Before using this unit for the first time
This unit is initially set on the Demonstration mode. When using this unit for the first time, cancel the <Demonstration mode Setting> (page 25).
About DAB Tuner control (KDC-W4534)
Reset button The characters which can be displayed by this unit are A-Z 0-9 @ " ` % & * + = ,. / \ < > [ ] ( ) : ; ^-{}|~. The RDS feature wont work where the service is not supported by any broadcasting station. The illustrations of the display and the panel appearing in this manual are examples used to explain more clearly how the controls are used. Therefore, what appears on the display in the illustrations may differ from what appears on the display on the actual equipment, and some of the illustrations on the display may be inapplicable.
Refer to A group on the Instruction manual of DAB Tuner KTC-9090DAB (optional accessory) for the control method of DAB Tuner function. However, the following control methods of the function for this unit may be differed from the Instruction manual; therefore, refer to the following supplemental instruction. <Auto Ensemble Memory Entry> 1. Select the preset band for Auto Ensemble Memory Entry. 2. Press the [AME] button for at least 2 seconds. Open Auto Ensemble Memory Entry. After storing in the memory finishes, the number of the pre-set buttons and the ensemble label are displayed. <Searching by programme type and language> and <Languages to be displayed> in <Programme Type (PTY) Function> At the operation to press [DISP] button, use [TI] button instead.

Cleaning the Unit

If the faceplate of this unit is stained, wipe it with a dry soft cloth such as a silicon cloth. If the faceplate is stained badly, wipe the stain off with a cloth moistened with neutral cleaner, then wipe it again with a clean soft dry cloth.
Applying spray cleaner directly to the unit may affect its mechanical parts. Wiping the faceplate with a hard cloth or using a volatile liquid such as thinner or alcohol may scratch the surface or erases characters.
Cleaning the Faceplate Terminals
If the terminals on the unit or faceplate get dirty, wipe them with a clean soft dry cloth.
This Product is not installed by the manufacturer of a vehicle on the production line, nor by the professional importer of a vehicle into an EU Member State.

CD storage
Do not place CDs in direct sunlight (On the seat or dashboard etc.) or where the temperature is high. Store CDs in their cases.

CD accessories

Do not use disc type accessories.

CD cleaning

Clean from the center of the disc and move outward.

General features

Release button

Control knob

ATT/DIM

LOUD indicator

ATT indicator

Clock display

Turning ON the Power Press the [SRC] button. Turning OFF the Power Press the [SRC] button for at least 1 second.
The time until full power OFF can be set in <Power OFF Timer> (page 25).

Volume

Increasing Volume Turn the [VOL] knob clockwise.

Selecting the Source

Press the [SRC] button. Source required Tuner CD External disc* (Optional accessory) Auxiliary input* Standby (Illumination only mode) Display "TUNER" "CD" "CD CH" "AUX EXT" "STANDBY"
Decreasing Volume Turn the [VOL] knob counterclockwise.

Attenuator

Turning the volume down quickly. Press the [ATT] button. Each time you press the button, the Attenuator turns ON and OFF. When the Attenuator is ON, the "ATT" indicator blinks.
* Function of the KDC-W4534 This unit automatically turns full power OFF after 20 minutes lapses in Standby mode in order to save the vehicle's battery.

System Q

Selecting the best sound setting preset for different types of music.
1 Select the source to set

Press the [SRC] button.

2 Select the Sound type
Press the [Q] button. When you press the button once, the current sound setting is displayed. Each time you press the button, the sound setting alternates. Sound setting Natural Rock Pops Easy Top 40 Jazz Display "NATURAL" "ROCK" "POPS" "EASY" "TOP40" "JAZZ"
Adjustment Item Display Range Bass level "BAS L" 8 +8 Middle level "MID L" 8 +8 Treble level "TRE L" 8 +8 Balance "BAL" Left 15 Right 15 Fader "FAD" Rear 15 Front 15 Exit Audio Control mode (Volume control mode)
5 Exit Audio Control mode
Press any button. Press a button other than the [VOL] knob, [SRC], [0] and [ATT] button.

Audio Setup

Setting the Sound system, such as Volume offset and Loudness.
1 Select the source to adjust
Change each setting value with the <Speaker Setting> (page 10). First, select the speaker type with the Speaker setting. When the value is set up by <Audio Control> (page 9), "USER" is displayed.

2 Enter Audio Setup mode

Press the [VOL] knob for at least 1 second.
3 Select the Audio Setup item to adjust
Press the [VOL] knob. Each time you press the knob, the item to be adjusted alternates between the items shown in the table below.
Audio Control 1 Select the source to adjust
4 Adjust the Audio setup item
Turn the [VOL] knob. Adjustment Item Volume offset Loudness Display "V-OFF" "LOUD" Range ON/OFF
2 Enter Audio Control mode

Press the [VOL] knob.

3 Select the Audio item to adjust
Volume offset: Sets each sources volume as a difference from the basic volume. Loudness: Compensates for low and high tones during low volume. When Loudness is ON, "LOUD" indicator is ON.

4 Adjust the Audio item

Turn the [VOL] knob.

5 Exit Audio Setup mode

Speaker Setting
Fine-tuning so that the System Q value is optimal when setting the speaker type.
In CD & External disc source
Information Disc title (In External disc source or KDCW4534/W4034A/W4034AY/W4034G/ W4034GY/W434A/W434G/W410A/W410AY/ W410G/W410GY/W40G/W434GY internal CD source) Track title (In External disc source or KDCW4534/W4034A/W4034AY/W4034G/ W4034GY/W434A/W434G/W410A/W410AY/ W410G/W410GY/W40G/W434GY internal CD source) Track number & Play time Clock Display "D-TITLE"*

1 Enter Standby

Press the [SRC] button. Select the "STANDBY" display.
2 Enter Speaker Setting mode

"T-TITLE"*

3 Select the Speaker type
Turn the [VOL] knob. Each time you turn the knob, the setting alternates between the settings shown in the table below. Speaker type OFF For 5 & 4 in. speaker For 6 & 6x9 in. speaker For the OEM speaker Display "SP OFF" "SP 5/4" "SP 6*9/6" "SP OEM"
"P-TIME" "CLOCK"

In Audio file source

Information Song title & Artist name Album name & Artist name Folder name File name Track number & Play time Clock Display "TITLE"* "ALBUM"* "FOLDER" "FILE" "P-TIME" "CLOCK"
4 Exit Speaker Setting mode
In Standby/ Auxiliary input source

Function of the KDC-W4534/KDC-W4034A/AY/G/GY/KDC-3034A/G/KDC-W410A/AY/G/GY

PTY indicator

TI indicator

Traffic Information

Changing to traffic information automatically when a traffic bulletin starts even when you are not listening to the radio. Press the [TI] button. Each time you press the button, the Traffic information function turns ON and OFF. When traffic information is ON, "TI" indicator is ON. When a traffic information station is not being received the "TI" indicator blinks. When a traffic bulletin starts, "TRAFFIC" is displayed and the audio changes to traffic information.
During reception of an AM station when the Traffic Information function is turned ON, the frequency changes to an FM station. During reception of traffic information the adjusted volume is automatically remembered, and the next time the audio changes to traffic information, the volume automatically becomes the remembered volume.
Receiving other traffic information stations Push the Control knob towards [4] or [].
Traffic information can be switched when it is on the Tuner Source. However, you cannot switch the Traffic information during reception of the Traffic bulletin switched from the source other than the Tuner.
Function of the KDC-W4534

Radio Text Scroll

Scrolling the displayed radio text. Hold down on [FM] of the Control knob for at least 2 seconds.

PTY (Program Type)

Selecting the Program Type and searching for a station.
Speech and Music include the Program type shown below. Music: No.12 17, Speech: No.3 11, 18 25, 31 You can put the Program Type in the [1] [6] button memory and for quick recall. Refer to the <Program Type preset> (page 15). You can change the display language. Refer to <Changing Language for PTY Function> (page 16).

1 Enter PTY mode

Press the Control knob. During PTY mode the "PTY" indicator is ON.
This function cannot be used during a traffic bulletin or AM reception.
2 Select the Program Type
Push the Control knob towards [FM] or [AM]. Each time you push the knob, the Program Type alternates between the program types shown in the table below. No. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 28. 29. 30. 31. Program Type Speech Music News Current Affairs Information Sport Education Drama Culture Science Varied Pop Music Rock Music Easy Listening Music Light Classical Serious Classical Other Music Weather Finance Childrens programs Social Affairs Religion Phone In Travel Leisure Jazz Music Country Music National Music Oldies Music Folk Music Documentary Display "SPEECH" "MUSIC" "NEWS" "AFFAIRS" "INFO" "SPORT" "EDUCATE" "DRAMA" "CULTURE" "SCIENCE" "VARIED" "POP M" "ROCK M" "EASY M" "LIGHT M" "CLASSICS" "OTHER M" "WEATHER" "FINANCE" "CHILDREN" "SOCIAL" "RELIGION" "PHONE IN" "TRAVEL" "LEISURE" "JAZZ" "COUNTRY" "NATION M" "OLDIES" "FOLK M" "DOCUMENT"

3 Search for the selected Program Type
station Push the Control knob towards [4] or []. When you want to search for other stations, push [4] or [] of the Control knob again.
When the selected Program Type is not found, "NO PTY" is displayed. Select another Program Type.

4 Exit PTY mode

Program Type preset
Putting the Program Type in the Preset button memory and quick recall.
Presetting the Program Type
1 Select the Program Type to preset
Refer to <PTY (Program Type)> (page 15).
2 Preset the Program Type
Press the desired [1] [6] button for at least 2 seconds.
Recalling the preset Program Type
2 Recall the Program Type
Press the desired [1] [6] button.
Changing Language for PTY Function
Selecting the Program Type display language.
2 Enter Changing Language mode

Press the [TI] button.

3 Select the language
Push the Control knob towards [FM] or [AM]. Each time you push the knob, the language alternates between the languages shown in the table below. Language English French German Display "ENGLISH" "FRENCH" "GERMAN"
4 Exit Changing Language mode
CD/Audio file/External disc control features

RDM/ 3

F.SEL M.RDM

Disc number

IN indicator

Track number

Play time
Playing CD & Audio file
When a disc is inserted Press the [SRC] button. Select the "CD" display.
When a CD is inserted, the "IN" indicator is ON.

Playing External Disc

Playing discs set in the optional accessory disc player connected to this unit. Press the [SRC] button. Select the display for the disc player you want. Display examples: Display "CD CH" "MD CH" Disc player CD changer MD changer
Pause and play Press the Control knob. Each time you press the knob, the audio pauses or plays. Eject the CD Press the [0] button.
Refer to <About MP3 and WMA> (page 6) for the Audio file by models you can play.
Pause and play Press the Control knob. Each time you press the knob, the audio pauses or plays.
Disc 10 is displayed as "0". The functions that can be used and the information that can be displayed will differ depending on the external disc players being connected.

1 Enter Menu mode

Press the [MENU] button for at least 1 second. "MENU" is displayed.

2 Select the menu item

Push the Control knob towards [FM] or [AM]. Example: When you want to set the beep sound, select the "BEEP" display.

3 Set the menu item

Push the Control knob towards [4] or []. Example: When you select "BEEP", each time you push the knob it alternates between "BEEP ON" or "BEEP OFF". Select 1 of them as the setting.
Function of the KDC-W4534 In Standby mode

Security Code

Activating the Security Code disables the usage of audio unit by someone else. Once the Security Code is activated, the entry of authorized Security Code is required to turn on the audio unit when it is removed from the vehicle. Indication of this Security Code activation prevents your precious audio unit from stealing.
If you enter a Code different from your Security Code, you have to start over from step 4.
Resetting the Security Code function when the audio unit is first used after removed from the battery power source or the Reset button is pressed
1 Turn the power ON. 2 Do the step 4 through 7 step operation, and
reenter the security code. "APPROVED" is displayed. Now, you can use the unit.
If an incorrect code is entered, "WAITING" is displayed, and the input prohibition periods shown in the table below is generated. After the input prohibition time lapses, "CODE" is displayed, and you can reenter the code.
Set the Security Code when the <Demonstration mode Setting> (page 25) is set to OFF. When you activate the Security Code function, it cannot be released. Note, your Security Code is the 4 digit number entered in your "Car Audio Passport" in this package.

2 Enter Menu mode

Press the [MENU] button for at least 1 second. When "MENU" is displayed, "CODE SET" is displayed.
3 Enter Security Code mode
Press the Control knob for at least 2 seconds. When "ENTER" is displayed, "CODE" is also displayed.
Number of times the incorrect code was input 3 4
Input prohibited time 5 minutes 1 hour 24 hours

In Standby mode

4 Select the digits to enter

Touch Sensor Tone

Setting the operation check sound (beep sound) ON/OFF. Display "BEEP ON" "BEEP OFF" Setting Beep is heard. Beep canceled.
5 Select the Security Code numbers
6 Repeat steps 4 and 5, and complete the

Security Code.

7 Confirm the Security Code
Press the Control knob for at least 3 seconds. When "RE-ENTER" is displayed, "CODE" is also displayed.
8 Do the step 4 through 7 step operation, and
reenter the security code. "APPROVED" is displayed. The Security Code function activates.
In Standby mode Function of the KDC-W4534

Manual Clock Adjustment

You can do this adjustment when the <Synchronize Clock> (page 22) is set as OFF.

Selectable Illumination

Selecting the button illumination color as green or red. Display "KEY RED" "KEY GRN" Setting The illumination color is red. The illumination color is green.
1 Select Clock Adjustment mode
Push the Control knob towards [FM] or [AM]. Select the "CLK ADJ" display.
2 Enter Clock Adjust mode
Press the Control knob for at least 1 second. The clock display blinks.

3 Adjust the hours

Push the Control knob towards [FM] or [AM]. Adjust the minutes Push the Control knob towards [4] or [].
Function of the KDC-W4534/KDC-W4034A/AY/G/ GY/KDC-W434A/G/KDC-W410A/AY/G/GY/KDCW40G/KDC-W434GY In CD mode

Supreme Setting

When MP3 or WMA files encoded at a low bit rate (less than 96kbps (fs=32k, 44.1k, 48kHz)) are played, this function restores their high frequency region to approach the sound quality of equivalents of these files encoded at a high bit rate. Processing is optimized for the compression format used (MP3, or WMA), and adjustment is made for the bit rate used. Display "SPRM ON" "SPRM OFF" Setting Plays sound using the Supreme function. Plays the original sound stored in the audio file.
4 Exit Clock adjustment mode
Function of the KDC-W4534/KDC-W4034A/AY/G/ GY/KDC-3034A/G/KDC-W410A/AY/G/GY In Standby mode

Synchronize Clock

Synchronizing the RDS station time data and this units clock. Display "SYNC ON" "SYNC OFF" Setting Synchronizes the time. Adjust the time manually.

The sound effect may be imperceptible depending on the relationship between the audio file format and setting.
It takes 3 to 4 minutes to synchronize the clock.
Function of the KDC-W4534/KDC-W4034A/AY/G/ GY/KDC-3034A/G/KDC-W410A/AY/G/GY
DSI (Disabled System Indicator)
A red indicator will blink on the unit after the faceplate is removed, warning potential thieves. Display "DSI ON" "DSI OFF" Setting LED flashes. LED OFF.
News Bulletin with Timeout Setting
The tuner automatically changes when a news bulletin starts even if the radio is not being listened to. Also, you can set the time interval when interruption is prohibited. Display and Setting "NEWS OFF" "NEWS 00M" "NEWS 90M" When you set "NEWS 00M" "NEWS 90M", the News Bulletin Interrupt function is ON. When the news bulletin starts, "NEWS" is displayed, and the tuner changes to the news bulletin.
If you choose the "20MIN" setting, further news bulletins will not be received for 20 minutes once the first news bulletin is received. The news bulletin volume is the same level that was set for <Traffic Information> (page 14). This news bulletin function is only available if the desired station sends PTY-code for news bulletin or belongs to <Enhanced Other Network>-Network sending PTY-code for news bulletin. When the News Bulletin Interrupt function is ON, the tuner changes to an FM station.
Function of the KDC-W4534/KDC-W4034A/AY/G/ GY/KDC-3034A/G/KDC-W410A/AY/G/GY In Tuner mode
Sets the tuning mode. Tuning mode Auto seek Preset station seek Manual Display "AUTO 1" "AUTO 2" "MANUAL" Operation Automatic search for a station. Search in order of the stations in the Preset memory. Normal manual tuning control.
AF (Alternative Frequency)
When the reception is poor, automatically alternate to another frequency broadcasting the same program in the same RDS network with better reception. Display "AF ON" "AF OFF" Setting The AF function is ON. The AF function is OFF.
When the AF function is ON, the "RDS" indicator is ON.
When no other stations with stronger reception are available for the same program in the RDS network, you may hear the incoming broadcast in bits and snatches. Turn OFF the AF function in such a case.

In Tuner mode

Local Seek
Only stations whose reception is good are searched in auto seek tuning. Display "LO.S OFF" "LO.S ON" Setting The local seek function is OFF. The local seek function is ON.

Restricting RDS Region (Region Restrict Function)
You can choose whether or not to restrict the RDS channels, received with the AF function for a particular network, to a specific region. Display "REG ON" "REG OFF" Setting The Region Restrict Function is ON. The Region Restrict Function is OFF.
If AF function is not restricted to the specified region and network, the AF function sets up to search the station with good reception in the same RDS network.
Each time you push the knob, the display alternates as listed below. "AUX EXT" "DVD" "PORTABLE" "GAME" "VIDEO" "TV"

Auto TP Seek

When the TI function is ON and the reception is poor while listening to a traffic information station, another traffic information station with better reception will be searched for automatically. Display "ATPS ON" "ATPS OFF" Setting The Auto TP Seek Function is ON. The Auto TP Seek Function is OFF.
6 Exit Auxiliary input display setting mode
When operation stops for 10 seconds, the name at that time is registered, and the Auxiliary input display setting mode closes.

In FM reception

Monaural Reception
You can reduce the noise when stereo broadcasts are received as monaural. Display "MONO OFF" "MONO ON" Setting The monaural reception is OFF. The monaural reception is ON.

Text Scroll

Setting the displayed text scroll. Display "SCL MANU" "SCL AUTO" Setting Doesnt scroll. Scrolls when the display changes.
Auxiliary Input Display Setting
Selecting the display when alternating to Auxiliary input source.
The text scrolled is listed below. - CD text - Folder name/ File name/ Song title/ Artist name/ Album name - MD title - Radio text
1 Select Auxiliary input source
Press the [SRC] button. Select the "AUX EXT" display.
3 Select Auxiliary input display setting mode
Push the Control knob towards [FM] or [AM]. Select the "NAME SET" display.

4 Enter Auxiliary input display setting mode
Press the Control knob for at least 1 second. The selected Auxiliary input display is displayed.
5 Select the Auxiliary input display

Power OFF Timer

Setting the timer to turn this units power OFF automatically when Standby mode continues. Using this setting can save the vehicles battery power. Display "OFF " "OFF 20M" (Original setting) "OFF 40M" "OFF 60M" Setting Power OFF Timer function is OFF. Turns the power OFF after 20 minutes. Turns the power OFF after 40 minutes. Turns the power OFF after 60 minutes.
Demonstration mode Setting
Sets the demonstration mode.
1 Select the Demonstration mode
Push the Control knob towards [FM] or [AM]. Select the "DEMO" display.
2 Set the Demonstration mode
Press the Control knob for at least 2 seconds. Each time you press the knob at least 2 seconds, the Demonstration mode alternates between the settings shown in the table below. Display "DEMO ON" "DEMO OFF" Setting The Demonstration mode function is ON. Exit Demonstration mode (Normal mode).
Do this setting after setting <Security Code> (page 21).
Function of the KDC-W4534/KDC-W4034A/AY/G/ GY/KDC-W434A/G/KDC-W410A/AY/G/GY/KDCW40G/KDC-W434GY In Standby mode

CD Read Setting

When there is a problem with playing a CD with special format, this setting plays the CD by force. Display "CD READ1" "CD READ2" Setting Play CD and Audio file. Play CD by force.
Setting "CD READ2" cannot play Audio file. Some music CDs may not play even in the "CD READ2" mode.
Accessories/ Installation Procedure
Accessories 1..1 2..2 3..1 4
If the power is not turned ON (or it is ON, but will be OFF immediately), the speaker wire may have a short-circuit or touched the chasis of the vehicle and the protection function may have been activated. Therefore, the speaker wire should be checked. If your car is not prepared for this special connectionsystem, consult your Kenwood dealer. Only use antenna conversion adaptors (ISO-JASO) when the antenna cord has an ISO plug. Make sure that all wire connections are securely made by inserting jacks until they lock completely. If your vehicles ignition does not have an ACC position, or if the ignition wire is connected to a power source with constant voltage such as a battery wire, the power will not be linked with the ignition (i.e., it will not turn on and off along with the ignition). If you want to link the units power with the ignition, connect the ignition wire to a power source that can be turned on and off with the ignition key. If the fuse blows, first make sure that the wires have not caused a short circuit, then replace the old fuse with one with the same rating. Insulate unconnected wires with vinyl tape or other similar material. To prevent short circuits, also do not remove the caps on the ends of the unconnected wires or the terminals. Connect the speaker wires correctly to the terminals to which they correspond. The unit may receive damage or fail to work if you share the - wires and/or ground them to any metal part in the car. After the unit is installed, check whether the brake lamps, indicators, wipers, etc. on the car are working properly. If the console has a lid, make sure to install the unit so that the faceplate does not hit the lid when closing and opening. Mount the unit so that the mounting angle is 30 or less.

Yellow Blue/White Red Black
Battery Power Control Ignition (ACC) Earth (Ground) Connection
Purple Purple/Black Gray Gray/Black White White/Black Green Green/Black
Rear Right (+) Rear Right () Front Right (+) Front Right () Front Left (+) Front Left () Rear Left (+) Rear Left ()
1 (Default setting) The A-7 pin (red) of the vehicles ISO connector is linked with the ignition, and the A-4 pin (yellow) is connected to the constant power supply.
Ignition cable (Red) Unit Battery cable (Yellow) A-7 Pin (Red) Vehicle A-4 Pin (Yellow)
2 The A-7 pin (red) of the vehicles ISO connector is connected to the constant power supply, and the A-4 pin (yellow) is linked to the ignition.
3 The A-4 pin (yellow) of the vehicles ISO connector is not connected to anything, while the A-7 pin (red) is connected to the constant power supply (or both the A-7 (red) and A-4 (yellow) pins are connected to the constant power supply).
When the connection is made as in 3 above, the units power will not be linked to the ignition key. For that reason, always make sure to turn off the units power when the ignition is turned off. To link the units power to the ignition, connect the ignition cable (ACC.red) to a power source that can be turned on and off with the ignition key.

Installation

Metal mounting strap (commercially available) Firewall or metal support
Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place. Self-tapping screw (commercially available) Screw (M4X8) (commercially available)
Make sure that the unit is installed securely in place. If the unit is unstable, it may malfunction (for example, the sound may skip).

Removing the Unit

Removing the hard rubber frame 1 Engage the catch pins on the removal tool and
remove the two locks on the upper level. Upper the frame and pull it forward as shown in the figure.
Removing the Unit 1 Refer to the section <Removing the hard rubber 2 3
frame> (page 30) and then remove the hard rubber frame. Remove the screw (M4 8) on the back panel. Insert the two removal tools deeply into the slots on each side, as shown.

Screw (M4X8) (commercially available)

Lock Catch

Accessory2 Removal tool
2 When the upper level is removed, remove the

lower two locations.

4 Lower the removal tool toward the bottom, and
pull out the unit halfway while pressing towards the inside.
The frame can be removed from the bottom side in the same manner.
Be careful to avoid injury from the catch pins on the removal tool.
5 Pull the unit all the way out with your hands,
being careful not to drop it.

Troubleshooting Guide

What might seem to be a malfunction in your unit may just be the result of slight misoperation or miswiring. Before calling service, first check the following table for possible problems.
Even if Loudness is turned ON, high-pitched tone isnt compensated for. Tuner source is selected. High-pitched tone isnt compensated for when in Tuner source. No sound can be heard, or the volume is low. The fader or balance settings are set all the way to one side. Center the fader and balance settings. The input/output wires or wiring harness are connected incorrectly. Reconnect the input/output wires or the wiring harness correctly. See the section on <Connecting Wires to Terminals>. The values of Volume offset are low. Turn up the Volume offset, referring to the section on <Audio Setup> (page 9). The sound quality is poor or distorted. One of the speaker wires is being pinched by a screw in the car. Check the speaker wiring. The speakers are not wired correctly. Reconnect the speaker wires so that each output terminal is connected to a different speaker. The Touch Sensor Tone doesnt sound. The preout jack is being used. The Touch Sensor Tone cant be output from the preout jack. Even though Synchronize Clock is ON, the clock cant be adjusted. The received RDS station isnt sending time data. Receive another RDS station.

General

The power does not turn ON. The fuse has blown. After checking for short circuits in the wires, replace the fuse with one with the same rating. Theres a source you cant switch. Theres no media inserted. Set the media you want to listen to. If theres no media in this unit, you cant switch to each source. The Disc changer isnt connected. Connect the Disc changer. If the Disc changer isnt connected to its input terminal, You cant switch to an external disc source. The memory is erased when the ignition is turned OFF. The ignition and battery wire are incorrectly connected. Connect the wire correctly, referring to the section on <Connecting Wires to Terminals>. The TEL mute function does not work. The TEL mute wire is not connected properly. Connect the wire correctly, referring to the section on <Connecting Wires to Terminals>. The TEL mute function turns ON even though the TEL mute wire is not connected. The TEL mute wire is touching a metal part of the car. Pull the TEL mute wire away from the metal part of the car.

The messages shown below display your systems condition.
EJECT: No disc magazine has been loaded in the changer. The disc magazine is not completely loaded. Load the disc magazine properly. No CD in the unit. Insert the CD. No disc has been loaded in the disc magazine. Load a disc into the disc magazine. No disc has been loaded in the disc magazine. Load a disc into the disc magazine. The CD is quite dirty. The CD is upsidedown. The CD is scratched a lot. Clean the CD and load it correctly. The CD is upside-down. Load the CD correctly. Nothing has been recorded on the MD. No tracks are recorded on the MD, although it has a title. Media was played that doesnt have data recorded that the unit can play. Use media that has data recorded that the unit can play. The faceplate of the slave unit being connected to this unit has been removed. Replace it. The unit is malfunctioning for some reason. Press the reset button on the unit. If the "E-77" code does not disappear, consult your nearest service center. Something is wrong with the disc magazine. Or the unit is malfunctioning for some reason. Check the disc magazine. And then press the reset button on the unit. If the "E-99" code does not disappear, consult your nearest service center. The protective circuit in the unit activates when the temperature inside the automatic disc changer exceeds 60C (140F), stopping all operation. Cool down the unit by opening the windows or turning on the air conditioner. As the temperature falls below 60C (140F), the disc will start playing again. Discs are being exchanged in the Disc changer.

READING: IN (Blink):

The unit is reading the data on the disc. The CD player section is not operating properly. Reinsert the CD. If the CD cannot be ejected or the display continues to flash even when the CD has been properly reinserted, please switch off the power and consult your nearest service center. The speaker wire has a short-circuit or touches the chassis of the vehicle, and then the protection function is activated. Wire or insulate the speaker cable properly and press the reset button. An Audio file is played with a format that this unit cant support. ---A copy-protected file is played. ---The Demonstration mode has been selected. The <Demonstration mode Setting> (page 25) is ON. Turn it OFF.

NO DISC:

PROTECT:

TOC ERR:

NA FILE:

COPY PRO: DEMO:

E-05: BLANK: NO TRACK: E-15:

NO PANEL:

Specifications
Specifications subject to change without notice.