Connecting the power

RISK OF ELECTRIC SHOCK: Use only the AC power adapter included with your printer dock. Other adapters or cords can damage your camera, printer dock, or computer. 1 Remove the camera from the printer dock. 2 Connect the AC power cord to the AC power adapter, then to the back of the printer dock. NOTE: The AC power cord included with your printer dock may not require assembly, and may be different from the one shown. 3 Connect the AC power cord into a power outlet. Purchase an AC power cord and other accessories at www.kodak.com/go/accessories.
Handling and storing the color cartridge
For best quality prints, store the color cartridge in a location where the temperature does not exceed 85 F (30 C). To avoid getting fingerprints on the ribbon, handle the color cartridge by the spool ends. Keep the color cartridge away from direct sunlight and out of high-temperature environments (such as a vehicle parked in the sun).
Installing and removing the color cartridge
1 Open the cartridge door on the side of the printer dock. 2 Check to make sure there is no slack in the color cartridge ribbon. To remove slack, push in on the cartridge spool, then rotate the spool clockwise. IMPORTANT: Be careful not to rotate the spool more than necessary. Doing so could reduce the number of prints you are able to make. 3 Slide the color cartridge in, label side up, with the arrow pointing toward the printer dock. Push the cartridge until it "clicks" into place. 4 Close the cartridge door.
IMPORTANT: The color cartridge may lock in place if there is a paper error. Do not attempt to remove the cartridge without first clearing the paper error. Make sure the Paper light is off before attempting to remove the cartridge (see Paper light under Printer dock status lights, page 41). To remove the color cartridge, open the color cartridge door, then push up on the green lever and slide the cartridge out.
When the cartridge is almost empty, the Color cartridge light blinks slowly for several seconds. When the cartridge is depleted, the Color cartridge light glows steady amber. After installing a new color cartridge, press the Print button to clear the cartridge error and resume printing.
Handling and storing the paper
To avoid fingerprints, handle the paper by the edges or by the perforated tabs. Do not touch the glossy side of the paper. When storing, remove the paper tray, then close the paper tray cover and paper tray door to keep out dust and debris. Store paper flat.

The charging lights monitor the refresh status:
Descending blinking Discharging battery pack (lights turn off as green lights discharging progresses). Ascending steady green lights Charging battery pack (lights turn on as charging progresses). Charging is complete when all three lights are lit.
Setting the picture quality
Before taking pictures, change the picture quality setting (or resolution) on your digital camera to 3:2. This ensures that the pictures you take are proportional to the printer dock paper, preventing unwanted cropping of your pictures. See your camera users guide for more information.
Tagging pictures for printing
NOTE: The following procedure pertains to Kodak EasyShare digital cameras. For information on tagging pictures on other brands of ImageLink system compatible cameras, see the camera users guide. 1 Press the Share button. 2 Press to locate a picture. 3 Make sure Print is highlighted (to tag all pictures in the current image storage location, highlight Print All ), then press the OK button. 4 Press to select the number of copies (0 - 99). The default is one. Zero removes the tag for a selected picture. The Print icon is displayed in the status area.
To apply a print quantity to other pictures, press the print quantity as is, or press to change it.

to locate them. Keep

5 Press the OK button. 6 Press the Share button to exit. NOTE: To remove print tagging from all pictures: from the Share menu, highlight Cancel Prints press the OK button. To print tagged pictures from your digital camera, see page 15. To print tagged pictures from your computer, see page 26. 12

, then

Printing without a computer
IMPORTANT: Wait until printing is complete before removing paper, the paper tray, or the camera. Failure to do so can cause paper misfeeds or jams.
Printing from your digital camera
1 Take a picture with your camera (see your camera users guide). 2 Place the camera on the printer dock (see page 10). The current or most recent picture appears on the camera screen.
To print the current picture, press the Print button,
NOTE: If you tagged pictures for printing using your digital camera, instead of printing the current picture, all tagged pictures are printed (see page 15).
Press the Left/Right control on the printer dock, pictures to print.

to review and choose

3 Press the Print button, The copy screen appears.
To print more than one copy, press press.
to select the number of copies, then
(If you dont press any buttons, after 10 seconds printing starts automatically.) The Print light blinks, and printing starts.The paper cycles four times during the printing process before the finished print is ejected. The first three passes apply layers of yellow, magenta, and cyan colors to the print, and the fourth pass applies the Kodak XtraLife coating that protects and preserves the image.

Printing from a Kodak card reader
The Kodak EasyShare printer dock series 3 is compatible with the Kodak 8-in-1 card reader and the Kodak 6-in-1 card reader (each sold separately). Other Kodak USB card readers may work with the printer dock; however, other manufacturers card readers are not supported. 1 For best results, tag pictures on your memory card for printing (see page 12 or your camera users guide). If you do not tag pictures on your memory card, you will have the option of printing only the most recent picture on the card. 2 Plug the USB connector from the card reader into the USB connector located on the side of the printer dock. NOTE: If the card reader is already plugged in but the connection is no longer available, disconnect then reconnect the USB cable to re-establish the connection. 3 Insert the memory card into the card reader (see your card reader users guide for details). Do not insert more than one card at a time. 4 Press to begin printing, or press to cancel. Purchase a Kodak card reader and other accessories at a retailer of Kodak products, or visit www.kodak.com/go/accessories.

Printing tagged pictures

If your camera or memory card contains pictures tagged for printing (see page 12 or your camera users guide), the printer dock gives you the option to print tagged pictures first. If your camera is docked, a message appears on the camera screen indicating that tagged pictures have been found:
To print tagged picturespress. The Print light blinks, printing starts, and tagged pictures are printed. Print tags are removed from tagged pictures on your camera or card as they are printed. To bypass printing of tagged picturespress.
The message disappears after 10 seconds of inactivity.
Printing from a PictBridge compatible device
The Kodak EasyShare printer dock series 3 offers PictBridge technology, which lets you print from any PictBridge compatible camera or device. 1 Plug the USB connector from the PictBridge compatible device into the USB device connector located on the side of the printer dock. NOTE: If the PictBridge compatible device is already plugged in but the connection is no longer available, disconnect then reconnect the USB cable to re-establish the connection.
2 Use your PictBridge compatible device to review pictures, choose printing options, and print. See your device users guide for details.
Changing the printed picture size
1 Follow the procedure for printing from your digital camera (see page 13), Kodak card reader (see page 14), or PictBridge compatible device (see page 15). 2 Before printing, while making selections or changing settings, press the Picture Size button repeatedly to scroll through and select a picture size.
Picture Size setting 1 up (full photo) 2 up (card size) 4 up (wallet size) 9 up (mini photo) Number and size of prints per sheet One 4 x 6 in. (102 x 152 mm) picture Up to two 2.1 x 3.3 in. (54 x 85 mm) pictures Up to four 2 x 3 in. (51 x 76 mm) pictures Up to nine 1.3 x 2 in. (34 x 51 mm) pictures

3 Continue changing other settings or begin printing. To change the default picture size:
Select a picture size (see above), then press and hold the Picture Size button for 4 seconds. The selected Picture Size light blinks, then glows steady.
Effect of picture size on number of copies
In most cases, the picture size setting also determines the number of copies that are printed. For example, if you choose to print a picture with 2 up selected, 2 copies are printed on one sheet of paper. When printing tagged pictures (see page 15), the number of copies that are printed is determined by the setting on your camera or device. For example, if three pictures on your camera are each tagged for printing one copy, and the 4 up option on the printer dock is selected, three 2 x 3 in. (51 x 76 mm) pictures are printed on one sheet of paper. For best results, choose a picture size or number of copies (on your camera or device) that optimizes the use of white space on the paper. 16
NOTE: When printing from a PictBridge compatible device (see page 15), picture size and number of copies are determined by the devices multi-up and copies settings. Change these settings on your device before printing. If the picture size option selected on your device does not match any of the picture size options on the printer dock, the closest available picture size option on the printer dock is automatically selected.
Printing different pictures on the same sheet
1 Tag the pictures you want to print on your digital camera (see page 12). 2 Place the camera on the printer dock, or insert the memory card into a connected Kodak 8-in-1 or 6-in-1 card reader (sold separately). If your camera is docked, a message appears on the camera screen indicating that tagged pictures have been found. 3 Press the Picture Size button repeatedly to scroll through and select either 2 up , 4 up , or 9 up , depending on the picture size you wish to print (see page 16). 4 Press to begin printing. NOTE: If you select more than one copy of a picture when tagging them on your camera, duplicate pictures are printed on the same sheet (see below).

Printing duplicate pictures on the same sheet
Method 1: by setting it up on your digital camera 1 Tag the pictures you want to print on your digital camera (see page 12). For each picture, choose the number of copies you would like to print. 2 Place the camera on the printer dock, or insert the memory card into a connected Kodak 8-in-1 or 6-in-1 card reader (sold separately). If your camera is docked, a message appears on the camera screen indicating that tagged pictures have been found. 3 Press the Picture Size button repeatedly to select either 2 up , 4 up , or 9 up , depending on the picture size you wish to print (see page 16). 4 Press Method 2: using the printer dock Place the camera on the printer dock, or insert the memory card into a connected Kodak 8-in-1 or 6-in-1 card reader (sold separately). The current or most recent picture appears on the camera screen.

to begin printing.

Press the Left/Right control on the printer dock, picture to print.

to review and choose a

5 Press the Print button, The copy screen appears.
to select the number of copies, then press
(If you dont press any buttons, after 10 seconds printing starts automatically.)

Canceling printing

Press and hold for 2 seconds. The print job is canceled and ejected from the printer dock. If you cancel a print during the fourth pass (clear coat), the print is ejected upon completion. NOTE: Using the Print button to cancel a print job only works when printing from a docked camera.
Removing the perforated tabs from the paper
IMPORTANT: Remove perforated tabs only after printing. Paper missing perforated tabs will not feed properly. 1 Fold the tabs up, then down. 2 Remove each tab and discard.

Installing software

Macintosh computers
Power Mac G3, G4, G5, G4 Cube, iMac;
Minimum system requirements
Windows OS-based computers
Windows 98, 98SE, ME, 2000 SP1, or
XP OS Internet Explorer 5.01 or higher 233 MHz processor or greater 64 MB RAM (128 MB RAM for Windows XP OS) 200 MB hard disk space available CD-ROM drive Available USB port Color monitor, 800 x 600 pixels (16-bit or 24-bit recommended)
PowerBook G3, G4; or iBook computers
Mac OS 10.2 or higher Safari 1.0 or higher for complete installation 128 MB RAM 200 MB hard disk space available CD-ROM drive Available USB port Color monitor, 1024 x 768 pixels (thousands

Using the printer dock with a computer

Connecting to a computer

IMPORTANT: Make sure your camera is NOT docked when you connect the printer dock to the computer. 1 Make sure Kodak EasyShare software is installed on the computer (see page 20). 2 Plug the labeled end of the USB cable (included) into the labeled USB port on your computer. See your computer documentation for details. 3 Plug the other end of the USB cable into the square USB connector on the back of the printer dock.
Transferring pictures from your digital camera
1 Make sure Kodak EasyShare software is installed (see page 20) and the printer dock is connected to your computer (see page 23). 2 If you have the optional USB card reader, disconnect it from the printer dock. 3 Place the camera on the printer dock (see page 10). 4 Press the Transfer button, , on the printer dock. Kodak EasyShare software opens on your computer (if it is installed). 5 Use Kodak EasyShare software to transfer pictures from the camera to your computer. See the Kodak EasyShare software Help for details. The printer dock Transfer light blinks while the pictures are being transferred. The Transfer light continues to blink until the Transfer or Print button is pressed, the camera is removed from the printer dock, or the connection is no longer available. NOTE: With the software installed, pressing the Transfer button establishes a new drive connection for the docked camera. You can view, copy, delete, and otherwise manage files on the new drive, as you do with other drives on your computer. See your computer documentation for details.
Transferring pictures from a Kodak card reader
The Kodak EasyShare printer dock series 3 is compatible with the Kodak 8-in-1 card reader and the Kodak 6-in-1 card reader (each sold separately). Other Kodak USB card readers may work with the printer dock; however, other manufacturers card readers are not supported. 1 Make sure Kodak EasyShare software is installed (see page 20) and the printer dock is connected to your computer (see page 23). 2 If a camera is docked, remove it. 3 Plug the USB connector from the card reader into the USB connector located on the side of the printer dock. NOTE: If the card reader is already plugged in but the connection is no longer available, disconnect then reconnect the USB cable to re-establish the connection. 4 Insert the memory card into the card reader (see your card reader users guide for details). Do not insert more than one card at a time. 5 Press the Transfer button, , on the printer dock. Kodak EasyShare software opens on your computer (if it is installed). 6 Use Kodak EasyShare software to transfer pictures from the card reader to your computer. See the Kodak EasyShare software Help for details. The printer dock Transfer light blinks while the pictures are being transferred. The Transfer light continues to blink until the Transfer or Print button is pressed, or until the connection is no longer available. NOTE: With the software installed, pressing the Transfer button establishes one or more new drive connections for the card reader. You can view, copy, delete, and otherwise manage files on the new drives, as you do with other drives on your computer. See your computer documentation for details. Purchase a Kodak card reader and other accessories at a retailer of Kodak products, or visit www.kodak.com/go/accessories.

Change the picture quality setting (or resolution) on your digital camera
to 3:2. See your camera users guide for details. Adjust cropped pictures using Kodak EasyShare software on your computer. If you are printing from an application on your computer, select the proper paper size in print options.
NOTE: Cropping may vary depending on the selected picture size (page 16).
A selected The image file may be corrupt. Review the picture on the camera or computer and delete if necessary. picture does not print. The image file may not be JPEG format. The printer dock can only print JPEG files in standalone mode. Connect to a computer (page 23) and use EasyShare software to print BMP and TIFF formats (page 26).
If. Nothing happens when you try to print Try the following
Check the power connections (page 3). Remove the paper tray, check that paper is properly loaded, and re-install

(page 7).

If the Paper light glows steady amber, load paper (page 6). Make sure the color cartridge is properly installed (page 4). If the Color
cartridge light is on, install a new cartridge. on the printer dock (page 10). printer dock.
Nothing happens when you try to print (from docked camera) Nothing happens when you try to print (from Kodak card reader)
The camera is not properly seated on the connector. Reseat the camera Re-establish the connection: remove, then reseat the camera on the Make sure there is at least one picture in the cameras internal memory

or memory card.

NOTE: The Kodak EasyShare printer dock series 3 is compatible with the Kodak 8-in-1 card reader and the Kodak 6-in-1 card reader (each sold separately). Other Kodak USB card readers may work with the printer dock; however, other manufacturers card readers are not supported.
Check the USB connections from the card reader to the printer dock

(page 14).

Re-establish the connection: disconnect, then reconnect the USB cable
from the card reader to the printer dock. Make sure a memory card is inserted and that there is at least one picture on the memory card.
Nothing Check the USB connections from the PictBridge compatible device to the printer dock (page 15). happens when you try to print Re-establish the connection: disconnect, then reconnect the USB cable from the PictBridge compatible device to the printer dock. (from PictBridge compatible Make sure there is at least one picture in the PictBridge compatible device) devices internal memory or memory card.
Nothing Check the USB connections from the printer dock to the computer (page 23). happens when you try to print The computer may be transferring pictures. Wait a few seconds, then try to again. (from computer) Access the printer menu for your system. Remove check marks next to Pause Printing and Offline, if checked. Close unnecessary software applications. Disconnect then reconnect the USB cable from the printer dock to the computer (page 23). Make sure Kodak EasyShare software is installed (page 20). Install if necessary. If you choose Custom installation, make sure to install the printer driver. Uninstall, then reinstall Kodak EasyShare software (page 20). Make sure your computer meets the minimum system requirements (page 20). Upgrade your system if necessary. Printing is slow NOTE: When printing a large number of prints, printing may slow down to prevent the

Battery charging lights Light status All lights are off Cause The camera may not be properly seated on connector. The camera is turned on. An unrecognized battery type is installed, or camera does not support charging. Action/solution Reseat the camera on the printer dock (page 10). Turn off the camera. Install a Kodak EasyShare Ni-MH rechargeable battery pack or Kodak EasyShare Li-Ion rechargeable battery (page 8). See your camera users guide for other charging options. None; dock is checking the charge status of the battery.
One steady green light The camera was just placed in camera dock. Ascending steady green lights
The battery is charging. Charging Leave the camera on the dock to is complete when all three lights continue charging or maintain are lit. charge.
One blinking red light The battery is not properly installed. The battery or connector pin is damaged.
Re-install the battery. Check for damage.
The camera and battery have been Slowly return the camera and exposed to extreme temperatures. battery to room temperature. Descending blinking green lights The Ni-MH battery pack refresh cycle in progress: discharging (lights turn off as discharging progresses). Leave the camera on the dock to continue refresh cycle (page 11).
Print button/light Light status Light glows steady green Light blinks green Light is off Cause The printer dock is ready for printing. The printer dock is printing. There are no pictures in the camera or on the card. None required. To enable Print: 1 Take pictures. Action/solution None required.
The camera is not docked or a compatible Kodak card reader is 2 Dock the camera, or connect a not connected. compatible Kodak card reader (page 14). If using a card reader, make sure a memory card is inserted. The camera is not properly seated Reseat the camera on the printer on the connector. dock (page 10). The camera or card reader is None required. transferring pictures to the When transfer is complete, press computer, or has established an the blinking Transfer button,. active connection to the computer. A PictBridge compatible device is None required. connected. The Print button is disabled; print command is controlled from the PictBridge compatible device. To print from another source, unplug the PictBridge compatible device.

Picture Size lights Light status One light glows steady green Cause The indicated picture size is available and selected. Action/solution None required. To change picture size, press the Picture Size button repeatedly.

All lights are off

There are no pictures in the camera, To enable the picture size on the card, or on the PictBridge option: compatible device. 1 Take pictures. The camera is not docked, a 2 Dock the camera or compatible Kodak card reader or connect a compatible PictBridge compatible device is not Kodak card reader connected, or a memory card is not (page 14) or PictBridge inserted. compatible device (page 13). If using a card reader, make sure a memory card is inserted. The camera is not properly seated on the connector. Reseat the camera on the printer dock (page 10).
The camera or card reader is None required. transferring pictures to the computer, or has established an active connection to the computer.
Transfer button/light Light status Light glows steady green Light blinks green Cause The printer dock is ready for transferring pictures. Action/solution None required.
Pictures are being transferred None required. to the computer. After transferring pictures, the transfer light continues to blink green until either the Transfer button is pressed again or the connection is no longer available. There are no pictures in the camera or on the memory card. None required. To enable Transfer: 1 Connect printer dock to computer (page 23).

Light is off

The camera is not docked, a compatible Kodak card reader 2 Take pictures. is not connected, or a memory 3 Dock the camera, or connect a card is not inserted. compatible Kodak card reader The printer dock is not (page 14). If using a card reader, connected to the computer. make sure a memory card is inserted. The camera is not properly seated on connector.
Reseat the camera on the printer dock (page 10).
The printer dock is printing in The Transfer button is disabled. standalone mode. The computer is off. Turn on the computer.

Connect a tripod directly to the camera; do not connect a tripod to the camera dock or printer dock. Service agreements are available in some countries. Contact a dealer of Kodak products for more information. The printer dock and the AC power adapter contain a small amount of lead in the circuit board. Disposal of this material may be regulated due to environmental considerations. Disposal of the color cartridge is not regulated and should not be subject to state or local landfill, incineration, or recycling requirements. For more disposal or recycling information, contact your local authorities. In the US, visit the Electronics Industry Alliance Web site at www.eiae.org.

Warranty

Limited Warranty
Kodak warrants Kodak digital cameras and accessories (excluding batteries) to be free from malfunctions and defects in both materials and workmanship for one year from the date of purchase. Retain the original dated sales receipt. Proof of the date of purchase will be required with any request for warranty repair.
Limited warranty coverage
This limited warranty will be honored only within the geographical location that Kodak digital cameras and accessories were purchased. Kodak will REPAIR or REPLACE Kodak digital cameras and accessories if they fail to function properly during the warranty period, subject to any conditions and/or limitations stated herein. Such repair service will include all labor as well as any necessary adjustments and/or replacement parts. Such repair or replacement is the sole remedy under this warranty.
If replacement parts are used in making repairs, these parts may be remanufactured, or may contain remanufactured materials. If it is necessary to replace the entire product, it may be replaced with a remanufactured product.

Limitations

Request for Warranty service will not be accepted without proof of date of purchase, such as a copy of the original dated Kodak digital camera or accessory sales receipt. (Always keep the original for your records.) This warranty does not apply to the battery(s) used in digital cameras or accessories. This warranty does not cover circumstances beyond Kodaks control, nor problems caused by failure to follow the operating instructions in the Kodak digital cameras and accessories Users Guides. This warranty does not apply when failure is due to shipping damage, accident, alteration, modification, unauthorized service, misuse, abuse, use with incompatible accessories or attachments, failure to follow Kodaks operation, maintenance or repacking instructions, failure to use items supplied by Kodak (such as adapters and cables), or claims made after the duration of this warranty. Kodak makes no other express or implied warranty for this product. In the event that the exclusion of any implied warranty is ineffective under the law, the duration of the implied warranty will be one year from the purchase date. The option of replacement is Kodaks only obligation. Kodak will not be responsible for any special, consequential or incidental damages resulting from the sale, purchase, or use of this product, regardless of the cause. Liability for any special, consequential or incidental damages (including but not limited to loss of revenue or profit, downtime costs, loss of the use of the equipment, cost of substitute equipment, facilities or services, or claims of your customers for such damages resulting from the purchase, use or failure of the product), regardless of cause or for breach of any written or implied warranty is expressly disclaimed and excluded herefrom.

A AC power adapter & cord, connecting, 3 accessories & supplies, ordering, 47 B battery charging, 10 charging lights, i, 10, 11, 43 extending life, 9, 11 loading, 8 refreshing Ni-MH battery pack, 11 safety and handling, 50 types, 8 button left/right control, i picture size, i print, i refresh, i transfer, i C cable AC power adapter & cord, 3 USB, 14, 15, 23, 25 camera battery, loading, 8 connector, i docking and charging, 10 preparing for use with printer dock, 8 printing from, 13 56
setting picture quality, 12 tagging pictures for printing, 12 transferring pictures from, 24 Canadian compliance, 55 canceling printing, 19, 29 card reader. See Kodak card reader care & maintenance general, 30 handling, storing cartridge, 3 handling, storing paper, 5 paper feed roller, 31 tips, 51 traveling with printer dock, 32 cartridge. See color cartridge charging camera battery, 10 lights, battery, i, 10, 11, 43 color cartridge door, ii, 4 handling, storing, 3 installing, removing, 4 light, i, 41 color, automatic correction, 28 computer connecting printer dock, 23 installing software, 20 printing from, 26 system requirements, 20 transferring pictures to, 24, 25 uninstalling software, 22
connecting Kodak card reader, 14, 25 PictBridge compatible device, 15 power, 3 connector camera, i power (DC-in), ii, 3 USB (from device), i, 14, 15, 25 USB (to computer), ii, 23 cooling vents, ii copies, selecting number of, 12, 13, 16 customer support, 48 D DC-in, power connector, ii, 3 disposal and recycling of batteries, 50 of printer dock, 51 docking and charging the camera, 10 door cartridge, ii, 4 paper tray, i, 7 E EasyShare software. See Kodak EasyShare software F FCC compliance, 54 firmware, upgrading, 47, 51
H help software, 47 telephone support, 48 troubleshooting, 33 web links, 47 I ImageLink print system, 10 insert, custom camera, 2 installing battery, 8 custom camera insert, 2 paper tray, 7 software, 20 J Japanese compliance, 55 K Kodak card reader printing from, 14 transferring pictures from, 25 Kodak EasyShare software help, 47 installing, 20 printing with, 26 uninstalling, 22 Kodak web sites, 47

T tagging pictures for printing, 12 telephone support, 48 transfer button/light, i, 46 transferring pictures from camera to computer, 24 from Kodak card reader, 25 problems, 40 traveling with printer dock, 32 tray, paper. See paper tray troubleshooting printing problems, 33 status lights, 41 transferring pictures, 40 U uninstalling software, 22 upgrading software & firmware, 47, 51 URLs, Kodak web sites, 47 USB cable, 14, 15, 23, 25 connector (from device), i, 14, 15, 25 connector (to computer), ii, 23 V VCCI compliance, 55 vents, cooling, ii W warranty, 52 Windows OS installing software on, 20 system requirements, 20 uninstalling software, 22 60

Optical Zoom

Megapixels

2.5"

LCD Screen

EasyShareZ712 IS

Zoom Digital Camera
Superior performance. Superb picture quality.
Enter into the world of high zoom and optical image stabilization with the Kodak EasyShare Z712 IS zoom digital camera. This best-in-class* performance camera solves many photographic challenges for aspirational photographers. Its also very affordable, making it a solid alternative to expensive DSLRs. Whether youre high up in the bleachers or in the great outdoors, the Z712 IS puts the entire world within your reach.
Capture sharp, steady shots at long zoom ranges with optical image stabilization Never miss that challenging action shot with best-in-class* click-to-capture speed (0.26 sec.) Capture the details in low light and fast action situations with the high ISO mode Make better, brighter, more vivid pictures right on camera with Kodak Perfect Touch technology Capture natural details, accurate flesh tones, and breathtaking color with the Kodak color science chip Advanced video features include VGA video at 30 fps, image stabilization during zoom, prints from video, and audio capture, playback, on-camera editing Capture stunning shots with ease smart scene mode automatically selects from 10 available scene modes Works with optional Kodak EasyShare printer docks, photo printers, and camera docks
High-ISO mode Capture the details in low light and fast action situations Best-in-class* click-to-capture speed (0.26 sec.) Never miss that challenging action shot Optical image stabilization Capture sharp, steady shots at long zoom ranges
*Among high-zoom, image stabilized digital cameras as of November 2006.
Standard features Sensor type CCD total pixels Effective pixels Lens Lens barrier Zoom Image stabilizer Shutter speed LCD Viewfinder Storage Auto focus Type Focus modes Focus range Auto focus control Auto focus zones Assist light Exposure control ISO sensitivity Metering Compensation Bracketing AE lock Histogram White balance Flash Range 1/2.5" CCD 7.4 MP (3152x2342) 7.1 MP (3081x2313) 36-432 mm (35 mm equiv.) f/2.8-f/4.8 SchneiderKreuznach Variogon lens built-in 12X optical, 4.2X advanced digital zoom, total zoom range 50X optical 1/2-1/1000 sec. in 1/3 step increments 2.5" high resolution (230K pixels) indoor/outdoor color TFT display, 5 level brightness adjustments high resolution (115K pixels) electronic, 100% field of view 32 MB* internal memory, SD/MMC card expansion slot TTL imager AF system normal AF, macro AF, infinity AF, manual Auto: wide 0.5 m(1.6')infinity, tele 1.2 m (3.9')infinity; Macro (wide) 12-60 cm (4.7"-2'), tele 60 cm-1.3 m (2'-4.3') single, continuous TTL multi-zone AF, center zone AF, selectable zone AF (5 zones) yes auto, 80, 100, 200, 400, 800, 1600, 3200** multi-pattern, center-weighted, spot (zone tracks with 5 focus zones) 2.0 EV with 1/3 EV steps 1.0 EV with 1/3 EV steps, 3 images when shutter button is pressed display on live view, quick view, and review auto, daylight, tungsten, fluorescent, open shade Customization Custom settings LCD brightness, capture frame grid, image stabilizer control, quick view, advanced digital zoom setting, orientation sensor, sound, volume, date & time setting, auto power off, video out setting, language, image storage, album

wide: 0.5-4.7 m (1.6'-15.4') (ISO 140); tele: 1.2-2.7 m (3.9'-8.9) (ISO 140) Modes auto, red-eye pre-flash, fill, off -1 to +1 EV in 1/3 steps Compensation Shooting Specifications Drive modes single shot, first burst (2 fps up to 6 frames), last burst (2 fps last 6 frames), self timer (10 sec.), two-shots self-timer (10 sec.), delay shutter (2 sec.), exposure bracketing (3 shots) Shooting modes sport, SCN, high ISO and smart scene via auto, P (program), A (aperture priority), S (shutter priority), M (manual), video Scene modes portrait, night portrait, landscape, night landscape, flower, sunset, backlight, candle light, manner/museum, text, beach, snow, fireworks, children, panorama stitch <0.26 sec. (preview on) wide Click to capture Shot to shot <1.2 sec. Still capture Still format JPEG/EXIF v 2.21 Picture size 7.1 MP (3072x2304), prints up to 76x102 cm (30"x40"); (recorded pixels) 6.3 MP 3:2 (3072x2048), optimized ratio for 10x15 cm (4"x6" prints); 5.0 MP (2592x1944), prints up to 51x76 cm (20"x30"); 3.1 MP (2048x1536), prints up to 20x25 cm (8"x10"); 2.2 MP (1800x1200) 3:2, 2.1 MP (1920x1080) 16:9 1.2 MP email (1280x960), small prints high color, natural color (default), low color, sepia, black Color modes and white Sharpness high, normal (default), low Review menu view by date, view by album, view by image storage, selected, Kodak Perfect Touch technology, crop, protect or unprotect, slide show, copy, multi-up on-camera crop, Kodak Perfect Touch technology Editing Video capture QuickTime video format, MPEG4 Format VGA (640x480) at 30 fps, QVGA (320x240) at Quality 30 fps Length continuous up to 80 min. based on memory capacity Review options view by image storage, selected, protect, album, date; make picture, edit video, protect, action print (4, 9, 16-up), bookmarks, slide show, copy, multi-up Editing make a picture from video (1, 4, 9, 16-up), trim
Sharing Favorites slide show, multi-up, setup menu, direct Favorites Share print, print all, e-mail, Favorites, cancel print Physical specifications I/O interface A/V output (NTSC or PAL, user selectable), exclusive Kodak camera dock, digital (USB 2.0 full speed) connector Power optional Kodak EasyShare docks with Kodak Li-ion rechargeable battery pack; 1 lithium battery CRV3; optional Kodak Li-ion rechargeable digital camera battery KLIC-8000 Dedicated buttons power switch, shutter button, mode dial (high ISO, smart scene, sport, SCN, P, A, S, M, video, Favorite), zoom switch, EVF/LCD, drive, focus, flash, info, review, 5-way switch, Share, menu, delete, jog dial Tripod mount 1/4" standard Dimensions WxHxD: 103.6x74.2x69.7 mm (4.1"x2.9"x2.7") Weight without batteries: 300 g (10.6 oz.) Compatibility Dock compatibility works with optional Kodak EasyShare G600 printer dock, and Kodak EasyShare camera dock series 3 Direct print Kodak EasyShare photo printer 500, ImageLink print system compatible, PictBridge enabled Software works with Kodak EasyShare software SDHC compatible up to 4 GB Service and support Warranty one year Minimum system requirements Windows Windows XP or higher, 600 MHz processor or greater; Internet Explorer 6.0 or higher Macintosh Macintosh OS X 10.3 or higher Minimum hardware requirements 128 MB RAM; 200 MB hard drive disk space available; CD-ROM drive, available USB port; color monitor, 800x600 display resolution, 16-bit minimum Package contents Kodak EasyShare Z712 IS zoom digital camera Kodak lithium digital camera battery CRV3 USB and audio/video cables Lens cap with strap Neck strap Kodak EasyShare software Getting started guide Custom camera insert for optional Kodak EasyShare camera and printer docks Ordering information Kodak EasyShare Z712 IS zoom digital camera.xxx xxxx Recommended accessories Kodak EasyShare G600 printer dock.xxx xxxx Kodak EasyShare photo printer 500.xxx xxxx Kodak color cartridge and photo paper kit.xxx xxxx Kodak EasyShare camera dock series 3.xxx xxxx Kodak EasyShare picture viewer.xxx xxxx Kodak SD high performance memory cards 2 GB.xxx xxxx 1 GB.xxx xxxx Schneider-Kreuznach Xenar 1.4X telephoto lens, 55 mm.xxx xxxx Z712 lens adapter.xxx xxxx Kodak Li-ion rechargeable digital camera battery KLIC-8000.xxx xxxx Kodak Li-ion battery charger K8500.xxx xxxx Kodak digital camera tripod.xxx xxxx B&W circular polarizer.xxx xxxx B&W neutral density filter.xxx xxxx Kodak 8-in-1 card reader.xxx xxxx Kodak 3-in-1 camera case.xxx xxxx

For more information on the Kodak EasyShare Z712 IS zoom digital camera, visit www.kodak.com/go/easyshare
*32 MB internal memory/28 MB available for picture storage (1 MB equals one million bytes). **ISO 3200 available at 1.2 MP setting.
Eastman Kodak Company, 2007. Kodak, EasyShare, Perfect Touch, and ImageLink and the ImageLink print system logo are trademarks of Eastman Kodak Company. Schneider-Kreuznach, Xenar, and Variogon are trademarks of Jos. Schneider Optische Werke GmbH used under license by Eastman Kodak Company. Product specifications subject to change without prior notice. Simulated screen images. IC-xxxx CAT No. xxx xxxx