Reviews & Opinions
Independent and trusted. Read before buy Kenwood TS950SDX!

Kenwood TS950SDX

Manual

Download (English)
Instruction: After click Download and complete offer, you will get access to list of direct links to websites where you can download this manual.

About

Kenwood TS950SDXAbout Kenwood TS950SDX
Here you can find all about Kenwood TS950SDX like manual and other informations. For example: review.

Kenwood TS950SDX manual (user guide) is ready to download for free.

On the bottom of page users can write a review. If you own a Kenwood TS950SDX please write about it to help other people.

 

[ Report abuse or wrong photo | Share your Kenwood TS950SDX photo ]

Video review

Kenwood TS 950SDX

 

User reviews and opinions

<== Click here to post a new opinion, comment, review, etc.

No opinions have been provided. Be the first and add a new opinion/review.

 

Documents

doc1

PIEXX DRU-2 px Installation Instructions
The PIEXX DRU-2 px is a physical and electrical replacement for the original Kenwood DRU-2 Digital Voice Recorder. Dont you wish those PLAY and RECORD buttons worked on your Kenwood TS-850 transceiver? They would if you had bought the DRU-2 option board. The original Kenwood part is nearly impossible to get, but now PIEXX is manufacturing a replacement DRU-2px board. Best of all, with the PIEXX board the three messages are each 32 seconds long!
DRU-2 px Installation in the Kenwood TS-850 transceiver.
1. Open the cover panel on the top left of your TS-850 transceiver. 2. Position the DRU-2px board as shown in the picture below. Notice that the DRU-2px board is held in place on the top left side by a hook in the sheet metal on the TS-850 chassis. Secure the DRU-2 px in place with the #4 sheet metal screw and lock washer provided. The lock washer should be positioned between the head of the screw and the top side of the DRU-2 px board. 3. Align and install the 5-position connector (only 4 leads) coming from the bottom left of the DRU-2 px board, with connector CN501. The black side of the connector, installed in CN501 will be facing the DRU-2 px board.
4. Find the IDC 14-pin cable that was shipped with the DRU-2 px board. Notice that it has a 10 position and a 8 position 1.5 mm plug on one side of the cable. Each of these 1.5mm plugs has a side that is painted black. The 10 position plug should be installed in CN502 with the black side facing the CN502 screened on the board. Verify this installation in the picture below.
5. Now, install the 8 position 1.5mm connector into the socket marked CN503. The black side of the connector will face the silkscreen marking CN507.
6. Next, install the 14 position IDC connector on the 14 pin header marked J2 on the DRU-2 px board. Be sure that the connector is aligned with the header pins. It is going to be very close to the right side of the sheet metal cutout on the TS-850 access door.
DRU-2px Installation in the Kenwood TS-950SDX transceiver.
1. Open the cover panel on the top left of your TS-950SDX transceiver. 2. Find the IDC 14-pin cable that was shipped with the DRU-2 px board. Notice that it has a 10 position and a 8 position 1.5 mm plug on one side of the cable. Each of these 1.5mm plugs has a side that is painted black. The 10 position plug should be installed in CN104 with the black side facing the CN104 screened on the board. Verify this installation in the picture below. 3. Install the 8 position 1.5mm connector into the socket marked CN103. The black side of the connector will face the silkscreen marking CN103.
4. Align and install the 5-position connector (only 4 leads) coming from the bottom left of the DRU-2 px board, with connector CN102. The black side of the connector will face the silkscreen marking CN102.
5. Position the DRU-2px board as shown in the picture below. Notice that the DRU-2px board is held in place on the top left side by a hook in the sheet metal on the TS-950SDX chassis. Secure the DRU-2 px in place with the #4 sheet metal screw and lock washer provided. The lock washer should be positioned between the head of the screw and the top side of the DRU-2 px board.
7. Reinstall the access cover on your TS-950SDX transceiver. Installation is now complete.

Operation

The operation of the PIEXX DRU-2 px is the same as the original DRU-2 so the instructions in your TS-850 manual apply. The DRU-2 px has three 32 second message buffers so you might as well change the REC 1, REC 2 and REC 3 recording times to the longest value. These parameters are set as indicated in the Power on function selection section of the owners manual on page 35, but here is a quick review: 1. Turn off your TS-850 transceiver. 2. Press and hold the LSB / USB key, and while holding this key turn the transceiver back on. 3. Rotate the M.CH / VFO CH knob to select parameter # 29 as indicated on the main display. Press the UP button to change this parameter to 16, the maximum value it can be changed to. 4. Next rotate the M.CH / VFO CH knob to select parameter # 30 as indicated on the main display. Press the UP button to change this parameter to 16, the maximum value it can be changed to. 5. Next rotate the M.CH / VFO CH knob to select parameter # 31 as indicated on the main display. Press the UP button to change this parameter to 32, the maximum value it can be changed to. 6. Exit the Power on function selection mode by pressing the CLR button on your transceiver. You can also exit by turning the radio off. Even though you can only set REC 1 and REC 2 to 16 seconds, these memory locations can, and will hold 32 seconds of speech. The display will count down from 16 to 0, while recording and then continue to stay on 0 until the 32 second record buffer is full as indicated by the CW character AR being announced from the speaker. In order for the Voice recorder functions to operate, the TS-850 must be in a voice mode either SSB, AM or FM. To record a message: 1. Pres REC-1, or REC-2 or REC-3 depending on which buffer you would like to record to. The TS-850 will announce the CW character BT, and the display will show AP1 - , AP 2 - ,or AP 3 -. 2. When you are ready to start recording your message, press and hold the same REC button you initiated the recording sequence with in step 1 above. 3. Speak into the mic in a normal voice. There is no need to press, nor should you, the PTT button on the hand mic. The TS-850 should not be in the transmit mode while you are recording!

4. The record session will be completed when you release the REC button you are holding. The display will return to the normal frequency readout. To listen to the message you recorded: 1. Turn the MONI control up to a convenient listening level. Make sure that the VOX feature is not engaged. 2. Press the PLAY-1, PLAY-2 or PLAY-3 button. Adjust the playback volume with the MONI control. 3. The playback will stop when the message completes, or you can stop playback with the CLR button. To transmit a saved message, either go to the SEND mode, by pressing the SEND button, or enable the VOX system. Press one of the PLAY buttons. Set the transmit level with the MIC control. You can stack the messages to be transmitted, up to 3 levels, by pressing another PLAY button while a message is playing. The next message, or the same one for that matter, will start as soon as the previous message completes. You can terminate the message playback by pressing the CLR button. The mic is still enabled while a message is playing, so be quiet!

 

Tags

Olympus EP-2 Canon F1 Galeo 5065 9 0 RMX 2450 XS-LD125p5 Quick-O NVX-G100 DMC-FS9 DI181 Isight 650 ABS Inter-TEL 8500 KDL-40EX701 SR-L36nebs Scenic DSC-H2 Facebook Hdchs100 Series Evolution V14 FP241W SA-TX50 5014068 Rings RHT398H IHF1000 Scanner 21PT1542 CF-360 Cherokee 495 WNR834M Oximo WT 20F511T ADB340MP TX81Z 42PD7200 M183DN Intermatic DT17 Keyboard MM-N4 Na-ittl Lunasix F WA12V9 IRC3580-J1 TC-WE705S Mercenaries LC-32RD8E Louie CDX-M770 Yamaha MU50 373LM 3 0 URC 1001 Ixus 210 EL-6900 ESF 2440 DVA-G3340S SDM-M81 Vivicam 3345 XSU-01220B GDI21 HT-DM150 GV-650 RB-993 M10-IT Bedienmodul HL-5030 Sherpa Digidice Review Ypg-235 Hitman 2 LE46A556 PZ-1P Sg520 TA-VA80ES Meter Factor PC DMC-FZ3 Part2 Witl 66 Studio WG311T 4 Mkii ZI720 9K WA13UP MDR-EX700LP KR7A-raid LE-32S81B RR61L Projectors MHC7900 Shield KM-4850W Keytronic 2000 SRE Coolpix L19 RTX-2007 NK50V Rcs-55

 

manuel d'instructions, Guide de l'utilisateur | Manual de instrucciones, Instrucciones de uso | Bedienungsanleitung, Bedienungsanleitung | Manual de Instruções, guia do usuário | инструкция | návod na použitie, Užívateľská príručka, návod k použití | bruksanvisningen | instrukcja, podręcznik użytkownika | kullanım kılavuzu, Kullanım | kézikönyv, használati útmutató | manuale di istruzioni, istruzioni d'uso | handleiding, gebruikershandleiding

 

Sitemap

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101