LZ-702IR
WIDE SCREEN MONITOR 3 page 2 - 12

INSTRUCTION MANUAL

MONITEUR ECRAN LARGE 3 page 14 - 24

MODE DEMPLOI

BREITBILD MONITOR 3 Seite 26 - 36

BEDIENUNGSANLEITUNG

BREEDBEELD MONITOR 3 blz 38 - 48

GEBRUIKSAANWIJZING

MONITOR CON SCHERMO PANORAMICO 3 pagina 50 - 60

ISTRUZIONI PER LUSO

MONITOR DE PANTALLA PANORMICA 3 pgina 62 - 72

MANUAL DE INSTRUCCIONES

MONITOR DE ECR LARGO 3 pgina 74 - 84

MANUAL DE INSTRUES

- 96

B64-3413-00/00 (WV)

Safety precautions

2 WARNING

To prevent injury or fire, take the following precautions:
To prevent a short circuit, never put or leave any metallic objects (such as coins or metal tools) inside the unit. Do not watch or fix your eyes on the units display when you are driving for any extended period. Mounting and wiring this product requires skills and experience. For safetys sake, leave the mounting and wiring work to professionals. Do not touch the liquid crystal fluid if the LCD is damaged or broken due to shock. The liquid crystal fluid may be dangerous to your health or even fatal. If the liquid crystal fluid from the LCD contacts your body or clothing, wash it off with soap immediately.

2 CAUTION

To prevent damage to the machine, take the following precautions:
Make sure to ground the unit to a negative 12V DC power supply. Do not install the unit in a spot exposed to direct sunlight or excessive heat or humidity. Also avoid places with too much dust or the possibility of water splashing. When replacing a fuse, only use a new fuse with the prescribed rating. Using a fuse with the wrong rating may cause your unit to malfunction. Do not use your own screws. Use only the screws provided. If you use the wrong screws, you could damage the unit.

English

If you experience problems during installation, consult your Kenwood dealer. When you purchase optional accessories, check with your Kenwood dealer to make sure that they work with your model and in your area. If the unit fails to operate properly, press the Reset button. The unit returns to factory settings when the Reset button is pressed.
Screen brightness during low temperatures
When the temperature of the unit falls such as during winter, the liquid crystal panels screen will become darker than usual. Normal brightness will return after using the monitor for a while.

PWR OFF

IR MODE

AV OUT

SELECT
Information on Disposal of Old Electrical and Electronic Equipment (applicable for EU countries that have adopted separate waste collection systems)
Products with the symbol (crossed-out wheeled bin) cannot be disposed as household waste. Old electrical and electronic equipment should be recycled at a facility capable of handling these items and their waste byproducts. Contact your local authority for details in locating a recycle facility nearest to you. Proper recycling and waste disposal will help conserve resources whilst preventing detrimental effects on our health and the environment.
Reset button Even if the Reset button is pressed, values set for individual items are not cleared. To initialize set values, perform the operation mentioned in <Initializing the User Settings> (page 7). The illustrations of the display and the panel appearing in this manual are examples used to explain more clearly how the controls are used. Therefore, what appears on the display in the illustrations may differ from what appears on the display on the actual equipment, and some of the illustrations on the display may represent something impossible in actual operation.

Cleaning the Unit

If the faceplate of this unit is stained, wipe it with a dry soft cloth such as a silicon cloth. If the faceplate is stained badly, wipe the stain off with a cloth moistened with neutral cleaner, then wipe it again with a clean soft dry cloth.
Applying spray cleaner directly to the unit may affect its mechanical parts. Wiping the faceplate with a hard cloth or using a volatile liquid such as thinner or alcohol may scratch the surface or erases characters.

English |

Operations

IR transmitter LED

V.SEL SCRN MODE

Auto Dimmer sensor

Turning ON the Power Press the [SCRN] button. Turning OFF the Power Press the [SCRN] button for at least 1 second.

Switching Screen mode

Press the [MODE] button. Each time the button is pressed, the screen mode switches as follows: Display "Full" Setting Full picture mode.

Video Source Selection

Press the [V.SEL] button. Each time the button is pressed, the video source switches as follows: Display "AV-IN1" "AV-IN2" Setting Select the AV1 INPUT source. Select the AV2 INPUT source.

"Just"

Justify picture mode.

"Cinema"

Cinema picture mode.

"Zoom"

Zoom picture mode.

"Normal"

Normal picture mode.
IR Headphones audio setting
You can select the IR Headphones audio you wish. Press the [MODE] button for at least 1 second. Each time the button is pressed for at least 1 second, the audio input switches as follows: Display "Normal" "AV-IN1" "AV-IN2" "Off" Setting Sound with monitor source. Select the AV1 INPUT source. Select the AV2 INPUT source. No output to IR Headphones.

2 Adjusting the item

Press the [2] or [3] button. Item "BRT" "TIN" "COL" "CONT" "BLK" Button [3] [2] [3] [2] [3] [2] [3] [2] [3] [2] Setting Brighter screen Darker screen Stronger red level Stronger green level Deeper color Paler color Stronger contrast Less contrast Less black level Stronger black level
Turn off the headphones before changing the <IR Headphones audio setting>.
Auto Dimmer Item "Auto DIM" Button [3] [2] Setting The display doesn't dim. When it gets dark, the brightness of display lowers automatically.
Swithing the Display off mode
You can set the display off mode for the monitor. Press the [V.SEL] button for at least 1 second. Exit the Display off mode Press any button. Press the button other than the [2] and [3] buttons.
3 Exit Picture Quality setting mode

Press the [MODE] button.

The "BRT" can be adjusted when "Auto DIM" is set to "Off". The "TIN" can be adjusted when NTSC video signal is input. The screen select can be set for each source. If you make no operation for 15 seconds, this mode is automatically canceled.

Picture Quality setting

You can adjust the picture quality and Auto dimmer control of the monitor.
1 Select the adjusting item
Press the [SCRN] button. Each time the button is pressed, the adjusting item switches.

Setting the AV Output

Selects an AV source to be output at the "AV OUTPUT" terminals. Press the [MENU] button for at least 1 second. Each time the button is pressed for at least 1 second, the AV output switches as follows: Display "AV-IN1" "AV-IN2" "Off" Setting Select the AV1 INPUT source. Select the AV2 INPUT source. No output to the AV OUTPUT terminals.

Setup Menu

Menu System
The Menu system operation method is explained here. The reference for the Menu items and their setting content is after this operation explanation.

1 Enter Menu mode

Press the [MENU] button. Menu screen is displayed, and the monitor enters to Menu mode. Current menu item
AV-OUT IR HEADPHONE Surround Frequency AV-IN1 Normal On 2MHz

Display information

When you press the [V.SEL] button, the status of the monitor is displayed.

3 AV-IN2

2 Select the menu item
Press the [MENU] button. Each time the button is pressed, the menu item switches.

3 Set the menu item

Press the [2] or [3] button. You can continue by returning to step 2 and setting other items.

Mode Full

A V AV-IN1

4 Exit Menu mode

1 Screen mode Display 2 IR Headphones audio setting Display 3 Video source Display 4 AV output Display
You can select "Surround" and "Frequency" when <IR HEADPHONE> is not set to "Off". If you make no operation for 15 seconds, this mode is automatically canceled.
The information display is cleared automatically after approximately 5 seconds.
Selects an AV source to be output at the "AV OUTPUT" terminals. Display "AV-IN1" "AV-IN2" "Off" Setting Select the AV1 INPUT source. Select the AV2 INPUT source. No output to the AV OUTPUT terminals.
Initializing the User Settings
The setting value is set to the initial state of factory.
1 Select the Memory clear mode

Memory Clear Yes No

You can select the IR Headphones audio you wish. Display "Normal" "AV-IN1" "AV-IN2" "Off" Setting Sound with monitor source. Select the AV1 INPUT source. Select the AV2 INPUT source. No output to IR Headphones.

2 Set the Memory clear

Press the [2] button. "System Settings were Initialized" is displayed.
When you cancel this function, press the [3] button.

3 Exit Menu mode Surround Control
Turns the surround control function On or Off. Display "On" "Off" Setting The surround control function is On. The surround control function is Off. Press the [MODE] button.

Frequency Setting

You can set to IR Headphones transmitter frequency. Display "2MHz" "3MHz" Setting Set to 2MHz. Set to 3MHz.
Refer to the instruction manual of IR Headphones (optional accessory), when setting for frequency.
Accessories/ Installation Procedure
Accessories 1 Installation Procedure
1. To prevent short circuits, remove the key from the ignition and disconnect the terminal of the battery. 2. Make the proper input and output cable connections for each unit. 3. Connect the wiring harness wires in the following order: ground, ignition. 4. Connect the wiring harness connector to the unit. 5. Install the unit in your car. 6. Reconnect the terminal of the battery. 7. Press the reset button. (page 3)
This product is intended for use with 12V DC negative ground power only. Do not connect it to any other power supply. To prevent shorting, disconnect the battery cable from the negative terminal of the battery during installation. Be sure to firmly stabilise this product. Do not install it in a location which is not stable. Follow the installation and wiring procedures described in this manual. Improper wiring or modified installation can not only result in malfunction or damage to the unit but may also result in an accident. If your cars ignition does not come with an ACC position, connect the ignition wires to a power source that can be turned on and off with the ignition key. If you connect the ignition wire to a power source that receives a constant voltage supply, as with battery wires, the battery may die. If the fuse blows, first make sure that the wires have not caused a short circuit, then replace the old fuse with one with the same rating. Do not let unconnected wires or terminals touch metal on the car or anything else conducting electricity. To prevent short circuits do not remove the caps from unused terminals or from the ends of the unconnected wires. After the unit is installed, check whether the brake lamps, blinkers, wipers, etc. on the car are working properly. Insulate unconnected wires with vinyl tape or other similar material. Thoroughly wipe away oil and other dirt from the installation surface. Please avoid installation on uneven surfaces. Do not install the Hideaway Unit under the carpet. Otherwise heat build-up occurs and the unit may be damaged.

Connection

Monitor Unit

FM/AM ANTENNA

Accessory 2

Hideaway Unit

VIDEO AV 1 INPUT L (MONO) AV 2 INPUT VIDEO L R VIDEO R AV OUTPUT L R

Audio/Visual input 1

Visual input (Yellow) Audio left input (White) Audio right input (Red)

Audio/Visual Output

Visual output (Yellow) Audio left output (White) Audio right output (Red) Accessory 1

Audio/Visual input 2

Ignition key switch ACC Ignition cable (Red)

( 5A )

Car fuse box (Main fuse)
Ground cable (Black) (To car chassis)
Battery Reverse sensor cable (Purple/White) Not used

REVERSE

Not used
Parking sensor cable (Light Green)

PRK SW

TO MONITOR

Installation

Installation for Monitor Unit
Mounting and wiring this product requires skills and experience. For safety's sake, leave the mounting and wiring work to professionals. Before mounting the monitor to the headrest: Perform the required external connections first (Accessory 2). Using the supplied paper pattern (Accessory 5), mark the area to be cut out of the headrest, then carefully cut it. 1. Connect Monitor and system cord (Accessory 2). 2. Install the monitor unit in the bracket (Accessory 4).

Headrest

Installation plate (not supplied) Accessory 2 Accessory 4 Monitor Unit
Paper template (Accessory 5)

Screws (not supplied)

Installation for Hideaway Unit
Use screws (Accessory 3) to fix Hideaway Unit onto an audio board or another.

Accessory 3

Troubleshooting Guide
Removing the Monitor Unit 1 Insert the removal tool (Accessory 6) deeply
into the slots on each side, as shown. What might seem to be a malfunction in your unit may just be the result of slight misoperation or miswiring. Before calling service, first check the following table for possible problems.
The power does not turn on. The fuse has blown. After checking for short circuits in the wires, replace the fuse with one having the same rating. No ACC position on vehicle ignition. Connect the same wire to the ignition as the battery wire. Nothing happens when the buttons are pressed. The computer chip in the unit is not functioning normally. Press the reset button on the unit (page 3). The screen is dark. The unit is in a location where temperature is low. If the temperature of the monitor unit drops, the screen may appear darker when power is first turned on due to the characteristics of a liquid crystal panel. Wait a while after turning power on for the temperature to rise. Normal brightness will return. No sound from wireless headphones. IR Headphones setting is "Off". Turn it "On" (page 6). The frequency setting is not set correctly. Select the transmitter frequency according to your headphones. The headphones power is off. The headphones power switch is turned on. The headphones batteries are exhausted. Replace the headphones batteries with fresh ones.

[MENU]
AV-OUT IR HEADPHONE Surround Frequency

AV-IN1 Normal On 2MHz

IR AV

[2] [3] 2

IR HEADPHONE "Off" "Surround" "Frequency" 15
"AV OUTPUT" AV "AV-IN1" "AV-IN2" "Off" AV1 INPUT AV2 INPUT AV OUTPUT
IR "Normal" "AV-IN1" "AV-IN2" "Off" AV1 INPUT AV2 INPUT IR
[2] "System Settings were Initialized"
"On" "Off"
IR "2MHz" "3MHz" 2MHz 3MHz
1. 2. 3. 4. 5. 6. 1 7. 87

1..1 2..1 3..2

12V DC ACC ON/OFF

4..1 5..1 6..1

1. 2 2. 4

ACC

87 IR "Off" "On" IR90
: 6.95 156.2(W) 82.4(H) 176.0() mm : TN LCD : TFT : 336,960 (480 H 234 V RGB) : 99.99 % : RGB : IR :2MHz2.3 MHz/ 2.8MHz :3MHz3.2 MHz/ 3.8MHz
: 14.4 V DC (11 V 16 V) : 1.5 A : 14 W : -10 +60 : -30 +85 (WHD) : 34 mm : 99 mm : 440 g : 380 g
: NTSC/PAL RCA : 1 0.1 Vp-p/ 75 RCA : 1 V/ 55 K RCA : 1 0.1 Vp-p/ 75 RCA : 1 V/ 1 K

99.99%0.01%