KVT-827DVD KVT-727DVD KVT-627DVD
MONITOR WITH DVD RECEIVER

INSTALLATION MANUAL

MONITEUR AVEC REPTEUR DVD

MANUEL D'INSTALLATION

MONITOR MIT DVD RECEIVER

INSTALLATION-HANDBUCH

MONITOR MET DVD-ONTVANGER

INSTALLATIE HANDLEIDING

MONITOR CON RICEVITORE DVD

MANUALE DI INSTALLAZIONE

MONITOR CON RECEPTOR DVD

MANUAL DE INSTALACION

MONITOR COM RECEPTOR DVD

MANUAL DE INSTALAAO

B54-4465-00/00 (EV/E2V)

Accessories

1..1 2..1 3*..1 4..1 5..1 6

* KVT-827DVD/727DVD only

0..2 !..1 @..1 #*..1 $*..2

..1 7..2 8..4 9..4

English

Installation Procedure

1. To prevent a short circuit, remove the key from the ignition and disconnect the - battery. 2. Make the proper input and output wire connections for each unit. 3. Connect the speaker wires of the wiring harness. 4. Take Connector B on the wiring harness and connect it to the speaker connector in your vehicle. 5. Take Connector A on the wiring harness and connect it to the external power connector on your vehicle. 6. Connect the wiring harness connector to the unit. 7. Install the unit in your car. 8. Reconnect the - battery. 9. Press the reset button.

2WARNING

If you connect the ignition wire (red) and the battery wire (yellow) to the car chassis (ground), you may cause a short circuit, that in turn may start a fire. Always connect those wires to the power source running through the fuse box. Do not cut out the fuse from the ignition wire (red) and the battery wire (yellow). The power supply must be connected to the wires via the fuse.

2CAUTION

If the power is not turned ON (or it is ON, but will be OFF immediately), the speaker wire may have a short-circuit or touched the chasis of the vehicle and the protection function may have been activated. Therefore, the speaker wire should be checked. If your cars ignition does not have an ACC position, connect the ignition wires to a power source that can be turned on and off with the ignition key. If you connect the ignition wire to a power source with a constant voltage supply, as with battery wires, the battery may die. If the console has a lid, make sure to install the unit so that the faceplate will not hit the lid when closing and opening. If the fuse blows, first make sure the wires arent touching to cause a short circuit, then replace the old fuse with one with the same rating. Insulate unconnected wires with vinyl tape or other similar material. To prevent a short circuit, do not remove the caps on the ends of the unconnected wires or the terminals. Connect the speaker wires correctly to the terminals to which they correspond. The unit may be damaged or fail to work if you share the - wires or ground them to any metal part in the car. When only two speakers are being connected to the system, connect the connectors either to both the front output terminals or to both the rear output terminals (do not mix front and rear). For example, if you connect the + connector of the left speaker to a front output terminal, do not connect the connector to a rear output terminal. After the unit is installed, check whether the brake lamps, blinkers, wipers, etc. on the car are working properly. Mount the unit so that the mounting angle is 30 or less.

English |

Connection
When handling an optical cable for wiring, use care not to exceed the minimum cable bend radius of 30 mm. If you exceed the minimum bend limit, optical fibers within the optical cable may be damaged.
Optical output (KVT-827DVD/727DVD only)

Monitor unit

An Optical cable (Accessory 3) is fixed with a chassis using harness band (Accessory $). (KVT-827DVD/727DVD only) For the sake of safety, be sure to connect the parking sensor. Connect to the vehicle's parking brake detection switch harness using the supplied relay connector. (Black) Accessory 4 Parking sensor wire (Green)

PRK SW

To vehicle's reverse lamp harness
Reverse sensor wire (Pink)

REVERSE

To Steering remote
Steering remote control input (Light Blue/Yellow)

REMO.CONT

Dimmer control wire (Orang/White)

ILLUMI

Ignition wire (Red)

Battery wire (Yellow)

Ground wire (Black) - (To car chassis)
Receiver unit (front side)
PRE OUTPUT R-CAM V-IN VIDEO CENTER SUB [MONO] REAR L R FRONT L POWER R

Battery

AV OUTPUT VIDEO AV INPUT 2 L AV INPUT 1 L R R L R

Antenna Cord Accessory !

FM/AM antenna input Accessory 5

FM /AM ANTENNA VIDEO

To Subwoofer system Accessory 1 Accessory # (KVT-827DVD/727DVD only) If no connections are made, do not let the cable come out from the tab.
Connect to the terminal that is grounded when either the telephone rings or during conversation. To connect the Kenwood navigation system, consult your navigation manual. Connect either to the power control terminal when using the optional power amplifier, or to the antenna control terminal in the vehicle. To "EXT.AMP.CONT." terminal of the amplifier having the external amp control function.

Mute wire (Brown)

Power control/ Motor antenna control cable (Blue/White)

P. CONT ANT CONT

External amplifier control wire (Pink/Black)

EXT.CONT

Accessory 3 (KVT-827DVD/727DVD only) An Optical cable (Accessory 3) is fixed with a chassis using harness band (Accessory $). (KVT-827DVD/727DVD only)

Disc Changer etc. (Optional)

(Green)

Connection cable (Included in the disc changer)
Receiver unit (rear side)

Accessory 2

TV tuner (Optional)

TV ANTENNA INPUT

D A C B
Dimmer control wire (Orang/White) Ignition wire (Red) Ground wire (Black) (To car chassis)

Connector A

Connector B

TO NAVIGATION I/F

TO TV TUNER I/F

OPTICAL IN

TO MONITOR UNIT

TO MONITOR I/F

TO 5L I/F
Optical input (KVT-827DVD/727DVD only) Connection cable (Included in the Navigation system)
Connection cable (Included in the TV tuner)
Navigation System (Optional)
If you connect the ignition wire (red) and the battery wire (yellow) to the car chassis (ground), you may cause a short circuit, that in turn may start a fire. Always connect those wires to the power source running through the fuse box.
Connecting the ISO Connector
The pin arrangement for the ISO connectors depends on the type of vehicle you drive. Make sure to make the proper connections to prevent damage to the unit. The default connection for the wiring harness is described in 1 below. If the ISO connector pins are set as described in 2 or 3, make the connection as illustrated. Please be sure to reconnect the cable as shown 2 below to install this unit to the Volkswagen vehicles etc.
1 (Default setting) The A-7 pin (red) of the vehicle's ISO connector is linked with the ignition, and the A-4 pin (yellow) is connected to the constant power supply.
Unit Ignition wire (Red) Battery wire (Yellow) Vehicle A7 Pin (Red) A4 Pin (Yellow)
2 The A-7 pin (red) of the vehicle's ISO connector is connected to the constant power supply, and the A-4 pin (yellow) is linked to the ignition.
3 The A-4 pin (yellow) of the vehicle's ISO connector is not connected to anything, while the A-7 pin (red) is connected to the constant power supply (or both the A-7 (red) and A-4 (yellow) pins are connected to the constant power supply).
Unit Ignition wire (Red) Battery wire (Yellow) Vehicle A7 Pin (Red) Connect to a power source that can be turned on and off with the ignition key.

Connector Function Guide

Pin Numbers for ISO Connectors External Power Connector A4 A5 A6 A7 A8 Speaker Connector B1 B2 B3 B4 B5 B6 B7 B8 Cable Colour Yellow Blue/White Orange/White Red Black Purple Purple/Black Gray Gray/Black White White/Black Green Green/Black Functions Battery Power Control Dimmer Ignition (ACC) Earth (Ground) Connection Rear Right (+) Rear Right () Front Right (+) Front Right () Front Left (+) Front Left () Rear Left (+) Rear Left ()
Connection for AV Equipments

(KVT-827DVD/727DVD)

AV OUTPUT VIDEO FM /AM ANTENNA VIDEO AV INPUT 2 L AV INPUT 1 L R R L R-CAM V-IN VIDEO CENTER SUB [MONO]
PRE OUTPUT REAR L R FRONT L POWER R
Front Preout Audio left output (White) Audio right output (Red) Rear Preout Audio left output (White) Audio right output (Red) Subwoofer (MONO) Preout You can use Accessory # when to connect the subwoofer system input terminals is stereo. Center Preout

Rear View Camera Input Visual input (Yellow)
Audio/Visual Output Visual output (Yellow) Audio left output (White) Audio right output (Red)
Audio/Visual input 1 Visual input (Yellow) Audio left input (White) Audio right input (Red)
Audio/Visual input 2 Visual input (Yellow) Audio left input (White) Audio right input (Red) English |

(KVT-627DVD)

AV OUTPUT L FM /AM ANTENNA VIDEO AV INPUT L R-CAM V-IN VIDEO

SUB L R

Front Preout Audio left output (White) Audio right output (Red) Rear Preout Audio left output (White) Audio right output (Red) Subwoofer Preout Audio left output (White) Audio right output (Red) Rear View Camera Input Visual input (Yellow)
Audio/Visual input Visual input (Yellow) Audio left input (White) Audio right input (Red)
Installation for Monitor Unit
Firewall or metal support
Screw (M4X8) (commercially available)
Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place. Self-tapping screw (commercially available) Metal mounting strap (commercially available) Accessory 6
Make sure that the unit is installed securely in place. If the unit is unstable, it may malfunction (eg, the sound may skip).
Installation for Receiver unit
1. Attach the installation brackets 0 to the sides of the hideaway unit using the sems bolts 8.
Installation brackets (Accessory 0)
Sems bolts (Mmm) (Accessory 8)
2. Use the tapping screw 9 to secure the hideaway unit to the audio board.
Tapping screw (mm) (Accessory 9)

Removing Monitor Unit

Removing the Hard Rubber Frame (escutcheon)
1. Engage the catch pins on the removal tool 7 and remove the two locks on the lower level. Lower the frame and pull it forward as shown in the figure.
Removal Tool (Accessory 7) Catch Lock
2. When the lower level is removed, remove the upper two locations.

Removing the Unit

1. Remove the hard rubber frame by referring to the removal procedure in the section <Removing the Hard Rubber Frame>. 2. Remove the Hex-head screw with integral washer (M4 8) on the back panel. 3. Insert the two removal tools 7 deeply into the slots on each side, as shown. 4. Lower the removal tool toward the bottom, and pull out the unit halfway while pressing towards the inside.

Be careful to avoid injury from the catch pins on the removal tool.
Removal Tool (Accessory 7)
5. Pull the unit all the way out with your hands, being careful not to drop it.
Installation of Remote control unit
Install the remote control unit holder (Accessory @).
Double-stick tape (included)

Remote control holder @

To prevent the Remote control unit from dropping down under your foot, install it using the Remote control unit holder.If the Remote control unit drops down under driving pedals, it will interfere with your driving and may result in a traffic accident.