WS-7034U-IT Wireless 915 MHz Temperature Station Instruction Manual

TABLE OF CONTENTS

Topic Quick Setup Inventory of Contents Detailed Setup Guide Battery Installation Setting the Time Selecting Units of Measurement Features Minimum and Maximum Temperatures Resetting Minimum and Maximum Temperatures Adding additional remote temperature sensors (optional) Mounting Troubleshooting Maintenance and Care Specifications Warranty Information Page 3-7 7-8 9

9-11-12

12-13 14-17-18 19-24

QUICK SETUP

Hint: Use good quality Alkaline Batteries and avoid rechargeable batteries. 1. Have the indoor temperature station and remote temperature sensor 3 to 5 feet apart. 2. Batteries should be out of both units for 10 minutes. 3. Place the batteries into the remote temperature sensor first then into the indoor temperature station. (All remote temperature sensors must be started before the indoor temperature station) 4. DO NOT PRESS ANY BUTTONS FOR 10 MINUTES. In this time the indoor temperature station and remote temperature sensor will start to talk to each other and the 3
display will show both the indoor temperature and an outdoor temperature. If the indoor temperature station does not display both temperatures after the 10 minutes please retry the set up as stated above. After both indoor and outdoor temperatures are displayed for 10 minutes you can place your remote temperature sensor outdoors and set your time. The remote temperature sensor should be placed in a dry, shaded area. The remote temperature sensor has a range of 330 feet. Any walls that the signal will have to pass through will reduce distance. An outdoor wall or window will have 20 to 30 feet of resistance and an interior wall will have 10 to 20 feet of resistance. Your distance plus resistance should not exceed 330 ft. in a straight line. 4
NOTE: Fog and mist will not harm your remote temperature sensor but direct rain must be avoided. To complete the set up of your indoor temperature station after the 10 minutes have passed please follow the steps on pages 8-9.
INVENTORY OF CONTENTS 1. The indoor temperature station (Figure 1) 2. The remote temperature sensor (TX29U) and mounting bracket. 3. 3 each, 1/2 Philips screws. 4. One strip of double sided adhesive tape. 5. Instruction Manual and Warranty Card.

Figure 1

ADDITIONAL EQUIPMENT (not included) 1. 1 Philips screwdriver. 2. 2 Fresh AAA Alkaline batteries. 3. 2 Fresh AA Alkaline batteries DETAILED SETUP GUIDE Battery Installation 1. Install 2 AA batteries in the remote temperature sensor. Make sure they do not spring free, or start-up
problems may occur. Install 2 AAA batteries in the indoor temperature station. Do not press any buttons for at least ten minutes.

Battery Cover

Setting the Time 1. Press and hold the SET button for 5 second, 12h will appear in the TIME LCD. 2. Press and release the MIN/MAX button to select either 12h time (am/pm) or 24h time 3. Press and release the SET button 2 times, the hour will flash in the upper left corner. 4. Press and release the MIN/MAX button to set the hours
5. Press and release the SET button to
move to the minute setting
6. Press and release the MIN/MAX
button to set the minutes.
7. Press and release the SET button to
activate the clock. Note: When in 12h mode, there is only a PM display, which appears under TIME. If there is no display here it is AM. Make sure you set the time accordingly. Selecting Units of Measurement
1. Press and hold the SET button for 5
second until 12h or 24h appears in the TIME LCD. 2. Press and release the SET button again, F will appear in the TIME LCD. 3. Press and release the MIN/MAX button to shift between F and C. 4. Press and release the SET button twice to activate settings.
FEATURES Minimum and Maximum Temperatures
1. Press and release the MIN/MAX 2. 3. 4.
button, MIN appears next to the indoor and remote temperatures. The recorded minimum temperature is displayed. The time of the minimum outdoor temperature will also flash. Press the MIN/MAX button, MAX appears next to the indoor and remote temperatures. The recorded maximum temperature is displayed. The time of the maximum outdoor temperature will also flash. Press and release the MIN/MAX button to exit min/max mode. To view optional additional sensors, press and release the SET button while viewing the minimum or maximum.
Resetting Min and Max Temperatures To reset both the minimum and maximum temperaturespress and hold the RESET/+ button for 4 seconds.

Adding Additional Remote Temperature Sensors (optional)
The WS-7034U-IT is able to receive signals from 3 different remote temperature sensors. Following are some brief instructions for the basic set-up of remote temperature sensor units with the WS-7034U-IT. These extra remote temperature sensors can be purchased through the same dealer as this unit, or by contacting La Crosse Technology directly. When setting up multiple remote temperature sensors, it is important to remove the batteries from all existing units in operation, then to insert batteries
first into all the remote temperature sensors. Second install batteries into the indoor temperature station and do not press any buttons for ten minutes. Transmission problems will arise if this is not done correctly. To view the temperature of a different remote temperature sensor unit, press and release the SET/CH button. A shift from one number to the next should be observed in the OUTDOOR LCD. MOUNTING Note: To achieve a true temperature reading, avoid mounting in direct sunlight. We recommend that you mount the remote temperature sensor on a North-facing wall. The sending range is 330ft; obstacles such as walls, concrete, and large metal objects will reduce the range. Place both units in their desired location before permanently mounting.
Remote Temperature Sensor 1. 2. Remove the mounting bracket from the remote temperature sensor. Mount the bracket in the desired location with either screws or adhesive tape. Reattach the remote temperature sensor into mounting bracket.
Indoor Temperature Station The indoor temperature station comes with the table stand already mounted. If you wish to use the table-stand all that is required is to place the indoor temperature station in an appropriate location. 1. 2. 3. To wall mount the indoor temperature station first remove the table stand. Next insert an appropriate screw in your desired location. Using the integrated hanging hole on the back of the unit, slip indoor
temperature station over the screw and pull down to secure. TROUBLESHOOTING NOTE: For problems not solved, please contact La Crosse Technology via e-mail or phone, or visit our website, www.lacrossetechnology.com Problem: The LCD is faint Solution: Replace batteries Problem: No outdoor temperature is displayed. Solution: 1. Remove all batteries, reinsert into remote temperature sensor first, then into the indoor temperature station. 2. Place remote temperature sensor closer to the indoor temperature station. 3. Be sure all batteries are fresh. 4. Place remote temperature sensor and indoor temperature station in position
so the straight-line signal is not passing through more than two or three walls. Problem: Temperatures do not match if units are placed next to each other. Solution: Each temperature sensor is manufactured to be accurate to within 1 degree plus or minus and under normal conditions, so two sensors could be as much as 2 degrees different. However, the difference can be exaggerated further because the sensors are designed for different working environments. The indoor sensor is less responsive to ambient air currents because of the shielding effect of the display's case. In addition, the case can act as a heat sink to absorb and store heat from external sources (i.e. handling of the case or radiant heat). Also, the much greater range of the outdoor temperature sensor requires a different calibration curve than the indoor range. Error is usually greater at the extreme ends of a range, making it harder to compare different ranges with different curves. Under non-laboratory conditions, it

is difficult to compensate for the above factors and obtain an accurate comparison. MAINTENANCE AND CARE INSTRUCTIONS Extreme temperatures, vibration, and shock should be avoided to prevent damage to the units. Clean displays and units with a soft, damp cloth. Do not use solvents or scouring agents; they may mark the displays and casings. Do not submerge in water. Do not subject the units to unnecessary heat or cold by placing them in the oven or freezer. Opening the casings invalidates the warranty. Do not try to repair the unit. Contact La Crosse Technology repairs.
SPECIFICATIONS Transmitting 915MHz Frequency
Measuring Temperatures Indoor 14.1F to 139.82F Temperature 0.2 F resolution. Station (-9.9C to 59.9C 0.1C resolution). Remote -39.8 F to 139.8F Temperature 0.2F resolution. Sensor (-39.8C to 59.9C 0.1C resolution). Temp accuracy +/- 1F (+/-.5C). Transmitting Maximum 330 range (100m) open space. Temperature check Indoor Every 10 seconds. Outdoor Every 4 seconds Batteries(Alkaline recommended) 2 x AA, 1.5V Remote Temperature Sensor 2 x AAA, 1.5V Indoor Temperature Station

with with with with

Dimensions: (L x W x H) 2.36 x.88 x 5.90 in. Indoor (excluding table stand) Temperature (60 x 22.5 x 150 mm). Station 2.32 x 0.86 x 2.55 in. Remote (59 x 22 x 65 mm). Temperature Sensor Battery life Up to 24 months.
WARRANTY INFORMATION La Crosse Technology, Ltd provides a 1-year limited warranty on this product against manufacturing defects in materials and workmanship. This limited warranty begins on the original date of purchase, is valid only on products purchased and used in North America and only to the original purchaser of this product. To receive warranty service, the purchaser must contact La Crosse Technology, Ltd for problem determination and service procedures. Warranty service can only be performed by a La Crosse Technology, Ltd authorized service center. The original dated bill
of sale must be presented upon request as proof of purchase to La Crosse Technology, Ltd or La Crosse Technology, Ltds authorized service center. La Crosse Technology, Ltd will repair or replace this product, at our option and at no charge as stipulated herein, with new or reconditioned parts or products if found to be defective during the limited warranty period specified above. All replaced parts and products become the property of La Crosse Technology, Ltd and must be returned to La Crosse Technology, Ltd. Replacement parts and products assume the remaining original warranty, or ninety (90) days, whichever is longer. La Crosse Technology, Ltd will pay all expenses for labor and materials for all repairs covered by this warranty. If necessary repairs are not covered by this warranty, or if a product is examined which is not in need or repair, you will be charged for the repairs or examination. The owner must pay any shipping charges incurred in getting your La Crosse Technology, Ltd product to a La Crosse Technology, Ltd authorized service center. La Crosse Technology, Ltd will pay ground return shipping charges to the owner of the product to a USA address only.

Your La Crosse Technology, Ltd warranty covers all defects in material and workmanship with the following specified exceptions: (1) damage caused by accident, unreasonable use or neglect (including the lack of reasonable and necessary maintenance); (2) damage occurring during shipment (claims must be presented to the carrier); (3) damage to, or deterioration of, any accessory or decorative surface; (4) damage resulting from failure to follow instructions contained in your owners manual; (5) damage resulting from the performance of repairs or alterations by someone other than an authorized La Crosse Technology, Ltd authorized service center; (6) units used for other than home use (7) applications and uses that this product was not intended or (8) the products inability to receive a signal due to any source of interference. This warranty covers only actual defects within the product itself, and does not cover the cost of installation or removal from a fixed installation, normal set-up or adjustments, claims based on misrepresentation by the seller or performance variations resulting from installationrelated circumstances. LA CROSSE TECHNOLOGY, LTD WILL NOT ASSUME LIABILITY FOR INCIDENTAL, CONSEQUENTIAL, PUNITIVE, OR OTHER
SIMILAR DAMAGES ASSOCIATED WITH THE OPERATION OR MALFUNCTION OF THIS PRODUCT. THIS PRODUCT IS NOT TO BE USED FOR MEDICAL PURPOSES OR FOR PUBLIC INFORMATION. THIS PRODUCT IS NOT A TOY. KEEP OUT OF CHILDRENS REACH. This warranty gives you specific legal rights. You may also have other rights specific to your State. Some States do no allow the exclusion of consequential or incidental damages therefore the above exclusion of limitation may not apply to you. For warranty work, technical support, or information contact: La Crosse Technology 2809 Losey Blvd. S. La Crosse, WI 54601 Phone: 608.782.1610 Fax: 608.796.1020 e-mail: support@lacrossetechnology.com (warranty work)
sales@lacrossetechnology.com (information on other products) web: www.lacrossetechnology.com
FCC DISCLAIMER This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. FCC ID: OMO-01RX (Receiver), OMO-01TX (sensor) Freq. 915 MHz La Crosse Technology Made in China WS-7034it All rights reserved. This handbook must not be reproduced in any form, even in excerpts, or
duplicated or processed using electronic, mechanical or chemical procedures without written permission of the publisher. This handbook may contain mistakes and printing errors. The information in this handbook is regularly checked and corrections made in the next issue. We accept no liability for technical mistakes or printing errors, or their consequences. All trademarks and patents are acknowledged. 1. THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND 2. THIS DEVICE MUST ACCEPT INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.

Inserting batteries Remove the cover of the battery compartment and insert four 1.5 V AA-cells, (alkaline type LR6) according to the correct poles into the battery compartment. Close the battery compartment again. PC-connection To connect the station to a PC, use the USB cable to connect the mini USB jack to the USB port of WS 550 US. The plug at the other end of the cable is connected to the USB port of a PC (also see chapter 9.) Installing / Mounting Depending on the requirement, the weather station can be mounted on a vertical surface (such as a wall) using a hanging eye or installed on an horizontal surface using a table-stand. The table-stands are mounted using the Allen screws and Allen key according to the following description: Start-up (base station)
1. emove the cover of the foot support: R first lock it in at the top, then fold it fully downward and then remove it.
2.Lock in the foot support in the locking nose of the glass foot and place it on the two screw domes.
3.Screw the enclosed Allen key and 2 Allen screws on the glass foot. Please note that the lighting cable of the device foot is guided in from the side as shown in the picture so that it does not get crushed.
4.Place the weather station at the locking nose of the foot support and tilt it on the foot support till the screw dome neatly grips into the corresponding intakes of the weather station. Note! Do not let go of the weather station till both the Allen screws have been fixed in (see next step)! Please do not press the display when you hold the weather station. Hold the weather station only at the frame!
5. Screw the foot support on to the weather station using the enclosed Allen key and 2 Allen screws.
6. The cables are thus connected, inserted into the foot support and guided. Please note that the cable lies exactly in the center as shown so that it will not prevent the lid from subsequently locking in. Note! The cable for lighting the support foot and the USB cable can only be inserted in one direction! Do not insert it using force! Stow away excessive cable in a chamber of the support.
7. Now place the cover for the foot support: Insert it flat into the support intake (also see 1.), fold it upward and lock it in. Note! The cover should fold up easily without any resistance; otherwise, it means the cover has not been placed properly or the cable is not laid correctly in the guide! You can see the correct guiding of the cable.
8. At the end, the cover is inserted in the corresponding locks of the cable shaft (see detailed picture above), tilted upward and locked in at the top (see lower picture).

ENTER

- Touch the "ENTER" field, the display is: LATITUDE + 38.9 -
- Touch the "+" or "-" areas to set the latitude. - Touch the "LATITUDE" field, the display is: LONGITUDE + -77.0 -
- Touch the "+" or "-" areas to set the longitude. - Wait a few seconds; you will then see the corrected day for sunrise and sunset in the display. Please note that the sunrise and sunset details will really be correct at the sea or for a location on the plains. Mountains, high forests can really cut short the actual day. The details can deviate slightly even for the ideal location because an approximation formula is used for the calculations.
3.3.5. "TIMEZONE" menu, Set time zone
The time zone details are required for calculating the sunrise and sunset times. Enter the current difference to UTC (Coordinated Universal Time). The Appendix C countains a table with the time zone difference from UTC for the US. - Select the "TIMEZONE" menu: NEXT TIMEZONE ENTER
- Touch the "ENTER" field, the display is: TIMEZONE + - 05 -
- Touch the "+" or "-" areas to set the longitude. - Wait a few seconds; you will then see the corrected day for sunrise and sunset in the display.
3.3.6. "LIGHTING" menu, time setting for the background lighting and regulating the brightness of the lightening
In this menu you can set the switching time for the background lighting that automatically switches on when you touch the screen and switches off after a set period. This can range from "OFF" (lighting never switches on), to periods between 5 seconds and 10 minutes till permanent lighting (ON). Further, you can also set the times when the lighting should permanently be on. You can also activate/deactivate an automatic adjustment to the surrounding brightness so that the display is optimally legible under all surrounding conditions. The background lighting can only be used if you are connected to the AC adapter! - Select the "LIGHTING" menu: NEXT LIGHTING ENTER
- Touch the "ENTER" field, the display is: LIGHTING + 10 SEC -
- Touch the "+" or "-" areas to set the switch-on time. - Touch the "LIGHTING" field, the display is:

BRIGHT CTRL

- Touch the "ON" field to switch between "Automatic Brightness Control" being active (ON) or deactive (OFF). - Touch the "BRIGHT CTRL" field, the display is: BEGIN +04.00 PM-

4. Changing the batteries

Base station

When the battery empty symbol appears in the INDOOR display area ( ), then all batteries are to be replaced according to the instructions in section 2.1 with those of the same type. Always change all the 4 batteries and use only high-quality alkaline batteries. Leave the AC adapter connected when you are changing the batteries so as to avoid data loss. This Display Unit is designed to run on a/c power. Due to the power requirements of the Display Unit, it ist not recommended to use batteries only for more than a few hours. It ist possible to lose connection with the Combi Sensor if using batteries only. Please note! The data memory is deleted if you do not connect the AC adapter while replacing the batteries.

Wireless sensors

The batteries in these sensors have a lifetime of max. 2 years (alkaline batteries). They are to be replaced when a 'battery empty' symbol ( ) is displayed when you select the corresponding sensor in the "OUTDOOR" display area. Batteries are replaced in TX 550 US according to the instructions in section 2.2.; the instructions for the other sensors are to be found in the respective operating instruction manuals. Please follow the battery disposal regulations! Do not dispose of disposable and rechargeable batteries as part of household garbage!

5. Troubleshooting

Possible disruptions that can hamper proper display of the transmitted measured values are: No reception - the distance between the transmitter and receiver is too much or too less (<3 ft., 1 m). Reduce or increase the distance between the transmitter / receiver. No reception - there are highly resistant materials (thick walls, steel concrete,.) located between the transmitter and the receiver Relocate the transmitter or receiver. Also see chapter 6 ("Range"). No reception - transmitter batteries are empty. Replace batteries. No reception - transmitter is covered by the disturbance source (Wireless device, wireless headphone/ loudspeaker) Remove the source of the fault and look for another position for the transmitter and receiver. Such disturbances are only for a short period (wireless traffic) or can be rectified in a very simple manner. Any wireless headphones, wireless baby phones or similar devices are operated at a frequency of 916.5 MHz in your house or in the vicinity only for a short duration. Most of these devices are enabled for exchanging signals at an interruption-free frequency. Such a measure can effectively fade out all interruptions.

7. Instructions for Maintenance and Care
- Protect the base station against dust and moisture. Never clean it with chemical detergents; just use a soft dry piece of linen. Do not put any pressure on the display. -The outdoor sensor is to be cleaned from time to time to remove the dirt and dust that has settled on it. Check easy accessibility of the wind sensors and ensure that the sensors are fitting tight on the holder.
7.1. Cleaning the rain quantity sensor -Depending on the location, leaves, dirt, sand and branches blown by the wind get collected in the collection funnel of the rain quantity sensor. Larger parts can block the passage. Sand can also accumulate on the pointer; large deposits of it can hamper the measurement result. -Hence the rain quantity sensor is to be cleaned from time to time - at least once a year. The pictures shown below are a guideline for installing / dismantling. - For cleaning the sensor, just remove the sensor housing by slightly turning it to the left. - Further, the collection funnel can also be removed by turning it to the left. -The rainfall sensor is now moved upward, folded towards the cable side and you can now remove the pointer. -Clean the collection funnel, contacts, counter and the drain-hole in the housing and remove all residues. -Place the counter back in its holder. The magnet of the counter should be on the side that faces the cable.
Pointer inserted correctly
Lock for collection funnel
Rainfall sensor inserted correctly
Housing locked in correctly at the bottom (collection funnel removed for demonstration)
Remove Turn to the left, remove casing downward, remove collection funnel upward Mount Mount, turn to the right

Drain hole

-Insert the rain sensor in its holder. It will also automatically hold the pointer. The rain sensor cable and the magnet of the pointer must be located on the same side. -Now place the collection funnel from the top on to the sensor-holder and lock it in by turning it to the right. -Now reinstall the casing and lock it by turning it to the right in the sensor-holder till it locks in. Ensure that the drain-holes of the casing and the sensor-holder match (drain-hole of the casing points outwards). 7.2. Setting the rain sensor The rain quantity measurement system has a high level of accuracy when it leaves the factory; so normally, no adjustments are required. Adjustments would be necessary only if the accuracy requirements are very high. Before you start calibrating the rain water measurement recorder, you need to reset to zero the rainfall quantity value that has already been totaled up (see chapter 3.2. "RESET"), total rain quantity display stands at zero). Further, the rainfall quantity for adjustments must be displayed in "inch". Proceed as follows for exact calibration: 1. Slowly pour 3.38 fl. oz. (100 ml) water over a period of 10 minutes in the rain sensor collection funnel. Note! Quick pouring will give wrong measurement results! Pour the water so slowly into the funnel that there is a even passage of water and there is no water in the funnel at any point of time.

Comfort indicator The symbol of the comfort indicator (the three different "smiles" J K L) reflect the room climate whereby the weather station works according to the following table: Temperature

<64.4 F

air humidity
35% 40% 45% 50% 55% 60% 65% 70%

20% 30%

L L 67.9 - 71.4 F L 71.5 - 75.0 F L 75.1 - 78.6 F L 78.7 - 82.2 F L over 82.2 F L

64.4 - 67.8 F

L L L L K K L

L L L K J K L

L K K J J K L

L K J J J K L

L K J J K K L

L K J K L L L

L K K L L L L

L L L L L L L

One can thus see that depending on the relationship of the temperature to humidity, there are certain marked ranges that can be defined as comfortable or uncomfortable climate. One would thus feel that at a temperature of 77 F (25 C) and a humidity of less than 30% is very dry (for e.g. air from the heaters) and one above 60% as sultry. Daylight saving time switching The integrated clock implements an automatic daylight saving time switching according to the regulations of the Energy Policy Act of 2005.
11. Proper use, Exclusion of warranty, Safety instructions
- This weather station is meant for personal use as an indicator of the forthcoming weather. The forecasts or predictions made by this device are more for orientation and are not to be construed as absolute forecasts. - The manufacturer of the weather station does not assume any liability for incorrectly measured values and consequences that can result from it. - This weather station is not meant for medical purposes or for informing the public. - The components of this weather station are not a toy; they contain many fragile, glass and small parts. Please install all the components out of the reach of children.
12. Wireless technology BidCoS
BidCoS (Bidirectional Communication Standard) is a new wireless standard that has been specially developed for wireless control of sensors and actors for house automation. It allows you to build an entire house controlling system with compatible components: switch/dim lights and other electrical appliances, air-conditioners (heating, cooling, airing, weather measuring technology, energy management, access control, protection against burglary, safety devices, etc.). Speedy bi-directional communication (wireless signals that are sent are confirmed by the receiver) increases the functional safety and thus form the basis for a multitude of options for remote control / remote monitoring. Bi-directional data transfer of WS 550 US to TX 550 and all additional sensors works according to BidCoS Standard.

13. FCC Information

Contains FCC ID: RNT-TRX916 Changes or modifications not expressly approved in writing by La Crosse Technology may void the users authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. The internal antenna used for this mobile transmitter must provide a separation distance of at least 7.874 in (20 cm) from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. DoC Statement This device, trade name La Crosse, model number WS 550 US complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation The responsible party for this device compliance is: La Crosse Technology 2809 Losey Blvd South La Crosse, WI 54601, USA (001) 608-782-1982
Appendix A: Menu Overview WS 550 US Main menu MIN MAX RESET
RESET RAIN RESET SUN RESET MIN-MAX
CFG CLEANING SENSOR LIGHTING TIME/DATE LIVE MODE UNITS POSITION SYSTEM
LIGHTING BRIGHT CTRL BEGIN END TIME YEAR MONTH DAY WEEKDAY HOUR MINUTE BEGIN END TEMPERATURE PRESSURE RAIN LATITUDE LONGITUDE TIMEZONE BEEP DST INTERVALL ALTITUDE RAIN CAL SUN CAL
Appendix B: Table of latitude/longitude of US counties.
State AL AL AL AL AL AL AL AL AL AL AL AL AL AL AL AL AL AL AL AL AL AL AL AL AL AL AL AL AL AL AL AL AL AL AL AL AL AL AL AL AL AL AL AL AL AL AL AL AL AL AL AL AL AL AL AL AL AL AL AL AL AL AL AL AL AL AL AK AK AK AK AK AK AK AK AK AK AK AK AK AK AK AK AK AK County Latitude Autauga County 32.5 Baldwin County 30.6 Barbour County 31.9 Bibb County 33.0 Blount County 34.0 Bullock County 32.1 Butler County 31.7 Calhoun County 33.7 Chambers County 32.9 Cherokee County 34.2 Chilton County 32.9 Choctaw County 32.0 Clarke County 31.7 Clay County 33.3 Cleburne County 33.6 Coffee County 31.4 Colbert County 34.7 Conecuh County 31.4 Coosa County 33.0 Covington County 31.3 Crenshaw County 31.7 Cullman County 34.2 Dale County 31.4 Dallas County 32.4 DeKalb County 34.5 Elmore County 32.6 Escambia County 31.1 Etowah County 34.0 Fayette County 33.7 Franklin County 34.5 Geneva County 31.1 Greene County 32.8 Hale County 32.8 Henry County 31.5 Houston County 31.2 Jackson County 34.8 Jefferson County 33.5 Lamar County 33.8 Lauderdale County 34.9 Lawrence County 34.6 Lee County 32.6 Limestone County 34.8 Lowndes County 32.2 Macon County 32.4 Madison County 34.7 Marengo County 32.3 Marion County 34.1 Marshall County 34.3 Mobile County 30.7 Monroe County 31.6 Montgomery County 32.3 Morgan County 34.5 Perry County 32.6 Pickens County 33.3 Pike County 31.8 Randolph County 33.3 Russell County 32.4 St. Clair County 33.7 Shelby County 33.3 Sumter County 32.6 Talladega County 33.4 Tallapoosa County 32.9 Tuscaloosa County 33.2 Walker County 33.8 Washington County 31.4 Wilcox County 32.0 Winston County 34.2 Aleutians East Borough 55.1 Aleutians West 52.3 Anchorage Municipality 61.2 Bethel 60.9 Bristol Bay Borough 58.7 Denali Borough 63.9 Dillingham 59.2 Fairbanks North Star Borough 64.8 Haines Borough 59.2 Juneau City and Borough 58.4 Kenai Peninsula Borough 60.3 Ketchikan Gateway Borough 55.4 Kodiak Island Borough 57.7 Lake and Peninsula Borough 58.6 Matanuska-Susitna Borough 61.8 Nome Census Area 64.8 North Slope Borough 70.6 Northwest Arctic Borough 66.8 Longitude -86.6 -87.7 -85.3 -87.1 -86.6 -85.7 -86.7 -85.8 -85.3 -85.6 -86.7 -88.3 -87.8 -85.8 -85.5 -86.0 -87.7 -87.0 -86.2 -86.4 -86.3 -86.8 -85.6 -87.1 -85.8 -86.2 -87.2 -86.0 -87.8 -87.8 -85.8 -88.0 -87.6 -85.3 -85.4 -85.9 -86.8 -88.1 -87.6 -87.3 -85.3 -87.0 -86.7 -85.7 -86.6 -87.8 -87.9 -86.3 -88.1 -87.4 -86.3 -86.9 -87.3 -88.1 -85.9 -85.4 -85.1 -86.3 -86.7 -88.2 -86.2 -85.8 -87.5 -87.3 -88.2 -87.3 -87.4 -162.0 -172.5 -149.8 -161.2 -156.8 -149.1 -158.6 -147.6 -135.5 -134.5 -151.0 -131.6 -152.7 -156.4 -149.5 -164.3 -153.9 -160.6 AK AK AK AK AK AK AK AK AK AZ AZ AZ AZ AZ AZ AZ AZ AZ AZ AZ AZ AZ AZ AZ AR AR AR AR AR AR AR AR AR AR AR AR AR AR AR AR AR AR AR AR AR AR AR AR AR AR AR AR AR AR AR AR AR AR AR AR AR AR AR AR AR AR AR AR AR AR AR AR AR AR AR AR AR AR AR AR AR AR AR AR AR AR Prince of Wales Sitka City and Borough Skagway-Hoonah-Angoon Southeast Fairbanks Valdez-Cordova Wade Hampton Wrangell-Petersburg Yakutat City and Borough Yukon-Koyukuk Apache County Cochise County Coconino County Gila County Graham County Greenlee County La Paz County Maricopa County Mohave County Navajo County Pima County Pinal County Santa Cruz County Yavapai County Yuma County Arkansas County Ashley County Baxter County Benton County Boone County Bradley County Calhoun County Carroll County Chicot County Clark County Clay County Cleburne County Cleveland County Columbia County Conway County Craighead County Crawford County Crittenden County Cross County Dallas County Desha County Drew County Faulkner County Franklin County Fulton County Garland County Grant County Greene County Hempstead County Hot Spring County Howard County Independence County Izard County Jackson County Jefferson County Johnson County Lafayette County Lawrence County Lee County Lincoln County Little River County Logan County Lonoke County Madison County Marion County Miller County Mississippi County Monroe County Montgomery County Nevada County Newton County Ouachita County Perry County Phillips County Pike County Poinsett County Polk County Pope County Prairie County Pulaski County Randolph County St. Francis County 55.6 57.1 58.3 63.6 61.5 62.1 56.7 59.8 65.1 35.6 31.8 35.8 33.7 32.9 33.1 33.9 33.5 35.3 35.4 32.2 33.0 31.5 34.7 32.7 34.4 33.2 36.3 36.4 36.3 33.5 33.6 36.4 33.3 34.1 36.4 35.5 33.9 33.2 35.2 35.8 35.5 35.2 35.3 33.9 33.8 33.6 35.1 35.5 36.4 34.5 34.3 36.1 33.7 34.3 34.1 35.8 36.1 35.6 34.2 35.5 33.3 36.1 34.8 34.0 33.7 35.2 34.8 36.0 36.3 33.4 35.8 34.7 34.6 33.7 36.0 33.6 35.0 34.5 34.2 35.6 34.5 35.3 34.8 34.8 36.3 35.0 -132.6 -135.3 -135.5 -143.9 -145.3 -163.7 -133.1 -140.3 -151.9 -109.4 -109.9 -111.5 -111.0 -109.8 -109.3 -114.0 -112.1 -114.1 -110.3 -111.1 -111.5 -110.9 -112.4 -114.4 -91.4 -91.8 -92.4 -94.2 -93.1 -92.1 -92.5 -93.6 -91.3 -93.2 -90.4 -92.1 -92.2 -93.2 -92.7 -90.6 -94.3 -90.3 -90.8 -92.6 -91.4 -91.7 -92.4 -93.9 -91.7 -93.1 -92.5 -90.5 -93.6 -92.9 -94.0 -91.6 -91.9 -91.2 -92.0 -93.5 -93.6 -91.1 -90.8 -91.7 -94.2 -93.8 -91.9 -93.7 -92.7 -94.0 -90.0 -91.2 -93.6 -93.3 -93.2 -92.9 -92.9 -90.8 -93.7 -90.6 -94.3 -93.1 -91.5 -92.3 -91.0 -90.7

IA IA IA IA IA IA IA IA IA IA IA IA IA IA IA IA IA IA IA IA IA IA IA IA IA IA IA IA IA IA IA IA IA IA IA IA IA IA IA IA IA IA IA IA IA IA IA IA IA IA IA IA IA IA IA IA IA IA IA IA IA IA IA IA IA IA IA IA IA IA IA IA IA IA IA IA IA IA IA IA IA IA IA IA KS KS KS KS KS KS
Cedar County Cerro Gordo County Cherokee County Chickasaw County Clarke County Clay County Clayton County Clinton County Crawford County Dallas County Davis County Decatur County Delaware County Des Moines County Dickinson County Dubuque County Emmet County Fayette County Floyd County Franklin County Fremont County Greene County Grundy County Guthrie County Hamilton County Hancock County Hardin County Harrison County Henry County Howard County Humboldt County Ida County Iowa County Jackson County Jasper County Jefferson County Johnson County Jones County Keokuk County Kossuth County Lee County Linn County Louisa County Lucas County Lyon County Madison County Mahaska County Marion County Marshall County Mills County Mitchell County Monona County Monroe County Montgomery County Muscatine County OBrien County Osceola County Page County Palo Alto County Plymouth County Pocahontas County Polk County Pottawattamie County Poweshiek County Ringgold County Sac County Scott County Shelby County Sioux County Story County Tama County Taylor County Union County Van Buren County Wapello County Warren County Washington County Wayne County Webster County Winnebago County Winneshiek County Woodbury County Worth County Wright County Allen County Anderson County Atchison County Barber County Barton County Bourbon County
41.8 43.1 42.7 43.1 41.0 43.1 42.9 41.9 42.0 41.7 40.7 40.7 42.5 40.9 43.4 42.5 43.4 42.8 43.1 42.7 40.7 42.0 42.4 41.7 42.4 43.1 42.4 41.7 41.0 43.4 42.8 42.4 41.7 42.2 41.7 41.0 41.7 42.1 41.3 43.2 40.6 42.0 41.2 41.0 43.4 41.3 41.3 41.3 42.0 41.0 43.3 42.1 41.0 41.0 41.5 43.1 43.4 40.7 43.1 42.8 42.7 41.6 41.3 41.7 40.7 42.4 41.6 41.7 43.1 42.0 42.1 40.7 41.0 40.7 41.0 41.4 41.3 40.7 42.4 43.4 43.3 42.4 43.4 42.7 37.9 38.2 39.5 37.2 38.4 37.9
-91.1 -93.3 -95.6 -92.3 -93.8 -95.2 -91.3 -90.4 -95.4 -94.0 -92.4 -93.8 -91.4 -91.2 -95.1 -90.8 -94.7 -91.9 -92.8 -93.2 -95.6 -94.4 -92.8 -94.5 -93.7 -93.7 -93.2 -95.8 -91.5 -92.3 -94.2 -95.5 -92.1 -90.6 -93.1 -92.0 -91.6 -91.2 -92.2 -94.2 -91.4 -91.6 -91.3 -93.3 -96.2 -94.0 -92.6 -93.1 -93.0 -95.6 -92.8 -96.0 -92.8 -95.2 -91.1 -95.6 -95.6 -95.2 -94.7 -96.2 -94.7 -93.6 -95.7 -92.5 -94.2 -95.1 -90.6 -95.3 -96.2 -93.5 -92.5 -94.7 -94.3 -91.9 -92.4 -93.6 -91.7 -93.3 -94.2 -93.7 -91.8 -96.2 -93.3 -93.8 -95.3 -95.3 -95.3 -98.6 -98.8 -94.8
KS KS KS KS KS KS KS KS KS KS KS KS KS KS KS KS KS KS KS KS KS KS KS KS KS KS KS KS KS KS KS KS KS KS KS KS KS KS KS KS KS KS KS KS KS KS KS KS KS KS KS KS KS KS KS KS KS KS KS KS KS KS KS KS KS KS KS KS KS KS KS KS KS KS KS KS KS KS KS KS KS KS KS KS KS KS KS KS KS KS
Brown County Butler County Chase County Chautauqua County Cherokee County Cheyenne County Clark County Clay County Cloud County Coffey County Comanche County Cowley County Crawford County Decatur County Dickinson County Doniphan County Douglas County Edwards County Elk County Ellis County Ellsworth County Finney County Ford County Franklin County Geary County Gove County Graham County Grant County Gray County Greeley County Greenwood County Hamilton County Harper County Harvey County Haskell County Hodgeman County Jackson County Jefferson County Jewell County Johnson County Kearny County Kingman County Kiowa County Labette County Lane County Leavenworth County Lincoln County Linn County Logan County Lyon County McPherson County Marion County Marshall County Meade County Miami County Mitchell County Montgomery County Morris County Morton County Nemaha County Neosho County Ness County Norton County Osage County Osborne County Ottawa County Pawnee County Phillips County Pottawatomie County Pratt County Rawlins County Reno County Republic County Rice County Riley County Rooks County Rush County Russell County Saline County Scott County Sedgwick County Seward County Shawnee County Sheridan County Sherman County Smith County Stafford County Stanton County Stevens County Sumner County

45.5 43.0 44.0 46.4 44.7 43.3 41.9 47.0 43.8 42.7 43.0 44.4 46.2 43.6 42.2 42.3 44.7 43.0 47.4 44.0 43.1 44.9 41.9 42.6 46.5 46.0 42.6 44.3 46.5 44.0 43.6 45.5 43.6 44.3 41.9 43.3 45.0 43.3 43.5 42.6 43.6 44.3 46.7 44.0 44.7 45.0 42.9 45.4 44.4 43.4 42.9 41.9 43.4 46.1 42.9 43.5 42.3 42.3 42.3 44.3 46.6 45.2 46.9 47.7 45.7 45.4 44.1 44.3 46.6 44.8 46.9 45.0 45.5 46.9 47.5 47.9 44.0 46.5 44.8 44.0 45.9 43.7 43.7 43.7 44.4 45.9 45.0 43.7 47.1 45.6
-84.9 -83.7 -84.4 -89.8 -85.6 -84.6 -84.6 -88.6 -83.1 -84.5 -85.1 -83.6 -88.6 -84.8 -84.4 -85.6 -85.1 -85.6 -88.2 -85.8 -83.2 -85.8 -84.1 -83.9 -85.6 -85.0 -83.0 -86.1 -87.6 -86.3 -85.4 -87.6 -84.3 -85.1 -83.5 -85.2 -84.1 -86.2 -85.8 -83.3 -86.3 -84.1 -89.3 -85.3 -84.2 -84.6 -86.0 -83.9 -84.7 -84.0 -82.6 -85.5 -82.8 -86.2 -84.1 -83.4 -86.0 -83.8 -83.2 -85.6 -93.5 -93.3 -95.7 -94.8 -94.1 -96.4 -94.0 -94.7 -92.6 -93.7 -94.4 -95.6 -92.9 -96.6 -95.4 -90.5 -95.2 -94.1 -93.1 -92.8 -95.4 -94.0 -92.1 -93.4 -92.7 -96.0 -93.4 -91.5 -94.9 -93.3
MN MN MN MN MN MN MN MN MN MN MN MN MN MN MN MN MN MN MN MN MN MN MN MN MN MN MN MN MN MN MN MN MN MN MN MN MN MN MN MN MN MN MN MN MN MN MN MN MN MN MN MN MN MN MN MN MN MS MS MS MS MS MS MS MS MS MS MS MS MS MS MS MS MS MS MS MS MS MS MS MS MS MS MS MS MS MS MS MS MS
Itasca County Jackson County Kanabec County Kandiyohi County Kittson County Koochiching County Lac qui Parle County Lake County Lake of the Woods County Le Sueur County Lincoln County Lyon County McLeod County Mahnomen County Marshall County Martin County Meeker County Mille Lacs County Morrison County Mower County Murray County Nicollet County Nobles County Norman County Olmsted County Otter Tail County Pennington County Pine County Pipestone County Polk County Pope County Ramsey County Red Lake County Redwood County Renville County Rice County Rock County Roseau County St. Louis County Scott County Sherburne County Sibley County Stearns County Steele County Stevens County Swift County Todd County Traverse County Wabasha County Wadena County Waseca County Washington County Watonwan County Wilkin County Winona County Wright County Yellow Medicine County Adams County Alcorn County Amite County Attala County Benton County Bolivar County Calhoun County Carroll County Chickasaw County Choctaw County Claiborne County Clarke County Clay County Coahoma County Copiah County Covington County DeSoto County Forrest County Franklin County George County Greene County Grenada County Hancock County Harrison County Hinds County Holmes County Humphreys County Issaquena County Itawamba County Jackson County Jasper County Jefferson County Jefferson Davis County
47.4 43.7 45.9 45.2 48.8 48.4 45.0 47.5 48.7 44.4 44.4 44.4 44.8 47.3 48.3 43.7 45.1 45.9 46.0 43.7 44.0 44.3 43.7 47.3 44.0 46.4 48.1 46.1 44.0 47.8 45.6 45.0 47.9 44.4 44.7 44.3 43.7 48.8 47.4 44.7 45.4 44.6 45.5 44.0 45.6 45.3 46.1 45.8 44.3 46.5 44.0 45.0 44.0 46.3 44.0 45.2 44.7 31.5 34.9 31.2 33.1 34.8 33.8 33.9 33.5 33.9 33.3 32.0 32.1 33.6 34.2 31.9 31.6 34.9 31.3 31.5 30.9 31.2 33.8 30.4 30.4 32.3 33.1 33.1 32.8 34.3 30.5 32.0 31.7 31.6

-93.6 -95.1 -93.3 -95.0 -96.9 -93.7 -96.2 -91.5 -94.8 -93.7 -96.3 -95.8 -94.3 -95.8 -96.5 -94.5 -94.5 -93.6 -94.3 -92.8 -95.7 -94.1 -95.7 -96.5 -92.4 -95.7 -96.1 -92.8 -96.3 -96.4 -95.4 -93.1 -96.1 -95.2 -94.9 -93.3 -96.2 -95.8 -92.4 -93.5 -93.8 -94.2 -94.5 -93.2 -96.0 -95.7 -94.9 -96.5 -92.2 -95.0 -93.6 -92.9 -94.6 -96.5 -91.7 -93.9 -95.8 -91.4 -88.5 -90.8 -89.6 -89.2 -90.8 -89.3 -89.9 -88.9 -89.3 -90.9 -88.7 -88.7 -90.6 -90.4 -89.5 -90.0 -89.3 -90.9 -88.6 -88.6 -89.8 -89.5 -89.1 -90.3 -90.1 -90.5 -91.0 -88.4 -88.6 -89.1 -91.0 -89.8
MS MS MS MS MS MS MS MS MS MS MS MS MS MS MS MS MS MS MS MS MS MS MS MS MS MS MS MS MS MS MS MS MS MS MS MS MS MS MS MS MS MS MS MS MS MS MS MS MS MO MO MO MO MO MO MO MO MO MO MO MO MO MO MO MO MO MO MO MO MO MO MO MO MO MO MO MO MO MO MO MO MO MO MO MO MO MO MO MO MO
Jones County Kemper County Lafayette County Lamar County Lauderdale County Lawrence County Leake County Lee County Leflore County Lincoln County Lowndes County Madison County Marion County Marshall County Monroe County Montgomery County Neshoba County Newton County Noxubee County Oktibbeha County Panola County Pearl River County Perry County Pike County Pontotoc County Prentiss County Quitman County Rankin County Scott County Sharkey County Simpson County Smith County Stone County Sunflower County Tallahatchie County Tate County Tippah County Tishomingo County Tunica County Union County Walthall County Warren County Washington County Wayne County Webster County Wilkinson County Winston County Yalobusha County Yazoo County Adair County Andrew County Atchison County Audrain County Barry County Barton County Bates County Benton County Bollinger County Boone County Buchanan County Butler County Caldwell County Callaway County Camden County Cape Girardeau County Carroll County Carter County Cass County Cedar County Chariton County Christian County Clark County Clay County Clinton County Cole County Cooper County Crawford County Dade County Dallas County Daviess County DeKalb County Dent County Douglas County Dunklin County Franklin County Gasconade County Gentry County Greene County Grundy County Harrison County
31.7 32.8 34.4 31.2 32.4 31.6 32.7 34.3 33.6 31.5 33.5 32.6 31.2 34.8 33.9 33.5 32.7 32.4 33.1 33.4 34.4 30.7 31.2 31.2 34.2 34.6 34.3 32.3 32.4 32.9 31.9 32.0 30.8 33.6 33.9 34.6 34.8 34.7 34.7 34.5 31.1 32.3 33.4 31.6 33.6 31.2 33.1 34.1 32.8 40.2 40.0 40.4 39.2 36.7 37.5 38.2 38.3 37.3 39.0 39.7 36.7 39.7 38.8 38.1 37.4 39.4 36.9 38.7 37.7 39.5 37.0 40.4 39.3 39.6 38.5 38.9 38.0 37.4 37.7 40.0 39.9 37.6 36.9 36.3 38.4 38.4 40.2 37.2 40.1 40.3

47.2 48.6 46.4 46.4 48.6 46.1 47.0 47.7 46.8 48.6 48.6 47.6 45.4 46.6 47.1 46.9 46.6 45.7 47.0 48.4 48.2 45.4 46.6 46.9 46.2 47.8 48.2 46.0 47.6 48.7 46.0 45.6 45.9 47.8 48.6 46.3 48.3 46.4 47.0 45.8 40.6 42.2 41.6 41.5 41.9 41.7 42.2 42.9 42.5 40.8 41.9 41.2 40.9 42.6 40.5 42.7 41.2 40.5 41.6 41.9 41.4 42.4 42.7 40.8 41.1 42.5 41.5 41.3 40.1 40.5 40.2 40.5 40.2 40.2 41.5 41.8 40.6 41.9 41.6 40.9 40.9 40.2 40.5 40.2 42.5 42.0 41.2 40.2 40.4 40.5
-107.0 -112.8 -109.1 -113.4 -110.0 -112.1 -110.2 -114.1 -112.2 -111.0 -115.4 -105.7 -111.9 -110.9 -115.0 -114.0 -108.4 -110.5 -108.3 -107.8 -112.2 -105.6 -112.8 -105.4 -114.1 -104.5 -105.0 -106.7 -115.1 -104.5 -112.6 -109.4 -109.9 -112.2 -111.8 -107.3 -106.6 -109.9 -104.2 -108.5 -98.5 -98.1 -101.7 -103.7 -100.0 -98.0 -102.9 -98.7 -99.9 -99.1 -96.3 -97.1 -96.1 -97.2 -101.7 -101.1 -103.0 -98.0 -97.1 -96.8 -99.6 -96.5 -103.2 -99.9 -102.3 -96.8 -96.6 -96.1 -101.6 -97.6 -98.9 -100.4 -99.9 -96.7 -102.3 -99.0 -99.8 -101.7 -98.5 -98.4 -98.0 -99.4 -101.1 -101.0 -98.7 -101.1 -98.5 -97.1 -96.3 -99.0
NE NE NE NE NE NE NE NE NE NE NE NE NE NE NE NE NE NE NE NE NE NE NE NE NE NE NE NE NE NE NE NE NE NE NE NE NE NE NE NE NE NE NE NV NV NV NV NV NV NV NV NV NV NV NV NV NV NV NV NV NH NH NH NH NH NH NH NH NH NH NJ NJ NJ NJ NJ NJ NJ NJ NJ NJ NJ NJ NJ NJ NJ NJ NJ NJ NJ NJ
Keith County Keya Paha County Kimball County Knox County Lancaster County Lincoln County Logan County Loup County McPherson County Madison County Merrick County Morrill County Nance County Nemaha County Nuckolls County Otoe County Pawnee County Perkins County Phelps County Pierce County Platte County Polk County Red Willow County Richardson County Rock County Saline County Sarpy County Saunders County Scotts Bluff County Seward County Sheridan County Sherman County Sioux County Stanton County Thayer County Thomas County Thurston County Valley County Washington County Wayne County Webster County Wheeler County York County Churchill County Clark County Douglas County Elko County Esmeralda County Eureka County Humboldt County Lander County Lincoln County Lyon County Mineral County Nye County Pershing County Storey County Washoe County White Pine County Carson City Belknap County Carroll County Cheshire County Coos County Grafton County Hillsborough County Merrimack County Rockingham County Strafford County Sullivan County Atlantic County Bergen County Burlington County Camden County Cape May County Cumberland County Essex County Gloucester County Hudson County Hunterdon County Mercer County Middlesex County Monmouth County Morris County Ocean County Passaic County Salem County Somerset County Sussex County Union County

43.5 43.3 43.1 41.1 42.7 42.6 36.1 35.9 36.5 35.0 36.4 36.1 35.5 36.1 34.6 34.0 35.6 35.7 35.4 35.9 36.4 34.7 36.4 35.7 35.7 35.1 36.1 35.0 35.3 34.3 35.1 35.1 36.4 35.8 35.8 35.9 34.9 36.0 35.9 36.1 36.1 35.3 36.4 35.4 36.3 35.5 36.1 36.3 35.4 35.5 35.3 36.3 35.0 35.5 35.7 35.3 35.5 35.0 35.5 35.3 35.5 35.7 35.2 35.8 35.8 35.2 36.0 35.3 35.2 36.0 34.2 36.4 34.7 36.0 35.1 36.3 34.5 36.2 36.4 35.6 35.3 35.7 35.0 34.7 36.4 35.6 35.4 35.0 34.8 35.3
-73.8 -73.4 -77.1 -73.8 -78.2 -77.1 -79.4 -81.2 -81.1 -80.1 -81.5 -81.9 -76.9 -77.0 -78.6 -78.2 -82.5 -81.6 -80.6 -81.5 -76.2 -76.8 -79.3 -81.2 -79.3 -84.0 -76.6 -83.8 -81.5 -78.7 -77.1 -78.9 -76.0 -75.7 -80.2 -80.5 -78.0 -78.9 -77.6 -80.2 -78.3 -81.2 -76.7 -83.8 -78.7 -77.7 -79.8 -77.7 -78.8 -83.0 -82.5 -77.0 -79.2 -76.2 -80.9 -83.2 -78.4 -77.4 -79.2 -77.6 -81.2 -82.0 -83.4 -82.7 -77.1 -80.8 -82.1 -79.9 -79.5 -77.9 -77.9 -77.5 -77.4 -79.1 -76.8 -76.2 -77.9 -76.5 -79.0 -77.4 -82.2 -79.8 -79.7 -79.1 -79.8 -80.5 -81.9 -78.4 -79.5 -80.2
NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC ND ND ND ND ND ND ND ND ND ND ND ND ND ND ND ND ND ND ND ND ND ND ND ND ND ND ND ND ND ND ND ND ND ND ND ND ND ND ND ND ND ND ND ND ND ND ND ND ND ND ND ND ND OH OH OH OH OH OH OH OH OH OH OH OH OH OH OH OH OH OH OH OH OH
Stokes County Surry County Swain County Transylvania County Tyrrell County Union County Vance County Wake County Warren County Washington County Watauga County Wayne County Wilkes County Wilson County Yadkin County Yancey County Adams County Barnes County Benson County Billings County Bottineau County Bowman County Burke County Burleigh County Cass County Cavalier County Dickey County Divide County Dunn County Eddy County Emmons County Foster County Golden Valley County Grand Forks County Grant County Griggs County Hettinger County Kidder County LaMoure County Logan County McHenry County McIntosh County McKenzie County McLean County Mercer County Morton County Mountrail County Nelson County Oliver County Pembina County Pierce County Ramsey County Ransom County Renville County Richland County Rolette County Sargent County Sheridan County Sioux County Slope County Stark County Steele County Stutsman County Towner County Traill County Walsh County Ward County Wells County Williams County Adams County Allen County Ashland County Ashtabula County Athens County Auglaize County Belmont County Brown County Butler County Carroll County Champaign County Clark County Clermont County Clinton County Columbiana County Coshocton County Crawford County Cuyahoga County Darke County Defiance County Delaware County
36.4 36.4 35.4 35.2 35.8 35.0 36.3 35.8 36.4 35.9 36.2 35.4 36.2 35.7 36.2 35.9 46.1 46.9 48.1 47.0 48.8 46.1 48.8 46.9 46.9 48.8 46.1 48.8 47.3 47.7 46.3 47.5 46.9 47.9 46.4 47.5 46.4 47.0 46.4 46.5 48.2 46.1 47.8 47.6 47.3 46.8 48.2 47.9 47.1 48.8 48.2 48.2 46.5 48.7 46.2 48.8 46.1 47.6 46.1 46.4 46.9 47.5 47.0 48.7 47.5 48.4 48.3 47.6 48.3 38.8 40.8 40.8 41.8 39.4 40.5 40.0 38.9 39.4 40.6 40.1 39.9 39.1 39.4 40.8 40.3 40.8 41.5 40.1 41.3 40.3

33.8 34.4 34.1 33.4 34.9 34.2 32.8 33.8 32.4 34.3 34.7 34.5 34.2 33.9 33.9 34.2 34.6 34.3 34.7 33.5 34.8 34.0 34.0 35.0 33.9 34.7 33.6 35.0 43.7 44.4 43.2 43.0 44.3 45.5 43.8 44.0 44.8 45.8 43.2 44.9 42.9 44.9 45.8 43.7 43.7 45.4 44.7 45.2 43.4 45.4 43.3 45.1 45.2 43.2 44.2 44.7 44.5 43.7 45.6 44.4 43.3 44.6 43.8 44.1 44.0 44.4 44.0 44.4 43.3 43.9 43.7 45.8 45.7 44.4 43.6 44.0 43.6 44.0 44.0 45.6 45.0 45.6 44.0 43.3 44.9 44.4 44.7 43.2 43.4 43.3
-81.9 -81.1 -79.7 -79.3 -82.4 -82.1 -81.1 -78.9 -81.0 -80.6 -80.7 -82.0 -80.3 -81.2 -82.3 -79.3 -79.7 -81.6 -83.0 -80.8 -82.7 -81.0 -81.7 -82.0 -80.4 -81.6 -79.7 -81.1 -98.5 -98.3 -101.7 -97.9 -96.8 -98.4 -99.1 -99.3 -103.6 -100.0 -98.5 -97.7 -97.0 -97.2 -101.1 -103.5 -98.1 -97.6 -96.7 -101.0 -98.4 -99.2 -103.6 -99.1 -96.7 -99.2 -101.5 -97.2 -99.0 -97.8 -103.5 -100.2 -97.7 -99.5 -101.7 -98.6 -100.7 -97.5 -97.1 -103.8 -96.7 -99.8 -97.4 -99.3 -97.6 -103.1 -100.8 -97.6 -96.7 -96.7 -103.1 -102.4 -99.9 -96.9 -98.1 -102.5 -98.4 -100.6 -100.1 -100.8 -99.9 -97.1
SD SD SD SD TN TN TN TN TN TN TN TN TN TN TN TN TN TN TN TN TN TN TN TN TN TN TN TN TN TN TN TN TN TN TN TN TN TN TN TN TN TN TN TN TN TN TN TN TN TN TN TN TN TN TN TN TN TN TN TN TN TN TN TN TN TN TN TN TN TN TN TN TN TN TN TN TN TN TN TN TN TN TN TN TN TN TN TN TN TN
Union County Walworth County Yankton County Ziebach County Anderson County Bedford County Benton County Bledsoe County Blount County Bradley County Campbell County Cannon County Carroll County Carter County Cheatham County Chester County Claiborne County Clay County Cocke County Coffee County Crockett County Cumberland County Davidson County Decatur County DeKalb County Dickson County Dyer County Fayette County Fentress County Franklin County Gibson County Giles County Grainger County Greene County Grundy County Hamblen County Hamilton County Hancock County Hardeman County Hardin County Hawkins County Haywood County Henderson County Henry County Hickman County Houston County Humphreys County Jackson County Jefferson County Johnson County Knox County Lake County Lauderdale County Lawrence County Lewis County Lincoln County Loudon County McMinn County McNairy County Macon County Madison County Marion County Marshall County Maury County Meigs County Monroe County Montgomery County Moore County Morgan County Obion County Overton County Perry County Pickett County Polk County Putnam County Rhea County Roane County Robertson County Rutherford County Scott County Sequatchie County Sevier County Shelby County Smith County Stewart County Sullivan County Sumner County Tipton County Trousdale County Unicoi County
42.8 45.5 43.0 45.0 36.1 35.5 36.1 35.6 35.8 35.2 36.4 35.8 36.0 36.3 36.3 35.4 36.5 36.6 35.9 35.5 35.8 35.9 36.2 35.6 36.0 36.1 36.1 35.2 36.4 35.2 36.0 35.2 36.3 36.2 35.4 36.2 35.1 36.5 35.2 35.2 36.4 35.6 35.6 36.3 35.8 36.3 36.1 36.4 36.1 36.4 36.0 36.3 35.8 35.2 35.5 35.1 35.7 35.4 35.2 36.5 35.6 35.1 35.5 35.6 35.5 35.5 36.5 35.3 36.1 36.4 36.4 35.6 36.6 35.1 36.2 35.6 35.9 36.5 35.9 36.4 35.4 35.8 35.1 36.2 36.5 36.5 36.4 35.5 36.4 36.1

-96.7 -100.1 -97.4 -101.7 -84.2 -86.4 -88.1 -85.2 -84.0 -84.9 -84.1 -86.1 -88.4 -82.2 -87.1 -88.6 -83.7 -85.5 -83.1 -86.1 -89.1 -85.0 -86.8 -88.1 -85.9 -87.4 -89.4 -89.4 -84.9 -86.1 -88.9 -87.0 -83.5 -82.8 -85.7 -83.3 -85.2 -83.2 -89.0 -88.2 -82.9 -89.3 -88.4 -88.3 -87.4 -87.7 -87.8 -85.7 -83.4 -81.8 -84.0 -89.5 -89.5 -87.4 -87.5 -86.6 -84.3 -84.6 -88.6 -86.0 -88.8 -85.6 -86.8 -87.1 -84.8 -84.3 -87.4 -86.4 -84.6 -89.1 -85.3 -87.9 -85.1 -84.5 -85.5 -84.9 -84.5 -86.9 -86.4 -84.5 -85.4 -83.5 -89.9 -86.0 -87.8 -82.4 -86.5 -89.7 -86.2 -82.4
TN TN TN TN TN TN TN TN TN TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX
Union County Van Buren County Warren County Washington County Wayne County Weakley County White County Williamson County Wilson County Anderson County Andrews County Angelina County Aransas County Archer County Armstrong County Atascosa County Austin County Bailey County Bandera County Bastrop County Baylor County Bee County Bell County Bexar County Blanco County Borden County Bosque County Bowie County Brazoria County Brazos County Brewster County Briscoe County Brooks County Brown County Burleson County Burnet County Caldwell County Calhoun County Callahan County Cameron County Camp County Carson County Cass County Castro County Chambers County Cherokee County Childress County Clay County Cochran County Coke County Coleman County Collin County Collingsworth County Colorado County Comal County Comanche County Concho County Cooke County Coryell County Cottle County Crane County Crockett County Crosby County Culberson County Dallam County Dallas County Dawson County Deaf Smith County Delta County Denton County DeWitt County Dickens County Dimmit County Donley County Duval County Eastland County Ector County Edwards County Ellis County El Paso County Erath County Falls County Fannin County Fayette County Fisher County Floyd County Foard County Fort Bend County Franklin County Freestone County
36.3 35.7 35.7 36.3 35.2 36.3 35.9 35.9 36.2 31.8 32.3 31.3 28.0 33.7 35.0 28.9 29.9 34.1 29.7 30.1 33.6 28.4 31.1 29.5 30.2 32.7 31.9 33.4 29.2 30.6 30.0 34.5 27.1 31.8 30.4 30.7 29.8 28.5 32.3 26.1 33.0 35.4 33.1 34.5 29.8 31.9 34.5 33.8 33.7 31.9 31.8 33.1 34.9 29.6 29.8 32.0 31.3 33.6 31.3 34.1 31.4 30.7 33.6 31.3 36.2 32.8 32.7 34.9 33.4 33.1 29.1 33.6 28.5 35.0 27.7 32.3 31.9 30.0 32.4 31.8 32.2 31.3 33.6 29.9 32.8 34.1 34.0 29.6 33.1 31.7