INSTALLATION MANUAL

FS-601

Finisher

for Product Code 4036
NOTES Before installing, be sure to unplug the power cord of the machine. Keep all packing materials out of the reach of children.

4583-7761-01

Printed in Japan
FS-601 I Outline of Installation Procedures for 4036 System
When installing the machine and associated options as a system, follow the order shown on the left. DK-501 NOTE For the detailed installation procedures for each option, follow the instructions given in the corresponding Installation Manual and perform the procedures correctly.

PC-101

PC-201

PC-401

Dehumidifier Heater 1C

Copier/Printer Machine

Electron System Options Electron System Options AD-501 EM-301

FS-501

HD-501

JS-601

PK-501/PK-4/ PK131

EK-501

VI-501

DF-601

OC-501

DT-105

4583U004AA

WT-501

FS-601 I Before Installing the Finisher
In order to adjust the height of the machine to the height of the finisher, the Paper Feed Cabinet PC-101, or PC-201, or PC-401, or Desk must be installed. <Machine + Paper Feed Cabinet PC-101/PC201>

I Unpacking the Finisher

1. Check that the following accessories are available in the box. 1 Rail guide A....Rail guide B....Ground plate...Rail....Positioning pin...Magnet plate...Horizontal transport unit...Exit tray...Staple cartridge...Screw A...4 <Machine + Paper Feed Cabinet PC-401> 11 Screw B...Screw C...Screw D...Spacer....Label....1 * 16 Installation Manual (this manual)...1 Rail Guide A is not used when the FS-601 is mounted on the machine (product code 4036). 5

4583U005AA

4583U006AA

<Machine + Desk>

4698U044AA

4684U061AB

4684U062AA

4698U045AB

4698U046AB

4583U007AA

4698U047AA

4698U048AA

4698U049AA

4698U100AA

4698U051AA

9735U001AA

4583U018AA
2. Remove protective tape and packing materials from different parts of the finisher. Tape
I Installing the Accessories
1. Peel off the seal covering the area where the stabilizing pin and magnet plate will be attached.

4583U016AA

2. Attach the enclosed stabilizing pin and magnet plate with the enclosed screws C to the left side of the machine as shown.
4698U055AB 4698U105AA 4583U013AA
3. Place the Ground Plate furnished with the kit in Rail Guide B.

4583U015AA 4684U063AB

4583U014AA
4. Attach the Rail guide B to the bottom left part of the machine (two screws D furnished with the finisher). NOTE Fit Rail Guide B in the tab on the lower portion of the Paper Feed Unit.

4698U101AA 4684U064AA

FS-601 I Installing the Horizontal Transport Unit
1. Remove the protective tape.

I Installing the Rail

1. Insert the rail into the Rail guide B. 2. Protrude the leading edge of the rail out about 60 mm to the right from the right end of the machine. NOTE If the rail is pulled out more than necessary, it is caught by the flat spring fitted to the machine as it is brought back into the original position. 3. Insert the spacer furnished with the finisher into the rail. NOTE Slide out the rail to the left and check that it does not come off the Rail guide B.

C4651U023AB

4584U065AA
2. Mate the attaching portion of the horizontal transport unit with the mounting bracket at the finisher entrance section.

C4683U023AA

3. Press the horizontal transport unit up against the rear side. NOTE Make sure that the gear on the finisher and that on the horizontal transport unit are in positive mesh with each other.

C4683U014AA

4583U017AB
4. Place the horizontal transport unit on the exit section of the machine.
4. With the horizontal transport unit kept in a level position, fit the lock lever into position. 5. Gently swing the horizontal transport unit down to the finisher side.

4583U008AA

C4683U013AA
5. Secure the finisher rail in position using screw B (one screw).
I Adjusting Height and Correct Alignment
1. Gently move the finisher toward the machine and check for following. Is the positioning pin aligned with the hole in the finisher? Does the horizontal transport unit run excessively slantwise? Does the clearance at A equal that at B? A

4698U057AA

I Installing the Exit Tray

4583U009AA 4583U010AA

If the finisher is not at the same height as the machine, adjust the machine as follows. 2. Slide the finisher away from the machine and remove the caster covers (at two places).

4583U012AA

2. Hook the mounting hooks of the exit tray onto the catches provided on the finisher exit section.

4698U062AA

3. Remove the adjusting screw covers (at four places).

4698U058AA

3. Using screws A (four screws), secure the exit tray into position.

4698U063AA

4698U059AA
4. Loosen the two caster fixing screws (at four places).
I Installing the Staple Cartridge
1. Open the front door and slide out the staple unit. 2. Remove the staple cartridge from its protective bag. 3. Insert the staple cartridge into position until a click is heard. 4. Close the front door.

4698U064AA

4698U099AA

4698U102AA

5. Turn the adjusting screw to make the adjustment. To raise the finisher, turn the adjusting screw counterclockwise. To lower the finisher, turn the adjusting screw clockwise.

4698U065AA

I Connecting the Hookup Cord
1. Remove the connector covers from the horizontal transport unit and the machine. 2. Connect the hookup cord to the horizontal transport unit and the machine.
6. Tighten the caster fixing screws. 7. Reinstall the caster covers and adjusting screw covers.

4583U011AA

FS-601 I Adjusting the Staple Position and Fold Position

<Adjusting Center-Staple Position> Machine equipped with an AFR 1. Load the drawer with A3L paper. 2. Select the functions as follows: Orig Copy4in1/BookletBookletBind. L L 7. Display the Tech. Rep. Mode screen. (For details of how to display the Tech. Rep. Mode screen, see the Service Manual.) 8. Touch Machine Adjust.
3. Load a 5-page A3L document (blank sheets of paper may be used) in the document feeding tray. * Use a 5-page document to minimize variations. 4. Press the Start key. * From here on, follow procedures starting with step 7 onward given on the right-hand half of this page. Machine not equipped with AFR 1. Load the drawer with A3L paper. 2. Select the functions as follows: Orig Copy4in1/BookletBookletBind.

4036P031CA

9. Touch Center Binding Position.

4036P036CA

3. Place an A3L original (a blank sheet of paper may be used) on the original glass. 4. Press the Start key five times (to let the machine scan the original five times). * Use a 5-page set to minimize variations. 5. Touch Finish. 6. Press the Start key. * From here on, follow procedures starting with step 7 onward given on the right-hand half of this page.

4698P027CA

10. Touch Center-Staple Position.
11. Fold the copy set fed out of the machine in half. * Call the copy page facing up A and the that facing down B.
12. Check for any deviation between the stapled position and the newly folded crease. NOTE Use the newly folded crease, not the machine-folded one, for the check. Standard: mm <Decrease the value toward the - end.> A B

4698U068AA

Machine not equipped with AFR 1. Display the basic screen. 2. Select the functions as follows: Orig Copy4in1/BookletBookletBind. L

<Reference> A B

4698U069AA
<Increase the value toward the + end.> A B

4698U070AA

3. Place an A3L original (a blank sheet of paper may be used) on the original glass. 4. Press the Start key five times (to let the machine scan the original five times). * Use a 5-page set to minimize variations. 5. Touch Finish. 6. Press the Start key. * From here on, follow procedures starting with step 7 onward given below. 7. Display the Tech. Rep. Mode screen. (For details of how to display the Tech. Rep. Mode screen, see the Service Manual.) 8. Touch Machine Adjust.
13. Use the or key to make the adjustment. If the staple is on the side of A, decrease the value toward the - end. If the staple is on the side of B, increase the value toward the + end. 14. Touch END. 15. Make the copy and check again.
<Adjusting Fold-Position> Machine equipped with an AFR 1. Display the basic screen. 2. Select the functions as follows: Orig Copy4in1/BookletBookletBind. L

3. Load a 5-page A3L document (blank sheets of paper may be used) in the document feeding tray. * Use a 5-page document to minimize variations. 4. Press the Start key. * From here on, follow procedures starting with step 7 onward given on the right-hand half of this page.
FS-601 I Affixing the Labels
10. Touch Fold-Position. Affix the labels to the position shown below. B A

4698P028CA

11. Check for any deviation between the stapled position and the folded crease. * Call the copy page facing up A and the that facing down B. Standard: mm <Increase the value toward the + end.> A B

4698U112AA

4698U110AA

4698U109AA

<Decrease the value toward the - end.> A A

4698U113AA

12. Use the or key to make the adjustment. If the staple is on the side of A, increase the value toward the + end. If the staple is on the side of B, decrease the value toward the - end.

4698U107AA

13. Touch END. 14. Make the copy and check again.

INSTALLATION MANUAL

FS-501

Finisher

for Product Code 4036
NOTES Before installing, be sure to unplug the power cord of the machine. Keep all packing materials out of the reach of children.

4684-7761-01

Printed in Japan
FS-501 I Outline of Installation Procedures for 4036 System
When installing the machine and associated options as a system, follow the order shown on the left. DK-501 NOTE For the detailed installation procedures for each option, follow the instructions given in the corresponding Installation Manual and perform the procedures correctly.

PC-101

PC-201

PC-401

Dehumidifier Heater 1C

Copier/Printer Machine

Electron System Options Electron System Options AD-501 EM-301

FS-601

HD-501

JS-601

PK-501/PK-4/ PK131

EK-501

VI-501

DF-601

OC-501

DT-105

4684U057AB

WT-501

FS-501 I Before Installing the Finisher
In order to adjust the height of the machine to the height of the finisher, the Paper Feed Cabinet PC-101, or PC-201, or PC-401, or Desk must be installed. <Machine + Paper Feed Cabinet PC-101/PC201>

I Unpacking the Finisher

1. Check that the following accessories are available in the box. 1 Rail guide A....Rail guide B....Ground plate...Rail....Stabilizing pin....Magnet plate...Horizontal transport unit...Tray....1

4684U058AA

9 Protective guide...1 <Machine + Paper Feed Cabinet PC-401> 10 Label....Screws A...Screws B...Installation manual (this manual)...1 * 14 Spacer....1 Rail Guide A is not used when the FS-501 is mounted on the machine (product code 4036). 1 <Machine + Desk> 4 5

4684U059AA

4698U044AA

4684U061AB

4684U062AA

4698U045AB

4698U046AB
4684U060AA 4698U047AA 4698U048AA 4684U075AA 4684U070AA

4684U076AA

4684U072AA

9735U001AA

4583U018AA
2. Remove all tape and packing brackets. Tape NOTES Make sure that the installation site is flat and level. After the Finisher has been set up, avoid moving it unless it is absolutely necessary. When the Finisher needs to be moved, perform the steps by referring to Removing the Rail on p. 7. After the Finisher has been moved, perform the steps given in Installing the Horizontal Transport Unit on p. 5 and step 5, 6 on p. 4.

Packing bracket

C4683U006AB

4684U074AA

NOTE Do not remove these parts.

C4683U008AA

4643U003AA

C4683U005AA

FS-501 I Installing the Accessories
1. Peel off the seal covering the area where the stabilizing pin and magnet plate will be attached. 5. Insert the rail into the Rail Guide B. 6. Protrude the leading edge of the rail out about 60 mm to the right from the right end of the machine. NOTE If the rail is pulled out more than necessary, it is caught by the flat spring fitted to the machine as it is brought back into the original position.

4583U016AA

4684U065AA
2. Attach the enclosed stabilizing pin and magnet plate with the enclosed screws A to the left side of the machine as shown.
7. Insert the spacer that comes with the finisher into the rail. NOTE Slide out the rail to the left and check that it does not come off the Rail Guide B. 8. Slide the other end of the rail installed in step 5 into the rail guide on the finisher. NOTE Insert the rail until it snaps into place. At this time, the finisher should stay attached to the machine, even if you try to pull it away.

C4683U009AA

4583U017AB
3. Place the Ground Plate furnished with the kit in Rail Guide B.

4684U063AB C4683U010AA

4. Attach the rail guide B to the left side of the Paper Feed Unit as shown in the illustration (two screws B furnished with the finisher). NOTE Fit Rail Guide B in the tab on the lower portion of the Paper Feed Unit.

4684U064AA C4683U011AA

FS-501 I Unpacking the Horizontal Transport Unit
Remove all packing materials and tape.
I Adjusting the Height and Tilt of the Finisher

1. If the finisher gradually tilts toward the machine, check the following: Are the stabilizing pin and the hole in the finisher at the same height? Is the horizontal transport unit not extremely tilted? *

4684U066AA

C4651U023AB
I Installing the Horizontal Transport Unit
1. Place the horizontal transport unit on the paper output section of the machine, and make sure that the plastic guide pin on the bottom of the horizontal transport unit hooks into the bracket on the finisher.
If the finisher is not at the same height as the machine, adjust the machine as follows.
2. Slide the finisher away from the machine, and then remove the lower-front cover (two screws) of the finisher.

C4683U023AA 4643U021AB

2. Push the horizontal transport unit in. NOTE Make sure that the gears on the horizontal transport unit and on the finisher are correctly aligned. 3. Lift the finishers two caster covers up, and then pull them off.

C4683U014AA

3. Secure the horizontal transport unit with the lock. NOTE Firmly secure the Horizontal Transport Unit and the Finisher in position using the Lock Lever.

C4683U013AA

4643U020AA
FS-501 I Connecting the Hookup Cord
Securing bolt Adjusting bolt 4. Without turning the adjusting bolt (lower bolt) on the caster, loosen the securing bolt (upper bolt), and then turn the adjusting bolt (lower bolt) as indicated below to adjust the height of the finisher. <Two rear casters> If the stabilizing pin is too high: Turn the bolt clockwise If the stabilizing pin is too low: Turn the bolt counterclockwise <Two front casters> If the magnet plate is too high: Turn the bolt clockwise If the magnet plate is too low: Turn the bolt counterclockwise

4684U069AA

1. Remove the connector covers from the horizontal transport unit and the machine. 2. Connect the hookup cord to the horizontal transport unit and the machine.

4684U068AA

4643U022AB
3. Secure the hookup cord of the Horizontal Transport Unit using the cord clamp (large) of the finisher.
5. If the finisher tilts toward the machine, check the following: a Are distances a and b equal? b *

4684U067AA

If a and b are not equal, refer to step 4 above and turn the adjusting bolt (lower bolt) as indicated to adjust the tilt of the finisher.
Securing bolt Adjusting bolt
6. After the adjustment is finished, without turning any of the adjusting bolts (lower bolts), tighten the four securing bolts (upper bolts). 7. Re-install the caster covers and the lowerfront cover (two screws).

4643U029AA

FS-501 I Installing the Tray and Protective Guide
Install the enclosed tray and protective guide at the positions shown in the illustrations.

I Affixing the Labels

Affixing the enclosed operation labels. Label for Machine Label for RADF
4643U024AA C4683U018BA 4698U109AA

for Machine

for RADF

4643U017AA

I Removing the Rail
1. Pinch together the rail stoppers on the left side of the finisher to release them. 2. Disconnect the two hookup cords. 3. Remove the horizontal transport unit from the finisher, and then place it on top of the machine. 4. Carefully pull the finisher away from the machine. 5. Slide the rail under the machine, and then remove it from the right side of the machine.

C4651U020AA