AU-201H Authentication Unit (HID Proximity Card Type)

Users Guide

Introduction
Thank you for choosing this device.
This Users Guide provides descriptions of the operating procedures and precautions for using AU-201H Authentication Unit (HID Prox IC Card Type). Carefully read this Users Guide before using this device. The actual screens that appear may be slightly different from the screen images used in this Users Guide. AU-201H Authentication Unit (IC Card Type) is hereafter referred to as this device. Manual conventions Caution: This warns of a possibility of damage to this device. Important: This indicates instructions that should be followed to ensure correct functionality and efficiency of this device. Note: This indicates an item of general importance. Reminder: This indicates an item of relative importance. Detail: This indicates an item of specific importance. Microsoft and Windows are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. All other company names and product names mentioned in this Users Guide are either registered trademarks or trademarks of their respective companies. Unauthorized use or reproduction of this Users Guide, whether in its entirety or in part, is strictly prohibited. The information contained in this Users Guide is subject to change without notice.
Trademark/copyright acknowledgements

Restrictions -

Product features
This device is an IC card authentication system that performs user authentication by IC cards and supports most HID Proximity (125MHz) IC cards. Logon and print job operations can be authenticated with IC cards when using multifunctional products with user authentication settings specified.

AU-201H

HID Prox IC cards compatible with this device must be prepared. The optional local interface kit and working table must be installed on the multifunctional product. Refer to Chapter 5 - Specifications.

Prerequisites

Note: In order to use this device, multifunctional product settings must be specified by the technical representative.
Using AU-201H Authentication Unit
In order to use this device, user IC card IDs must first be registered with the machine. A registered user can log on to a multifunctional product or print a print job after completing authentication with their IC card IDs. The following procedures describe how to specify the necessary settings on the multifunctional product, register users, and perform the logon and print job operations after completing authentication.
Important Do not disconnect the USB cable while this device is being used, otherwise the system may become unstable. Caution Do not store the IC card within 1.5 inches (approx.) of the card scanning area.
Multifunctional product settings
Detail: User authentication on the multifunctional product must be set for machine authentication.
From the control panel of the multifunctional product, press the [Utility/ Counter] button, press [Administrator Settings] and enter the administrator password, touch [User Authentication/Account Track] on the Administrator Settings screen, and then touch [General Settings].
Using AU-201H Authentication Unit Set User Authentication to ON (MFP), and then touch [OK].
Reminder: External server authentication is not supported. For details on specifying settings for Public User Access and Account Track, refer to the Users Guide [Copy Operations] included with the multifunctional product. When combined with account track settings, set Synchronize User Authentication & Account Track to Synchronize. If Do Not Synchronize is selected, the Touch & Print function cannot be used.
Touch [Authentication Device Settings], then [General Settings], then [Card Authentication]. Select the desired settings under IC Card Type and Operation Settings. Under IC Card Type, select the type of IC card to be used.

Using AU-201H Authentication Unit
Under Operation Settings, select the logon method after registration. Card Authentication: Logon is possible simply by positioning the IC card. Card Authentication + Password: Logon is possible by positioning the IC card and entering the password. If users are registered with Card Authentication + Password selected, the Touch & Print function cannot be used. For details on logging on, refer to Logging on to a multifunctional product on page 23.
Touch [OK], and then touch [OK] in the next screen that appears. Touch [Touch & Print Setting].
Select the printing method for the Touch & Print function.
Print All Jobs: Select this setting to print all documents after completed authentication once when multiple documents are saved in the Touch & Print user box. Print Each Job: Select this setting to print one document saved in the Touch & Print user box each time authentication is completed. If OFF is selected, the Touch & Print function cannot be used. For details on the Touch & Print function, refer to Touch & Print function on page 25. 7
Touch [OK]. Touch [Logoff Settings].
Select whether or not the user is logged off when scanning of the document is finished after the user has logged on to this machine.
Touch [OK]. Touch [Close], and then touch [Close] in the next screen that appears.

Registering users

There are two methods for registering users. Connecting this device to the multifunctional product and registering directly from the multifunctional product Connecting this device to a computer and registering using Data Administrator
Detail: Registered user data is stored on the hard disk of the multifunctional product. If the user authentication method on the multifunctional product is changed or the hard disk is reformatted, the registered user data is erased.
Registering from the control panel of the multifunctional product
From the control panel of the multifunctional product, touch [User Authentication/Account Track] on the Administrator Settings screen, and then touch [Authentication System], then [User Registration].
Touch the button for a registration number, and then touch [Edit].

Touch [Register Auth. Info.].

Touch [Edit].

Using AU-201H Authentication Unit Position the IC card on this device, and then touch [OK].
After the message Registered appears, touch [Close], and then touch [Close] in the next screen that appears. Type the user name and the password. If desired, specify the function limitations. Touch [OK]. Touch [Close].
Registering from Data Administrator
In order to use Data Administrator, settings must be specified on the multifunctional product and the setup procedure must be performed. The setup procedure includes installing this devices IC Card Driver (USB-Driver), then installing Data Administrator IC Card Plugin.
Reminder: Data Administrator ver. 3.0 or later must first be installed on the computer. For details on the operating environment and installation procedure for Data Administrator, refer to the Users Guide for the Data Administrator. Setup
Turn off the multifunctional product with the main power switch, and then disconnect this device from the multifunctional product. Install IC Card Driver (USB-Driver). Plug the cable from this device into the USB port on the computer. The Found New Hardware Wizard starts. Select Yes, now and every time I connect a device, and then click [Next].
Insert the application CD-ROM included with this device into the CD-ROM drive of the computer.
Using AU-201H Authentication Unit Select Install from a list or specific location (Advanced), and then click [Next].
Select the Include this location in the search check box, check that the application CD-ROM appears as a location to be searched, and then click [Next].
If the application CD-ROM does not appear as a location to be searched for the driver, click [Browse], select the IC Card Driver (USB-Driver) folder on the CD-ROM, and then click [OK].

The installation begins.

Click [Finish].
The installation of IC Card Driver (USB-Driver) is completed.
Install Data Administrator IC Card Plugin. Open the IC_Card_Plugin folder on the application CD-ROM, and then click setup.exe. Select the language, and then click [OK].

The installer starts up.

Follow the instructions that appear on the screen to complete the installation.

Click [Next].

Select I accept the terms of the license agreement, and then click [Next].

Click [Install].

Data Administrator IC Card Plugin is installed, and the setup is completed.
Using AU-201H Authentication Unit Registering users
Detail: In order to register users with Data Administrator, this device must be connected to the USB port of the computer, and the computer and multifunctional product must be connected over a network.

USB Network

Multifunctional product Computer This device
If this device is connected to the multifunctional product, turn off the multifunctional product with the main power switch, and then disconnect this device. If this device is connected to the computer, continue with step 4.
Note: When the multifunctional product is turned off, then on again with the main power switch, wait at least 10 seconds to turn the machine on after turning it off. The machine may not operate correctly if it is turned on immediately after being turned off. Hold the plug when plugging and unplugging the USB cable, otherwise the cable may be damaged. Turn on the multifunctional product with the main power switch. Connect this device to the USB port of the computer installed with Data Administrator.

Reminder:

Do not connect other USB devices to the same port where this device is connected. If enough USB power is not provided, this device may not operate correctly. When using a USB hub, be sure to use a self-powered USB hub that can provide 500 mA or more. After connecting this device, wait at least 5 seconds before operating it. Start up Data Administrator, and then import the device information for the multifunctional product. For details on importing the device information, refer to the Users Guide for Data Administrator. The Device information pane appears.
Select User authentication settings in the Function selection pane, and then click [Add].
Select a template, and then click [OK].
The User settings dialog box appears. AU-201H 19
Using AU-201H Authentication Unit Type in the user name and password, and then click the IC card authentication tab. If desired, type in the e-mail address.
Position the IC card on this device, and then click [Start reading]. The card ID can also be registered by selecting Input the card ID directly.
Click [OK]. Repeat steps 5 through 9 until all users have been registered.
Click [Export to the device].
To change the registered data, select the user name, and then click [Edit].

Click [Write].

The registered user data is specified on the multifunctional product. Detail: Data Administrator is equipped with a batch copy feature that allows the registered user data to be specified on multiple multifunctional products specified to be used with this device.

Click [OK].

Disconnect this device from this USB port of the computer. Turn off the multifunctional product with the main power switch, connect this device, and then turn on the multifunctional product with the main power switch.
Using AU-201H Authentication Unit Reminder:
When the multifunctional product is turned off, then on again with the main power switch, wait at least 10 seconds to turn the machine on after turning it off. The machine may not operate correctly if it is turned on immediately after being turned off. Hold the plug when plugging and unplugging the USB cable, otherwise the cable may be damaged.

Logging on to a multifunctional product
Follow the procedures described below to log on to multifunctional products by completing authentication with IC card IDs. When Card Authentication has been specified % Position the registered IC card on this device.
The user is authenticated, and the Basic screen appears.
Using AU-201H Authentication Unit When Card Authentication + Password has been specified Position the registered IC card on this device, and then type in the password.
Touch [Login] or press the [Access] key. The user is authenticated, and the Basic screen appears.
Note: The notification beep sounds while scanning. The notification beep is canceled by touching [Login] or pressing the [Access] key to complete authentication. This is a normal operation of the device. If authentication fails many times, the authentication data may not be registered correctly. Therefore, register the user again.
Touch & Print function
Print jobs sent from a computer are saved in the Touch & Print user box on the multifunctional product and can be printed after authentication is completed with IC card IDs. This is called the Touch & Print function. In addition, documents saved in the Touch & Print user box can be checked and specified to be printed from the control panel of the multifunctional product. The following printer drivers and computer operating systems are compatible with the Touch & Print function.
Printer driver PCL Driver Page description language PCL6 Supported operating systems Windows NT 4.0 (Service Pack 6a), Windows 2000 Professional (Service Pack 4 or later), Windows XP Home Edition/Professional (Service Pack 2 or later), Windows XP Professional x64, Windows Server 2003, and Windows Server 2003 x64 Windows 2000 Professional (Service Pack 4 or later), Windows XP Home Edition/Professional (Service Pack 2 or later), Windows XP Professional x64, Windows Server 2003, and Windows Server 2003 x64 Mac OS X 10.2, Mac OS X 10.3, and Mac OS X 10.4
PostScript Driver (PS driver)

PostScript3 Emulation

PostScript PPD driver (PS-PPD)
Detail: To use the Touch & Print function, select Card Authentication under Operation Settings and set Touch & Print Setting to ON.
Note: For details on the printer driver settings and Box mode functions, refer to the User's Guide included with the multifunctional product.
3.4.1 Touch & Print (For Windows)
Specifying settings on the Configure tab
For Windows 2000/NT 4.0, click the [Start] button, point to Settings, and then click Printers. For Windows XP/Server 2003, click the [Start] button, and then click Printers and Faxes. If Printers and Faxes does not appear in the Start menu, open the Control Panel from the Start menu, select Printers and Other Hardware, and then select Printers and Faxes.
Right-click the icon of the installed printer, and then click Properties. Click the Configure tab.
Select User Authentication under Device Option. Select Device from the Setting drop-down list. Click [Apply], and then click [OK].
Using AU-201H Authentication Unit Sending a print job
Open the data in the application, click [File], and then click [Print]. Check that the printer name has been selected in Printer Name or Select Printer. If the printer is not selected, click to select the printer.
The Print dialog box differs depending on the application.
Click [Preferences] (or [Properties]). Click the Basic tab.
From the Output Method drop-down list, select Print. 27
Using AU-201H Authentication Unit Click the [Authentication/Account Track] button. Select Recipient User, and then enter the user name and password.
Click [Verify] to check the user ID. Click [OK]. If the user name or the password is incorrect, type in the correct information.
Click the [OK] button. Specify the desired settings, and then click [OK]. Click [Apply], and then click [Print]. The print job is sent.
Position the registered IC card on this device.
Make sure that Begin Printing is selected. To select the print job to be printed, touch [Screen Operation]. For details, refer to Selecting the print job to be printed from the control panel on page 32. The user is authenticated, and the print job is printed.

3.4.2 Touch & Print (for Macintosh)
Open the data in the application, click [File], and then click Print. Check that the printer name has been selected.
From the drop-down menu, select Output Method. From the Output Method drop-down list, select Print.
Select the User Authentication check box. The User Authentication dialog box appears. Select Recipient User, and then enter the user name and password.
Click the [OK] button. Specify the desired settings, and then click [Print]. The print job is sent. Position the registered IC card on this device.
Make sure that Begin Printing is selected. To select the print job to be printed, touch [Screen Operation]. For details, refer to Selecting the print job to be printed from the control panel on page 32.
Using AU-201H Authentication Unit The user is authenticated, and the print job is printed.
Selecting the print job to be printed from the control panel
Follow the procedure described below to select the document to be printed from those saved in the Touch & Print user box.
Touch [Screen Operation].
Position the registered IC card on this device. The user is authenticated, and the Basic screen appears.
Press the [User Box] key in the control panel.

Touch [Use Document].

Touch [System User Box].
Using AU-201H Authentication Unit Touch [Touch & Print User Box], and then touch [OK].
Select the document to be printed. Multiple documents can be selected. To select all documents, touch [Select All]. To cancel the selection of all documents, touch [Reset]. To check various information, such as the date/time when the document was stored and the document name, touch [Detail View].
Touch the [Print] under Action, and then touch [OK]. To delete the document, touch [Delete]. To check the document details, touch [Document Details]. The selected document is printed.
Detail: If authentication fails many times, the authentication data may not be registered correctly. Therefore, register the user again.
Care of AU-201H Authentication Unit

Caution Before cleaning this device, disconnect it from the multifunctional product. If a force is applied to the USB port, it may be damaged. When cleaning this device, do not allow water to enter the device, otherwise the system may be damaged. Never use organic solvents, such as benzene or alcohol, to clean this device, otherwise it may be damaged.
Note: When disconnecting or connecting this device, turn off the multifunctional product with the main power switch, and then wait at least 10 seconds before turning it on again. The machine may not operate correctly if it is turned on immediately after being turned off. Hold the plug when plugging and unplugging the USB cable, otherwise the cable may be damaged.
Frequency: Once a month, or when it is dirty Wipe this device with a soft, dry cloth. If this device cannot be cleaned by wiping it, wash it with a cloth dampened with a mild detergent and wrung out well. After this device is cleaned, rinse the cloth and wring it out well before wiping off the detergent.

Specifications

Product name Dimensions Weight Power requirements Environment conditions (when operating) Environment conditions (when not operating) Radio waves classification Compatible card Computer Processor Memory Hard disk drive Monitor Network Application Temperature Humidity Temperature Humidity AU-201H Authentication Unit Approx. 3.15 (W) 2.64 (D) 1.1 (H) Approx. 3.88 oz Through USB port 32 to 131 degrees F 10 to 90% rH 32 to 131 degrees F 10 to 90% rH Induced reading/writing communication equipment HID Contactless Prox IC card (125MHz) PC/AT compatible, 1 GHz or more 128 MB or more Available hard disk space: 100 MB or more pixels, 16-bit color or more TCP/IP protocol Microsoft Internet Explorer 6.0 (Service Pack 1) or later Microsoft.NET Framework (Service Pack 1) or later USB 1.1 or later Windows 2000 Professional (Service Pack 4) Windows XP Professional Edition (Service Pack 2)
Interface Supported operating systems

Troubleshooting

If a problem occurs while running the system, refer to the following.
Condition The message Failed to register. appears on a multifunctional product where registration failed. The message appears on a computer where registration failed. Logon failed. The message Failed to Authenticate. appears on the multifunctional product. Scanning does not begin. Possible cause With this device, the scanning time is limited to 10 seconds. This message appears if scanning was not possible within the limited period of time. Remedy Refer to the Quick Guide Authentication Unit (IC Card Type AU-201) and check how to position the IC card in order to complete scanning within the limited period of time. Check the password, and type it in correctly.

If Card Authentication + Password was selected: Is the password typed in correctly? Was the multifunctional product restarted after this device was connected to it?
Turn the multifunctional product off with the main power switch and temporarily disconnect the USB cable from this device or the multifunctional product before connecting it again and waiting 10 seconds before turning on the multifunctional product with the main power switch. If this device is connected to a USB port different from the one used when the driver was installed, the Add New Hardware Wizard may start. Use the same USB port used when the driver was installed.
The Add New Hardware Wizard starts when this device is connected to the computer.
Is this device connected to the same USB port used when the driver was installed?
If the problem is not corrected after the described operation is performed, contact your technical representative.

PageScope Enterprise Suite gives you a powerful set of management tools to get a grip on managing print output, tracking costs and accounts, authenticating users, even customizing individual preferences at multiple MFPs.
PageScope Enterprise Suite: interlocking solutions to manage your printer and MFP fleet more productively.
Now in v2.0, with added functions and enhanced security capabilities, PageScope Enterprise Suite is a server-based solution for managed printing, account tracking, user authentication and customized operator interface. It can play an essential role in networked print management and by saving time in document printing, device setup and administrator management, PageScope Enterprise Suite can create overall system savings that benefit your bottom line. Whether youre already an enterpriselevel user or a fast-growing business with emerging needs, you can count on Konica Minoltas PageScope Enterprise Suite for sophisticated functions, simple operation and superb performance a proven solution for higher productivity.
PageScope Enterprise Suite v. 2.0: simple server-based management tools to optimize your document power.
With PageScope Enterprise Suite, Konica Minolta raised the bar in productivity and brought enterprise-level management efficiency to fast-growing businesses large and small. With v2.0, weve added new print management and security features to speed your prductivity and protect your data. Not only will you optimize the power of your networked MFPs, youll also find cost reductions you can count on in end-user benefits that save time and simplify the process of printing, scanning, sharing and safeguarding vital business information. PageScope Enterprise Suite runs on a central server in your organization so it doesnt require hardware add-ons or software enhancements on each networked MFP. With quick setup and seamless interoperability, PageScope Enterprise Suite saves you money right from the start. And for managing an entire fleet of bizhub and MIB-compliant MFPs from a centralized server, PageScope Enterprise Suite links to Konica Minoltas PageScope NetCare Device Manager a simple, powerful enterprise solution that lets IT administrators track all print meter counts and user activity, use programmable templates to configure network settings and default settings for one or all MFPs, and receive Email notifications when errors occur or supplies are running low.
PageScope MyPrint Manager:
The latest enhancement to PageScope Enterprise Suite Stores print jobs on MyPrint Manager server Enables secure document release at any MFP on the network Eliminates wasted print jobs Prevents confidential documents from sitting in output trays Lets finishing features be programmed directly at MFP panel Creates point and print server-based production efficiency Allows drivers to be pre-defined with default settings, etc. Provides flexible job storage, authentication and print driver support
PageScope Account Manager:
Tracks activity based on user log-in or MFP Tracks copy, fax, print and scan, distinguishes between color and B&W Creates reports to allocate costs more efficiently Sets limits, creates Email warnings, saves time for IT administrators Tracks usage by departments and users Allows departmental bill-back based on individual user

PageScope MyPanel Manager:
Gives each end-user a customized interface at each MFP Allows preprogrammed shortcuts based on user log-in Allows access to personal address books at each control panel Synchronizes with personal Outlook Address Book When user logs out, personal information is removed from the MFP Provides scanning to personal Email, scanning to personal home folder
PageScope Authentication Manager:
Synchronizes to Active Directory, automatically adds new users, disables removed users Provides password-protected log-in at each MFP Increases security through a wide range of authentication methods Enables state-of-the-art IC card and biometric authentication Allows card self-registration directly at any MFP
PageScope MyPrint Manager
Managing print jobs can be a difficult and time-consuming task especially in multi-MFP networks with heavy document workloads. But PageScope MyPrint Manager makes it easy. People on the move want the ability to print documents anywhere, any time. MyPrint Manager supports mobile users while helping to reduce waste and protect sensitive and personal information. MyPrint Manager holds documents in a secure print queue until users authenticate themselves at any supported Konica Minolta MFP, anywhere on your print network. Once authentication is complete, a user can select one or all documents as well as program many print functions directly on the MFP control panel including duplexing, stapling and hole-punching.
Automatic driver configuration for Active Directory users: all printing is tracked based on Windows log-in with no driver configuration needed, eliminating help desk calls when network passwords expire or have been changed simply log into a PC and all printing is tracked. Creates Point and Print functionality,
with pre-defined default settings stored on the PageScope Enterprise Suite server. Defaults can be changed by users for special projects or needs.
Defined job settings at the MFP panel include simplex/duplex, stapling (none, corner, 2 staple), and hole-punch (none, 2-hole) for the kinds of documents you print most often. Job details can be accessed by administrators, including user name, document size, time of sending and printing, number of pages, etc. ID & Print convenience can be set by each user,
selecting Use ID & Print or Print from List.
Flexible authentication methods allow enduser authentication by Active Directory in server-based environments or by Port Monitor with end-users entering credentials into the Port Monitor utility. Job storage with greater flexibility to save print

jobs until printed, automatically delete jobs not printed, create secure folders for stored jobs, register job details and device settings, etc.
Wide-ranging driver support for most current and future color and B&W bizhub MFPs so both new and existing equipment can be brought into your MyPrint system. Universal Printer Driver support to reduce the need for IT administration and configuration.
PageScope Account Manager
Affordable, enterprise-level account tracking is now within reach of any-sized business. By tracking document activity on your entire network, you can quickly determine who did what, at which machine, and when tracking activity on a whole network of Konica Minolta bizhub and other MIB-compliant multifunctional devices without requiring hardware or software components at each machine. PageScope Account Manager also helps you manage document output, control costs, and allocate expenses to specific individuals, workgroups, departments or projects all with minimum setup and oversight, saving valuable time for busy IT administrators.
Breaks out per-page activity for copy, fax, print and scan on bizhub devices, so you can accurately manage costs for multiple information pathways. Tracks total meter counts for all MIBcompliant printers, including other manufacturers networked MFPs and Konica Minolta bizhub devices. Separates color and B&W activity with tracking on a per-page level for Konica Minolta MFPs. Records a single end-users activities on multiple MFP devices based on individual log-in. Automatically compiles data based on
end-users, groups, devices and other criteria that suit your business workflow and account tracking needs.
Protects information by storing data separately no counts or user data are stored at the MFP.
PageScope Authentication Manager
In the digital networked era, security is a growing priority and the challenge is protecting information without compromising productivity and efficiency. PageScope Authentication Manager makes the process quick, simple and secure by enabling individuals to log on at each MFP as quickly easily as logging on to networked PCs. PageScope Authentication Manager automatically synchronizes to your Active Directory server to reduce the need for IT administration or you can configure authentication directly to the Authentication Manager server itself. And no user information is compromised, because log-in data is stored safely away from the MFP. PageScope Authentication Manager allows a wide range of server-based methods, including user name and password, optional AU-201H HID Proximity card or AU-202H iClass card reader, even the advanced Konica Minolta AU-101 or AU-102 Biometric Authentication option, all with quick ID and print convenience.
Adds users automatically upon first
authentication at any supported MFP on the network.
Auto Synchronization to Active Directory: automatically adds new users, disables removed users. Reduces administrator effort when new employees are added because they can be brought into Authentication Manager automatically. Begins tracking immediately for each enduser based on log-in at any MFP, for seamless account tracking and device management. Automatic driver configuration for Active Directory Users: all printing is tracked based on Windows log-in with no driver configuration needed, eliminating help desk calls when network passwords expire or have been changed simply log into a PC and all printing is tracked. Automatic Email address programming for

each end-user, to provide instant contact data and speed communication.
All Email from the MFP is sent from the logged-in user, not a generic account. Card authentication with the optional AU-201H HID Proximity Card Reader or AU-202H iClass card reader and syncs with active directory information to authenticate users by name, not just by numbers. User self-registration directly at the MFP by entering a user name and password and placing a card near the reader to register; the next time a user logs in, simply placing the card near the reader will gain access. Dual factor authentication for those requiring

more secure access.

Biometric authentication interface with the
AU-101 or AU-102 Biometric Authentication Unit that recognizes unique physical characteristics of each user more accurate than fingerprints.
Advanced security protection by storing
password and authentication data separately on the PageScope Enterprise Suite server no log-ins, counts or user data are stored at the MFP.
PageScope MyPanel Manager
Take the next step in document speed and convenience by creating a personal, customized interface screen that will appear at any networked MFP when you log in. PageScope MyPanel Manager recognizes your log-in and remembers your preferences changing screens or colors, specifying commonly used functions such as duplexing, creating up to 12 shortcut keys that speed productivity, and changing the desired language. PageScope MyPanel Manager also gives you access to your personal address book at any bizhub device, with the option to synchronize to your MS Outlook Address Book. Whichever networked machine you use, your interface will remain the same and the moment you log out, your personal data disappears from the MFP.
Speeds operation by providing a customized, recognizable interface at every Konica Minolta bizhub device. Change MFP display language based on
individual user preference.
Appears automatically at log-in for every end-user at any machine, so operation can be quick and simple anywhere on your network. 12 shortcut keys can be easily
preprogrammed to automate routine operations such as duplexing, stapling, holepunching or other functions.
Personal address book data can be made
available at any bizhub device, for quick scanning and sharing by any method available at the device including fax.

Enables synchronization with your personal

Outlook Address Book.

Protects personal data by removing it from
the MFP as soon as the user logs out with data stored separately on the PageScope Enterprise server.
Scan-to-Me/Scan-to-Home automatically creates scan destinations to the users personal Email address and personal network home folder as outlined in Active Directory. Restricted scanning allows you to restrict the ability to manually input any other scan destinations.
PageScope Enterprise Suite: for productivity every enterprise can count on.
Modular design, simple operation, seamless interoperability together, they make PageScope Enterprise Suite an essential management tool in todays competitive environment. Call today for more information.
HARDWARE REQUIREMENTS Pentium 4 2GHz or higher / 1GB RAM or higher 500MB space or higher for installation (dedicated server with 60GB or higher recommended) BROWSER REQUIREMENTS Microsoft Internet Explorer 6.0 or later / Mozilla Firefox 3.5 or later Apple Safari 2.0 or later (Mac OS only) OTHER REQUIREMENTS Microsoft.NET Framework 2.0 or later Microsoft Internet Information Services 5.0 or later Microsoft SQL Server 2000 Standard Edition/Enterprise Edition Microsoft SQL Server 2005 or 2008 Express Edition/Standard Edition/Enterprise Edition
SUPPORTED OPERATING SYSTEMS Windows 2000: Windows XP: Server (SP4 or later) / Professional (SP4 or later) / Advanced Server (SP4 or later) Professional (SP3 or later) / Professional x64 Edition (SP2 or later)
Windows Server 2003: Standard Edition (SP2 or later)*/ Enterprise Edition (SP2 or later)* R2 Standard Edition (SP2 or later)* / R2 Enterprise Edition (SP2 or later)* Windows Vista: Business (SP2 or later)* / Enterprise (SP2 or later)* / Ultimate (SP2 or later)* Windows Server 2008: Standard (SP2 or later)* / Enterprise (SP2 or later)* Standard without Hyper-V (SP2 or later)* / Enterprise without Hyper-V (SP2 or later)* R2 Standard / R2 Enterprise Windows 7: Professional* / Enterprise* / Ultimate*
*32-bit (x86) and 64-bit (x64) editions of Windows are supported.
SUPPORTED DEVICES bizhub 200, 250, 350 bizhub 222, 282, 362 bizhub 223, 283, 363, 423 bizhub 360, 420, 500 bizhub 361, 421, 501 bizhub 40P bizhub 600, 750 bizhub 601, 751 bizhub C10(P) bizhub C20(P) bizhub C200 bizhub C203, C253, C353 bizhub C220, C280, C360 bizhub C250(P) bizhub C252(P), C300, C352(P) (+ IC-406(Fiery)) bizhub C300 (+ IC-406(Fiery)) bizhub C30P bizhub C31P bizhub C35 bizhub C351 (+ IC-402(Fiery)) bizhub C353P bizhub C35P bizhub C450(P) bizhub C450 + IC-402(Fiery) bizhub C451, C550, C650 bizhub C452, C552(DS), C652(DS) bizhub PRO 1050 bizhub PRO 1050e bizhub PRO 1050eP bizhub PRO 1050P bizhub PRO 1051 bizhub PRO 1200 bizhub PRO 1200P bizhub PRO 920 bizhub PRO 950 bizhub PRO C5500 + IC-408(Fiery) bizhub PRO C6500 + IC-303(Fiery) bizhub PRO C6500 + IC-305(Fiery) bizhub PRO C6500 + IC-408(Fiery) bizhub PRO C6500P + IC-303(Fiery) bizhub PRO C6500P + IC-305(Fiery) bizhub PRO C6500P + IC-408(Fiery) magicolor 1650EN magicolor 2450, 2550 magicolor 2590MF magicolor 3730DN, 3730N magicolor 4650DN, 4650EN magicolor 4690MF, 4695MF magicolor 4750DN magicolor 5430DL, 5440DL magicolor 5450, 5550, 5570 magicolor 5650EN, 5670EN magicolor 7440, 7450 magicolor 8650DN pagepro 1350EN, 4650EN, 5650EN

NETCARE DEVICE MANAGER COUNTER READER DEVICE LIST NEW NEW NEW NEW NEW NEW

AUTHENTICATION MANAGER

MyPANEL MANAGER

MyPRINT MANAGER

Please refer to each modules Read Me for the required Firmware versions.
KONICA MINOLTA BUSINESS SOLUTIONS U.S.A., INC. 100 Williams Drive Ramsey, NJ 07446
www.CountOnKonicaMinolta.com www.kmbs.konicaminolta.us
2010 KONICA MINOLTA BUSINESS SOLUTIONS U.S.A., INC. All rights reserved. Reproduction in whole or in part without written permission is prohibited. Konica Minolta is a registered trademark of KONICA MINOLTA HOLDINGS, INC. bizhub and PageScope are trademarks of KONICA MINOLTA BUSINESS TECHNOLOGIES, INC. All other brands and product names are registered trademarks or trademarks of their respective owners. Design & specifications are subject to change without notice. Some functions may require options, which may or may not be available at time of launch.