KVT-815DVD KVT-745DVD KVT-715DVD
MONITOR WITH DVD RECEIVER

INSTALLATION MANUAL

MONITEUR AVEC RCEPTEUR DVD

MANUEL D'INSTALLATION

MONITOR CON RECEPTOR DVD

MANUAL DE INSTALACIN

MONITOR COM RECEPTOR DVD

MANUAL DE INSTALAO

PRINTED IN JAPAN B54-4433-00/00 (K)(AI)

Before Installation

Accessories

English 1

2 English

Installation Procedure

1. To prevent a short circuit, remove the key from the ignition and disconnect the - battery. 2. Make the proper input and output wire connections for each unit. 3. Connect the speaker wires of the wiring harness. 4. Connect the wiring harness wires in the following order: ground, battery, ignition. 5. Connect the wiring harness connector to the unit. 6. Install the unit in your car. 7. Reconnect the - battery. 8. Press the reset button.

2WARNING

If you connect the ignition wire (red) and the battery wire (yellow) to the car chassis (ground), you may cause a short circuit, that in turn may start a fire. Always connect those wires to the power source running through the fuse box.

2CAUTION

If your car's ignition does not have an ACC position, connect the ignition wires to a power source that can be turned on and off with the ignition key. If you connect the ignition wire to a power source with a constant voltage supply, as with battery wires, the battery may die. If the console has a lid, make sure to install the unit so that the faceplate will not hit the lid when closing and opening. If the fuse blows, first make sure the wires arent touching to cause a short circuit, then replace the old fuse with one with the same rating. Insulate unconnected wires with vinyl tape or other similar material. To prevent a short circuit, do not remove the caps on the ends of the unconnected wires or the terminals. Connect the speaker wires correctly to the terminals to which they correspond. The unit may be damaged or fail to work if you share the - wires or ground them to any metal part in the car. When only two speakers are being connected to the system, connect the connectors either to both the front output terminals or to both the rear output terminals (do not mix front and rear). For example, if you connect the + connector of the left speaker to a front output terminal, do not connect the - connector to a rear output terminal. After the unit is installed, check whether the brake lamps, blinkers, wipers, etc. on the car are working properly. Mount the unit so that the mounting angle is 30 or less.

English 3

Connection

Battery

4 English

English

Monitor unit

Do not connect.

Connect to the vehicle's parking brake detection switch harness using the supplied relay connector. 2 CAUTION For the sake of safety, be sure to connect the parking sensor.

PRK SW

Wiring harness (Accessory 3)
Ground wire (Black) - (To car chassis) Battery wire (Yellow)

( 5A )

Ignition wire (Red) Accessory 4 FM/AM antenna input

Accessory 2

To car light control switch Ignition key switch ACC
Battery wire (Yellow) Dimmer control wire (Orange/White)

Car fuse box (Main fuse)

Ground wire (Black) - (To car chassis)

Car fuse box

Depending on what antenna you are using, Motor antenna control wire connect either to the control terminal of the motor (Blue) antenna, or to the power terminal for the booster amplifier of the film-type antenna. Power control wire When using the optional power amplifier, (Blue/White) connect to its power control terminal. External amplifier control wire To "EXT.AMP.CONT." terminal of the amplifier (Pink/Black) having the external amp control function.
Receiver unit (front side)
PREOUT TO TV TUNER I/F TO NAVIGATION I/F TO 5L-I/F

Disc Changer etc.

Cable (included in the disc changer)
Receiver unit (rear side)
POWER TO MONITOR I/F AV INPUT FM /AM AV OUTPUT ANTENNA
Wiring harness (Accessory 1)

Mute wire (Brown)

Connect to the terminal that is grounded when either the telephone rings or during conversation.

( 10A )

White/Black

ILLUMI

To connect the KENWOOD navigation system, consult your navigation manual.

White Gray/Black Gray

ANT. CONT

To front left speaker

To front right speaker

Green/Black Green

To rear left speaker

P CONT

Purple/Black Purple

EXT.CONT

To rear right speaker

English 5

System Connection

PREOUT

TO TV TUNER I/F

TO NAVIGATION I/F

TO 5L-I/F

Front Preout

Audio left output (White) Audio right output (Red)

Rear Preout

SUB WOOFER

Sub-woofer (Mono) Preout

AV INPUT FM /AM AV OUTPUT ANTENNA

AV OUT

6 English

TO MONITOR I/F

Audio/Visual Output
Visual output (Yellow) Audio left output (White) Audio right output (Red)

Audio/Visual input

Visual input (Yellow) Audio left input (White) Audio right input (Red)

Installation

Installation for Monitor/Player Unit
Firewall or metal support
Screw (M4X8) (commercially available)
Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place. Self-tapping screw (commercially available)
Metal mounting strap (commercially available)

Accessory 5

Make sure that the unit is installed securely in place. If the unit is unstable, it may malfunction (eg, the sound may skip).
Installation for Receiver unit
1. Attach the installation brackets 9 to the sides of the hideaway unit using the sems bolts 7.
Installation brackets (Accessory 9) Sems bolts (Mmm) (Accessory 7)
2. Use the tapping screw 8 to secure the hideaway unit to the audio board.
Tapping screw (mm) (Accessory 8)

English 7

Installing in Japanese-Made Cars
Installing on Toyota, Nissan or Mitsubishi Car Using Brackets at Holes shown by ""

Accessory - or = Bracket

Accessory - or =
Screws (included in audio unit package)

Audio unit or others

8 English
Installation on Toyota Car using Brackets at Holes shown by ""
When using the bracket shown above, you cannot use screws at two holes of the right and left unit sides. If so, tighten the bracket using accessories 0 as shown below. 1. Use accessories 0 at both sides as shown.
Accessory 0 Accessory 0 Audio unit or others
2. Mount the bracket at each side.

Accessory Bracket

Accessory -
Screws (included in audio unit package) Screws (included in audio unit package)
3. Bend each end of accessory 0 to fix the bracket.
Use a flat-blade screwdriver or pliers, and bend each accessory tab into the hole of installation bracket to fix the bracket.

English 9

Removing Monitor/Player Unit
Removing the Hard Rubber Frame (escutcheon)
1. Engage the catch pins on the removal tool 6 and remove the two locks on the lower level. Lower the frame and pull it forward as shown in the figure.

Accessory 6

2. When the lower level is removed, remove the upper two locations.