CAUTION

Avoid placing the copier on or in locations which are unstable or not level. Such locations may cause the copier to fall down or fall over. This type of situation presents a danger of personal injury or damage to the copier.... Avoid locations with humidity or dust and dirt. If dust or dirt become attached to the power plug, clean the plug to avoid the danger of fire or electrical shock.. Avoid locations near radiators, heaters, or other heat sources, or locations near flammable items, to avoid the danger of fire. To keep the copier cool and facilitate changing of parts and maintenance, allow access space as shown below. Leave adequate space, especially around the vents, to allow air to be properly ventilated out of the copier. Rear: 11 13/16" 30 cm
During copying, some ozone is released, but the amount does not cause any ill effect to one's health. If, however, the copier is used over a long period of time in a poorly ventilated room or when making an extremely large number of copies, the smell may become unpleasant. To maintain the appropriate environment for copy work, it is suggested that the room be properly ventilated.
Power supply/Grounding the copier

WARNING

DO NOT use a power supply with a voltage other than that specified. Avoid multiple connections in the same outlet. These types of situations present a danger of fire or electrical shock.. Plug the power cord securely into the outlet. If metallic objects come in contact with the prongs on the plug, it may cause a fire or electric shock... Always connect the copier to an outlet with a ground connection to avoid the danger of fire or electrical shock in case of an electric short. If an earth connection is not possible, contact your service representative.. Other precautions Connect the power plug to the closest outlet possible to the copier.
Left: 11 13/16" 30 cm
Front: 39 3/8" 100 cm Other precautions
Right: 11 13/16" 30 cm
The power supply cord is used as the main disconnect device. Ensure that the socket/outlet is located/installed near the equipment and is easily accessible.
Adverse environmental conditions may affect the safe operation and performance of the copier. Install in an air-conditioned room (recommended room temperature: around 68F (20C), humidity: around 65%) and avoid the following locations when selecting a site for the copier. Avoid locations near a window or with exposure to direct sunlight. Avoid locations with vibrations. Avoid locations with drastic temperature fluctuations. Avoid locations with direct exposure to hot or cold air. Avoid poorly ventilated locations.

Handling of plastic bags

Keep the plastic bags that are used with the copier away from children. The plastic may cling to their nose and mouth causing suffocation...

Other precautions DO NOT place heavy objects on the copier or cause other damage to the copier. DO NOT open the upper front cover, turn off the power switch, or pull out the power plug during copying. When lifting or moving the copier, contact your service representative. Do not touch electrical parts, such as connectors or printed circuit boards. They could be damaged by static electricity. DO NOT attempt to perform any operations not explained in this handbook. CAUTION: Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. Do not look directly at the light from the scanning lamp as it may cause your eyes to feel tired or painful.
Cautions when handling consumables
DO NOT attempt to incinerate the toner container. Dangerous sparks may cause burns... Keep the toner container out of the reach of children.. If toner happens to spill from the toner container, avoid inhalation and ingestion, as well as contact with your eyes and skin. If you do happen to inhale toner, move to a place with fresh air and gargle thoroughly with a large amount of water. If coughing develops, contact a physician. If you do happen to ingest toner, rinse your mouth out with water and drink 1 or 2 cups of water to dilute the contents of your stomach. If necessary, contact a physician. If you do happen to get toner in your eyes, flush them thoroughly with water. If there is any remaining tenderness, contact a physician. If toner does happen to get on your skin, wash with soap and water. DO NOT attempt to force open or destroy the toner container.. Other precautions After use, ALWAYS dispose of the toner container in accordance with Federal, State and Local rules and regulations. Store all consumables in a cool, dark location. If the copier will not be used for an extended period of time, remove the paper from the drawer, return it to its original package and reseal it.

Laser Safety

Laser radiation could be hazardous to the human body. For this reason, laser radiation emitted inside this machine is hermetically sealed within the protective housing and external cover. In the normal operation of the product by user, no radiation can leak from the machine. This machine is classified as Class 1 laser product under IEC 60825. CAUTION Performance of procedures other than those specified in this manual may result in hazardous radiation exposure. This label is attached to the laser scanner unit inside the machine and is not in a user access area.

The labels shown below are attached on the rear side of the machine.
CAUTION! The power plug is the main isolation device! Other switches on the equipment are only functional switches and are not suitable for isolating the equipment from the power source.
VORSICHT! Der Netzstecker ist die Hauptisoliervorrichtung! Die anderen Schalter auf dem Gert sind nur Funktionsschalter und knnen nicht verwendet werden, um den Stromflu im Gert zu unterbrechen.
DECLARATION OF CONFORMITY TO 89/336/EEC, 73/23/EEC and 93/68/EEC
We declare under our sole responsibility that the product to which this declaration relates is in conformity with the following specifications. Limits and methods of measurement for immunity characteristics of information technology equipment Limits and methods of measurement for radio interference characteristics of information technology equipment Limits for harmonic currents emissions for equipment input current 16A per phase Limitation of voltage fluctuations and flicker in low-voltage supply systems for equipment with rated current 16A Safety of information technology equipment, including electrical equipment Radiation Safety of laser products, equipment classification, requirements and users guide EN55024 EN55022 Class B EN61000-3-2 EN61000-3-3 EN60950 EN60825-1

Section 2

NAMES OF PARTS

Main Body

(3) (4) (5)

(6) (9) (8) (10)

(1) Original cover (Open/close this cover when you are setting the original on the platen.) (2) Platen (Set originals here for copying. Be sure to lay originals face-down and align them flush up against the left rear corner of the platen.) (3) Original size indicator plate (Be sure to align originals flush up against this plate when setting them on the platen.) (4) Operation panel (Perform copy operations here.) (5) Upper front cover (Open this cover when you need to replace the toner container or if a paper jam occurs inside the copier.) (6) Front cover (Open this cover when you need to replace the toner container or if a paper jam occurs inside the copier.) (7) Process Unit (Take this unit out when you need to replace the toner container or if a paper jam occurs inside the copier.)
(8) Toner container (9) Lock lever (Operate this lever when you need to replace the toner container.) (10) Toner container release lever (Operate this lever when you need to replace the toner container.) (11) Charger cleaner (Slide this knob back and forth when you need to clean the charger.)
(15) (14) (13) (13) (19) (12) (17) (18) (19)
(12) Drawer (This drawer has a storage capacity of 250 sheets of standard copy paper (80 g/m).) (13) Paper width guides (Adjust these guides to fit the width of the paper that is to be loaded in the drawer.) (14) Paper stopper (Adjust this stopper to fit the length of the paper that is to be loaded in the drawer.) (15) Stopper extension lock (Use this lock when loading Folio or Oficio II size paper in the drawer.) (16) Copy storage table (Finished copies can be ejected and stored on this table. The copy storage table has a storage capacity of 150 sheets of standard copy paper (80 g/m).) (17) Multi-bypass tray (Set paper on this tray when copying onto small-size or special paper.) (18) Multi-bypass extension (Pull out this extension when using the multi-bypass tray.) (19) Insert guides (Align these guides to fit the width of the paper that is to be set on the multi-bypass tray.)

Initial mode (the state that the copier enters at the end of
warm-up or when the Reset/Power key is pressed) The upper drawer is selected as the source for paper feed, the number of copies to be made is set to 1 and Text & Photo is selected as the image quality mode. * If the optional Paper Feeder is installed on your copier, it is possible for you to change which drawer will be automatically selected in the initial mode. * It is also possible for you to change which image quality mode will be automatically selected in the initial mode.

Auto Clear function

A pre-set number of seconds (between 10 and 270) after copying stops, the Auto Clear function will automatically engage and the copier will return to the same settings as those after warm up (initial mode settings).(However, the copy exposure setting will not change.) Copies can continually be made using the same settings (copy mode and number of copies) if the next batch of copying is started before the Auto Clear function engages.
Auto Drawer Switching function
If two drawers contain the same size of paper and the paper in one drawer runs out during copying, the Auto Drawer Switching function will switch paper feed from the empty drawer to the other drawer that still contains paper so that copying can continue non-stop. * The optional Paper Feeder is required in order to use the Auto Drawer Switching function. * It is possible for you to turn the Auto Drawer Switching function OFF.

Section 3

PREPARATIONS

Loading paper

Copy paper can either be loaded into the drawer(s) or set on the multi-bypass tray.
Loading paper into a drawer
Standard copy paper (60 g/m 90 g/m), thick paper (90 g/m 105 g/m), recycled paper, or color paper can be loaded into each drawer. Up to 250 sheets of standard copy paper (80 g/m) can be loaded into each drawer at one time. The sizes of paper that can be loaded into the drawers are: A4, A5R, Folio, 8 1/2" 14" (Legal), 8 1/2" 11" (Letter) and 8 1/2" 13" (Oficio II).

Note when adding paper

After taking new paper out of its packaging, be sure to fan through them a few times to separate the sheets before loading the paper into a drawer or setting it on the multi-bypass tray.
When loading copy paper for the first time, or when changing paper sizes, be sure to use the operation panel to register the size of paper that will be loaded in the corresponding drawer. (See page 3-4.) When using thick copy paper (90 g/m 105 g/m), be sure to select the Thick Paper mode. (See page 3-9.)
If you ever use paper that has already been copied onto, be sure NOT to use paper that still has staples or clips attached to it. Doing so may result in lowered copying quality or even damage to the copier. If you are using paper that has been folded or is curled at all, straighten it out before loading the paper into a drawer or setting it on the multi-bypass tray. Failure to do so may result in a paper jam.

Pull the drawer all the way out of the copier.
Set the paper in the drawer so that the leading edge is aligned against the paper stopper, but making sure that none of the paper gets caught on the overhanging tabs.
When pulling the drawer out of the copier, be sure to support it so that it doesnt fall out suddenly.
ALWAYS adjust the paper stopper and paper width guides BEFORE loading paper into the drawer. Failure to do so may result in skewed paper feed and/or a paper jam. Make sure that the paper is set securely against the paper stopper and the paper width guides. If there is any gap between the paper and the stopper or guides, readjust the paper stopper and/or the paper width guides, as appropriate. When you are loading paper into the drawer, make sure that the side to be copied onto is facing downward. Be sure to load paper so that it is not folded or curled, etc. DO NOT load more paper than indicated by the lines located on the width guides.
Adjust the paper stopper in the rear portion of the drawer by pressing in on the release buttons and sliding the paper stopper to the fit the size of the paper being loaded.
The paper sizes are marked on the bottom of the drawer. The factory default setting is for A4/Letter size paper. For information on adjusting the paper stopper for Folio or Oficio II size paper, see Adjusting the paper stopper for Folio or Oficio II size paper on page 3-3.
Adjust the paper width guides on both sides of the drawer by pressing in on the release buttons and sliding the guides to fit the width of the paper being loaded in the drawer.
The paper sizes are marked on the bottom of the drawer. The factory default setting is for A4/Letter size paper.
Push the drawer securely all the way back into the copier until it stops.
Adjusting the paper stopper for Folio or Oficio II size paper
Perform the following procedure to adjust the paper stopper when you want to load Folio or Oficio II size paper into the drawer.
Remove the stopper extension lock from the paper stopper.
If you will not be using the copier for a prolonged period of time, remove all paper from the drawer(s) and seal in its original packaging in order to protect it against moisture.
Slide the paper stopper towards the rear of the drawer until the grooves (1) that are cut into the paper stopper are aligned with the rear edge of the drawer.
Insert the stopper extension lock into the holes in the paper stopper.
Press down on the stopper extension lock and slide the paper stopper towards the rear of the drawer to set the lock into place. The paper stopper is now in position for Folio and Oficio II size paper.

Selecting the paper size

Perform the following procedure to use the operation panel and select the size of paper that is loaded in the drawer.
Press down on the Paper Select key for at least 3 seconds. The first default item for paper size selection will be shown.
Press the Number of Copies / Zoom(+) or Number of Copies / Zoom(-) key until F12 (Default item: Upper Drawer Paper Size) is shown.
To select the size of paper loaded into the optional Paper Feeder, make sure that F13 (Default item: Paper Feeder Paper Size) is shown.
Press the Recall%/Enter key.
Press the Number of Copies / Zoom(+) or Number of Copies / Zoom(-) key to select the appropriate paper size. The displayed code numbers refer to the available paper sizes as explained in the following table.
Setting paper on the multi-bypass tray
Standard copy paper (60 g/m 90 g/m), thick paper (90 g/m 163 g/m), color paper, OHP transparencies and letterhead paper can be set on the multi-bypass tray. ALWAYS use the multi-bypass tray when copying onto special paper. The sizes of paper that can be set on the multi-bypass tray are as follows: Inch Specification 8 1/2" 14" (Legal) 5 1/2" 8 1/2" (Statement) Metric Specification A4 A6R, and Folio

Code number

-A4 -A5 -Fo -Lg -Lt -o2
A4 A5 Folio Legal (8 1/2" 14") Letter (8 1/2" 11") Oficio II (8 1/2" 13")
The types of paper and the number of sheets that can be set on the multi-bypass tray at one time are as follows: Standard paper (80 g/m): 50 sheets Thick paper (120 g/m): 25 sheets Thick paper (160 g/m): 10 sheets OHP transparencies: 1 sheet
After setting paper on the multi-bypass tray, be sure to use the operation panel to select the size of that paper. (See page 3-7.) If you want to copy onto non-standard size paper, be sure to use the F15 (Non-Standard Size Paper Width) default item to register the paper size. (See page 6-2.) When using thick copy paper (90 g/m 105 g/m), be sure to select the Thick Paper mode. (See page 3-9.) When using OHP transparencies, be sure to use a type of film that can withstand the heat of the fixing process. The following products are recommended: Arkwright (LTR) 3M PP2500 (A4)

Press the Number of Copies / Zoom(+) or the Number of Copies / Zoom(-) key until the number that corresponds to desired layout order (1 4) is shown. The displayed code numbers refer to the available layout orders as explained in the following table.

Sort mode

Multiple originals can be scanned into memory in a single operation and then the desired number of copy sets created.
Press the Sort key to light the Sort indicator.
Once all of the originals have been scanned, press the Recall%/Enter key or the Sort key. Copying will start.
If the optional Document Processor is installed on your copier, the Sort mode will be selected automatically once originals are set there. If the optional Document Processor is installed on your copier, all of the originals set there will be scanned and the copy operation will start.

Section 6

COPY DEFAULT SETTINGS

Available default items

The state that the copier enters at the end of warm-up or when the Reset/Power key is pressed is called the initial mode. The modes, functions and other settings that are automatically pre-set for use in the initial mode are called default settings. These default settings can be changed as desired to suit your copying needs. Each default item, as well as each of the available settings for each item, are represented by code numbers on the copy quantity/magnification display. Refer to the Available settings column in the following tables for the code number that correspond to each setting value. The factory default setting is indicated by an asterisk.

Item number

F00 F01 F08

Default

Quit Default Settings User Copy Setting List Black Line Correction

Description

Quits the default settings and returns the copier to a copy-ready state. Prints out a list of the currently selected default settings. If black lines appear on copies when you feed originals from the Document Processor (but they do not exist on the originals themselves), this function will make them less apparent. If Black Line Correction is turned on, however, small and/or detailed text may not be reproduced as clearly as before, so it is normally recommended that you do not change this function from its factory default setting. * Black Line Correction is not available when the Photo mode is selected as the image quality mode. Registers the size of paper that is loaded in the drawer that is included with your copier.

Available settings

----1-: OFF* 2-: Weak 3-: Strong

Reference page

--6-4 6-4 6-7

Upper Drawer Paper Size

-A4: A4 -A5: A5 -Fo: Folio -Lg: Legal -Lt: Letter -o2: Oficio II (Inch specification default: Letter) (Metric specification default: A4) -A4: A4 -A5: A5 -Fo: Folio -Lg: Legal -Lt: Letter -o2: Oficio II (Inch specification default: Letter) (Metric specification default: A4)

6-4 6-7

Paper Feeder Paper Size (option)
Registers the size of paper that is loaded in the optional Paper Feeder. * If the optional Paper Feeder is not installed on your copier, this default setting will not appear.
Multi-Bypass Tray Paper Size
Registers the size of paper that is to be set on the multi-bypass tray. * The XXX shown here refers to the actual width of the paper as registered under the Non-Standard Size Paper Width and it is that number which will be shown on the display.
-A4: A4 -A5: A5 -A6: A6 -Fo: Folio -Lg: Legal -St: Statement -Lt: Letter -o2: Oficio II XXX: Non-Standard Size (Inch specification default: Letter) (Metric specification default: A4) Inch specification: 4.13 8.50 (Default: 4.13) Metric specification: mm (Default: 105 mm) ON* OFF
Non-Standard Size Paper Width
Sets the width of the paper to be set on the multi-bypass tray when that paper is of a non-standard size. * Non-standard size paper of up to 14", or 356 mm, in length can be used. Sets whether the Off mode, which automatically turns most of the power to the copier off when a certain time elapses without any operation being performed, will engage automatically or not. * If the Off mode interferes in any way with your copying operations, turn this function OFF. It is recommended, however, that you try to set a longer time interval until the Off mode engages before you actually turn it OFF. Sets the amount of time after each copy job is finished until the Low Power mode automatically engages. Sets the amount of time without any operation being performed until the Off mode automatically engages. It is also possible to disable the Off mode. When the Off mode is turned OFF, this default setting will not appear. (See Off Mode ON/OFF) * If the Off mode is turned off under the Off Mode ON/OFF setting, this default setting will not appear. * It is recommended that you try to set a longer time interval before the Off mode engages if you use the copier frequently, and to a shorter time if it is used less frequently. * In order to disable the Off mode, see Off Mode ON/OFF. Sets whether the alarm which sounds when an error occurs, etc., will be turned ON or OFF. Adjusts the location of the copied image if it is shifted off-center (either forward or backward) when the Document Processor is used to make copies. * If the optional Document Processor is not installed on your copier, this default setting will not appear. Adjusts for off-center printing.

Press the Recall%/Enter key. The operation panel will return to the display in step 2. Once you are finished accessing default items, proceed to the next step.
Refer to steps 1 and 2 and access the actual F30 default item. Press the Recall%/Enter key.
Press the Reset/Power key. The copier will return to a copy-ready state.
Fold the printed sheet (that you made in step 19) up the middle and compare the true center with the printed center line.
Prior to performing the adjustment procedure, it is necessary to use the Document Processor to make copies in a standard copy mode in order to check the amount of shift that is produced. This procedure assumes that you are using the pattern that is printed out using the F27 default item (Upper Drawer Skewed Feed Adjustment) as an original. (F26) Select a standard copy mode and set the original in the Document Processor. Set the original into the Document Processor in the direction shown in the illustration and make a copy.
For each tenth (0.1) that you increase the setting, the image will be moved 0.1 mm to the right.
Press the Recall%/Enter key. The operation panel will return to the display in step 2.
Refer to steps 1 and 2 and access the actual F26 default item. Press the Recall%/Enter key.
Use the Document Processor to make another copy and, if further adjustment is necessary, repeat steps 20 through 25.
Arrange the original and copy one on top of the other to verify the direction and amount of the shift. If the result is as shown in example (1), increase the setting. If the result is as shown in example (2), decrease the setting.
It is possible to change the setting to any number (step) between -32 - 32. Each one-step adjustment is equal to a 0.3 mm shift.
Use the Document Processor to make another copy and, if further adjustment is necessary, repeat steps 28 through 32.
Checking the total copy count and printing out a report
It is possible to use the operation panel to check the total number of copies made. It is also possible to print out that information in the form of a report. Sample Total Count Report
Press down on the Stop/Clear key for at least 3 seconds. The copy count will begin to be shown on the copy quantity/ magnification display.
The copy count will be shown in three portions in the following order. (In this example, the total number of copies made is 1,234.)
If you press the Start key while the total copy count is being shown, the Total Count Report will be printed out. If you are going to print out the Total Count Report, make sure that there is 8 1/2" 11" (Letter) or A4 paper either loaded in a drawer or set on the multi-bypass tray.
Once the total copy count has been shown, the copier will return to a copy-ready state.

Section 7

TROUBLESHOOTING
If one of the following indications is displayed

Open the upper front cover.
Set the Process Unit into the copier by aligning the pins on both sides of the Process Unit with the guides inside the copier, and then slide the Process Unit all the way back into the copier until it stops.

Open the front cover.

Take the Process Unit out of the copier.

Close the front cover.

Close the upper front cover.

Paper jam in a drawer

Open and then close the upper front cover. The error indications will go out.
Pull out the drawer that is currently being used.

Remove the jammed paper.

If a paper jam occurs in the optional Paper Feeder, the procedure to remove jammed paper is the same as with the included drawer.
Push the drawer back in firmly.
Paper jam in the paper eject section

Open the face-up tray.

Close the face-up tray.
Paper jam in the multi-bypass tray Original jam in the optional Document Processor
Remove all of the paper remaining on the multi-bypass tray.
Remove all of the originals remaining on the original table.
Open the left cover to the Document Processor.
Reset the paper on the multi-bypass tray.
Remove the jammed original. If the original is caught in the rollers or difficult to remove at all, proceed to the next step.
Open the Document Processor.
Remove the jammed original.
Close the Document Processor.

Reset the originals.

If other trouble occurs
If trouble occurs with your copier, carry out the applicable checkpoints and procedures indicated on the following pages. If the trouble persists, contact your service representative or authorized service center.

Trouble

Nothing lights on the operation panel when the power switch is turned ON. No copies come out when the Start key is pressed. The copies come out blank.

Checkpoint

Is the power plug connected to an AC outlet? Is there some indication of the trouble on the operation panel? Were the originals set correctly?
Connect the plug to an AC outlet.
Check the appropriate response to that indication and perform the corresponding procedure. When setting originals on the platen, set them face-down. When setting originals in the optional Document Processor, set them face-up.
The copies come out too light.
Is the copier in the Auto Exposure Adjustment mode? Is the copier in either the Photo, Text & Photo, or Text mode?

In order to adjust the overall exposure level, perform the Auto Exposure Adjustment procedure. Adjust the exposure to the correct level using the copy exposure adjustment keys. To adjust the overall exposure, perform the corresponding exposure adjustment procedure.
Is the copier in the Eco-Copy mode? Is the Add Toner indicator lit? Is the copy paper wet? The copies come out too dark. Is the copier in the Auto Exposure Adjustment mode? Is the copier in either the Photo, Text & Photo, or Text mode?
Select an image quality mode other than the Eco-Copy mode. Replace the toner container. Replace the copy paper with new paper. In order to adjust the overall exposure level, perform the Auto Exposure Adjustment procedure. Adjust the exposure to the correct level using the copy exposure adjustment keys. To adjust the overall exposure, perform the corresponding exposure adjustment procedure.

4-1 8-2 3-1

The copies are dirty.
Is the platen or the optional Document Processor dirty?
Clean the platen and/or the optional Document Processor. Remove the Process Unit and perform the cleaning operation on the charger.

8-1 8-4

Black or white vertical bands appear on the copies.
Is the charger cleaner in its home position (marked CLEANER HOME POSITION)? If you are using the optional Document Processor, is the slit glass dirty?
Remove the Process Unit and return the charger cleaner to its home position. Clean the slit glass. It is also possible to use the Black Line Correction function to make black lines on the copies less apparent. When setting originals on the platen, align them flush up against its upper left corner. When setting originals in the optional Document Processor, align the original insert guides securely before setting the originals.

8-4 6-1 8-1

The copy image is skewed.
Were the originals set correctly?

Paper jams occur often.

Is the copy paper loaded properly in the drawer? Is the copy paper curled, folded or wrinkled? Is there any jammed paper or loose scraps of paper remaining inside the copier? Does the registered paper size match the size you are actually using?
Load the paper properly. Replace the copy paper with new paper. Carry out the appropriate procedure to remove the paper. Make sure the registered paper size matches the size you are actually using. Shake the toner container a number of times.

3-1 7-3 3-1

The Add Toner indicator doesnt go out even after replacing the toner container.
Did you shake the new toner container enough?

Section 8

MAINTENANCE AND OPERATION INFORMATION

Cleaning the copier

For safety purposes, ALWAYS remove the power plug from the outlet when performing cleaning operations.
Lift open the original cover and wipe the gray portion, as shown in the illustration, with a soft cloth dampened with alcohol or mild detergent.

If the optional Document Processor is installed on your copier, lift open the Document Processor and wipe the gray portion, as shown in the illustration, with a soft cloth dampened with alcohol or mild detergent.
Never use thinner or other organic solvents to clean the Document Processor. If copies appear soiled while using the optional Document Processor, such as black lines appearing on the copy image, the slit glass (a) is dirty. Clean the slit glass with a dry soft cloth, or one dampened with alcohol. Never use water, thinner or other organic solvents to clean the slit glass.
Never use thinner or other organic solvents to clean the original cover.
Replacing the toner container
When toner runs low, the Add Toner indicator will light. If you continue to make copies while the Add Toner indicator is lit, E33 will appear on the copy quantity/magnification display and the copier will stop. Replace the toner container right away. In addition, you should perform the appropriate cleaning operation whenever you replace the toner container.
DO NOT attempt to incinerate the toner container. Dangerous sparks may cause burns.
DO NOT attempt to force open or destroy the toner container.
Lift the Process Unit, together with the toner container, out of the copier.
Place the Process Unit on a clean, level surface. The drum in the Process Unit is sensitive to light. Never expose the drum even to normal office lighting (500 lux) for more than five minutes. Never stand the Process Unit on end.
Pull the lock lever towards you into its release position (marked UNLOCK), then pull the toner container release lever to the right as indicated by the arrow ( ) in the illustration.
Shake the new toner container horizontally 5 or 6 times to ensure that the toner is evenly distributed inside.
Gently remove the old toner container. Put it in the supplied plastic bag and dispose of it.
Remove the orange protective seal.
Set the new toner container into the Process Unit.
Hold the Process Unit stable and push on the areas marked PUSH HERE on the toner container, until the container clicks into place.
Cleaning the charger and the registration roller
Perform the following cleaning operation whenever you replace the toner container.
Slide the green-colored charger cleaner knob back and forth 2 to 3 times, then return it to its home position (marked CLEANER HOME POSITION).
Push the lock lever back into its locked position (away from you).
After cleaning, make sure you restore the charger cleaner to its home position. If the charger cleaner is not restored to the CLEANER HOME POSITION, a black band will appear on subsequent copies.
Use the cleaning cloth that is supplied with the new toner kit to wipe off any paper dust and dirt that has accumulated on the metal registration roller (A) inside the copier.

Document Processor (option)
Original feed system.. Automatic feeding Acceptable originals.. Sheets of paper Original sizes... Max.: 8 1/2" 14" (Legal) and Folio Min.: 5 1/2" 8 1/2" (Statement) and A5R Original paper weight.. 50 g/m 120 g/m Acceptable number of originals.. Maximum of 50 (50 g/m 80 g/m) Power source... Via electrical connection to the copier Dimensions (W) (D) (H).. 17 15/16" 13 1/16" 3 11/16" 455 mm 331 mm 93 mm Weight... Approx. 5.06 lbs. / Approx. 2.3 kg (Specifications are subject to change without notice.)

Paper Feeder (option)

Paper feed system... Automatic feeding from drawer (250-sheet capacity drawer [80 g/m]) Paper sizes... 8 1/2" 14" (Legal), 8 1/2" 11" (Letter), 8 1/2" 13" (Oficio II), A4 (vertical), A5 (vertical) and Folio Acceptable copy paper... <Paper weights> 60 g/m 90 g/m (In the Thick Paper mode: 90 g/m 105 g/m) <Paper types> Standard copy paper, recycled paper and color paper Power source... Via electrical connection to the copier Dimensions (W) (D) (H).. 14 7/8" 14 3/4" 3 1/8" 378 mm 375 mm 79 mm Weight... Approx. 4 7/16 lbs. / Approx. 2.0 kg (Specifications are subject to change without notice.)
Additional Memory (option)
Memory type... 100-pin DIMM Available memory... 16 MB, 32 MB, 64 MB and 128 MB Number of scanable originals.. 16 MB: 125, 32 MB: 220, 64 MB: 250 and 128 MB: 250 (A4, 6% black) (Specifications are subject to change without notice.)
Environmental Specifications
Recovery time from the Low Power mode.10 seconds Transition time to the Low Power mode (at time of purchase)...15 minutes Transition time to the Off and Sleep modes (at time of purchase)...30 minutes

Duplex (2-sided) copying

Not available

Paper feed

Recycled paper made from 100% recycled pulp may be used with this product.
For best copy results and machine performance, we recommend that you use only KYOCERA MITA original supplies for your KYOCERA MITA copier.

KYOCERA MITA EUROPE B.V.

Hoeksteen 40, 2132 MS Hoofddorp, The Netherlands Phone: +31.(0)20.654.000 Home page: http://www.kyoceramita-europe.com Email: info@kyoceramita-europe.com

KYOCERA MITA DANMARK A/S

Hovedkontor: Slotsmarken 11, DK-2970 Hrsholm, Denmark Phone: +45.(70)22.3880
KYOCERA MITA PORTUGAL LDA. o o
Rua de Campolide 55-5 Dt 1070-029 Lisboa, Portugal Phone: +351.(0)21.032.0900
KYOCERA MITA NEDERLAND B.V.
Hoeksteen MS Hoofddorp The Netherlands Phone: +31.(0)20.587.Beacontree Plaza Gillette Way, Reading Berks RG2 0BS, UK Phone: +44.(0)118.931.1500

KM-1500 Specifications

basic specifications:

Configuration: Desktop Digital Copier with Standard 250 Sheet Paper Drawer Plus 50 Sheet Multi-Purpose Tray, 16MB Memory for Scan Once Print Many and Electronic Sort. Optional 50 Sheet Document Processor and 250 Sheet Paper Handling. 600 x 600 DPI Standard 16MB RAM holds approximately 50 Pages (Letter) at 6%. Upgradeable to 144MB via 100 Pin DIMMS (1 Slot). Maximum memory holds approximately 250 pages (Letter) at 6%. Full Size, 3 Reduction, 3 Enlargement Preset Ratios,Auto Magnification, Plus 50-200% Zoom in 1% Increments 120V, 60Hz, 12.0A (w/o DP) 19.5"W x 16.6"D x 15.2"H (w/ DP) 19.5 W x 16.6 D x 17.9 H 30.9 lbs 15,000 Pages Per Month Resolution: Copier Memory:
Magnification: Electrical Requirements: Dimensions: Weight: Max Monthly Volume:

output speeds:

Warm-Up Time: First Copy Out: Pages Per Minute: Within 15 Seconds 9.5 Seconds 15 Letter, 12 Legal

paper supply:

Standard Paper Sources: Drawer Paper Size: MPT Paper Size: Std / Max Paper Capacity: Paper Weight: Input Materials: 250 Sheet Drawer, 50 Sheet MPT 5.5" x 8.5" - 8.5 x 14 5.5 x 8.5 - 8.5 X / 550 16-28 lb bond via Paper Drawers, 16 lb Bond -90 lb Index via MPT Bond Paper, Recycled Paper,Transparencies

copy functions:

Imaging Modes: Continuous Copy: Additional Features:
paper handling options: document processor: DP-100
Type: Acceptable Originals: Capacity: Paper Weight: Dimensions/Weight:
Auto,Text, Photo,Text / Photo, Manual, ECO Up to 99 Scan Once Print Many, Electronic Sort, 2 in 1, 4 in 1,Thick Paper Mode, Manual Imaging
Automatic Document Feeder 5.5 x 8.5" 8.5 x Sheet ADF/ 15 Originals per Minute lb Bond 17.9 H x 13.0 D x 3.7 H/ 5.1lbs.

paper drawers: PF-17

Paper Capacity: Paper Weight: Paper Size: Dimensions / Weight: 250 Sheets 16 - 28 lb Bond 8.5 x 11 - 8.5 x 14 22.5 W x 21.2 D x 5.32 H / 15.4 lbs

additional options:

Platen Cover
Specifications and design are subject to change without notice. For the latest on connectivity visit www.kyoceramita.com. All trademarks and registered trademarks are the property of their respective manufacturers. Kyocera Mita America, Inc. Headquarters: 225 Sand Road, PO Box 40008, Fairfield, NJ 070040008, USA '2003 Kyocera Mita America, Inc. Item Code# 87164139
Kyocera Mita is ISO 14001 Certified for Environmental Management

www.kyoceramita.com