KRU PS

Espresso

NOVO 2000

Model#984
Instruction Book Warranty

Guarantee of Performance

IMPORTANT SAFEGUARDS
When using electrical appliances, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and/or injury to persons, including the following: 0 Read all instructions and information in this instruction book and any other literature included in this carton referring to this product before operating or using this appliance. 0 Do not touch hot surfaces. Use handles or knobs. 0 To protect against fire, electric shock and personal injury do not immerse cord, plugs, or appliance in water or other liquid. 0 Close supervision is necessary when any appliance is used by or near children. 0 Unplug from outlet when not in use and before cleaning. Allow to cool before putting on or taking off parts, and before cleaning the appliance. 0 Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions, or has been damaged in any manner. Return appliance to your nearest authorized KRUPS Service Center for examination, repair or adjustment, or call KRUPS Consumer Service Department (see GUARANTEE OF PERFORMANCE) for repair procedure. 0 The use of accessory attachments not recommended or sold by KRUPS may result in fire, electric shock or personal injury. 0 Do not use outdoors. l.Do not let cord hang over edge of table or counter, or touch hot surfaces. 0 Do not place on or near a hot gas or electric burner, or in a heated oven. 0 Always attach plug to appliance first, then plug cord into the wall outlet. To disconnect, turn any control to off, then remove plug from wall outlet. 0 This appliance is for household use only. Any servicing other than cleaning should be performed by your local authorized KRUPS Service Center. 0 Use extreme caution when disposing hot steam.

SAVE THESE INSTRUCTIONS

CAUTION
This appliance is for household use. Any servicing other, than cleaning and user maintenance should be performed by an authorized service representative. 0 Do not immerse appliance in water or try to disassemble. 0 To reduce the risk of fire or electric shock, do not remove the base. No user serviceable parts inside. Repair should be done by authorized service personnel only. l Check voltage to be sure that the voltage indicated on the name plate agrees with your voltage. 0 Never use warm or hot water to fill the water container! Use cold water only! 0 Keep your hands and the cord away from hot parts of the appliance during operation. 0 Never clean with scouring powders or hard implements.
SPECIAL CORD SET INSTRUCTIONS
Regarding your Cord Set: A. A short power-supply cord (or detachable power-supply cord) is to be provided to reduce risks resulting from becoming entangled in or tripping over a longer cord. B. Longer detachable power-supply cords or extension cords are available and may be used if care is exercised in their use. C. If a long detachable power-supply cord or extension cord is used, (I) the marked electrical rating of the detachable power-supply cord or extension cord should be at least as great as the electrical rating of the appliance, (2) if the appliance is of the grounded type, the extension cord should be a grounding-type 3-wire cord, and (3) the longer cord should be arranged so that it will not drape over the counter top or table top where it can be pulled on by children or tripped over. D. This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit into a polarized outlet only one way. If the plug does not fit fully into the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to modify the plug in any way.
Krups Espresso Novo 2000 Plus
a: Removable water reservoir b: Warming plate for cups c: Control dial 0 OFF position rP Espresso position & Steam position d: Swiveling steam nozzle e: Perfect Froth attachment f: Water level indicator g: Removable overflow grid h: Removable drip tray

i: Filter holder j: Thermostat light (yellow) k: ON/OFF indicator light (red) I: ON/OFF-Switch m: Measuring spoon n: l-cup or ~-CUP filter basket with Crematic System
%-_: b /_ _ ar iLzrL?l L!!
____ fEE_fi tt== _____ ______ _____ __------______-
Thermoblock Heating System features a 47 tube which heats up water to the precise temperature for brewing espresso which is then pumped onto the espresso. When espresso making is done, excess water is flushed from the system into the drip tray. No stale water remains in the system and there is no bacteria build-up, ensuring a fresher, tasting cup of espresso. One + Two Cup Crematic System Filter Baskets deliver flawless crema-laden espresso every time. One and two cup baskets allow you to choose the desired amount of espresso you wish to brew. Microchip Monitored Steam Pump delivers a constant flow of dry steam. This unique dryness of steam and its regulated pressure froth milk for perfect Program Dial enables you to turn to any of the following three positions I rp I espresso, @ for steaming and 0 = OFF position.
Warming Plate enables you to preheat You espresso and cappucino cups. Perfect Froth Attachment effortlessly produces froth for perfect cappuccino. Water Level Indicator lets you see how much water is in the water reservoir. Removable Drip Tray & Grid is easy to remove and clean.
Your new Espresso Novo 2000 Plus is a machine that has been constructed like no other espresso maker in the world. This machine features a highly sophisticated pump technology called Thermo-Block. Your Espresso Novo 2000 Plus is another one of KRUPS fine espresso makers that.is now available to You for at home use. Genuine Espresso Espresso is a far richer and stronger brew than regular coffee. It should be deep, dark and delicious. Most people find they enjoy it in small quantities because of its richness and for that reason, espresso is usually served in small 2-2.5 oz. demitassse cups. The mark of real espresso is its wonderful inviting fragrance and a light brown Crema, found on top of the surface of the coffee. Your Espressso Novo 2000 Plus, properly used, will always produce espresso that is deep, dark, and delicious. Just follow the instructions and use fresh, well roasted espresso beans.
Ready Light Indicator alerts user when machine has reached the proper temperature. 37 02. Water Reservoir. Large capacity, easy to fill water container, produces a continous number of cups of espresso and cappucino. 15 demitasse cups (2.5 oz.) 7 cappucino cups (5.0 oz.)
Grinding spresso Beans If you choose to grind your own beans we recommend using the KRUPS II Barista #220 grinder. Remember, espresso requires a much finer grind than regular coffee.
We recommend that you get familiar with all the parts of your Espresso Novo 2000 Plus before operating the machine. Insert the filter holder into the machine, and remove and replace water reservoir. Wipe off the steam nozzle and Perfect Froth attachment with a damp cloth to make sure all dust particles from transport are removed. Wash all loose parts in warm, soapy water, rinse thoroughly and dry. When using your Espresso Novo 2000 Plus for the first time we recommend running water through the machine to remove any dust particles which may have settled during shipping. Make sure before you start that the removable overflow grid (g) is properly in place and that the drip tray (h) is properly inserted. Before plugging the appliance into an electrical outlet, make sure that the control dial (c) is in the 0 position and the ON/OFF switch (I) is in the OFF position.

Step 1 Open the water chamber lid and remove the water reservoir (see figure 1). This allows you to conveniently bring the water reservoir to the faucet. l Fill the water container with fresh, cold water just below the hinge of the handle (see figure 2). l Insert the water container back into the appliance (see figure 3). Make sure that it sits in properly so the valve on the base of the water reservoir is activated. The front view water level indicator tells you how much water you have added (see figure 4). l Insert filter holder with either the one or two cup filter basket inserted. Raise the filter holder up into the machine at a 45 degree angle (see figure 5). Turn the filter holder to the right until the marking located on the center of the filter holder handle is within the lock-range indicated on the lower edge of the front panel. This will lock the filter holder into place. Now you are ready to warm up your Espresso Novo 2000 Plus.
Step 2 Place a large cup that has at least a 5 oz. capacity underneath the filter holder spout (see figure 6). l Turn the ON/OFF switch to I ON. The two indicator lights, both yellow and red, will illuminate. As soon as the yellow (thermostat) light goes out, the machine is heated up and ready to use. l Turn the control dial to the I rp 11 position and allow cup of water to run through the machine. Repeat this process until half the water in the water container has been
emptied (see figure 7). THIS WILL REQUIRE YOU TO STAY WITH THE MACHINE TO EMPTY EACH CUP AS IT BECOMES FULL. UPON COMPLETION OF EACH CUP RETURN TO THE 0 POSITION!

Step 2

Make sure the control dial is set to 0 position. Then switch the appliance ON using the ON/OFF switch. Both indicator lights will illuminate (yellow and red). When the yellow indicator light goes out, the machine is ready for use.
Step 3 Step 1 Remove filter holder from the appliance. Choose the desired filter basket which is required for making one or two cups of espresso and insert filter holder (see figure 9). Depending upon which filter basket you have chosen, add one measuring spoon of espresso coffee for each cup of espresso that you are preparing (see figure 10).

Fill the water container with fresh, cold water (see figure I-3). While making espresso, water can be added to the reservoir by opening the hinged water chamber lid and adding water to the water reservoir, using another receptacle to fill the container, Otherwise, the water reservoir can be removed and taken to the faucet.
The one cup filter basket only requires one lecel KRUPS measuring spoon of espresso coffee. The two cup filter basket only requires two KRUPS measuring spoons of espresso coffee.
Lrl CAUTION: IF THE WATER RESERVOIR IS EMPTY AND THE PUMP IS RUNNING, YOU WILL HEAR A VERY DISTINCT NOISE, WHICH IS LOUDER THAN THE NORMAL OPERATING SOUND. IF THIS HAPPENS, TURN THE MACHINE OFF. CHECK WATER RESERVOIR AND REFILL AS NEEDED. NEVER LET THE PUMP RUN WHEN THE WATER RESERVOIR IS EMPTY AS THIS CAN DAMAGE THE PUMP. Prewarming Espresso/ Cappuccino Cups If the machine is being used for the first time during the day, we recommend prewarming your cups with hot water (see figure 8). After you have made several cups of espresso, the cups can be prewarmed on the warming plate (b) of your Espresso Novo 2000 Plus.
Make sure that you do not overfill the filter basket, and that you use the measuring spoon Im) to press your coffee to the proper consistency for brewing (see figure 11). It is also very important that you remove any coffee that might have fallen onto the rim of the filter holder, while you were filling or tamping the coffee (see figure 12). Insert filter holder back into the machine by raising it up at a 45 degree angle and turning it to the right. Turn the filter holder to the right, until it is firmly locked into place. The marking located on the center of the filter holder handle must be within the lockrange indicated on the lower edge of the front panel (see figure 13).
Place a cup which has at least a 2-2,5 oz. capacity underneath the filter holder spout. If you are preparing more than one cup of
espresso, be sure to position two cups underneath the brewing spouts. When preparing cappucino, you will need a cup that has at least a 5 oz. capacity. As soon as the yellow thermosF,aGight goes position out turn the control dial to the ( see figure 14). When the desired amount of espresso is in the cup(s), turn the control dial back to the 0 position. Place the cup aside. To remove the coffee from the filter basket, remove the filter holder from the machine by grasping the filter holder and turning it to the left, until it dislodges. Dispose of used coffee in a waste receptacle (see figure 15). Reinsert the empty filter holder back into the machine to help keep it warm. If you are preparing more than one cup of espresso, disregard the yellow thermostat light. It simply indicates that the thermostat is regulating temperature.

There is no need to prepare espresso before using this steaming feature. For best results, you should use the Perfect Froth attachment fe). If it is not in place, attach it now (see figure 16). KRUPS Perfect Froth attachment lets you froth milk perfectly for making cappuccino.

Step 1

The first step in making cappucino is to make espresso. See section Preparing Espresso. When preparing cappuccino use a cappuccino cup which has a capacity of at least 5 oz. You should fill the cup l/3 way with espresso. Make sure that the control dial is in the 0 position before turning on the machine.
In addition to preparing espresso, you can also use your Espresso Novo 2000 Plus to froth milk for cappuccino. Cappuccino reportedly takes its name from the chocolate hues of the robes worn by the Capuchin monks who favored this delicious desert coffee. While cappuccino is traditionally made up of espresso and frothed milk, it can be tailored to ones own taste with cinnamon, sugar, chocolate flakes, or even liquor. Its versatility makes cappucino a world-wide gourmet choice. As long as your Espresso Novo 2000 Plus is turned on and the water reservoir is properly filled, you can use the steaming feature.
Take a stainless steel frothing pitcher and fill it 113 to l/2 full with fresh, cold milk and set aside. This amount of milk will yield enough froth for two cups of cappuccino. If you need more froth, repeat these steps. We recommend using skim or 2% milk if you prefer a stiff, dense froth. Use regular milk if you prefer a more creamy type of froth.
NOTE: When you start frothing milk, there will be a thumping sound which occurs during the steam preparation. This results from the interval controlled water pump condensing water into steam.
As the thumping sound begins a few drops of water will come out of the steam nozzle before entirely changing over to steam. Step 3
warming plate with a cloth or saucer covering the cups. This will help to keep the espresso hot.
When the yellow thermostat light goes out, insert the steam nozzle half way i to the milk and turn the control dial to I G 1 (see figure 17). Leave the steam nozzle in the milk for approximately 45-60 seconds, depending on how much froth you want and the type of milk you are using.

Attention: The top closure of the Perfect Froth attachment (see figure 24, part A) has a very fine hole which draws air into the milk. If this tiny hole gets clogged, Perfect Froth will not work properly. Therefore, never immerse the top closure in milk or froth. If you wish to prepare espresso immediately after using the steam nozzle, the machine must be cooled down to the proper brewing temperature. (When frothing milk, the temperature of the water is much hotter than when you are brewing espresso.) In order that you do not burn your next batch of espresso, insert the clean filter holder into the machine and turn the control dial to p. Allow l/2 cup of water to run through the machine. This process cools the machine sufficiently to prepare additional cups of espresso.
Do not bring milk to a boil (this will happen if large bubbles start forming at the surface of the milk). Do not let the Perfect Froth attachment touch the bottom of the pitcher. This will prevent you from frothing the milk.

Step 4

After the milk is frothed, keep the Perfect Froth in the milk until the control dial has been turned to the 0 position. This will prevent any splattering from occuring. After milk is frothed, set aside. If you like very stiff froth, let the pitcher set for a few seconds. Now you are ready to add the frothed milk to the already prepared espresso. Pour the milk into the cup by holding back the froth with your spoon. Fill the remainder of the cup with the hot milk and then spoon on the froth. In Italy cappuccino is normally one part espresso to two parts milk plus froth.
It is strongly advised that you wipe off the milk residue which may have collected on the Perfect Froth and steaming nozzle after the frothing process is completed. For a thorough cleaning of the Perfect Froth attachment, remove the separate parts A, B, & C (see figure 24). All parts should be rinsed in warm, soapy water. If the small section of part A is clogged, it can be opened using a fine sewing needle.
If you are making more than one or two cups of cappuccino, it is recommended that you place the finished espresso on top of the

Use caution when removing the Perfect Froth from the steaming nozzle as it may still be hot. Use a damp cloth to clean the steam nozzle. Use caution when cleaning or removing the steaming nozzle as it may still be hot.
After preparing espresso five times, the drip tray and grid may need to be emptied and cleaned (see figures 18 and 19). The water reservoir, drip tray, baffle grid, filter holder, and Perfect Froth attachment should be washed and rinsed in warm, soapy water on a regular basis. Before replacing the drip tray and grid, make sure the baffle has been placed in the drip tray properly (see figure 20). If the steam nozzle becomes clogged for any reason, remove the screw that is holding it in position (see figure 21).
Rinse it under the faucet with warm water. If it is still clogged, take a sewing needle and insert it into the tip of the steam nozzle to free any milk particles.
The warming tray can be removed and wiped with a damp cloth for easy cleaning (see figure 25).
00 NOT PLACE ANY LOOSE PfECES IN THE DISHWASHER. IMPORTANT Clean the steam nozzle each time you have immersed it in milk, otherwise the inside of the nozzle becomes clogged with milk particles. Allow the steam to escape into a wet cloth for one or two seconds after frothing milk. This will flush out any milk residue.
DO NOT TRY TO DISASSEMBLE THE MAIN BODY OF THE MACHINE.
Fill the water container with fresh water. Lime-scale should be removed from the appliance regularly. With hard water and an average daily use of 4 cups of espresso, we recommend descaling every three months. Before descaling, the brewing sieve with seal
must be unscrewed from the brewing head.
Rinse the appliance by allowing one to two water containers full of fresh water to run through the system. Turn off the appliance and let the appliance cool down for 30 min. Replace the sieve with the seal in the brewing head and screw them back on tightly. Replace the Perfect Froth attachment. Attention: Appliance can be still warm.
Remove all lime and remnants of coffee from the sieve and the brewing head. Pull off the Perfect Froth attachment. Dissolve 2 tablespoons of tartaric acid or citric acid (obtainable at drugstores) in 17 ounces of lukewarm water and pour the mixture into the water container. Beware: Never leave machine unattended in the presence of children. Place one receptacle under the brewing head and another under the steam nozzle. Turn on the appliance and set the control dial to the u cp position. Allow about one third of the descaling solution to run through immediately. Leave the control dial on position cp I and turn off the appliance. Now let the remainder of the descaling solution work internally for 1 O-l 5 minutes. Put a receptacle under the brewing head and turn on the appliance again. Allow the second third of the descaling solution to run through. Turn the control dial to the 0 position. Put a receptacle under the steam nozzle. Turn the control dial to the 6 I# position to allow the last third of the descaling solution to run out of the nozzle. Turn the control dial back to the 0 position.

Problem: Coffee leaking from filter holder. Cause:
Filter holder not properly inserted in the machine. Filter holder not pushed in as far as it will go. No elasticjty in the brewing head seal. (This may happen after a long period of use). This part can be ordered through KRUPS Consumer Service Department. If the seal has lost its elasticity, it must be replaced with a new one. Allow the appliance to cool down and then unscrew the sieve from the brewing head. Re-move the seal carefully from the brewing head using a screw driver. Place the new seal onto the machine and then place the flattened side of the sieve back into brewing head.
Problem: Pump makes loud noise. Cause:
No water in the water reservoir. Old or dry coffee is being used, water cannot properly flow through the coffee.
The pitcher that you are using is not suitable. (It is recommended that you use a stainless steel frothing pitcher.) Cold conducts better to metal than to glass or plastic. The type of milk is not suitable. We recommend using 2% or skim milk. Whole milk is acceptable, but due to the fat molecules, it will not have as dense a froth, as if you were to use 2% or skim milk.
Problem: Coffee does not come out of filter holder. Cause:

l l l l

No water in the water reservoir. Water reservoir not inserted correctly. Filter blocked because the coffee mixture is too fine or has been tamped too hard. Machine needs to be decalcified.
Your KRUPS #984 is covered by the following warranty: If from date of purchase within one year this KRUPS product fails to function because of defects in materials or workmanship, KRUPS North America will, at its option, repair or replace the unit without charge, provided the owner has a proof of date of purchase. This warranty will be void if malfunction was caused by damage to the product by accident, misuse, use on frequency or voltage other than marked on the product and/or described in the instructions, abuse including tampering, damage in transit, or use for commercial purposes. This warranty gives you specific legal rights, and you may also have other rights which may vary from state to state.
Problem: Espresso has no Crema. Cause:

Old or dried out coffee being used. Coffee not suitable for espresso. Coffee ground too coarsely. Too little coffee in the filter or not properly tamped.
Problem: Not enough froth when frothing milk. Cause:
Steam nozzle is clogged. Milk is not fresh.

GUARANTEE OF PERFORMANCE

This fine KRUPS product is manufactured according to a rigid code of quality standards, and, with minimum care, should give years of satisfying service. However, should the need arise for repairs or for replacement parts within or after the warrantv period, please call our CONSUMER SERVICE DEPARTMENT: (800) 526-5377 24-hours a day, 7 days a week You will be provided with specific instruction on how to get your product repaired, as well as the name and address of your nearest authorized KRUPS Service Center. The department will also be able to answer any general product questions you may have. Before calling the Consumer Service Department, please have the type number of your KRUPS appliance available. You must have this information before calling our Consumer Service Department so that we may better answer your questions. The type number can be located by looking at the bottom of your appliance. This product is Type #984
Any general correspondance can be addressed to: KRUPS North America, Inc. P.O. Box 3900 Peoria, IL 61612 -

1097/F I 984

KRU PS

nova 4000 Programatic

Model #884
Instructions for Use Warranty Guarantee of Performance

IMPORTANT SAFEGUARDS

When using electrical appliances, basic safety precautions should always be followed to reduce the risk of fire, l Read fl instructions and information in this instruction book and any other literature included in this carton
0 T lo p r o t e c t a g a i n s t e l e c t r i c s h o c k plugs, or appliance in water or other liquid. 0 Close supervision is necessary when any appliance is used by or near children. l Unplug from outlet when not in use and before l
l Do not let cord hang over edge of table or counter, or touch hot surfaces. 0 Do not place on or near a hot gas or electric burner, or in a heated oven. 0 To disconnect, press button to OFF, then remove plug Use extreme caution when dispensing hot steam.

CAUTION

This appliance is for household use. Any servicing other than cleaning and user maintenance should be performed by the nearest authorized KRUPS Service Center (see Guarantee of Performance). Do not immerse base in water. To reduce the risk of fire or electric shock, do not remove the base. No user serviceable parts inside. Repair should be done by an authorized KRUPS Service Center only.

SAVE THESE INSTRUCTIONS

SPECIAL CORD SET INSTRUCTIONS
Regarding your Cord Set: A. A short power-supply cord is provided to reduce risks resulting from becoming entangled in or tripping over a longer cord. B. Longer extension cords are available and may be used if care is exercised in their use. C. If a long extension cord is used, (1) the marked electrical rating of the extension cord should be at least as great as the electrical rating of the appliance, (2) if the appliance is (3) grounding-type S-wire cord, and
Krups Nova 4000 Programatic
a: Removable water reservoir under lid b: Cup warming tray c: ON/OFF button with red indicator light d: Rotary changeover dial e: Central control panel with LED display (from left): - ON/OFF -Automatic onecup portion -Automatic two cup portion - Hot water dispenser Steam Memory
Swivel nozzle for steam and hot water
g: Perfect Froth attachment h: Water level indicator i: Removable cup grid j: Removable drip tray k: ProCrema filter holder I: Measuring spoon
Stainless Steel Pro Thermoblock Heating System (PTS) clears the machine of any excess water in the machines system, and m,aintains the ideal extraction temperature. Microchip Monitored Steam Pump control delivers a constant flow of dry steam. This unique dryness of steam and its regulated pressure froth milk for cappuccino and latte. Electronic Touch Pad Control with LED offers various functions, including automatic one and two cup portioning and memory at the touch of a button. Programmable features lets you set and store the cup portioning to deliver just the right amount of espresso to suit your taste. ProCrema Filter Holder All-in-One ProCrema filter holder features a selector dial that adjusts the amount of coffee you need for 1 cup of regular strength espresso, 2 cups of mild espresso or 1 cup of strong espresso, or 2 cups of regular strength espresso to suit your personal taste. The all-in-one filter holder also features a spring mechanism that will ensure that your coffee is evenly tamped upon insertion for flawless crema-laden espresso every time. Rotary Changeover Dial enables you to steam milk or dispense hot water for tea and other hot beverages. KRUPS unique Perfect Froth attachment takes the guesswork out of frothing milk for cappuccino and latte. n Large 37 oz. removable water reservoir makes continuous cups of espresso, cappuccino and latte. Warming Tray for pre-warming cups.
The KRUPS Novo 4000 Programatic extracts rich, natural flavors from the coffee beans and brings those flavors together to deliver a single perfect cup of espresso. This is achieved by precisely applying the right amount of pressure (15 bars), which draws out all of the coffees natural richness. With the push of a button, you can enjoy the full bodied flavor and aroma of authentic restaurant quality espresso. Genuine Espresso Espresso is a far richer and stronger brew than regular coffee. It should be deep, dark and delicious. Most people find they enjoy it in small quantities because of its richness and for that reason, espresso is usually served in small 2-2,5 oz. demitassse cups. The mark of real espresso is its wonderful inviting fragrance and a light brown Crema, found on top of the surface of the coffee. Your Novo 4000 Programatic, properly used, will always produce espresso that is deep, dark, and delicious. Just follow the instructions and use fresh, well roasted espresso beans. Grinding Espresso Beans If you choose to grind your own beans we recommend using the KRUPS IL Barista grinder #220. Remember, espresso requires a much finer grind than regular coffee.

H Removable Drip Tray and grid allow for easy clean-up.
We recommend that you get familiar with all the part of your KRUPS Novo 4000 Programatic before operating the machine. Insert the filter holder into the machine and remove and replace the water reservoir.
Move the steam nozzle. Wash all loose parts in warm soapy water, rinse thoroughly and dry. When using your KRUPS Novo 4000 Programatic for the first time we recommend running water through the machine to remove any dust particles which may have settled during shipping. A Attention! n Before you start, make sure that the cup grid (i) is in place and the removable drip tray (j) is properly inserted (figure 27).
. n Turn the rotary dial to the 0 position
(see figure 7). Press the ON/OFF button (c) (D. The red indicator light will flash, four LED lights will be stationary green and the memory light M will be orange (see figure 8). When the red indicator light stops flashing, the machine is ready for use (see figure 9). Press the automatic two portion control button m It will flash first, then begin to run water through the system, dispensing the hot water through the filter holder(see figure 10). The portion control is pre-set into memory and will dispense approximately 4 oz. of water, then shut off automatically. You do not need to manually stop or turn off the system. Repeat this process five times, each time waiting for the red light to stop flashing. This process will require you to stay with the machine to empty each cup as it becomes full. n To clear the steam nozzle, press the hot water button = and turn the rotary dial to the 6 position. Place a cup or pitcher under the nozzle (see figure 11). Allow several ounces of water to run through and then turn the rotary dial back to the 0 position. Note: Your machine has a thermostat that controls the temperature continuously so that it will be ready anytime you need it. You may leave your machine on for several hours using a minimum amount of power. If you dont intend to use the machine for a long period of time (overnight, for example), it is recommended that you turn it off.
Step 1 Before first use, we recommend allowing water to run through the machine to cleanse the internal system. n Remove the water reservoir from the machine by lifting up on the handle, located on top of the water reservoir (see figure 1).
W This allows you to conveniently bring the water reservoir to the faucet. Fill with cold water (see figure 2). n Replace reservoir back into the machine (see figure 3). W The water level indicator will let you see how much water remains in the container, and you should refill as needed (see figure 4). n Insert the filter holder (without coffee) into the machine and raise it up into the brewing head at a 45 degree angle. Turn the filter holder to the right until the marking located on the auto-eject button of the filter holder handle is within the lock-range indicated on the lower edge of the front panel. This will lock the filter holder into place (see figure 5).

You are now ready to warm-up the machine. Step 2 n Place a cup that has at least a 5 oz. capacity under the filter holder spout and another cup or frothing pitcher under the steam nozzle (see figure 6). When using the appliance, you should prewarm the cups with hot water. Afterwards, you can keep the cups at their ideal temperature by placing them on top of the warming tray upside down. You may also want to place a dishcloth on top of the cups to help keep them warm.
Pre-Warming Cups: Turn the rotary dial to the 0 Position. Insert the filter holder without coffee into the machine. Press the ON/OFF button (cl a. The red indicator light will flash, four LED lights will be stationary green and the memory light M will be orange. When the red indicator light stops flashing, the machine is ready for use. Place cup(s) under the filter holder spout and press one or two portion control button according to the size of the cup(s). If the machine is ready for use, the warming tray will slowly begin to heat up. Place the cups upside down onto the warming plate.
The filter holder selector ring can be adjusted to three individual positions to suit your personal taste (see figure 121: R 1 cup regular strength espresso 4p,p 1 cup strong espresso 2 cups mild espresso J@ 2 cups regular strength espresso Turn the selector ring to the desired position. l Depending on which setting you have chosen add one, one and a half, or two KRUPS measuring spoons of espresso coffee (see figure 13). m Make sure that you do not overfill the basket. Press (tamp) the coffee lightly into the filter holder using the back of your KRUPS measuring spoon (see figure 14). Your ProCrema filter holder also features a built-in tamper, which will ensure that the coffee has been evenly tamped.
Step 1 n Fill the water reservoir with fresh cold water (see figures l-31. Step 2 n Turn the rotary dial to the 0 position (see figure 7).
n It is also vet-y important that you remove any coffee that has fallen onto the rim of the filter holder while you were filling or tamping the coffee (see figure 151. n Insert the filter holder into the machine by raising it up at a 45 degree angle. Turn the filter holder to the right until it is firmly locked into place. The marking located on the auto-eject button of the filter holder handle must be within the lock-range indicated on the lower edge of the front panel (see figure 181. Place the warmed cup(s) under the filter holder spout. Step 4 The machine is already pre-programmed to prepare either one (1.7 oz.) or two (4 oz.) cups of espresso. n Press the appropriate button for one cp or two 12p (see figure 17). The green light will begin to flash and the appropriate amount of coffee will be dispensend. Once brewed, the red indicator light will begin to flash, indicating that the machine is readjusting the brewing temperature. However, this will not stop you from continuing to brew espresso.

W Press the ON/OFF button (cl 0. The red indicator light will flash, four LED lights will be stationary green and the memory light M will be orange (see figure 8). When the red indicator light stops flashing, the machine is ready for use. To prevent previous coffee particles from clogging the brewing head, run a small amount of water through the filter holder (see Using for the first time) without coffee. Hint: Leave the filter holder in the machine without coffee and allow it to heat for several minutes before brewing. This, along with pre-warming the cups will contribute to a hotter cup of espresso. Step 3 n Remove the ProCrema filter holder from the machine.
Caution: Your Novo 4000 Programatic machine can be used to dispense hot water for tea, cocoa, instant soup and other hot beverages by using the steam/hot water nozzle (do not use the Perfect Froth attachment for this procedure). Step 1 Make sure the reservoir is filled with fresh, cold water. Turn the rotary dial to the 0 position and turn the machine ON. When the red indicator light stops flashing, swing out the steam/hot water nozzle (f) and place a cup under the nozzle. n Press the HB: button and turn the rotary dial to the.$J position (see figure 22).
If the water reservoir is empty and the pump is running, you will hear a distinct noise, which is louder than the normal operating sound. Turn off the machine! Never let the pump run when the water reservoir is empty, as this can damage the pump. Step 5 n To remove coffee from the filter basket, remove the filter holder from the machine. To remove the coffee cake from the filter holder, press the auto-eject button located on the handle and knock out the espresso grounds (see figure 18).
Reinsert the filter holder back into the machine to help keep it warm.
The memory function can be used to alter the pre-programmed portions to make shorter or taller amounts of espresso. Once selected, the new portion will remain in memory until the next time it is manually changed. Step 1 Turn ON the appliance as you would for preparing espresso. Insert the filter holder (with coffee) into the brewing head. Place a cup under the filter holder. Once the red indicator light stops flashing, press the M key. The M indicator light will flash, while the indicator lights for one and two cup portions will remain constant (see figure 19). Press and hold in either the one Q or two Sp selection until the desired quantity of espresso is dispensed (see figure 201. Press the M key to store the new programmed amount into memory (see figure 21 I.

When you have reached the desired quantity of hot water, turn the rotary dial back to the 0 position. Note: If you do not turn the rotary dial to activate the hot water function within 2 minutes, the machine will automatically reset to the normal operating mode. Once you have removed the cup from under the steam/hot water nozzle, swing the nozzle inward, over the drip tray to catch any excess water.
Exercise caution when using the steam nozzle, it is very hot!
In addition to preparing coffee and espresso, you can also use your Novo 4000 Programatic machine to froth milk for cappuccino. Cappuccino is traditionally served in a 5 oz. cup consisting of l/3 espresso, l/3 steamed milk, topped with l/3 froth. n For best results, you should use the included KRUPS patented Perfect Froth attachment (see figure 23).
The Perfect Froth attachment should be used to froth milk only. As long as the machine is ON and the water reservoir is properly filled, you can froth/steam at any time. It is not required that you brew coffee before frothing/steaming. The thumping sound which occurs during frothing/steaming results from the interval-controlled water pump. As the thumping sound begins a few drops of water will come out of the nozzle before changing to steam. Step 1
Step 3 Pour the steamed milk to the waiting espresso and spoon on froth. If you prefer stiff froth, let the pitcher stand for a few seconds after frothing. Immediately wipe off the milk residue left on the nozzle (see Cleaning). Heating liquids n To conveniently heat liquids, make sure that the Perfect Froth attachment is removed. Follow the same instructions for frothing milk, placing the steam nozzle into a cup or receptacle and steaming (see figure 26).
The first step in making cappuccino is to make espresso (see Preparing Espresso). When making cappuccino, use a cappuccino cup which has a capacity of at least 5 oz. Fill one third to half the cup with espresso, depending on your personal taste. Step 2 Fill a stainless steel pitcher l/3 to l/2 full with fresh, cold milk (skim or low-fat works best). n With the rotary dial in the 0 position, press the 6 button (see figure 24).
Perfect Froth: It is strongly advised that you wipe off milk residue from the steam nozzle and Perfect Froth once frothing is complete. n For a thorough cleaning, remove each separate part (see figure 33). All parts should be handwashed in warm, soapy water. n If the nozzle becomes clogged for any reason, remove the screw holding the steam nozzle in position (see figure 32) and remove all milk particles (use a needle and rinse running water). Replace the steam nozzle and be sure screw is turned tightly. A Use caution when removing the Perfect Froth attachment; it may still be hot.

w Submerge the tip of the Perfect Froth approximately l/2 way. Do not let Perfect Froth touch the bottom of the pitcher; it will prevent the milk from properly frothing. Turn the rotary dial to the (?3 position (see figure 25). Leave the steam nozzle in the milk for about 45-60 seconds, depending on the consistency of froth you desire and type of milk being used. Attention: Do not bring milk to a boil (if large bubbles start forming at the surface of the milk). The top closure of the Perfect Froth has a very fine hole which draws air into the milk. If this hole becomes clogged, the Perfect Froth will not work properly. Never immerse the top closure. Once the milk is frothed, keep the Perfect Froth tip submerged as you turn the rotary dial back to the 0 position. This will prevent any hot milk from splattering.
Important Clean the steam nozzle each time it has been immersed in milk, otherwise the inside of the nozzle becomes clogged and difficult to remove. Allow the steam to escape into a wet cloth for one or two seconds to flush any residue.
Cleaning the ProCrema filter holder Do not place the ProCrema filter holder in the dishwasher. Rinse the filter holder under running water after each use.
process three times. Then switch off the appliance immediately and allow the remainder of the solution to act internally for lo-15 minutes. Now switch the appliance on again and repeat the entire process a further time. Place a receptacle beneath the steam I hot water nozzle and press the Q key. As soon as the red control lamp glows continuously, turn the steam knob to the @ position. Allow the appliance to generate steam for about 1 minute. Now return the knob to the 0 position and switch machine off for 10 minutes. Then switch the appliance on again and repeat this process a further time. After the steam generation, allow the remainder of the descaling solution to run through the brewing head be pressing either the Cp or the m key. After the completion of the descaling operation, wash out the water container thoroughly with clean water. Place receptacle beneath the brewing head and fill the water container with clean water. Switch on the appliance. As soon as the red control lamp glows continuously, press the Sp key. Repeat this operation five times. Now place a receptacle beneath the steam / hot water nozzle and press the clr, key. As soon as the red control lamp glows continuously, turn the steam knob to the @ position and let the appliance generate steam for about a minute. Then return the steam knob to the 0 position and switch off the appliance. Insert the valve spring with the rubber seal upwards. Relocate the brewing sieve and seal in the brewing head. Empty the drip tray and clean it.

Should the filter holder require a more thorough cleaning, loosen the screw located in the center of the filter holder (see figure 301. by hand. Replace each part as shown on figure 31.
n Slowly remove each part and gently rinse

General Cleaning:

n After use, empty the water reservoir and
drip tray (see figure 27). After preparing espresso approximately 10 times, the drip tray will need to be emptied and cleaned in warm, soapy water.
n Before replacing the drip tray and grid,
make sure the baffle has been placed in the back of the drip tray (see figure 28 + 29). Do not try to disassemble the main body of the machine!
The appliance should be descaled at regular intervals taking into consideration the hardness of the local water. For this purpose, the brewing sieve and its sealing ring MUST first be unscrewed from the brewing head. In doing this, a valve spring will also fall out. Remove lime and coffee powder from the brewing sieve and the brewing head. The filter holder must NOT be inserted in the brewing head. Pull the Perfect Froth attachment off the steam / hot water nozzle. Dissolve 4 tablespoons of tartaric or citric acid (obtainable at chemists and drugstores) in 34 ounces of lukewarm water and pour the solution into the water container. Place the largest convenient receptacle beneath the brewing head and switch on the appliance. As soon as the red control lamp glows continuously, press the B key. Repeat this
Problem: Coffee temperature too low. Solution:
n Place the cups on the warming plate of
the appliance to preheat.
Problem: Loud pump noise. Solution: n Check to make sure the water reservoir has been filled and inserted correctly.
. -----.-__-Your KRUPS #884 is covered by the following warranty:
Problem: Not enough froth when frothing milk. Solution: n Steam nozzle or Perfect Froth clogged. n Milk is not fresh. n Milk is not cold. w The pitcher that you are using is not suitable. It is recommended that you use a stainless steel frothing pitcher. n The type of milk is not suitable. We recommend using 2% or skim milk. Whole milk is acceptable, but due to the fat molecules, it will not have as dense a froth, as if you were to use 2% or skim milk. Problem: Coffee does not flow out. Solution: H Make sure water reservoir is properly filled. n n Check whether the water reservoir has been properly inserted. The machine may need to be decalcified (see section Decalcifying).
If within one year from date of purchase this KRUPS product fails to function because of defects in materials or workmanship, KRUPS North America will, at its option, repair or replace the unit without charge, provided the owner has a proof of date of purchase. This warranty will be void if malfunction was caused by damage to the product by accident, misuse, use on frequency or voltage other than marked on the product and/or described in the instructions, abuse including tampering, damage in transit, or use for commercial purposes. This warranty gives you specific legal rights, and you may also have other rights which may vary from state to state.

H Brewing head may be clogged with old coffee grounds.

GUARANTEE OF PERFORMANCE

This fine KRUPS product is manufactured according to a rigid code of quality standards, and, with minimum care, should give years of satisfying service. However, should the need arise for repairs or for replacement parts within or after the warrant-v Deriod, please call our CONSUMER SERVICE DEPARTMENT: (800) 526-5377 2dhours a day, 7 days a week You will be provided with specific instruction on how to get your product repaired, as well as the name and address of your nearest. authorized KRUPS Service Center. The department will also be able to answer any general product questions you may have. Before calling the Consumer Service Department, please have the type number of your KRUPS appliance available. You must have this information before calling our Consumer Service Department so that we may better answer your questions. The type number can be located by looking at the bottom of your appliance. This product is Type #884
Any general correspondance can be addressed to: KRUPS North America, Inc. P.O. Box 3900 Peoria, IL 61612

10971 v I 884.

OfxitI

US 71843