Featuring

Workgroup Document System
Transforming Digital Office Workflow

Polymerized Toner

The Konica 7135 combines functionality with productivity for todays demanding workgroup environments. Designed to be modular, this 35 page-per-minute digital MFP provides copy, print, scan and fax functionality all in one compact footprint. Built around Konicas proven engine design, the new 7135 delivers more consistent, higher quality output than other devices in its class with Konicas breakthrough Simitri Polymerized Toner, which maintains the uniformity of the toner particles to produce clean, crisp 600 x 600 dpi resolution with an offset-like look. Fully networkable, the 7135 features Scan Once, Print Many technology and an intuitive, user-friendly and interactive touch screen for easy access to all advanced features including scan-to-e-mail, scan-to-hard drive and scan-to-FTP functions. Additional versatility is achieved with a three-way standard paper supply along with two optional drawer bases to allow for a maximum online capacity of 2,550 sheets. The optional IP-423 print controller, optional 2 GB hard drive, standard PCL5e/6 emulation and innovative IP Connexion Web Utilities also provide added convenience by enabling users to configure the multifunctional capabilities to meet their needs. The Konica 7135. designed to meet even the most varied office requirements.

7135 Highlights

35 ppm Printing / Copying 600 x 600 dpi Resolution
Standard 64 MB Print Controller Memory IP-423 Print Controller with Standard Network Interface Card Optional Dual Fax Line Up to 2,550-Sheet Paper Capacity Stamp, Wa t e rmark, Image Overlay, Reserv e Copy Job and 5 Copy Memory
Polymerized Toner Technology w
32 MB Standard, 288 MB Maximum Copier Memory Optional 2 GB Hard Drive (Required for Scanning)

Features

Integrated Printing, Copying, Faxing, and Scanning:
A fully networkable 4-in-1 MFP, the 7135 delivers functionality and productivity in one of the easiest to set up and configure packages available today.
KONICA 7135 SPECIFICAT I O N S
Configuration Speed Warm Up Time / First Copy Out Time Resolution Standard Memory / Maximum Memory Reduction / Enlargement Continuous Copying Original Paper Size - Minimum / Maximum Average Monthly Duty Cycle / Maximum PM Cycle Paper Handling Standard Input Capacity Paper Size - Minimum / Maximum Paper Weights - Minimum / Maximum Drawer Base Options DB-210 DB-410 Paper Capacity - Maximum Automatic Duplex Finisher Options Total Finisher Capacity Standard 2 Tray (FS-107) 3 Tray Option (FT-107) 4 Tray Option (FT-107) Console 35 cpm (8.5 x 11); 15 cpm (11 x 17) 30 Seconds or Less / 4.2 Seconds 600 x 600 dpi 32 MB / 288 MB 25% - 400% 1-999 5.5 x 8.5 / 11 x 17 6,000 - 12,000 Pages / 100,000 Pages 100,000 Pages 2 x 500 Sheets (Universal), Multi Bypass - 50 Sheets 5.5 x 8.5 / 11 x 17 16-32 lbs. 2 x 500 Sheets (Universal) 1 x 1500 Sheets (8.5 x 11) 2,550 Sheets Standard / Stackless 1,100 Sheets 100 + 1,000 = 1,100 Sheets 100 + 100 + 600 = 800 Sheets 100 x 4 = 400 Sheets FEATURES
A Wide Range of Finishing Capabilities:
The 7135 offers two enhanced finishing options for a wide range of workgroup or department needs: The IT-101 Internal Tray offers modes for non-sort, rotation sort, group mode and rotation group mode. The FS-107 Finisher provides even more options for increased effectiveness initially equipped with two trays, it can be expanded with up to two additional trays for modes including non-sort, sort, staple sort or group sort.

Enhanced Functionality:

The capability to scan-to-e-mail, scan-to-hard drive and scan-to-FTP comes standard with the IP-423 print controller, which features a 300 MHz processor, 192 MB maximum memory and optional 2 GB hard drive (required for scanning). The new FK-102 Fax Kit delivers more with the added benefits of a total of 40 one-touch keys, standard JBIG compression for added speed and a dual-line option.
Job Memory, OHP Interleave, Image Shift, Frame/Fold Erasure, ECM, APS, AMS, ATS, Book Copy, Stamp/Watermark

Polymerized Toner:

Breakthrough Simitri Polymerized Toner Technology provides significantly better halftone definition and better solid fills. By maintaining toner particle uniformity, Simitri toner produces more consistent output than traditional methods, achieving clean, crisp 600 x 600 dpi resolution with an offset-like look.

Modular Design:

This truly multifunctional system is designed to grow as your document production needs grow. Optional expanded memory, large capacity drawer bases, document feeder, print controller and fax kit allow for easy customization to meet current and future needs.

Innovative Web Utility:

New, more graphical IP Connexion Web Utility 2.0 provides instant information about the machines configuration, from paper and accessories to network settings, from any browser.
PRINTER SPECIFICATIONS Optional IP-423 PCL Print Controller w/ Standard Network Card, Scan-to-Email, Scan to FTP, Scan-toHard Drive ( 2GB Hard Drive Required for Scanning) Speed 35 pages-per-minute Resolution 600 x 600 dpi Memory 64 MB / 192 MB DIMM Network Card 10/100 BaseT Print Drivers Windows 95, 98, ME, NT 4.0, 2000, XP Options 2.0 GB HDD (HD-107), Adobe PS 3 Kit (PS-345) FAX SPECIFICATIONS Type 33.6 Kbps Super G3 Compatibility ITU Group 3 with ECM Compression MH, MR, MMR, JBIG Memory - Standard 2 MB / 16 MB One-Touch / Group / Total Keys 40 / 40 / 200 Options Internet Fax (IF-102)*, Dual Line (FL-102) WEIGHT, YIELDS, ELECTRICAL REQUIREMENTS, DIMENSIONS Machine Weight 158.7 lbs. Drum / Developer Yields 200,000 / 200,000 Impressions Toner Yield 30,000 Impressions Electrical Requirements 120V, 60Hz Dimensions 2.8 W x 23.4 D x 32.1 HI Type
All specifications are approximate and are subject to change. All names are trademarks or registered trademarks of their respective companies. *Available 1st Qtr 2003
KONICA BUSINESS TECHNOLOGIES, INC.
www.konicabt.com KBT-02-41
2002 Konica Business Technologies, Inc.

Printed in U.S.A.

Output Mode for Machine without Finisher.. 3-31 Output Mode for Machine with Finisher.. 3-34 Output Mode for Machine with IT-101... 3-38 Checking Feature Selections and Proof Copying.. 3-41 Interrupt Copying.... 3-44
Section 4: Job Memory & Help Mode
Storing Job Conditions (Job Memory: Job Store).. 4-2 Recalling Stored Job Settings (Job Memory: Job Recall).. 4-6 Displaying Screen for Operation Guide (Help Mode).. 4-8
To Display Help Screen from Basic Screen.. 4-8 To Display Help Screen from Other Screens... 4-10 ii
Section 5: Troubleshooting
When Call for Service Message is Displayed... 5-2
Limited Use of the Copier in Trouble... 5-3
Preventive Maintenance... 5-4 Clearing Mishandled Paper... 5-5 When JAM Appears on Folder Key... 5-7 When ADD PAPER Appears on Folder Key... 5-9 When Memory Full Message Is Displayed (Memory Overflow).. 5-10
Action 1..... 5-10 Action 2..... 5-11
When Power OFF/ON Screen Is Displayed.. 5-12 Troubleshooting Tips.... 5-13
Section 6: Machine Specifications
Main Body Specifications... 6-2 Option Specifications... 6-5

Advanced

Section 7: Advanced Information
Programmed Shut-Off (Weekly Timer)... 7-2 Rotation.... 7-4 Vertical/Horizontal Zoom Mode... 7-6

Section 8: Applications

To Display Application Selection Screen... 8-2 Inserting Sheets and Covers (Sheet/Cover Insertion).. 8-3 Positioning Title Pages on the Right Side (Chapter).. 8-8 Lay Out Several Pages onto One Sheet (Combination). 8-11 Making a Multiple Page Signature Booklet (Booklet).. 8-14 Copying onto Transparency Films (Transparency).. 8-17 Inserting Images into Printed Sets (Image Insert).. 8-20 Dividing an Image into Right and Left Pages (Book Copy). 8-23 Copying Mixed Size Originals (Mixed Original).. 8-28 Copying Folded Original (Folded Original)... 8-31 Copying Non-Standard Size Originals (Non-Standard Size).. 8-34 Reverse the Second Side in 1-2 Mode (Upside Down). 8-36 Making Copy Quality Closer to Originals (Text/Photo Enhance).. 8-39 Reversing Color in Black and White Image (Reverse Image).. 8-42 Repeating Selected Image Area (Repeat: Vert./Horiz. Mode). 8-44 Repeating Automatically or Selecting Repeating Times (Repeat: AUTO/ Repeat Mode).. 8-47 Eliminating Black Copy Marks Along Borders (Frame/Fold Erasure). 8-51 Copying Image in the Center of Copy Paper (AUTO Layout).. 8-54 Adjusting Position of Copy Image (Image Shift).. 8-57 Reducing Images to Create Binding Margin (Reduce&Shift).. 8-60 Erasing Outside of the Original (Non-Image Area Erase).. 8-63 Printing Stamp, Page, Watermark onto Copies (Stamp).. 8-66 Overlaying an Image onto Each Page Copied in the Job (Overlay). 8-71

Unit: inches (mm) 9.9 (252) 21.7 (550) 22.8 (580) 19.7 (500) 7.9 (200)

32.1 (815) 44.4 (1127)

10.6 (269)

26.1 (662) 38.3 (974)

52.4 (1332)
52.9 (1345) Main body + DF-314 + IT-101 + DB-410
Unit: inches (mm) 21.7 (550) 19.7 (500) 60.0 26.1 (1524) (662) 10.6 (269) 38.3 (974) 7.9 (200)

17.7 (450)

22.8 (580)

44.4 (1127) 32.1 (815)

60.2 (1530)
Main body + DF-314 + DB-210 + FS-107 + FT-107
Precautions for Routine Handling

WARNING: High Voltage

DO NOT TOUCH the high voltage parts indicated with WARNING label or described in the manual.
CAUTION: Actions in Response to Troubles
If the Service Call screen is displayed and copier operations cannot be continued, stop the operation to prevent any unexpected accident. Write down the report code (stated on the 2nd line of the message), then switch off the copier and disconnect from the power socket. Contact your service representative and inform them of the report code. Do not touch high temperature parts indicated with CAUTION labels or described in the manual. Do not touch the inside of the machine for any purpose other than removing jammed paper or adding toner. If machine repair is necessary, be sure to contact your service representative. Never attempt to repair it by yourself. If any abnormal sound, smell or smoke comes from the machine, immediately stop using it, turn off the power switch, disconnect the power plug and contact your service representative. If the breaker trips or the fuse blows, turn off the power switch, reset the breaker or the fuse, and turn on the machine. If the same situation occurs again, contact your service representative. Ensure the replacement fuse conforms with the rating of the power source. Never use a fuse with an incorrect rating.
Do not use volatile combustibles, such as thinner or alcohol, near the machine.
CAUTION: Prohibition of Machine Modification
Do not modify or remove any parts by yourself.
CAUTION:Prevention of Machine Troubles
Do not drop small metallic objects, such as paper clips or staples, inside the machine. Do not place any heavy or hard objects such as a vase, books or ornaments on the machine.
CAUTION: Recommendation of Periodic Check

For details of the ECM setting, see p. 11-18 to p. 11-26.

Enter ECM password.

Enter your 8-digit ECM password, using the keypad.
For setting an ECM password, see p. 11-20 to p. 11-21.
If an invalid ECM password is entered, continue by entering the correct password.

Press [START].

Your current copy count and copy limit will be displayed for 3 sec.
Current count / limit 018888/025000

Start a copying job.

When the message changes to Ready to copy, copying job is available on the machine.
When your copy count reaches the copy limit, the message Copy limit reached will be displayed. In that case, contact the Key Operator to reset your copy limit.
Press [] while pressing [#].
The initial state will be restored, with the message Enter E.C.M. password displayed on the screen.
A paper indicator is shown on each tray key of the Basic Screen to indicate the paper level of the tray. (Four levels are provided: ) When paper in a tray becomes empty, the indicator appears on the tray key.
Follow the procedure below to insert paper in the empty tray. DETAILS
When the Multi-sheet bypass tray is empty, will be displayed on the bypass tray key instead of the copy size indication.
The Key Operator can set the machine to indicate the paper type for each tray selected on the screen. For details, see p. 11-28.
Loading Paper in Main Body Trays and DB-210 Trays
Main body trays: Tray 1 and 2 DB-210 trays: Tray 3 and 4
Withdraw the main body tray or DB-210 tray.
See p. 2-2 to check positions of each tray.
Do not withdraw the tray forcibly; otherwise you may be injured.
Loading Paper (continued)
Stack paper with curl side up.
Load paper, aligning it to the right side of the tray.

Rear guide plate

Size indication dial
Do not load paper above the red line on the side guide plates. Be sure that the rear guide plate is correctly positioned according to the paper size loaded; otherwise machine trouble may occur.
While pressing the release knob, move the side guide plate against the paper.
Release the release knob to lock the slide guide plate.
Do not change the paper size indication of the size indication dial at the front of the tray. Copying using a tray with a different size indicated may cause a paper misfeed.
Push in the tray until it locks into place.
The indicator on the tray key will change from
Loading Paper in DB-410 Tray

DB-410 tray: Tray 3

Withdraw the DB-410 tray.
Load paper, aligning it to the right side of the tray. The tray bottom will lower due to the stacker paper weight.
Do not load paper above the hooks on the side guide plates. Be sure that the rear guide plate is correctly positioned according to the paper size to be loaded; otherwise machine trouble may occur.

Positioning Originals

Positioning Originals in RADF
The document feeder (RADF) automatically feeds up to 50 originals directly to the platen area, starting with the top sheet. The RADF should only be used for unstapled, smooth, flat originals.
Positioning originals in Normal mode
Arrange originals in order.
Before placing originals in the tray, be sure the document feeder is fully close. Once closed, do not open the document feeder, otherwise selected copy conditions may be automatically altered. Be sure not to use unsuitable RADF originals. See p. 9-6 for details.
Position original(s) FACE UP in the document feeder tray.
Place two-sided originals with page one FACE UP. Up to 50 originals can be set at a time.
Do not set more than 50 originals or set originals over the red line indicated on the paper guides; otherwise a paper misfeed will occur. If the number of originals exceeds 50, divide them into blocks not exceeding 50 sheets, then load them from the block with the first page. See p. 3-24 to p. 3-26.

Adjust paper guides.

Positioning Originals (continued)
Positioning originals in Mixed original mode Mixed size originals can be copied together from the document feeder.
To use the Mixed original mode, see procedure on p. 8-28 to p. 8-30.
Arrange the mixed size originals as illustrated below.

To the depth To the left

Setting direction
Before placing originals in the tray, be sure the document feeder is fully close. Once closed, do not open the document feeder, otherwise the selected copy conditions may be altered automatically. Be sure not to use unsuitable RADF originals. See p. 9-6 for details.
See p. 9-7 for allowable combinations of mixed originals.
Position mixed originals FACE UP, aligned with the left rear side of the document feeder tray.
Positioning originals in Folded original mode Folded original mode detects the folded original size without using the size detection sensor of the RADF. HINT
To use the Folded original mode, see procedure on p. 8-31 to p. 8-33.
Arrange originals in order. Position original(s) FACE UP in the document feeder tray.
Positioning Original on Platen Glass
Use the platen glass when originals are not suitable for use with the document feeder, e.g., when size is incompatible, or when originals are folded, stapled, torn, or in otherwise poor condition.

Interrupt Copying (continued)
In Reserve mode, pressing [INTERRUPT] before the copier finishes scanning the reserve job originals clears the settings selected for the reserve job. For details of Reserve mode, see p. 3-27 to p. 3-28.
Set copy conditions, as desired.
The initial settings in Interrupt mode are as follows. Copy Mode RADF AES Lens Mode APS Print Quantity Finisher : 1a1 : ON : ON : 1.00 (100%) : ON :1 : Exit Tray 1 in Sort mode
Remove any document from the platen glass or from the document feeder, if present.
Press [START] to start the interrupt copying.
When [CHECK] is pressed during Interrupt copying, the information displayed reflects the initial copy job settings. Check mode will not display Interrupt copy job information.
When Interrupt copying is completed, press [INTERRUPT] again.
The [INTERRUPT] LED turns out and the INTERRUPT indicator on the Basic Screen returns to the SETTING indicator. The settings of the initial job will be restored on the Basic Screen.
Press [START] to resume copying. CAUTION
When the finisher / paper exit / inner tray capacity is exceeded due to the print quantity selected, remove the copied sets as they exit; otherwise, mishandled paper will occur. 3-45
For particular jobs in progress, copying will cease only after certain phases of the immediate operation are completed, as indicated by the [INTERRUPT] LED conditions described below. Collectively printing image stored in memory The LED blinks until one set of the current job is printed. Then the LED remains steady for the temporary job performed in Interrupt mode. Scanning originals into memory The LED blinks until scanning is completed for all originals placed in the document feeder. Then, the LED remains steady for the temporary job performed in Interrupt mode. Scanning originals into memory while printing in Reserve mode The LED blinks until the copier completes the current printing job, scans all originals placed on the document feeder, and prints one set of the Reserved job. The LED remains steady for the temporary job performed in Interrupt mode.
Job Memory & Help Mode
How to Use Helpful Functions

Job Memory

Storing Job Conditions (Job Memory: Job Store).4-2 Recalling Stored Job Settings (Job Memory: Job Recall).4-6 Displaying Screen for Operation Guide (Help Mode)..4-8

Paper Weight
Main Body Safety Standard Radio Interference Options
Machine Weight 158.7 lb (72 kg) +34.6 lb (15.7 kg) w/DK-109 +57.3 lb (26 kg) w/DB-210 +54.0 lb (24.5 kg) w/DB-410 +20.9 lb (9.5 kg) w/RADF +28.7 lb (13 kg) w/Finisher (FS-107) +7.9 lb (3.6 kg) w/Inner tray (IT-101) Main Body (with RADF) Width: 22.8 in. (580 mm) Depth: 23.4 in. (595 mm) Height: 32.1 in. (815 mm) Document Feeder (RADF) Width: 22.4 in. (570 mm) Depth: 18.9 in. (480 mm) Height: 3.9 in. (100 mm) Max. open angle: Stapler-Finisher (FS-107) Inside main body Width: 17.0 in. (432 mm) Depth: 18.2 in. (463 mm) Height: 10.0 in. (255 mm) Outside main body Width: 10.8 in. (275 mm) Depth: 19.6 in. (497 mm) Height: 15.4 in. (392 mm) Inner Tray (IT-101) Width: 16.9/22.9* in. (430/582* mm) Depth: 17.7 in. (449 mm) Height: 15.4 in. (392 mm)
*: When the tray is extended.

Machine Dimensions

Drawer Base Unit (DB-210/410) Width: 22.8 in. (580 mm) Depth: 23.4 in. (590 mm) Height: 12.0 in. (304 mm) Desk (DK-109) Width: 22.8 in. (580 mm) Depth: 23.4 in. (590 mm) Height: 12.0 in. (304 mm)

Option Specifications

Stapling Finisher (FS-107) Power source: Main body Exit tray: w/one FT-w/two FT-107 For exit tray capacity, see p. 9-3 to p. 9-4. Power source: Main body Exit tray: 2 Capacity: Exit tray 1; 50 sheets max. Exit tray 2; 100 sheets max. 5000 staples/cartridge

Inner Tray (IT-101)

Staple Cartridge
How to Use Advanced Functions
Programmed Shut-Off (Weekly Timer)..7-2 Rotation....7-4 Vertical/Horizontal Zoom Mode...7-6
Weekly Timer Rotation Vertical/Horizontal Zoom
Programmed Shut-Off (Weekly Timer)
The Weekly Timer function turns a copier on and off at the time specified by the Key Operator. This function is not factory-set. When a copier is under control of the Weekly Timer function, the Timer Interrupt mode message will be displayed after pressing the power switch, and copying is unavailable. However, copying can be available by using the following procedure.

Press the power switch.

Refer to the table below to select the desired Combination mode.
Layout Original Portrait type 2 in 1 Horizontal order 4 in in 1 Vertical order 4 in in 1

Landscape type 2 4

Making a Multiple Page Signature Booklet (Booklet)
Use the Booklet to make a multiple page signature booklet on both sides of paper from any tray. Original images are scanned into memory and automatically arranged in booklet format in correct order. >>>Specifications for Booklet<<<
Use RADF. Original pages should be a multiple of 4 in 1-2 mode or a multiple of 2 in 2-2 mode; otherwise blank pages are automatically inserted to the last. AMS is automatically selected. Select the desired paper size. Original Size: 8.5x11, 5.5x8.5 (16 ~ 32 lb). Incompatible Conditions: APS, 1a1, 2a1, Staple, Group, Rotation Sort, Rotation Group, Sheet/Cover Insertion, Combination, Transparency, Special Original (Mixed Original, Non-Standard Size, Upside Down), Repeat, Fold Erasure, AUTO Layout, Non-Image Area Erase, Stamp (Page, Numbering)

1-sided originals

. 47 48

Booklet copying

2-sided originals
Making a Multiple Page Signature Booklet (Booklet) (continued)
Touch Booklet on the Application Selection Screen.
The Booklet Mode Selection Screen will be displayed.
Touch to highlight the desired Booklet mode key.
Book Copy Mixed Original Folded Original Non-Standard Size Upside Down Text/Photo Enhance

4. 5. 6. 7.

The Application Selection Screen will be restored. Select additional Applications, as desired.
Select the 1a2 or 2a2 copy mode and the desired paper size.
AMS is selected automatically. To release AMS, select the desired magnification, then select paper size.

AUTO Layout

Frame/Fold Erasure
Image Shift Reduce & Shift Non-Image Area Erase Stamp
Original pages should be a multiple of 4 in 1-2 mode or a multiple of 2 in 22 mode; otherwise blank pages are automatically inserted to the last.
Copying onto Transparent Films (Transparency)
Use the Transparency function in 1a1 or 2a1 mode to copy onto overhead projection transparent films, and output a blank or copied interleaf sheet with each copied transparent film. In the Blank sheet interleaving mode, a blank interleaf sheet is output with each transparent film to keep the film material from sticking together. In the Copy sheet interleaving mode, a copied interleaf sheet is output with each transparent film to provide reference during a presentation, a version for photocopying, and a set for filing or inserting into a binder. >>>Specifications for Transparency<<<
Transparent film source: Multi-sheet bypass tray Print quantity: 1 Finisher cannot be used. AMS is automatically selected. Incompatible Conditions: APS, 1a2, 2a2, Sort, Staple, Group, Rotation Sort, Rotation Group, Sheet/Cover Insertion, Chapter, Booklet, Image Insert, Special Original (Mixed Original), Repeat

The subsequent screen for selecting binding type will be displayed.
Touch the desired binding type key.
Touch OK to restore the Special Original Screen.

5. 6. 7. 8. 9.

Touch OK on the Special Original Screen to return to the Application Selection Screen. Touch OK to return to the Basic Screen. Select additional copying features, as desired. Enter the desired print quantity from the control panel keypad.
When selecting 2-1 Upside down mode, use RADF to scan originals.
See p. 3-2 to p. 3-6 for details on positioning originals. Use RADF store mode (p. 3-24 to p. 3-26) when the original count exceeds 50.
Making Copy Quality Closer to Originals (Text/Photo Enhance)
Use this function to enhance the reproducibility of half tones so that the copy quality more closely matches to that of the original. Text Mode Use the Text mode when copying a text original. In this mode, text is improved in comparison to using the general mode. Photo Mode Use the Photo mode to reproduce a half-tone photo image. The copy will closely represent the half-tones of the original image. Increase Contrast Mode Select Increase Contrast to darken lightly printed images (e.g., pencil) without changing background exposure. In cases where the image is light and background is dark, the background will not be changed. DETAILS
In each enhance mode, the copy density level can be shifted three levels darker or three levels lighter (Density Shift) by the Key Operator setting. See p. 11-49 if this setting is desired.
>>>Specifications for Text/Photo Enhance<<<
Incompatible Copying Conditions: None

Auto mode

Photo mode
Applications Original Auto mode Increase contrast mode

Text mode

Making Copy Quality Closer to Originals (Text/Photo Enhance) (continued)
Touch Text/Photo Enhance on the Application Selection Screen.
The Text/Photo Enhance Screen will be displayed.
Touch TEXT, PHOTO, or INCREASE CONTRAST, as required.
Touch OK to return to the Application Selection Screen.

5. 6. 7. 8.

Touch OK to return to the Basic Screen. Select additional copying features, as desired. Enter the desired print quantity from the control panel keypad.
Reversing Color in Black and White Image (Reverse Image)
Use Reverse image to reverse the image from black-on-white to white-on-black, and vice versa. This is convenient for copying white-on-black originals and reversing them to fax. >>>Specifications for Reverse Image<<<
Incompatible Conditions: AUTO Layout, Non-Image Area Erase

Reverse Image copying

Incompatible Conditions: Group (with NUMBERING), Rotation Group (with NUMBERING), Book Copy, Special Original (Mixed Original, Non-Standard Size), Reverse Image, Repeat, AUTO Layout, Image Shift, Non-Image Area Erase
00/10/10 10:30AM DATE/TIME
L-Bottom C-Bottom R-Bottom

2/5 PAGE

002 / 005 NUMBERING

WATERMARK

Printing positions
Printing Stamp, Page, Watermark onto Copies (Stamp) (continued)
Touch STAMP on the Application Selection Screen.
The Stamp Menu Screen will be displayed.

Touch ORIGI. DIRECT.

The Original Direction Screen will be displayed.
Book Copy Mixed Original Folded Original Non-Standard Size Upside Down Text/Photo Enhance Reverse Image
Touch the key to match the originals to be copied, then touch OK to return to the Stamp Menu Screen.
Touch to select the desired key.
The subsequent screen will be displayed to allow you to specify the selected stamp type.
When selecting WATERMARK: Specify the watermark type and pages to print on.
Touch to highlight the desired watermark key on the screen. Touch Only first page to print the selected watermark on the first page only.
When selecting STAMP: Specify the stamp type, printing position, and pages to print on.
Touch to highlight the desired stamp type key on the screen. Touch POSITION to select the desired stamp position. See p. 8-70 for details. Touch Only first page to print the selected stamp on the first page only.
When selecting DATE/TIME: Specify the date/time type, printing position, and pages to print on.
Touch to highlight the desired date and time keys on the screen. Touch POSITION to select the desired stamp position. See p. 8-70 for details. Touch Only first page to print the selected stamp on the first page only.
When selecting PAGE: Specify the PAGE type and printing position.
Touch to highlight the desired page type key on the screen. Touch POSITION to select the desired stamp position. See p. 8-70 for details.

Original weight: 13 ~ 34 lb Max. feeder capacity: 50 sheets (20 lb paper) Curling tolerance: 10mm or less Original placement: Face up (see p. 3-3 for details.) DETAILS
See below for the guide width of each combination.
Paper & Original Info Guide width 8.5"x11" 11"x17" Guide width 5.5"x 8.5"x 8.5" 11" 8.5"x14"
Folded Original mode Use Folded Original mode to scan folded originals without using the size detection sensor of the RADF. See p. 8-31 to p. 8-33 for details.
Detectable original size:11"x17", 8.5"x14", 8.5"x11", 8.5"x11"R, 5.5"x8.5", 5.5"x8.5"R, A4 (297mm x 432mm ~ 140mm x 216mm) Original weight: 13 ~ 34 lb (no special stock) Max. feeder capacity: 50 sheets (20 lb paper) Curling tolerance: 10mm or less Original placement: Face up; orientation same as copy paper
How to Maintain the Copier
Adding Toner....10-2 Inserting a New Staple Cartridge into FS-107 Finisher.10-5 Cleaning Image Scanning Section...10-9 Cleaning Image Printing Section...10-12 Checking Copy Count...10-14 Service, Repairs, Supplies..10-15
Adding Toner Inserting New Staple Cartridge Cleaning Scanning Section Cleaning Printning Section Checking Copy Count Service, Repairs, Supplies

Adding Toner

When toner supply is low, the message Please add toner and the icon ( on the touch screen. Reminder!
Use the same number toner bottle as described on the label on the upper left side of the toner bottle cover. Otherwise, machine trouble may occur.

) display

Add toner according to the procedure as follows.
Loosen toner by tapping both top and bottom of the new toner bottle on a solid surface at least five times, then shake the bottle at least five times.
Open the machine front door, then unlock and open the toner bottle cover.

Adding Toner (continued)

Withdraw the toner bottle, then turn it clockwise to position the Up arrow mark at the top.
Fully withdraw the toner bottle straight toward the front to remove the bottle.

If the hooks cannot be released easily, open the conveyance unit cover 6 to perform the following steps. In this case, use care not to touch the drum inside the conveyance unit cover 6, and quickly perform the cleaning procedure to close the cover as soon as possible; otherwise the drum may be damaged by a long period of exposure.
Cleaning Image Printing Section (continued)
Push and slide the transfer/separator wire cleaning lever to the left and right, several times.
Move the lever to the right until it stops, then close the front cover. Close the right side door of the main body.

Checking Copy Count

This function allows you to view the current indication of the following items as a list on the touch panel: Total counter, Counter start date, FAX TX/RX counter (machine with the fax kit installed), Printer counter (machine with the IP kit installed), Scanner counter (machine provided with Scanner function), PM counter, Drum counter, Development counter, and Fixing unit counter. Check the count, then print it from the Counter List Screen, if desired.
Press [ (COUNTER)] on the control panel.
SCANNER / PRINTER HELP FAX COP
The Counter List Screen will be displayed. To display to the PM Counter Screen, press [CHECK]. Touching the Up arrow key on the PM Counter Screen will resume the Counter List Screen.
Counter List Screen PM Counter Screen
Touch PRINT, if desired, or touch OK to return to the Basic Screen.
Maintenance, Repairs, Supplies
Service Enter the name and telephone number of your Konica service representative, plus the machine serial number in the space provided below: ______________________________________________________ (Service Representative) ______________________________________________________ (Tel. No.) ______________________________________________________ (Machine Serial No.) Repairs When calling for repairs, be sure to have all necessary information at hand, such as the machine serial number and your own telephone number. If copy quality is the concern, bring a sample copy with you to the phone so that it can be described to your service representative.
Enter the telephone number for Repairs in the space provided below:
______________________________________________________ (Repairs Tel. No.) Supplies Be sure to use only supplies recommended by Konica Business Technologies, Inc. To maintain your supply inventory, check your supplies at regular intervals, and order supply items before they are depleted or even nearly depleted.
Enter the telephone number for ordering supplies in the space provided below.
______________________________________________________ (Supplies Tel. No.)
The PCUA number for the Drum used in the 7022/7130/7135 copier is: 950253. No other Drum has been approved for use in this model.
How to Monitor Copier Activity and Modify Machine Settings
Key Operator Mode System Initial
How to Access the Key Operator Mode..11-2 [1] System Initial...11-4 [2] Copier Initial...11-7 [3] Preset Key...11-15 [4] E.C.M. (Electronic Copy Monitor)..11-18 [5] Lock Job Memory...11-27 [6] Paper Type...11-28 [7] Panel Contrast...11-29 [8] Key Operator Data..11-30 [9] Weekly Timer...11-31 [10] Touch Panel Adjustment...11-40 [11] Power Save...11-41 [12] Memory Switch...11-42 [13] List Print...11-47 [14] Application Customize...11-48 [15] Density Shift...11-49 [16] KRDS Host...11-50

[5] Output

Set initial Output mode of the Finisher, Inner tray or exit tray to be effective after power is turned on or after Auto Reset occurs.

Machine with Finisher

Setting options: EXIT Tray 1/ Tray 2/ Tray 3/ Tray 4; OUTPUT MODE Non-sort/ Sort/ Group/ Staple; Automatic Rotation on/off Default setting: EXIT Tray 1; OUTPUT MODE Non-sort; Automatic Rotation ON

Machine with Inner Tray

Setting options: EXIT Tray 1/ Tray 2; OUTPUT MODE Non-sort/ Group/ Rotation sort/ Rotation group; Automatic Rotation on/off Default setting: EXIT Tray 1; OUTPUT MODE Non-sort; Automatic Rotation ON

Machine without Finisher

Setting options: OUTPUT MODE Non-sort/ Group/ Rotation sort/ Rotation group; Automatic Rotation on/off Default setting: OUTPUT MODE Non-sort; Automatic Rotation ON
Key Operator Mode Screen Copier Initial Setting Menu Screen Output Mode Initial Setting Screen (machine with Finisher)
Output Mode Initial Setting Screen Output Mode Initial Setting Screen Staple Location Initial Setting Screen (machine with Inner tray) (machine with Finisher)
1 Touch 2. Copier Initial to display the Copier Initial Setting Menu Screen, then touch 5. Output to display the Output Mode Initial Setting Screen. 2 For the machine with Finisher, perform the following operation and proceed to step 5. To select the exit tray, touch TRAY 1 or TRAY 2. To select the Output mode, touch SORT, GROUP, or STAPLE. NOTES: 1. If STAPLE is selected, SORT is automatically highlighted. 2. If selecting Non-sort mode, do not highlight any of the SORT, GROUP, or STAPLE. To select the desired staple location, touch STAPLE SET. Touch the desired location on the Staple Location Initial Setting Screen, and touch OK. You can also select on/off of the Automatic rotation initial setting. To release the Automatic rotation mode, touch AUTO so that it is no longer highlighted. 3 For the machine with Inner tray, perform the following operation and proceed to step 5. To select the exit tray, touch TRAY 1 or TRAY 2. To select the Output mode, touch GROUP, ROTATION SORT, or ROTATION GROUP. You can also select on/off of the Automatic rotation initial setting. To release the Automatic rotation mode, touch AUTO so that it is no longer highlighted. 4 For the machine without Finisher, perform the following operation and proceed to step 5. To select the Output mode, touch GROUP, ROTATION SORT, or ROTATION GROUP. You can also select on/off of the Automatic rotation initial setting. To release the Automatic rotation mode, touch AUTO so that it is no longer highlighted. 5 Touch OK to complete the setting and return to the Copier Initial Setting Menu Screen. If other copier initial setting changes are required, touch the desired key. 6 Touch RETURN to restore the Key Operator Mode Screen. 7 If no further changes are required, touch RETURN to restore the Basic Screen to perform copying operations.

[15] Density Shift

Density shift divides each of nine density levels into two levels of lighter and three levels of darker when used in combination with Text/Photo Enhance. Density shift selection can be made in each of four Text/Photo Enhance modes; Text/ Photo (general), Text, Photo, and Increase Contrast.
Setting options: Density shift 0/ 1/ 2/ 3 (standard)/ 4/ 5
Density shift 0 Density shift 1 Density shift 2
Density shift 3 Density shift 4 Density shift 5

Key Operator Mode Screen

Density Shift Setting Screen
1 Touch [15] Density Shift to display the Density Shift Setting Screen. 2 Select the Text/Photo Enhance mode. Touch Text/Photo, TEXT, PHOTO, or Increase contrast to highlight it, then enter the desired density shift (from 0 to 5) using the Control panel keypad. 3 Touch OK to complete the settings and return to the Key Operator Mode Screen. 4 If no further changes are required, touch RETURN to restore the Basic Screen to perform copying operations.

[16] KRDS Host

When activated, the Remote Diagnostics option is automatically monitored by a Konica service representative. In case of machine trouble, select the KRDS host option. Your service representative will contact you to determine the appropriate means for resolving the problem.
Setting options: Call for JAM; SC; No toner; No paper; Copy quality; Other reason
Key Operator Mode Screen KRDS Host Menu Screen

Start Call Screen

1 Touch [16] KRDS host to display the KRDS Host Menu Screen. 2 Touch 1. JAM concerns, 2. SC concerns, 3. NO TONER, 4. NO PAPER, 5. COPY QUALITY, or 6. OTHER REASON, as required. The Start Call Screen will be displayed. 3 Touch START to call remote service representative. 4 Touch RETURN to restore the Key Operator Mode Screen. 5 If no further changes are required, touch RETURN to restore the Basic Screen to perform copying operations.

symbol

[#] (CLEAR QTY.) key 2-8, 3-7 [] (COUNTER) key 2-8, 10-14 [ ! ] symbol 2-15 Automatic Tray Switching (ATS) vii AUTO RESET effect 11-44 Auto Reset Mode vii
Basic Screen 2-6 Blank sheet interleaving 8-17 Book Copy 8-23 Booklet 8-14

Number

1 SHOT indication time 11-46 1.00 Magnification mode 3-12 1-2, 2-2 copying 3-18 1-2 Upside Down 8-36 2-1 copying 3-22 2-1 Upside Down 8-in 1 8-Repeat 8-in 1 8-Repeat 8-47 5.5x8.5 orig. type 11-in 1 8-Repeat 8-47