Quick Guide The Konftel 200W conference phone

English

Conference phones for every situation

Description Konftel 200W

Konftel 200W is a DECT conference phone with a pickup range up to 30 m2. The Konftel 200W connects to different makes of GAP-compatible DECT systems. If your office does not have a compatible DECT system, Konftel can supply a DECT base station for analogue connection.
Speaker LEDs Microphone Receiver remote control

Display Keypad

Power supply Tape recorder socket Sockets for expansion microphones Cable duct

Holes for wall bracket

Connecting and installing
Plug the Konftel 200W in the mains using the power adapter as illustrated. Place the conference phone in the middle of the table.
Answering and making calls

Answering calls

A ring tone will be heard and the blue LEDs start flashing.

Press OK to answer.

The display shows the duration of the call.

Making calls 0-9. 0-9.

123456
Press OK. Dial the number.
Dial the number. Press OK.
The number is called within 3 seconds.

Redialling

You can easily redial the number you last called. 123456

REDIAL

Press the up arrow. Press OK.
The last number that you dialled appears in the display. The number is called within 3 seconds.

Speed dialling

Please refer to the manual for instructions on adding and updating numbers in the phonebook.
Press the Up/down keys repeatedly.

PETER G.

PHONEBOOK
The pre-programmed names in the phonebook appear in alphabetical order. The last dialled number appears first. The number is called within 3 seconds.
Press OK to call the selected name/number.

during a call

Adjusting the speaker volume
Increase the speaker volume using + and lower it using -.

Mute function

Press the mute key to turn the microphone off.
The LEDs change from blue to red. The other party cannot hear what you are saying.
Press the mute key again to turn the microphone back on.
Adjusting the sound manually
Konftel 200W adjusts itself automatically when you switch it on to eliminate echo. It also senses changes in the room and continually adapts during the call. If, despite this, you still experience reduced sound quality, Konftel 200W can be adjusted manually at any time.

Press c.

Ending calls

A short noise is heard.

End the call by pressing OK.
Registering in a DECT base station
You need to register your Konftel 200W in a DECT base station before it can be used. Here we explain how to register in a Konftel DECT base station. To register your Konftel 200W in other makes of base station, simply follow the same procedure. Please refer to your base station instruction manual or contact your companys switchboard administrator if you are unsure.
Set Konftel DECT base station in registration mode
Press and hold the key/LED on the base station until it starts
to flash. The base station is now in registration mode. Once registration has been completed, the LED will stop flashing. If the base station does not identify a DECT phone within 2 minutes, the registration mode will switch off automatically.

Key/LED

Register Konftel 200W in a DECT base station
Press the MENU key. Select the menu tool using the Up/down key. Press OK. Select the menu Reg using the Up/down key. Press OK. Select a base (14).
If no base station has been programmed, choose no. 1. Numbers that are ticked are being used.

Base 1

DECT system:
Press OK. Select a DECT system. Press OK. Enter the security code (PIN code) (standard code is 0000). Press OK.

Some DECT systems (not Konftel DECT Base Station) require a PARK code. Check with your companys switchboard supplier.
Enter the PARK code if this is required. Otherwise, leave blank. Press OK.
Your Konftel 200W is now in registration mode and is searching for a base station in registration mode. Wait until you receive confirmation that registration has been completed. Registration can be interrupted by pressing C. If registration was successful, the word Done will appear in the display.

Search

Press OK.
The Konftel 200W is now ready to use.
Konftel is a leading company within loudspeaker communication and audio technology. We develop and sell products and technology for telephone conferences based on cutting-edge expertise within acoustics and digital signal processing. Characteristic of our products is that all conference telephones contain the same high quality audio technology OmniSound providing crystal clear sound. Read more about Konftel and our products on www.konftel.com.
Developed by Konftel AB Box 268, SE-Ume, Sweden Phone: +Fax: +E-mail: info@konftel.com Web: www.konftel.com

3134-61-001 Rev B UKE

User guide The Konftel 200W conference phone

English

Conference phones for every situation
This product is equipped with OmniSound, the crystal clear sound.
DECT conforms to the GAP standard
DECT Digital Enhanced Cordless Telephone. DECT incorporates encryption for maximum call security. GAP (Global Access Profile) ensures the interoperability of DECT equipment of different manufacturers.
Konftel AB hereby declares that this conference unit complies with all essential requirements and other relevant provisions of Directive 1999/5/EC.
WARNING: To reduce the risk of fire or shock hazard, do not expose this product to rain or moisture.

CAUTION

RISK OF ELECTRIC SHOCK DO NOT OPEN
The lightning symbol is intended to alert you to the presence of uninsulated dangerous voltage within this products enclosure that might be of sufficient magnitude to constitute a risk of electric shock. Do not open the products case. The exclamation symbol is intended to inform you that important operating and maintenance instructions are included in the literature accompanying this product.

CAUTION:

TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT REMOVE COVER OR BACK. NO USERSERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL.

Table of contents

Description 2
General...2. Maintenance..2 Connecting and installing..3 Display and keypad...4 Konftel DECT base station (accessories)..5 Registering Konftel 200W with a base station..6
Answering calls...8 Making calls...8. During a call..9 Ending calls...9

Advanced features

Making multi-party calls..10 Updating the phonebook.. 11

Settings

Adjusting ring volume...14. Adjusting date and time..14 Changing languages..15 Adjusting key tone..15 Selecting a DECT base station..16 Showing status.. 17 Deregistering a phone.. 17 Registering a new base station..18 Searching for a DECT handset..18 Adjusting R key function (flash duration).19.

Accessories

Expansion microphones..20. Remote control..22. Item numbers for accessories and spare parts.23
Troubleshooting Technical data
Konftel 200W conference phone.25 Konftel DECT base station (accessories).26 Expansion microphones (accessories)..27. Remote control (accessories)..27

Service and guarantee

Description

General

The Konftel 200W is a DECT conference phone with an omnidirectional, highlysensitive microphone which, together with Konftels OmniSound and the built-in speakers, provide optimal sound quality and maximum reduction of room echo, even when the person speaking is standing at a slight distance from the conference unit. The pickup range is up to 30 m2. Expansion microphones can be connected to the Konftel 200W to provide increased range and optimal sound conditions in larger meeting rooms. By turning up the loudspeaker volume level, the pickup range increases from 30 m2 to 70 m2. The optional remote control adds further ease to meetings, allowing you to control all the Konftel 200W functions such as the speed dialling keys for the most frequently used phone numbers. The Konftel 200W connects to different makes of GAP-compatible DECT systems. You can find out which DECT systems have been tested with the Konftel 200W on our website, www.konftel.com. If your office does not have a compatible DECT system, Konftel can supply a DECT base station for analogue connection. Please note that you need to connect (register) your Konftel 200W to a DECT base station before it can be used. There is a description of the Konftel DECT base station in the User guide, along with instructions on how to connect (register) the conference phone to an DECT base station. Check that all parts are included in the package. If any parts are missing, please contact your retailer.

The Konftel 200W conference phone Power adapter with 6-metre cable Quick reference guides in different languages CD with user guides in different languages

Maintenance

Clean the equipment with a soft, dry cloth. Never use liquids.
Speaker LEDs Microphone Receiver remote control

Display Keypad

Power supply Tape recorder socket Sockets for expansion microphones Cable duct

Holes for wall bracket

Connecting and installing
Plug the Konftel 200W in the mains using the power adapter as illustrated. Place the conference phone in the middle of the table.

Display and keypad

Date Signal strength

Time / Call duration

OK / answer/end Menu / back R key (see pages 10 and 19)
Up/down Mute / pause (see page 9) Delete / adjust the sound (see page 9)
Characters for text input

See page 11.

(blank). - , 1 A B C 2 a b c 2 D E F 3 d e f 3 G H I 4 g h i 4 J K L 5 j k l 5 M N O 6 m n o Shift (large / small letters) P Q R S 7 p q r s 7 T U V 8 t u v 8 W X Y Z 9 w x y z 9
Konftel DECT base station (accessories)
Holes for wall suspension

Key and LED

Power supply

Line connection

Connection
Connect the base station to a telephone jack and the mains using the power adapter as illustrated.

Wall suspension

The base station can be mounted on the wall. Use the screws provided as illustrated. Make sure it is securely mounted.

Registration

Registering Konftel 200W with a base station
The Konftel 200W has to be registered with a base station before it can be used. Note that both the base station and the Konftel 200W have to be put into registration mode. These are the instructions for registering with a Konftel DECT base station. If registering Konftel 200W with other makes of base station, follow the same procedure. Please refer to your base station user guide if you are unsure.
Set the Konftel DECT base station in registration mode
Press and hold the key/LED on the base station for
at least 2 seconds until it starts to flash. The base station is now in registration mode. Once registration has been completed, the LED will stop flashing. If the base station does not identify a DECT phone within 2 minutes, the registration mode will switch off automatically.

Key/LED

Set the Konftel 200W in registration mode
Press the MENU key. Select the menu Tools using the Up/down key. Press OK. Select the menu Reg using the Up/down key. Press OK. Select a base (1-4).
If no base station has been programmed, choose no. 1. Numbers that are ticked are being used.

Base 1

DECT system:
Press OK. Select a DECT system. Press OK.
Enter the security code (PIN code) (standard code is

0000).

Press OK.
Some DECT systems (not Konftel DECT Base Station) require a PARK code. Check with your companys switchboard supplier.
Enter the PARK code if this is required. Otherwise,

leave blank.

Search
Your Konftel 200W is now in registration mode and is searching for a base station in registration mode. Wait until you receive confirmation that registration has been completed. (The base station has to be in registration mode.) Registration can be interrupted by pressing C.
If registration was successful, the word Done will appear in the display.
The Konftel 200W is now ready to use. Please see page 14 for other menu options and settings.
If registration was not successful
If registration was not successful, the word Fail will appear in the display. Possible reasons for this: Incorrect security code (check with your companys switchboard administrator) Incorrect or missing PARK code (check with your companys switchboard administrator) No base station within range or not activated in registration mode

Answering calls

A ring tone will be heard and the blue LEDs start flashing.

Press OK to answer.

The display shows the duration of the call.

Making calls

123456

0-9. 0-9.

Press OK. Dial the number.
Dial the number. Press OK.
The number is called within 3 seconds.

Redialling

You can easily redial the number you last called.

REDIAL

Press the up arrow. Press OK.
The last dialled number appears in the display. The number is called within 3 seconds.

Speed dialling

Press the Up/down keys repeatedly.

PETER G.

PHONEBOOK
The pre-programmed names in the phonebook appear in alphabetical order. The last dialled number appears first. The number is called within 3 seconds.
Press OK to call the selected name/number.

During a call

Adjusting the speaker volume
Increase the speaker volume using + and lower it

using -.

Mute function
Press the mute key to turn the microphone off.
The LEDs change from blue to red. The other party cannot hear what you are saying. back on.
Press the mute key again to turn the microphone
Adjusting the sound manually
Konftel 200W adjusts itself automatically when you switch it on to eliminate echo. It also senses changes in the room and continually adapts during the call. If, despite this, you still experience reduced sound quality, Konftel 200W can be adjusted manually at any time.

Press c.

A short noise is heard.

Ending calls

End the call by pressing OK.

Making multi-party calls

Konftel 200W supports the switchboards multi-party call feature. Please note that the number of people who can be connected to a call may be limited by the service provider and the PBX to which Konftel 200W is connected. Most service providers offer a phone meeting service to make it easy to create multi-party calls. This could be a smart option for linking up several participants.
Call the first participant (dial the number and press
OK). When the call has been connected:

Press the R key.

A second dialling tone is heard. answer.
Dial the second participants number and wait for an Press the R key and then 3.
All three participants are now linked together in one call.
What if no one answers when you dial the second number
Go back to the first call by pressing R then 1.
If you experience problems making multi-party calls
There may be several reasons for this. The R key sends instructions to the base station, which then sends a pulse to the telephone line. The duration of the pulse varies depending on the country and switchboard. Read Adjusting R key function on page 19. Your switchboard may not be programmed to admit multi-party calls. Contact your companys switchboard administrator to initiate this service. Your switchboard may require a different command to R3 to link up all call participants. Please consult Konftels website under FAQ for other commands.

Updating the phonebook

The Konftel 200W has a phonebook that holds up to 50 entries. This makes it easy to call frequently used numbers. See page 8 for making calls using the speed dial list.
General information about entering text using the keypad
Enter a name in the address book using the keypad. Each key covers a number of letters and other characters - far more than shown on the key (see page 4). Press the same key repeatedly to change to another character. If there are two letters under the same key that you want to enter one after the other, you need to pause slightly before entering the second letter. Press the shift key to switch to lower-case (small letters). Press C to delete the last character. You can cancel an entry at any time by pressing MENU. The mute key inserts a slight pause in speed dial numbers. You might find this useful if you are calling via a switchboard and have to dial a nought in order to get a dialling tone. A pause might be necessary in some cases to give the dialling tone time to be activated.

Adding new numbers

Press the MENU key. Press OK.

Add entry

NUMBER:
The phonebook is the first option on the menu. Add entry is displayed. The last dialled number is automatically displayed. last dialled number).
Enter the number you require (unless you want the Press OK. Enter a name using the keypad. Press a key repeatedly to change to another character.

A b c.

Press OK to save the number.
The word Done is displayed. If the phonebook already has 50 entries, the words Memory full will be displayed.

Press the MENU key.

The phonebook is the first option on the menu.

PETER.

Press OK. Press the Up key so that Edit is displayed. Press OK. Press Up/down to look through the phonebook until
you find the name or number you want to update.
Press OK. Change the number if that needs updating. Delete

digits using C.

Press OK. Change the name if that needs updating. Delete Press OK to save your changes.
letters using C and enter new letters as per instructions on page 11. The word Done is displayed.

Delete names and numbers

Press OK. Press Up/down until Erase is displayed. Press OK.
Press Up/down to look through the phonebook until
you find the name or number you want to delete. Erase? is displayed. The word Done is displayed.

Erase?

Press OK to confirm deletion.
(Press MENU to cancel without deleting the number.)
Adjusting ring volume Press the MENU key. Select Ring tone using the Up/down key. Press OK. Select the desired volume of the ring tone using the
Up/down key. The selected volume is displayed. The ring tone can be turned off by selecting the symbol that shows a crossed-out bell. The selected setting is saved.
Adjusting date and time Press the MENU key. Select Date and time using the Up/down key. Press OK.
The current date and time appear in the top of the display. A two-way arrow appears under the date. with OK. The two-way arrow then moves to the month. Change the year and confirm with OK. Change the hour and confirm with OK. Change the minutes and confirm with OK. The selected setting is saved.
Change the date using the Up/down key and confirm Change the month and confirm with OK.
Changing languages Press the MENU key. Select Language using the Up/down key. Press OK. Select the language you require using Up/down. English Press OK.
The selected setting is saved.

Adjusting key tone

You can select whether or not you want a tone to be heard when you press a key. Note that this setting does not affect the key tone you hear when you dial a number.

Keypad tone

Press the MENU key. Select Tools using the Up/down key. Press OK. Press OK again to confirm Keypad tone which is the
first option on the menu.

Off Done

Select On or Off using Up/down. Press OK.
Selecting a DECT base station
Use this option to choose one of the registered base stations. You can also let Konftel 200W automatically select the base station with the strongest signal. See page 6 for instructions on how to register with a new base station.
Press the MENU key. Select Tools using the Up/down key. Press OK. Select the menu Base using the Up/downkey. Press OK.
The current base station (e.g. Base 1) is shown in the display. option Auto using the Up/down key.
Look through the registered base stations and the
Auto will automatically select the base station with the strongest signal. The chosen option is marked with a tick.
The conference unit will now search for the selected base station. Wait for confirmation. If the base station is found, the word Done will appear in the display. If the base station is not found, the word Fail will appear instead. Select another base station if that is the case, or check that the base station you wanted actually is connected and within range.

Showing status

Use this option to check the ID number of either the conference unit or base station. This information can be useful in an installation with many units.

Status

Press the MENU key. Select Tools using the Up/down key. Press OK. Select the menu Status using the Up/downkey. Press OK. Press the Up/down key.
PARK 0412151105 IPEI: 0412150005
The ID number (RFPI, PARK) of the current base station appears in the display. The ID number (IPEI, HS no.) of the conference phone appears in the display.
Press OK to return to the menu.

Deregistering a phone

This only applies to a Konftel DECT base station. Seven telephones (handsets or Konftel 200W) can be registered with a Konftel DECT base station. Use this option to deregister (remove) a telephone from the base station. Note! You cannot deregister the unit that you are using for deregistering, i.e. Konftel 200W cannot deregister itself.

Handset 2

Press the MENU key. Select Tools using the Up/down key. Press OK. Select the menu Dereg using the Up/downkey. Press OK. Select the handset you want to deregister using the

Up/down key. (The unit you are using is marked with a tick.)
Press OK. Enter the base stations security code (PIN code)

(standard code is 0000).

Wait until you receive confirmation that deregistration has been completed. If the base station is found, the word Done will appear in the display. If the base station is not found, the word Fail will appear instead.
Registering a new base station

See page 6.

Searching for a DECT handset
This only applies to a Konftel DECT base station. You can let a Konftel DECT base station search for telephones (handsets or Konftel 200W) that are registered with the base station. A handset normally emits a tone while being searched for by the base station. The Konftel 200W emits an audible tone when it is being searched for by the base station and the word PAGE appears in the display. Press any key on the Konftel 200W to escape from this mode.
Briefly press the key/LED on the base station. Localising the telephones. Press one more time to escape search mode.
The base station is now in search mode and the blue LED flashes slowly.
Adjusting R key function (flash duration)
This only applies to a Konftel DECT base station. The R-function (one of its functions is to create multi-party calls) is based on the phone sending a special R-pulse (flash). The various phone systems and PBXs of other countries require different durations for activating the R-pulse. With the Konftel 200W, the R-pulse duration can be adjusted accordingly. R1 = 65 ms R2 = 100 ms R3 = 150 ms R4 = 270 ms R5 = 600 ms R6 = 80 ms

R function R2

Press the MENU key. Select Tools using the Up/down key. Press OK. Select the menu R function using the Up/down key. Press OK.
The current R-pulse setting appears in the display.
Select the setting you require using Up/down key. Press OK.

Expansion microphones

Expansion microphones Item no. 900102074 0.82.5m

Konftel 200W

Installation
The expansion microphones should be positioned as illustrated to achieve the best possible sound quality.

accessories

Connecting and programming
Two expansion microphones can easily be added onto the Konftel 200W to increase the pickup range up to 70 m2. The expansion microphones are supplied with two different cable sets, 1.5 and 2.5 m.
Unplug the power cable from the conference unit. Place the expansion microphones at least 0.8 m and
no more than 2.5 m from the Konftel 200W and connect them using the cables provided.
Plug the power cable in again.
The microphone in the Konftel 200W is now deactivated. The display indicates that the expansion microphones are activated. Always unplug the power cable before removing the microphones.

Press the up or down key on one of the expansion
microphones to adjust the speaker volume.

Manual adjustment

Press the up and down keys at the same time for
manual adjustment (see page 9). A short noise is heard.
Press the mute key on one of the expansion microphones to switch off the microphones. The LEDs change from blue to red. The other party cannot hear what you are saying. back on again.
Press the mute key again to switch the microphones

Remote control

Konftel 200W has an optional remote control. This allows you to control all the functions from wherever you are in the room.
Lifts the handset or hangs up, whether Konftel 200W is in a menu mode or not. If the phonebook is displayed, the number will be dialled. Adjusts Konftel 200W to the acoustics of the room. Keypad for dialling numbers or entering names in the address book. (See pages 4 and 11.) Opens or closes menu mode. Adjusts the volume, goes through the phonebook and the menus. OK in menus. This works in the same way as the handset key when a menu is not active. Deletes characters when dialling numbers or entering names. Exits menus without saving changes. Mute function. Turns the microphones on and off. Inserts pause in speed dial numbers (see page 11). Calls last dialled number irrespective of menu mode. R-function. Used for some operator services (e.g. multi-party calls, see page 10). Speed dialling keys. When a speed dial number is saved or updated in the phonebook, it can be stored by finishing off the programming with a function key instead of OK. Then when the key is pressed, the stored number is dialled. Note that by storing a new number on a key that already has a speed dial number, you will delete the first number.

Item no. 900102038

Item numbers for accessories and spare parts
Item no. 9146030 Designation Ceiling mount suspension Remote control Anti-theft device, max. length 3 m Konftel DECT base station Expansion microphones (1 pair) Extension cord electrical, 10 m Extension cord telephone, 10 m Tape recorder cable Wall mounting bracket

Troubleshooting

If your Konftel 200W is not working: 1. Check that the microphone is turned on during the call. The blue microphone LEDs should be lit. 2. Check that the Konftel 200W is within range for a DECT base station and that it is registered with the base station. Read more on page 7. 3. Bypass any extension cables and see if the Konftel 200W works properly. If not, contact your retailer. 4. Disconnect the expansion microphones and see if the Konftel 200W works without them. If not, contact your retailer. 5. If the Konftel 200W needs to wait for a second dialling tone, you should enter a pause using the pause/mute key when entering a telephone number as an instruction or in the phonebook.

Technical data

Konftel 200W conference phone
Power supply: Speaker volume: Room echo reduction: Line echo reduction: Environment: Transformer 12V DC/230V AC, 700mA (Europe) Transformer 12V DC/120V AC, 700mA (USA) Adjusts to 15 levels 208 ms 38 ms Pickup range <30 m2 Reverberation time in room <500 ms Background noise <45 dBA Temperature range: 540 C Diameter 232 mm 700 grams

Dimensions: Weight:

Approvals
Electrical safety: EMC: DECT/radio: GAP standard: EN60950:2001 EN301489-01/06:2000 European DECT standard: EN301406-V1.4.(DECT frequency: 1880-1900 MHz, average power is 10 mW per channel DECT output power: 250 mW peak power in one of 24 time slots, ~10mW/channel DECT range: Unobstructed range, up to 300 metres. Indoor range, up to 50 metres). TBR22
The unit can generate a tone when used in environments where there is strong radio interference or high-frequency interference in the power supply cable and will then resume normal function once the interference has stopped.
Power supply: Cable length: Tele connection: Compatibility: Transformer 230 V AC/6 V DC, 300 mA 2 metres Analogue PBX or PSTN, RJ-11 A Konftel DECT base station is GAP-compatible and can be connected to analogue lines or any PBX equipped with an analogue extension. Up to 7 GAP-compatible DECT units can be connected to a Konftel DECT base station 175x160 mm 240 grams
Electrical safety: EMC: DECT/radio: GAP standard: Tele: EN60950:2001 EN301489-01/06:2000 European DECT standard: EN301406-V1.4.(DECT frequency: 18801900 MHz, average power is 10 mW per channel DECT output power: 250 mW peak power in one of 24 time slots, ~10 mW/channel DECT range: Unobstructed range, up to 300 metres. Indoor range, up to 50 metres). TBR22 TBR21:1998
Expansion microphones (accessories)
Power supply: Cabling: Environment: Dimensions: Power from microphone output Modular 4/4-contacts, 2x1.5 m and 2x2.5 m Temperature range: 540 C Diameter 105 mm, height 30 mm
Remote control (accessories)
Batteries: Environment: Range: Dimensions: Weight: Keyboard: 4 x R03, 1.5V Temperature range: 540C Up to 5 metres 205x55x21mm (LxBxH) 140 grams 26 keys
Contact a Konftel retailer first if your conference telephone needs servicing. See the American User Guide for guarantee terms and information on American FCC and Canadian FCC and IC norms (in English only). Contact Konftel support for more information.

Konftel support

+46(0)90-(MondayFriday 08.0017.00) E-mail: info@konftel.com USA and Canada: +1 866-606-4728 (MondayFriday 08.0017.00) E-mail: konftel.usa@konftel.com

Konftel is a leading company within loudspeaker communication and audio technology. We develop and sell products and technology for telephone conferences based on cutting-edge expertise within acoustics and digital signal processing. Characteristic of our products is that all conference telephones contain the same high quality audio technology OmniSound providing crystal clear sound. Read more about Konftel and our products on www.konftel.com.
Developed by Konftel AB Box 268, SE-Ume, Sweden Phone: +Fax: +E-mail: info@konftel.com Web: www.konftel.com

3132-61-001 rev B UKE