The approach that is suggested here is sure to get you to your desired result.
Here you can see what has to be done.
This is a helpful tip Text passages that are identified in this manner provide you with tips and tricks that make it even easier to work with the printer.

Overview of the printer

External features

No. 5 6

Description Top cover release button Manual feed tray Power switch (ON/OFF) Face-down tray (printed side down) Control panel Top cover

No. 11 12

Description Paper guides for manual feed tray Tray1 (multipurpose tray) USB interface connector Parallel interface connector Face-up/face-down selection switch (printed side up/down) Power cord socket

Inside the printer

No. 1 2
Description Fusing unit Toner cartridge
Description Drum cartridge
Installing and setting up the printer Optional accessories
Description Face-up tray (printed side up)
Description Lower feeder unit (Tray 2) (500-sheet capacity)

Printer control panel

The control panel has two indicators and one button.
No. 3 Description Error indicator (orange) Ready indicator (green) Panel button
For further information on the control panel, see chapter 6.
Installing your laser printer
Place of installation Set up the printer in a place that is

q q q q q q q q q q q

dry and free from dust on a stable surface well ventilated near an easily accessible power socket away from objects which might obstruct the printers ventilation grille away from highly flammable items (such as curtains) away from splashing liquids away from organic gases (such as ammonia) away from direct sunlight away from severe temperature fluctuations away from exhaust-air from heating, ventilation, and air-conditioning systems
Storage of consumables and accessories Printing consumables and accessories should be kept
sealed in their original packaging protected from direct sunlight or heat protected from fluorescent light in a cool, dry, and dust-free place out of reach of children

For technical specifications of the cable, see chapter 10.
Note Using the wrong type of cable can damage the socket on the printer. - Use only an IEEE 1284 type B shielded interface cable.
Installing and setting up the printer USB interface
Note Windows 95/NT4.0 do not support USB connections.
1 Turn off both the PC and the printer. 2 Turn on the PC. 3 Turn on the printer. 4 When Windows and the printer are both ready, connect one end of the
interface cable to the PCs USB port.
5 Connect the other end of the
interface cable to the USB interface connector on the back of the printer. operating ? Does the Windowsnew device? system detect the
Plug-and-play driver installation should start automatically. Follow the instructions on the screen. See chapter 3 for more information. If plug-and-play driver installation doesnt start automatically, leave the printer on, unplug both ends of the interface cable, and the reconnect the cable. If this does not work, use the instructions in chapter 3 to install the printer driver manually.
Note Using the wrong type of cable can damage the socket on the printer. - Use only a USB Revision 1.1 compliant cable for connecting the printer to your computer.
Minimum system requirements
IBM-compatible PC with a Pentium/Celeron series, AMD K6/Athron/ Duron family or compatible 200 MHz processor (300 MHz recommended) Windows XP/Me/2000/98/95/NT 4.MB RAM (Windows 98/95/NT 4.0), 32 MB RAM (Windows Me), 64 MB RAM (Windows 2000), or 128 MB RAM (Windows XP) 36 MB free hard disk space (20 MB for printer driver and status display, 16 MB for image processing) IEEE 1284 Type B parallel port or USB Revision 1.1 port CD-ROM drive
Notes on installing the printer driver
The installation program is designed so that even people not accustomed to working with computers can easily install a printer driver. You will be led step-by-step through the installation process. All you need to do is follow the installation program. Before you begin the installation, you should know the following information:

q q q q

What operating system is running on your computer (for example, Windows XP)? What is the letter of your CD-ROM drive (for example, D)? Which optional accessories are installed on your printer (for example, a lower feeder unit)? Is your printer connected directly to your computer via a parallel interface cable or a USB cable?

11 This completes the installation of the USB device driver for the
MINOLTA-QMS PagePro 1200W printer. Now go to the following section to install the printer driver. To install the printer driver using the Installer under Windows Me The CD-ROM that came with your printer starts automatically after being loaded into the CD-ROM drive of your PC. You are guided step-by-step through the installation procedure.
1 With Windows running, insert the CD-ROM that came with your printer
into your PCs CD-ROM drive. The installation program starts automatically.
Browse the CD-ROM and double-click setup.exe to start the installation program.
the installation of the printer driver. To install the printer driver using Plug-and-Play under Windows Me For a simple way of installing the printer driver, we recommend using the Installer (see the previous section). However, there are other ways of installing the printer driver without using the installer. This section describes Plug-and-Play installation with a parallel connection.
1 After connecting the printer to your PC with the parallel cable, turn on
2 Turn on the PC. After Windows starts, the Add New Hardware Wizard

dialog displays.

3 Insert the CD-ROM that came with your printer into your PCs CDROM drive, click the Specify the location of the driver (Advanced) button, and then choose [Next].
4 Choose the Search for the best driver for your device.
(Recommended). option button, check the Specify a location: box, and then choose [Browse].
5 Browse the CD-ROM and navigate to \Drivers\language\Win9x. 6 Choose [OK], and then choose [Next] twice. 7 Follow the instructions on the screen to complete the installation. 8 Check that the MINOLTA-QMS PagePro 1200W printer icon is
displayed in the Printers dialog box.
9 Remove the CD-ROM from your PCs CD-ROM drive. This completes
the installation of the printer driver. To install the printer driver using the Add Printer Wizard under Windows Me
3 Choose[Start], point to Settings, and then choose Printers. 4 Double-click the Add Printer icon.
5 Choose [Next]. 6 Select Local Printer. 7 Choose [Next]. 8 Choose [Have Disk], and then choose [Browse].
9 Browse the CD-ROM and navigate to \Drivers\language\Win9x. 10 Choose [OK]. 11 Choose [OK], and then choose [Next]. 12 Select the appropriate port, and then choose Next.
If you are using a parallel connection, select LPTx: (x=1, 2, etc.). If you are using a USB connection, select USB001:
13 Follow the instructions on the screen to complete the installation. 14 Check that the MINOLTA-QMS PagePro 1200W printer icon is

2 Turn on the PC. After Windows starts, the Update Device Driver
Wizard dialog box displays.
4 Choose [Other Locations], and then choose [Browse]. 5 Browse the CD-ROM and navigate to \Drivers\language\Win9x. 6 Choose [OK]. 7 Follow the instructions on the screen to complete the installation.
8 Check that the MINOLTA-QMS PagePro 1200W printer icon is 9 Remove the CD-ROM from your PCs CD-ROM drive. This completes
the installation of the printer driver. To install the printer driver using the Add Printer Wizard under Windows 95
5 Choose [Next]. 6 Select Local Printer. 7 Choose [Next]. 8 Choose [Have Disk], and then choose [Browse]. 9 Browse the CD-ROM and navigate to \Drivers\language\Win9x. 10 Choose [OK] twice, and then choose [Next]. 11 Follow the instructions on the screen to complete the installation
12 Check that the MINOLTA-QMS PagePro 1200W printer icon is
13 Remove the CD-ROM from your PCs CD-ROM drive. This completes
Installing the printer driver under Windows NT 4.0
To install the printer driver using the Installer under Windows NT 4.0 The CD-ROM that came with your printer starts automatically after being loaded into the CD-ROM drive of your PC. You are guided step-by-step through the installation procedure.
the installation of the printer driver. To install the printer driver using the Add Printer Wizard under Windows NT 4.0 For a simple way of installing the printer driver, we recommend using the Installer (see the previous section). However, there are other ways of installing the printer driver without using the Installer. This section describes Plug-and-Play installation with a parallel connection. Windows NT 4.0 does not support USB connections.
3 Choose [Start], point to Settings, and then choose Printers.
4 Double-click the Add Printer icon.
5 Select My Computer. 6 Choose [Next]. 7 Select the appropriate port and then choose[Next]. 8 Choose [Have Disk.], and then choose [Browse.]. 9 Browse the CD-ROM and navigate to \Drivers\language\WinNT4. 10 Choose [Open]. 11 Choose [OK], and then choose [Next]. 12 Follow the instructions on the screen to complete the installation. 13 Check that the MINOLTA-QMS PagePro 1200W printer icon is
14 Remove the CD-ROM from your PCs CD-ROM drive. This completes
Uninstalling the printer driver and USB device driver
This section describes how to uninstall the PagePro 1200W printer driver when necessary.
Note If the uninstallation program is used to remove the printer driver, the USB device driver is also removed.
Note If you used Add Printer to install the printer driver, there is no uninstaller utility. To remove the printer, select it and delete it in the Printers folder.
Note The screen images that appear in this section show the examples of uninstallation under Windows 98. Your screen may differ slightly. To uninstall the printer driver under Windows XP

Printers directory.

2 Select the MINOLTA-QMS PagePro 1200W printer icon.
3 Display the printer driver settings:
Windows Me/98/95From the File menu choose Properties, and then choose the --> 32-bit Driver Setup tab.
The operating system also uses tabs! The General and Details tabs are automatically determined by the operating system and are therefore not described in this manual.
Windows 2000From the File menu choose Printing Preferences. The following window displays.
Windows NT 4.0From the File menu choose Document Defaults. A window similar to the Windows 2000 window shown above displays.

4.2 Setup tab

The Setup tab allows you to

q q q q q q q q

Print several pages of a document on the same page (n-up printing) Provide a watermark on printed documents Design custom watermarks Specify manual duplex printing Specify paper feed from different trays Define the type of paper/media Print using a form overlay Create/edit a form overlay
Refer to the printer drivers online help for information on all of these functions.

Paper tab

The Paper tab allows you to

q q q q q q q q q

Specify the size of the original document Define custom media sizes Fit printed documents to a specified media size Select the output media size Scale (enlarge/reduce) documents Specify the number of copies Turn on/off the printers sorting function Turn on/off the Proof Print function Specify the orientation of the media

4.4 Quality tab

The Quality tab allows you to
Specify the resolution Adjust the contrast and brightness of the printed document Turn on/off Toner Save mode
Device Options Setting tab
The Device Options Setting tab allows you to
Activate the optional lower feeder unit (Tray 2) View information about the printer driver.
If you used the CD-ROM Installer to install the printer driver, the Status Display was also installed. It was not installed, however, if you used Add Printer to install the printer driver.

Environment

The Status Monitor and Printer Control Panel can be used with the following operating systems and interfaces.
IEEE 1284 Parallel Windows XP Windows Me Windows 2000 Windows 98 SE Windows 98 Windows 95 Windows NT 4.USB
5.2 Opening the Status Display
Use one of the following steps to open the Status Monitor.
Windows Me2000//98/95/NT 4.0From the Start menu, choose Programs, then MINOLTA-QMS PagePro 1200W Utilities, and then MINOLTA-QMS PagePro 1200W Status. Windows XPChoose Start, choose All Programs, then MINOLTAQMS PagePro 1200W Utilities, and then MINOLTA-QMS PagePro 1200W Status.

Which sizes of paper can I use?
This printer is designed for use only with these media sizes.
Media source Tray 1 Tray 2*(optional) Manual feed tray
Media size Standard sizes Letter 8.5" x 11.0" Legal 8.5" x 14.0" Executive 7.25" x 10.5" Half Letter 5.5" x 8.5" Ax 297 mm Ax 210 mm B5 JIS 182 x 257 mm Chinese 16K 185 x 260 mm Chinese 32K 130 x 185 mm
Yes Yes Yes Yes Yes Yes Yes Yes Yes
Yes Yes Yes No Yes No Yes No No
Envelopes, postcard and custom sizes Envelope Monarch 3.875" x 7.5" Envelope COM10 4.125" x 9.5" Envelope DL 110 x 220 mm Envelope Cx 229 mm Envelope Cx 162 mm Envelope Bx 250 mm Choukei-3Gou 120 x 235 mm Choukei-4Gou 90 x 205 mm Postcard 100 x 148 mm Custom 3.0" 8.5" x 5.0"14.0" (mm x mm) Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes No No No No No No No No No No Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes
* The optional lower feeder unit (Tray 2 is shipped with either a letter or A4 tray. Legal and executive/B5 JIS trays are available as optional accessories.
Working with the printer What types of paper can I use? This printer is designed for use with the following media types.
Media source Media type Tray 1 Plain paper 1624 lbs (6090 g/m2) Thick paper/Labels 2443.25 lbs (90163 g/m2) Envelopes Letterhead Postcard Transparencies Yes Yes Yes Yes Yes Yes Tray 2 (optional) Yes No No No No No
Manual feed tray Yes Yes Yes Yes Yes Yes

Printable area

0.2" (4 mm) 0.2" (4 mm)

0.2" (4 mm)

6.2 Using the panel button
No. Description Error indicator (orange) Ready indicator (green) No. 3 Description Panel button
The panel button allows you to
Continue a print job after an error message Cancel a print job
Continuing a print job after an error message You can continue the print job after correcting the following types of errors:
When the print job is too complex and the memory capacity of the printer is inadequate When there is no more paper in the trays When paper of a different format than that set in the printer driver was fed into the printer
1 Check that one of the above errors has occurred. 2 Press the panel button to operate the media feed.

The print job continues.

Check your printed document! If you have continued a print job after an error message, be sure to check your printed document. Not all pages may have printed.

Be sure to use both hands whenever you are inserting the tray into or removing it from the lower feeder unit.
7 Reconnect the power cord and interface cable, and turn on the printer.
Installing the face-up tray
The printer is fitted with a tray for face-down output. A tray for face-up output is available as an option. This tray is especially useful for thick paper, envelopes, labels, and transparencies because the path through the printer is straighter. The face-up tray can hold up to 20 sheets. Before installing the face-up tray:
1 Remove the face-up output tray from its carton. 2 Attach the face-up output tray by inserting the pins into the holes on the printer, one side at a time. Do not force both sides in at the same time.
The face-up tray must be bent slightly to insert it.
Face-up or face-down output? You can set the output direction with the output switch. (For details see chapter 6.)
CAUTION You could damage the unit by using incorrect accessories and parts! If you use accessories and parts from manufacturers other than MINOLTA-QMS, we cannot guarantee that the laser printer will operate properly.
Use only MINOLTA-QMS accessories and parts unless specified otherwise.
8.1 Replacing the toner cartridge
Replace the toner cartridge when it is empty or when the printed documents are too light. Two toner cartridges are available:
The regular toner cartridge has a capacity of about 3000 letter/A4 pages at about 5% toner coverage. The high-capacity toner cartridge has a capacity of about 6000 letter/ A4 pages at about 5% toner coverage.
Note: The toner cartridge that comes with the printer has a capacity of about 1500 letter/A4 pages at about 5% toner coverage.
WARNING The fusing unit can become very hot! The fusing unit, which is located beneath the top cover, can become very hot when the printer is in operation.
To prevent injuries, avoid contact with this area.

Fusing unit

What precautions should I take when handling the toner cartridge? Never touch the developing roller under the flap; otherwise, print quality may decline.
1 Turn off the printer and disconnect the power cord from the printer. 2 Close the face-down tray. 3 Press the top cover release button

and open the top cover.

4 Remove the old toner cartridge.
5 Press in the marked positions of the
handle to fold down the handle.
Dispose of the used toner cartridge properly.
6 Remove the new toner cartridge

from its package.

7 Holding it firmly with both hands,
rock the toner cartridge left and right, forward and backward, to distribute the toner evenly.
8 Completely remove the protective
seal from the toner cartridge, and then raise up the handle.
9 Holding the handle, lower the toner
cartridge into the printer, aligning the four pins (two on each side) fit into the grooves inside the printer.
Color coordinated 2 labels have been affixed to the toner cartridge and to the inside of the printer. Install the toner cartridge by aligning these labels.
The toner cartridge clicks into place when it is completely installed.
10 Close the top cover and press it
down gently but firmly until it locks into place.
Resetting the counter for the toner cartridge After you have replaced the toner cartridge, reset the counter for the toner cartridge.
1 Turn off the printer. 2 While holding down the panel button, turn on the printer.
The green Ready indicator begins to blink.
3 Continue holding down the panel button, and the green Ready indicator starts to blink. 8-5
lease the panel button. Both indicators begin to blink.
4 After the green Ready indicator has blinked for about 5 seconds, re-
5 After confirming that both indicators are blinking, press and hold down
the panel button again for at least 5 seconds. Both indicators light up for about 5 seconds, and then both indicators begin to blink again. The counter for the toner cartridge has now been reset.
6 Turn the printer off and then on again.
Once the green Ready indicator remains on, the printer is again in Stand-by mode.
Replacing the drum cartridge
Change the drum cartridge when the printed documents become faint or blurred. The drum cartridge has a capacity of about 16,000 (one-page jobs) to 20,000 (continuous printing) letter/A4 pages (at an average of 5% or less coverage).

What precautions should I take when handling the drum cartridge? Never touch the drum under the flap; otherwise, print quality may decline.
4 Remove the toner cartridge and the

old drum cartridge.

5 Remove the new drum cartridge from its carton. 6 Install the drum cartridge in the
printer, aligning the guides of the cartridge with the grooves inside the printer.
Color coordinated 1 labels have been affixed to the drum cartridge and to the inside of the printer. Install the drum cartridge by aligning these labels.
7 Place the toner cartridge back into
the printer, aligning the four pins (two on each side) with the grooves inside the printer.
The cartridge will click into place when it is completely installed.
8 Close the top cover and press it
Resetting the counter for the drum cartridge
After you have replaced the drum cartridge, reset the drum cartridge counter.
3 Continue holding down the panel button, and the green Ready indicator starts to blink.
4 After the green Ready indicator has blinked for about 5 seconds, release the panel button. Both indicators begin to blink.
5 After confirming that both indicators are blinking, briefly press the
panel button. Both indicators light up for about 5 seconds, and then both indicators begin to blink. The counter for the drum cartridge has now been reset.

Cleaning the printer

Clean the printer at regular intervals to prevent dust, dirt, and paper residue from accumulating in and on the printer. Cleaning the outside of the printer
1 Turn off the printer and disconnect the power cord from the printer. 2 Wipe the outside of the printer with a soft cloth. You may moisten the
cloth with a little neutral household cleaner if you wish.
Maintaining the printer Cleaning the paper feed roller Clean the paper feed roller if paper feed problems occur frequently.
To prevent injuries, avoid contact with this area. After turning off the printer, wait at least 10 minutes before cleaning the inside of the printer.
drum cartridge. Wrap the drum cartridge with a cloth to protect it from exposure to light.

5 Wipe the paper feed roller with a

soft, dry cloth.

6 Reinstall the drum cartridge and the

toner cartridge.

7 Close the top cover and press it
Note Some computers connected with the parallel cable may not be able to communicate correctly with the printer.
CAUTION The fusing unit can become very hot! The fusing unit, which is located beneath the top cover, can become very hot when the printer is in operation.

Clearing media jams

Clearing a paper misfeed inside of the printer
1 Turn off the printer. 2 Close the face-down tray.
3 Press the top cover release button,
and then open the top cover.

drum cartridge.

5 Carefully pull the misfed media out

of the printer.

If paper is misfed at the fusing unit, grasp the bottom of the paper with both hands and gently pull it out.
6 Reinstall the drum cartridge. 7 Reinstall the toner cartridge. 8 Close the top cover, and then open the face-down tray.
Printing automatically restarts from the page that was misfed.
Clearing a media jam in the output tray
1 Carefully pull the misfed media out

of the tray.

2 Open the top cover and close it again in order to reset the printer.
Troubleshooting Clearing a media jam at Tray 1
1 Remove the tray cover and any

media in Tray 1.

2 Carefully pull the misfed media out

of Tray 1.

3 Reload the media in Tray 1, and replace the tray cover.
Do not reload curled or wrinkled media.
4 Reinstall Tray 1 in the printer. 5 Close the face-down tray, and then open the top cover. 6 Remove any pieces of media that may have torn off or are remaining

in the printer.

7 Close the top cover, and then open the face-down tray. 8 Open the top cover and close it again in order to reset the printer.
Clearing a media jam in the manual feed tray
1 Remove the Tray 1 cover and the
plate at the inlet of the manual feed tray.
2 Remove the misfed media.

Black pages
The toner cartridge is damaged.
Remove the toner cartridge and check for damage. If necessary, replace the toner cartridge. (See page 8-2.)

Pages are too light

The Toner Save mode has been activated.
Check the setting in the printer driver. Change the setting and try printing again. (See chapter 4.) Set the toner density to the desired level and try printing again. (See chapter 8.) Remove the toner cartridge and rock it in order to improve the distribution of the remaining toner. If the problem persists, replace the toner cartridge. (See chapter 8.) Remove the toner cartridge and check it for damage. If necessary, replace the toner cartridge. (See chapter 8.)
The toner density is not set correctly in the printer driver. The toner cartridge may be running out of toner.
Problem Pages are too dark Possible cause The toner cartridge is damaged. Action
Remove the toner cartridge and check it for damage. If necessary, replace the toner cartridge. (See chapter 8.) Set the toner density to the desired level. (See chapter 4.)
The toner density is not set correctly in the printer driver.
Blurred background on the printout

Uneven toner density

Remove the toner cartridge and check for damage. If necessary, replace the toner cartridge. (See page 8-2.) Remove the drum cartridge and check for damage. If necessary, replace the drum cartridge. (See page 8-6.) Remove the toner cartridge and gently rock in order to improve the distribution of the remaining toner. If the problem persists, replace the toner cartridge. (See page 8-2.) Replace the paper you are using with dry paper and try printing again.
The drum cartridge is damaged.
The toner may be unevenly distributed inside the toner cartridge.
Blank spots, text missing
The paper is moist because of high humidity in the air or from being splashed with water.
Possible cause The toner cartridge is damaged (white lines). Action Remove the toner cartridge and check for damage. If necessary, replace the toner cartridge.(See page 8-2.) Remove the drum cartridge and check for damage. If necessary, replace the drum cartridge. (See page 8-6.)
Problem White or black lines
The drum cartridge is damaged (black lines).

Toner smudges

Remove the toner cartridge and check for damage. If necessary, replace the toner cartridge. (See page 8-2.) Remove the toner cartridge and gently rock in order to improve the distribution of the remaining toner. If the problem persists, replace the toner cartridge. (See page 8-2.) Clean the paper feed roller. (See page 8-11.)
The paper feed roller is dirty.

Printer messages

Indicator functions The control panel has two indicators and one button. The control panel indicators provide information on the status of the printer.

Please read the next section before using this device. It contains important information related to user safety and preventing equipment problems. Make sure you observe all of the precautions listed in this manual. * Note that some parts of the contents of this section may not correspond with the purchased product.
Warning and precaution symbols
Ignoring this warning could cause serious injury or even death.
Ignoring this caution could cause injury or damage to property.

Meaning of symbols

A triangle indicates a danger against which you should take precaution. This symbol warns against cause burn.
A diagonal line indicates a prohibited course of action. This symbol warns against dismantling the device.
A black circle indicates an imperative course of action. This symbol indicates you must unplug the device.
Do not modify this product, as a fire, electrical shock, or breakdown could result. If the product employs a laser, the laser beam source could cause blindness. Do not attempt to remove the covers and panels which have been fixed to the product. Some products have a high-voltage part or a laser beam source inside that could cause an electrical shock or blindness. Only use the power cord supplied in the package. Failure to use this cord could result in a fire or electrical shock. Use only the specified power source voltage. Failure to do that could result in a fire or electrical shock. Do not use a multiple outlet adapter to connect any other appliances or machines. Use of a power outlet for more than the marked current value could result in a fire or electrical shock. Do not unplug and plug in the power cord with a wet hand, as an electrical shock could result.
Plug the power cord all the way into the power outlet. Failure to do this could result in a fire or electrical shock.
Do not scratch, abrade, place a heavy object on, heat, twist, bend, pull on, or damage the power cord. Use of a damaged power cord (exposed core wire, broken wire, etc.) could result in a fire or breakdown. Should any of these conditions be found, immediately turn OFF the power switch, unplug the power cord from the power outlet, and then call your authorized service representative. In principle, do not use an extension cord. Use of an extension cord could cause a fire or electrical shock. Contact your authorized service representative if an extension cord is required. Do not place a flower vase or other container that contains water, or metal clips or other small metallic objects on this product. Spilled water or metallic objects dropped inside the product could result in a fire, electrical shock, or break-down. Should a piece of metal, water, or any other similar foreign matter get inside the product, immediately turn OFF the power switch, unplug the power cord from the power outlet, and then call your authorized service representative. If this product becomes inordinately hot or emits smoke, or unusual odor or noise, immediately turn OFF the power switch, unplug the power cord from the power outlet, and then call your authorized service representative. If you keep on using it as is, a fire or electrical shock could result. If this product has been dropped or its cover damaged, immediately turn OFF the power switch, unplug the power cord from the power outlet, and then call your authorized service representative. If you keep on using it as is, a fire or electrical shock could result. Do not throw the toner cartridge or toner into an open flame. The hot toner may scatter and cause burns or other damage.

VARNING! Om apparaten anvnds p annat stt n i denna bruksanvisning specificerats, kan anvndaren utsttas fr osynlig laserstrlning, som verskrider grnsen fr laserklass 1. Det hr r en halvledarlaser. Den maximala effekten fr laserdioden r 5 mW och vglngden r nm. VARO! Avattaessa ja suojalukitus ohitettaessa oletPP alttiina nkymttmlle lasersteilylle. l katso steeseen. VARNING! Osynlig laserstrlning nr denna del r ppnad och sprren r urkopplad. Betrakta ej strlen. Ozone release During printer operation, a small quantity of ozone is released. This amount is not large enough to harm anyone adversely. However, be sure the room where the machine is being used has adequate ventilation, especially if you are printing a high volume of materials, or if the machine is being used continuously over a long period. Dgagement dozone Limprimante dgage une faible quantit dozone durant son utilisation. Cette quantit nest pas suffisamment importante pour tre dangereuse. Cependant, veillez ce que la pice dans laquelle la machine soit adquatement ventile, surtout en cas dimpression de gros volumes ou en cas dutilisation continue pendant un laps de temps trs long.

11 Index A

Accessories see Optional accessories...7-1 Add Printer...3-2
Button see Panel button...6-4
Cleaning the printer...8-10 paper feed roller...8-11 Connecting the printer...2-12 Consumables storage...2-5 Control panel button see Panel button...6-4 Control panel indicators Error....6-4 Ready...6-4
Envelopes....6-1 Error indicator...6-4 Error messages...9-12
Face-down output...6-7 Face-down tray... 2-1, 6-7 Face-up output...6-7 Face-up tray...6-7
Installing.... 3-21 Installing the printer.... 2-5

Jam see Media jam... 9-7

Loading envelopes... 6-1 Loading paper... 6-1 lower feeder unit... 6-6 manual feed tray...2-8, 6-6 Tray 1...2-7, 6-5 Tray 2.... 6-6
Maintenance.... 8-1 Media jam inside of the printer.. 9-1 lower feeder unit... 9-7 manual feed tray... 9-6 output tray... 9-4 Media type list... 6-3 Messages error messages... 9-12 service.... 9-13 status... 9-12
Optional accessories face-up tray... 7-3 Lower feeder unit... 7-1 storage... 2-5 Output face-down... 6-7 face-up... 6-7 Overview of printer... 2-1 control panel.... 2-4 11-2

WFU* jOAM - b U WOc d WFUD w UNF{ o w WHB b X bFUOJOUu qB l b w jzU UM X O WFUD qGA w b; jzUu r w QD U b wD iO iO jzU pUA uH uKF UDG WUG

ld iO UM

QHD QHD QHD
QD) WU Q hd wM q s tOB sJ1 b QD v WUd c dOA qOuU qB WKJA* dL WOU UNKG r WFUD n WUd c dN Q Wb e0
tKF V U UNKG r WFUD n WKJA* dL WOU WOMH ue Wb qB WFUD WU QD) dR vUId dOD QD ld iO WuN' dR dC QHD

oK* . W UH u

W dOUF wJd d w d X 5B d FCC part 15 subpart B class B wJd d w OUMGdNJ oUD dOUF ICES-003 wJd d EMC EU Directive 89/336/EEC w d EN 55022 (CISPR Pub.22) class B wJd d EN 61000-3-2 wJd d EN 61000-3-3 wJd d GB 9254 class B 5B d AS/NZS 3548 class B UOd d
UL 60950, CSA C22.2 No. 60950 EU Directive 73/23/EEC EU Directive 93/68/EE EN60950 (IEC 60950).///////////// GB4943..

. WOMH UH u*

d u q YU d s d u UO u s bQK YU d s QON www.minolta-qms.com/products l u* v V
eO lA0 WOJ WFU U u 0 duB wJOUdJ UE lKC wUJF ` eO UL wzUdN duB WU UE Wd nB (dpi) W uWOzu{ WDI (dpi) W uWOzu{ WDI A4vK u/wuU WIOUH dpi vK A4 u/wuU WIOWH dpi vK A4 u/wuU WOU dpi vK A4 u/wuU WOU dpi vK WUD dO u WGOB wu q u uM WFUD UE dF UE duD UE u{u WFUD Wd

WUD D WOL X

JIS, B5, A4, A5 ,wuU nB buKU u/ wuU u WKBH WU& U A4, A5, JIS B5 ,wMO 32KwMO Monarch, DL, C5, C6,B5 WU& nUE Choukei-3Gou, Choukei-4Gou Postcard.. UJu

u jzUu U

ld q v U nzUH nUE ld q v pOL nUE U WbO WcG UO vKH WcG b W qH tu b W WbO WcG W UO vKH WcG b

uU WcG

W qH tu W UO vK tu Wu W v XUNdN W v WU U Wu XUNdN W bI VKI WU U bI VKI v d iO v u W M lD A4 u/wuU W M lD A4 wuU d d iO v u edO Xu edO Xu q Xu q Xu
d WF qOGA bM d( qOGA bM Wud WOuD Wud u 0 Wud WOzUdNJ WUD WUD N
q dO [ Xu Amperage WdO q dO [ Xu rK W u [ UH qH tu WOU) UF_ rK W u [ d oKG rK [ oL mK UdI q [ WFUD u mK [ UdI q [ WOuD Wud) mK [ UdI q [ u Wud (Compatible/Nibble/ECP) u IEEE 1284 jd WKO
USB (REVISION 1.1 compliant) Naltec N1 chip CPU Wed* W'UF* b
XOUGO vKH WcG b vKH WcG bu B5 JIScOHM wuUI uK vK tu

WOUOI dc UO

UO vKH WcG b
A4 u/ wuU wUO B5 JIScOHM wuUI uK WUO
u jzUuu WF WOU) UF_ WKF b
ld q U W v rK W u [ UH rK W u [ d rK W u [ oL mK UdI q [

Wu* jd WKO u

u u q u WFUD u EIA q u duOLJ eF iQ U q q V

IEEE 1284, B u q u

qJ u ub hOB

(USB) wK

B wK K fU A wK K fU

K qUM j WKO u

u qJ u ub hOB
WFUD duOLJ WeF WuH UUO u VKD
1:V BUS MMMMMM 2: D+ NNNNN 3: D- MMMMM 4: GND N NNN Shell: Shield,,,,,,,,