CF911P

Service Information

Trademarks

Minota and CF911P are registered trademarks or trademarks of Minolta Co., Ltd. Fiery, Fiery X2 are trademarks of Electronics for Imaging, Inc. Adobe, PostScript are registered trademarks of Adobe Systems Incorporated. EPS (Encapsulated PostScript) is a trademark of Altsys Corporation. PC/AT is a registered trademark of International Business Machines Corporation. Microsoft, MS-DOS, Windows and Windows NT are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. Apple, AppleTalk, EtherTalk and Mac are registered trademarks or trademark of Apple Computer Inc. QuarkXPress is a registered trademark of Quark, Inc. Times, Helvetica, and Palatino are trademarks of Linotype AG and/or its subsidiaries. UNIX is a registered trademark of UNIX System Laboratories. Ethernet is a registered trademark of Xerox Corporation. NetWare and Novell are registered trademarks and Internetwork Packet Exchange (IPX) is a trademark of Novell, Inc. All other products and company names are trademarks or registered trademarks of their respective holders.
Safety Precautions for Inspection and Service
When performing inspection and service procedures, observe the following precautions to prevent accidents and ensure utmost safety. Depending on the model, some of the precautions given in the following do not apply. Different markings are used to denote specific meanings as detailed below.

WARNING CAUTION

Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. It may also be used to alert against unsafe practices.
The following graphic symbols are used to give instructions that need to be observed. Used to call the service engineer attention to what is graphically represented inside the marking (including a warning). Used to prohibit the service engineer from doing what is graphically represented inside the marking. Used to instruct the service engineer to do what is graphically represented inside the marking.

WARNING

1. Always observe precautions. Parts requiring special attention in this product will include a label containing the mark shown on the left plus precautionary notes. Be sure to observe the precautions. Be sure to observe the Safety Information given in Operators Manual. 2. Before starting the procedures, be sure to unplug the power cord. This product contains a high-voltage unit and a circuit with a large current capacity that may cause an electric shock or burn. The product also contains parts that can jerk suddenly and cause injure. If this product uses a laser, laser beam leakage may cause eye damage or blindness. 3. Use the specified parts. For replacement parts, always use the genuine parts specified in the manufacturers Parts Manual. Installing a wrong or unauthorized part could cause dielectric breakdown, overload, or undermine safety devices resulting in possible electric shock or fire. Replace a blown electrical fuse or thermal fuse with its corresponding genuine part specified in the manufacturers Parts Manual. Installing a fuse of a different make or rating could lead to a possible fire. If a thermal fuse blows frequently, the temperature control system is probably of a problem and action must be taken to eliminate the cause of the problem.
4. Handle the power cord with care and never use a multiple socket. Do not brake, crush or otherwise damage the power cord. Placing a heavy object on the power cord, or pulling or bending it may damage it, resulting in a possible fire or electric shock. Do not use a multiple outlet to which any other appliances or machines is connected. Be sure the power outlet meets or exceeds the specified capacity. 5. Be careful about the high-voltage parts. A part marked with the symbol shown on the left carries a high voltage. Touching it could result in an electric shock or burn. Be sure to unplug the power cord before servicing this part or the parts near it. 6. Do not keep your hands wet when performing the procedures. Do not unplug or plug in the power cord, or perform any kind of service or inspection with wet hands. Doing so could result in an electric shock.

7. Do not touch a high-temperature part. A part marked with the symbol shown on the left and other parts such as the exposure lamp and fusing roller can be very hot while the machine is energized. Touching them may result in a burn. Wait until these parts have cooled down before replacing them or any surrounding parts. 8. Make a ground connection at all times (This item may not be effected in USA). Be sure to connect a ground wire to the ground terminal even when performing an inspection or repair. Without proper grounding, electrical leakage could result in an electric shock or fire. Never connect the ground wire to a gas pipe, water pipe, telephone ground wire, or a lightning conductor. 9. Do not remodel the product. Modifying this product in a manner not authorized by the manufacturer may result in a fire or electric shock. If this product uses a laser, laser beam leakage may cause eye damage or blindness. 10. Restore all parts and harnesses to their original positions. To promote safety and prevent product damage, make sure the harnesses are returned to their original positions and properly secured in their clamps and saddles in order to avoid hot parts, high-voltage parts, and sharp edges, or being crushed. To promote safety, make sure that all tubing and other insulating materials are returned to their original positions. Make sure that floating components mounted on the circuit boards are at their correct distance and position off the boards.

CAUTION

1. Precautions for Service Jobs A toothed washer and spring washer, if used originally, must be reinstalled. Omitting them may result in contact failure which could cause an electric shock or fire. When reassembling parts, make sure that the correct screws (size, type) are used in the correct places. Using the wrong screw could lead to stripped threads, poorly secured parts, poor insulating or grounding, and result in a malfunction, electric shock or injury. Take great care to avoid personal injury from possible burrs and sharp edges on the parts, frames and chassis of the product. When moving the product or removing an option, use care not to injure your back or allow your hands to be caught in mechanisms. 2. Precautions for Servicing with Covers and Parts Removed Wherever feasible, keep all parts and covers mounted when energizing the product. If energizing the product with a cover removed is absolutely unavoidable, do not touch any exposed live parts and use care not to allow your clothing to be caught in the moving parts. Never leave a product in this condition unattended. Never place disassembled parts or a container of liquid on the product parts falling into, or the liquid spilling inside, the mechanism could result in an electric shock or fire. Never use a flammable spray near the product. This could result in a fire. Make sure the power cord is unplugged before removing or installing circuit boards or plugging in or unplugging connectors. Always use the interlock switch actuating jig to actuate an interlock switch when a cover is opened or removed. The use of folded paper or some other object may damage the interlock switch mechanism, possibly resulting in an electric shock, injury or blindness. 3. Precautions for Working Environment The product must be placed on a flat, level surface that is stable and secure. Never place this product or its parts on an unsteady or tilting workbench when servicing. Provide good ventilation at regular intervals if a service job must be done in a confined space for a long period time. Avoid dusty locations and places exposed to oil mist or steam. Avoid working positions that may block the ventilation port of the product. 4. Precautions for Handling Batteries (Lithium, Nickel-Cadmium, etc.) Replace a rundown battery with the same type as specified in the manufacturers parts manual. Before installing a new battery, make sure of the correct polarity of the installation or the battery could burst. Dispose of used batteries according to the local regulations. Never dispose of them at the users premises or attempt to try to discharge one.

5. Precautions for Laser Beam (Products Employing Laser Only) Removing the cover marked with the following caution label could lead to possible exposure to the laser beam, resulting in eye damage or blindness. Be sure to unplug the power cord before removing this cover. If removing this cover while the power is ON is unavoidable, be sure to wear protective laser goggles that meet specifications. Make sure that no one enters the room when the machine is in this condition. When handling the laser unit, observe the Precautions for Handling Laser Equipment.

1167P001AA

Invisible laser radiation when open.

AOID DIRECT TO BEAM

EPOSURE

0947-7127-01 1144D270AA

Other Precautions
To reassemble the product, reverse the order of disassembly unless otherwise specified. While the product is energized, do not unplug or plug connectors into the circuit boards or harnesses. The magnet roller generates a strong magnetic field. Do not bring it near a watch, floppy disk, magnetic card, or CRT tube. An air gun and vacuum cleaner generates a strong electrostatic charge that can destroy the ATDC sensor and other sensors. Before cleaning a component with one of these devices, be sure to remove all the sensors. Otherwise, use a blower brush and cloth when cleaning parts. When handling circuit boards with MOS ICs, observe the INSTRUCTIONS FOR HANDLING THE PWBs WITH MOS ICs (applicable only to the products using MOS ICs). The PC Drum is a very delicate component. Observe the precautions given in HANDLING OF THE PC DRUM because mishandling may result in serious image problems. Note that replacement of a circuit board may call for readjustments or resetting of particular items, or software installation. After completing a service job, perform a safety check. Make sure that all parts, wiring and screws are returned to their original positions. Check the area surrounding the service site for any signs of damage, wear or need of repair. Do not pull out the toner hopper while the toner bottle is turning. This could result in a damaged hopper motor or locking mechanism. If the product is to be run with the front door open, make sure that the toner hopper is in the locked position.
Used Batteries Precautions
(ALL Areas) CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturers instructions. (Germany only) VORSICHT! Explosinsgefahr bei unsachgemen austausch der batterie. Ersatz nur durch denselben oder einen vom hersteller empfohlenen hnlichen typ. Entsorgung gebrauchter batterien nach angaben des herstellers. (France) ATTENTION Ily a danger dexplosion sily a remplacement incorrec de la batterie. Remplacer uniquement avec une batterie du meme type ou dun type quivalent recommande par le constructueur. Mettre au rebut les batteries usages conformment aux instructions du fabricant. (Denmark only) ADVARSEL! Lithiumbatteri - Eksplosionsfare ved fejlagtig hndtering Udskiftning m kun ske med batteri af samme fabrikat og type. Levr det brugte batteri tilbage til leverandren. (Norway only) ADVARSEL Eksplosjonsfare ved feilaktig skifte av batteri. Benytt samme batteritype eller en tilsvarende type anbefalt av apparatfabrikanten. Brukte batterier kasseres i henhold til fabrikantens instruksjoner. (Sweden only) VARNING Explosionsfara vid felaktigt batteribyte. Anvnd samma batterityp eller en ekvivalent typ som rekommenderas av apparattillverkaren. Kassera anvnt batteri enligt fabrikantens instruktion. (Finland only) VAROlTUS Paristo voi rjht, los se on virheellisesti asennettu. Vaihda paristo ainoastaan laitevalmistajan suosittelemaan tyyppiin. Hvit Kytetty paristo valmistajan ohjeiden mukaisesti.

M: General/Mechanical/Electrical

CONTENTS

1. CF910 to CF911P Changes List.. 1 2. Dis/ Reassembly/Adjustment.. 2 3. General/Mechanical/Electrical.. 3 4. Switches on PWBs, Service Mode.. 4 5. Troubleshooting... 5 6. Operation Panel... 6 7. Connection Tools... 9 Connection to Notebook PC and X-Rite (DTP32). 9 Jig Software Set-Up.. 10 8. Replacement Pages... 11 Dis/ Reassembly/Adjustment
(D-114, 116, 131, 138, 150)
General/Mechanical/Electrical
(M-115). 19 (S-5, 7, 47, 51). 20
Switches on PWBs, Service Mode Troubleshooting

(T-2, 3, 4, 5, 6)

9. LCD Messages from User Guide, Administrator Guide. 29 Error messages.. 29 Print Server messages... 37
This manual contains explanations, modifications and replacements that
will make the CF910 Service Manual applicable to the CF911P Printer.
For all pages in the CF910 Service Manual, please read printer for the
word copier and print for the word copy.
D: DisReassembly/Adjustment
1. CF910 to CF911P Changes List
1-1. The CF911P does not contain the following CF910 parts (Electrical Parts List). LA1 M1 M2 M24 M25 PC1 PC2 PU2 PWB-A PWB-B PWB-G PWBSE1 SE2 SE3 SE4 Exposure Lamp Scanner Motor Original Glass Cooling Fan Motor IR Cooling Fan Motor 1 IR Cooling Fan Motor 2 Scanner Home Position Sensor Original Cover Angle Detection Sensor DC Power Supply 2 CCD Sensor Board A/D Converter Board Motor Drive Board Tech. Rep. Setting Switches Board Original Size Detecting Sensor 1 (OP) Original Size Detecting Sensor 2 Original Size Detecting Sensor 3 Original Size Detecting Sensor 4 (OP)
1-2. The following part has been changed. UN27 From CF910 Control Panel to CF911P Operation Panel.
1-3. The CF911P includes the new parts listed below. Fiery X2e PWB-E Printer Control Board Controller Interface Board
1-4. General manual changes. 1. Change the Touch Panel to the Control Panel and/or PC screen. 2. Change the Malfunction Reset switch to the Trouble Reset key on the panel that appears in Clear Mode on the PC screen. 3. Image stabilization problem indicator is not applicable. 4. Security Mode is not applicable. 5. Additional Notes: When the power is switched on but the CF911P Printer does not display Ready, switch the power Off and On again. When the Message Alert, Service Code is displayed, press the down key, display the Error Code on the second line.

2. Dis/ Reassembly/Adjustment

Manual Change List PAGE

D-1 D-7, 8

26.79 W Not applicable

Laser max power 8 mW PWB-A, PWB-B, PWB-G, PU2 UN27
Changed CF911P Operational Panel. Not applicable Not applicable Not applicable See replacement page 11. Not applicable See replacement page 13. See replacement page 14. Not applicable Not applicable Fig. 2 Program Transfer Mode screen of the software tool. See replacement page 18.
D-72 to 79 D-100 D-113 D-114 to 127 D-128 to 130 D-131 D-137 D-148 D-149 D-150
Optical Section IR (CCD Assy, Mirror Lens/Exposure Lamp/ Cable Touch Panel Correction Mode Setting Mode IR Area Developer Change Mode Gradation Adjust AE Adjust IR Area Fig. 2 Downloading Comp..
NOTE: When you dont have an X-Rite DTP32 densito meter, see page 17 (D-137-4) Another Gradation Adjust (Visual Calibration), in this manual.
3. General/Mechanical/Electrical

G-1 G-6

26.79 W Delete
Laser Radiation Power: 8mW Exposure Lamp, Original Scanning, Scanning Density, Exposure System, Types of Originals, Maximum Size of Original. Warming-up Time After Energy Saver Mode First Copy Time (Upper Drawer, 1.000, Manual Exposure Mode) Copying Speed for Multi Copy Cycle (Upper Drawer, 1.000) (Copies/min)
Not applicable First Print Time (Upper Drawer) Printing Speed for Multi Print Cycle (Upper Drawer) (Prints/min) Delete
Zoom Ratios, Void Image Width, Lens, Light Source, Exposure Lamp, Dimensions. Options (AFR-12, ADF Kit D, Editor Board, Editor Display, Mount Kit E, Data Controller D-102, Plug-in Counter). 50/60 Hz 0.3% System Options: 2. Plug-in Counter, 3. Duplexing Document Feeder, 4. Data Controller D-102, 5. Editor Display, 6. Editor Board. IR Unit 3. Photoelectric Conversion, 4. IR Scanner Drive Motor Scanner Motor M1, Exposure Lamp LA1, Scanner Motor M1, IR Control Board Chapter 9 Image Reader Section IR Digital image data. Press Start Key Full toner collecting box detection Key Counter CNT12, A/D Converter Board PWB-B, CCD Sensor Board PWB-A, DC Power Supply 2 PU2, Exposure Lamp LA1

G-10 G-12

50/60 Hz 3 Hz Delete
M-1 M-2, 3 M-5 M-6, 8 M-11 M-22 to 41 M-43 M-45 M-115 M-130, 131
Delete Not applicable Not applicable Not applicable Not applicable Not applicable Print digital image data. Print start signal. See replacement page 19. Not applicable
S: Switches on PWBs/Service Mode
4. Switches on PWBs, Service Mode
All pages S-3, 4 S-5 S-7 S-9 S-11 S-17 S-18 S-19 S-20 S-22 S-24 S-25 S-26 S-29 S-30 S-33 S-36 S-37 S-39 S-40 S-41 S-43 S-45, 46 S-47 S-50 S-51
PC screen Display. Change to Operation Panel illust. See page 7 in this manual. See replacement page 20. Does not have Tech. Rep. Switches Board. See replacement page 21. Not applicable Not applicable Changed to Serviceman Mode of PC screen. Not applicable Not applicable Not applicable Not applicable Not applicable Not applicable Not applicable Not applicable Not applicable Not applicable Not applicable Not applicable Not applicable Not applicable Not applicable Not applicable Not applicable See replacement page 22. Not applicable See replacement page 23.

D-137-1

If the printer is not printing, restart the Facte.exe program. This screen appears before the print cycle is completed. 1. Switch the Swticher to the B X-Rite position. (If the switch position is not changed, the PC screen shows _.) 2. To read the test print, click the Read TestPrint button. 3. To calibrate the X-Rite, click the Start DTP32 Calibration button. NOTE: Calibration is necessary when the message NEEDS CALIBRATION appears, or at roughly a weekly frequency. 5. Calibrate X-Rite. Insert the X-Rite Auto Cal Strip into the strip insertion slot.
Go to the next step when this LCD screen appears.

Test Print

6. Read the cyan data. Wait until the message Insert Cyan Pass appears. Set the X-Rite guide to 15 and slowly pass the test print through the X-Rite from the front so it can read the cyan data. This lets X-Rite start reading the data automatically. 7. Read the magenta data. Wait until the message Insert Magenta Pass appears. Set the X-Rite guide to 30 and slowly pass the test print through the X-Rite from the front so it can read the magenta data. 8. Read the yellow data. Wait until the message Insert Yellow Pass appears. Set the X-Rite guide to 10 and slowly pass the test print through the X-Rite from the front so it can read the yellow data. 9. Read the black data. Wait until the message Insert Black Pass appears. Set the X-Rite guide to 25 and slowly pass the test

D-137-2

print through the X-Rite from the front so it can read the Black data. 10. Transmit the correction values to CF911P. Switch the Switcher to the A CF911P position. (If the switch position is not changed, the PC screen shows _.) Click the Exit button.
Data is then transferred to the printer, showing the message Cyan Copying,." on the screen. At this time, the cyan gray scale pattern is printed to initialize CF911P.
11. This completes the color adjustment procedures. Repeating these adjustment procedures 3 times will allow the colors to saturate. To make readjustments, click the Start (RETURN) button to go back to step 4. Wait for CF911P to reply and repeat the adjustment procedures. Click the EX button to exit from the adjustment.

D-137-3

I Another GRADATION ADJUSTMENT Another Gradation Adjustment is Visual Calibration, when the X-Rite DTP32 is not being used. 1. To print out the VisualCal chart chart Limits and 30% Match (Fig. 1): Press the Menu key. Press the down key to select Reboot Server. Press the Set key. When the message To update/set up, press any key. appears, press any key. Press the down key to select Run Setup. Press the Set key to run the setup. Press the down key to select Calibration. Press the Set key. Press the down key to select Calibrate. Press the Set key. Press the down key to select Print limits pg?. Press the Set key. Press the down key to select Yes. The chart is printed out. 2. Perform the checkup by following the instructions on the chart. Use the up/down keys to change settings. 3. Follow up with the VisualCal chart Gray Balance check (Fig. 2). This chart is auto printed. The checkup instructions on the chart.

Fig. 1 VisualCal chart

Limits and 30% Match

Fig. 2 VisualCal chart

Gray Balance

D-137-4

FLASH MEMORY
Software has conventionally been upgraded by replacing ROM on each board. This printer employs flash memory for the system control IC mounted on the IR Control Board. Its contents are reprogrammed easily by performing the following steps using the IC card (memory card), into which data has been previously downloaded. NOTE NEVER remove or insert the memory card with the printer power turned ON.

Memory Card Cover

Fig. 1
1. With the Power Switch in the OFF position, unplug the power cord from the power outlet. 2. Remove the Hopper Unit. 3. Remove the two screws that secure the Memory Card Cover. 4. Install the Memory Card. See Fig. 1. 5. Select Program Transfer Mode from the CF911P in the menu bar of Service Software. 6. Plug the power cord into the power outlet. 7. Turn ON the Power Switch. This rewrites the data. 8. On the PC screen, make sure that the data has been properly written. See Fig.2. 9. Turn OFF the Power Switch. Unplug the power cord from the power outlet. 10. Remove the memory card.
Fig. 1 Memory Card Installation Position Insert the memory card into the specified position on the IR Control Board.
Fig. 2 Displayed on PC screen in Program Transfer Mode of the FACTE.exe service software.

PC Drum Cleaning

<Cleaning Operation> 1. The Cleaning Blade is pressed against the surface of the PC Drum to scrape toner off it. 2. The Paddle flips toner accumulated on the edge of the Cleaning Blade to the Toner Conveying Coil. Paper Take-Up Motor M15 3. The Toner Conveying Coil conveys toner to the Toner Collecting Box in the rear of the printer. Toner Conveying Coil Paddle Toner Conveying Coil

User mode The Meter Count counts are not cleared. Following Serviceman Mode items only: Fuser Oil Change Count Up Select Admin. Mode (access no.) RD-Mode : Cleared : Not cleared

S-7, 8

This mode is used to adjust and operate the Developing Unit. NOTE The Developer mode will only be outlined in this manual. For more details, see DIS/REASSEMBLY, ADJUSTMENT or TROUBLESHOOTING.
Developer Change Mode Menu Screen
Developer Change Mode Setting Procedure
<Setting Procedure> 1. Turn ON the Power Switch. 2. Open CF911P in the menu bar on the PC and click Dev Mode. 3. Open and close the Front Door. 4. From here on, perform the function according to the instructions on the screen.
NOTE The selected function is pops up on the screen.
<Exiting the Mode> Click the Ex. button.

DATE/TIME INPUT MODE

This mode is used to set the time-of-day and date.
Date/Time Input Mode Screen
Date/Time Input Mode Setting Procedure
<Procedure> 1. Open CF911P in the menu bar on the PC and click Serviceman Mode. 2. Click Machine Adjust and select Date and Time. 3. When the input screen appears, enter year, month, day, hour, and minute.
NOTE When setting the month, day, hour, or minute, enter 0 first if the data is one digit. 4. When the data has been entered, click OK.
Controlled Parts Check Procedure
This printer allows the Tech. Rep. to easily determine whether a particular controlled part is fully operational and check for printer operating conditions. (For details, see the following pages.) <Procedure> 1. When a paper misfeed or malfunction occurs, identify on the circuit diagram accompanying the text the controlled part that is probably responsible for the problem. 2. Open State Confirm from the Service mode menu and, from among the Switch 1 to 3 screens, select one that is associated with the part identified in step 1 above. 3. Change the state of the part in question and see if the signal is changed. <Example> When a paper misfeed occurs, Upper Drawer Paper Take-Up Sensor PC12 is considered to be responsible for it. <Procedure> 1. Remove the sheet of paper misfed. 2. Select Switch 1 (Paper) of State Confirm available from the Serviceman mode menu.

No cyan toner

No fuser oil

No magenta toner

Corrective action/additional information: The magenta (M) toner has run out. Replenish the magenta toner container according to the instructions in your printer manual. The Printer will resume printing when you have replaced the toner container. The stapler has run out of staples. The Printer will resume printing when you have refilled the stapler. The yellow (Y) toner has run out. Replenish the yellow toner container according to the instructions in your printer manual. The Printer will resume printing when you have replaced the toner container. There is a paper jam in the printer. The Printer will resume printing when you have cleared the paper jam. There is a paper jam in the printer. Open the printer doors and check the locations indicated on the printer display. The Printer will resume printing when you have cleared the paper jam and closed the printer doors. Someone has selected Suspend Print from the Functions menu on the Printer Control Panel. The Printer will resume printing when you select Resume Print at the Control Panel. There is a problem with the printer that requires service by a technician. Resend the job from the manual feed tray, or contact your authorized service/support technician in order to set up the printer for the specified media type. Resend the job from the manual feed tray, or contact your authorized service/support technician in order to set up the printer for the specified media type. Resend the job from the manual feed tray, or contact your authorized service/support technician in order to set up the printer for the specified media type. The sorter unit is unattached from the printer. The Printer will resume printing when you have reattached the sorter unit. The manual feed tray is not loaded with the thick1 paper specified. The Printer will resume printing when you have loaded thick1 paper into the manual feed tray. The specified tray is not loaded with the thick1 paper specified. The Printer will resume printing when you have loaded thick1 paper into the specified tray. The manual feed tray is not loaded with the thick2 paper specified. The Printer will resume printing when you have loaded thick2 paper into the manual feed tray.
No Staple No yellow toner
Paper jam Paper jam at ___
Printer is off-line Service Code ___ Set Plain type on printer Set Thick1 at printer Set Thin at printer Sorter is not attached Thick1 ___ in manual feed Thick1 ___ in tray ___ Thick2 ___ in manual feed

Thin ___ in manual feed Thin ___ in tray ___ Toner waste bottle not set To print, clear output area To print, reset printer Trans ___ in manual feed Tray problem <Lower> Tray problem <Middle> Tray problem <Upper> Unknown error Waiting. Warming up. Waste toner nearly full Waste toner full Yellow toner nearly empty
Corrective action/additional information: The manual feed tray is not loaded with the thin paper specified. The Printer will resume printing when you have loaded thin paper into the manual feed tray. The specified tray is not loaded with the thin paper specified. The Printer will resume printing when you have loaded thin paper into the specified tray. The printers waste toner bottle is not positioned correctly. The Printer will resume printing when you have installed the waste toner bottle in the correct place. The printers top output tray has reached capacity. The Printer will resume printing when all pages are removed from the tray. The printer must be power cycled. Turn the printer off and on. The manual feed tray is not loaded with the transparencies specified. The Printer will resume printing when you have loaded transparencies into the manual feed tray. There is a problem with the printers lower tray. The Printer will resume printing when you have resolved the problem. There is a problem with the printers middle tray. The Printer will resume printing when you have resolved the problem. There is a problem with the printers upper tray. The Printer will resume printing when you have resolved the problem. An error occurred with the printer. See the printer user interface for more information. The printer is recovering from an error (such as a paper jam) and will print when it is finished. The printer is warming up. When the printer has finished warming up, the Printer will begin the print job. The printers waste toner container is almost full. You should soon empty or replace the container. The printers waste toner container is full. The Printer will resume printing when you empty or replace the container. The yellow (Y) toner has almost run out. You should soon replenish the yellow toner container according to the instructions in your printer manual
Maintaining optimal system performance

You cannot connect to the Printer from Fiery Downloader. You cant print an EPS file using Fiery Downloader.
Check with the administrator to make sure that the Direct You have problems connection is enabled. downloading a font with Fiery Downloader. The Direct connection must be used to download fonts. (Files can be downloaded via the Print or Hold queue.) Extra blank page prints Turn off the Showpage (after EPS file) option. This option adds a special PostScript command that will cause an after a Fiery extra blank page to Downloader job. print if it is not needed.
Problems with Fiery WebTools
Clear the cache (Netscape Communicator) or history (Microsoft Internet Explorer).
From Administrator Guide Print Server messages
Network setup messages After this Setup screen:
Enable AppleTalk (Network Protocol Setup>AppleTalk Setup)

This message:

No AppleTalk zone found.

Means:

The Ethernet network cable is not attached to the connector on the Printer, or the network cable is not plugged into the hub or network. If your AppleTalk network has zones, and you want to specify a zone for the Printer, you must connect the network cable to the Printer before performing AppleTalk Setup. Also could mean that the AppleTalk network doesnt have zones. Zones are not required for printing to the Printer. Press OK to continue. Enable at least one network port in Port Setup before beginning Protocol Setup or Service Setup. The network hub is not connected to a Novell machine when the Printer tries to bind. No other IPX machine can be found on the network, or the network hub is not connected to the network, when the Printer tries to bind. When this occurs, the network number defaults to zero. No NDS trees were found on the Novell network. Check to see that the frame types on the Printer are properly configured.
Protocol Setup or Ser- You must first vice Setup (Network enable a netSetup) work port. Frame Type selection (Network Protocol Setup>IPX>SPX Setup) Invalid frame size. Warning! IPX network number is zero.
Enable NDS No NDS trees (Network Service found. Setup>PServer Setup > NDS Setup)

After this Setup screen:

Select NDS Tree (Network Service Setup>PServer Setup>NDS Setup)
Warning! Selecting a new NDS tree deletes Bindery setup.
You have previously connected the Printer to a different NDS tree. NetWise supports only a single NDS tree connection. To avoid a potential conflict with an existing tree connection (for example, if the connection was made through a NetWare 4.x server in emulation mode), all bindery settings will be deleted. If you choose OK, and choose Yes in the following message screen (Delete Bindery setup and continue?), bindery settings are deleted and have to be re-entered in Bindery Setup. To avoid deleting the bindery settings, press the Menu key, or select OK and choose No in the following message screen (Delete Bindery setup and continue?). Repeat NDS Setup without changing the NDS tree, or exit to Bindery Setup to review your current bindery settings. The chosen container contains no sub-containers or objects relevant to the current mode of navigation.

Novell error messages

Novell error:
220 Guest account not available

Cause:

The guest account, which you have chosen for initial login, has expired or has been disabled by the NetWare supervisor.
Suggested action or exit:
Enable a guest account on the NetWare server for the purpose of setup. Alternatively, log in to a different account. In the ENTER LOGIN NAME screen, change the default name (guest) to supervisor or another valid login name. When you are prompted for a password, enter the correct password for the account you named. Select a different login account or print server. The error screen exits to the File Server Login screen (if login to file server failed) or NetWare Print Server screen (if login to Print Server failed). Pressing the Menu button returns to the PServer Setup screen. Select a different login account. The error screen exits to the File Server Login screen. Pressing the Menu button returns to the PServer Setup screen. Select a different file server (or try to get someone else to log off). Pressing the Menu button returns to the PServer Setup screen
222 Unable to log in to server. Password has expired for login name 252 Unable to log in to server. Login does not exist. 255 Unable to connect to file server. File server is down or out of connections. nnn Notify IPX (Novell) Administrator.
The server has connected to a file server, but is unable to log in to the file server or print server because the password has expired for the login account name or the named print server. The server has connected to a file server, but is unable to log in to the server because the selected login account does not exist on the file server. The Novell file server is down or out of connections. This error occurs while the server is trying to connect to the requested file server.
Indicates other network errors when the Printer is already connected to a file server. Something unexpected has happened and the user generally cannot recover without intervention of the network administrator. Error #197 indicates that you have exceeded the number of login attempts permitted for this account on the NetWare file server. Error #255 usually indicates a hard failure.
Notify the Novell administrator and report the error number. The error screen exits to the PServer Setup screen.

Runtime error messages

See the User Guide for additional runtime error messages, including printer alerts to load media in trays or cassettes, and a Disk Full message. These messages are reported by the Printer Control Panel and Fiery WebSpooler. PostScript error reporting can be turned on as a print option from Mac OS applica-tions that use a PostScript Level 2 or PostScript 3 driver or by setting the PS Setup option Print to PS error to Yes. Check power and cable This message indicates that the interface cable between the Controller Board and the printer engine is not connected, or a print job is ready but the printer is not turned on. Printer not found TCP/IP or IPX networks Most failures to find a printer on the network are due to conflicting or missing name or address settings for the Printer. You must enter particular names in certain places. The required names are: TCP/IP host name (also known as the DNS name), which is defined by your organi-zation. Enter the host name as the Server Name on the Control Panel. Remote printer (internal machine) name. Use one of the following: print hold print_PRN-M hold_PRN-M NOTE: If your network environment includes a UNIX server, make sure the remote printer name does not include a hyphen or slash character.

TRITON III upper fuser rollers utilize a unique 3-coat system that blends PFA, FEP and PTFE coatings with additional resins to provide a highly specialized coating specifically developed for the copier roller industry. The key is the internally reinforced basecoat, which provides increased abrasion resistance (durability) without sacrificing excellent release properties. This 3-coat system provides a smoother finished surface than many standard systems, reducing the need to polish most thin-walled rollers, which can be susceptible to damage during polishing. TM TUF/SIL upper fuser rollers are manufactured with a layer of silicone rubber that effectively regulates heat flow to the toner, plus an outermost layer that consists of a specially blended TEFLON brand coating providing excellent toner release and abrasion-resistance. This combination ensures reduced toner offsetting and improved, more consistent copy quality under certain demanding machine usage conditions. These rollers provide a high-performance, cost-effective solution for selected machines required to consistently produce the best possible copy quality. TM MICROSLEEVE lower pressure rollers, with nonstick PFA sleeves 50, 70, or 100 microns in thickness, TM provide excellent wear-resistance for improved copy quality over an extended life. A-Series MICROSLEEVE lower pressure rollers are designed specifically for machines utilizing lower fuser cleaning rollers. Their unique surface texture reduces toner buildup and improves cleaning efficiency within the fuser station. All Katun fuser rollers are designed specifically for their intended applications and manufactured to exacting quality standards, ensuring their excellent performance and long life. Fuser Cleaning Roller Coating Technologies Katun has introduced unique fuser cleaning roller technologies for machines requiring efficient removal and absorption of excess toner and contaminants, as well as continuous silicone oil lubrication of critical fuser station parts. For many machines, the ideal parts combination for achieving optimum copy quality and maximum parts life includes a specially designed Katun fuser cleaning roller. FIBRA fuser cleaning rollers incorporate a uniform network of special fibers that aggressively remove excess toner and contaminants from the contacted surface. By efficiently depositing toner and contaminants beneath its outermost surface, the unique FIBRA network also helps maintain a continuous lubricative flow of silicone oil from the rollers internal tank to critical fuser station parts. TM FIBRA II fuser cleaning rollers incorporate a unique configuration of highly heat-resistant fibers to greatly enhance cleaning performance, especially in hostile fuser station environments. Efficient absorption of excess toner and contaminants, together with continuous silicone oil lubrication of critical fuser station parts, effectively reduce parts and service expenses associated with the fuser station. TEFLON is a registered trademark of E.I. DuPont de Nemours and Company used under license by Katun Corporation. Personalized Product Program Katun offers an extremely cost-effective way for office equipment dealers/distributors to ensure repeat business and strengthen relations with customers. The Personalized Product program enables dealers/distributors to provide highquality Katun Performance imaging supplies (toner bottles and cartridges for use in copiers, printers and facsimiles, inks and masters for use in digital duplicators, and thermal transfer ribbons for use in facsimiles) with their business name and /or logo, plus contact information, so end-users always know whom to call to reorder. For a one-time, nominal set-up fee, Katun designs and produces full-color labels to customer specifications and applies them to packaging at no extra charge. Only end-user-replaceable Katun Performance products are eligible under the program. Enrollment is simple and easy. Just complete the agreement form and submit it to your Katun sales representative or visit the Personalized Products page for more program and enrollment information.

Personalized Product Agreement
Customer Information Customer Number: Contact Name: Title: Customer agrees to:
Provide pertinent information, a scanable copy of your company logo, or other desired label artwork, and color specifications for the labels. Pay a one-time, nominal setup fee upon approval of the label design. (Ask your sales representative for details.) Order in full master carton quantities.
Email Address: Phone Number: Fax Number: Katun Representative:

Katun agrees to:

Create a personalized, full-color label design to your specifications, per the information provided on page two of this form, for a onetime, nominal setup fee and send a proof for approval within a minimum of 7 days of receipt of this agreement. Produce labels printed with the customers approved design on white label stock, and affix them over the Katun Perfomance logo* on copier toner, printer/fax toner cartridge, digital duplicator ink/master packaging. Ship initial order within one week after the customer approves their Personalized Product label proof. Reorders will also ship within one week.
Projected Personalized Product Purchases
Katun Part * Number OEM Line Product/Model Description Minimum Order Quantity Projected ** Monthly Order

P P P P P P

One master carton One master carton One master carton One master carton One master carton One master carton

Signature:

*Only Katun Performance products can be personalized. **The Personalized Product part number is the regular Katun Performance part number with a P added at the end. See the Katun catalog for master carton quantities. ***Projection only. You are not committed to ordering the quantity you list on this form. NOTE: Products with personalized labels cannot be returned to Katun for credit unless a valid warranty claim exists.
Please Also Complete Page 2
Personalized Toner Agreement
Information for Personalized Product Label Please list only the information you want to appear on your Personalized Product label. Company Name: Street Address: City: State/Province: Phone Number: Other: Label Artwork Postal Code: Fax Number:
Attach a copy of your company logo and/or any other requested graphic elements. Artwork may be full color or black and white. We prefer original-quality artwork 4 x 4 (50mm x 50mm) or larger, but will accept a business card or sheet of company letterhead. Please indicate your color preferences. In the space below, please indicate the color(s) you want to use for all text, your company logo, and any other graphic elements. If appropriate, please supply accurate samples to be matched or specify Pantone or PMS color numbers. NOTE: Your labels will be printed on a thermal-transfer printer at a resolution of 300 dpi. Therefore color photographs cannot be printed and some colors may be difficult to match precisely.

1067-5705-01

1075-5771-01

576216

113620670

1144-5752-01

576209

Fuser Roller Bearing

1144-5752-02

7832, CF 9001

1151-5610-02
Upper Fuser Roller Bushing DI 181, DI 250, DI 250 F, DI 350 EP 1052, EP 1054, EP 1083, EP 1085 EP 2010, EP 2030 Upper Fuser Roller Bearing DI 250, DI 350, DI 350 F

1165-5712-01

1203-5009-01
Various Applications AFR- 1 AFR- 2, F- 11, F- 12 AD- 3, AD- 5, AD- 8, AD- 9, AF- 5 AFR- 1000, AFR- 12, AFR- 13, AFR- 14 AFR- 16, AFR- 17, AFR- 7, AFR- 9, DF- 331 DF- 723, DF- 724, DI 30, DI 450, DI 470 DI 520, DI 550, DI 620, EP 1080, EP 1081 EP 2050, EP 3050, EP 4000, EP 4050 EP 4210, EP 4232, EP 4233, EP 5000 EP 5325, EP 5425, EP 6000, EP 6001 EP 8015, PF- 101, PF- 102, PF- 104 PF- 105, PF- 114, PF- 115, PF- 202 PF- 204, PF- 205, PF- 207, PF- 208, PF- 4D PF- 5D, PF- 7D AD- 3, AD- 5, AD- 8, AD- 9, AF- 5 AFR- 1000, AFR- 12, AFR- 13, AFR- 14 AFR- 16, AFR- 17, AFR- 7, AFR- 9, DF- 331 DF- 723, DF- 724, DI 30, DI 450, DI 470 DI 520, DI 550, DI 620, EP 1080, EP 1081 EP 2050, EP 3050, EP 4000, EP 4050 EP 4210, EP 4232, EP 4233, EP 5000 EP 5325, EP 5425, EP 6000, EP 6001 EP 8015, PF- 101, PF- 102, PF- 104 PF- 105, PF- 114, PF- 115, PF- 202 PF- 204, PF- 205, PF- 207, PF- 208, PF- 4D PF- 5D, PF- 7D 7723, 7823, 7832, 7915, 7920 8020, 8022, 8031, AF- 3, AF- 5 AFR- 1000, AFR- 12, AFR- 13, AFR- 14 AFR- 16, AFR- 17, AFR- 7, AFR- 9 BIZHUB C 350, BIZHUB C 351, BIZHUB C 450 CF 1501, CF 2001, CF 2002, CF 2203 CF 3102, CF 900, CF 9001, CF 910, DF- 331 DF- 723, DF- 724, DI 450, DI 470, DI 550 EDH- 1, EP 6000, EP 6001, EP 8010 EP 8015, EP 9765, FN- 107, FN- 108 FN- 109, FN- 110, FS- 133, FS- 134 S- 10 VI, S- 20 III, S- 20 IV, S- 20 V S- 20 VI, S- 202

1273-3516-01

12ZL75070

12ZL75080

1300-4342-03
EP 8605 EP 9765 Various Applications CF 80, DI 520, DI 620, EP 310, EP 4230 EP 4232, EP 4250, EP 4320, EP 450 EP 450 Z, EP 490 Z, EP 5400, EP 550 Z EP 570 Z, EP 6000, EP 6001, EP 650 Z EP 8010, EP 8015, EP 850, EP 8600, EP 8601 EP 8602, EP 870

1300-4342-04

Bearing EP 8605 Various Applications CF 80, EP 850, EP 8600, EP 8601, EP 8602 EP 870

4024-1004-01

4027-1359-01

4034-5622-01

7216, 7218, 7220, BIZHUB 180 BIZHUB 181, BIZHUB 210, BIZHUB 211, DI 1611 DI 1811 P, DI 2011 3231, 3240, 3331, 3340

40AA-2110

Drum Cleaning Blade Assembly Drum Cleaning Blade

4163-5602-02

7115, 7118, DI 152, DI 183

4402 039580

Upper Fuser Roller Cleaning Blade Drum Cleaning Blade

45AA-2250

4345, 4355

50GA-2090

BIZHUB 360, BIZHUB 361 BIZHUB 420, BIZHUB 421, BIZHUB 500 BIZHUB 501 2028, 2125, 3031, 3035, 3135 4045, 4145, 4155, 4255 7033, 7040, 7045

5400-2123

55GA56011

55VA56010

7075, DI 750

55WA20020

7050, 7050 P, 7055, 7060, 7155, 7165, 7255, 7272, DI 551 DI 5510, DI 650, DI 7210 7085, DI 850

56AA20100

56GA56010

57AA20080

BIZHUB 600, BIZHUB 601 BIZHUB 750, BIZHUB 751 BIZHUB PRO 920, BIZHUB PRO 950 ONDEMAND 92 7060

57GA56011

5A812270

BL 2460 D

DI 200 F, DI 250, DI 250 F DI 251, DI 251 F, DI 350, DI 350 F DI 351, DI 351 F

Corona/Charge/Transfer

1067-0759-01

Corona Wire 50 Oxidized

EP 2131, EP 2153 Charge Transfer EP 2120, EP 2121, EP 2130, EP 2150 EP 2151, EP 2152 All Applications EP 6000 Various Applications DI 181, DI 450, DI 470, DI 550 EP 5325 EP 5425 All Applications DI 30, EP 4210 EP 4211 Charge EP 3050, EP 4050, EP 4320, EP 5400

1075-0765-01

Corona Wire Cleaning Pads not included. 60 Corona Wire 50 Oxidized

1079-0760-01

1139-0756-01
EP 3010 All Applications EP 2050 Transfer, Separation EP 1052, EP 1054 EP 1080, EP 1081, EP 1083, EP 1085 EP 2010, EP 2030, EP 2051, EP 2080 EP 3050, EP 4000, EP 4050, EP 5000

1139-4261-01

Charge Corona Grid EP 3010 Various Applications EP 1052, EP 1054, EP 1080, EP 1081 EP 1083, EP 1085, EP 2010, EP 2030 EP 2051, EP 2080, EP 4000, EP 5000

1189002-010

375120
Corona Wire Spool 50 m / Spool 60 0.3 Gold Plated Charge Corona Grid

EP 303 W

25SA25081
Various Applications 7050, 7050 P 7055, 7060, 7065, 7150 Charge 7050, 7050 P 7075, 7085, DI 750, DI 850

8931-412

8935-215

8935-914

8936-214
EP 1054, EP 1085, EP 2030 EP 3010 7115, 7118, 7216, 7220, DI 152 DI 1611, DI 183, DI 2011, DI 2510 DI 2510 F, DI 3010, DI 3510, DI 3510 F DI 450, DI 550

8936-418

8936-914

8938-451

BIZHUB 222, BIZHUB 282 BIZHUB 362 100K BIZHUB 350 65K BIZHUB 200 80K BIZHUB 250

DV-310

Black Developer ORIGINAL Black Developer ORIGINAL 600 g / Bag
BIZHUB 200, BIZHUB 222 BIZHUB 250, BIZHUB 282, BIZHUB 350 BIZHUB 362 7022, 7130, 7135

PCUA 950-254

Electrical
BIZHUB C 250, BIZHUB C 300 BIZHUB C 300 ADV, BIZHUB C 350, BIZHUB C 351 BIZHUB C 352, BIZHUB C 352 ADV, BIZHUB C 450 DI 200 F, DI 250, DI 250 F, DI 251 DI 251 F, DI 350, DI 350 F, DI 351 DI 351 F, EP 2120, EP 2121, EP 2130 EP 2131, EP 2150, EP 2151, EP 2152 EP 2153, ONDEMAND SMB 35 C-3
Chip Reset Box 8020, 8031, BIZHUB C 350 Reset data not included BIZHUB C 351, BIZHUB C 450, CF 2002, CF 3102 with reset box Use of this product requires new OEM drum units for each model

Feed/Delivery

067640290

Paper Feed Belt

LT- 201, PF- 301, UBIX 404

1052-5222-01

Paper Pickup Roller Tire Only

CF 80, EP 4320, EP 5400

1054-5401-01
Paper Pickup Roller EP 4230, EP 4232, EP 4250 OEM uses Urethane Material Paper Feed Roller EP 4230 OEM uses Urethane Material Paper Pickup Roller Tire Only Paper Pickup/Feed Roller Tire Only Separation Pad EP 3170, EP 4210, EP 4211 EP 4233, EP 5325, EP 5425 C- 301, C- 302, C- 303, C- 304 C- 304 L, DI 520, DI 620, EP 6000, EP 6001 EP 8015 AFR- 14, AFR- 16, AFR- 17 DF- 331 AFR- 14, AFR- 16, AFR- 17 DF- 331 AFR- 14, AFR- 16, AFR- 17 DF- 331 DB- 431, DB- 432, PF- 106 PF- 116, PF- 117, PF- 120, PF- 121 DB- 431, DB- 432, PF- 116 PF- 117, PF- 120, PF- 121 7723, 7823, 7832, CF 900, CF 9001 CF 910, DI 450, DI 470, DI 550, EP 2050 EP 3050, EP 4000, EP 4050, EP 5000, MB- 1 EP 1080, EP 1081, EP 2050

1054-5428-01

1065-3061-01

1075-3051-01

111V-9310

111V51150

Paper Feed Roller

111V51160

Paper Takeup Roller

112E51220

Paper Feed Roller Tire Only Ribbed Tire Paper Pickup Roller Tire Only Ribbed Tire Bypass Upper Separation Roller Paper Pickup Roller Tire Only Paper Feed Roller Tire Only Takeup Roller Tire Only Original Pickup Roller Tire Only

112E51230

1136-0162-01

1139-3001-01

1151-3001-01
DI 181, EP 1052, EP 1054, EP 1083 EP 1085, EP 2010, EP 2030, EP 2051 DI 200 F, DI 250, DI 250 F DI 251, DI 251 F, DI 350, DI 350 F DI 351, DI 351 F AF- 5, AFR- 12, DF- 724

1164-3001-01

11UP45170

120A45820

65AA10430

Fuser Cleaning

1032-1701-01

636727

Wave Roller

EP 4320, EP 490 Z, EP 5400 EP 570 Z DI 520, DI 620, EP 6000, EP 6001 EP 8015, EP 850, EP 8600, EP 8601, EP 870 EP 3170, EP 4210, EP 4211 EP 4230, EP 4232, EP 4233, EP 4250 EP 6000, EP 8605, EP 9765

1051-1716-01

632305
Oil Supply Roller For use with mod. kit only. Oil Supply Roller

1054-1702-01

1074-5787-01

Web Supply Roller

1075-5751-01
Web Supply Pressure Roller DI 450, DI 470, DI 520, DI 550 DI 620, EP 6000, EP 6001, EP 8010 EP 8015 Web Supply Roller EP 5325, EP 5425

1076-5806-01

1136-5782-02
Oil Supply Roller EP 2050, EP 2051, EP 2080 FIBRA II EP 3050, EP 4000, EP 4050, EP 5000 Enhanced fuser cleaning efficiency. Oil Supply Roller EP 1050, EP 1052, EP 1080 EP 1081, EP 1083, EP 2010 7723, 7823, 7832, CF 900, CF 9001 CF 910 7723, 7823, 7832, CF 900, CF 9001 CF 910 DI 450, DI 470, DI 520, DI 550 DI 620, EP 6001, EP 8010, EP 8015 EP 1052, EP 1083, EP 2010 EP 2051, EP 2080 DI 250, DI 250 F, DI 350 DI 350 F EP 3010

1139-5525-01

1144-5797-01

Oil Application Roller

1144-5799-13

Oil Supply Roller

1145-5801-01

1151-5609-01

Lower Fuser Cleaning Roller Fuser Cleaning Roller

1164-5762-01

1173-5782-02

Fuser Cleaning Roller

1174-5609-01
DI 181, EP 1054, EP 1085, EP 2030 EP 3010 1015, 1020, 1120, 1212

25AA53251

25BA53393
2028, 2125, 3031, 3035, 3135 4045, 4145, 4155, 4255, 4345, 4355

25SA-5350

Oil Pad

7050, 7050 P

25SA53200
Upper Fuser Cleaning Roller Oil Supply Roller
7050, 7050 P, 7055, 7060, 7723, 7823, 7832, CF 900, CF 9001 CF 910 7723, 7823, 7832, CF 900, CF 9001 CF 910 1015, 1020, 1120, 1212

25TU54100

25TU54110

26AA53251

26NA53430
7020, 7022, 7025, 7030, 7145, 7222, 7228, 7235

26NA53432

26NA53830

PCUA 960-908

PK3-300

PM100-7033

100K Maintenance Kit 7033, 7040, 7045 Contains: (1) Drum Cleaning Blade (1) Fuser Cleaning Roller (1) Fuser Roller Cleaning Pad (1) Charge Wire Cleaning Block Assembly C (1) Charge Wire Cleaning Block (1) Charge Wire Cleaning Block Assembly A (2) Corona Wire (1) Corona Wire (1) Oil Application Roller (1) Toner Filter (1) Charge Corona Grid PM Kit 7135 Contains: (2) Heat Insulating Sleeve A (1) Heat Insulating Sleeve B (1) Lower Pressure Roller (1) Upper Fuser Roller (1) Cover Assembly (1) Suction Filter and Assembly PM Kit 7145 Contains: (2) Heat Insulating Sleeve A (1) Heat Insulating Sleeve B (1) Lower Pressure Roller (1) Upper Fuser Roller (1) Cover Assembly (1) Suction Filter and Assembly (1) Fuser Idler Gear

9351-2010-41

Exposure Lamp 160V 260W Exposure Lamp 160V 240W Exposure Lamp 160V 280W Exposure Lamp 162V 235W Control Panel Lamp Assembly
EP 3170, EP 4210, EP 4211

9351-2610-21

EP 1052, EP 1054, EP 1083 EP 1085, EP 2010, EP 2030 EP 4230, EP 4232, EP 4250

9351-2821-01

9351-2821-52
EP 4320, EP 5325, EP 5400 EP 5425 EP 4000, EP 5000, EP 6001 EP 8015

Miscellaneous

DUC Chip Black
BIZHUB C 250, BIZHUB C 252

DUC Chip Cyan

DUC Chip Magenta

DUC Chip Yellow

BIZHUB C 300, BIZHUB C 300 ADV BIZHUB C 352, BIZHUB C 352 ADV ONDEMAND SMB 35 C-3 BIZHUB C 300, BIZHUB C 300 ADV BIZHUB C 352, BIZHUB C 352 ADV ONDEMAND SMB 35 C-3 BIZHUB C 300, BIZHUB C 300 ADV BIZHUB C 352, BIZHUB C 352 ADV ONDEMAND SMB 35 C-3 BIZHUB C 300, BIZHUB C 300 ADV BIZHUB C 352, BIZHUB C 352 ADV ONDEMAND SMB 35 C-3 BIZHUB C 451, BIZHUB C 550 BIZHUB C 650 BIZHUB C 451, BIZHUB C 550 BIZHUB C 650 BIZHUB C 451, BIZHUB C 550 BIZHUB C 650 BIZHUB C 451, BIZHUB C 550 BIZHUB C 650 BIZHUB C 350
BIZHUB C 350, BIZHUB C 351 BIZHUB C 450 BIZHUB C 350, BIZHUB C 351 BIZHUB C 450 BIZHUB C 350, BIZHUB C 351 BIZHUB C 450

Photoreceptors

OPC Drum 7033, 7040, Boxes per Master Carton OPC Drum 6 Boxes per Master Carton 7723, 7823, CF 900, CF 910

8937-906

8937-907

8937-908

8937-909

8937-920

Yellow Toner 8020, 8031, CF 2002, CF 3102 KATUN ACCESS 230 g / Cartridge Packaged for use in Konica Minolta 4 Boxes per Master Carton Yellow Toner ORIGINAL 230 g / Cartridge CF 2002, CF 3102

8937-921

Magenta Toner 8020, 8031, CF 2002, CF 3102 KATUN ACCESS 230 g / Cartridge Packaged for use in Konica Minolta 4 Boxes per Master Carton Magenta Toner ORIGINAL 230 g / Cartridge CF 2002, CF 3102

8937-922

Cyan Toner 8020, 8031, CF 2002, CF 3102 KATUN ACCESS 230 g / Cartridge Packaged for use in Konica Minolta 4 Boxes per Master Carton Cyan Toner ORIGINAL 230 g / Cartridge CF 2002, CF 3102

8938-404

Black Toner BIZHUB 350, BIZHUB 362 Equivalent to TN311 Packaged for use in Konica Minolta 15 Cartridges per Master Carton Black Toner BIZHUB 200, BIZHUB g / Cartridge BIZHUB 250, BIZHUB 282 Equivalent to TN-211 Packaged for use in Konica Minolta 15 Boxes per Master Carton Black Toner ORIGINAL BIZHUB 200, BIZHUB 222 BIZHUB 250, BIZHUB 282

8938-415

8938-509
Black Toner Cartridge BIZHUB C 250, BIZHUB C g / Cartridge Includes replacement ozone filter Packaged for use in Konica Minolta 4 Boxes per Master Carton Black Toner Cartridge ORIGINAL 430 g / Cartridge BIZHUB C 250, BIZHUB C 252

8938-510

Yellow Toner Cartridge BIZHUB C 250, BIZHUB C g / Cartridge Packaged for use in Konica Minolta 4 Boxes per Master Carton Yellow Toner Cartridge ORIGINAL 260 g / Cartridge BIZHUB C 250, BIZHUB C 252

8938-511

Magenta Toner Cartridge BIZHUB C 250, BIZHUB C g / Cartridge Packaged for use in Konica Minolta 4 Boxes per Master Carton Magenta Toner Cartridge ORIGINAL 260 g / Cartridge BIZHUB C 250, BIZHUB C 252

8938-512

Cyan Toner Cartridge BIZHUB C 250, BIZHUB C g / Cartridge Packaged for use in Konica Minolta 4 Boxes per Master Carton Cyan Toner Cartridge ORIGINAL 260 g / Cartridge BIZHUB C 250, BIZHUB C 252

8938-705

Black Toner Cartridge BIZHUB C 300, BIZHUB C 300 ADV 430 g / Cartridge BIZHUB C 352, BIZHUB C 352 ADV Equivalent to TN312K ONDEMAND SMB 35 C-3 Includes replacement ozone filter Packaged for use in Konica Minolta 4 Boxes per Master Carton Black Toner Cartridge ORIGINAL Genuine Konica Minolta Brand BIZHUB C 300, BIZHUB C 300 ADV BIZHUB C 352, BIZHUB C 352 ADV ONDEMAND SMB 35 C-3

8938-706

Yellow Toner Cartridge BIZHUB C 300, BIZHUB C 300 ADV 260 g / Cartridge BIZHUB C 352, BIZHUB C 352 ADV Equivalent to TN312Y ONDEMAND SMB 35 C-3 Packaged for use in Konica Minolta 4 Boxes per Master Carton Yellow Toner Cartridge ORIGINAL Genuine Konica Minolta Brand BIZHUB C 300, BIZHUB C 300 ADV BIZHUB C 352, BIZHUB C 352 ADV ONDEMAND SMB 35 C-3

A0D7154

A0D7251

A0D7252

A0D7254

A0D7351

A0D7352

A0D7354

A0D7451

A0D7452

A0D7454

PCUA 950-251

PCUA 950-280
Black Toner 7115, 7118, 7216, 7218, g / Cartridge DI 1811 P Packaged for use in Konica 6 Boxes (12 Cartridges) per Master Carton Black Toner 7218, DI 152, DI 1611, DI 1811 P 413 g / Cartridge DI 183, DI 2011 Equivalent to 105A, 105B Packaged for use in Minolta 6 Boxes (12 Cartridges) per Master Carton Black Toner 7135, 7235 KATUN ACCESS 676 g / Cartridge Equivalent to TN303K Packaged for use in Konica Minolta 12 Boxes (12 Cartridges) per Master Carton Black Toner ORIGINAL 676 g / Cartridge Black Toner 1040 g / Cartridge Packaged for use in Konica 8 Boxes per Master Carton Black Toner 1300 g / Cartridge Packaged for use in Konica 8 Boxes per Master Carton 7135, 7235

PCUA 950-367

PCUA 950-564

7155, 7165, 7255, 7272

PCUA 950-638

PCUA 960-420

Black Toner 7145 KATUN ACCESS 676 g / Cartridge Equivalent to TN401K Packaged for use in Konica Minolta 12 Boxes (12 Cartridges) per Master Carton Black Toner 8020, 8031, CF 2002, CF 3102 KATUN ACCESS 230 g / Cartridge Packaged for use in Konica Minolta 4 Boxes per Master Carton Yellow Toner 8020, 8031, CF 2002, CF 3102 KATUN ACCESS 230 g / Cartridge Packaged for use in Konica Minolta 4 Boxes per Master Carton Magenta Toner 8020, 8031, CF 2002, CF 3102 KATUN ACCESS 230 g / Cartridge Packaged for use in Konica Minolta 4 Boxes per Master Carton Cyan Toner 8020, 8031, CF 2002, CF 3102 KATUN ACCESS 230 g / Cartridge Packaged for use in Konica Minolta 4 Boxes per Master Carton

PCUA 960-846

PCUA 960-847

PCUA 960-848

PCUA 960-849

TN-211

Black Toner BIZHUB 200, BIZHUB g / Cartridge BIZHUB 250, BIZHUB 282 Equivalent to TN-211 Packaged for use in Konica Minolta 15 Boxes per Master Carton Black Toner ORIGINAL BIZHUB 200, BIZHUB 222 BIZHUB 250, BIZHUB 282

TN-214C

Cyan Toner Cartridge BIZHUB C 200 ORIGINAL 18,500 Yield Genuine Konica Minolta Brand 12 Boxes per Master Carton Black Toner Cartridge BIZHUB C 200 ORIGINAL 24,000 Yield Genuine Konica Minolta Brand 8 Boxes per Master Carton Magenta Toner Cartridge BIZHUB C 200 ORIGINAL 18,500 Yield Genuine Konica Minolta Brand 12 Boxes per Master Carton Yellow Toner Cartridge BIZHUB C 200 ORIGINAL 18,500 Yield Genuine Konica Minolta Brand 12 Boxes per Master Carton Black Toner BIZHUB 350, BIZHUB 362 Equivalent to TN311 Packaged for use in Konica Minolta 15 Cartridges per Master Carton Black Toner 676 g / Cartridge Packaged for use in Konica Minolta 6 Boxes per Master Carton Black Toner ORIGINAL BIZHUB 360, BIZHUB 361 BIZHUB 420, BIZHUB 421, BIZHUB 500 BIZHUB 501

Lower Picker Finger Wave Roller Drum Cleaning Blade Drum Cleaning Blade KATUN ACCESS Oil Supply Roller Upper Fuser Roller Lower Pressure Roller Upper Picker Finger Paper Pickup Roller Drum Cleaning Blade KATUN ACCESS Oil Supply Roller Upper Picker Finger Paper Pickup Roller Paper Feed Roller Paper Pickup Roller Lower Fuser Roller Bearing OPC Drum Corona Wire Upper Fuser Roller Lower Pressure Roller Lower Fuser Roller Bearing Picker Finger
1049-0105-01 1051-1716-01
1052-1701-03 1052-1710-01 1052-4701-01
1052-5222-01 1053-0149-01 1054-1702-01
1054-4753-01 1054-5401-01
1065-3061-01 1065-5871-01
1067-0293-01 1067-0759-01
1067-5705-01 1067-5710-01
1074-0155-02 1074-0156-01 1074-0293-01 1074-0904-01 1074-5701-01 1074-5787-01 1075-0296-01 1075-0296-01 1075-0765-01 1075-0902-01 1075-3051-01 1075-5751-01 1075-5757-01 1075-5768-01 1075-5771-01 1076-5802-01 1076-5806-01 1079-0760-01
Drum Cleaning Blade Toner Anti-Spill Blade OPC Drum Drum Cleaning Blade Upper Picker Finger Web Supply Roller OPC Drum OPC Drum KATUN ACCESS Corona Wire Drum Cleaning Blade Paper Pickup/Feed Roller Web Supply Pressure Roller Lower Picker Finger Upper Fuser Roller Upper Fuser Roller Bearing Upper Fuser Roller Web Supply Roller Corona Wire Toner Collection Bottle Separation Pad Paper Feed Roller Paper Takeup Roller Lower Pressure Roller KATUN ACCESS
111V-9310 111V51150 111V51160 1129-2021-01
Paper Feed Roller Paper Pickup Roller Drum Cleaning Blade Upper Fuser Roller OPC Drum OPC Drum Bypass Upper Separation Roller Drum Cleaning Blade Lower Pressure Roller Oil Supply Roller Bearing OPC Drum OPC Drum KATUN ACCESS Corona Wire Paper Pickup Roller Charge Corona Grid Lower Pressure Roller Oil Supply Roller Upper Fuser Roller Drum Cleaning Blade Drum Cleaning Blade KATUN ACCESS Toner Anti-Spill Blade OPC Drum
1132-5543-01 1132-5701-01
1134-0296-01 1135-0296-01 1136-0162-01
1136-0901-01 1136-5779-01

1136-5782-02 113620670

1139-0292-01 1139-0292-01 1139-0756-01 1139-3001-01 1139-4261-01
1139-5522-01 1139-5525-01 1139-5562-01 1139-5711-17 1139-5711-17 1139-5726-01 1144-0294
1144-5513-02 1144-5746-04
Drum Cleaning Blade Upper Fuser Roller Lower Pressure Roller Fuser Roller Bearing Fuser Roller Bearing Oil Application Roller Oil Supply Roller Web Supply Roller OPC Drum Paper Feed Roller Upper Fuser Roller Lower Fuser Cleaning Roller Upper Fuser Roller Bushing OPC Drum OPC Drum Upper Fuser Roller Lower Pressure Roller OPC Drum OPC Drum Drum Cleaning Blade Lower Pressure Roller OPC Drum OPC Drum KATUN ACCESS

4408-0751-01 4425-3009-01 4426-3128-02 4426-3128-02
4469-3504-01 4474-0217-04 4474-3505-01 4490-3504-01 4490-3505-02 4496-3001-02
450075020 4518-601 4519-601 454053391

576233 34304

Bearing Black Imaging Unit ORIGINAL Yellow Imaging Unit ORIGINAL Magenta Imaging Unit ORIGINAL Cyan Imaging Unit ORIGINAL Drum Cleaning Blade Lower Pressure Roller Imaging Unit ORIGINAL Separation Pad Upper Fuser Roller Toner Collection Bottle Toner Collection Bottle Ozone Filter Assembly Upper Fuser Roller Lower Pressure Roller Lower Pressure Roller Lower Fuser Roller Bearing Lower Pressure Roller Lower Pressure Roller Upper Fuser Roller Bearing Drum Cleaning Blade
4587-403 4587-503 4587-603 4587-703 45AA-2250
4601-300 4652-0752-01 466053010

490010170 490053050

4969-1043-01 504053040

508053141 508053150

Upper Fuser Roller Lower Pressure Roller Upper Fuser Roller Drum Cleaning Blade Lower Pressure Roller Paper Feed Tire Upper Fuser Roller Upper Fuser Roller KATUN ACCESS Cleaning Web Ozone Filter 2 Ozone Filter 1 Toner Filter Bearing Lower Pressure Roller Oil Pad Corona Wire Upper Fuser Roller Lower Pressure Roller Charge Corona Grid Corona Wire Upper Fuser Roller Lower Pressure Roller Oil Application Roller
552053032 55FA-5350 55FA25012 55FA53193 55FA53200 55GA25071 55GA26071 55GA53031 55GA53042 55GA53110
55GA53121 55GA53502 55GA56011 55GA75020 55VA-4830
Fuser Cleaning Roller Fuser Roller Cleaning Pad Drum Cleaning Blade Upper Fuser Roller Bearing Feed/Double Feed Prevention Roller Assy Paper Feed Roller Assembly Cleaning Web Assembly Lower Pressure Roller Assembly Charge Corona Grid Upper Fuser Roller Fuser Auxiliary Roller Lower Fuser Cleaning Roller Drum Cleaning Blade Drum Cleaning Blade Reverse Roller Assembly Paper Feed Roller Assembly Cleaning Web Assembly Cleaning Web Assembly Drum Cleaning Blade Corona Wire Corona Wire Upper Fuser Roller Lower Pressure Roller
55VA-5242 55VA-5281 55VA25080 55VA53041 55VA53070
55VA53860 55VA56010 55WA20020
56AA-4080 56AA-4690 56AA-5430 56AA-5431 56AA20100 56AA25090
Upper Picker Finger Upper Fuser Roller Lower Pressure Roller Assembly Drum Cleaning Blade Upper Fuser Roller Upper Fuser Roller Drum Cleaning Blade Cleaning Web Assembly Lower Pressure Roller Cleaning Web Assembly Drum Cleaning Blade Upper Fuser Roller Drum Cleaning Blade Bearing Ozone Filter Exit Roller Upper Fuser Roller Lower Pressure Roller Toner Collection Bottle Corona Wire Spool Black Toner Black Toner KATUN ACCESS Black Toner
56GA-5280 56GA56010 56GB53040 576053010

57AE-5430 57AE53060

60912270 65AA10430
65AA49050 65AA53010 65AA53020 65FA51050

74669000 84522

Black Toner KATUN ACCESS Black Toner Black Toner Black Toner KATUN ACCESS Black Developer ORIGINAL Black Toner KATUN ACCESS Black Toner Black Toner Black Toner Black Toner Black Toner ORIGINAL Black Toner Black Developer ORIGINAL Black Toner Black Toner Black Toner KATUN ACCESS Black Toner Black Developer ORIGINAL Black Toner KATUN ACCESS Black Developer ORIGINAL Black Toner Black Toner ORIGINAL Black Toner

(a) Technical Evaluation/ Replacement or technical Evaluation/ Credit: Ship the product and the completed form to: Katun (E.D.C.) B.V. Edisonweg HG Gorinchem The Netherlands (b) Automatic Replacement: send the completed form to your customer service representative.
DISTRIBUTOR CHOICE WARRANTY CLAIM FORM
Please print all information. For prompt processing of your claim, please complete all sections. Your feedback is important to the ongoing improvement of Katun products. Thank you. I. WARRANTY CHOICE Please check one. See Section 2 on reverse side for additional information. Technical Evaluation/Replacement II. CUSTOMER INFORMATION Customer Number: Company Name: Address: City: Country Your Name: III. PRODUCT INFORMATION Katun PN 1) 2) 3) 4) 5) IV. DETAILED REASON(S) FOR CLAIM Provide specific information for each product claimed, explaining the reason for claim in as much detail as possible. Include machine models, machine log information, and copy/print counts. See Section 3 on reverse side for additional specific requirements for photoreceptors. 1) 2) 3) 4) 5) FOR KATUN USE ONLY Product Warranty Claim No.: Received By Pieces: Date: Quantity Description Serial/Lot Number State/Province: Postal Code: Title: Date Shipped: Delivery Date: Technical Evaluation/Credit Automatic Replacement
PLEASE READ AND COMPLY WITH ALL THESE REQUIREMENTS TO EXPEDITE THE PROCESSING OF YOUR CLAIM. 1. General Instructions
A completed copy of this form must accompany all product warranty claims. Please indicate date of product delivery for determination of warranty coverage time period. Your feedback is important to the ongoing improvement of Katun products. Please complete all sections on the reverse side.
2. Distributor Choice Warranty Claim Options
Please indicate your choice of Technical Evaluation/Replacement, Technical Evaluation/Credit, or Automatic Replacement. NOTE: Automatic Replacement claims must be filed within 90 days of product delivery date, and must not exceed US$500/550. If no choice is indicated: (a) If product is included with this form, this claim will be treated as Technical Evaluation/Replacement. (b) If no product is included with this form, and the claim is less than US$500/550, this claim will be treated as Automatic Replacement. (c) If no product is included with this form, and the claim is more than US$500/550, the claim is invalid.

3. Specific Requirements

If damage (for example, a chip or scratch on a photoreceptor) is noted out-of-box, DO NOT INSTALL THE PRODUCT. No copy/print samples are required. Installing a product with out-of-box damage could void the warranty. Include applicable copy/print samples with all claims. If a photoreceptor is suspected to be defective after machine installation, please attach to this form the copy/print samples indicated below. This will allow a thorough evaluation of the claim. Ensure that neither the form nor copy/print samples will contact the photoreceptor surface during shipment. FOR PHOTORECEPTORS USED IN COPIERS, include: (a) Three sky shot (open platen; black) copies; (b) Three white copies; and (c) Three copies of a test pattern. NOTE: If the defect is not visible on the copies indicated above, please attach three copies which clearly show the defect. FOR PHOTORECEPTORS USED IN PRINTERS AND PLAIN PAPER FACSIMILES, include three prints which clearly show the defect. IMPORTANT: The Katun product warranty does not cover damage by operator, technician, or machine (including rotational scratches, gouges, scuff marks, or line scratches).

4. Shipping Instructions

ALL PRODUCT RETURNS MUST BE PROPERLY PACKAGED. This includes packaging in the correct individual product box and in a second container with adequate protective packaging material. This is required by all carriers. NOTE: Products damaged in transit to Katun due to inadequate packaging cannot be covered by the Katun product warranty, and will be returned. Ship Technical Evaluation claims, freight prepaid, to the address specifically indicated for this purpose in the General Information section of the Katun On-Line Catalogue and current printed catalogues. Katun cannot accept responsibility for product warranty claims sent to any other address. Send Automatic Replacement Claims to your Katun Customer Service Representative.