Description E47-01 shortly after power up. Solution CAUSE: Failed image processor board (IPB). SOLUTION: Replace the IPB (p/n 55WA-9500). Inspect and repair, as necessary, any pinched, damaged or loose connections to the IPB. Pay particular attention when connecting CN424 and CN425. Solution ID TAUS0613570EN* Solution Usage 9
Description Booklet mode with 8.5x11R originals and copy paper creates a booklet with the page sequence incorrect. Solution CAUSE: Sequential memory conflict when using the booklet mode and scanning originals in the 8.5x11R direction. SOLUTION: To create a booklet with the proper page sequence, perform the following: 1. Install the latest EPROMs (currently level 24.1). 2. Access the Key Operator Mode (power the copier ON, while pressing the HELP key). 3. Touch [9. Memory switch] on the touchscreen. 4. Touch the down-arrow located on the touchscreen six (6) times. [No. 23: Rotation] will be displayed in the dark blue band at the top of the touchscreen. 5. Repeatedly, touch [Change Setting Contents] until ON is displayed in the dark blue band at the top of the touchscreen. 6. Power the copier OFF/ON to exit the Key Operator Mode. 7. Press the [APPLICATION] key on the operation panel. 8. Touch [Booklet] on the touchscreen. 9. Touch [NO COVER SHEET], [COVER WITH COPY SHEET], or [COVER WITH BLANK SHEET] on the touchscreen. 10. Touch [OK] two (2) times to return to the normal copy mode. 11. Load the originals in the RADF in the 8.5x11 direction 12. Manually select the tray containing 8.5x11R paper by touching the display indication on the touchscreen. 13. Press the START/PRINT key to process the job. Solution ID TAUS0613803EN* Solution Usage 4

September 2007

Description Intermittent J17-5, while copying. Solution CAUSE: The movement of the lower paper exit guide (located in the reverse paper exit unit) is sluggish, due to a weak solenoid holder spring, or binding between the shaft of the lower paper exit guide and the bushings, resulting in improper sensor actuation. SOLUTION: To ensure proper movement of the lower paper exit guide, perform the following: 1. Power the copier OFF. 2. Remove the reverse paper exit unit. 3. Inspect the solenoid holder spring for any signs of damage or weakness. Increase the tension, or replace the spring (p/n 55TA43240) as necessary. 4. Remove the e-clips (p/n 00Z670406) from each end of the lower paper exit guide shaft. 5. Remove and clean the paper feed delivery shaft bushings. Replace the paper feed delivery shaft bushings (p/n 466076020) as necessary. 6. Thoroughly, clean the ends of the lower paper exit guide shaft. Replace the lower paper exit guide shaft (p/n 55TA43090) as necessary. Solution ID TAUS0614178EN* Solution Usage 4

Description Intermittent J72-19. Solution CAUSE: The spring is not properly installed on the stacker conveyance passage detection photosensor (PS5). SOLUTION: Ensure that the spring on the actuator of PS5 (p/n 12AR-4570) returns it to the home position. Solution ID TAUS0614498EN* Solution Usage 13
Description J17-5 intermittently from Tray 3. The paper feed timing is inconsistent. Solution CAUSE: The LCT conveyance clutch (CL3), located on the LCT-1000 Tray Paper Feed/Conveyance Section is dirty or has failed. SOLUTION: Remove the LCT-1000 Tray Paper Feed/Conveyance Section from the machine. Thoroughly, clean and inspect the LCT conveyance clutch. Replace the LCT conveyance clutch (p/n 55FA82330) as necessary. Note: Thoroughly, clean and inspect all bushings, bearings, gears, and drive shafts associated with any clutch prior to its replacement. Drive system binds can cause clutch slippage and produce symptoms simulating clutch failure, which may actually be resolved with installation of a new clutch. However, in such cases the symptom has been addressed rather than the underling cause of the clutch slippage. Solution ID TAUS0616212EN* Solution Usage 3
Description F36-1 at power up. Solution CAUSE: A prescribed temperature is not reached within 120 seconds from the start of warm up. The fuser lamps L2, L3, L4 do not come on due to an open circuit with TS1 or TS2. SOLUTION: Replace TS1 (p/n 25SA88420) or TS2 (p/n 25BA88470) as necessary. Solution ID TAUS0616448EN* Solution Usage 23
Description PLEASE WAIT WARMING UP displayed and will not clear. Solution CAUSE: Dmax adjustment will not complete due to lack of toner in hopper. SOLUTION: Add toner to the toner hopper and set the toner replenish stop function. To set the toner supply stop mode: 1. Enter the memory rewrite mode by turning the copier on while pressing the 2 and 5 keys. Release the 2 and 5 keys when the (25 Mode Menu Screen) appears. 2. Select [1] (Software switch setting). 3. From the (Software SW Setting Screen) use the arrows to select and change the following dip switches: a. 7-0 to 1 to enable the toner supply stop function. b. 7-1 to 1 to have the copier stop after the need for toner is detected and the number of copies set by 7-2 and 7-3 are completed. I. 7-2 and 7-3 to 0 for 100 copies. II. 7-2 to 1 and 7-3 to 0 for 1000 copies. III. 7-2 to 0 and 7-3 to 1 for 2000 copies.
IV. 7-2 and 7-3 to 1 for 3000 copies. Note: The recommended setting is for 100 copies. c. 7-1 to a 0 to have the copier stop immediately after the need for toner is detected and one copy is completed. Solution ID TAUS0617115EN* Solution Usage 2

Description Job Memory Recall will not function with ECM ON. Solution CAUSE: The Auto Reset key function is set to Full Auto. SOLUTION: Change the Auto Reset key function to Initial Setting by performing the following: 1. Power the machine ON while pressing the Help key. 2. Select [9. Memory Switch]. 3. Use the arrows on the screen to select [2. Auto Reset Key Function]. 4. Select [Change Setting Contents]. Full Auto will change to Initial Setting. 5. Power the machine OFF/ON. Solution ID Description No power. Solution CAUSE: The DCPS has failed. SOLUTION: To check the DCPS, perform the following: 1. With the main switch (SW1) ON, check for 115V AC at CN397-1 and CN397-2 on the DCPS. 2. If present, check for 24V DC at CN2-1 and CN2-2 and 5V DC at CN8-9 and CN8-10 on the DCPS. 3. If not present, power the machine OFF and remove all connectors from the DCPS except CN382, CN395, CN396, CN397, CN398, and CN8. 4. Then power the machine ON. 5. Check for 24V and 5V directly off of the DCPS at the pins previously checked. 6. If voltages are still not present, replace the DCPS (p/n 55FA84511). Note: Check ICP4 and ICP5 to see if they are open. If they are, the DCPS may have been damaged by a bind in the Tray 3 and Tray 4 up/down motor or related parts. Do not replace the DCPS if ICP4 and ICP5 are open, without first checking for binding, as this may cause the DCPS to fail again. Solution ID TAUS0624503EN* Solution Usage 3 TAUS0620704EN* Solution Usage 8
Description Abnormal noise during paper feeding and J17-05/J17-06 jams occur frequently when paper is fed from Tray 3 and Tray 4. Solution CAUSE: Noise occurs because there is not enough grease on the clutch shaft. Also, increased friction in the clutch causes a paper feed timing error that results in a paper jam indication. SOLUTION: See 7150/7055/7060/FORCE 60/7065/FORCE 65 Technical Bulletin #49 for details. Note: To view the PDF, Acrobat* Reader must be installed. Acrobat Reader can be downloaded for free from the Adobe* Web site at: [[http://www.adobe.com/products/acrobat/readstep2.html| URL http://www.adobe.com/products/acrobat/readstep2.html]] * Trademark ownership information Solution ID TAUS0626572EN* Solution Usage 2
Description J30-01 occurs when using the bypass. Solution CAUSE: Loop timing is not properly adjusted. SOLUTION: Adjust the loop timing for the bypass tray. To adjust the loop timing, perform the following: 1. Access the 36 mode (power the machine ON while holding down on the 3 and 6 keys). 2. Select [2. Timing Adjustment]. 3. Select [3. Paper Feed Loop Adjustment]. 4. Press the Next adjustment key and select bypass. 5. Enter a value from the numeric keypad, then touch the Set key. The input range is -20 (small), 00 (standard), +99 (large). Note: (1 step =0.1 msec)
Solution ID TAUS0627198EN* Solution Usage 2
Description Drum wrap or separation jam. Solution PROBABLE CAUSES: 1. The separation claw is not contacting the drum. Inspect the operation of the separation claw (p/n 55FA-2030). Ensure the separation claw is not contacting the toner control sensor PCB (p/n 25SA-9100). If claw is contacting board, the rocking shaft (p/n 25SA20531 may be bent , the shaft can be straightened or replaced, it should have 1MM of clearance between the claws and the TCB. 2. Insufficient DC separation current data. Confirm DC separation data in the 36 mode, item #1 High Voltage Auto Adjustment, #5 DC Separation Adjustment. This data value should be above 100 when you are experiencing separation jams. Before changing the data, document original data in safe place for reference. Then set to 100, 105, 110, or 115 until best results are achieved. 3. Check the resistance of the drum grounding from the coupling to the frame ground, The value should be 1 ohm, not 7 - 8 ohms. Check for excessive amounts of grease from the drum shaft holder front and rear (p/n 25SA75010). Clean the excess grease from this area and again measure for resistance. If the value is still up to 3 ohms. A new ground strap to the front bearing may be needed, use (p/n 25SA15280) it may need to be straightened for this uses. Note: This earth spring is a ground for the cleaning blade and the toner hold plate. It conducts via the shaft PS material (p/n 25SA20460) this a conductive/plastic material. 4. The second paper feed front mylar is incorrectly positioned on the top plate instead of the lower plate. Reposition the mylar on the lower plate. Solution ID TAUS0656768EN* Solution Usage 22

Description FS106, all copies exit into the sub-tray when sort mode is selected. Solution CAUSE: Software dipswitches 2-0 and/or 2-1 are set to a 1. SOLUTION: To program software switch 2-0 and 2-1 to a 0, perform the following: 1. Access to 25 mode (hold down 2 and 5 at power ON). 2. Select [1] Software SW setting. 3. Press the left up arrow once to display software switch [2-0:* **]. 4. Press OFF to set software switch 2-0 to a 0 [2-0:0 00]. 5. Press the right up arrow once to display software switch [2-1:* **]. 6. Press OFF to set software switch 2-1 to a 0 [2-1: 0 00]. 7. Power copier OFF/ON to return back to normal copy mode. Notes: 1. Software switch 2-0 and 2-1 are FS106 service check switches and are not to be used for normal copy functions. 2. Set software switch 14-1 to a 1 if sub-tray exit is desired for non-sort mode. Solution ID TAUS0601125EN* Solution Usage 11
Description Is tandem printing/copying available? Solution A Tandem copy kit (Item # 950-792) is available for the 7055. This kit contains the required EPROMs to enable simultaneous tandem printing and copying. This kit is the same for the 7065, it contains a set of EPROMs for each model. Notes: 1. J17-5 jamming issues, and IP lock-up, have been associated with EPROM levels below 15.2. If any of these issues appear, Konica recommends installing level 15.2 EPROMs (or above). 2. Latest EPROM level and [[Internal Link for Faxing/Printing current 7055 EPROM information.| RUN V:\text\Wordpad.exe v:\text\newrom\7055.txt]] Solution ID TAUS0614189EN* Solution Usage 10
Description PU108, can the Punch Unit be used with the 7055? Solution The PU108 is compatible (in copy mode) with either the FS106, FS108 standard finisher, or the FS108B booklet maker finisher as long at the main body and finisher have the latest level EPROMs installed. Note: Availability of PU108 for 7055 and 7065 Info Source Bulletin No. 46-01. To view the PDF, Acrobat* Reader must be installed. Acrobat Reader can be downloaded for free from the Adobe* Web site at: [[http://www.adobe.com/products/acrobat/readstep2.html| URL
http://www.adobe.com/products/acrobat/readstep2.html]] * Trademark ownership information Solution ID TAUS0614297EN* Solution Usage 8
Description When copying 8.5x11 originals onto 8.5x11R in booklet mode, the image is not centered in the front-to-rear direction. Solution CAUSE: The reduction process of the 7055 always references the image to the rear of the machine. When booklet mode is selected, AMS reduces the copy to a standard 65% image, which results in a one-inch void area on the bottom of the page. SOLUTION: To produce a booklet mode copy, which fills the entire page in the front-to-rear direction, perform the following: 1. Load the 8.5x11 originals face up on the RADF unit. 2. Press the [APPLICATION] key. 3. Touch [BOOKLET] on the touchscreen. 4. Touch [NO COVER SHEET], [COVER WITH COPY SHEET], or [COVER WITH BLANK SHEET] as required. 5. Touch [OK] on the touchscreen two times. 6. Select the tray which has 8.5x11R paper loaded by touching its icon on the touchscreen. 7. Select the copy mode [1:2] or [2:2] by touching its icon on the touchscreen. 8. Touch [ZOOM] on the touchscreen. 9. Touch [VERTICAL] on the touchscreen. Using the numeric keypad on the touchscreen, enter a vertical magnification of 78%. 10. Touch [HORIZONTAL] on the touchscreen. Using the numeric keypad on the touchscreen, enter a horizontal magnification of 64%. 11. Touch [OK] on the touchscreen. 12. Press the START/PRINT key. Note: The vertical and horizontal magnification ratios, which were programmed in steps 9 and 10 can be varied depending upon the application and originals being used. Solution ID TAUS0613058EN* Solution Usage 7

Description Copier cycles OFF/ON continuously at power up. Solution CAUSE: Multiple board failure consisting of a failed operation panel and main CB. SOLUTION: Replace both the main CB (p/n 55TA-9019) and the operation unit (p/n 55WE-7000). SPECIAL NOTE: Solution provided by Roy Eagan, KBT Professional Services. Solution ID TAUS0622450EN* Solution Usage 4
Description F34-1 shortly after warm-up. Solution CAUSE: Failed DCPS board. The upper fuser roller heat lamp (L2) is not shutting OFF after copier has reached warm-up. SOLUTION: To confirm, verify L2 operation in diagnostics (power ON the copier while holding down the 4 and 7 keys). DO NOT press any output code. The
fuser unit heat lamps (L2, L3 or L4) should NOT be lit. If any of the lamps are ON, replace the DCPS board (p/n 55FA84512). Solution ID TAUS0643401EN* Solution Usage 4
Description PU108, J72-16 as paper enters the punch unit. The punch unit main motor never energizes. Solution CAUSE: The punch unit CB has failed. SOLUTION: To check the operation of the finisher main motor (M1), perform the following: 1. Access the 47 mode (power the copier ON while pressing the 4 and 7 keys), output code 75, P-72-P to energize the punch unit main motor. 2. If, the motor energizes in the 47 test mode, but fails to energize in the copy mode, the punch unit CB has failed. Replace the punch unit CB (p/n 13NK-9010) as necessary. Solution ID TAUS0611548EN* Solution Usage 3
Description What controllers can be used with the 7055? Solution The IP303 and IP304 can be used with the 7055.

TAUS0613362EN*

Description How to select the bypass tray for covers in the booklet mode. Solution This feature is not currently available. This machine defaults to tray 1, for covers, when the cover selection is made in the booklet mode. The User's Reference Guide indicates to load cover paper in tray 1. Solution ID TAUS0613599EN* Solution Usage 3
Description FS106, finisher is not recognized by the copier. Solution CAUSE: The interface connector (CN119), located on the rear exit side of the copier has a damaged pin, resulting in a communication failure between the finisher and main body. SOLUTION: To check the interface connector (CN119), perform the following: 1. Power the copier OFF. 2. Remove CN161, of the finisher from the main body interface connector (CN119). 3. Thoroughly, inspect all pins within the interface connector (CN119). Ensure that none of the pins are bent or broken. Replace the DC wiring harness (p/n 55TA90050) as necessary. Solution ID TAUS0613762EN* Solution Usage 3
Description How to reset the drum counter. Solution To reset the drum counter, perform the following: 1. Power the copier OFF. 2. Access the 47 mode (power the copier ON, while pressing the 4 and 7 keys), output code 091. 3. Press the START/PRINT key. 4. Power the copier OFF/ON to return to normal mode. Note: To verify drum count reset, Press P, 3 and then START/PRINT. The top of the touchscreen will display the current drum count, which should be 0. Solution ID TAUS0613940EN* Solution Usage 3

Description The touch panel is blank with a blue background. Solution CAUSE: Failed operation unit PCB1. SOLUTION: Replace the operation unit (p/n 55WE-9020). Solution ID Description TAUS0615012EN* Solution Usage 2
Image compressed from front-to-rear. Solution CAUSE: An image processing board from a model 7065 was installed. SOLUTION: Install a model 7055 image processing board (p/n 55WA-9500). Solution ID TAUS0615217EN* Solution Usage 2
Description F47-06 during process. Solution CAUSE: Communication failure from the E-RDH to the IMPB. SOLUTION: Replace the E-RDH board (p/n 55FA-9620). Solution ID TAUS0615350EN* Solution Usage 2
Description When configured as a printer, with ECM enabled, all print jobs stored to the print queue while an operator is using the machine in copier mode are printed at the completion of the copy job and counted against the password of the current operator using the machine. Solution CAUSE: The count pulses to C(K) during printer mode is enabled, causing the printer page count to be added to the total page count of the current password enabled operator of the machine. SOLUTION: To disable the count pulses to C(K) during printer mode, perform the following: 1. Power the copier OFF. 2. Access the 25 mode (power the copier ON, while pressing the 2 and 5 Keys). 3. Touch [1. Software switch setting] on the touchscreen. 4. Select software dipswitch 18-4 using the arrow keys. 5. Set the switch to ON (1). 6. Power the copier OFF/ON to exit the 25 mode. Solution ID TAUS0615571EN* Solution Usage 2
Description How to adjust the trailing edge void area. Solution To adjust the trailing edge void area, perform the following: 1. Power the copier OFF. 2. Access the 25 mode (power the copier ON, while pressing the 2 and 5 keys). 3. Touch [1. Software switch setting] on the touchscreen. 4. Select software dipswitch #17 using the left up/down arrow. 5. Select the bit number of the switch using the middle up-arrow. 6. Select OFF (0) or ON (1) to program the desired setting. 7. Use the matrix below to input the desired trailing edge void area. 17-2 17-0 Does not 2mm 3mm 5mm 8. Power the copier OFF/ON to exit the 25 mode. Solution ID TAUS0615593EN* Solution Usage 2
Description When making multiple copies off the glass, the paper exits face up, causing the copies to be out of order. Solution CAUSE: The default operation is to exit originals face up. SOLUTION: To allow copies to exit face down in the subtray, perform the following: 1. Press the OUTPUT MODE button. 2. Select SUBTRAY and then FACE DOWN. 3. Select OK.

Description White lines/streaks from front-to-rear when copying photos in the Non-image Area Erase mode. Solution CAUSE: The light reflected from the photo's glossy finish is adversely affecting the operation of Non-image Area Erase. SOLUTION: In the 25 mode, set software switch 8-0 to a 0, by performing the following: 1. Turn the machine OFF. 2. Enter the 25 mode, (turn the machine ON, while pressing the 2 and 5 keys). 3. Select 1: Software Switch Setting. 4. Use the arrows on the LCD to select dipswitch 8-0. 5. Touch the OFF key on the LCD to change the data to 0. 6. Press PREVIOUS SCREEN. 7. Power the machine OFF/ON to exit the 25 mode. Notes: 1. This symptom will also occur when Auto layout is selected because Auto layout automatically selects Non-image Area Erase. 2. For more information with Non-image Area Erase settings, refer to the 7055 Service Manual (7/2000) page 3-10. Solution ID TAUS0613739EN* Solution Usage 1
Description PRINT IN PROGRESS message will not clear when trying to print test pages from the operation panel of the main body. The 7055 is connected to an IP303. Solution CAUSE: The image processing board has failed. SOLUTION: Replace the image processing board (p/n 55WA-9500). Note: The IP303 connects directly to the image processing board. A separate video interface board is not used on the 7055. Solution ID TAUS0613764EN* Solution Usage 1
Description Black line in lead-to-trail direction. Solution CAUSE: Miscommunication with the image processing board.
SOLUTION: Reseat all the connectors on the image processing board. If the problem persist, replace the image processing board (p/n 55WA-9500). Solution ID TAUS0613863EN* Solution Usage 1
Description What sorting or grouping modes are available without a finisher installed? Solution The 7055 is available with the following 3 output modes when configured without a finisher: Sort with normal exit (default), an output mode is not selected, all pages will exit in sets. Sort with alternate exit. Group with normal exit. Notes: 1. Sort with alternate exit requires that 8.5x11 and 8.5x11R paper be loaded in any tray except bypass tray. 2. Refer to page 6-28 and 6-29 of the 7055 User's Manual. 3. The offsetting of copies does not occur in any of the 3 output modes. Solution ID TAUS0613930EN* Solution Usage 1
Description E41-2 when scanning from the platen glass. Solution CAUSE: Pinched wire was not passing the PLL signal from the optics motor drive board (OPMDB) to the main CB. SOLUTION: Reseat CN224 on OPMDB and CN223 on the main CB. If problem persists, clip the tie wraps off the wiring harness. Verify operation. Solution ID TAUS0614037EN* Solution Usage 1

Description F22-1 at power up. Solution CAUSE: The charge corona wire cleaning mechanism is jammed. SOLUTION: Remove the charge corona and ensure that the wire cleaning mechanism moves freely. Solution ID TAUS0619353EN* Solution Usage 1
Description PU108, unable to perform the staple and punch functions within the same job. Solution CAUSE: The punch unit destination setting is programmed for four (4) holes Europe default, resulting in a logic conflict. SOLUTION: To properly program the PU108 destination, perform the following: 1. Power the copier OFF. 2. Access the 25 mode (power the copier ON, while pressing the 4 and 7 keys). 3. Touch [1. Software switch setting] on the touchscreen. 4. Select software switch #7 using the left up/down arrow. 5. Select the bit number of the switch using the middle up/down arrow. 6. Select OFF (0) or ON (1) to program the desired setting. 7. Use the matrix below to input the proper destination. 7-4 7-5 MODE PU-108/for 2 holes (Default for Japan) PU-108/for 3 holes (Default for North America) PU-108/for 4 holes (Default for Europe) 8. Power the copier OFF/ON to exit the 25 mode. SPECIAL NOTE: Solution provided by Ramon Tappan, (OCALA), E.G.P. INC. Solution ID TAUS0619445EN* Solution Usage 1
Description PLEASE SELECT ORIGINAL OR SELECT SCAN SIZE message is displayed when copying from the platen. Solution CAUSE: The Platen original size detection AB/inch, is set to Both AB & inch in the 25 mode. This needs to be set to Destination series only. SOLUTION: To set the machine to Platen original size AB/inch to Destination only perform the following: 1. Access the 25 mode (power the copier OFF/ON, while simultaneously pressing the 2 and the 5 key). 2. Select [1. software switch settings]. 3. Using the far left down arrow on the touchsreen scroll to DIP SW 16. 4. Using the middle up arrow on the touchscreen scroll to BIT 0. 5. On the far right of the touchscreen select [OFF]. 6. Power the copier OFF/ON.
Solution ID TAUS0619467EN* Solution Usage 1
Description Number of reserve jobs which can be programmed while the output job is printing. Solution The machine has a total job setting capacity of 2 (output job and reserve job). Therefore, while the output job is printing you can store 1 job into reserve.

TAUS0619523EN*

Description F28-1 after completing a PM. Solution CAUSE: This code indicates an abnormality with the charging output, which can be the result of maintenance procedures performed on the charging corona unit. SOLUTION: To check the charging corona unit, perform the following: 1. Power the copier OFF. 2. Remove the charging corona unit and check for proper positioning of the corona wire and charging control plate grid. 3. Replace the charge wire (p/n 55FA25012) or charging control plate grid (p/n 25SA25081) as necessary. Solution ID TAUS0619705EN* Solution Usage 1

Description FS108B, paper exiting extremely slow causing a J72-17. Solution CAUSE: The shaft holding part of the slide pulley has worn. As a result, the timing belt becomes slack, skipping teeth, and slows down the paper exit operation. SOLUTION: Replace the slide pulley (p/n 129U76550). Notes: 1. As a preventative measure, apply a couple of drops of grease (p/n 00GR00190) in the groove for lubrication. The grease application is recommended at every 1,000,000 copies. 2. To view the PDF hyperlinks, Acrobat* Reader must be installed. Acrobat Reader can be downloaded for free from the Adobe* Web site at: [[http://www.adobe.com/products/acrobat/readstep2.html| URL http://www.adobe.com/products/acrobat/readstep2.html]] * Trademark ownership information
Solution ID TAUS0624250EN* Solution Usage 1
Description PU108, not being recognized. Solution CAUSE: The connectors are not properly seated on the PUCB (punch unit control board). SOLUTION: Reseat all connectors on the PUCB. Solution ID TAUS0625862EN* Solution Usage 1
Description E46-12 only when copying in the 2:2 mode. Solution CAUSE: One or both of the RADF feed clutches are dirty or have failed. SOLUTION: The RADF feed clutches are not designed for disassembly and cleaning. It is recommended to replace both clutches (CL301) (p/n 120A82010) and (CL302) (p/n 120A82020). Solution ID TAUS0627241EN* Solution Usage 1
Description FS108B, part number for lower rear stapler slide blocks. Solution Lower rear stapler slide blocks (p/n 129U42440).

TAUS0627247EN*

Description FS108, part number for lower rear stapler slide blocks. Solution Lower rear stapler slide blocks (p/n 129U42440).

TAUS0627332EN*

Description FS108B, J73-10 occurs during copy mode. Solution CAUSE: The actuator for PS25 (p/n 540085510) failed. SOLUTION: Increase the tension on the spring (p/n 540041103) for the actuator (p/n 25SA41201) of PS25. Solution ID TAUS0627500EN* Solution Usage 1
Description FS108, is the FS108B finisher CB compatible with the FS108? Solution The FS108B finisher CB is not compatible with the FS108. FS108B CB (p/n 129X-9016) FS108 CB (p/n 129U-9018) Solution ID TAUS0628423EN* Solution Usage 1
Description E03 occurs at power up. Solution CAUSE: The DCPS failed.
SOLUTION: Replace the DCPS (p/n 55FA84512). Solution ID TAUS0629168EN* Solution Usage 1
Description PLEASE CHECK ORIGINAL OR SELECT THE SCANNING AREA is displayed when an 8.5x11 original is placed on the platen glass. Solution CAUSE: Improper programming of the platen original size detection AB/inch dipswitch. SOLUTION: To properly program the platen original size detection AB/inch dipswitch setting, perform the following: 1. Access the 25 mode. 2. Scroll to dipswitch 16-0. 3. Touch [OFF] on the touchscreen to set dipswitch to [0]. 4. Power the copier OFF/ON to exit the 25 mode. Solution ID TAUS0629760EN* Solution Usage 1

Description PU108, casters no longer installed during production. Solution Newer production punch units no longer have casters mounted. Since the casters serve no purpose once the unit is installed, they are no longer being installed during production. Although the service manual and parts catalog still show the casters, the parts center will not fill any orders for these items. Solution ID TAUS0614922EN* Solution Usage 0
Description User's Manual, 7055. Solution 7055 User's Manual Note: To view the PDF, Acrobat* Reader must be installed. Acrobat Reader can be downloaded for free from the Adobe* Web site at: [[http://www.adobe.com/products/acrobat/readstep2.html| URL http://www.adobe.com/products/acrobat/readstep2.html]] * Trademark ownership information Solution ID TAUS0615094EN* Solution Usage 0
Description FS108B, J72-28 Solution CAUSE: The finisher bypass gate solenoid (SD5) is not properly adjusted. SOLUTION: Perform the bypass gate adjustment as outlined on pages 1-70 and 1-71 of the FS-108/FS108BM service manual. After adjustment, ensure the solenoid and gate move freely with no binding. Solution ID TAUS0616248EN* Solution Usage 0
Description Test Synopsis to verify that Equitrac* PrintLog* Professional, version 4.0.19 accurately tracks print jobs and does not adversely affect print output when used in conjunction with the current Konica IP units and associated main bodies and print drivers. Solution Test Synopsis results. Note: To view the above link, Acrobat* Reader must be installed. Acrobat Reader can be downloaded for free from the Adobe* Web site at: [[http://www.adobe.com/products/acrobat/readstep2.html| URL http://www.adobe.com/products/acrobat/readstep2.html]] * Trademark ownership information Solution ID TAUS0616268EN* Solution Usage 0
Description Test Synopsis for Create!form*, Create!form Server and Create!print* printing sample forms/data and a custom form/data from Microsoft* Windows 98, Windows 2000 Professional, Windows NT 4.0 Workstation using Windows NT 4.0 Server as the Create!form Server. Solution Test Synopsis results. Note: To view the above link, Acrobat* Reader must be installed. Acrobat Reader can be downloaded for free from the Adobe* Web site at: [[http://www.adobe.com/products/acrobat/readstep2.html| URL http://www.adobe.com/products/acrobat/readstep2.html]] * Trademark ownership information Solution ID TAUS0616301EN* Solution Usage 0
Description FS108B, intermittent F77-25 when folding.
Solution CAUSE: Cracks in blade cams. SOLUTION: Replace the [[blade driving cam assembly kit (p/n SE95-3940)|URL http://techweb.konicabt.com/tpm/media/m20020622a1.pdf]]. Notes: 1. Individual parts are NOT available for the Motor MT plate/B (p/n 129X48280), ONLY available in the Kit. Machines with serial number 129Y03871 and above have the new style Motor MT plate/B installed from factory. 2. To view the PDF, Acrobat* Reader must be installed. Acrobat Reader can be downloaded for free from the Adobe* Web site at: [[http://www.adobe.com/products/acrobat/readstep2.html| URL http://www.adobe.com/products/acrobat/readstep2.html]] * Trademark ownership information Solution ID TAUS0616309EN* Solution Usage 0

Description Modification to make performing the flat stapling position adjustment easier. Solution See FS108B Technical Bulletin #5 for details. Note: To view the PDF, Acrobat* Reader must be installed. Acrobat Reader can be downloaded for free from the Adobe* Web site at: [[http://www.adobe.com/products/acrobat/readstep2.html| URL http://www.adobe.com/products/acrobat/readstep2.html]] * Trademark ownership information Solution ID TAUS0623973EN* Solution Usage 0
Description Microsoft* Windows 2003 Server PCL* printer driver support. Solution Currently, there is no Konica PCL driver available for Microsoft Windows 2003 Server printing via the 7055/IP303. * Trademark ownership information Solution ID TAUS0624332EN* Solution Usage 0
Description Site requirements, 7055. Solution Site Requirements 20 and 30 Ampere Machines. See also Konica Minolta Site Requirements Forms ( FO-9 and FO-10 ) which provide the site requirements to which customers must conform before having any Konica Minolta 20 or 30 ampere models installed. Note: To view the above PDFs, Acrobat* Reader must be installed. Acrobat Reader can be downloaded for free from the Adobe* Web site at: [[http://www.adobe.com/products/acrobat/readstep2.html| URL http://www.adobe.com/products/acrobat/readstep2.html]] * Trademark ownership information Solution ID TAUS0624628EN* Solution Usage 0
Description FS106, main exit tray caution label. Solution See Safety Bulletin #66 for details. Note: To view the PDF, Acrobat* Reader must be installed. Acrobat Reader can be downloaded for free from the Adobe* Web site at: [[http://www.adobe.com/products/acrobat/readstep2.html| URL http://www.adobe.com/products/acrobat/readstep2.html]] * Trademark ownership information Solution ID TAUS0624632EN* Solution Usage 0
Description FS108B, main exit tray caution label. Solution See Safety Bulletin #66 for details. Note: To view the PDF, Acrobat* Reader must be installed. Acrobat Reader can be downloaded for free from the Adobe* Web site at: [[http://www.adobe.com/products/acrobat/readstep2.html| URL http://www.adobe.com/products/acrobat/readstep2.html]] * Trademark ownership information Solution ID TAUS0625826EN* Solution Usage 0
Description TU108, SC77-37 during operation and unable to select fold/staple and trimmer. Solution CAUSE: M106 (FNS driving motor) timing belt fell off. SOLUTION: Re-install the timing belt. Solution ID TAUS0625832EN* Solution Usage 0
Description FS108/108B Service Manual. Solution FS108/108B Service Manual. Note: To view the PDF, Acrobat* Reader must be installed. Acrobat Reader can be downloaded for free from the Adobe* Web site at: [[http://www.adobe.com/products/acrobat/readstep2.html| URL http://www.adobe.com/products/acrobat/readstep2.html]] * Trademark ownership information Solution ID TAUS0626608EN* Solution Usage 0
Description After setting the desired value for density shift (Text/Photo), the value changes back to its original value after the machine has been turned OFF/ON. Solution CAUSE: The desired value was not entered correctly. SOLUTION: To correctly enter the value, perform the following: 1. Power the copier ON. 2. Press the P key. 3. Press the 5 key. 4. Press the START/PRINT key. 5. Using the numeric keypad, enter the desired density shift (0-5). 6. Press the START/PRINT key to complete the setting. 7. Press the STOP/CLEAR key to return to the normal mode. Solution ID TAUS0627277EN* Solution Usage 0

Description What print drivers are compatible with Macintosh OS X (Version 10)? Solution The latestprint driversare available via the Konica Minolta Download Selector. Access the Selector from the the KMBS public site ( http://www.kmbs.konicaminolta.us ), Support & Drivers tab or from SSDWeb Support (CS Expert Support) by clicking on 'Download MSDS, Drivers, Firmware and more'. Macintosh OS 9x applications within OS 10.2.x are supported using the current Adobe PostScript drivers for Macintosh at http://www.adobe.com/support/downloads/product.jsp?product=44&platform=Macintosh. Solution ID TAUS0609312EN* Solution Usage
Description E46-25 shortly after power up. Solution PROBABLE CAUSES: 1. L1 (exposure lamp) emitting low light. Check operation of L1 in 47 mode (hold down the the 4 and 7 while powering ON the machine), output code 000, press START and reply to LCD window choice YES/NO. Replace L1 (p/n 55TA83010) if it does not light. 2. The slit glass, which holds the white reference sheet in place, has become dislodged. To check the slit glass and white reference sheet, perform the following: a. Power the copier OFF. b. Remove the right platen guide (p/n 55TA12511), platen stopper plate rear (p/n 55TA12521), platen glass (p/n 55GA61501), and the white color base plate assembly (p/n 55TA-6930). c. Ensure that the white reference sheet and slit glass are properly installed. If either of the parts are damaged, replace the white color base plate assembly (p/n 55TA-6390). 3. The 2A 250V fuse on the Lamp Starting Board failed. Replace the 2A 250V fuse on the Lamp Starting Board (p/n 55TA83510). Note : There is not a part number listed in the parts manual for the fuse. The fusecan be purchased locally. 4. Failed DCPS. To test the DCPS, check the following: a. L1 is ON in diagnostics. b. The value in 47 mode, output code 97 reads all sevens with max as 255 and min as 119. c. Fuse on the INVB is reading 24V DC on both legs. d. On the DCPS, check for 5V DC on CN400-6, -5V DC on CN400-8, and 12V DC on CN400-5. If any of these voltages are not present, replace the DCPS (p/n 55FA84512). Solution ID TAUS0634060EN* Solution Usage
Description List of equipment that is no longer being supported. Solution Please see attached Product & Technical Support Bulletins 1792 and 2443 andMarketing Bulletin#07-GB-016. Note : To view a PDF, Adobe Reader must be installed. Adobe Reader can be downloaded for free from the Adobe web site at: http://www.adobe.com/products/acrobat/readstep2.html

TAUS0702146EN*

Description How to perform Print Screens (screen shots) from a Microsoft Windows OS and Macintosh OS. Solution Please see the attacheddocument for detailed information. Note : To view a PDF, Adobe Reader must be installed. Adobe Reader can be downloaded for free from the Adobe web site at: http://www.adobe.com/products/acrobat/readstep2.html Solution ID TAUS0702534EN* Solution Usage
Description How to install a printer using LPR (IP Printing) under Macintosh OS9. Solution Please perform the procedures mentioned in the attached document. Note : To view a PDF, Adobe Reader must be installed. Adobe Reader can be downloaded for free from the Adobe web site at: http://www.adobe.com/products/acrobat/readstep2.html

MATERIAL SAFETY DATA SHEET

Page:1/5

MSDS No.: 028002302 Products Name: DRUM (PHOTOCONDUCTOR) 7050/7050M/7060/7150/7065/7055/7170 Prepared Date:1-Dec-1997 Revised Date: 5-Feb-2009
1. PRODUCT AND COMPANY IDENTIFICATION
Product Name: DRUM (PHOTOCONDUCTOR) 7050/7050M/7060/7150/7065/7055/7170 used for: 7050/7050M/7060/7150/7065/7055/7170 Supplier Identification: Konica Minolta Business Solutions (Canada), Ltd. 369 Britannia Road East Mississauga, Ontario L4Z 2H5 Telephone: (905)890-6600 Facsimile: (905)283-2511 Emergency Telephone No. CHEMTREC Telephone: 1-800-424-9300 WHMIS: Not a controlled product (manufactured article)
COMPOSITION / INFORMATION
Major Ingredients: [Generic Name] Substrate Aluminium drum Coating layer Polycarbonate OPC compound Organic pigment +++: Suppliers confidential information Hazardous Ingredients: None present

INGREDIENTS

[CAS No.] 7429-90-5 1-10 +++ +++ +++ [%] > 90

Page:2/5

3. HAZARDS IDENTIFICATION
Emergency Overview: Green Cylinder Almost odorless Classification: Not classified as dangerous. (1999/45/EC) Most Important Hazards and Effects of the Products For Human Health: No symptoms expected with intended use. For the Environment: No data are available on the adverse effects of this product on the environment. For Others: None Specific Hazards: None

FIRST-AID

MEASURES
No symptoms expected with intended use. None
Symptoms of Overexposure: Routes of Entry: Information Inhalation: Skin Contact: Eye Contact: Ingestion: Note to Physician: None
No treatment is required. No treatment is required. No treatment is required. No treatment is required.

FIRE-FIGHTING

CO2, water, foam and dry chemical None None This material has no unusual fireor explosive hazards. No special equipment is required.
Suitable Extinguishing Media: Extinguishing Media to Avoid: Special Firefighting Procedures: Fire and Explosion Hazards: Protection of Firefighters:

ACCIDENTAL

RELEASE
Not applicable with intended use. Not applicable with intended use. Not applicable with intended use.
Personal Precautions: Environmental Precautions: Methods for Cleaning Up:

HANDLING

STORAGE
Handling Technical Measures: None Precautions: This product will be scorched in the case of fire. Safe Handling Advice: None. Storage Technical Measures: Storage Conditions: Incompatible Products: Packing Materials:
None Keep and Store in a cool and dry place. None None

Page:3/5

8. EXPOSURE CONTROLS / PERSONAL PROTECTION
Engineering Measures Ventilation: None required with intended use. Control Parameters OSHA-PEL(USA): DFG-MAK(EC):
Not Applicable Not Applicable
ACGIH-TLV(USA): Worksafe-TWA(Austl):
Personal Protective Equipment None required when used as intended in Konica Minolta equipment. Hygiene Measures: Wash hands after handling.

PHYSICAL

CHEMICAL

PROPERTIES

Form: Cylinder Color: Green
Appearance Physical State: Solid Odor: Almost odorless
<<Results of the coated compounds on the aluminum substrate.>> Boiling Point: Not applicable Melting/Softening Point: No data available Flash Point: Not applicable pH: Explosion Properties: Not applicable Density(g/cm): 1.2 Solubility in water: insoluble Flammability: Not applicable Oxidizing Properties: No data available Ignition Temperature(C): No data available Vapor Pressure: Not applicable Partition Coefficient, n-Octanol/Water: Not applicable (*= Based on data for other Konica Minolta Products with similar ingredients)

STABILITY

REACTIVITY
Stability: Stable [ X ] Unstable [ Hazardous Reactions: None Conditions to avoid: None Materials to Avoid: None Hazardous Decomposition Products: CO, CO2

Page:4/5

11. TOXICOLOGICAL INFORMATION
Health Effects from Exposure: No symptoms expected with intended use. Toxicological Data <<Result of the coated compounds on the aluminum substrate.>> Acute Toxicity: Inhalation, LC50(mg/l): Not applicable Ingestion(oral), LD50(mg/kg): >5000 (rat) Dermal, LD50(mg/kg): Not applicable Eye irritation: No data available Skin irritation: Non irritant (Rabbit) Skin sensitizer: No data available Mutagenicity: Negative (AMES test) Local Effects: No data available Chronic Toxicity or Long Term Toxicity: None Carcinogenicity IARC Monographs: Not listed NTP(USA): Not listed OSHA Regulated(USA): Not listed

12. 13.

ECOLOGICAL DISPOSAL

INFORMATION

No data available

CONSIDERATION

Appropriate Methods of Disposal Waste may be disposed or incinerated under conditions which meet all federal, state and local environmental regulations.

TRANSPORT

Special Precautions: None Information on Code and Classifications According to International Regulations UN Classification: None

Page:5/5

15. REGULATORY INFORMATION
US Information Information on the label: Not required SARA(Superfund Amendments and Reauthorization Act) Title III 302 Extreme Hazardous Substance: None 311/312 Hazard Categories: None 313 Reportable Ingredients: None California Proposition 65: This product contains no chemical substances subject to California Proposition 65. EU Information Information on the label(1999/45/EC and 67/548/EEC): Symbol & Indication: Not required R-Phrase: Not required S-Phrase: Not required Article14 (2.1) of Directive 1999/45/EC is not applicable to this product.
NFPA Hazard Rating: The National Fire Protection Agency(USA): Health: 0 Flammability: 1 Reactivity: 0 HMIS RATING: The National Paint and Coating Association(USA): Health: 0 Flammability: 1 Reactivity: 0 Recommended Uses: Photoconductor for Electrophotographic Equipment Restrictions: The above information is believed to be accurate and represents the best information currently available to Our Corporation. However, Our Corporation makes no warranty with respect to such information, and Our Corporation assumes no liability resulting from its use. Users should make their own investigation to determine the suitability of the information for their particular purposes. Literature References: ANSI Z400.1-1993 ISO 11014-1 Commission Directive 91/155/EEC