrolls the tuner, CD and audio file text display when pressed for at least 1 second.
3 inch (8 cm) CD cannot be used. Attempt to insert using an adapter can cause malfunction. Refer to <About Audio file> (page 13) for the Audio file by models you can play.
Pause and play : [6] Switches between pause and play each time this button is pressed.
Audio Control 1 Select the source to adjust

Press the [SRC] button.

Volume offset: Sets each sources volume as a difference from the basic volume.
2 Enter Audio Control mode

Press the [AUD] knob.

4 Adjust the Audio setup item

Turn the [AUD] knob.

3 Select the Audio item to adjust
Press the [AUD] knob. Adjustment Item Display Subwoofer level SW L Bass Boost B.BOOST/B.B Range 15 +15 1/2/OFF (The indicator turns on according to the setting.) Natural/Rock/Pops/Easy/ Top 40/Jazz/Game/User setting

5 Exit Audio Setup mode

Press the [AUD] knob for at least 1 second.

Speaker Setting

Fine-tuning so that the System Q value is optimal when setting the speaker type.

System Q

NATURAL/ ROCK/ POPS/ EASY/ TOP40/ JAZZ/ GAME/ USER Bass level BAS L 8 +8 Middle level MID L 8 +8 Treble level TRE L 8 +8 Balance BAL Left 15 Right 15 Fader FAD Rear 15 Front 15 Exit Audio Control mode (Volume control mode)

1 Enter Standby

Press the [SRC] button. Select the STANDBY display.
2 Enter Speaker Setting mode
USER: This appears when Bass level, Middle level, and Treble level are adjusted. When USER is selected, these levels are recalled.

4 Adjust the Audio item

5 Exit Audio Control mode
Press the [AUD] knob. Turn the [AUD] knob. Speaker type OFF For 5 & 4 in. speaker For 6 & 6x9 in. speaker For the OEM speaker
3 Select the Speaker type
Display SP OFF SP 5/4 SP 6*9/6 SP OEM
4 Exit Speaker Setting mode
Press any button. Press a button other than the [AUD] knob.

Switching Display

Changes displayed information on each source following;

Audio Setup

Setting the Sound system.

In Tuner source

Information Program Service name or Frequency Radio text, Program Service name or Frequency Clock Display FREQ/ FREQ/PS R-TEXT CLOCK
1 Select the source to adjust

2 Enter Audio Setup mode

3 Select the Audio Setup item to adjust
Press the [AUD] knob. Adjustment Item Display Low Pass Filter LPF Volume offset V-OFF Range 80/120/160/Through(OFF) Hz (AUX: -8 +8)
In CD & External disc source
Information Disc title Track title Play time & Track number Clock Display D-TITLE T-TITLE P-TIME CLOCK

In Audio file source

Information Music title & Artist name Album name & Artist name Folder name File name Play time & Music number Clock Display TITLE ALBUM FOLDER FILE P-TIME CLOCK
In Standby/ Auxiliary input source
Information Source name Clock Display SRC NAME CLOCK
When you select the clock display, the display setting of each source will be changed to the clock display. Album name cannot be displayed in WMA file. If the selected display item does not have any information, alternative information is displayed.
Manual Clock Adjustment 1 Select the Clock display

Press the [DISP] button.

2 Enter Clock Adjust mode
Press the [DISP] button for at least 1 second. The clock display blinks.

3 Adjust the hours

Press the [FM+] or [AM] button. Adjust the minutes Press the [4] or [] button.
4 Exit Clock adjustment mode
You can do this adjustment when the SYNC of the <Menu System> (page 10) is set as OFF.

PTY (Program Type)

Selecting the Program Type and searching for a station.
3 Search for the selected Program Type station
Press the [4] or [] button.
When the selected Program Type is not found, NO PTY is displayed. Select another Program Type.

1 Enter PTY mode

Press the Search button. During PTY mode the PTY indicator is ON.

4 Exit PTY mode

Press the Search button.
This function cannot be used during a traffic bulletin or AM reception.
2 Select the Program Type
Press the [FM+] or [AM] button. No. 1 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 28. 29. 30. 31. Program Type Speech Music News Current Affairs Information Sport Education Drama Culture Science Varied Pop Music Rock Music Easy Listening Music Light Classical Serious Classical Other Music Weather Finance Childrens programs Social Affairs Religion Phone In Travel Leisure Jazz Music Country Music National Music Oldies Music Folk Music Documentary Display SPEECH MUSIC NEWS AFFAIRS INFO SPORT EDUCATE DRAMA CULTURE SCIENCE VARIED POP M ROCK M EASY M LIGHT M CLASSICS OTHER M WEATHER FINANCE CHILDREN SOCIAL RELIGION PHONE IN TRAVEL LEISURE JAZZ COUNTRY NATION M OLDIES FOLK M DOCUMENT

Program Type preset

Putting the Program Type in the Preset button memory and quick recall.
Presetting the Program Type
1 Select the Program Type to preset
Refer to <PTY (Program Type)>.
2 Preset the Program Type
Press the desired [1] [6] button for at least 2 seconds.
Recalling the preset Program Type
Refer to <PTY (Program Type)>. Press the desired [1] [6] button.
2 Recall the Program Type
Changing Language for PTY Function
Selecting the Program Type display language.
2 Enter Changing Language mode

3 Select the language

Press the [FM+] or [AM] button. Language English French German Display ENGLISH FRENCH GERMAN
Speech and Music include the Program type shown below. Music: No.12 17, Speech: No.3 11, 18 25, 31
4 Exit Changing Language mode
Music disc/Audio le Operation
Music Search (Function of Audio file)
Search for the song you want to listen to by tracing the media file structure.
Music Search (Function of Music CD)
Select the song you want to listen to by turning the [AUD] knob.
1 Enter Music Search mode
Press the Search button. SEARCH is displayed. Displays the current Audio file name.
Press the Search button. SEARCH is displayed. Displays the current music No.
2 Searching for and playing a song
Operation type Movement between folders/files Selection of folder/flie Return to previous folder Return to root folder Operation Turn the [AUD] knob, or press the [FM+]/[AM] button. Press the [AUD] knob or [] button. Press the [4] button. Press the [4] button for at least 1 second.

2 Select the music

3 Play the selected song
Press the [AUD] knob. The Music Search mode is canceled and the selected song is played.
(ON) : Indicates that a folder exists above the currently selected folder. (OFF) : Indicates that no folder exists above the currently selected folder. (ON) : Indicates that a folder exists under the currently selected folder. (Blinking) : Indicates that your selection is a file.
Returning to the first song Press the [4] button for at least 1 second. Cancelling the Music Search mode Press the Search button.
Cancelling the Music Search mode Press the Search button.
Music Search cannot be performed during Random play or scan play.
Music Search is available only during playing of the builtin CD player. Music Search cannot be performed during Random play or scan play.

Menu System

Setting various functions. Display SCL AUX OFF Setting AUTO/ MANU* OFF/ON1*/ ON2 OFF 60M Setting overview Specifies whether the text is scrolled automatically. Sets whether to display AUX during source selection. Turns off the power when the preset time has lapsed in the Standby mode. Sets the CD read mode. Specifies whether to enable demonstration. Source

1 Enter Menu mode

Press the Search button for at least 1 second. MENU is displayed.

2 Select the Menu item

Press the [FM+] or [AM] button. Display Setting Setting overview Source CODE SET/ Refer to Sets/Resets security code. CODE CLR page 11 (Function of KDC-W3544W) SYNC ON*/OFF Synchronizing the RDS station time data and this units clock. DIM ON/OFF* Adjusts the brightness of the display according to the surrounding illumination. ICON ON1/ON2*/ Sets the Graphics mode of the OFF display. SWPRE R*/ SW Sets the preout output. SPRM ON*/OFF Turns ON/OFF the Supreme function. NEWS OFF* Turns ON/OFF the News Bulletin 90M Automatic Reception function and sets the news bulletin interrupt disabled time. LO.S ON/OFF* Only stations whose reception is good are searched in auto seek tuning. AUTO1*/ Selects the tuning mode of AUTO1/ the radio. AUTO2/ AUTO2/ MANUAL MANUAL A-MEMORY Refer to Memorizes six stations with good page 12 reception automatically. AF ON*/OFF When station reception is poor, automatically switches to the station that is broadcasting the same program over the same RDS network. REG ON*/OFF Sets whether to switch to the station only in the specific region using the AF control. ATPS ON*/OFF When traffic information station reception is poor, automatically searches for a station that can be received better. MONO ON/OFF* Receives a stereo broadcast in the mono mode. NAME SET Refer to Sets the display when switched page 12 to AUX source. RUS*1 ON*/OFF Selects Russian as the display language.

3 Select Security Code mode
4 Enter Security Code mode
5 Select the digits to enter 6 Select the Security Code numbers
Press the [FM+] or [AM] button.
8 Do the step 4 through 7 operation, and reenter
the Security Code. APPROVED is displayed. The Security Code function activates.
7 Repeat steps 4 and 5, and complete the

Security Code.

If you enter the wrong Code in steps 4 through 6, repeat from step 4.
8 Press the [AUD] knob for at least 3 seconds.
CLEAR is displayed. The Security Code function deactivates.
9 Exit Security Code mode
Resetting the Security Code function when the audio unit is first used after removed from the battery power source or the Reset button is pressed
If a wrong security code is entered, ERROR is displayed. Enter a correct security code.

1 Turn the power ON.

Auto memory entry 1 Enter Menu mode
The Auxiliary input display can be set only when the built-in auxiliary input or the auxiliary input of optional KCA-S220A is used. On the KCA-S220A, AUX EXT is displayed by default.
2 Select the Auto memory mode
Press the [FM+] or [AM] button. Select the A-MEMORY display.
Demonstration mode Setting
Sets the demonstration mode.
3 Enter the Auto memory mode
Press the [AUD] knob for at least 2 seconds.
2 Select the Demonstration mode Auxiliary Input Display Setting
Selecting the display when changing to Auxiliary input source. Press the [FM+] or [AM] button. Select the DEMO display.
3 Set the Demonstration mode
Press the [AUD] knob for at least 2 seconds. Each time you press the knob at least 2 seconds, the Demonstration mode alternates between the settings shown in the table below. Display DEMO ON DEMO OFF Setting The Demonstration mode function is ON. Exit Demonstration mode (Normal mode).
1 Select Auxiliary input source
Press the [SRC] button. Select the AUX display.
3 Select Auxiliary input display setting mode
Press the [FM+] or [AM] button. Select the NAME SET display.
4 Enter Auxiliary input display setting mode
Press the [AUD] knob for at least 1 second. The presently selected Auxiliary input display is displayed.
5 Select the Auxiliary input display

Press the [4] or [] button. Each time you push the knob, the display alternates as listed below. AUX DVD PORTABLE GAME VIDEO TV
6 Exit Auxiliary input display setting mode
When operation stops for 10 seconds, the name at that time is registered, and the Auxiliary input display setting mode closes.

About Audio file

Playable Audio file MP3 (.mp3), WMA (.wma) Playable disc media CD-R/RW/ROM Playable disc file format ISO 9660 Level 1/2, Joliet, Romeo, Long file name. Although the audio files are complied with the standards listed above, the play maybe impossible depending on the types or conditions of media or device. Playing order of the Audio file In the example of folder/file tree shown below, the files are played in the order from to.
: Folder Folder : Audio file Audio fi
An online manual about audio files is put on the site, www.kenwood.com/audiofile/. On this online manual, detailed information and notes which are not written in this manual are provided. Make sure to read through the online manual as well.

Menu Glossary

SWPRE (Switching Preout) Switches the preout between rear output (R) and subwoofer output (SW). SPRM (Supreme) Technology to extrapolate and supplement with proprietary algorithm, the high-frequency range that is cut off when encoding at low bit rate. Supplementing is optimized by compression format (MP3 or WMA) and processed according to bit rate. The effect is negligible with music that is encoded at high bit rate, variable bit rate or has minimal high frequency range. CD READ Sets the method for reading CD. When unable to play special format CD, set this function to 2 to force playing. Note that some music CD may be unplayable even when set to 2. In addition, audio files cannot be played when set to 2. Normally, keep this set to 1. 1 : Automatically distinguishes between audio file disc and music CD when playing disc.

Manual

2 : Forces playing as music CD. AUX When this is set to ON, AUX source can be selected. ON1: Outputs the sound of external unit connected to the AUX terminal when switched to AUX source. ON2: Activates the attenuator function when switched to AUX source. Turn off the attenuator function when listening to output from external unit. This prevents the noise when no external unit is connected to AUX terminal. OFF: Disables the selection of AUX source. Set to OFF when not using the AUX terminal. NEWS (News Bulletin with Timeout Setting) Automatically receives news bulletin when it starts. Set the time during which interrupt is to be disabled after start of another news bulletin. Changing NEWS 00M to NEWS 90M turns this function ON. If news bulletin starts when this function is ON, TRAFFIC is displayed and news is received. If 20M is has been set, reception of another news bulletin will not start for 20 minutes. AUTO1, AUTO2, MANUAL (Tuning mode select) Select a tuning mode of the radio. Tuning mode Display Auto seek AUTO1 Preset station seek AUTO2

Operation Automatic search for a station. Search in order of the stations in the Preset memory. MANUAL Normal manual tuning control.
AF (Alternative Frequency) When the reception is poor, automatically alternate to another frequency broadcasting the same program in the same RDS network with better reception. RUS (Russian language setting) When this is set to ON, the following character strings are displayed in Russian: Folder name/ File name/ Song title/ Artist name/ Album name/ KCA-BT200/BT100 (optional accessory)
OFF (Power OFF Timer) Setting the timer to turn this units power OFF automatically when Standby mode continues. Using this setting can save the vehicles battery power. : Power OFF Timer function is OFF. 20M: Turns the power OFF after 20 minutes. (Factory setting) 40M: Turns the power OFF after 40 minutes. 60M: Turns the power OFF after 60 minutes. ICON Sets the Graphics mode of the display during normal playback condition. ON1: Turns on. ON2: Displays an animation. OFF: Turns off. This Product is not installed by the manufacturer of a vehicle on the production line, nor by the professional importer of a vehicle into an EU Member State.
Information on Disposal of Old Electrical and Electronic Equipment and Batteries (applicable for EU countries that have adopted separate waste collection systems)
Products and batteries with the symbol (crossed-out wheeled bin) cannot be disposed as household waste. Old electrical and electronic equipment and batteries should be recycled at a facility capable of handling these items and their waste byproducts. Contact your local authority for details in locating a recycle facility nearest to you. Proper recycling and waste disposal will help conserve resources whilst preventing detrimental effects on our health and the environment. Notice: The sign Pb below the symbol for batteries indicates that this battery contains lead.
For operating KCA-BT200 (optional)
For operation refer to Model-A-1 in the Instruction Manual of KCA-BT200, and the table below. The [AUTO]/[TI] button should be replaced with [SRC] button for <Answering the Waiting Call after Terminating the Current Call>. Notation used in the KCA-BT200 Instruction Manual [38] button Control knob [AUTO]/[TI] button Control knob towards up or down Control knob towards left or right Operation
For operating KCA-BT100 (optional)
To control KCA-BT100, operate as follows; To make setting for <Selecting the Dialing Mode>, select <Menu System> (page 10). Pressing the [AUD] knob for at least 1 second after selecting the "D.MODE" item allows you to enter the dialing method selection mode. To exit from dialing method selection mode, press Search button. To make <Disconnecting a Call>, <Clearing the Disconnection Message>, and <Rejecting an Incoming call>, press [DISP] button for at least 1 second. Moreover, some displays are different from the description of KCA-BT100 Instruction Manual. Displays of KCA-BT100 Instruction Manual DISCONCT CONNECT PHN-DEL P-STATUS BT-CON Y BT-CON N Actual displays on this unit HF D-CON HF CON DVC-DEL D-STATUS HF-CON Y HF-CON N

[AUD] knob [AUD] knob [DISP] button [FM+] or [AM] button [4] or [] button
The marking of products using lasers (Except for some areas)

CLASS 1 LASER PRODUCT

The label is attached to the chassis/case and says that the component uses laser beams that have been classified as Class 1. It means that the unit is utilizing laser beams that are of a weaker class. There is no danger of hazardous radiation outside the unit.
Accessories/ Installation Procedure

Accessories

with the ignition, connect the ignition wire to a power source that can be turned on and off with the ignition key. Use a commercially available conversion connector if the connector does not fit in the vehicle connector. Insulate unconnected wires with vinyl tape or other similar material. To prevent a short circuit, do not remove the caps on the ends of the unconnected wires or the terminals. If the console has a lid, make sure to install the unit so that the faceplate will not hit the lid when closing and opening. If the fuse blows, first make sure the wires arent touching to cause a short circuit, then replace the old fuse with one with the same rating. Connect the speaker wires correctly to the terminals to which they correspond. The unit may be damaged or fail to work if you share the - wires or ground them to any metal part in the car. After the unit is installed, check whether the brake lamps, blinkers, wipers, etc. on the car are working properly. Mount the unit so that the mounting angle is 30 or less.
2..2 Installation Procedure
1. To prevent short circuits, remove the key from the ignition and disconnect the - terminal of the battery. 2. Make the proper input and output wire connections for each unit. 3. Connect the wire on the wiring harness. 4. Take Connector B on the wiring harness and connect it to the speaker connector in your vehicle. 5. Take Connector A on the wiring harness and connect it to the external power connector on your vehicle. 6. Connect the wiring harness connector to the unit. 7. Install the unit in your car. 8. Reconnect the - terminal of the battery. 9. Press the reset button.

About CD players/disc changers connected to this unit
If the CD player/ disc changer has the O-N switch, set it to the N position. The functions you can use and the information that can be displayed may differ depending on the models being connected.
Mounting and wiring this product requires skills and experience. For safetys sake, leave the mounting and wiring work to professionals. Make sure to ground the unit to a negative 12V DC power supply. Do not install the unit in a spot exposed to direct sunlight or excessive heat or humidity. Also avoid places with too much dust or the possibility of water splashing. Do not use your own screws. Use only the screws provided. If you use the wrong screws, you could damage the unit. If the power is not turned ON (PROTECT is displayed), the speaker wire may have a short-circuit or touched the chassis of the vehicle and the protection function may have been activated. Therefore, the speaker wire should be checked. Make sure that all wire connections are securely made by inserting jacks until they lock completely. If your vehicles ignition does not have an ACC position, or if the ignition wire is connected to a power source with constant voltage such as a battery wire, the power will not be linked with the ignition (i.e., it will not turn on and off along with the ignition). If you want to link the units power
Connecting Wires to Terminals
To Kenwood disc changer/ External optional accessory (KDC-W3544W only)

Fuse (10A)

Rear preout/ Subwoofer preout

FM/AM antenna input

Antenna Cord (JASO) Wiring harness (Accessory1)

TEL mute wire (Brown)

Power control/ Motor antenna control wire (Blue/White)
If no connections are made, do not let the wire come out from the tab.

MUTE P.CONT ANT.CONT

Connect to the terminal that is grounded when either the telephone rings or during conversation.
To connect the Kenwood navigation system,
consult your navigation manual.
Connect either to the power control terminal when using the optional power amplifier, or to the antenna control terminal in the vehicle.
Battery wire (Yellow) Ignition wire (Red)

See next page.

A7 Pin (Red) A4 Pin (Yellow)

Connector A

Connector B

Connector Function Guide

Pin Numbers for ISO Connectors External Power Connector A-4 A-5 A-7 A-8 Speaker Connector B-1 B-2 B-3 B-4 B-5 B-6 B-7 B-8 Cable Colour Functions
2WARNING Connecting the ISO Connector
The pin arrangement for the ISO connectors depends on the type of vehicle you drive. Make sure to make the proper connections to prevent damage to the unit. The default connection for the wiring harness is described in 1 below. If the ISO connector pins are set as described in 2, make the connection as illustrated. Please be sure to reconnect the cable as shown 2 below to install this unit to the Volkswagen vehicles etc.

Cannot display the user of System Q. <Audio Control> (page 6) is not set. Cannot set up the subwoofer. No output from the subwoofer. Cannot set up the low pass filter. Preout is not set to subwoofer. SWPRE of <Menu System> (page 10) <Subwoofer output> (page 4) is not set to On. Cannot register a security code. Cannot set up Display. Power OFF Timer does not function. <Demonstration mode Setting> (page 12) is not turned off.

E-05: E-15: E-77:

What might seem to be a malfunction in your unit may just be the result of slight misoperation or miswiring. Before calling service, first check the following table for possible problems.

IN (Blink):

Tuner source
Radio reception is poor. The car antenna is not extended. Pull the antenna out all the way.

Disc source

The specified disc does not play, but another one plays instead. The specified CD is quite dirty. Clean the CD referring to the CD cleaning of the section on <Handling CDs> (page 3). The disc is loaded in a different slot from that specified. Eject the disc magazine and check the number for the specified disc. The disc is severely scratched. Try another disc instead.
PROTECT: NA FILE: COPY PRO:
The CD player section is not operating properly. Reinsert the CD. If the CD cannot be ejected or the display continues to flash even when the CD has been properly reinserted, please switch off the power and consult your nearest service center. The speaker wire has a short-circuit or touches the chassis of the vehicle, and then the protection function is activated. Wire or insulate the speaker cable properly and press the reset button. If the PROTECT code does not disappear, consult your nearest service center. An Audio file is played with a format that this unit cant support. ----
A copy-protected file is played. ----

Audio file source

The sound skips when an Audio file is being played. The media is scratched or dirty. Clean the media, referring to the CD cleaning of the section on <Handling CDs> (page 3). The recording condition is bad. Record the media again or use another media.

Specications

FM tuner section
Frequency range (50 kHz space) : 87.5 MHz 108.0 MHz Usable sensitivity (S/N = 26dB) : 0.7 V/75 Quieting Sensitivity (S/N = 46dB) : 1.6 V/75 Frequency response (3.0 dB) : 30 Hz 15 kHz Signal to Noise ratio (MONO) : 65 dB Selectivity (DIN) (400 kHz) : 80 dB Stereo separation (1 kHz) : 35 dB

Audio section

Maximum output power : 50 W x 4 Output power (DIN 45324, +B=14.4V) : 30 W x 4 Speaker Impedance :48 Tone action Bass : 100 Hz 8 dB Middle : 1 kHz 8 dB Treble : 10 kHz 8 dB Preout level / Load (CD) : 2000 mV/10 k Preout impedance : 600

MW tuner section

Frequency range (9 kHz space) : 531 kHz 1611 kHz Usable sensitivity (S/N = 20dB) : 25 V

Auxiliary input

Frequency response (3 dB) : 20 Hz 20 kHz Input Maximum Voltage : 1200 mV Input Impedance : 10 k

LW tuner section

Frequency range : 153 kHz 281 kHz Usable sensitivity (S/N = 20dB) : 45 V

CD player section

Laser diode : GaAlAs Digital filter (D/A) : 8 Times Over Sampling D/A Converter : 24 Bit Spindle speed : rpm (CLV) Wow & Flutter : Below Measurable Limit Frequency response (1 dB) : 20 Hz 20 kHz Total harmonic distortion (1 kHz) : 0.01 % Signal to Noise ratio (1 kHz) : 105 dB Dynamic range : 93 dB MP3 decode : Compliant with MPEG-1/2 Audio Layer-3 WMA decode : Compliant with Windows Media Audio

General

Operating voltage (11 16V allowable) : 14.4 V Current consumption : 10 A Installation Size (W x H x D) : 182 x 53 x 155 mm Weight : 1.30 kg
Specifications subject to change without notice.