Overview of the Users Manual

Digital Technology

Help Mode Control Panel with Interactive Touch Screen Key Operator Functions Machine Labels
Features of the Konica 7045 Printer/Copier Standard Equipment Configuration Options Optional Equipment

Introduction 1-1

Introduction
Welcome to the Konica 7045 Workgroup Document SystemTM. This section includes an overview of the User's Manual and a description of the product. Before attempting to operate your equipment, read this section to familiarize yourself with the product and also read Safety Information in section 2 to learn how to operate this equipment in a safe manner.
Overview of the User's Manual
To enjoy optimal performance, operate your equipment as instructed in this User's Manual. As a convenience to all users, keep the manual located with the equipment. Manual Organization This manual includes twelve topic sections, Specifications of the product, a Glossary of copier terms, and an Index. Highlights are as follows: Section 1: General product information and features. Section 2: Safety information to be read and understood before operating this equipment. Section 3: Machine information to be used as a reference when performing all jobs, especially when capacities, sizes and weights are factors. Section 4: Paper information to be used as reference when performing all jobs. Section 5: Copier management information to be read before operating this equipment. Section 6: Information on using the touch screen and selecting basic functions. Section 7: Information on machine output modes with and without the finisher. Section 8: Information on special application modes. Section 9: Information on Job Memory functions. Section 10: Provides Shortcuts for special application functions and some basic functions. Section 11: Information on Key Operator functions to be used only by an authorized person. Section 12: Information on machine maintenance and replenishing paper and toner. Section 13: Troubleshooting information for clearing mishandled paper. Section 14: Provides machine specifications for the main body and accessories. Page Design The page layout of this manual is designed to help you perform each operation quickly and easily. The basic format includes an introductory explanation of each function; stepby-step procedures; and illustrations to enhance many of the procedures. Caution statements specific to a topic are located on appropriate pages. Special notes are located at the bottom of the page.

1-2 Introduction

The Konica 7045 Workgroup Document System is a digital printer/copier that can be used either as a standalone copier or as a high-speed network printer when connected to the optional IP-431 Image Processor. The Konica 7045 Printer/Copier can also be used as a print server on a network operating system when installed with the optional KN-303 Network Interface Board. Separate users manuals and installation instructions are included with the optional IP431 and KN-303 devices. Digital technology and memory capability of the Konica 7045 Printer/Copier provide many advantages over the conventional photocopying process. In conventional photocopying, a scanned image virtually remains intact as it is represented on the drum and copied onto the output media. While many settings can be made before outputting the copies, such as with image reduction, enlargement, and erasure or job store and job recall, the conventional photocopying process is not capable of transforming image into bits and storing image data into memory as with digital technology. In the Konica 7045 Printer/Copier, scanned image is electronically digitized into data bits that are represented in code form and stored into memory. Stored data can be retrieved from memory and output in various ways, as controlled by software. Digitized image is represented as pixels on a screen and as dots per inch (dpi) on hard copy. The Konica 7045 Printer/Copier resolves image at 600 dpi. Konica 7045 Printer/Copier digital technology enables you to: feed originals only once to make multiple copies, thereby preserving the condition of originals store image in memory and perform Sheet/Cover insertion, Chapter, Combination, Booklet, Image insert, Book copy, Mixed original, Repeat, Image shift enhance photo, complex text image quality, and enhance lighter image reduce toner consumption and produce clean copies with Non-image area erase organize images into booklet format insert images scanned from the platen into a set scanned from the document feeder overlay stamp images on scanned original check copying conditions and produce a proof copy before making multiple copied sets confirm the current machine status select offset-sort, offset-group, or staple-sort output mode using optional Finisher (FS109) set reverse jobs to make copies of different types in succession

ADF MODE 1-1, 1-2 Original size: 11"x17", 8.5"x14", 8.5"x11", 8.5"x11"R, 5.5"x8.5", 5.5"x8.5"R, A4 Max. feeder capacity: 50 original sheets RADF MODE 2-2, 2-1 Original size: 11"x17", 8.5"x14", 8.5"x11", 8.5"x11"R, 5.5"x8.5", 5.5"x8.5"R, A4 Max. feeder capacity: 50 original sheets MIXED SIZE ORIGINAL MODE Original size: 11"x17", 8.5"x14", 8.5"x11", 8.5"x11"R, 5.5"x8.5", 5.5"x8.5"R mixed. Mixed feeder capacity: 50 original sheets Unsuitable RADF Originals
Curled, creased or folded originals

Paste-ups or cut-outs

Glossy or transparent (OHP) film, art paper, cellophane
Folded, punched or stapled originals

Thin or thick originals

NOTE: Use only paper recommended by Konica Business Technologies, Inc.

Paper Information 4-3

Using the Reversing Automatic Document Feeder (RADF) (continued)

Positioning Originals

The document feeder (RADF) automatically feeds up to 50 originals directly to the platen glass, starting with the top sheet. The RADF should only be used for unstapled, unfolded, smooth, flat originals.
Original size detection requires accurate paper guide adjustment APS detects size 11"x17", 8.5"x14", 8.5"x11", 8.5"x11"R, 5.5"x8.5", 5.5"x8.5"R, and A4 Size, weight and capacity are specified for all copy modes on p. 4-3
Before placing originals in the tray, be sure the document feeder is closed fully. 1 Position original(s) FACE UP on the document feeder tray. Place two-sided originals with page one FACE UP. 2 Adjust paper guides.

4-4 Paper Information

Positioning Mixed Originals
Mixed size originals can be copied together from the document feeder in either APS mode or AMS mode. In APS mode, copies will be output on mixed paper sizes to match the originals. In AMS mode, copies will be output on one common paper size that you select in which case an appropriate AMS magnification ratio will be selected automatically. To use the mixed original mode, see procedure on p. 8-23 to p. 8-24.
Mixed original size: 11"x17", 8.5"x14", 8.5"x11" and 5.5"x8.5" mixed (16 lb~32 lb) 8.5"x14", 8.5"x11"R, 8.5"x11" and 5.5"x8.5" mixed (16 lb~32 lb) 5.5"x8.5"R original is available in horizontal direction only. RADF capacity: Max. 50 sheets Print quantity: Max. 999 sheets Incompatible: Rotation exit, Staple-sort, V/H zoom, Sheet/Cover Insertion, Combination, Booklet, Transparency Interleaving and Thin/Thick Paper modes in Special Paper, Image Insert, Book Copy, Repeat, AUTO Layout, Image Shift, Non-Image Area Erase, STAMP/ OVERLAY

Basic Operations 6-3

Copy Mode Specifications Incompatible functions 1-1: Chapter; Booklet 1-2: Transparency Interleave 2-1: Chapter; Booklet; Book Copy; Repeat; AUTO Layout; Non-Image Area Erase 2-2: Transparency Interleave; Repeat; Book Copy; AUTO Layout; Non-Image Area Erase RADF capacity 1-1, 1-2, 2-2, 2-1: 50 sheets (copying can be resumed after removing paper from bins) RADF original size requirements 1-1, 1-2, 2-2, 2-1: 11"x17", 8.5"x14", 8.5"x11", 8.5"x11"R, 5.5"x8.5", 5.5"x8.5"R, A4 (8.27"x11.69", 210mmx297mm)

2-2 Copying

Double-sided original

7045 7045

Duplex copy

Single-sided originals

1-2 Copying

2-1 Copying

Simplex copy

6-4 Basic Operations

Copy Mode (continued)

Copy Mode Using RADF

Before selecting the Copy Mode shown on the screen below, read specifications on the previous page and see Section 4 for information on original/copy paper and positioning originals.
Basic Screen (with 1-1 mode selected)
1 Touch the desired MODE key: zsz, zsx, xsz, or xsx. A copy mode key will appear dimmed if it is incompatible with other selections made. 2 Position original(s) FACE UP in the document feeder. 3 When all settings are acceptable, press [START]. To cancel the mode, touch the desired MODE key on the Basic Screen.
NOTE: When the finisher capacity is exceeded due to the print quantity selected, remove the copied sets while the paper is exiting; otherwise, mishandled paper will occur.

Basic Operations 6-5

1-2 Copy Mode Using Platen Glass
When copying in 1-2 mode from the platen glass, use the Platen store mode. Refer to p. 4-2 for details on positioning originals.
Incompatible Basic Copying Conditions: Using RADF Incompatible Applications: Transparency Interleave, Image Insert
Basic Screen (with 1-2 mode selected)
1 Open the document feeder. The RADF indication on the Basic Screen will disappear and the xsz and xsx keys will be dimmed to show inactivity. 2 Position original FACE DOWN on the platen glass, then close the document feeder.
IMPORTANT: PLACE AND SCAN ORIGINALS IN REGULAR ORDER OF PAGINATION.
3 Touch zsx, then make the desired copying selections. Some function keys will appear dimmed if they are incompatible with other selections made. 4 Enter the desired print quantity from the control panel keypad. 5 Touch SCAN on the Basic Screen. The original image will be stored into memory. 6 Repeat steps 1, 2, and 5 until all originals are scanned. To delete the scanned data without printing, press [STOP/CLEAR]. 7 Press [START] to print.

NOTE: When the message Please load size ** paper in any tray except tray # is displayed, load the specified paper into the tray.
5 When the scanning for the reserve job is completed, the Basic Screen for the current printing job will be restored. 6 Repeat step 2 to 4 to reserve more than one job. 7 Copying on the reserve job will start automatically after completing the current job.

6-18 Basic Operations

Mishandled Paper During Reserve Setting
If a misfeed occurs with the job in progress while you are setting a reserve job, the SETTING indicator on the screen will change to JAM.
If originals in the reserve job are already scanned when the misfeed occurs, the reserve job will be performed after the jam is cleared and the cleared job is completed. 5 Touch JAM to display the Jam Position Screen. To view Help Screen instructions, touch GUIDE and remove paper/original. The JAM will change to SETTING when cleared job is completed. Press [START]. The output job will be reprocessed. Touch RESERVE to continue setting the reserve job.
If scanning is not completed when the misfeed occurs, but reserve settings were already made, the reserve job can be performed after the cleared job is completed. Simply insert the original document and press [START].

Basic Operations 6-19

When Paper is Depleted for the Job in Progress
If the paper supply for a print job in progress becomes depleted while you are setting a reserve job, the SETTING indicator on the screen will change to ADD PAPER (blinking). In this case, you can still continue the reserve job setting.
1 Touch ADD PAPER to display the Basic Screen for the print job. 2 Confirm the empty tray and add paper. 3 Press [START]. The ADD PAPER will change to SETTING and the print job will be reprocessed. 4 Touch RESERVE to continue setting the reserve job.

6-20 Basic Operations

Job List Screen
Touch the JOB LIST key on the Basic Screen to display the Job List Screen (see below). The Job List Screen allows you to perform the following functions. Confirm machine status Change order of reserve job Delete reserve job To return to the Basic Screen, touch OK on the Job List Screen.
Basic Screen Job List Screen
To change the order of reserve job 1 Touch the lower/upper arrow key to highlight the desired reserve job. 2 Touch ADVANCE. The highlighted reserve job is advanced by one in printing order unless the job preceding the selected one is already in progress. 3 To return to the Basic Screen, touch OK on the Job List Screen. To delete reserve job 1 Touch the lower/upper arrow key to highlight the desired reserve job. 2 Touch DELETE. The Job Clear Confirmation Screen will be displayed. 3 Touch YES. The highlighted reserve job is cleared. 3 To return to the Basic Screen, touch OK on the Job List Screen.

The Interrupt mode cannot be selected with the following copier conditions: The Basic Screen is not displayed. The Call for Sevice message displayes or a paper misfeed occurs.

Incompatible: Reserve

Control Panel

DATA RINT COPY

STOP / CLEA
1 To stop the current copying job, press [INTERRUPT]. For particular jobs in progress, copying will cease only after certain phases of the immediate operation are completed, as indicated by LED conditions described below. Collectively printing image stored in memory The [INTERRUPT] LED blinks until one set of the current job is printed. Then the LED remains steady for the temporary job performed in Interrupt mode. Scanning originals into memory The [INTERRUPT] LED blinks until scanning is completed for all originals placed in the document feeder. Then, the LED remains steady for the temporary job performed in Interrupt mode. Scanning originals into memory while printing in Reserve mode (see note 1) The [INTERRUPT] LED blinks until the copier completes the current printing job, scans all originals placed in the document feeder, and prints one set of the reserve job. The LED remains steady for the temporary job performed in Interrupt mode. 2 The SETTING indicator on the Basic Screen will change to INTERRUPT.

Basic Operations 6-31

Interrupt Mode (continued)
3 Remove any document from the platen glass or from the document feeder, if present. 4 Place new original(s) FACE DOWN on the platen glass or FACE UP in the document feeder. 5 The copying settings in Interrupt mode are as follows. Copy Mode : 1-1 RADF : ON AES : ON Lens Mode : 1.00 (100%) APS : ON Print Quantity : 1 Finisher : OFF* Output mode for machine without Finisher : Sort
*: The copier with Finisher will output copies on the Finisher lower tray.
Select other copying features that are compatible with the Interrupt mode, if desired. 6 Press [START]. 7 When Interrupt copying is completed, press [INTERRUPT] again to return to the settings of the initial job. 8 Replace the initial original, then press [START] to resume copying.
NOTE: 1 In Reserve mode, pressing [INTERRUPT] before the copier finishes scanning the reserve job originals clears the settings selected for the reserve job. 2 When [CHECK] is pressed during Interrupt Copying, the information displayed reflects the initial copy job settings. Check mode will not display Interrupt copy job information. 6-32 Basic Operations
Use the [HELP] key to access information about the current screen mode and to learn about setting procedures. The [HELP] key can be pressed from any screen except Job Memory and Key Operator Screens. The Help Mode Screen also includes the Help menu icon in the lower left of the Help Screen. When touched, the Help Menu Screen displays a list of all of the copier functions. When a function item is touched, the Help Screen displays information specific to that topic. The Key-Ope mode key is also provided in the lower left corner of the Help Screen. When touched, the Key Operator Password Entry Screen wll be displayed to access the Key operator mode. See p. 11-2.

7-8 Output Modes

Group Mode (continued)
NOTE: When using the group mode do not touch TRAY1.
Touch GROUP. Touch OK to complete the setting and return to the Basic Screen. Select additional copying features, as desired. Enter the desired print quantity. Position original(s) FACE UP in the document feeder or FACE DOWN on the platen glass. 8 Press [START].

Output Modes 7-9

The Staple-sort mode is available when the offset-stacker finisher is installed. Use this mode when you want to offset and staple each copied set. Each finished set will be offset on the Finisher middle/lower tray from the next copied set.
Paper size: 11"x17", 8.5"x14", 8.5"x11", 8.5"x11"R, 5.5"x8.5"R (1 staple only), A4R, A4 Paper capacity for 20 lb: Paper exits to the middle/lower tray only. 500 sheets (8.5"x11", 8.5"x11"R, A4R, A4) 300 sheets (11"x17", 8.5"x14", 5.5"x8.5"R) Staple capacity: 50 sheets 20 lb (5.0mm thick or less) (Staple capacity is changeable, and may be set to 45, 40, or 35 by service.) 20 sheets 32 lb in thick paper mode (Staple capacity is changeable, and may be set to 25, 15, or 10 by service.) Staple location: 1 parallel staple 8.5"x11"R, 5.5"x8.5"R, A4R, Aoblique staple 11"x17", 8.5"x14", 8.5"x11", A4R, Aparallel staples 11"x17", 8.5"x14", 8.5"x11", 8.5"x11"R, A4R, A4 Incompatible: Using platen glass (Platen memory copy can use platen glass), Group, Transparency Interleaving and Thick Paper in Special Paper, APS mode in Mixed original, Repeat, AUTO Layout, Non-Image Area Erase

1 oblique staple

1 parallel staple

2 parallel staples

7-10 Output Modes
Staple-Sort Mode (continued)
Staple Location Selection Screen

Output Modes 7-11

1 Press [OUTPUT] to display the Output Mode Screen. 2 Touch STAPLE SET. The Staple Location Selection Screen will be displayed. 3 Touch the desired key among the eight keys on the Staple Location Selection Screen to select the staple location. See the previous page for reference. 4 Touch OK on the Staple Location Selection Screen to return to the Output Mode Screen. The STAPLE and SORT modes are highlighted. 5 Touch TRAY2 or TRAY3.
NOTE: When using the staple-sort mode do not touch TRAY1.
6 Touch OK on the Output Mode Screen to complete the setting and return to the Basic Screen. 7 Select additional copying features, as desired. 8 Enter the desired print quantity. 9 Position originals FACE UP in the document feeder. 50 originals can be set. When using Platen memory copy, position original FACE DOWN on the platen glass and touch SCAN on the Basic Screen to scan.

Adding Toner

Shortcuts 10-1

Shortcuts

Reserve Job (see p. 6-17)
1 Touch RESERVE while a current job is in progress to display the reserve job setting screen. 2 Select the copying conditions for the reserve job. 3 Position the reserve job original(s) face up on the RADF (document feeder) tray or face down on the platen glass. 4 When using the Platen Memory mode, touch Store Mode to store the image. If Platen Memory is not selected, press [START] to store the image. 5 When all reserve settings are completed, press [AUTO RESET] to release the reserve setting mode. 6 Then, touch SETTING to return to the Basic Screen, which displays the current job in progress. When copying is completed for the current job, the Basic Screen will display the copy settings for the reserve job. 7 Press [START]. Copying for the reserve job will start.
Platen Store Mode (see p. 6-23)
1 Make copying selections, then select the 1-1 or 1-2 copy mode. 2 Press [APPLICATION] to display the Application Selection Screen, then touch Store Mode to highlight the store mode. 3 Touch OK to return to the Basic Screen. 4 In turn and in order of pagination, position each original face down on the platen glass then close the document feeder (or platen cover). 5 Touch SCAN to scan and store the original image into memory. 6 Repeat Steps 4 and 5 until all originals are scanned. Be sure to touch SCAN for each original. 7 When all originals are stored, enter the print quantity amount. 8 Press [START] to begin copying.
RADF Store Mode (see p. 6-25)
1 Make copying selections. 2 Press [APPLICATION] to display the Application Selection Screen, then touch Store Mode to highlight the store mode. 3 Touch OK to return to the Basic Screen. 4 Enter the print quantity amount. 5 Position no more that 50 originals at a time face up on the RADF (document feeder) tray. 6 Touch SCAN to scan and store the original image into memory. 7 Repeat Steps 5 and 6 until all originals are scanned. 8 Press [START] to begin copying.

10-2 Shortcuts

Sheet/Cover Insertion (see p. 8-3)
1 Press [APPLICATION] to display the Application Selection Screen. 2 Touch Sheet/Cover Insertion to display the Sheet/Cover Insertion Screen. 3 Touch TRAY1 or BYPASS to select the tray source for cover stock. To insert thick paper for cover, touch THICK PAPER. BYPASS will automatically be selected. 4 Select Front Cover Insertion, then touch FRONT COPY or FRONT BLANK. 5 Select Back Cover Insertion, then touch BACK COPY or BACK BLANK. 6 Select Sheet Insertion, then COPY INSERTION or BLANK INSERTION. 7 Touch OK to display the Page Setting Screen. 8 Touch the 15 blank boxes in turn to designate each insertion location. 9 Touch SET after each entry. 10 When all page numbers are entered, touch OK. 11 Enter the print quantity amount. 12 Position originals face up on the document feeder tray. 13 Press [START]. When copying is completed, press [AUTO RESET] to reset the machine.

Special Original: Mixed Original (see p. 8-23)
Press [APPLICATION] to display the Application Selection Screen. Touch Special Original to display the Special Original Screen. Touch Mixed Original. Touch OK to return to the Application Selection Screen. Make additional copying selections. Touch OK to return to the Basic Screen. Select APS to copy onto various paper sizes to match the original sizes, or select AMS mode to copy all originals onto one common paper size. 8 Enter the print quantity amount. 9 Position mixed originals face up on the RADF (document feeder) tray. Combine ledger, legal, letter, and 5.5"x8.5" or legal, letter R, letter, and 5.5"x8.5". 10 Press [START]. When copying is completed, press [AUTO RESET] to reset the machine. 7

10-6 Shortcuts

Special Original: Folded Original (see p. 8-25)
9 Press [APPLICATION] to display the Application Selection Screen. Touch Special Original to display the Special Original Screen. Touch Folded Original. Touch OK to return to the Application Selection Screen. Make additional copying selections. Touch OK to return to the Basic Screen. Enter the print quantity amount. Position folded originals face up on the RADF (document feeder) tray. Press [START]. When copying is completed, press [AUTO RESET] to reset the machine.
Special Original: Non-Standard Original (see p. 8-27)
9 Press [APPLICATION] to display the Application Selection Screen. Touch Special Original to display the Special Original Screen. Touch Non-standard Size. Touch OK to return to the Application Selection Screen. Make additional copying selections. Touch OK to return to the Basic Screen. Enter the print quantity amount. Position non-standard size originals face up on the RADF (document feeder) tray. Press [START]. When copying is completed, press [AUTO RESET] to reset the machine.
Special Original: Upside Down (see p. 8-28)
1 Press [APPLICATION] to display the Application Selection Screen. 2 Touch Special Original to display the Special Original Screen. 3 Touch 1-2 Upside down or 2-1 Upside down, as desired. The subsequent screen for selecting binding type will be displayed. 4 Touch Left/Right bind or Top/Bottom bind. 5 Touch OK to return to the Special Original Screen. 6 Touch OK to return to the Application Selection Screen. 7 Make additional copying selections. 8 Touch OK to return to the Basic Screen. 9 Enter the print quantity amount. 10 Position originals face up on the RADF (document feeder) tray. 11 Press [START]. When copying is completed, press [AUTO RESET] to reset the machine.

Shortcuts 10-7

Text/Photo Enhance (see p. 8-30)
Press [APPLICATION] to display the Application Selection Screen. Touch Text/Photo Enhance to display the Text/Photo Enhance Screen. Touch INCREASE CONTRAST, TEXT, or PHOTO. Touch OK to return to the Application Selection Screen. Make additional copying selections. Touch OK to return to the Basic Screen. Enter the print quantity amount. Position original(s) face up on the RADF (document feeder) tray or face down on the platen glass. 9 Press [START]. When copying is completed, press [AUTO RESET] to reset the machine.

Reverse Image (see p. 8-32)
1 Press [APPLICATION] to display the Application Selection Screen. 2 Touch Reverse Image to switch from the black-on-white copying mode to white-onblack copying. 3 Touch OK to return to the Application Selection Screen. 4 Make additional copying selections. 5 Touch OK to return to the Basic Screen. 6 Enter the print quantity amount. 7 Position original(s) face up on the RADF (document feeder) tray or face down on the platen glass. 8 Press [START]. When copying is completed, press [AUTO RESET] to reset the machine.

10-8 Shortcuts

Repeat (see p. 8-33)
1 Press [APPLICATION] to display the Application Selection Screen. 2 Touch Repeat to display the Repeat Mode Selection Screen. 3 Select the Vertical/Horizontal width setting mode, the AUTO detection mode, or the Repeat mode. With the Vertical/Horizontal width setting mode, touch Vert./Horiz., then enter the vertical and horizontal widths of the scanning area. With the AUTO detection mode, touch AUTO to allow the machine to set equal repeat areas according to the size of the original with non-image area erase functioning. With the Repeat mode, touch Repeat, a portion of the selected copy size equally divided according to the mode (2 Repeat, 4 Repeat, or 8 Repeat) designated on the screen. 4 Touch OK to return to the Application Selection Screen. 5 Make additional copying selections. 6 Touch OK to return to the Basic Screen. 7 Enter the print quantity amount. 8 Position original(s) face down on the platen glass. If you selected the AUTO detection mode, DO NOT CLOSE THE DOCUMENT COVER. If you selected the Repeat mode, the RADF (document feeder) can be used. 9 Press [START]. When copying is completed, press [AUTO RESET] to reset the machine.
Frame/Fold Erasure (see p. 8-37)
Press [APPLICATION] to display the Application Selection Screen. Touch Frame/Fold Erasure to display the Frame/Fold Erasure Setting Screen. Touch Frame Erasure and enter a value or use the current setting. Touch Fold Erasure and enter a value or use the current setting. Touch OK to complete the setting and return to the Application Selection Screen. Make additional copying selections. Touch OK to return to the Basic Screen. Select copy size and enter the print quantity amount. Position original(s) face up on the RADF (document feeder) tray or face down on the platen glass. 10 Press [START]. When copying is completed, press [AUTO RESET] to reset the machine. 9

Shortcuts 10-9

3. Preset key

4. ECM
5. Lock Job memory [Job lock/unlock; Delete] 6. Paper type 7. Panel contrast 8. Key ope. data 9. Weekly timer [Recycle; Color; Letterhead; Special; Label; Invoice; Legal; Blank] [Contrast Dark/Normal/Light; Backlight Dark/Normal/Light] [Name; For assistance] 1. 2. 3. 4. 5. Weekly timer setting Weekly timer copier on/off time set Machine working day individual set Lunch hour off function Password setting

10. Touch panel adj

11-4 Key Operator Mode
Function Menu Map (continued)
FUNCTION MENU 11. Power save SUB FUNCTION MENU AND SETTING OPTIONS Auto low power timer: [5, 10, 15, 30, 60, 90, 120, 240] Auto shut off timer: [15, 30, 60, 90, 120, 240] Auto shut off: [on; off] 1. Auto reset timer 2. AUTO/RESET effect 3. Load RADF effect 4. Non image area erase 5. RADF frame erasure 6. Auto tray switch 7. Platen APS 8. RADF APS 9. ATS/APS (bypass) 10. ATS/APS SW (tray 1) 11. ATS/APS SW (tray 2) 12. ATS/APS SW (tray 3) 13. ATS/APS SW (tray 4) 14. Platen AMS 15. RADF AMS 16, Staple mode reset 17. Key click sound 18. Job memory recall 19. Sheet insertion 20. 5.5"x8.5" original type 21. Rotation 22. 1 shot indication [Job memory list; User setting list; Font pattern]

12. Memory SW

13. List print
14. Appli. customize [File Edit; Image Edit] 15. Density Shift 16. KRDS host [Density shift 0; 1; 2; 3; 4; 5] 1. 2. 3. 4. 5. 6. JAM concerns SC concerns NO TONER NO PAPER COPY QUALITY OTHER REASON

Key Operator Mode 11-5

System Initial [1]
Set the following initial conditions of the copier. Time: Current date and time, summer time Language: Language used in LCD ( English)

Time [1]

Set the current date and time, and also the summer time.
Default setting: Summer time off
Key Operator Mode Screen System Initial Setting Menu Screen Time Setting Screen
1 Press [HELP] to display the Help Screen, then touch Key-Ope mode. Enter a 4-digit key operator password, then touch OK to display the Key Operator Mode Screen.
2 Touch 1. System Initial to display the System Initial Setting Menu Screen, then touch 1. Time to display the Time Setting Screen. 3 Adjust the time. The time that the copier currently has is displayed in the upper line, in the order of date, month, year, and time (in 24-hour expression). (1) Touch the left arrow (<<) and right arrow (>>) keys displayed under the SET TIME to move the cursor to the number to be changed. (2) Press the keypads on the Control panel to enter the number. 4 To activate the summer time function, touch SUMMER TIME to highlight it.

5 Touch the timer key displayed under the Auto Shut off indicator on the Power Save Timer Setting Screen, to select the period of time to wait before activating Auto Shut Off. The default setting is 60 min.
NOTE: If the period of time selected for Auto Shut Off is shorter than the Auto Low Power setting, the setting for Auto Low Power will be automatically changed to that of the Auto Shut Off setting, and the Auto Low Power indicator light will dim. In this case, Auto Low Power will not function.
6 Touch NEXT on the Timer Setting Screen to display the Auto Shut Off ON/OFF Setting Screen. 7 Touch ON to activate Auto Shut Off, or touch OFF to de-activate it. The default setting is the ON setting. When OFF is selected, Auto Shut Off will not function and the period of time for Auto Low Power can be selected from 5, 10, 15, 30, 60, 90, 120, and 240min. 8 Touch RETURN to restore the Key Operator Mode Screen. If other key operator settings are required, select the desired menu item. 9 If no further changes are required, touch RETURN to restore the Basic Screen to perform copying operations.

Key Operator Mode 11-45

Memory Switch [12]
This function allows you to change the Memory Settings listed below. Underlined settings indicate factory settings. See pp. 11-48~11-50 for details on Memory Settings. SW No. Item No.01: No.02: No.03: No.04: No.05: No.06: No.07: No.08: No.09: No.10: No.11: No.12: No.13: No.14: No.15: No.16: No.17: No.18: No.19: No.20: No.21: No.22: Auto reset timer AUTO/RESET effect Load RADF effect Non Image A. Erase RADF frame erasure Auto tray switch Platen APS RADF APS ATS/APS (Bypass) ATS/APS SW (Tray 1) ATS/APS SW (Tray 2) ATS/APS SW (Tray 3) ATS/APS SW (Tray 4) Platen AMS RADF AMS Staple mode reset Key click sound Job memory recall Sheet insertion 5.5x8.5 orig. type Rotation 1 SHOT Indication Setting (default is underlined) OFF/ 30sec./ 60 sec./ 90 sec./ 120 sec./ 150 sec./ 180 sec./ 210 sec./ 240 sec./ 270 sec./ 300 sec. Full-auto/ Initial setting RADF/ RADF + AUTO RESET ON/ APS/AMS only None/ 1 mm/ 2 mm/ 3 mm/ 4 mm/ 5 mm OFF/ ON OFF/ ON OFF/ ON OFF/ ON OFF/ ON OFF/ ON OFF/ ON OFF/ ON OFF/ ON OFF/ ON OFF/ ON OFF/ Low/ High OFF/ ON Tray 1/ Tray 2/ Tray 3/ Tray 4/ Bypass Landscape/ Portrait OFF/ ON/ APS/AMS/reduce/ APS/AMS only/ APS only 1 sec./ 2 sec./ 3 sec./ 4 sec./ 5 sec.

11-46 Key Operator Mode

Memory Switch [12] (continued)
Key Operator Mode Screen 1 Key Operator Mode Screen 2 Memory Switch Screen 1

Memory Switch Screen 2

Memory Switch Screen 3
2 To display menus 11. to 16. of the Key Operator Mode Screen, touch the Lower arrow key. 3 Touch 12. Memory SW to display the Memory Switch Screen. The Memory Switch Screen can be scrolled to the third screen. 4 Use the procedure below to select the desired item and change the setting. (1) Use Upper arrow and Lower arrow keys at the lower left on the Memory Switch Screen to scroll the screen. (2) Touch Upper arrow or Lower arrow key at the right on the Memory Switch Screen to highlight the desired item. (3) Touch EDIT to change the setting of the highlighted item. (4) Repeat above steps (1) to (3) to make several changes in succession. 5 Touch RETURN to restore the Key Operator Mode Screen. If other key operator settings are required, select the desired menu item. 6 If no further changes are required, touch RETURN to restore the Basic Screen to perform copying operations.

Troubleshooting 13-13

Section 14 : Machine Specifications
Machine Specifications 14-1
Product Name Konica 7045 Configuration Console with stationary platen Photoreceptor OPC drum Method Laser Electrostatic Toner Black, cartridge type Recommended Operating Environment 50~86F (10~30C); 10~80% RH Warm Up Approx. 90 sec. @68(20C); 50% RH Auto Reset Off/30 sec./1 min./1.5 min./2 min./2.5 min./ 3 min./3.5 min./4 min./4.5 min./5 min. First Copy Out Time From Platen Glass: 3.9 sec. for 8.5"x11" Copy Rate 45 cpm: 8.5"x11" 32 cpm: 8.5"x11"R 27 cpm: 8.5"x14" 23 cpm: 11"x17" 41 cpm: 5.5"x8.5" Continuous Copy 1~999 copies Copier Power Source 120V10%/15A; 60Hz2.5Hz Power Consumption Max. 1,500VA (full option) Copying: 1,300 VA (full option) Noise Level (full system) Approx. 59 dB (A) or less, during copying Automatic Modes AMS; AES (plus 9-level manual density); APS detects 11"x17", 8.5"x14", 8.5"x11"R, 8.5"x11", 5.5"x8.5" Magnification Presets; 0.50, 0.65, 0.77, 1.00, 1.29, 1.55, 2.User Sets - 0.25~4.00, set by key operator Zoom range - 0.25~4.00 in 1% steps Originals on Platen Max. size: 11"x17" (280mmx432mm)
Specifications Subject To Change Without Notice
14-2 Machine Specifications
Originals in Document Feeder ADF mode: 1>1; 1>2 11"x17"; 8.5"x14"; 8.5"x11"R; 8.5"x11"; 5.5"x8.5"R, 5.5"x8.5" Max. 50 sheets (20 lb) feed/exit capacity RADF mode: 2>2; 2>1 11"x17"; 8.5"x14"; 8.5"x11"R; 8.5"x11"; 5.5"x8.5"R, 5.5"x8.5" Max. 50 sheets (20 lb) feed/exit capacity Mixed mode: 11"x17"+8.5"x14"+8.5"x11"+5.5"x8.5" or 8.5"x14"+8.5"x11"R, 8.5"x11", 5.5"x8.5" Max. 50 sheets (20 lb) feed/exit capacity Original weight: 20~24 lb bond; curl max. 10 mm or less (Transparency, Paste-up, Offset master, Labels, & Intermediate papers unavailable) Paper Source Main body trays 1/2/3/4; 500/500/1,000/ 1,500 sheets Multi-sheet bypass tray; 100 sheets Trays 1/2/3/4 user adjustable Paper Exit Tray 100 sheets (20 lb) Paper Weight 20 lb~24 lb bond recommended (Max. range: 16 lb~19 lb, 25 lb~32 lb) Transparency film, Labels, 3-hole Main Body Safety Standard UL 1950; CSA 22.2 No. 950 -93 Radio Interference FCC Rules part 15, sub-part B Class A Memory 32 MB (max. 288 MB) Options Finisher (FS-109) Drawer base unit (DB-208) Drawer base unit (DB-208A) Drawer base unit (DB-608) Expanded Memory Unit (MU-403: 32 MB, MU-404: 64 MB, MU-405: 128 MB) Remote Diagnostics External Image Processor (IP-431) Network Interface Board(KN-303) Hard Disk Drive (HD-103) PostScript 3 (PS-342) Key Counter

Non-Image Area Erase (Application) 8-42 Non-Image Area Erase (Memory switch) 11-48 Non-Image Erase 11-15 Non-Sort Mode 7-4 Non-Standard Size 8-27 Normal Exit 7-14, 7-16 NUMBERING 8-44

4 Index

RADF (Reversing Automatic Document Feeder) 3-3 RADF AMS 11-49 RADF APS 11-49 RADF frame erasure 11-48 RADF Hinges 2-9 RADF mode 4-3 RADF Store Mode 6-25 RE key 6-10 Rectangular erase mode 8-42 Reduce & Shift 8-41 Release lever 3-5 Remote Diagnostics 11-55 Repairs 12-11 Repeat 8-33 Report code No. 13-2 Reserve 6-17 RESERVE key 6-17 Reverse Image 8-32 Right binding key 8-13 Rotation 6-26 Rotation (Memory switch) 11-50 Rotation Exit 7-15, 7-17 Rotation+Group exit 7-15, 7-17 Rotation icon 6-2 Rotation+Sort exit 7-15, 7-17 Staple mode reset 11-49 Staple position icon 6-2 STAPLE SET key 7-12 Staple Sheet Capacity 3-11 Staple-Sort Mode 7-10 START key 3-7 STOP/CLEAR key 3-7 Storage 3-3 Store Mode 6-23 Store Mode key 6-23 SUMMER TIME key 11-6 Supplies 12-11 System Initial 11-6
Temperature and Humidity 2-6 Text Mode 8-30 Text/Photo Enhance 8-30 THICK PAPER key 8-16 THIN PAPER key 8-16 Thin/Thick Paper 8-16 Time (System Initial) 11-6 TIMER indicator 3-7 Timer Interrupt 5-5 Timer interrupt password 5-5, 11-42 Toner 2-9 Toner cartridge 3-4, 12-7 Toner unit 3-4, 12-7 Top/Botom bind key 8-29 Total counter 3-4 Touch Panel Adjustment 11-43 Touch Screen 3-8 Transparency Interleaving 8-14 Tray (Copier Initial) 11-12 Troubleshooting Tips 13-11
SCAN key (control panel) 3-7 SCAN key (touch screen) 6-2, 6-24 Service 12-11 Service call icon 6-33 Service Messages 2-9 Service Settings 3-11 SETTING indicator 6-19 Sheet Insertion 11-50 Sheet/Cover Insertion 8-3 Short Circuit from Water Damage 2-6 Simplex copy 6-4 Site Requirements 3-6 SORT key 7-7 Sort Mode 7-6, 7-16 Sort with normal exit 7-14 Space Allotment 2-6 Special Original 8-23 Special Paper 8-14 Special Ratio Table 6-12 STAMP 8-44 Standard Equipment 1-12 Staple cartridge 12-8 Staple drive portions 3-5 STAPLE key 7-12
Universal tray 12-3 Unsuitable RADF Originals 4-3 Upper right side cover 3-3 Upside Down 8-28 User Name 11-21 User setting list 11-51 USERSET 1, 2, 3 (Magnification) 11-18 Userset 1, 2 (Density) 11-16
Ventilation 2-6 Vertical/Horizontal Width Setting mode 8-33 Vertical/Horizontal Zoom 6-13 Vibrations 2-6

Index 5

Warming up message 6-2 WARNING 2-3 WATERMARK 8-44 Web Site Address (copyright page) Weekly Timer 11-33 Weekly Timer Copier ON/OFF Time Set 11-36 Weekly Timer Function 5-5 Weekly Timer Master Key Code 3-11, 11-33 Weekly Timer Setting 11-35 Work table 3-3

SSD SUPPORT SOLUTIONS

7045 - ALL ACTIVE SOLUTIONS September 2007
This document contains information that was exported directly from Konica Minolta's SSD Support knowledge base. Some solutions may contain hyperlink references which originally contained links to graphic or text files. If you wish to view these files, you must access the solutions via SSD CS Expert Support on Konica Minolta's website, www.kmbs.konicaminolta.us.
Legal Notice This document is designed as a diagnostic tool, primarily for Konica Minolta's support personnel, and authorized service representatives. Konica Minolta recommends that all service be performed by an authorized service representative. Users are responsible for seeking advice of a Konica Minolta authorized service representative regarding the information, opinion, advice or content of this document. USER AGREES THAT USE OF THIS DOCUMENT IS AT USER'S SOLE RISK AND THAT THIS DOCUMENT IS PROVIDED ON AN AS IS BASIS WITHOUT WARRANTIES OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, WARRANTIES OF TITLE OR IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, OTHER THAN THOSE WARRANTIES THAT ARE IMPLIED BY LAW AND INCAPABLE OF EXCLUSION. IN NO EVENT WILL KONICA MINOLTA OR THOSE ACTING ON ITS BEHALF BE LIABLE FOR ANY DAMAGES, INCLUDING, WITHOUT LIMITATION, DIRECT, INDIRECT, INCIDENTAL, SPECIAL, CONSEQUENTIAL OR PUNITIVE DAMAGES ARISING OUT OF YOUR USE OF THIS DOCUMENT.
Copyright 2007, Konica Minolta Business Solutions U.S.A., Inc.
Solution ID TAUS0613779EN* Solution Usage 29
Description Intermittent F87-03 and/or Printer Board Failure messages only when an IP431 is installed. Solution CAUSE: During initial install, if the machine and IP unit are not allowed to boot up completely, the code from the CF card(s) will not be written completely to the hard drive. This may occur if the machine is powered OFF prematurely to access the 25, 36 or 47 adjustment mode. The code written to the hard drive will be partial and the IP will be unable to boot the next time power is applied. SOLUTION: If unable to reformat the hard drive from the operation panel, remove the HD103 and recover by installing it in a PC. Use a Microsoft* Windows 98 boot disk and the fdisk utility to clean and reformat the drive on a PC. The following instructions explain how to use an IDE adapter to attach the HD107 to a standard PC to reformat the drive: 1. A 2.5" laptop IDE hard drive adapter. This adapter can be found at most computer stores that sell a wide variety of cables and adapters. One online source for this adapter is [[www.cablesonline.com| URL http://www.cablesonline.com]]. 2. An IP controller or standard PC. The IDE adapter will need to be plugged into a standard IDE cable that is connected to the master channel of the PC or IP controller. Power is supplied by the IP/PC's power supply through a standard power connector. 3. Use a Microsoft Windows 98 boot disk which can be created on a Windows 98 workstation. 4. Connect the hard drive to the 40-pin connector on one side of the adapter and connect the IP/PC's IDE cable to the 44-pin connector on the other side of the adapter. Ensure that Pin 1 on the IDE connector and hard drive is connected to Pin 1 on the adapter. 5. Insert the 98 Boot disk into the floppy drive of the IP/PC, reconnect the IP/PC power cord, and power ON the IP/PC. 6. Once the IP/PC boots from the floppy, press return at the date and time prompts to get to the A: prompt. 7. Use FDISK to create a primary DOS partition and set it as active. WARNING: Do not use large disk support. 8. Format the newly-created partition with the /s switch to transfer system files. =================================C A U T I O N================================= If the hard drive is not connected to the IDE master channel, and is not configured to be the MASTER drive, the setup program will format whatever drive is connected and setup as the MASTER drive. ============================================================================= 9. Remove the hard drive from the PC and reinstall it the IP unit. Allow the IP and main body to completely boot or this process will have to be repeated. * Trademark ownership information Solution ID TAUS0614523EN* Solution Usage 13

Description What Konica Minolta print drivers will come bundled with Microsoft Windows Vista and what is the release schedule for Vista-compatible drivers? Solution Please refer to the Windows Vista Hardware Compatibility List for Printers &amp; Scanners and the attached PDFs. For EFI legacy products that will not receive a Vista-specific driver, refer to the following statement: "The previous drivers ( System 5/5e-8/8e ) will not work on 64-bit Vista. However, these drivers will work on the 32-bit version of Windows Vistawith minor issues." Known issue : Borders and frames around icons and panes within the driver UI may not show up correctly. Notes : 1. Ifa previous driver was Microsoft Windows XP WHQL certified, Microsoft also honors the digital signature (CAT file) on Windows Vista. 2.To view a PDF, Adobe Reader must be installed. Adobe Reader can be downloaded for free from the Adobe web site at: http://www.adobe.com/products/acrobat/readstep2.html

Solution ID Description

TAUS0657724EN*

Solution Usage

How to access the Konica Minolta FTP site. Solution The Konica Minolta FTP site is no longer accessible. The content of this site has been transferred to the Drivers/System Code/Firmware/EPROMs selection on each individual's SSD Home page. Enter a Product Group, and a Product and select Go to get a complete list of Drivers, System Code, Firmware, EPROMs, Utilities, and Support Documentation. In addition there arelinks to download Firmware, EPROMs, Utilities, and Support Documentation for related accessories. Solution ID Description TAUS0700453EN* Solution Usage 78
NVRAM Troubleshooting Procedure used to identify NVRAM problems. Solution C250/C252/C300/C350/C351/C450 NVRAM trouble codes ( C-D3xx codes ) can occur at any time. Mostly these codes happen when updating firmware. A NVRAM Data Restore procedure was announced a few months ago to address these codes: Stop, 0, 7, 1, 3, 9, * What this procedure does is take a good image of the NVRAM off the MFP board (created when you performed the NVRAM Data Backup) and restore it to the NVRAM. There are approximately 30 registers that can be corrupt, so the above procedure may have to be done as much as 30 times. WARNING : If a corrupt NVRAM is suspected, DO NOT perform the NVRAM Data Backup. This will take the corrupt NVRAM image and back it up to the MFP board. If this is done, and the NVRAM is replaced, the corrupt data that was just backed up will be transferred to the new NVRAM. If this is the case then the NVRAM and MFP board will have to be replaced as a set. Known unrecoverable NVRAM symptoms: 1. Stuck on hour glass screen 2. Incorrect meters 3. When performing the NVRAM restore procedure the codes repeat themselves Note : One thing that has been noticed is these machines seem to be highly susceptible to voltage sags and spikes. It is HIGHLY recommended to install a quality power line conditioner on these machines. Known fixes for various codes: C-D36E and C-E002 Install Phase 3.01firmware (H5 or H6 depending on model). If a corrupt NVRAM is suspected, please try performing a Data Clear. This can be found in the Tech Rep mode. IMPORTANT : All programmed addresses will be cleared. Please backup the address data using PageScope Web Connect to backup the data before performing the Data Clear. If NVRAM replacement is necessary please be aware that the meters may not be transferred and they might be reset to zero. This is unrecoverable and the correct meters cannot be input. 8020/CF2002/8031/CF3102 Codes C-3C00 through C-3C40 Codes C-3C50 through C-3C90 indicate a corrupt BRU indicates a problem with the PWB-C board or the scanner to main body cable.

Description NVRAM/BRU replacement form. Solution The online NVRAM/BRU Replacement RA/Claim formis referencedin attached Bulletin Number 5783. Notes : 1. AN SSD TICKET NUMBER MUST BE ASSIGNED IN ORDER TO PLACEA NVRAM/BRU ORDER ONLINE. All requests for NVRAMs must be approved by the SSD Hotline and a problem ticket generated. If a request is received without an established problem ticket number, the request will be denied. 2. To view a PDF, Adobe Reader must be installed. Adobe Reader can be downloaded for free from the Adobe web site at: http://www.adobe.com/products/acrobat/readstep2.html

TAUS0618161EN*

Description Intermittently, a one inch gray background band in the front-to-rear direction is present on the lead edge of a copy produced after the machine has sat idle for 30 or more minutes. Solution CAUSE: Use of non - Konica Minolta drum. SOLUTION: Replace the drum with an authentic Konica Minolta drum. Solution ID TAUS0614076EN* Solution Usage 149
Description Intermittent E56-01 at power up. Solution CAUSE: Loss of communication from the image control board (ICB) to the main CB. SOLUTION: Separate the ICB from the main CB and inspect the connection point (CN10) for any obstruction or damage. Reseat the ICB and verify operation. If problem persists, replace the ICB (p/n 55YA-9020).
Solution ID TAUS0614635EN* Solution Usage 146
Description Intermittent J16 when copying from the platen glass or document feeder. Solution CAUSE: Incorrect Software SW setting. Note: While copying from the glass, when touching the print button and L1 is performing APS the paper will prematurely feed causing a J16. SOLUTION: To change software SW setting perform the following; 1. Access the 25 mode (power machine OFF/ON while pressing the 2 and 5 keys). 2. Memory setting mode will be displayed. 3. Press [1. Software SW]. 4. Software SW will be displayed. 5. Scroll to dipswitch 2-2. 6. Press the OFF button on the touchscreen to change the setting to a 0. 7. Press [RETURN] to exit the Software SW mode. 8. Power OFF/ON. Solution ID TAUS0618237EN* Solution Usage 64
Description FS109, FINISHER TRAY FAILURE message during initialization. Solution PROBABLE CAUSES: 1. PS806 (tray lower limit detect sensor) is not being actuated. Visually inspect PS806 to see if it is being actuated. If PS806 is not being actuated, inspect for any binding in the paper exit tray. To check the operation of PS806, perform the following: a. Access the 47 multimode (power the copier ON, while simultaneously holding the 4 and 7 keys), input code 70, press P-06-P. The touchscreen should indicate ON if PS806 is being actuated. b. If PS806 is actuated, and the touchscreen indicates OFF, check for 5V DC at CN703-A3 on the FNCB (finisher control board)(p/n 13LP-9010). c. If 5V DC is not present at CN703-A3, power the machine OFF and remove CN703. d. Power the machine ON, and check CN703-A3 for 5V DC. e. If 5V DC is present, check for any pinched wires going to PS806 and replace as necessary (p/n 12QV85510). Note: If the finisher is disconnected and a management list is printed, F77-2 will be incremented on the jam list. 2. MS804 is not providing 24V DC to CN709-1 when it is ON. MS804 is wiring normally open. When the stapler safety (PV) plate is engaged the contacts of MS804 should be closed. Confirm 24V DC at CN709-1 when MS804 is actuated. If voltage is not present, replace MS804 (p/n 12QR86010). Solution ID TAUS0613431EN* Solution Usage 43

Description How to prevent a paper tray containing special paper (i.e., letterhead, colored paper) from being selected as the default tray. Solution To exclude a specific paper tray as the default, perform the following: 1. Access Memory Switch 12 in the Key Operator Mode. Press Help, Key-Ope Mode and then the down arrow in the lower left corner for the next page. 2. Select 12. Memory SW. 3. Press the down arrow in the lower left corner for the next page of memory switches. 4. Press the down arrow on the right hand side to select ATS/APS of the tray containing the special paper. 5. Use the EDIT key to toggle tray selection ON/OFF. To deselect the tray, toggle to OFF. 6. Press Return to exit the Key Operator Mode. Solution ID TAUS0614381EN* Solution Usage 5
Description How to set non-image erase area for randomly placed originals (oblique mode). Solution SOLUTION: To program the non-image erase area for randomly placed originals (oblique mode) or standard sized originals (rectangular mode), perform the following: 1. Access the Key Operator Mode (press and hold the help key while powering the machine ON). 2. Select 2: Copier Initial. 3. Select 6: Non-image Erase. 4. Press either (oblique erase) or (Rectangular erase). 5. Press OK. 6. Power the machine OFF/ON to exit the Key Operator Mode. Solution ID TAUS0614595EN* Solution Usage 5
Description Dark/background copies. Solution CAUSE: Main charge corona unit is not completely seated in the drum carriage. SOLUTION: Reseat the main charge corona unit so that it sits parallel to the drum.

TAUS0614886EN*

Description PLEASE WAIT FRONT DOOR IS OPEN message at power up. Solution CAUSE: A loss of 24V DC to the printer DB. SOLUTION: Ensure that there is 24V DC at CN32-A28 on the printer DB. The 24V DC is supplied by DCPS1 (CN381-6) through MS1. One possible cause is a loose pin A28 on CN32 of the printer DB. Solution ID TAUS0614981EN* Solution Usage 5
Description How to clear fuser abnormality codes (F34, F35, F36), 7045. Solution To reset fuser codes, perform the following: 1. Power the copier OFF. 2. Access the 25 mode (power the machine ON, while pressing the 2 and 5 keys). 3. Touch [1: Software SW] on the touchscreen. 4. Select software dipswitch [3] using the left up-arrow on the touchscreen. 5. Select bit number [1] using the middle up-arrow on the touchscreen. 6. Touch [OFF] on the touchscreen to set the dipswitch to (0). 7. Power the machine OFF/ON to exit the 25 mode. Solution ID TAUS0615070EN* Solution Usage 5

Description How to adjust the touchscreen sensitivity. Solution To adjust the touchscreen sensitivity, perform the following: 1. Power the copier OFF. 2. Access the Key Operator Mode (power the copier ON, while pressing the HELP key). 3. Touch [10. Touch panel adj] on the touchscreen to access the control panel adjustment screen. Note: If the touchscreen is so far out of adjustment that there is no response when touching [10. Touch panel adj], the control panel adjustment can be accessed by touching any numeric key on the key pad. Two plus symbols (+) should be visible on the screen. 4. Touch [+] at the upper right corner lightly with a touch pen (something with a round tip made of resin is recommended). 5. Touch [+] at the lower left lightly with a touch pen. 6. Ensure the X coordinate and the Y coordinate displayed in the message area fall within the standard values. The acceptable values are on the second line. 7 If the values are not within acceptable parameters, repeat Steps 3 and 4 until the values are acceptable. 8. As verification of a correct adjustment, touch the blank box in the upper left and lower right corners of the touchscreen. Do not touch the box labeled [CHECK]. You should hear a beep tone for each one. If a beep tone is not heard, repeat the adjustment. 9. Press the START key when the adjustment procedure is completed. 10. Power the copier OFF/ON to exit the Key Operator Mode. Solution ID TAUS0616734EN* Solution Usage 2
Description DF315, blur or jitter on copies in the front-to-rear direction, 42mm from the trail edge, when feeding from the RADF. Solution CAUSE: Improper RADF position or height adjustment. SOLUTION: To perform the RADF position and height adjustment, perform the following: 1. Power OFF the main power switch (SW1), which is located on the left side of the copier.
2. Remove the two scale plate fixed screws (p/n 190040921), and then remove the platen stopper plate of the main body (p/n 55GA12094). 3. Install the RADF positioning jigs (p/n 120A1052) in the holes of the original stopper plate. 4. Loosen two set screws on the stopper bracket on the main body and the set screw on the DF315 stopper plate. 5. Lower RADF so the guide hole matches the adjustment jigs. 6. Slowly, lift the RADF and then tighten stopper bracket set screws. 7. Remove the two RADF positioning jigs, and then reinstall the platen stopper plate. 8. Close the RADF and ensure that the two (2) stoppers located at the front and rear of the read section contact the slit glass simultaneously. Note: Removal of the left reading cover (p/n 55GA12071) will allow clear visibility of stopper and slit glass contact points. 9. Adjust the adjustment screws (A) and (B), which are located on the top of each RADF hinge until both stoppers make contact with the slit glass simultaneously. Note: The RADF position and height adjustments are outlined in the DF315 Service Manual (11/00) on pages 19 and 20. Solution ID TAUS0616841EN* Solution Usage 2

Description ENTER 4-DIGIT PASSWORD AND PRESS OK: message after entering the 25, 36, or 47 mode. Solution CAUSE: Diagnostic mode security is enabled. This feature was designed to limit access to machine diagnostic modes by end users. SOLUTION: To access diagnostic modes with security enabled, enter the default password: 9272 and touch [OK] on the touchscreen. To disable this security feature, enter the default password and perform the following: 1. Touch [1: Software SW] on the touchscreen. 2. Select software dipswitch 7-5 using the arrow keys. 3. Set the switch to OFF (0). 4. Power the machine OFF/ON to exit the 25 mode. Solution ID TAUS0617621EN* Solution Usage 2
Description Toner addition motor (M10) turns continuously at power up. Solution CAUSE: Failed quantity detecting sensor. SOLUTION: Replace the quantity detecting sensor (p/n 40AA88030). Solution ID TAUS0617950EN* Solution Usage 2
Description Poor density; poor fill. Solution CAUSE: Dmax value not changing. SOLUTION: Replace the memory board (p/n 26NA-9110). Solution ID TAUS0619758EN* Solution Usage 2
Description FS109. not recognized by the main body. Paper will pass through the finisher, but finisher functions can not be selected. Solution CAUSE: Finisher Tray 2 and Tray 3 are not enabled (isolated) in the 25 mode. SOLUTION: To enable/disable the Finisher Tray 2/3 setting, perform the following: 1. Access the 25 mode (power the machine ON while holding down on the 2 and 5 keys). 2. Press [1: Software SW]. 3. Scroll to and set software dipswitch 20-2 as follows: a. Data 0 - Finisher tray 2/3 can be used. b. Data 1 - finisher tray 2/3 are isolated. 4. Power the machine OFF/ON to exit the 25 mode. Solution ID TAUS0619902EN* Solution Usage 2
Description Unable to clear J31.
Solution CAUSE: PS309 (original reversal detect) failed. SOLUTION: To check PS309, perform the following: 1. Access the 47 multimode (power the machine ON while holding down on the 4 and 7 keys), input code 60, P-6-P. 2. Actuate PS309 and watch for a change of state on the control panel. 3. If no change takes place, clean or replace PS309 (p/n 12OA85520). Solution ID TAUS0622389EN* Solution Usage 2
Description DF315, J65-2 and jam position 13. Solution CAUSE: PS308 (original feed detect) is always ON. SOLUTION: Clean PS308 and check for binding of the actuator. Solution ID TAUS0626886EN* Solution Usage 2
Description DF315, part numbers for the SCDB, RADF CB, the RADF harness. Solution PART NUMBER 13LK-9011 55YA-9050 13LK-8010 Solution ID
ITEM RADF CB SCDB RADF harness Solution Usage 1

TAUS0605389EN*

Description F52-02 prior to the completion of warm-up. Solution CAUSE: The conveyance suction fan (FM4) has failed or poor connection to the printer driver board (PRDB). SOLUTION: Check for binding components in the conveyance suction fan housing. To check FM4, perform the following: 1. Access the 47 multimode (power the machine OFF, then, while holding down on the 4 and 7 keys, power the machine ON), output code 42, P-03-P. 2. Check PRDB CN33-B9 (orange wire on the left side of the connector). This is the 24V DC power origination point for actuation of the conveyance suction fan. A reading of 24V DC should be measured when the fan is in the ON mode and 0V DC should be measured when the fan is in the OFF mode. 3. If 0V DC is measured with the conveyance suction fan in the ON mode, power the copier OFF (using sub power switch, SW2 and main power switch, SW1). 4. Remove CN33 from the PRDB. 5. Ensure that all the pins for CN33 on the PRDB are straight and properly aligned. Then inspect CN33 on the wiring harness. Ensure that all the wires are properly attached to the connector. 7. Reseat CN33 on the PRDB. 8. If 24V DC is measured for a second and then it goes to 0V, check the fan connector (CN57). If CN57 appears normal, then replace FM4. Note: The conveyance suction fan motor (p/n 55GA80510) has been changed to p/n 55YA80510. This change only affects the 7045 conveyance suction fan motor. Solution ID TAUS0613188EN* Solution Usage 1

Description Unable to enter correct copy quantity. Solution CAUSE: Copy limit function is enabled. SOLUTION: To program the copy quantity limit, perform the following: 1. Power the copier OFF. 2. Access the 25 mode (power the copier ON, while pressing the 2 and 5 keys). 3. Touch [1. Software SW] on the touchscreen. 4. Select dipswitch [9] using the left up-arrow on the touchscreen 5. Select the bit number of the switch using the middle up-arrow. 6. Select OFF (0) or ON (1) to program the desired setting. 7. Use the matrix below to input the desired copy quantity limit. 9-0 9-1 9-2 9-0 No limit Copy limit = 0 Copy limit = 0 Copy limit = 0 Copy limit = 0 Copy limit = 0 Copy limit = 0 Copy limit = 1 Copy limit = 1 Copy limit = 99 8. Power the copier OFF/ON to exit the 25 mode. Solution ID TAUS0616891EN* Solution Usage 1
Description How to program the scanning Mixed Original mode as default at power up when an IP431 is installed. Solution Scanning application functions are retained until the AUTO RESET button is pressed while in scanner mode, or sub switch (SW2) or main switch (SW2) is powered OFF/ON. Note: Job memory is only for copier mode functions. Solution ID TAUS0617255EN* Solution Usage 1
Description Can the machine run 80lb card stock? Solution The specifications are: Paper Weight 20lb-24lb bond recommended (Maximum range: 16lb-19lb, 25lb-32lb) Transparency film, Labels Solution ID TAUS0617930EN* Solution Usage 1
Description Intermittent F10-09 in idle. Solution CAUSE: On the operation board/1 assembly CN210 or CN211 is poorly seated. This results in communication failure with the main CB. SOLUTION: To check CN210 and CN211, perform the following: 1. Power the copier OFF. 2. Remove the operation unit (P/N 55YE-7000). 3. Remove CN210 from the operation board/1 assembly (p/n 55YA-9031). 4. Ensure that all the pins for CN210 on the operation board/1 assembly are straight and properly aligned. Then inspect CN210 on the wiring harness.
Ensure that all the wires are properly attached to the connector. 5. Reseat CN210 on the operation board/1 assembly. 6. Remove CN211 from the operation boasrd/1 assembly. 7. Ensure that all the pins for CN211 on the operation board/1 assembly are straight and properly aligned. Then inspect CN211 on the wiring harness. Ensure that all the wires are properly attached to the connector. 8. Reseat CN211 on the operation board/1 assembly. 9. Reinstall the operation unit. Solution ID TAUS0618018EN* Solution Usage 1

Description DF315, jam position 13 when using the mixed original mode only. Solution CAUSE: The tension spring for guide plate (B) (p/n 120A45542) is not properly tensioned, causing guide plate (B) to block the paper path during the paper reversal process. SOLUTION: To check the tension spring, perform the following: 1. Power the copier OFF. 2. Raise the open-close cover and remove the entire black guide assembly (p/n 120A-4692) from the RADF. 3. Thoroughly, inspect the position of guide plate (B), which should be positioned above the middle guide (p/n 120A45515). 4. Viewing the entire black guide assembly from the rear side, inspect the upper tension spring, which maintains guide plate (B) in the raised position. 5. Replace the tension spring (p/n 120A45560) as necessary. Solution ID TAUS0618024EN* Solution Usage 1
Description Conveyance suction fan motor FM4 part number change. Solution The conveyance suction fan motor FM4 (p/n 55GA80510) has been changed to p/n 55YA80510. Note: This change only affects the 7045 conveyance suction fan motor. Solution ID TAUS0618554EN* Solution Usage 1
Description How to program the cartridge set mode agitation time. Solution To program the cartridge set mode agitation time, perform the following: 1. Power the copier OFF. 2. Access the 25 mode (power the copier ON, while pressing the 2 and 5 keys). 3. Touch [1. Software SW] on the touchscreen. 4. Select dipswitch [22] using the left up-arrow on the touchscreen 5. Select the bit number [5] using the middle up-arrow. 6. Select OFF (0) or ON (1) to program the desired setting. 7. Use the matrix below to input the desired cartridge set mode agitation time. 22-5 set to 0: Four (4) minute agitation time 22-5 set to 1: Two (2) minute agitation time. 8. Power the copier OFF/ON to exit the 25 mode. Solution ID TAUS0618914EN* Solution Usage 1
Description Metric paper size is detected in the Universal tray and RADF (DF315). Solution CAUSE: Destination code is not programmed for inch size specifications. SOLUTION: Program the destination code by performing the following procedure: 1. Access 25 mode (power OFF/ON while holding 2 and 5 keys). 2. Select option 1 (SOFTWARE SW). 3. Scroll to dipswitch 5-0 and set to ON (1). 4. Scroll to dipswitch 5-1 and set to OFF (0). 5. Power machine OFF/ON.
Solution ID TAUS0619100EN* Solution Usage 1

Description How to enable copying from the platen glass when mixed original mode is defaulted ON. Solution To enable copying from the platen glass when mixed original mode is defaulted ON, perform the following: 1. Power the copier OFF. 2. Access the 25 mode (power the copier ON, while pressing the 2 and 5 keys). 3. Touch [1. Software SW] on the touchscreen. 4. Use the up/down arrows to scroll to software switch 11-0. 5. Touch [ON] on the touchscreen. 6. Power the copier OFF/ON to exit the 25 mode. Solution ID TAUS0622312EN* Solution Usage 1
Description PLEASE CLOSE FRONT DOOR MESSAGE at power up. Solution CAUSE: Failed MS1 (front door switch). SOLUTION: Replace MS1 (p/n 40AA85010). Solution ID Description F52-3 code Solution CAUSE: Failure of polygon cooling fan (FM6). SOLUTION: To check the cooling fan operation, perform the following: 1. Access the 47 multimode (power the machine OFF, hold down the 4 and 7 keys, and power the machine ON), output code 042, press 004. 2. Cycle the fan OFF/ON. It may be very erratic on the restarts. 3. Replace the polygon cooling fan FM6 (p/n 26NA80510) as needed. Solution ID TAUS0623169EN* Solution Usage 1 TAUS0622941EN* Solution Usage 1
Description DF315, THIS MODE IS UNAVAILABLE FOR THIS SIZE message when trying to copy 8.5x14 or 11x17 originals from the RADF. Solution CAUSE: On a machine with no finisher installed, rotation and sort have been selected as the output mode. SOLUTION: To cancel rotation and sort as the output mode, perform the following: 1. Press the [OUTPUT] key. 2. When the Select Output Screen is displayed [Rotation + Sort] will be highlighted. Touch [Rotation + Sort] which will cancel this choice. 3. Touch [OK] on the touchscreen. Solution ID TAUS0623449EN* Solution Usage 1
Description Equitrac* products such as PrintLog* Professional are unable to correctly track both print and copy volume. Solution CAUSE: Konica copiers/printers have software dipswitches that must be set properly to enable correct volume count. SOLUTION: The Network Transaction Station Connection PDF lists the connector pinout and the dipswitch settings for 7020 and 7075 series. Notes:
1. See also the Network Transaction Station Connection Revision A PDF. 2. To view the PDFs, Acrobat* Reader must be installed. Acrobat Reader can be downloaded for free from the Adobe* Web site at: [[http://www.adobe.com/products/acrobat/readstep2.html| URL http://www.adobe.com/products/acrobat/readstep2.html]] * Trademark ownership information Solution ID TAUS0625799EN* Solution Usage 1
Description How to copy/print onto envelopes, 7045. Solution Konica Minolta does not recommend copying/printing onto envelopes with the 7045, as it was not designed to run envelopes. Additionally, envelopes do not meet the standards set for paper specifications. The following special paper is recommended: Transparency film Labels Hole punch Rag content Note: These special papers must only be fed from the multi-sheet bypass tray. Solution ID TAUS0627274EN* Solution Usage 1

Description How to print the management list. Solution The management list is a 9-page document containing jam and failure lists; adjustment settings; parts lists and counters. To print the list: 1. Access the 36 mode (power the machine ON by operation panel switch while holding down the 3 and 6 keys). 2. Select [7: List Print]. 3. Select [4: Management List]. 4. Press the copy button on the touchscreen. 5. Select the paper size. 6. Press Start. 7. Power OFF/ON with the operation panel power switch to exit the 36 mode. Note: Save the print out for future reference. Solution ID TAUS0615737EN* Solution Usage 0
Description How to submit a file for a current installation or pre-sales printer test in a Microsoft* Windows or Macintosh* environment. Solution To submit a file for a current installation or pre-sales printer test in a Windows or Macintosh environment, perform the following: 1. Provide the product's current print driver to the customer. 2. Have the customer configure the job as they would like it printed and print the job to a file. This will eliminate the need for NSSG to have a copy of the specific application and will save time trying to determine how the document is supposed to be formatted for printing. Note: Most applications have a 'print to file' option. 3. Have a SRF (Service Request Form) filled out by contacting the NSSG Hotline. In NSSGs continuing review of support processes, the method of requesting advanced levels of support have been redefined. NSSG no longer requires that a SRF form be filled out by the technician and faxed. Instead, to streamline the process and reduce the process time, NSSG will now take all the information live on the phone at the Contact Center. Contact Center
Engineers are responsible for providing troubleshooting support. Most calls are resolved with only one call, but in the event that several calls have been made and the problem remains open, the Engineer will start the on-site support process by assisting the caller with the Support Request Form (SRF). SRFs are also used for Complex Installation Support, Application Support, Enhanced Application Support, Enterprise Print Consulting and Workshops. The Contact Center number is 800-825-5664. Use the assigned NSSG User ID for access and the Support Engineer will be happy to assist complete the SRF. * Trademark ownership information Solution ID TAUS0616246EN* Solution Usage 0
Description Test Synopsis to verify that Equitrac* PrintLog* Professional, version 4.0.19 accurately tracks print jobs and does not adversely affect print output when used in conjunction with the current Konica IP units and associated main bodies and print drivers. Solution Test Synopsis results. Note: To view the above link, Acrobat* Reader must be installed. Acrobat Reader can be downloaded for free from the Adobe* Web site at: [[http://www.adobe.com/products/acrobat/readstep2.html| URL http://www.adobe.com/products/acrobat/readstep2.html]] * Trademark ownership information Solution ID TAUS0616263EN* Solution Usage 0

Description Can NCR PAPER* be used as copy paper in the 7045? Solution Konica recommends an NCR PAPER named [[Xero/Form* II| URL http://www.appletonpapers.com/webapp/wcs/stores/servlet/sheetsxeroformiifeatures?currentCategory=149094&langId=-1&catalogId=239327&storeId=13932 7]] from a company called Appleton Papers in Wisconsin. Xero/Form II is a vegetable-based product that works extremely well. It is available through Xpedx paper distributors nationwide. * Trademark ownership information Solution ID TAUS0618140EN* Solution Usage 0
Description Intermittent scrambled image on copies. Solution CAUSE: Failed charge wire and/or charging control plate. SOLUTION: Replace charge wire (p/n 55FA25011) and charging control plate (p/n 55GA25070). Solution ID TAUS0618232EN* Solution Usage 0
Description Intermittent PLEASE OPEN LEFT SIDE COVER AND REMOVE PAPER message when duplexing. Solution CAUSE: The ADU paper feed loop timing is set too high or too low. SOLUTION: To adjust the paper feed loop timing for the ADU, perform the following: 1. Access the 36 mode (power the copier ON, while simultaneously pressing the 3 and 6 keys). 2. Press [2. Timing adj.].
3. Press [3.Paper loop adj.]. 4. Press [NEXT] (located in the lower left hand side of the touchscreen) 8 times or until [Paper loop adj. (ADU)] is displayed. 5. Make necessary adjustments. Setting ranges are from (-127 to +127). 6. Press [Return]. 7. Power OFF/ON. Note: J92-00 will increment in the management list. Solution ID Description Blank copies. Solution CAUSE: Shorted or damaged toner supply motor 1 (M10). SOLUTION: Remove toner supply motor 1 (p/n 55HE-3290) and inspect the output worm gear shaft for wobbling. If the output shaft of the motor wobbles, replace the motor assembly. SPECIAL NOTE: This solution provided by Jim Wood, KBT Orlando. Solution ID TAUS0619121EN* Solution Usage 0 TAUS0618557EN* Solution Usage 0
Description FS109, stapler cartridge lever (green release) part number. Solution The stapler cartridge lever (p/n 120H99010).

TAUS0620218EN*

Description FS109, stapler cartridge lever (green release) part number. Solution The stapler cartridge lever (p/n 120H99010) is not listed in the Parts Catalog.

TAUS0621738EN*

Description How to FTP print on the 7045. Solution The 7045/IP431/KN303 does not support FTP printing.

TAUS0622707EN*

Description When using Adobe* Acrobat* Pro version 6x, DG DAT MSG OUT OF EXPECTED SEQUENCE message while attempting to retrieve.tif files from the network scanner using the Konica Minolta TWAIN driver version 1.04. After this message, only the first page of a multiple page file is retrieved. Solution CAUSE: Early version Konica Minolta TWAIN network scanner driver is installed. SOLUTION: Use minimum version 1.11 Konica Minolta TWAIN driver (the latest version is recommended). The driver can be downloaded from the Konica Minolta FTP site or from the [[Konica Minolta website driver database| URL http://kmbs.konicaminolta.us/eprise/main/KMBS/Support_Center/Home]]. When installed, this driver will replace the currently installed TWAIN driver on the Microsoft* Windows workstation. Trademark ownership information Solution ID TAUS0622847EN* Solution Usage 0

Description Print jobs are stuck in the queue as the Microsoft* Windows server or workstation is waiting for machine status to change to ready (from the feedback condition of Add Paper - for example).
Solution CAUSE: SNMP status enabled on the print driver installed on the server. With this enabled the print queue constantly monitors SNMP printer feedback (door open, paper tray empty, etc.). The feedback from the machine may not be in real time resulting in locking the print queue on the server or workstation hosting the printer. SOLUTION: Disable SNMP status on the print driver. 1. From the printers folder, highlight the printer object, right click and select properties. 2. Select Ports 3. Configure Port. 4. Uncheck SNMP Status Enabled. * Trademark ownership information Solution ID TAUS0646835EN* Solution Usage 0
Description Does Konica Minolta provide support for Equitrac* products? Solution For Equitrac technical support information please visit [[http://www.metrics.com/Support/| URL http://www.metrics.com/Support/]] or contact trained Support Engineers by telephone at 519.885.2458, by fax at 519.746.7931 or via E-mail at support@metrics.com Note: Technical Support is available Monday through Friday, 8 AM to 6 PM, EST. *[[Trademark ownership information| FILE V:\\TEXT\\TRADEMRK.TXT NEW]] Solution ID TAUS0647780EN* Solution Usage 0
Description F51-4 at power up or at the start of the copy process. Solution CAUSE: The developing unit is binding, or M3 developer drive motor is damaged. SOLUTION: Inspect the developing unit (p/n 55GA-3003) for binding and replace if necessary. If developer is not binding any more, replace the M3 (p/n 55GA80030), and/or the PRDB (p/n 55HA-9064). Solution ID TAUS0652435EN* Solution Usage 0
Description DF315, J65-01 at power ON. Solution CAUSE: Original registration did not get detected at PS306. SOLUTION: Test PS306 in 47 mode, multimode P004P (do not press Start); the state should be OFF with cover closed; ON when RADF cover is opened. If no change, replace the sensor and sensor mylar: PS306 (p/n 129H85510), Sensor mylar (p/n 120A45021). Solution ID TAUS0652715EN* Solution Usage 0
Description How to store PCL* fonts onto the print system hard drive or compact flash card. Solution To store a PCL font onto the IP controller hard drive (or compact flash card) on legacy Konica models the following prerequisites are necessary: 1. The actual font or bar code must be purchased by the user. 2. The font must be a PCL font or can be a PCL Soft font. If it is a Soft font, the font must first be edited to make it a PCL font then it can be modified for storage on the IP unit. 3. The workstation used to edit the file must be equipped with DOS/Dos editor. Notes: a. Follow this step-by-step procedure for the complete installation procedures and for the proper parts ordering procedures. b. To view this PDF hyperlink, Acrobat* Reader must be installed. Acrobat Reader can be downloaded for free from the Adobe* Web site at: [[http://www.adobe.com/products/acrobat/readstep2.html| URL http://www.adobe.com/products/acrobat/readstep2.html]] * Trademark ownership information

Description Unable to install 32-bitdrivers on a Microsoft Windows 2003 64-bit server formigration to the 32-bit clients. Solution The 32-bit driver files are not recognized when attempting to load on a 64-bit system, therefore, the files must be pulled from a 32-bit system in order to add additional driver support on a 64-bit server: 1. After installing the 64-bit driver on the server, install the matching 32-bit(PCL, PostScript Visual, PostScript (Plug-in) or PostScript (Adobe) driveron one of the clients. 2. The driver files will be placed in C:\WINDOWS\inf folder on the client. 3. Share this folder on the network so that the 64-bit server has access. 4. From the server, when adding additional drivers, browse to the shared folder on the workstation 5. Select the appropriate.inf file from the shared folder on the client - the driver files will then be pulled over to the server to support other 32-bit clients when migrating the driver files. Note: It is important to install the same type of driver on the client to match the driver installed on the server.

TAUS0700244EN*

How to determine what version of Sun Java is installed on a Microsoft Windows workstation. Solution To determine what version of Sun Java is installed, perform the following: 1. From a command prompt type:java -version 2. Press Enter. 3. The version of Sun Java will be indicated. If the command is not recognized then Sun Java is not installed. Solution ID TAUS0701104EN* Solution Usage
Description F52-6 code at start up. Solution CAUSE: IP-431 CPU cooling fan has failed. SOLUTION: Replace the IP-431 CPU cooling fan (p/n 13LV80510). Solution ID TAUS0701561EN* Solution Usage
Description DF-315, F67-1 and J65-5 codes at start up. Solution CAUSE: Failed RADF sensors - PS306 (original registration) and PS309 (original reverse detect). SOLUTION: Replace both PS306 (p/n 129H85510) and PS309 (p/n 12OA85520). Solution ID TAUS0702146EN* Solution Usage
Description How to perform Print Screens (screen shots) from a Microsoft Windows OS and Macintosh OS. Solution Please see the attacheddocument for detailed information. Note : To view a PDF, Adobe Reader must be installed. Adobe Reader can be downloaded for free from the Adobe web site at: http://www.adobe.com/products/acrobat/readstep2.html Solution ID TAUS0702534EN* Solution Usage
Description How to install a printer using LPR (IP Printing) under Macintosh OS9. Solution Please perform the procedures mentioned in the attached document. Note : To view a PDF, Adobe Reader must be installed. Adobe Reader can be downloaded for free from the Adobe web site at: http://www.adobe.com/products/acrobat/readstep2.html