Before using this unit for the first time
This unit is initially set on the Demonstration mode. When using this unit for the first time, cancel the <Demonstration mode Setting> (page 25).
About DAB Tuner control (KDC-W4534)
Reset button The characters which can be displayed by this unit are A-Z 0-9 @ " ` % & * + = ,. / \ < > [ ] ( ) : ; ^-{}|~. The RDS feature wont work where the service is not supported by any broadcasting station. The illustrations of the display and the panel appearing in this manual are examples used to explain more clearly how the controls are used. Therefore, what appears on the display in the illustrations may differ from what appears on the display on the actual equipment, and some of the illustrations on the display may be inapplicable.
Refer to A group on the Instruction manual of DAB Tuner KTC-9090DAB (optional accessory) for the control method of DAB Tuner function. However, the following control methods of the function for this unit may be differed from the Instruction manual; therefore, refer to the following supplemental instruction. <Auto Ensemble Memory Entry> 1. Select the preset band for Auto Ensemble Memory Entry. 2. Press the [AME] button for at least 2 seconds. Open Auto Ensemble Memory Entry. After storing in the memory finishes, the number of the pre-set buttons and the ensemble label are displayed. <Searching by programme type and language> and <Languages to be displayed> in <Programme Type (PTY) Function> At the operation to press [DISP] button, use [TI] button instead.

Cleaning the Unit

If the faceplate of this unit is stained, wipe it with a dry soft cloth such as a silicon cloth. If the faceplate is stained badly, wipe the stain off with a cloth moistened with neutral cleaner, then wipe it again with a clean soft dry cloth.
Applying spray cleaner directly to the unit may affect its mechanical parts. Wiping the faceplate with a hard cloth or using a volatile liquid such as thinner or alcohol may scratch the surface or erases characters.
Cleaning the Faceplate Terminals
If the terminals on the unit or faceplate get dirty, wipe them with a clean soft dry cloth.

Limitation of structure for the file and the folder
Maximum number of directory levels: 8 Maximum number of folders: 100 Maximum number of files per folder: 255
Playing order of the Audio file
The Audio file plays in the order which is written by writing software. You may be able to set the playing order by writing the play sequence numbers such as "01" to "99" at the beginning of the file name. Example 0: Folder CD (1) : Audio file

Playable MP3 file

MPEG 1/2 Audio Layer 3 file Transfer bit rate: 8-320 kbps Sampling frequency : 8, 11.025, 12, 16, 22.05, 24, 32, 44.1, 48 kHz

" 3

Playable WMA file
The file in accordance with Windows Media Audio (Except for the file for Windows Media Player 9 or after which applies the new functions) Transfer bit rate: 48-192 kbps Sampling frequency: 32, 44.1, 48 kHz

Playable media

CD-ROM, CD-R, CD-RW
CD-RW discs which are quick formatted by the writing software cannot be used. When recording to the maximum media capacity at once, the writing software is set to "Disc at once".

Playable disc format

ISO 9660 Level 1/2 Joliet Romeo Long file name.
Playing order Playing order after ! play. ", #, $, %. File search Forward file search during # play. Push the Control knob towards [] $ Folder search Forward folder search during " play. Push the Control knob towards [FM] 3, 4. Folder select When the selection is set to directory 4, and you want to skip to the folder 2 at the same level. Push the Control knob towards [4] 2 When the selection is set to directory 3, moves the level up by folder select. Push the Control knob towards [AM] 2

About CDs

Handling CDs
Do not touch the recording surface of the CD.

Removing CDs

When removing CDs from this unit pull them out horizontally.

CDs that cannot be used

CDs that are not round cannot be used.
CD-R and CD-RW are easier to damage than a normal music CD. Use a CD-R or a CD-RW after reading the caution items on the package etc. Do not stick tape etc. on the CD, or use a CD with tape stuck on it.

When using a new CD

If the CD center hole or outside rim has burrs, use the CD only after removing the burrs with a ballpoint pen, etc.
CDs with coloring on the recording surface or CDs that are dirty cannot be used. This unit can only play the CDs with. This unit may not correctly play discs which do not have the mark. You cannot play a CD-R or CD-RW that has not been finalized. (For the finalization process refer to your CD-R/CD-RW writing software, and your CDR/CD-RW recorder instruction manual.)

Burrs Burrs

CD storage
Do not place CDs in direct sunlight (On the seat or dashboard etc.) or where the temperature is high. Store CDs in their cases.

CD accessories

Do not use disc type accessories.

CD cleaning

Clean from the center of the disc and move outward.

General features

Release button

Control knob

ATT/DIM

LOUD indicator

ATT indicator

Clock display

Turning ON the Power Press the [SRC] button. Turning OFF the Power Press the [SRC] button for at least 1 second.
The time until full power OFF can be set in <Power OFF Timer> (page 25).

Volume

Increasing Volume Turn the [VOL] knob clockwise.

Selecting the Source

Press the [SRC] button. Source required Tuner CD External disc* (Optional accessory) Auxiliary input* Standby (Illumination only mode) Display "TUNER" "CD" "CD CH" "AUX EXT" "STANDBY"
Decreasing Volume Turn the [VOL] knob counterclockwise.

Attenuator

Turning the volume down quickly. Press the [ATT] button. Each time you press the button, the Attenuator turns ON and OFF. When the Attenuator is ON, the "ATT" indicator blinks.
* Function of the KDC-W4534 This unit automatically turns full power OFF after 20 minutes lapses in Standby mode in order to save the vehicle's battery.

System Q

Selecting the best sound setting preset for different types of music.
1 Select the source to set

Press the [SRC] button.

2 Select the Sound type
Press the [Q] button. When you press the button once, the current sound setting is displayed. Each time you press the button, the sound setting alternates. Sound setting Natural Rock Pops Easy Top 40 Jazz Display "NATURAL" "ROCK" "POPS" "EASY" "TOP40" "JAZZ"
Adjustment Item Display Range Bass level "BAS L" 8 +8 Middle level "MID L" 8 +8 Treble level "TRE L" 8 +8 Balance "BAL" Left 15 Right 15 Fader "FAD" Rear 15 Front 15 Exit Audio Control mode (Volume control mode)
5 Exit Audio Control mode
Press any button. Press a button other than the [VOL] knob, [SRC], [0] and [ATT] button.

Audio Setup

Function of the KDC-W434A/G/KDC-W40G/KDCW434GY

Tuning Mode

Choose the tuning mode. Press the [AUTO] button. Each time you press the button, the Tuning mode alternates between the modes shown in the table below. Tuning mode Display Operation Auto seek "AUTO 1" Automatic search for a station. Preset station seek "AUTO 2" Search in order of the stations in the Preset memory. Manual "MANUAL" Normal manual tuning control.

1 Select tuner source

Press the [SRC] button. Select the "TUNER" display.

2 Select the band

Push the Control knob towards [FM] or [AM]. Each time you push the knob toward [FM], it switches between the FM1, FM2, and FM3 bands.

3 Tune up or down band

During reception of stereo stations the "ST" indicator is ON.

Station Preset Memory

Putting a station in the memory.

1 Select the band

Push the Control knob towards [FM] or [AM].
2 Select the frequency to put in the memory
3 Put the frequency in the memory
Press the desired [1] [6] button for at least 2 seconds. The preset number display blinks 1 time. On each band, 1 station can be put in the memory on each [1] [6] button.

Auto Memory Entry

Putting stations with good reception in the memory automatically.
1 Select the band for Auto Memory Entry

2 Open Auto Memory Entry

Press the [AME] button for at least 2 seconds. When 6 stations that can be received are put in the memory Auto Memory Entry closes.
When the <AF (Alternative Frequency)> (page 23) is ON, only RDS stations are put in the memory. When Auto Memory Entry is done in the FM2 band, the RDS stations preset in the FM1 band are not put in the memory. Likewise, when Auto Memory Entry is done in the FM3 band, RDS stations preset in FM1 or FM2 are not put in the memory.

Preset Tuning

Recalling the stations in the memory.

2 Recall the station

Press the desired [1] [6] button. English |
Function of the KDC-W4534/KDC-W4034A/AY/G/GY/KDC-3034A/G/KDC-W410A/AY/G/GY

PTY indicator

TI indicator

Traffic Information

Changing to traffic information automatically when a traffic bulletin starts even when you are not listening to the radio. Press the [TI] button. Each time you press the button, the Traffic information function turns ON and OFF. When traffic information is ON, "TI" indicator is ON. When a traffic information station is not being received the "TI" indicator blinks. When a traffic bulletin starts, "TRAFFIC" is displayed and the audio changes to traffic information.

During reception of an AM station when the Traffic Information function is turned ON, the frequency changes to an FM station. During reception of traffic information the adjusted volume is automatically remembered, and the next time the audio changes to traffic information, the volume automatically becomes the remembered volume.
Receiving other traffic information stations Push the Control knob towards [4] or [].
Traffic information can be switched when it is on the Tuner Source. However, you cannot switch the Traffic information during reception of the Traffic bulletin switched from the source other than the Tuner.
Function of the KDC-W4534

Radio Text Scroll

Scrolling the displayed radio text. Hold down on [FM] of the Control knob for at least 2 seconds.

PTY (Program Type)

Selecting the Program Type and searching for a station.
Speech and Music include the Program type shown below. Music: No.12 17, Speech: No.3 11, 18 25, 31 You can put the Program Type in the [1] [6] button memory and for quick recall. Refer to the <Program Type preset> (page 15). You can change the display language. Refer to <Changing Language for PTY Function> (page 16).

1 Enter PTY mode

Press the Control knob. During PTY mode the "PTY" indicator is ON.
This function cannot be used during a traffic bulletin or AM reception.
2 Select the Program Type
Push the Control knob towards [FM] or [AM]. Each time you push the knob, the Program Type alternates between the program types shown in the table below. No. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 28. 29. 30. 31. Program Type Speech Music News Current Affairs Information Sport Education Drama Culture Science Varied Pop Music Rock Music Easy Listening Music Light Classical Serious Classical Other Music Weather Finance Childrens programs Social Affairs Religion Phone In Travel Leisure Jazz Music Country Music National Music Oldies Music Folk Music Documentary Display "SPEECH" "MUSIC" "NEWS" "AFFAIRS" "INFO" "SPORT" "EDUCATE" "DRAMA" "CULTURE" "SCIENCE" "VARIED" "POP M" "ROCK M" "EASY M" "LIGHT M" "CLASSICS" "OTHER M" "WEATHER" "FINANCE" "CHILDREN" "SOCIAL" "RELIGION" "PHONE IN" "TRAVEL" "LEISURE" "JAZZ" "COUNTRY" "NATION M" "OLDIES" "FOLK M" "DOCUMENT"

3 Enter Security Code mode
Press the Control knob for at least 2 seconds. When "ENTER" is displayed, "CODE" is also displayed.
Number of times the incorrect code was input 3 4
Input prohibited time 5 minutes 1 hour 24 hours

In Standby mode

4 Select the digits to enter

Touch Sensor Tone

Setting the operation check sound (beep sound) ON/OFF. Display "BEEP ON" "BEEP OFF" Setting Beep is heard. Beep canceled.
5 Select the Security Code numbers
6 Repeat steps 4 and 5, and complete the

Security Code.

7 Confirm the Security Code
Press the Control knob for at least 3 seconds. When "RE-ENTER" is displayed, "CODE" is also displayed.
8 Do the step 4 through 7 step operation, and
reenter the security code. "APPROVED" is displayed. The Security Code function activates.
In Standby mode Function of the KDC-W4534

Manual Clock Adjustment

You can do this adjustment when the <Synchronize Clock> (page 22) is set as OFF.

Selectable Illumination

Selecting the button illumination color as green or red. Display "KEY RED" "KEY GRN" Setting The illumination color is red. The illumination color is green.
1 Select Clock Adjustment mode
Push the Control knob towards [FM] or [AM]. Select the "CLK ADJ" display.
2 Enter Clock Adjust mode
Press the Control knob for at least 1 second. The clock display blinks.

3 Adjust the hours

Push the Control knob towards [FM] or [AM]. Adjust the minutes Push the Control knob towards [4] or [].
Function of the KDC-W4534/KDC-W4034A/AY/G/ GY/KDC-W434A/G/KDC-W410A/AY/G/GY/KDCW40G/KDC-W434GY In CD mode

Supreme Setting

When MP3 or WMA files encoded at a low bit rate (less than 96kbps (fs=32k, 44.1k, 48kHz)) are played, this function restores their high frequency region to approach the sound quality of equivalents of these files encoded at a high bit rate. Processing is optimized for the compression format used (MP3, or WMA), and adjustment is made for the bit rate used. Display "SPRM ON" "SPRM OFF" Setting Plays sound using the Supreme function. Plays the original sound stored in the audio file.

Push the Control knob towards [FM] or [AM]. Select the "NAME SET" display.
4 Enter Auxiliary input display setting mode
Press the Control knob for at least 1 second. The selected Auxiliary input display is displayed.
5 Select the Auxiliary input display

Power OFF Timer

Setting the timer to turn this units power OFF automatically when Standby mode continues. Using this setting can save the vehicles battery power. Display "OFF " "OFF 20M" (Original setting) "OFF 40M" "OFF 60M" Setting Power OFF Timer function is OFF. Turns the power OFF after 20 minutes. Turns the power OFF after 40 minutes. Turns the power OFF after 60 minutes.
Demonstration mode Setting
Sets the demonstration mode.
1 Select the Demonstration mode
Push the Control knob towards [FM] or [AM]. Select the "DEMO" display.
2 Set the Demonstration mode
Press the Control knob for at least 2 seconds. Each time you press the knob at least 2 seconds, the Demonstration mode alternates between the settings shown in the table below. Display "DEMO ON" "DEMO OFF" Setting The Demonstration mode function is ON. Exit Demonstration mode (Normal mode).
Do this setting after setting <Security Code> (page 21).
Function of the KDC-W4534/KDC-W4034A/AY/G/ GY/KDC-W434A/G/KDC-W410A/AY/G/GY/KDCW40G/KDC-W434GY In Standby mode

CD Read Setting

When there is a problem with playing a CD with special format, this setting plays the CD by force. Display "CD READ1" "CD READ2" Setting Play CD and Audio file. Play CD by force.
Setting "CD READ2" cannot play Audio file. Some music CDs may not play even in the "CD READ2" mode.
Accessories/ Installation Procedure
Accessories 1..1 2..2 3..1 4
If the power is not turned ON (or it is ON, but will be OFF immediately), the speaker wire may have a short-circuit or touched the chasis of the vehicle and the protection function may have been activated. Therefore, the speaker wire should be checked. If your car is not prepared for this special connectionsystem, consult your Kenwood dealer. Only use antenna conversion adaptors (ISO-JASO) when the antenna cord has an ISO plug. Make sure that all wire connections are securely made by inserting jacks until they lock completely. If your vehicles ignition does not have an ACC position, or if the ignition wire is connected to a power source with constant voltage such as a battery wire, the power will not be linked with the ignition (i.e., it will not turn on and off along with the ignition). If you want to link the units power with the ignition, connect the ignition wire to a power source that can be turned on and off with the ignition key. If the fuse blows, first make sure that the wires have not caused a short circuit, then replace the old fuse with one with the same rating. Insulate unconnected wires with vinyl tape or other similar material. To prevent short circuits, also do not remove the caps on the ends of the unconnected wires or the terminals. Connect the speaker wires correctly to the terminals to which they correspond. The unit may receive damage or fail to work if you share the - wires and/or ground them to any metal part in the car. After the unit is installed, check whether the brake lamps, indicators, wipers, etc. on the car are working properly. If the console has a lid, make sure to install the unit so that the faceplate does not hit the lid when closing and opening. Mount the unit so that the mounting angle is 30 or less.

(KDC-W4534 only)

Installation Procedure
1. To prevent short circuits, remove the key from the ignition and disconnect the - terminal of the battery. 2. Make the proper input and output wire connections for each unit. 3. Connect the wire on the wiring harness. 4. Take Connector B on the wiring harness and connect it to the speaker connector in your vehicle. 5. Take Connector A on the wiring harness and connect it to the external power connector on your vehicle. 6. Connect the wiring harness connector to the unit. 7. Install the unit in your car. 8. Reconnect the - terminal of the battery. 9. Press the reset button.
Connecting Wires to Terminals
KDC-W4534 KDC-W4034A/W4034AY/ KDC-W434A/ W4034G/W4034GY/ W434G/W434GY/ W410A/W410AY/W410G/ W40G W410GY/3034A/3034G To Steering remote

REMO. CONT

A To Steering remote B To Kenwood disc changer/ External optional accessory C Rear left output (White)/ Rear right output (Red)
Rear left output (White)/ Rear right output (Red)

FM/AM antenna input

To connect these leads, refer to the relevant instruction manuals.
Antenna Cord (ISO) Antenna Conversion Adaptor (ISOJASO) (Accessory3) Fuse (10A) Wiring harness (Accessory1) AUX Input adaptor (Accessory4) To external audio unit (Portable Audio, etc.)

TEL mute wire (Brown)

Connect to the terminal that is grounded when either the telephone rings or during conversation. To connect the Kenwood navigation system, consult your navigation manual.
If no connections are made, do not let the wire come out from the tab. Power control/ Motor antenna control wire (Blue/White)

P.CONT ANT.CONT

Battery wire (Yellow) Ignition wire (Red)
Connect either to the power control terminal when using the optional power amplifier, or to the antenna control terminal in the vehicle.

See next page.

A7 Pin (Red) A4 Pin (Yellow)

Connector A

Connector B

Connector Function Guide

Pin Numbers for ISO Connectors External Power Connector A-4 A-5 A-7 A-8 Speaker Connector B-1 B-2 B-3 B-4 B-5 B-6 B-7 B-8 Cable Colour Functions

2WARNING Connecting the ISO Connector
The pin arrangement for the ISO connectors depends on the type of vehicle you drive. Make sure to make the proper connections to prevent damage to the unit. The default connection for the wiring harness is described in 1 below. If the ISO connector pins are set as described in 2 or 3, make the connection as illustrated. Please be sure to reconnect the cable as shown 2 below to install this unit to the Volkswagen vehicles etc.
Yellow Blue/White Red Black
Battery Power Control Ignition (ACC) Earth (Ground) Connection
Purple Purple/Black Gray Gray/Black White White/Black Green Green/Black
Rear Right (+) Rear Right () Front Right (+) Front Right () Front Left (+) Front Left () Rear Left (+) Rear Left ()
1 (Default setting) The A-7 pin (red) of the vehicles ISO connector is linked with the ignition, and the A-4 pin (yellow) is connected to the constant power supply.
Ignition cable (Red) Unit Battery cable (Yellow) A-7 Pin (Red) Vehicle A-4 Pin (Yellow)
2 The A-7 pin (red) of the vehicles ISO connector is connected to the constant power supply, and the A-4 pin (yellow) is linked to the ignition.
3 The A-4 pin (yellow) of the vehicles ISO connector is not connected to anything, while the A-7 pin (red) is connected to the constant power supply (or both the A-7 (red) and A-4 (yellow) pins are connected to the constant power supply).
When the connection is made as in 3 above, the units power will not be linked to the ignition key. For that reason, always make sure to turn off the units power when the ignition is turned off. To link the units power to the ignition, connect the ignition cable (ACC.red) to a power source that can be turned on and off with the ignition key.

Installation

Metal mounting strap (commercially available) Firewall or metal support
Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place. Self-tapping screw (commercially available) Screw (M4X8) (commercially available)

General

The power does not turn ON. The fuse has blown. After checking for short circuits in the wires, replace the fuse with one with the same rating. Theres a source you cant switch. Theres no media inserted. Set the media you want to listen to. If theres no media in this unit, you cant switch to each source. The Disc changer isnt connected. Connect the Disc changer. If the Disc changer isnt connected to its input terminal, You cant switch to an external disc source. The memory is erased when the ignition is turned OFF. The ignition and battery wire are incorrectly connected. Connect the wire correctly, referring to the section on <Connecting Wires to Terminals>. The TEL mute function does not work. The TEL mute wire is not connected properly. Connect the wire correctly, referring to the section on <Connecting Wires to Terminals>. The TEL mute function turns ON even though the TEL mute wire is not connected. The TEL mute wire is touching a metal part of the car. Pull the TEL mute wire away from the metal part of the car.

Tuner source

Radio reception is poor. The car antenna is not extended. Pull the antenna out all the way. The antenna control wire is not connected. Connect the wire correctly, referring to the section on <Connecting Wires to Terminals>.
Disc source Audio file source
"AUX EXT" is displayed without achieving External disc control mode. Unsupported disc changer is connected. Use the disc changer mentioned in the <About CD players/disc changers connected to this unit> (page 3) of the section on <Safety precautions>. The specified disc does not play, but another one plays instead. The specified CD is quite dirty. Clean the CD. The disc is loaded in a different slot from that specified. Eject the disc magazine and check the number for the specified disc. The disc is severely scratched. Try another disc instead. A CD ejects as soon as it is loaded. The CD is quite dirty. Clean the CD, referring to the CD cleaning of the section on <About CDs> (page 7). Cant remove disc. The cause is that more than 10 minutes has elapsed since the vehicle ACC switch was turned OFF. The disc can only be removed within 10 minutes of the ACC switch being turned OFF. If more than 10 minutes has elapsed, turn the ACC switch ON again and press the Eject button. The disc wont insert. Theres already another disc inserted. Press the [0] button and remove the disc. Direct Search cant be done. Another function is ON. Turn Random Play or other functions OFF. Track Search cant be done. For the discs/folders first or last song. For each disc/folder, Track Search cant be done in the backward direction for the first song or in the forward direction for the last song.

READING: IN (Blink):

The unit is reading the data on the disc. The CD player section is not operating properly. Reinsert the CD. If the CD cannot be ejected or the display continues to flash even when the CD has been properly reinserted, please switch off the power and consult your nearest service center. The speaker wire has a short-circuit or touches the chassis of the vehicle, and then the protection function is activated. Wire or insulate the speaker cable properly and press the reset button. An Audio file is played with a format that this unit cant support. ---A copy-protected file is played. ---The Demonstration mode has been selected. The <Demonstration mode Setting> (page 25) is ON. Turn it OFF.

NO DISC:

PROTECT:

TOC ERR:

NA FILE:

COPY PRO: DEMO:

E-05: BLANK: NO TRACK: E-15:

NO PANEL:

Specifications
Specifications subject to change without notice.

CD player section

Laser diode : GaAlAs Digital filter (D/A) : 8 Times Over Sampling D/A Converter : 1 Bit Spindle speed KDC-W4534/W4034A/W4034AY/W4034G/ W4034GY/W434A/W434G/W434GY/W410A/ W410AY/W410G/W410GY/W40G : rpm (CLV 2times) KDC-3034A/3034G : rpm (CLV) Wow & Flutter : Below Measurable Limit Frequency response (1 dB) : 10 Hz 20 kHz Total harmonic distortion (1 kHz) : 0.01 % Signal to Noise ratio (1 kHz) KDC-W4534/W4034A/W4034AY/W4034G/ W4034GY/W434A/W434G/W434GY/W410A/ W410AY/W410G/W410GY/W40G : 105 dB KDC-3034A/3034G : 93 dB Dynamic range : 93 dB MP3 decode KDC-W4534/W4034A/W4034AY/W4034G/ W4034GY/W434A/W434G/W434GY/W410A/ W410AY/W410G/W410GY/W40G : Compliant with MPEG-1/2 Audio Layer-3 WMA decode KDC-W4534/W4034A/W4034AY/W4034G/ W4034GY/W434A/W434G/W434GY/W410A/ W410AY/W410G/W410GY/W40G : Compliant with Windows Media Audio

FM tuner section

Frequency range (50 kHz space) : 87.5 MHz 108.0 MHz Usable sensitivity (S/N = 26dB) : 0.7 V /75 Quieting Sensitivity (S/N = 46dB) : 1.6 V /75 Frequency response (3.0 dB) : 30 Hz 15 kHz Signal to Noise ratio (MONO) : 65 dB Selectivity (DIN) (400 kHz) : 80 dB Stereo separation (1 kHz) : 35 dB

MW tuner section

Frequency range (9 kHz space) : 531 kHz 1611 kHz Usable sensitivity (S/N = 20dB) : 25 V

LW tuner section

Frequency range : 153 kHz 281 kHz Usable sensitivity (S/N = 20dB) : 45 V

Audio section

Maximum output power KDC-W4534/W4034AY/W4034GY/W434GY/ W410AY/W410GY : 50 W x 4 KDC-W4034A/W4034G/3034A/3034G/ W434A/ W434G/W410A/W410G/W40G : 45 W x 4 Output power (DIN 45324, +B=14.4V) KDC-W4534/W4034AY/W4034GY/W434GY/ W410AY/W410GY : 30 W x 4 KDC-W4034A/W4034G/3034A/3034G/ W434A/ W434G/W410A/W410G/W40G : 28 W x 4 Speaker Impedance :4-8 Tone action Bass : 100 Hz 8 dB Middle : 1 kHz 8 dB Treble : 10 kHz 8 dB Preout level / Load (during disc play) KDC-W4534/W4034A/W4034AY/W4034G/ W4034GY/W410A/W410AY/W410G/W410GY/ 3034A/3034G : 2000 mV/10 k Preout impedance (during disc play) KDC-W4534/W4034A/W4034AY/W4034G/ W4034GY/W410A/W410AY/W410G/W410GY/ 3034A/3034G : 600
Auxiliary input (Using AUX Input Adaptor)
(KDC-W4534 only) Frequency response (1 dB) : 20 Hz 20 kHz Input Maximum Voltage : 1200 mV Input Impedance : 100 k
Operating voltage (11 16V allowable) : 14.4 V Current consumption : 10 A Installation Size (W x H x D) : 182 x 53 x 155 mm Weight : 1.4 kg